6.2.5E Configured UE transmitted Output Power for UE category 0
36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification
6.2.5E.1 Test purpose
Same test purpose as on clause 6.2.5.1.
6.2.5E.2 Test applicability
This test case applies to all types of E-UTRA UE release 12 and forward of UE category 0.
6.2.5E.3 Minimum conformance requirements
Same minimum conformance requirements as in clause 6.2.2.3.
6.2.5E.4 Test description
6.2.5E.4.1 Initial conditions
Same initial conditions as in clause 6.2.5.4.1 with following exceptions:
– Instead of Table 6.2.5.4.1-1 🡪 use Table 6.2.5E.4.1-1.
– Connect SS to the UE antenna connectors as shown in TS 36.508 [7] Annex A Figure A.3 using only main UE Tx/Rx antenna.
Table 6.2.5E.4.1-1: Test Configuration Table
|
Initial Conditions |
|||||
|
Test Environment as specified in TS 36.508 [7] subclause 4.1 |
Normal, TL/VL, TL/VH, TH/VL, TH/VH |
||||
|
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 |
Mid range |
||||
|
Test Channel Bandwidths as specified in TS 36.508 [7] subclause 4.3.1 |
Lowest, 5MHz, Highest |
||||
|
Test Parameters for Channel Bandwidths |
|||||
|
Downlink Configuration |
Uplink Configuration |
||||
|
Ch BW |
N/A for Configured UE transmitted Output Power test case |
Mod’n |
RB allocation |
||
|
FDD and HD-FDD |
TDD |
||||
|
1.4MHz |
QPSK |
5 |
5 |
||
|
3MHz |
QPSK |
4 |
4 |
||
|
5MHz |
QPSK |
8 |
8 |
||
|
10MHz |
QPSK |
12 |
12 |
||
|
15MHz |
QPSK |
16 |
16 |
||
|
20MHz |
QPSK |
18 |
18 |
||
|
Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: For the uplink RB allocation the RBstart shall be RB #0. |
|||||
6.2.5E.4.2 Test procedure
Same test procedure as in clause 6.2.5.4.2 with following exception for HD-FDD:
– In step 3, slots with transient periods are not under test. Half-duplex guard sub frame are not under test.
6.2.5E.4.3 Message contents
Same message contents as in clause 6.2.5.4.3.
6.2.5E.5 Test requirement
The maximum output power measured shall not exceed the values specified in Table 6.2.5E.5-1.
Table 6.2.5E.5-1: PCMAX configured UE output power
|
Channel bandwidth / maximum output power |
||||||
|
1.4 MHz |
3.0 MHz |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
|
|
Measured UE output power test point 1 |
For carrier frequency f ≤ 3.0GHz: -10 dBm ± 7.7 For carrier frequency 3.0GHz < f ≤ 4.2GHz: -10 dBm ± 8.0 |
|||||
|
Measured UE output power test point 2 |
For carrier frequency f ≤ 3.0GHz: 10 dBm ± 6.7 For carrier frequency 3.0GHz < f ≤ 4.2GHz: 10 dBm ± 7.0 |
|||||
|
Measured UE output power test point 3 |
For carrier frequency f ≤ 3.0GHz: 15 dBm ± 5.7 For carrier frequency 3.0GHz < f ≤ 4.2GHz: 15 dBm ± 6.0 |
|||||
|
Note: In addition note 2 in Table 6.2.2.3-1 shall apply to the tolerances. |
||||||