9.5.3 RI Reporting (two CSI subframe sets are configured)
36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification
9.5.3.1_C FDD RI Reporting – PUCCH 1-0 for eICIC
9.5.3.1_C.1 FDD RI Reporting – PUCCH 1-0 for eICIC (non-MBSFN ABS)
9.5.3.1_C.1.1 Test purpose
To verify that the reported rank indicator accurately represents the channel rank under time domain resource restriction i.e. in case two CSI subframe sets are configured.
9.5.3.1_C.1.2 Test applicability
This test applies to all types of E-UTRA FDD UE – Category 2-8 – release 10 and forward. Applicability requires support for FGI bit 115.
9.5.3.1_C.1.3 Minimum conformance requirements
The minimum performance requirement in Table 9.5.3.1_C.1.3-2 is defined as
a) The ratio of the throughput obtained when transmitting based on UE reported RI and that obtained when transmitting with fixed rank 1 shall be ≥ γ1
For the parameters specified in Table 9.5.3.1_C.1.3-1, and using the downlink physical channels specified in Annex C.3.2, the minimum requirements are specified in Table 9.5.3.1_C.1.3-2.
Table 9.5.3.1_C.1.3-1: RI Test (FDD)
|
Parameter |
Unit |
Test 1 |
Test 2 |
||||
|
Cell 1 |
Cell 2 |
Cell 1 |
Cell 2 |
||||
|
Bandwidth |
MHz |
10 |
10 |
||||
|
PDSCH transmission mode |
3 |
Note 10 |
3 |
Note 10 |
|||
|
Downlink power allocation |
|
dB |
-3 |
-3 |
|||
|
|
dB |
-3 |
-3 |
||||
|
σ |
dB |
0 |
0 |
||||
|
Propagation condition and antenna configuration |
2 x 2 EPA5 |
2 x 2 EPA5 |
|||||
|
CodeBookSubsetRestriction bitmap |
01 for fixed RI = 1 10 for fixed RI = 2 11 for UE reported RI |
N/A |
01 for fixed RI = 1 10 for fixed RI = 2 11 for UE reported RI |
N/A |
|||
|
Antenna correlation |
Low |
Low |
|||||
|
RI configuration |
Fixed RI=1 and follow RI |
N/A |
Fixed RI=1 and follow RI |
N/A |
|||
|
|
dB |
0 |
-12 |
20 |
6 |
||
|
|
|
dBmW/15kHz |
-98 (Note 3) |
N/A |
-102 (Note 3) |
N/A |
|
|
|
-98 (Note 4) |
N/A |
-98 (Note 4) |
N/A |
|||
|
|
-98 (Note 5) |
N/A |
-94.8 (Note 5) |
N/A |
|||
|
|
dB[mW/15kHz] |
-98 |
-110 |
-78 |
-92 |
||
|
Subframe Configuration |
Non-MBSFN |
Non-MBSFN |
Non-MBSFN |
Non-MBSFN |
|||
|
Cell Id |
0 |
1 |
0 |
1 |
|||
|
Time Offset between Cells |
μs |
2.5 (synchronous cells) |
2.5 (synchronous cells) |
||||
|
ABS Pattern (Note 6) |
N/A |
10000000 10000000 10000000 10000000 10000000 |
N/A |
10000000 10000000 10000000 10000000 10000000 |
|||
|
RLM/RRM Measurement Subframe Pattern (Note 7) |
10000000 10000000 10000000 10000000 10000000 |
N/A |
10000000 10000000 10000000 10000000 10000000 |
N/A |
|||
|
CSI Subframe Sets (Note 8) |
CCSI,0 |
10000000 10000000 10000000 10000000 10000000 |
N/A |
10000000 10000000 10000000 10000000 10000000 |
N/A |
||
|
CCSI,1 |
01111111 01111111 01111111 01111111 01111111 |
01111111 01111111 01111111 01111111 01111111 |
|||||
|
Number of control OFDM Symbols |
3 |
3 |
3 |
3 |
|||
|
Maximum number of HARQ transmissions |
1 |
1 |
|||||
|
Reporting mode |
PUCCH 1-0 |
PUCCH 1-0 |
|||||
|
Physical channel for CQI reporting |
PUCCH Format 2 |
PUCCH Format 2 |
|||||
|
PUCCH Report Type for CQI |
4 |
4 |
|||||
|
Physical channel for RI reporting |
PUCCH Format 2 |
PUCCH Format 2 |
|||||
|
PUCCH Report Type for RI |
3 |
3 |
|||||
|
Reporting periodicity |
ms |
Npd= 10 |
Npd= 10 |
||||
|
cqi-pmi-ConfigurationIndex |
11 |
11 |
|||||
|
ri-ConfigurationInd |
5 |
5 |
|||||
|
cqi-pmi-ConfigurationIndex2 |
10 |
10 |
|||||
|
ri-ConfigurationInd2 |
2 |
2 |
|||||
|
Cyclic prefix |
Normal |
Normal |
Normal |
Normal |
|||
|
Note 1: If the UE reports in an available uplink reporting instance at subframe SF#n based on CQI estimation at a downlink subframe not later than SF#(n-4), this reported wideband CQI cannot be applied at the eNB downlink before SF#(n+4). Note 2: Reference measurement channel in Cell 1 RC.2 FDD according to Table A.4-1 with one sided dynamic OCNG Pattern OP.1 FDD as described in Annex A.5.1.1. Note 3: This noise is applied in OFDM symbols #1, #2, #3, #5, #6, #8, #9, #10,#12, #13 of a subframe overlapping with the aggressor ABS. Note 4: This noise is applied in OFDM symbols #0, #4, #7, #11 of a subframe overlapping with the aggressor ABS. Note 5: This noise is applied in all OFDM symbols of a subframe overlapping with aggressor non-ABS. Note 6: ABS pattern as defined in TS 36.423 [14]. PDSCH other than SIB1/paging and its associated PDCCH/PCFICH are transmitted in the serving cell subframe when the subframe is overlapped with the ABS subframe of aggressor cell and the subframe is available in the definition of the reference channel. Note 7: Time-domain measurement resource restriction pattern for PCell measurements as defined in TS 36.331 [5]. Note 8: As configured according to the time-domain measurement resource restriction pattern for CSI measurements defined in TS 36.331 [5]. Note 9: Cell 1 is the serving cell. Cell 2 is the aggressor cell. The number of the CRS ports in Cell 1 and Cell 2 is the same. Note 10: Downlink physical channel setup in Cell 2 in accordance with Annex C.3.3 applying OCNG pattern OP.5 FDD as defined in Annex A.5.1.5. |
|||||||
Table 9.5.3.1_C.1.3-2: Minimum requirement (FDD)
|
Test 1 |
Test 2 |
|
|
1 |
0.9 |
1.05 |
|
UE Category |
2-8 |
2-8 |
The normative reference for this requirement is TS 36.101 [2] clause 9.5.3.1.
9.5.3.1_C.1.4 Test description
9.5.3.1_C.1.4.1 Initial conditions
Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.
Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.
Test Environment: Normal as defined in TS 36.508 [7] clause 4.1.
Frequencies to be tested: Mid Range as defined in TS 36.508 [7] clause 4.3.1.1.
Channel Bandwidths to be tested: 10MHz, as defined in TS 36.508 [7] clause 4.3.1.1
1. Connect the SS, faders and AWGN noise source to the UE antenna connector (s) as shown in TS 36.508 [7] Annex A, FigureA.40.
2. The parameter settings for the cell are set up according to Table 9.5.3.1_C.1.3-1.
3. Downlink signals are initially set up according to Annex C0, C.1 and Annex C.3.2, and uplink signals according to Annex H.1 and H.3.2.
4. Propagation conditions are set according to Annex B.0.
5. Ensure the UE is in State 3A-RF (in Cell 1) according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 9.5.3.1_C.1.4.3.
9.5.3.1_C.1.4.2 Test procedure
1. Set the parameters of bandwidth, reference channel, propagation condition, antenna configuration, antenna correlation, CodeBookSubsetRestriction for fixed Rank and the SNR according to Table 9.5.3.1_C.1.3-1 and C.3.3-1 of Annex C.3.3 as appropriate.
2. The SS shall send PDSCH via PDCCH DCI format 2A for C_RNTI to transmit the DL RMC according to the UE reported CQI and fixed RI as defined in Table 9.5.3.1_C.1.3-1. In case of CQI reports for two codewords (codeword #0 and #1), the CQI offset level for codeword #1 is selected from {0,1,2,3,-4,-3,-2,-1}. The SS sends downlink MAC padding bits on the DL RMC.
3. Measure the
according to annex G.5.3.
4. Propagation conditions are set according to Annex B.1.
5. The SS sends uplink scheduling information via PDCCH DCI format 0 to schedule UL RMC in every subframe (Table A.4.1-1).
6. The SS shall transmit an RRC Connection Reconfiguration message to set codebookSubsetRestriction as for UE reported RI according to Table 9.5.3.1_C.1.3-1.
7. The UE shall transmit RRC Connection Reconfiguration Complete message.
8. Propagation conditions are set according to Table 9.5.3.1_C.1.3-1.
9. The SS shall send PDSCH via PDCCH DCI format 2A for C_RNTI to transmit the DL RMC according to the UE reported CQI and RI. In case of CQI reports for two codewords (codeword #0 and #1), the CQI offset level for codeword #1 is selected from {0,1,2,3,-4,-3,-2,-1}. The SS sends downlink MAC padding bits on the DL RMC.
10. Measure
according to Annex G.5.3
If the ratio (
/ 
) satisfies the requirement in Table 9.5.3.1_C.1.5-1, then pass the UE for this test and go to step 11. Otherwise, fail the UE.
11. If all tests have not been done, then repeat the same procedure (steps 1 to 10) with test conditions according to the Table 9.5.3.1_C.1.3-1 for the other Tests as appropriate. Otherwise pass the UE.
9.5.3.1_C.1.4.3 Message contents
Message contents are according to TS 36.508 [7] clause 4.6 with the following exceptions:
Table 9.5.3.1_C.1.4.3-1: PhysicalConfigDedicated-DEFAULT
|
Derivation Path: 36.508 clause 5.5.1.2 Table 5.5.1.2-1 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
PhysicalConfigDedicated-DEFAULT ::= SEQUENCE { |
|||
|
antennaInfo CHOICE { |
|||
|
antennaInfoDedicated ::= SEQUENCE { |
|||
|
transmissionMode |
tm3 |
||
|
codebookSubsetRestriction CHOICE { |
|||
|
n2TxAntenna-tm3 |
According to each test |
||
|
} |
|||
|
ue-TransmitAntennaSelection CHOICE { |
Release |
||
|
release |
NULL |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
cqi-ReportConfig |
Not present |
||
|
cqi-ReportConfig-r10 |
CQI-ReportConfig-r10-DEFAULT |
||
|
} |
|||
Table 9.5.3.1_C.1.4.3-2: RadioResourceConfigDedicated-SRB2-DRB(n, m)
|
Derivation Path: TS 36.508 [7] clause 4.6.3, Table 4.6.3-16 RadioResourceConfigDedicated-SRB2-DRB(n,m) |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RadioResourceConfigDedicated-SRB2-DRB(n, m) ::= SEQUENCE { |
|||
|
MeasSubframePatternPCell-r10 CHOICE { |
|||
|
setup SEQUENCE { |
|||
|
subframePatternFDD-r10 |
‘1000000010000000100000001000000010000000’ |
BIT STRING (SIZE (40)) |
|
|
} |
|||
|
} |
|||
|
} |
|||
Table 9.5.3.1_C.1.4.3-3: CQI-ReportConfig-r10-DEFAULT
|
Derivation Path: 36.508 [7] clause 4.6.3, Table 4.6.3-2AA CQI-ReportConfig-r10-DEFAULT_ |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
CQI-ReportConfig-r10-DEFAULT ::= SEQUENCE { |
|||
|
cqi-ReportAperiodic-r10 |
Not present |
||
|
nomPDSCH-RS-EPRE-Offset |
0 |
||
|
cqi-ReportPeriodic-r10 CHOICE{ |
|||
|
setup SEQUENCE{ |
|||
|
cqi-PUCCH-ResourceIndex-r10 |
0 |
||
|
cqi-PUCCH-ResourceIndexP1-r10 |
Not present |
||
|
cqi-pmi-ConfigIndex |
11 |
||
|
cqi-FormatIndicatorPeriodic-r10 CHOICE { |
|||
|
widebandCQI-r10 SEQUENCE { |
|||
|
csi-ReportMode-r10 |
Not present |
||
|
} |
|||
|
ri-ConfigIndex |
5 |
||
|
simultaneousAckNackAndCQI |
FALSE |
||
|
cqi-Mask-r9 |
Not present |
||
|
csi-ConfigIndex-r10 CHOICE{ |
|||
|
setup SEQUENCE{ |
|||
|
cqi-pmi-ConfigIndex2-r10 |
10 |
||
|
ri-Configindex2-r10 |
2 |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
pmi-RI-Report-r9 |
Not present |
||
|
csi-SubframePatternConfig-r10 CHOICE { |
|||
|
setup SEQUENCE { |
|||
|
csi-MeasSubframeSet1-r10 CHOICE { |
|||
|
subframePatternFDD-r10 |
‘1000000010000000100000001000000010000000’ |
BIT STRING (SIZE (40)) |
|
|
} |
|||
|
csi-MeasSubframeSet2-r10 CHOICE { |
|||
|
subframePatternFDD-r10 |
‘0111111101111111011111110111111101111111’ |
BIT STRING (SIZE (40)) |
|
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
9.5.3.1_C.1.5 Test requirement
Table 9.5.3.1_C.1.5-1: Minimum requirement (FDD)
|
Test 1 |
Test 2 |
|
|
1 |
0.89 |
1.04 |
|
UE Category |
2-8 |
2-8 |
9.5.3.2_C TDD RI Reporting – PUCCH 1-0 for eICIC
9.5.3.2_C.1 TDD RI Reporting – PUCCH 1-0 for eICIC (non-MBSFN ABS)
9.5.3.2_C.1.1 Test purpose
To verify that the reported rank indicator accurately represents the channel rank under time domain resource restriction i.e. in case two CSI subframe sets are configured.
9.5.3.2_C.1.2 Test applicability
This test applies to all types of E-UTRA TDD UE – Category 2-8 -release 10 and forward. Applicability requires support for FGI bit 115.
9.5.3.2_C.1.3 Minimum conformance requirements
The minimum performance requirement in Table 9.5.3.2_C.1.3-2 is defined as:
a) The ratio of the throughput obtained when transmitting based on UE reported RI and that obtained when transmitting with fixed rank 1 shall be ≥ γ1.
For the parameters specified in Table 9.5.3.2_C.1.3-1, and using the downlink physical channels specified in Annex C.3.2, the minimum requirements are specified in Table 9.5.3.2_C.1.3-2.
Table 9.5.3.2_C.1.3-1: RI Test (TDD)
|
Parameter |
Unit |
Test1 |
Test2 |
|||||
|
Cell 1 |
Cell 2 |
Cell 1 |
Cell 2 |
|||||
|
Bandwidth |
MHz |
10 |
10 |
|||||
|
PDSCH transmission mode |
3 |
Note 11 |
3 |
Note 11 |
||||
|
Uplink downlink configuration |
1 |
1 |
||||||
|
Special subframe configuration |
4 |
4 |
||||||
|
Downlink power allocation |
|
dB |
-3 |
-3 |
||||
|
|
dB |
-3 |
-3 |
|||||
|
σ |
dB |
0 |
0 |
|||||
|
Propagation condition and antenna configuration |
2 x 2 EPA5 |
2 x 2 EPA5 |
||||||
|
CodeBookSubsetRestriction bitmap |
01 for fixed RI = 1 10 for fixed RI = 2 11 for UE reported RI |
N/A |
01 for fixed RI = 1 10 for fixed RI = 2 11 for UE reported RI |
N/A |
||||
|
Antenna correlation |
Low |
Low |
||||||
|
RI configuration |
Fixed RI=1 and follow RI |
N/A |
Fixed RI=1 and follow RI |
N/A |
||||
|
|
dB |
0 |
-12 |
20 |
6 |
|||
|
|
|
dB[mW/15kHz] |
-98 (Note 4) |
N/A |
-102 (Note 4) |
N/A |
||
|
|
-98 (Note 5) |
N/A |
-98 (Note 5) |
N/A |
||||
|
|
-98 (Note 6) |
N/A |
-94.8 (Note 6) |
N/A |
||||
|
|
dB[mW/15kHz] |
-98 |
-110 |
-78 |
-92 |
|||
|
Subframe Configuration |
Non-MBSFN |
Non-MBSFN |
Non-MBSFN |
Non-MBSFN |
||||
|
Cell Id |
0 |
1 |
0 |
1 |
||||
|
Time Offset between Cells |
μs |
2.5 (synchronous cells) |
2.5 (synchronous cells) |
|||||
|
ABS Pattern (Note 7) |
N/A |
0000000001 0000000001 |
N/A |
0000000001 0000000001 |
||||
|
RLM/RRM Measurement Subframe Pattern (Note 8) |
0000000001 0000000001 |
N/A |
0000000001 0000000001 |
N/A |
||||
|
CSI Subframe Sets (Note 9) |
CCSI,0 |
0000000001 0000000001 |
N/A |
0000000001 0000000001 |
N/A |
|||
|
CCSI,1 |
1100111000 1100111000 |
1100111000 1100111000 |
||||||
|
Number of control OFDM Symbols |
3 |
3 |
3 |
3 |
||||
|
Maximum number of HARQ transmissions |
1 |
1 |
||||||
|
Reporting mode |
PUCCH 1-0 |
PUCCH 1-0 |
||||||
|
Physical channel for CCSI,0 CQI and RI reporting |
PUCCH Format 2 |
PUCCH Format 2 |
||||||
|
PUCCH Report Type for CQI |
4 |
4 |
||||||
|
Physical channel for CCSI,1 CQI and RI reporting |
PUSCH (Note 3) |
PUSCH (Note 3) |
||||||
|
PUCCH Report Type for RI |
3 |
3 |
||||||
|
Reporting periodicity |
ms |
Npd= 10 |
Npd= 10 |
|||||
|
ACK/NACK feedback mode |
Multiplexing |
Multiplexing |
||||||
|
cqi-pmi-ConfigurationIndex |
8 |
8 |
||||||
|
ri-ConfigurationInd |
5 |
5 |
||||||
|
cqi-pmi-ConfigurationIndex2 |
9 |
9 |
||||||
|
ri-ConfigurationInd2 |
0 |
0 |
||||||
|
Cyclic prefix |
Normal |
Normal |
Normal |
Normal |
||||
|
Note 1: If the UE reports in an available uplink reporting instance at subframe SF#n based on CQI estimation at a downlink subframe not later than SF#(n-4), this reported wideband CQI cannot be applied at the eNB downlink before SF#(n+4). Note 2: Reference measurement channel in Cell 1 RC.2 TDD according to Table A.4-1 with one sided dynamic OCNG Pattern OP.1 TDD as described in Annex A.5.2.1. Note 3: To avoid collisions between RI/CQI reports and HARQ-ACK it is necessary to report them on PUSCH instead of PUCCH. PDCCH DCI format 0 shall be transmitted in downlink SF#9 to allow periodic RI/CQI to multiplex with the HARQ-ACK on PUSCH in uplink subframe #3. Note 4: This noise is applied in OFDM symbols #1, #2, #3, #5, #6, #8, #9, #10,#12, #13 of a subframe overlapping with the aggressor ABS Note 5: This noise is applied in OFDM symbols #0, #4, #7, #11 of a subframe overlapping with the aggressor ABS. Note 6: This noise is applied in all OFDM symbols of a subframe overlapping with aggressor non-ABS. Note 7: ABS pattern as defined in TS 36.423 [14]. PDSCH other than SIB1/paging and its associated PDCCH/PCFICH are transmitted in the serving cell subframe when the subframe is overlapped with the ABS subframe of aggressor cell and the subframe is available in the definition of the reference channel. Note 8: Time-domain measurement resource restriction pattern for PCell measurements as defined in TS 36.331 [5]. Note 9: As configured according to the time-domain measurement resource restriction pattern for CSI measurements defined in TS 36.331 [5]. Note 10: Cell 1 is the serving cell. Cell 2 is the aggressor cell. The number of the CRS ports in Cell 1 and Cell 2 is the same. Note 11: Downlink physical channel setup in Cell 2 in accordance with Annex C.3.3 applying OCNG pattern OP.5 TDD as defined in Annex A.5.2.5. |
||||||||
Table 9.5.3.2_C.1.3-2: Minimum requirement (TDD)
|
Test 1 |
Test 2 |
|
|
1 |
0.9 |
1.05 |
|
UE Category |
2-8 |
2-8 |
The normative reference for this requirement is TS 36.101 [2] clause 9.5.3.2.
9.5.3.2_C.1.4 Test description
9.5.3.2_C.1.4.1 Initial conditions
Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.
Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.
Test Environment: Normal as defined in TS 36.508 [7] clause 4.1.
Frequencies to be tested: Mid Range as defined in TS 36.508 [7] clause 4.3.1.1.
Channel Bandwidths to be tested: 10MHz, as defined in TS 36.508 [7] clause 4.3.1.1
1. Connect the SS, faders and AWGN noise source to the UE antenna connector (s) as shown in TS 36.508 [7] Annex A, Figure A.40.
2. The parameter settings for the cell are set up according to Table 9.5.3.2_C.1.3-1.
3. Downlink signals are initially set up according to Annex C0, C.1 and Annex C.3.2, and uplink signals according to Annex H.1 and H.3.2.
4. Propagation conditions are set according to Annex B.0.
5. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 9.5.3.2_C.1.4.3.
9.5.3.2_C.1.4.2 Test procedure
1. Set the parameters of bandwidth, reference channel, propagation condition, antenna configuration, antenna correlation, CodeBookSubsetRestriction for fixed Rank and the SNR according to Table 9.5.3.2_C.1.3-1 and C.3.3-1 of Annex C.3.3 as appropriate.
2. The SS shall send PDSCH in via PDCCH DCI format 2A for C_RNTI to transmit the DL RMC according to the UE reported CQI and fixed RI as defined in Table 9.5.3.2_C.1.3-1. In case of CQI reports for two codewords (codeword #0 and #1), the CQI offset level for codeword #1 is selected from {0,1,2,3,-4,-3,-2,-1}. The SS sends downlink MAC padding bits on the DL RMC.
The SS sends uplink scheduling information via PDCCH DCI format 0 in subframe #9 with CQI request bit set to 0 to schedule UL RMC in subframe #3 (Table A.4.1-2).
3. Measure the
according to annex G.5.3.
4. Propagation conditions are set according to Annex B.1.
5. The SS sends uplink scheduling information via PDCCH DCI format 0 to schedule UL RMC in subframe #3 and #8 (Table A.4.1-2).
6. The SS shall transmit an RRC Connection Reconfiguration message to set codebookSubsetRestriction as for UE reported RI according to Table 9.5.3.2_C.1.3-1.
7. The UE shall transmit RRC Connection Reconfiguration Complete message.
8. Propagation conditions are set according to Table 9.5.3.2_C.1.3-1.
9. The SS shall send PDSCH via PDCCH DCI format 2A for C_RNTI to transmit the DL RMC according to the UE reported CQI and RI. In case of CQI reports for two codewords (codeword #0 and #1), the CQI offset level for codeword #1 is selected from {0,1,2,3,-4,-3,-2,-1}. The SS sends downlink MAC padding bits on the DL RMC.
The SS sends uplink scheduling information via PDCCH DCI format 0 in subframe #9 with CQI request bit set to 0 to schedule UL RMC in subframe #3 (Table A.4.1-2).
10. Measure
according to Annex G.5.3
If the ratio (
/ 
) satisfies the requirement in Table 9.5.3.2_C.1.5-1, then pass the UE for this test and go to step 11. Otherwise, fail the UE.
11. If all tests have not been done, then repeat the same procedure (steps 1 to 10) with test conditions according to the Table 9.5.3.2_C.1.3-1 for the other Tests as appropriate. Otherwise pass the UE.
9.5.3.2_C.1.4.3 Message contents
Message contents are according to TS 36.508 [7] clause 4.6 with the following exceptions:
Table 9.5.3.2_C.1.4.3-1: PhysicalConfigDedicated-DEFAULT
|
Derivation Path: 36.508 clause 5.5.1.2 Table 5.5.1.2-1 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
PhysicalConfigDedicated-DEFAULT ::= SEQUENCE { |
|||
|
antennaInfo CHOICE { |
|||
|
antennaInfoDedicated ::= SEQUENCE { |
|||
|
transmissionMode |
tm3 |
||
|
codebookSubsetRestriction CHOICE { |
|||
|
n2TxAntenna-tm3 |
According to each test |
||
|
} |
|||
|
ue-TransmitAntennaSelection CHOICE { |
Release |
||
|
release |
NULL |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
cqi-ReportConfig |
Not present |
||
|
cqi-ReportConfig-r10 |
CQI-ReportConfig-r10-DEFAULT |
||
|
} |
|||
Table 9.5.3.2_C.1.4.3-2: RadioResourceConfigDedicated-SRB2-DRB(n, m)
|
Derivation Path: TS 36.508 [7] clause 4.6.3, Table 4.6.3-16 RadioResourceConfigDedicated-SRB2-DRB(n,m) |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RadioResourceConfigDedicated-SRB2-DRB(n, m) ::= SEQUENCE { |
|||
|
MeasSubframePatternPCell-r10 CHOICE { |
|||
|
setup SEQUENCE { |
|||
|
subframePatternTDD-r10 CHOICE{ |
|||
|
subframeConfig1-5-r10 |
‘00000000010000000001’ |
BIT STRING (SIZE (20)) |
|
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 9.5.3.2_C.1.4.3-3: CQI-ReportConfig-r10-DEFAULT
|
Derivation Path: 36.508 [7] clause 4.6.3, Table 4.6.3-2AA CQI-ReportConfig-r10-DEFAULT_ |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
CQI-ReportConfig-r10-DEFAULT ::= SEQUENCE { |
|||
|
cqi-ReportAperiodic-r10 |
Not present |
||
|
nomPDSCH-RS-EPRE-Offset |
0 |
||
|
cqi-ReportPeriodic-r10 CHOICE{ |
|||
|
setup SEQUENCE{ |
|||
|
cqi-PUCCH-ResourceIndex-r10 |
0 |
||
|
cqi-PUCCH-ResourceIndexP1-r10 |
Not present |
||
|
cqi-pmi-ConfigIndex |
8 |
||
|
cqi-FormatIndicatorPeriodic-r10 CHOICE { |
|||
|
widebandCQI-r10 SEQUENCE { |
|||
|
csi-ReportMode-r10 |
Not present |
||
|
} |
|||
|
ri-ConfigIndex |
5 |
||
|
simultaneousAckNackAndCQI |
FALSE |
||
|
cqi-Mask-r9 |
Not present |
||
|
csi-ConfigIndex-r10 CHOICE{ |
|||
|
setup SEQUENCE{ |
|||
|
cqi-pmi-ConfigIndex2-r10 |
9 |
||
|
ri-Configindex2-r10 |
0 |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
pmi-RI-Report-r9 |
Not present |
||
|
csi-SubframePatternConfig-r10 CHOICE { |
|||
|
setup SEQUENCE { |
|||
|
csi-MeasSubframeSet1-r10 CHOICE { |
|||
|
subframePatternTDD-r10 CHOICE { |
|||
|
subframeConfig1-5-r10 |
‘00000000010000000001’ |
BIT STRING (SIZE (20)) |
|
|
} |
|||
|
} |
|||
|
csi-MeasSubframeSet2-r10 CHOICE { |
|||
|
subframePatternTDD-r10 CHOICE { |
|||
|
subframeConfig1-5-r10 |
‘11001110001100111000’ |
BIT STRING (SIZE (20)) |
|
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 9.5.3.2_C.1.4.3-4: TDD-Config-DEFAULT
|
Derivation Path: 36.508 clause 4.6.3 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
TDD-Config-DEFAULT ::= SEQUENCE { |
|||
|
subframeAssignment |
sa1 |
||
|
specialSubframePatterns |
ssp4 |
||
|
} |
|||
9.5.3.2_C.1.5 Test requirement
Table 9.5.3.2_C.1.5-1: Minimum requirement (TDD)
|
Test 1 |
Test 2 |
|
|
1 |
0.89 |
1.04 |
|
UE Category |
2-8 |
2-8 |