7.5A.5 Adjacent Channel Selectivity (ACS) for 3DL CA

36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification

Tools: ARFCN - Frequency Conversion for 5G NR/LTE/UMTS/GSM

7.5A.5.1 Test purpose

Adjacent channel selectivity for CA test verifies the UE’s ability to receive data with a given average throughput for a specified reference measurement channel, in the presence of an adjacent channel signal at a given frequency offset from the centre frequency of the assigned channel, under conditions of ideal propagation and no added noise.

A UE unable to meet the throughput requirement under these conditions will decrease the coverage area when other e-NodeB transmitters exist in the adjacent channel.

7.5A.5.2 Test applicability

This test case applies to all types of E-UTRA UE and forward that support 3DL with CA configurations in Table 7.1-2a.

This test case also applies to all types of E-UTRA UE release 13 and forward that support 3DL CA involving Band 46.

7.5A.5.3 Minimum conformance requirements

The Minimum conformance requirements are defined in clause 7.5A.0.

7.5A.5.4 Test description

7.5A.5.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and channel bandwidths based on E-UTRA CA configurations specified in tables of 5.4.2A.1 as applicable. All of these configurations shall be tested with applicable test parameters for each CA Configuration, and are shown in tables 7.5A.5.4.1-1 to 7.5A.5.4.1-2. The details of the uplink and downlink reference measurement channels (RMCs) are specified in Annexes A.2 and A.3 respectively. The details of the OCNG patterns used are specified in Annex A.5. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 7.5A.5.4.1-1: Test Configuration Table

Initial Conditions

Test Environment as specified in TS 36.508[7] subclause 4.1

Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes.

For test frequencies refer to “Range” columns. For mapping within Band refer to “CC” columns

Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.

Refer to “PCC NRB” and “SCCs NRB” columns

Network signalling value

NS_01 by default

Test Parameters for CA Configurations

PCC

SCC1

SCC2

Band

Range

NRB

Band

Range

NRB

Band

Range

NRB

UL MOD

DL MOD

ULalloc (Note 2,3)

DLalloc

UL MOD

DL MOD

ULalloc

DLalloc

UL MOD

DL MOD

ULalloc

DLalloc

Default Test Settings for a CA_XD Configuration (Intra-band contiguous)

Mid/CC1

REFSENS

All RBs

Mid/CC2

N/A

All RBs

Mid/CC3

N/A

All RBs

QPSK

Lowest N_{RB_agg}

N/A

QPSK

Lowest N_{RB_agg}

N/A

QPSK

Lowest N_{RB_agg}

Mid/CC1

REFSENS

All RBs

Mid/CC2

N/A

All RBs

Mid/CC3

N/A

All RBs

QPSK

Highest N_{RB_agg}

N/A

QPSK

Highest N_{RB_agg}

N/A

QPSK

Highest N_{RB_agg}

Default Test Settings for a CA_XA-YA-ZA Configuration (Inter-band)

Mid

REFSENS

All RBs

Mid

N/A

All RBs

Mid

N/A

All RBs

QPSK

Highest N_RB

N/A

QPSK

Highest N_RB

N/A

QPSK

Highest N_RB

Mid

REFSENS

All RBs

Mid

N/A

All RBs

Mid

N/A

All RBs

QPSK

Highest N_RB

N/A

QPSK

Highest N_RB

N/A

QPSK

Highest N_RB

Mid

REFSENS

All RBs

Mid

N/A

All RBs

Mid

N/A

All RBs

QPSK

Highest N_RB

N/A

QPSK

Highest N_RB

N/A

QPSK

Highest N_RB

Test Settings for CA_1A-18A-28A Configuration

Low

50@0

All RBs

Low

N/A

All RBs

Mid

N/A

All RBs

QPSK

N/A

QPSK

N/A

QPSK

Low

75@0

All RBs

Low

N/A

All RBs

Mid

N/A

All RBs

QPSK

N/A

QPSK

N/A

QPSK

Low

100@0

All RBs

Low

N/A

All RBs

Mid

N/A

All RBs

QPSK

100

N/A

QPSK

N/A

QPSK

Low

100@0

All RBs

Mid

N/A

All RBs

High

N/A

All RBs

QPSK

100

N/A

QPSK

N/A

QPSK

Low

25@25

All RBs

Low

N/A

All RBs

Mid

N/A

All RBs

QPSK

N/A

QPSK

N/A

QPSK

Low

25@25

All RBs

Low

N/A

All RBs

Mid

N/A

All RBs

QPSK

N/A

QPSK

N/A

QPSK

Low

25@25

All RBs

Low

N/A

All RBs

Mid

N/A

All RBs

QPSK

N/A

QPSK

100

N/A

QPSK

Mid

25@50

All RBs

Low

N/A

All RBs

High

N/A

All RBs

QPSK

N/A

QPSK

100

N/A

QPSK

Mid

25@50

All RBs

Low

N/A

All RBs

High

N/A

All RBs

QPSK

N/A

QPSK

100

N/A

QPSK

High

25@0

All RBs

Low

N/A

All RBs

Mid

N/A

All RBs

QPSK

N/A

QPSK

100

N/A

QPSK

Mid

25@25

All RBs

Low

N/A

All RBs

Low

N/A

All RBs

QPSK

N/A

QPSK

100

N/A

QPSK

High

25@25

All RBs

High

N/A

All RBs

Mid

N/A

All RBs

QPSK

N/A

QPSK

100

N/A

QPSK

Default Test Settings for CA_XB-YA and CA_XC-YA Configuration (Intra-band contiguous + Inter-band)

Mid/CC1

REFSENS

All RBs

Mid/CC2

N/A

All RBs

Mid

N/A

All RBs

QPSK

Highest N_{RB_agg}

N/A

QPSK

Highest N_{RB_agg}

N/A

QPSK

Highest N_RB

Mid/CC1

REFSENS

All RBs

Mid/CC2

N/A

All RBs

Mid

N/A

All RBs

QPSK

Lowest N_{RB_agg}

N/A

QPSK

Lowest N_{RB_agg}

N/A

QPSK

Highest N_RB

Mid

REFSENS

All RBs

Mid/CC1

N/A

All RBs

Mid/CC2

N/A

All RBs

QPSK

Highest N_RB

N/A

QPSK

Highest N_{RB_agg}

N/A

QPSK

Highest N_{RB_agg}

Mid

REFSENS

All RBs

Mid/CC1

N/A

All RBs

Mid/CC2

N/A

All RBs

QPSK

Highest N_RB

N/A

QPSK

Lowest N_{RB_agg}

N/A

QPSK

Lowest N_{RB_agg}

Default Test Settings for CA_XA-YB and CA_XA-YC Configuration (Intra-band contiguous + Inter-band)

Mid/CC1

REFSENS

All RBs

Mid/CC2

N/A

All RBs

Mid

N/A

All RBs

QPSK

Highest N_{RB_agg}

N/A

QPSK

Highest N_{RB_agg}

N/A

QPSK

Highest N_RB

Mid/CC1

REFSENS

All RBs

Mid/CC2

N/A

All RBs

Mid

N/A

All RBs

QPSK

Lowest N_{RB_agg}

N/A

QPSK

Lowest N_{RB_agg}

N/A

QPSK

Highest N_RB

Mid

REFSENS

All RBs

Mid/CC1

N/A

All RBs

Mid/CC2

N/A

All RBs

QPSK

Highest N_RB

N/A

QPSK

Highest N_{RB_agg}

N/A

QPSK

Highest N_{RB_agg}

Mid

REFSENS

All RBs

Mid/CC1

N/A

All RBs

Mid/CC2

N/A

All RBs

QPSK

Highest N_RB

N/A

QPSK

Lowest N_{RB_agg}

N/A

QPSK

Lowest N_{RB_agg}

Note 1: CA Configuration Test CC Combination test settings are checked separately for each CA Configuration, The applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1.

Note 2: Use CA Configuration – specific test points if present in the table, otherwise use Default Test Settings test points.

Note 3: Inter-band & Intra-band contiguous + Inter-band: If, according to the UE declared capability, UE does not support UL in an individual band within the CA Configuration, test points with that individual band as PCC are not applicable.

Note 4: Intra-band contiguous: X corresponds to the band in the CA Configuration. E.g. for CA_41D, X=41

Note 5: Inter-band: X,Y,Z correspond to the 1^st, 2^nd and 3^rd band in the CA Configuration. E.g. for CA_1A-3A-19A, X=1, Y=3, Z=19

Note 6: Intra-band contiguous + Inter-band: X,Y correspond to the different bands in the CA Configuration. E.g. for CA_1C-3A, X=1 and Y=3

Note 7: REFSENS refers to the PCC band’s and PCC N_RB ‘s single carrier Uplink RB allocation for reference sensitivity according to table 7.3.5-2.

Note 8: Intra-band contiguous: If in the CA Configuration UE supports multiple CC Combinations with the same N_{RB_agg}, choose for testing the Combination with maximum N_{RB_PCC} and then select maximum N_{RB_SCC1}for the chosen N_{RB_PCC}.

Note 9: Intra-band contiguous + Inter-band: If in the CA Configuration UE supports multiple CC Combinations with the same N_{RB_agg}, choose the Combination with N_{RB_PCC} = N_{RB_SCC1}for testing. If no such combination is supported, choose Combination with maximum N_{RB_PCC} for testing.

Note 10: The orders and numbering of SCCs in this table does not imply any order in test implementation of SCCs.

Note 11: ID/test points that result in no refsens requirement shall be skipped.

Table 7.5A.5.4.1-2: Test Configuration Table W_gap

Initial Conditions

Test Environment as specified in TS 36.508[7] subclause 4.1

Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes.

For test frequencies refer to “Range” columns. For mapping within Band refer to “CC” columns

Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.

Highest N_RB

Network signalling value

NS_01 by default

Test Parameters for CA Configurations

PCC

W_gap[MHz]

SCC1

W_gap[MHz]

SCC2

Band

Range

NRB

Band

Range

NRB

Band

Range

NRB

UL MOD

DL MOD

ULalloc

(Note 2,3,4)

alloc

UL MOD

DL MOD

alloc

UL MOD

DL MOD

alloc

Default Test Settings for CA_XA-XA-YA Configurations (Intra-band non-contiguous + Inter-band)

CC2

REFSENS

All RBs

Max

CC1

N/A

All RBs

–

Mid

N/A

All RBs

QPSK

Highest N_{RB_agg}

N/A

QPSK

Highest N_{RB_agg}

N/A

QPSK

Highest N_RB

Mid

REFSENS

All RBs

–

CC2

N/A

All RBs

Max

CC1

N/A

All RBs

QPSK

Highest N_RB

N/A

QPSK

Highest N_{RB_agg}

N/A

QPSK

Highest N_{RB_agg}

Default Test Settings for CA_XA-YA-YA Configurations (Intra-band non-contiguous + Inter-band)

CC2

REFSENS

All RBs

Max

CC1

N/A

All RBs

–

Mid

N/A

All RBs

QPSK

Highest N_{RB_agg}

N/A

QPSK

Highest N_{RB_agg}

N/A

QPSK

Highest N_RB

Mid

REFSENS

All RBs

–

CC2

N/A

All RBs

Max

CC1

N/A

All RBs

QPSK

Highest N_RB

N/A

QPSK

Highest N_{RB_agg}

N/A

QPSK

Highest N_{RB_agg}

Test Settings for CA_29A-66A-66A Configuration (Intra-band non-contiguous + Inter-band)

CC1

100@0

All RBs

CC2

N/A

All RBs

–

Mid

N/A

All RBs

QPSK

100

N/A

QPSK

100

N/A

QPSK

Test Settings for a CA_41C-41A Configuration (Intra-band non-contiguous + Intra-band contiguous)

CC3

100@0

All RBs

134.2

CC2

N/A

All RBs

–

CC1

N/A

All RBs

QPSK

100

N/A

QPSK

100

N/A

QPSK

100

Test Settings for a CA_41A-41C Configuration (Intra-band non-contiguous + Intra-band contiguous)

CC3

100@0

All RBs

–

CC2

N/A

All RBs

134.2

CC1

N/A

All RBs

QPSK

100

N/A

QPSK

100

N/A

QPSK

100

Group Test Settings for CA_66A-66A-XA or CA_XA-66A-66A Configurations (Intra-band non-contiguous + Inter-band)

CC1

100@0

All RBs

CC2

N/A

All RBs

–

Mid

N/A

All RBs

QPSK

100

N/A

QPSK

100

N/A

QPSK

Highest NRB

Mid

REFSENS

All RBs

–

CC1

N/A

All RBs

CC2

N/A

All RBs

QPSK

Highest NRB

N/A

QPSK

100

N/A

QPSK

100

Test Settings for a CA_66A-66C Configuration (Intra-band non-contiguous + Intra-band contiguous)

CC1

100@0

All RBs

30.2

CC2

N/A

All RBs

–

CC3

N/A

All RBs

QPSK

100

N/A

QPSK

100

N/A

QPSK

100

Test Settings for a CA_66A-66A-66A Configuration (Intra-band non-contiguous)

CC1

100@0

All RBs

CC2

N/A

All RBs

CC3

N/A

All RBs

QPSK

100

N/A

QPSK

100

N/A

QPSK

100

Note 1: CA Configuration Test CC Combination test settings are checked separately for each CA Configuration.

Note 2: Intra-band non-contiguous + Inter-band: Use CA Configuration – specific test points if present in the table. Otherwise use test points from matching Group Test Settings, if present in the table. Otherwise use Default Test Settings test points.

Note 3: Intra-band non-contiguous + Intra-band contiguous: Use CA Configuration – specific test points if present in the table, otherwise use Default Test Settings test points.

Note 4: If, according to the UE declared capability, UE does not support UL in an individual band within the CA Configuration, test points with that individual band as PCC are not applicable.

Note 5: Intra-band non-contiguous + Inter-band: X and Y correspond to the different bands in the CA Configuration. E.g. for CA_2A-2A-5A,X=2,Y=5

Note 6: Intra-band non-contiguous + Intra-band contiguous: X corresponds to the band of the CA Configuration. E.g. for CA_41C-41A,X=41.

Note 7: Intra-band non-contiguous + Inter-band: REFSENS refers to the PCC band’s and PCC N_RB ‘s single carrier Uplink RB allocation for reference sensitivity according to table 7.3.5-2.

Note 8: Intra-band non-contiguous + Intra-band contiguous: REFSENS refers to the PCC band’s and PCC N_RB ‘s single carrier Uplink RB allocation for reference sensitivity according to table 7.3.5-2.

Note 9: Intra-band non-contiguous + Intra-band contiguous: If in the CA Configuration UE supports multiple CC Combinations with the same N_{RB_agg}, choose the Combination with N_{RB_CC1} = N_{RB_CC2}for testing. If no such combination is supported, choose Combination with maximum N_{RB_CC1} for testing.

Note 10: The orders and numbering of SCCs in this table does not imply any order in test implementation of SCCs.

Note 11: ID/test points that result in no refsens requirement shall be skipped.

1. Connect the SS to the UE antenna connectors as shown in TS 36.508 [7] Annex A, Figure A.58 if the UE supports 2 Rx antennas or Figure A.82 if the UE supports 4 Rx antennas in the band.

2. The parameter settings for the cell are set up according to TS 36.508 [7] clause 4.4.3.

3. Downlink signals for PCC are initially set up according to Annex C.0, C.1 and C.3.1, and uplink signals according to Annex H.1 and H.3.1

4. The UL and DL Reference Measurement channels are set according to Tables 7.5A.5.4.1-1 to 7.5A.5.4.1-2.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 7.5A.5.4.3.

7.5A.5.4.2 Test procedure

1. Configure SCCs according to Annex C.0, C.1 and Annex C.3.1 for all downlink physical channels.

2. The SS shall configure SCCs as per TS 36.508 [7] clause 5.2A.4. Message contents are defined in clause 7.5A.5.4.3

3. SS activates SCCs by sending the activation MAC-CE (Refer to TS 36.321 [13] clauses 5.13 and 6.1.3.8). Wait for at least 2 seconds (Refer to TS 36.133 [4], clause 8.3.3.2).

4. SS transmits PDSCH via PDCCH DCI format 1A for C_RNTI to transmit the DL RMC according to Tables 7.5A.5.4.1-1 to 7.5A.5.4.1-5 as appropriate on PCC and SCCs. The SS sends downlink MAC padding bits on the DL RMC.

5. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Tables 7.5A.5.4.1-1 to 7.5A.5.4.1-2 as appropriate on PCC. Since the UE has no payload and no loopback data to send, the UE sends uplink MAC padding bits on the UL RMC.

6. Set the Downlink signal level for PCC and SCCs to the value defined for Case 1 in Table 7.5A.5.4.2-1according to the type of CA. Send Uplink power control commands to the UE (less or equal to 1dB step size should be used), to ensure that the PCC output power is within +0dB, -3.4 dB of the target level for carrier frequency f ≤ 3.0GHzor within +0dB, -4 dB of the target level for carrier frequency 3.0GHz < f ≤ 4.2GHz, for at least the duration of the Throughput measurement.

7. Set the Interferer signal level to the value defined for Case 1 in Table 7.5A.5.4.2-1, according to the type of CA, with frequency below the measured carrier(s) according to table 7.5A.5.4.2-1, using a modulated interferer bandwidth as defined in Annex D of the present document. The interferer frequencies are adjusted in analogy with table 7.5A.1.4.2-1.

8. Measure the average throughput for the carrier(s) indicated in table 7.5A.5.4.2-1 for a duration sufficient to achieve statistical significance according to Annex G.2A.

9. Repeat steps from 6 to 8, using an interfering signal above the measured carrier(s) according to table 7.5A.5.4.2-1.

10. Set the Downlink signal level for PCC and SCCs to the value defined for Case 2 in Table 7.5A.5.4.2-1, according to the type of CA. Send Uplink power control commands to the UE (less or equal to 1dB step size should be used), to ensure that the PCC output power is within +0dB, -3.4 dB of the target level for carrier frequency f ≤ 3.0GHz,
or within +0dB, -4 dB of the target level for carrier frequency 3.0GHz < f ≤ 4.2GHz, for at least the duration of the Throughput measurement.

11. Set the Interferer signal level to the value defined for Case 2 in Table 7.5A.5.4.2-1, according to the type of CA, with frequency below the measured carrier(s) according to table 7.5A.5.4.2-1, using a modulated interferer bandwidth as defined in Annex D of the present document. The interferer frequencies are adjusted in analogy with table 7.5A.1.4.2-1.

12. Measure the average throughput for the carrier(s) indicated in table 7.5A.5.4.2-1 for a duration sufficient to achieve statistical significance according to Annex G.2A.

13. Repeat steps from 10 to 12, using an interfering signal above the measured carrier(s) according to table 7.5A.5.4.2-1.

14. Repeat steps 6 to 13 for component carriers listed in Table 7.5A.5.4.2-1.

Table 7.5A.5.4.2-1: Test repetition and measurement configuration

CA configuration	ID (Note 1)	Throughput measured on (Note 3)	Table with test parameters to select (Note 2)
Intra-band contiguous	1	PCC, SCC1, SCC2	7.5A.5.5-2 7.5A.5.5-3
	2
Inter-band	1	SCC1	7.5A.5.5-0e 7.5A.5.5-0f 7.5A.5.5-5 7.5A.5.5-6
		SCC2
	2	SCC1
		SCC2
	3	SCC1
		SCC2
Intra-band contiguous + Inter-band	1	SCC2	7.5A.5.5-0e 7.5A.5.5-0f 7.5A.5.5-5 7.5A.5.5-6
	2
	3	SCC1, SCC2	7.5A.5.5-0b 7.5A.5.5-0c 7.5A.5.5-2 7.5A.5.5-3
	4
Intra-band non-contiguous + Inter-band	1	SCC2	7.5A.5.5-0e 7.5A.5.5-0f 7.5A.5.5-5 7.5A.5.5-6
	2	SCC1
		SCC2
Intra-band non-contiguous + Intra-band contiguous	1	PCC	7.5A.5.5-5 7.5A.5.5-6
		SCC1, SCC2	7.5A.5.5-0b 7.5A.5.5-0c 7.5A.5.5-2 7.5A.5.5-3
	2	PCC, SCC1	7.5A.5.5-0b 7.5A.5.5-0c 7.5A.5.5-2 7.5A.5.5-3
		SCC2	7.5A.5.5-5 7.5A.5.5-6
Intra-band non-contiguous	1	PCC, SCC1, SCC2	7.5A.5.5-5 7.5A.5.5-6
Note 1: Test point ID for the particular CA configuration as defined in section 7.5A.5.4.1. Note 2: The reference for the placement of the interferer signals is the centre frequency of the carrier closest to the interferer among the carriers throughput is measured on. Note 3: Where there are multiple rows for a single Test point ID, the test is repeated for each row.

7.5A.5.4.3 Message contents

The message contents are the same as in clause 7.5.4.3 for without UL CA.

The message contents are the same as in clause 7.5A.1.4.3 for UL CA.

7.5A.5.5 Test requirement

The throughput measurement of each carrier derived in test procedure shall be ≥ 95% of the maximum throughput of the reference measurement channels as specified in Annex A.3.2 with parameters specified in Tables below, according to the type of CA.

The test requirements do not apply when the interfering signal overlaps with the channel bandwidth of any downlink CC.

Table 7.5A.5.5-0a: Adjacent channel selectivity for 3DL CA (band 46)

E-UTRA band	Rx Parameter	Units	CA Bandwidth Class
E-UTRA band	Rx Parameter	Units	B	C	D	E	F
46	ACS	dB		24	22.2

Table 7.5A.5.5-0b: Test parameters for Adjacent channel selectivity for 3DL CA (band 46), Case 1

E-UTRA Band	Rx Parameter	Units	CA Bandwidth Class
E-UTRA Band	Rx Parameter	Units	B	C	D	E	F
46	Pw in Transmission Bandwidth Configuration, per CC			REFSENS + 14 dB	REFSENS + 14 dB
	PInterferer	dBm		Aggregated power + 22.5 dB	Aggregated power + 20.7 dB
	BW_Interferer	MHz		20	20
	F_{Interferer (offset)}	MHz		10 + F_offset / -10 – F_offset	10 + F_offset / -10 – F_offset
NOTE 1*: In a band capable of uplink operation, the transmitter shall be set to 4dB below P_{CMAX_L,c}or PCMAX_L as defined in subclause 6.2.5A. NOTE 2: The interferer consists of the Reference measurement channel specified in Annex A.3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD/FS3 as described in Annex A.5.1.1/A.5.2.1/A.5.3.1 and set-up according to Annex C.3.1. NOTE 3: The F_interferer (offset) is the frequency separation of the centre frequency of the carrier closest to the interferer and the centre frequency of the adjacent channel interferer and shall be further adjusted to MHz to be offset from the sub-carrier raster.

Table 7.5A.5.5-0c: Test parameters for Adjacent channel selectivity for 3DL CA (band46), Case 2

E-UTRA band	Rx Parameter	Units	CA Bandwidth Class
E-UTRA band	Rx Parameter	Units	B	C	D	E	F
46	Pw in Transmission Bandwidth Configuration, per CC	dBm		-47.5 +10log10(_NRB,c/N_{RB agg})	-45.7 +10log10(_NRB,c/N_{RB agg})
	P_Interferer	dBm	-25
	BW_Interferer	MHz		20	20
	F_Interferer (offset)	MHz		10 + F_offset / -10 – F_offset	10 + F_offset / -10 – F_offset
NOTE 1: In a band capable of uplink operation, the transmitter shall be set to 24dB below PCMAX_L,c or PCMAX_L as defined in subclause 6.2.5A. NOTE 2: The interferer consists of the Reference measurement channel specified in Annex 3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD/FS3 as described in Annex A.5.1.1/A.5.2.1/A.5.3.1 and set-up according to Annex C.3.1. NOTE 3: The F_interferer (offset) is the frequency separation of the centre frequency of the carrier closest to the interferer and the centre frequency of the adjacent channel interferer and shall be further adjusted to MHz to be offset from the sub-carrier raster.

Table 7.5A.5.5-0d: Adjacent channel selectivity for 3DL CA (band 46)

E-UTRA band	Rx Parameter	Units	Channel bandwidth
E-UTRA band	Rx Parameter	Units	1.4 MHz	3 MHz	5 MHz	10 MHz	15 MHz	20 MHz
46	ACS	dB				33		27

Table 7.5A.5.5-0e: Test parameters for Adjacent channel selectivity for 3DL CA
(band 46), Case 1

E-UTRA Band	Rx Parameter	Units	Channel bandwidth
E-UTRA Band	Rx Parameter	Units	1.4 MHz	3 MHz	5 MHz	10 MHz	15 MHz	20 MHz
46	Power in Transmission Bandwidth Configuration	dBm	REFSENS + 14 dB
	P_Interferer	dBm				REFSENS +45.5dB		REFSENS +39.5dB
	BW_Interferer	MHz				20		20
	F_Interferer (offset)	MHz				15+0.0075 /-15-0.0075		20+0.0025 /-20-0.0025
NOTE 1: In a band capable of uplink operation, the transmitter shall be set to 4dB below PCMAX_L at the minimum uplink configuration specified in Table 7.3.3-2 with PCMAX_L as defined in subclause 6.2.5. NOTE 2: The interferer consists of the Reference measurement channel specified in Annex A.3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD/FS3 as described in Annex A.5.1.1/A.5.2.1/A.5.3.1 and set-up according to Annex C.3.1.

Table 7.5A.5.5-0f: Test parameters for Adjacent channel selectivity for 3DL CA
(band 46), Case 2

E-UTRA band	Rx Parameter	Units	Channel bandwidth
E-UTRA band	Rx Parameter	Units	1.4 MHz	3 MHz	5 MHz	10 MHz	15 MHz	20 MHz
46	Power in Transmission Bandwidth Configuration	dBm				-56.5		-50.5
	P_Interferer	dBm	-25
	BW_Interferer	MHz				20		20
	F_Interferer (offset)	MHz				15+0.0075 /-15-0.0075		20+0.0025 /-20-0.0025
NOTE 1: In a band capable of uplink operation, the transmitter shall be set to 24dB below PCMAX_L at the minimum uplink configuration specified in Table 7.3.3-2 with PCMAX_L as defined in subclause 6.2.5. NOTE 2: The interferer consists of the Reference measurement channel specified in Annex A.3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD/FS3 as described in Annex A.5.1.1/A.5.2.1/A.5.3.1 and set-up according to Annex C.3.1.

Table 7.5A.5.5-1: Adjacent channel selectivity for 3DL CA (Intra-band contiguous)

		CA Bandwidth Class
Rx Parameter	Units	B	C	D	E	F
ACS	dB	27	24	22.2

Table 7.5A.5.5-2: Test parameters for Adjacent channel selectivity, Case 1, 3DL CA (Intra-band contiguous)

Rx Parameter	Units	CA Bandwidth Class
Rx Parameter	Units	B	C	D	E	F
Pw in Transmission Bandwidth Configuration, per CC		REFSENS + 14 dB	REFSENS + 14 dB	REFSENS + 14 dB
P_Interferer	dBm	Aggregated power + 22.5 dB	Aggregated power + 22.5 dB	Aggregated power + 20.7 dB
BW_Interferer	MHz	5	5	5
F_Interferer (offset)	MHz	2.5 + F_offset / -2.5 – F_offset	2.5 + F_offset / -2.5 – F_offset	2.5 + F_offset / -2.5 – F_offset
NOTE 1: The transmitter shall be set to 4dB below P_{CMAX_L}or PCMAX_L_{_CA} as defined in subclause 6.2.5 for one uplink carrier. NOTE 2: The interferer consists of the Reference measurement channel specified in Annex A.3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD as described in Annex A.5.1.1/A.5.2.1 and set-up according to Annex C.3.1 NOTE 3: The F_interferer (offset) is the frequency separation of the centre frequency of the carrier closest to the interferer and the centre frequency of the adjacent channel interferer and shall be further adjusted to MHz to be offset from the sub-carrier raster.

Table 7.5A.5.5-3: Test parameters for Adjacent channel selectivity, Case 2, 3DL CA (Intra-band contiguous)

Rx Parameter	Units	CA Bandwidth Class
Rx Parameter	Units	B	C	D	E	F
Pw in Transmission Bandwidth Configuration, per CC	dBm	-50.5 +10log₁₀(N_RB,c/ N_{RB agg})	-47.5 +10log₁₀(N_RB,c/N_{RB agg})	-43.9 +10log10(N_RB,c/N_{RB agg})
P_Interferer	dBm	-25
BW_Interferer	MHz	5	5	5
F_Interferer (offset)	MHz	2.5+ F_offset / -2.5- F_offset	2.5+ F_offset / -2.5- F_offset	2.5+ F_offset / -2.5- F_offset
NOTE 1: The transmitter shall be set to 24dB below PCMAX_L or PCMAX_L_CA as defined in subclause 6.2.5 for one uplink carrier. NOTE 2: The interferer consists of the Reference measurement channel specified in Annex 3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD as described in Annex A.5.1.1/A.5.2.1 and set-up according to Annex C.3.1 NOTE 3: The F_interferer (offset) is the frequency separation of the centre frequency of the carrier closest to the interferer and the centre frequency of the adjacent channel interferer and shall be further adjusted to MHz to be offset from the sub-carrier raster.

Table 7.5A.5.5-4: Adjacent channel selectivity for 3DL CA (Inter-band, Intra-band non-contiguous), per CC

		Channel bandwidth
Rx Parameter	Units	1.4 MHz	3 MHz	5 MHz	10 MHz	15 MHz	20 MHz
ACS	dB	33.0	33.0	33.0	33.0	30	27

Table 7.5A.5.5-5: Test parameters for Adjacent channel selectivity for 3DL CA (Inter-band, Intra-band non-contiguous), Case 1

Rx Parameter	Units	Channel bandwidth
Rx Parameter	Units	1.4 MHz	3 MHz	5 MHz		10 MHz	15 MHz	20 MHz
Power in Transmission Bandwidth Configuration for each CC	dBm	REFSENS + 14 dB
P_Interferer	dBm	REFSENS for SCC +45.5dB	REFSENS for SCC +45.5dB		REFSENS for SCC +45.5dB	REFSENS for SCC +45.5dB	REFSENS for SCC +42.5dB	REFSENS for SCC +39.5dB
BW_Interferer	MHz	1.4	3		5	5	5	5
F_Interferer (offset)	MHz	1.4+0.0025 / -1.4-0.0025	3+0.0075 / -3-0.0075		5+0.0025 / -5-0.0025	7.5+0.0075 / -7.5-0.0075	10+0.0125 / -10-0.0125	12.5+0.0025 / -12.5-0.0025
NOTE 1: The transmitter shall be set to 4dB below PCMAX_L.at the minimum uplink configuration specified in Table 7.3.3-2 with PCMAX_L as defined in subclause 6.2.5. NOTE 2: The interferer consists of the Reference measurement channel specified in Annex A.3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD as described in Annex A.5.1.1/A.5.2.1 and set-up according to Annex C.3.1

Table 7.5A.5.5-6: Test parameters for Adjacent channel selectivity for 3DL CA (Inter-band, Intra-band non-contiguous), Case 2

Rx Parameter	Units	Channel bandwidth
Rx Parameter	Units	1.4 MHz	3 MHz	5 MHz	10 MHz	15 MHz	20 MHz
Power in Transmission Bandwidth Configuration for each CC	dBm	-56.5	-56.5	-56.5	-56.5	-53.5	-50.5
P_Interferer	dBm	-25
BW_Interferer	MHz	1.4	3	5	5	5	5
F_Interferer (offset)	MHz	1.4+0.0025 / -1.4-0.0025	3+0.0075 / -3-0.0075	5+0.0025 / -5-0.0025	7.5+0.0075 / -7.5-0.0075	10+0.0125 / -10-0.0125	12.5+0.0025 / -12.5-0.0025
NOTE 1: The transmitter shall be set to 24dB below PCMAX_L at the minimum uplink configuration specified in Table 7.3.3-2 with PCMAX_L as defined in subclause 6.2.5. NOTE 2: The interferer consists of the Reference measurement channel specified in Annex 3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD as described in Annex A.5.1.1/A.5.2.1 and set-up according to Annex C.3.1.