F.3.3 Measurement of receiver
36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification
Table F.3.3-1: Derivation of Test Requirements (Receiver tests)
|
Test |
Minimum Requirement in TS 36.101 |
Test Tolerance |
Test Requirement in TS 36.521-1 |
||||
|
7.3 Reference sensitivity power level |
Reference sensitivity power level: For 1.4MHz -102.2dBm -103.2dBm -105.2dBm -106.2dBm For 3MHz -99.2dBm -100.2dBm -102.2dBm For 5MHz -97dBm -98dBm -98.5dBm -99dBm -100dBm -96.5dBm Band 9 with Multi band For 10MHz -94dBm -95dBm -95.5dBm -96dBm -97dBm -93.5dBm Band 9 with Multi band For 15MHz -92.2dBm -93.2dBm -93.7dBm -94.2dBm -95.2dBm -91.7dBm Band 9 with Multi band For 20MHz -91dBm -92dBm -93dBm -94dBm -90.5dBm Band 9 with Multi band T-put limit = 95% of maximum for the Ref Meas channel |
All cases: f ≤ 3.0GHz 0.7dB 3.0GHz < f ≤ 4.2GHz 1.0 dB |
Formula: Reference sensitivity power level + TT T-put limit unchanged |
||||
|
7.3_1 Reference sensitivity level with 4 Rx antenna ports |
Same as 7.3 |
Same as 7.3 |
Same as 7.3 |
||||
|
7.3A.1 Reference sensitivity level for CA (intra-band contiguous DL CA and UL CA) |
PCC and SCC Value in Table 7.3.1-1 PCC and SCC values are each increased by ΔRIB,c in Table 7.3.3-1A or Table 7.3.1-1B where applicable T-put limit = 95% of maximum for the Ref Meas channel |
Same as 7.3 |
PCC and SCC Value in TS 36.101 Table 7.3.1-1+TT PCC and SCC values are each increased by ΔRIB,c in Table 7.3.3-1A where applicable T-put limit unchanged |
||||
|
7.3A.2 Reference sensitivity level for CA (intra-band contiguous DL CA without UL CA) |
Same as 7.3A.1 |
Same as 7.3 |
Same as 7.3A.1 |
||||
|
7.3A.3 Reference sensitivity level for CA (inter-band DL CA without UL CA) |
PCC and SCC Value in Table 7.3.1-1 Exceptions in Tables 7.3.1A-0a, 7.3.1A-0bA, 7.3.1A-0d, 7.3.1A-0eA PCC and SCC values are each increased by ΔRIB,c in Table 7.3.3-1A or Table 7.3.1-1B where applicable T-put limit = 95% of maximum for the Ref Meas channel |
All cases: f ≤ 3.0GHz 0.7dB 3.0GHz < f ≤ 4.2GHz 1.0 dB 4.2GHz < f ≤ 6.0GHz 1.5 dB |
PCC and SCC Value in TS 36.101 Table 7.3.1-1+TT Exceptions in TS 36.101 Tables 7.3.1A-0a, 7.3.1A-0bA, 7.3.1A-0d, 7.3.1A-0eA +TT PCC and SCC values are each increased by ΔRIB,c in Table 7.3.3-1A where applicable T-put limit unchanged |
||||
|
7.3A.4 Reference sensitivity level for CA (intra-band non-contiguous DL CA without UL CA) |
PCC Value in Table 7.3.1-1 SCC Value in Table 7.3.1-1 +ΔRIBNC in Table 7.3.1A-3 PCC and SCC values are each increased by ΔRIB,c in Table 7.3.3-1A or Table 7.3.1-1B where applicable T-put limit = 95% of maximum for the Ref Meas channel |
Same as 7.3 |
PCC Value in TS 36.101 Table 7.3.1-1+TT SCC Value in TS 36.101 Table 7.3.1-1+TT +ΔRIBNC in TS 36.101 Table 7.3.1A-3 PCC and SCC values are each increased by ΔRIB,c in Table 7.3.3-1A where applicable T-put limit unchanged |
||||
|
7.3A.5 Reference sensitivity level for 3DL CA |
PCC and SCCs Value in Table 7.3.1-1 Exceptions in Tables 7.3.1A-0a, 7.3.1A-0bC, 7.3.1A-0d PCC and SCCs values are each increased by ΔRIB,c in Table 7.3.1A-3, 7.3.1-1B or/and ΔRIBNC in Table 7.3.1A-3 where applicable T-put limit = 95% of maximum for the Ref Meas channel |
Same as 7.3A.3 |
PCC and SCC Value in TS 36.101 Table 7.3.1-1+TT Exceptions in TS 36.101 Tables 7.3.1A-0a, 7.3.1A-0bC, 7.3.1A-0d +TT PCC and SCCs values are each increased by ΔRIB,c in Table 7.3.3-1A, 7.3.3-1B or/and ΔRIBNC in TS 36.101 Table 7.3.1A-3 where applicable T-put limit unchanged |
||||
|
7.3A.6 Reference sensitivity level for CA (inter-band DL CA and UL CA) |
TBD |
TBD |
TBD |
||||
|
7.3A.7 Reference sensitivity level for CA (intra-band non-contiguous DL CA and UL CA) |
PCC Value in Table 7.3.1-1+ ΔR2UL_PCC in Table 7.3.1A-4 SCC Value in Table 7.3.1-1 + ΔR2UL_PCC in Table 7.3.1A-4 PCC and SCC values are each increased by ΔRIB,c in Table 7.3.3-1A or Table 7.3.1-1B where applicable T-put limit = 95% of maximum for the Ref Meas channel |
Same as 7.3 |
PCC Value in TS 36.101 Table 7.3.1-1+TT+ ΔR2UL_PCC in Table 7.3.1A-4 SCC Value in TS 36.101 Table 7.3.1-1+TT + ΔR2UL_SCC in Table 7.3.1A-4 PCC and SCC values are each increased by ΔRIB,c in Table 7.3.3-1A where applicable T-put limit unchanged |
||||
|
7.3A.9 Reference sensitivity level for 4DL CA |
PCC and SCCs Value in Table 7.3.1-1 Exceptions in Tables 7.3.1A-0a, 7.3.1A-0bC, 7.3.1A-0d PCC and SCCs values are each increased by ΔRIB,c in Table 7.3.1A-3, 7.3.1-1B or/and ΔRIBNC in Table 7.3.1A-3 where applicable T-put limit = 95% of maximum for the Ref Meas channel |
Same as 7.3A.3 |
PCC and SCC Value in TS 36.101 Table 7.3.1-1+TT Exceptions in TS 36.101 Tables 7.3.1A-0a, 7.3.1A-0bC, 7.3.1A-0d +TT PCC and SCCs values are each increased by ΔRIB,c in Table 7.3.3-1A, 7.3.3-1B or/and ΔRIBNC in TS 36.101 Table 7.3.1A-3 where applicable T-put limit unchanged |
||||
|
7.3A.10 Reference sensitivity level for 5DL CA |
PCC and SCCs Value in Table 7.3.1-1 Exceptions in Tables 7.3.1A-0a, 7.3.1A-0bC, 7.3.1A-0d PCC and SCCs values are each increased by ΔRIB,c in Table 7.3.1A-3, 7.3.1-1B or/and ΔRIBNC in Table 7.3.1A-3 where applicable T-put limit = 95% of maximum for the Ref Meas channel |
Same as 7.3A.3 |
PCC and SCC Value in TS 36.101 Table 7.3.1-1+TT Exceptions in TS 36.101 Tables 7.3.1A-0a, 7.3.1A-0bC, 7.3.1A-0d +TT PCC and SCCs values are each increased by ΔRIB,c in Table 7.3.3-1A, 7.3.3-1B or/and ΔRIBNC in TS 36.101 Table 7.3.1A-3 where applicable T-put limit unchanged |
||||
|
7.3A.11 Reference sensitivity level for 6DL CA |
PCC and SCCs Value in Table 7.3.1-1 Exceptions in Tables 7.3.1A-0a, 7.3.1A-0bC, 7.3.1A-0d PCC and SCCs values are each increased by ΔRIB,c in Table 7.3.1A-3, 7.3.1-1B or/and ΔRIBNC in Table 7.3.1A-3 where applicable T-put limit = 95% of maximum for the Ref Meas channel |
Same as 7.3A.3 |
PCC and SCC Value in TS 36.101 Table 7.3.1-1+TT Exceptions in TS 36.101 Tables 7.3.1A-0a, 7.3.1A-0bC, 7.3.1A-0d +TT PCC and SCCs values are each increased by ΔRIB,c in Table 7.3.3-1A, 7.3.3-1B or/and ΔRIBNC in TS 36.101 Table 7.3.1A-3 where applicable T-put limit unchanged |
||||
|
7.3B Reference Sensitivity Level for UL-MIMO |
Same as 7.3 |
Same as 7.3 |
Same as 7.3 |
||||
|
7.3D.1 Reference sensitivity level for ProSe Direct Discovery |
Values as defined in table 7.3D.0.1 |
All cases: f ≤ 3.0GHz 0.7dB |
Formula: Reference sensitivity power level + TT T-put limit unchanged |
||||
|
7.3D.2 Reference sensitivity level for ProSe Direct Communication |
Values as defined in table 7.3D.0.2 |
Same as 7.3D.1 |
Same as 7.3D.1 |
||||
|
7.3E Reference Sensitivity Level for UE category 0 |
Same as 7.3 |
Same as 7.3 |
Same as 7.3 |
||||
|
7.3EA Reference Sensitivity Level for UE category M1 |
Reference sensitivity power level as specified T-put limit = 95% of maximum for the Ref Meas channel |
All cases: f ≤ 3.0GHz 0.7dB 3.0GHz < f ≤ 4.2GHz 1.0 dB |
Formula: Reference sensitivity power level + TT T-put limit unchanged |
||||
|
7.3EB Reference sensitivity level for UE category 1bis |
Same as 7.3 |
Same as 7.3 |
Same as 7.3 |
||||
|
7.3EC Reference Sensitivity Level for UE category M2 |
Same as 7.3EA |
Same as 7.3EA |
Same as 7.3EA |
||||
|
7.3F.1 Reference sensitivity level without repetitions for UE category NB1 and NB2 |
Reference sensitivity power level: -108.2dBm T-put limit = 95% of maximum for the Ref Meas channel |
f ≤ 3.0GHz 0.7dB |
Formula: Reference sensitivity power level + TT T-put limit unchanged |
||||
|
7.3F.2 Void |
|||||||
|
7.3G.1 Reference sensitivity level for V2X Communication / Non-concurrent with E-UTRA uplink transmissions |
Reference sensitivity power level: For 10MHz -90.4dBm For 20MHz -87.5dBm T-put limit = 95% of maximum for the Ref Meas channel |
All cases: 4.2GHz < f ≤ 6GHz 1.5 dB |
Formula: Reference sensitivity power level + TT T-put limit unchanged |
||||
|
7.3G.2 Reference sensitivity level for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions |
Reference sensitivity power level for V2X sidelink: For 10MHz -90.4dBm For 20MHz -87.5dBm Reference sensitivity power level for E-UTRA: For 1.4MHz -101.7dBm -102.2dBm For 3MHz -98.7dBm -99.2dBm -100.2dBm For 5MHz -97dBm -97.2dBm -98dBm -98.5dBm -100dBm For 10MHz -90.4dBm -94dBm -94.2dBm -95dBm -95.5dBm -97dBm For 15MHz -91.2dBm -92.2dBm -93.2dBm -93.7dBm -95.2dBm For 20MHz -87.5dBm -90dBm -91dBm -92dBm -94dBm T-put limit = 95% of maximum for the Ref Meas channel |
All cases: 4.2GHz < f ≤ 6GHz 1.5 dB f ≤ 3.0GHz 0.7dB 3.0GHz < f ≤ 4.2GHz 1.0 dB |
Formula: Reference sensitivity power level + TT T-put limit unchanged |
||||
|
7.3G.3 Reference sensitivity level for V2X Communication / Intra-band contiguous multi-carrier operation |
Same as 7.3G.1 |
Same as 7.3G.1 |
Same as 7.3G.1 |
||||
|
7.4 Maximum input level |
Signal level -25dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Maximum input level – TT Signal level: f ≤ 3.0GHz: -25.7 dBm 3.0GHz < f ≤ 4.2GHz: -26.0 dBm T-put limit unchanged Uplink power measurement window comprises four quantities: 1. UE power step size 1dB 2. UE Power step tolerance ±1dB 3. Test system power measurement at top of window: f ≤ 3.0GHz ±0.7 dB 3.0GHz < f ≤ 4.2GHz ±1.0 dB. 4. Test system power measurement at bottom of window: f ≤ 3.0GHz ±0.7 dB 3.0GHz < f ≤ 4.2GHz ±1.0 dB. Items 1 to 4 are added arithmetically: Overall UL power window size: f ≤ 3.0GHz: (1dB+1dB+0.7dB+0.7dB) =3.4dB 3.0GHz < f ≤ 4.2GHz: (1dB+1dB+1dB+1dB) =4dB Top of window is aligned to UL power requirement, hence +0dB, -3.4dB or +0dB, -4.0dB according to frequency |
||||
|
7.4_1 Maximum input level with 4 Rx antenna ports |
Same as 7.4 |
Same as 7.4 |
Same as 7.4 |
||||
|
7.4A.1 Maximum input level for CA (intra band contiguous DL CA and UL CA) |
Signal level for each CC as specified T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz 0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Signal level for each CC – TT T-put limit unchanged Uplink power measurement window is calculated in the same way as 7.4, but the target power for each CC is scaled according to the allocation: For PCC: 10log(P_LCRB/NRB_alloc) For SCC: 10log(S_LCRB/NRB_alloc) |
||||
|
7.4A.1 H Maximum input level for SCE-L1 for CA (intra-band contiguous DL CA and UL CA) |
Signal level for each CC as specified T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz 0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Signal level for each CC – TT Signal level: f ≤ 3.0GHz: -27.7 dBm 3.0GHz < f ≤ 4.2GHz: -28.0 dBm T-put limit unchanged Uplink power measurement window is calculated in the same way as 7.4, but the target power for each CC is scaled according to the allocation: For PCC: 10log(P_LCRB/NRB_alloc) For SCC: 10log(S_LCRB/NRB_alloc) |
||||
|
7.4A.2 Maximum input level for CA (intra band contiguous DL CA without UL CA) |
Signal level for each CC as specified T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz 0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Signal level for each CC – TT T-put limit unchanged Uplink power measurement window same as 7.4 |
||||
|
7.4A.2 H Maximum input level for SCE-L1 for CA (intra-band contiguous DL CA without UL CA) |
Signal level for each CC as specified T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz 0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Signal level for each CC – TT T-put limit unchanged Uplink power measurement window same as 7.4 |
||||
|
7.4A.3 Maximum input level for CA (inter-band DL CA without UL CA) |
Signal level -25dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz 0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB 4.2GHz < f ≤ 6.0GHz 1.5 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Maximum input level – TT Signal level: f ≤ 3.0GHz: -25.7 dBm 3.0GHz < f ≤ 4.2GHz: -26.0 dBm4.2GHz < f ≤ 6.0GHz: -26.5 dBm T-put limit unchanged Uplink power measurement window same as 7.4 |
||||
|
7.4A.4 Maximum input level for CA (intra band non-contiguous DL CA without UL CA) |
Signal level -25dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz 0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Maximum input level – TT Signal level: f ≤ 3.0GHz: -25.7 dBm 3.0GHz < f ≤ 4.2GHz: -26.0 dBm T-put limit unchanged Uplink power measurement window same as 7.4 |
||||
|
7.4A.5 Maximum input level for 3DL CA |
Signal level for each CC as specified T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz 0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB 4.2GHz < f ≤ 6.0GHz 1.5 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Signal level for each CC – TT T-put limit unchanged Uplink power measurement window same as 7.4 |
||||
|
7.4A.5_H Maximum input level for SCE-L1 for 3DL CA |
Signal level for each CC as specified T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz 0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Signal level for each CC – TT T-put limit unchanged Uplink power measurement window is calculated in the same way as 7.4 |
||||
|
7.4A.7 Maximum input level for for 4DL CA |
Signal level for each CC as specified T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz 0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB 4.2GHz < f ≤ 6.0GHz 1.5 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Signal level for each CC – TT T-put limit unchanged Uplink power measurement window is calculated in the same way as 7.4 |
||||
|
7.4A.7_H Maximum input level for 4DL CA for 256QAM in DL |
Same as 7.4A.7 |
Same as 7.4A.7 |
Same as 7.4A.7 |
||||
|
7.4A.8 Maximum input level for for 5DL CA |
Signal level for each CC as specified T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz 0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB 4.2GHz < f ≤ 6.0GHz 1.5 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Signal level for each CC – TT T-put limit unchanged Uplink power measurement window is calculated in the same way as 7.4 |
||||
|
7.4A.8_H Maximum input level for 5DL CA for 256QAM in DL |
Signal level for each CC as specified T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz 0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Signal level for each CC – TT T-put limit unchanged Uplink power measurement window is calculated in the same way as 7.4 |
||||
|
7.4A.9 Maximum input level for for 6DL CA |
Signal level for each CC as specified T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz 0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB 4.2GHz < f ≤ 6.0GHz 1.5 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Signal level for each CC – TT T-put limit unchanged Uplink power measurement window is calculated in the same way as 7.4 |
||||
|
7.4A.9_H Maximum input level for 6DL CA for 256QAM in DL |
Signal level for each CC as specified T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz 0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Signal level for each CC – TT T-put limit unchanged Uplink power measurement window is calculated in the same way as 7.4 |
||||
|
7.4B Maximum Input Level for UL-MIMO |
Same as 7.4 |
Same as 7.4 |
Same as 7.4 Uplink power measurement window applies to overall UL power, which is the linear sum of the output powers over all Tx antenna connectors |
||||
|
7.4D.1 Maximum input level for ProSe Direct Discovery |
Signal level -22dBm T-put limit = 95% of maximum for the Ref Meas channel |
f ≤ 3.0GHz 0.7 dB |
Formula: Maximum input level – TT Signal level: f ≤ 3.0GHz: -22.7 dBm T-put limit unchanged |
||||
|
7.4D.2 Maximum input level for ProSe Direct Communication |
Same as 7.4D.1 |
Same as 7.4D.1 |
Same as 7.4D.1 |
||||
|
7.4E Maximum input level for UE category 0 |
Same as 7.4 |
Same as 7.4 |
Same as 7.4 |
||||
|
7.4EA Maximum input level for UE category M1 |
Same as 7.4 |
Same as 7.4 |
Same as 7.4 |
||||
|
7.4EB Maximum input level for UE category 1bis |
Same as 7.4 |
Same as 7.4 |
Same as 7.4 |
||||
|
7.4EC Maximum input level for UE category M2 |
Same as 7.4 |
Same as 7.4 |
Same as 7.4 |
||||
|
7.4_H Maximum input level for SCE-L1 |
Signal level -27dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
f ≤ 3.0GHz 0.7 dB 3.0GHz < f ≤ 4.2GHz 1.0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Maximum input level – TT Signal level: f ≤ 3.0GHz: -27.7 dBm 3.0GHz < f ≤ 4.2GHz: -28.0 dBm T-put limit unchanged Uplink power measurement window same as 7.4 |
||||
|
7.4F Maximum imput level for UE category NB1 and NB2 |
Signal level -25dBm T-put limit = 95% of maximum for the Ref Meas channel |
f ≤ 3.0GHz 0.7 dB |
Formula: Maximum input level – TT Signal level: f ≤ 3.0GHz: -25.7dBm T-put limit unchanged |
||||
|
7.4G.1 Maximum input level for V2X Communication / Non-concurrent with E-UTRA uplink transmissions |
Signal level -22dBm T-put limit = 95% of maximum for the Ref Meas channel |
4.2GHz < f ≤ 6GHz 1.5 dB |
Formula: Maximum input level – TT Signal level: 4.2GHz < f ≤ 6GHz : -23.5dBm T-put limit unchanged |
||||
|
7.4G.2 Maximum input level for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions |
Signal level -22dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
4.2GHz < f ≤ 6GHz 1.5 dB for V2X sidelink f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB 4.2GHz < f ≤ 6GHz 0dB, -4.3dB |
Same as 7.4G.1 for V2X sidelink Same as 7.4 for E-UTRA |
||||
|
7.4G.3 Maximum input level for V2X Communication / Intra-band contiguous multi-carrier operation |
Same as 7.4G.1 |
Same as 7.4G.1 |
Same as 7.4G.1 |
||||
|
7.5 Adjacent Channel Selectivity (ACS) |
Case 1: Wanted signal power, all BWs: (REFSENS + 14 dB) Interferer signal power For 1.4 MHz, 3 MHz, 5 MHz, 10 MHz BW: (REFSENS + 45.5 dB) For 15 MHz BW: (REFSENS + 42.5 dB) For 20 MHz BW: (REFSENS + 39.5 dB) Case 2: Wanted signal power For 1.4 MHz, 3 MHz, 5 MHz, 10 MHz BW: -56.5 dBm For 15 MHz BW: -53.5 dBm For 20 MHz BW: -50.5 dBm Interferer signal power, all BWs: -25 dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged Uplink power measurement window same as 7.4 |
||||
|
7.5_1 Adjacent Channel Selectivity (ACS) with 4 Rx antenna ports |
Same as 7.5 |
Same as 7.5 |
Same as 7.5 |
||||
|
7.5A.1 Adjacent Channel Selectivity (ACS) for CA (intra-band contiguous DL CA and UL CA) |
Case 1: Wanted signal power: (REFSENS + 14 dB) Interferer signal power For CA BW Class C: (Aggregated power + 22.5 dB) Case 2: Wanted signal power: -47.5 +10log(NRB,c/NRB agg) dBm Interferer signal power For CA BW Class C: -25 dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged Uplink power measurement window same as 7.4A.1 |
||||
|
7.5A.2 Adjacent Channel Selectivity (ACS) for CA (intra band contiguous DL CA without UL CA) |
Same as 7.5A.1 |
Same as 7.5A.1 |
Same as 7.5A.1 |
||||
|
7.5A.3 Adjacent Channel Selectivity (ACS) for CA (inter band DL CA without UL CA) |
Same as 7.5 for each CC |
Same as 7.5 |
Same as 7.5 for each CC |
||||
|
7.5A.4 Adjacent Channel Selectivity (ACS) for CA (intra-band non-contiguous DL CA without UL CA) |
Same as 7.5 for each CC |
Same as 7.5 |
Same as 7.5 for each CC |
||||
|
7.5A.5 Adjacent Channel Selectivity (ACS) for 3DL CA |
Intra-band contiguous DL CA Case 1: Wanted signal power: (REFSENS + 14 dB) Interferer signal power For CA BW Class B, Class C: (Aggregated power + 22.5 dB) For CA BW Class D: (Aggregated power + 20.7 dB) Case 2: Wanted signal power: For CA BW Class B: -50.5 +10log(NRB,c/NRB agg) dBm For CA BW Class C: -47.5 +10log(NRB,c/NRB agg) dBm For CA BW Class D: -43.9 +10log(NRB,c/NRB agg) dBm Interferer signal power -25 dBm Inter-band CA Same as 7.5 for each CC T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged Uplink power measurement window same as 7.4A.1 |
||||
|
7.5A.7 Adjacent Channel Selectivity (ACS) for 4DL CA |
Same as 7.5A.5 for each CC |
Same as 7.5A.5 |
Same as 7.5A.5 for each CC |
||||
|
7.5A.8 Adjacent Channel Selectivity (ACS) for 5DL CA |
Same as 7.5A.5 for each CC except for following additional requirements Intra-band contiguous DL CA Case 1: For CA BW Class F: (Aggregated power + 18.5 dB) Case 2: Wanted signal power: For CA BW Class F: -43.5 +10log(NRB,c/NRB agg) dBm |
Same as 7.5A.5 |
Same as 7.5A.5 for each CC |
||||
|
7.5A.9 Adjacent Channel Selectivity (ACS) for 6DL CA |
Same as 7.5A.8 |
Same as 7.5A.5 |
Same as 7.5A.5 for each CC |
||||
|
7.5B Adjacent Channel Selectivity (ACS) for UL-MIMO |
Same as 7.5 |
Same as 7.5 |
Same as 7.5 Uplink power measurement window applies to overall UL power, which is the linear sum of the output powers over all Tx antenna connectors |
||||
|
7.5D.1 Adjacent channel selectivity (ACS) for ProSe Direct Discovery |
Signal levels as defined in minimum requirements T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.5D.2 Adjacent channel selectivity (ACS) for ProSe Direct Communication |
Signal levels as defined in minimum requirements T-put limit = 95% of maximum for the Ref Meas channel |
Same as 7.5D.1 |
Same as 7.5D.1 |
||||
|
7.5E Adjacent Channel Selectivity (ACS) for UE category 0 |
Same as 7.5 |
Same as 7.5 |
Same as 7.5 |
||||
|
7.5EA Adjacent Channel Selectivity (ACS) for UE category M1 |
Same as 7.5 |
Same as 7.5 |
Same as 7.5 |
||||
|
7.5EB Adjacent Channel Selectivity (ACS) for UE category 1bis |
Same as 7.5 |
Same as 7.5 |
Same as 7.5 |
||||
|
7.5EC Adjacent Channel Selectivity (ACS) for UE category M2 |
Same as 7.5 |
Same as 7.5 |
Same as 7.5 |
||||
|
7.5F Adjacent Channel Selectivity (ACS) for UE category NB1 and NB2 |
ACS 1: Wanted signal power: (REFSENS + 14 dB) Interferer signal power For GSM interferer: (REFSENS + 42 dB) For E-UTRA interferer: (REFSENS + 47 dB) ACS 2: Wanted signal power For GSM interferer: -53 dBm For E-UTRA interferer: -58 dBm Interferer signal power: -25 dBm T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.5G.1 Adjacent channel selectivity (ACS) for V2X Communication / Non-concurrent with E-UTRA uplink transmissions |
Case 1: Wanted signal power, all BWs: (REFSENS + 14 dB) Interferer signal power For 10 MHz BW: (REFSENS + 45.5 dB) For 20 MHz BW: (REFSENS + 39.5 dB) Case 2: Wanted signal power For 10 MHz BW: -56.5 dBm For 20 MHz BW: -50.5 dBm Interferer signal power, all BWs: -25 dBm T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.5G.2 Adjacent channel selectivity (ACS) for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions |
Case 1: Wanted signal power, all BWs: (REFSENS + 14 dB) Interferer signal power For 10 MHz BW: (REFSENS + 45.5 dB) For 20 MHz BW: (REFSENS + 39.5 dB) Case 2: Wanted signal power For 10 MHz BW: -56.5 dBm For 20 MHz BW: -50.5 dBm Interferer signal power, all BWs: -25 dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB 4.2GHz < f ≤ 6GHz 0dB, -4.3dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.5G.3 Adjacent channel selectivity (ACS) for V2X Communication / Intra-band contiguous multi-carrier operation |
Same as 7.5G.1 |
Same as 7.5G.1 |
Same as 7.5G.1 |
||||
|
7.6.1 In-band blocking |
Wanted signal power: (REFSENS + BW dependent value) Interferer signal power: -56dBm or -44dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged Uplink power measurement window same as 7.4 |
||||
|
7.6.1_1 In-band blocking with 4 Rx antenna ports |
Same as 7.6.1 |
Same as 7.6.1 |
Same as 7.6.1 |
||||
|
7.6.1A.1 In-band blocking for CA (intra band contiguous DL CA and UL CA) |
Wanted signal power: (REFSENS + CA BW Class specific value) Interferer signal power: -56dBm or -44dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
Same as 7.6.1 |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged Uplink power measurement window same as 7.4A.1 |
||||
|
7.6.1A.2 In-band blocking for CA (intra band contiguous DL CA without UL CA) |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
||||
|
7.6.1A.3 In-band blocking for CA (inter band DL CA without UL CA) |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
||||
|
7.6.1A.4 In-band blocking for CA (intra-band non-contiguous DL CA without UL CA) |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
||||
|
7.6.1A.5 In-band blocking for 3DL CA |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
||||
|
7.6.1A.7 In-band blocking for 4DL CA |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
||||
|
7.6.1A.8 In-band blocking for 5DL CA |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
||||
|
7.6.1A.9 In-band blocking for 6DL CA |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
||||
|
7.6.1A.10 In-band blocking for 7DL CA |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
Same as 7.6.1A.1 |
||||
|
7.6.1B In-band blocking for UL-MIMO |
Same as 7.6.1 |
Same as 7.6.1 |
Same as 7.6.1 Uplink power measurement window applies to overall UL power, which is the linear sum of the output powers over all Tx antenna connectors |
||||
|
7.6.1D.1 In-band blocking for ProSe Direct Discovery |
Signal levels as defined in minimum requirements T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.6.1D.2 In-band blocking for ProSe Direct Communication |
Signal levels as defined in minimum requirements T-put limit = 95% of maximum for the Ref Meas channel |
Same as 7.6.1D.1 |
Same as 7.6.1D.1 |
||||
|
7.6.1E In-band blocking for UE category 0 |
Same as 7.6.1 |
Same as 7.6.1 |
Same as 7.6.1 |
||||
|
7.6.1F In-band blocking for category NB1 and NB2 |
Wanted signal power: (REFSENS + 6dB) Interferer signal power: -56dBm or -44dBm T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.6.1EA In-band blocking for UE category M1 |
Wanted signal power: (REFSENS + CA BW Class specific value) Interferer signal power: -56dBm or -44dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB f ≤ 3.0GHz 0dB, -3.4dB |
Same as 7.6.1 |
||||
|
7.6.1EB In-band blocking for UE category 1bis |
Same as 7.6.1 |
Same as 7.6.1 |
Same as 7.6.1 |
||||
|
7.6.1EC In-band blocking for UE category M2 |
Same as 7.6.1EA |
Same as 7.6.1EA |
Same as 7.6.1 |
||||
|
7.6.1G.1 In-band blocking for V2X Communication / Non-concurrent with E-UTRA uplink transmissions |
Wanted signal power: (REFSENS + BW dependent value) Interferer signal power: -56dBm or -44dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.6.1G.2 In-band blocking for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions |
Wanted signal power: (REFSENS + BW dependent value) Interferer signal power: -56dBm or -44dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB 4.2GHz < f ≤ 6GHz 0dB, -4.3dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.6.1G.3 In-band blocking for V2X Communication / Intra-band contiguous multi-carrier operation |
Same as 7.6.1G.1 |
Same as 7.6.1G.1 |
Same as 7.6.1G.1 |
||||
|
7.6.2 Out of-band blocking |
Wanted signal power: (REFSENS + BW dependent value) Interferer signal power: -44dBm, -30dBm or -15dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged Uplink power measurement window same as 7.4 |
||||
|
7.6.2_1 Out of-band blocking with 4 Rx antenna ports |
Same as 7.6.2 |
Same as 7.6.2 |
Same as 7.6.2 |
||||
|
7.6.2A.1 Out-of-band blocking for CA (intra band contiguous DL CA and UL CA) |
Wanted signal power: (REFSENS + CA BW Class specific value) Interferer signal power: -44dBm, -30dBm or -15dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
Same as 7.6.2 |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged Uplink power measurement window same as 7.4A.1 |
||||
|
7.6.2A.2 Out-of-band blocking for CA (intra band contiguous DL CA without UL CA) |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
||||
|
7.6.2A.3 Out-of-band blocking for CA (inter band DL CA without UL CA) |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
||||
|
7.6.2A.4 Out-of-band blocking for CA (intra-band non-contiguous DL CA without UL CA) |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
||||
|
7.6.2A.5 Out-of-band blocking for 3DL CA |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
||||
|
7.6.2A.7 Out-of-band blocking for 4DL CA |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
||||
|
7.6.2A.8 Out-of-band blocking for 5DL CA |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
||||
|
7.6.2A.9 Out-of-band blocking for 6DL CA |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
||||
|
7.6.2A.10 Out-of-band blocking for 7DL CA |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
Same as 7.6.2A.1 |
||||
|
7.6.2B Out-of-band blocking for UL-MIMO |
Same as 7.6.2 |
Same as 7.6.2 |
Same as 7.6.2 Uplink power measurement window applies to overall UL power, which is the linear sum of the output powers over all Tx antenna connectors |
||||
|
7.6.2D.1 Out-of-band blocking for ProSe Direct Discovery |
Signal levels as defined in minimum requirements T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.6.2D.2 Out-of-band blocking for ProSe Direct Communication |
Signal levels as defined in minimum requirements T-put limit = 95% of maximum for the Ref Meas channel |
Same as 7.6.2D.1 |
Same as 7.6.1D.1 |
||||
|
7.6.2E Out of-band blocking for UE category 0 |
Same as 7.6.2 |
Same as 7.6.2 |
Same as 7.6.2 |
||||
|
7.6.2F Out of-band blocking for category NB1 and NB2 |
Wanted signal power: (REFSENS + 6dB) Interferer signal power: -44dBm, -30dBm or -15dBm T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.6.2G.1 Out-of-band blocking for V2X Communication/ Non-concurrent with E-UTRA uplink transmissions |
Wanted signal power: (REFSENS + BW dependent value) Interferer signal power: -44dBm, -30dBm or -15dBm T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.6.2G.2 Out-of-band blocking for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions |
Wanted signal power: (REFSENS + BW dependent value) Interferer signal power: -44dBm, -30dBm or -15dBm T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.6.2G.3 Out-of-band blocking for V2X Communication / Intra-band contiguous multi-carrier operation |
Wanted signal power: (REFSENS + BW dependent value) Interferer signal power: -44dBm, -30dBm or -15dBm T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.6.2EA Out-of-band blocking for UE category M1 |
Wanted signal power: (REFSENS + BW dependent value) Interferer signal power: -44dBm, -30dBm or -15dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB f ≤ 3.0GHz 0dB, -3.4dB |
Same as 7.6.2 |
||||
|
7.6.2EB Out-of-band blocking for UE category 1bis |
Same as 7.6.2 |
Same as 7.6.2 |
Same as 7.6.2 |
||||
|
7.6.2EC Out-of-band blocking for UE category M2 |
Same as 7.6.2EA |
Same as 7.6.2EA |
Same as 7.6.2 |
||||
|
7.6.3 Narrow band blocking |
Wanted signal power,: (REFSENS + BW dependent value) Interferer signal power: -55dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged Uplink power measurement window same as 7.4 |
||||
|
7.6.3_1 Narrow band blocking with 4 Rx antenna ports |
Same as 7.6.3 |
Same as 7.6.3 |
Same as 7.6.3 |
||||
|
7.6.3A.1 Narrow band blocking for CA (intra band contiguous DL CA and UL CA) |
Wanted signal power: (REFSENS + CA BW Class specific value) Interferer signal power: -55dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
Same as 7.6.3 |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged Uplink power measurement window same as 7.4A.1 |
||||
|
7.6.3A.2 Narrow band blocking for CA (intra band contiguous DL CA without UL CA) |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
||||
|
7.6.3A.3 Narrow band blocking for CA (inter band DL CA without UL CA) |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
||||
|
7.6.3A.4 Narrow band blocking for CA (intra-band non-contiguous DL CA without UL CA) |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
||||
|
7.6.3A.5 Narrow band blocking for 3DL CA |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
||||
|
7.6.3A.7 Narrow band blocking for 4DL CA |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
||||
|
7.6.3A.8 Narrow band blocking for 5DL CA |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
||||
|
7.6.3A.9 Narrow band blocking for 6DL CA |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
||||
|
7.6.3A.10 Narrow band blocking for 7DL CA |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
Same as 7.6.3A.1 |
||||
|
7.6.3B Narrow band blocking for UL-MIMO |
Same as 7.6.3 |
Same as 7.6.3 |
Same as 7.6.3 Uplink power measurement window applies to overall UL power, which is the linear sum of the output powers over all Tx antenna connectors |
||||
|
7.6.3D.1 Narrow band blocking for ProSe Direct Discovery |
Signal levels as defined in minimum requirements T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.6.3D.2 Narrow band blocking for ProSe Direct Communication |
Signal levels as defined in minimum requirements T-put limit = 95% of maximum for the Ref Meas channel |
Same as 7.6.3D.1 |
Same as 7.6.3D.1 |
||||
|
7.6.3E Narrow band blocking for UE category 0 |
Same as 7.6.3 |
Same as 7.6.3 |
Same as 7.6.3 |
||||
|
7.6.3EA Narrow band blocking for UE category M1 |
Wanted signal power,: (REFSENS + BW dependent value) Interferer signal power: -55dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB f ≤ 3.0GHz 0dB, -3.4dB |
Same as 7.6.3 |
||||
|
7.6.3EB Narrow band blocking for UE category 1bis |
Same as 7.6.3 |
Same as 7.6.3 |
Same as 7.6.3 |
||||
|
7.6.3EC Narrow band blocking for UE category M2 |
Same as 7.6.3EA |
Same as 7.6.3EA |
Same as 7.6.3 |
||||
|
7.7 Spurious response |
Wanted signal power: (REFSENS + BW dependent value) Interferer signal power: -44dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged Uplink power measurement window same as 7.4 |
||||
|
7.7_1 Spurious response with 4 Rx antenna ports |
Same as 7.7 |
Same as 7.7 |
Same as 7.7 |
||||
|
7.7A.1 Spurious response for CA (intra band contiguous DL CA and UL CA) |
Wanted signal power: (REFSENS + CA BW Class specific value) Interferer signal power: -44dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
Same as 7.7 |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged Uplink power measurement window same as 7.4A.1 |
||||
|
7.7A.2 Spurious response for CA (intra band contiguous DL CA without UL CA) |
Same as 7.7A.1 |
Same as 7.7A.1 |
Same as 7.7A.1 |
||||
|
7.7A.3 Spurious response for CA (inter band DL CA without UL CA) |
Same as 7.7A.1 |
Same as 7.7A.1 |
Same as 7.7A.1 |
||||
|
7.7A.4 Spurious response for CA (intra-band non-contiguous DL CA without UL CA) |
Same as 7.7A.1 |
Same as 7.7A.1 |
Same as 7.7A.1 |
||||
|
7.7A.5 Spurious response for 3DL CA |
Same as 7.7A.1 |
Same as 7.7A.1 |
Same as 7.7A.1 |
||||
|
7.7A.7 Spurious response for 4DL CA |
Same as 7.7A.1 |
Same as 7.7A.1 |
Same as 7.7A.1 |
||||
|
7.7A.8 Spurious response for 5DL CA |
Same as 7.7A.1 |
Same as 7.7A.1 |
Same as 7.7A.1 |
||||
|
7.7A.9 Spurious response for 6DL CA |
Same as 7.7A.1 |
Same as 7.7A.1 |
Same as 7.7A.1 |
||||
|
7.7A.10 Spurious response for 7DL CA |
Same as 7.7A.1 |
Same as 7.7A.1 |
Same as 7.7A.1 |
||||
|
7.7B Spurious response for UL-MIMO |
Same as 7.7 |
Same as 7.7 |
Same as 7.7 Uplink power measurement window applies to overall UL power, which is the linear sum of the output powers over all Tx antenna connectors |
||||
|
7.7D.1 Spurious response for ProSe Direct Discovery |
Signal levels as defined in minimum requirements T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.7D.2 Spurious response for ProSe Direct Communication |
Signal levels as defined in minimum requirements T-put limit = 95% of maximum for the Ref Meas channel |
Same as 7.7D.1 |
Same as 7.7D.1 |
||||
|
7.7E Spurious response for UE category 0 |
Same as 7.7 |
Same as 7.7 |
Same as 7.7 |
||||
|
7.7EA Spurious response for UE category M1 |
Same as 7.7 |
Same as 7.7 |
Same as 7.7 |
||||
|
7.7EB Spurious response for UE category 1bis |
Same as 7.7 |
Same as 7.7 |
Same as 7.7 |
||||
|
7.7EC Spurious response for UE category M2 |
Same as 7.7 |
Same as 7.7 |
Same as 7.7 |
||||
|
7.7F Spurious response for category NB1 |
Wanted signal power: (REFSENS + 6 dB) Interferer signal power: -44dBm T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.7G.1 Spurious response for V2X Communication / Non-concurrent with E-UTRA uplink transmissions |
Wanted signal power: (REFSENS + BW dependent value) Interferer signal power: -44dBm T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.7G.2 Spurious response for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions |
Wanted signal power: (REFSENS + BW dependent value) Interferer signal power: -44dBm T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT Interferer signal power unchanged T-put limit unchanged |
||||
|
7.7G.3 Spurious response for V2X Communication / Intra-band contiguous multi-carrier operation |
Same as 7.7G.1 |
Same as 7.7G.1 |
Same as 7.7G.1 |
||||
|
7.8.1 Wide band intermodulation |
Wanted signal power: For 1.4 MHz BW: (REFSENS + 12 dB) For 3 MHz BW: (REFSENS + 8 dB) For 5 MHz and 10MHz BW: (REFSENS + 6 dB) For 15 MHz BW: (REFSENS + 7 dB) For 20 MHz BW: (REFSENS + 9 dB) CW Interferer power, all BWs: -46 dBm Modulated Interferer power:, all BWs: -46 dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Wanted signal power +TT CW Interferer signal power unchanged Modulated Interferer signal power unchanged T-put limit unchanged Uplink power measurement window same as 7.4 |
||||
|
7.8.1_1 Wide band Intermodulation with 4 Rx antenna ports |
Same as 7.8.1 |
Same as 7.8.1 |
Same as 7.8.1 |
||||
|
7.8.1A.1 Wideband intermodulation for CA (intra band contiguous DL CA and UL CA) |
Wanted signal power: (REFSENS + CA BW Class specific value) CW Interferer power, all BWs: -46 dBm Modulated Interferer power:, all BWs: -46 dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power |
0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Wanted signal power +TT CW Interferer signal power unchanged Modulated Interferer signal power unchanged T-put limit unchanged Uplink power measurement window same as 7.4 A.1 |
||||
|
7.8.1A.2 Wideband intermodulation for CA (intra band contiguous DL CA without UL CA) |
Same as 7.8.1A.1 |
Same as 7.8.1A.1 |
Same as 7.8.1A.1 |
||||
|
7.8.1A.3 Wideband intermodulation for CA (inter band DL CA without UL CA) |
Same as 7.8.1A.1 |
Same as 7.8.1A.1 |
Same as 7.8.1A.1 |
||||
|
7.8.1A.4 Wideband intermodulation for CA (intra band non-contiguous DL CA without UL CA) |
Same as 7.8.1A.1 |
Same as 7.8.1A.1 |
Same as 7.8.1A.1 |
||||
|
7.8.1A.5 Wideband intermodulation for 3DL CA |
Same as 7.8.1A.1 |
Same as 7.8.1A.1 |
Same as 7.8.1A.1 |
||||
|
7.8.1A.7 Wideband intermodulation for 4 DL CA |
Same as 7.8.1A.1 |
Same as 7.8.1A.1 |
Same as 7.8.1A.1 |
||||
|
7.8.1A.8 Wideband intermodulation for 5 DL CA |
Same as 7.8.1A.1 |
Same as 7.8.1A.1 |
Same as 7.8.1A.1 |
||||
|
7.8.1A.9 Wideband intermodulation for 6 DL CA |
Same as 7.8.1A.1 |
Same as 7.8.1A.1 |
Same as 7.8.1A.1 |
||||
|
7.8.1B Wide band intermodulation for UL-MIMO |
Same as 7.8.1 |
Same as 7.8.1 |
Same as 7.8.1 Uplink power measurement window applies to overall UL power, which is the linear sum of the output powers over all Tx antenna connectors |
||||
|
7.8.1D.1 Wide band Intermodulation for ProSe Direct Discovery |
Signal levels as defined in minimum requirements T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power + TT CW Interferer signal power unchanged Modulated Interferer signal power unchanged T-put limit unchanged |
||||
|
7.8.1D.2 Wide band Intermodulation for ProSe Direct Communication |
Signal levels as defined in minimum requirements T-put limit = 95% of maximum for the Ref Meas channel |
Same as 7.8.1D.1 |
Same as 7.8.1D.1 |
||||
|
7.8.1E Wide band intermodulation for UE category 0 |
Same as 7.8.1 |
Same as 7.8.1 |
Same as 7.8.1 |
||||
|
7.8.1EA Wide band Intermodulation for UE category M1 |
Same as 7.8.1 |
Same as 7.8.1 |
Same as 7.8.1 |
||||
|
7.8.1EB Wide band Intermodulation for UE category 1bis |
Same as 7.8.1 |
Same as 7.8.1 |
Same as 7.8.1 |
||||
|
7.8.1EC Wide band Intermodulation for UE category M2 |
Same as 7.8.1 |
Same as 7.8.1 |
Same as 7.8.1 |
||||
|
7.8.1F Wide band intermodulation for category NB1 |
Wanted signal power: (REFSENS + 6 dB) CW Interferer power: -46 dBm E-UTRA Interferer power: -46 dBm T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power +TT CW Interferer signal power unchanged Modulated Interferer signal power unchanged T-put limit unchanged |
||||
|
7.8.1G.1 Wide band Intermodulation for V2X Communication / Non-concurrent with E-UTRA uplink transmissions |
Wanted signal power: For 10MHz BW: (REFSENS + 6 dB) For 20 MHz BW: (REFSENS + 9 dB) CW Interferer power, all BWs: -46 dBm Modulated Interferer power:, all BWs: -46 dBm T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power +TT CW Interferer signal power unchanged Modulated Interferer signal power unchanged T-put limit unchanged |
||||
|
7.8.1G.2 Wide band Intermodulation for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions |
Wanted signal power on E-UTRA channel: For 1.4 MHz BW: (REFSENS + 12 dB) For 3 MHz BW: (REFSENS + 8 dB) For 5 MHz and 10MHz BW: (REFSENS + 6 dB) For 15 MHz BW: (REFSENS + 7 dB) For 20 MHz BW: (REFSENS + 9 dB) Wanted signal power on V2X Channel: For 10MHz BW: (REFSENS + 6 dB) For 20 MHz BW: (REFSENS + 9 dB) CW Interferer power, all BWs: -46 dBm Modulated Interferer power:, all BWs: -46 dBm T-put limit = 95% of maximum for the Ref Meas channel Uplink power on E-UTRA channel |
0 dB f ≤ 3.0GHz 0dB, -3.4dB 3.0GHz < f ≤ 4.2GHz 0dB, -4.0dB |
Formula: Wanted signal power +TT CW Interferer signal power unchanged Modulated Interferer signal power unchanged T-put limit unchanged Uplink power measurement window same as 7.8.1 |
||||
|
7.8.1G.3 Wide band Intermodulation for V2X Communication / Intra-band contiguous multi-carrier operation |
Wanted signal power: REFSENS + V2X Bandwidth Class specific value CW Interferer power, all BWs: -46 dBm Modulated Interferer power:, all BWs: -46 dBm T-put limit = 95% of maximum for the Ref Meas channel |
0 dB |
Formula: Wanted signal power +TT CW Interferer signal power unchanged Modulated Interferer signal power unchanged T-put limit unchanged |
||||
|
7.9 Spurious emissions |
30MHz ≤ f < 1GHz: -57dBm / 100kHz 1GHz ≤ f ≤ 12.75 GHz: -47dBm / 1MHz 12.75GHz ≤ f ≤ 19 GHz: -47dBm / 1MHz |
0 dB |
Formula: Minimum Requirement + TT |
||||
|
7.9_1 Spurious emissions with 4 Rx antenna ports |
Same as 7.9 |
Same as 7.9 |
Same as 7.9 |
||||
|
7.9A Spurious emissions for CA |
30MHz ≤ f < 1GHz: -57dBm / 100kHz 1GHz ≤ f ≤ 12.75 GHz: -47dBm / 1MHz |
0 dB |
Formula: Minimum Requirement + TT |
||||
|
7.9E Spurious emissions for UE category 0 |
Same as 7.9 |
Same as 7.9 |
Same as 7.9 |
||||
|
7.9EA Spurious emissions for UE category M1 |
Same as 7.9 |
Same as 7.9 |
Same as 7.9 |
||||
|
7.9EB Spurious emissions for UE category 1bis |
Same as 7.9 |
Same as 7.9 |
Same as 7.9 |
||||
|
7.9EC Spurious emissions for UE category M2 |
Same as 7.9 |
Same as 7.9 |
Same as 7.9 |
||||
|
7.9F Spurious emissions for category NB1 |
Same as 7.9 |
Same as 7.9 |
Same as 7.9 |
||||
|
7.9G.1 Spurious emissions for V2X Communication / Non-concurrent with E-UTRA uplink transmissions |
30MHz ≤ f < 1GHz: -57dBm / 100kHz 1GHz ≤ f ≤ 12.75 GHz: -47dBm / 1MHz 12.75GHz ≤ f ≤ 26 GHz: -47dBm / 1MHz |
0 dB |
Formula: Minimum Requirement + TT |