6.6.3EB Spurious emission for UE category 1bis
36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification
6.6.3EB.1 Transmitter Spurious emissions for UE category 1bis
6.6.3EB.1.1 Test purpose
Same test purpose as in clause 6.6.3.1.1.
6.6.3EB.1.2 Test applicability
This test case applies to all types of E-UTRA UE release 13 and forward of UE category 1bis.
6.6.3EB.1.3 Minimum conformance requirements
Same minimum conformance requirements as in clause 6.6.3.1.3.
6.6.3EB.1.4 Test description
6.6.3EB.1.4.1 Initial conditions
Same initial conditions as in clause 6.6.3.1.4.1
– Connect SS to the UE antenna connectors as shown in TS 36.508[7] Annex A Figure A.3 using only main UE Tx/Rx antenna.
6.6.3EB.1.4.2 Test procedure
Same test procedure as in clause 6.6.3.1.4.2
6.6.3EB.1.4.3 Message contents
Message contents same clause 6.6.3.1.4.3.
6.6.3EB.1.5 Test requirement
This clause specifies the requirements for the specified E-UTRA band for Transmitter Spurious emissions requirement with frequency range as indicated in table 6.6.3EB.1.5-1.
The measured average power of spurious emission, derived in step 3, shall not exceed the described value in Table 6.6.3EB.1.5-1.
The spurious emission limits apply for the frequency ranges that are more than ΔfOOB (MHz) from the edge of the channel bandwidth shown in Table 6.6.3.1.3-1.
NOTE: For measurement conditions at the edge of each frequency range, the lowest frequency of the measurement position in each frequency range should be set at the lowest boundary of the frequency range plus MBW/2. The highest frequency of the measurement position in each frequency range should be set at the highest boundary of the frequency range minus MBW/2. MBW denotes the measurement bandwidth defined for the protected band.
Table 6.6.3EB.1.5-1: General spurious emissions test requirements
|
Frequency Range |
Maximum |
Measurement |
Notes |
|
9 kHz ≤ f < 150 kHz |
-36 dBm |
1 kHz |
|
|
150 kHz ≤ f < 30 MHz |
-36 dBm |
10 kHz |
|
|
30 MHz ≤ f < 1000 MHz |
-36 dBm |
100 kHz |
|
|
1 GHz ≤ f < 12.75 GHz |
-30 dBm |
1 MHz |
6.6.3EB.2 Spurious emission band UE co-existence for UE category 1bis
6.6.3EB.2.1 Test purpose
Same test purpose as in clause 6.6.3.2.1.
6.6.3EB.2.2 Test applicability
This test case applies to all types of E-UTRA UE release 13 and forward of UE category 1bis.
6.6.3EB.2.3 Minimum conformance requirements
Same minimum conformance requirements as in clause 6.6.3.2.3
6.6.3EB.2.4 Test description
6.6.3EB.2.4.1 Initial conditions
Same initial conditions as in clause 6.6.3.2.4.1
– Connect the SS to the UE antenna connectors as shown in TS 36.508[7] Annex A Figure A.3 using only main UE Tx/Rx antenna.
6.6.3EB.2.4.2 Test procedure
Same test procedure as in clause 6.6.3.2.4.2
6.6.3EB.2.4.3 Message contents
Message contents same as 6.6.3.2.4.3
6.6.3EB.2.5 Test requirement
Test requirements for Spurious Emissions UE Co-existence are the same as the minimum requirements and are not repeated in this section.
6.6.3EB.3 Additional spurious emissions for UE category 1bis
6.6.3EB.3.1 Test purpose
Same test purpose as in clause 6.6.3.3.1.
6.6.3EB.3.2 Test applicability
This test case applies to all types of E-UTRA UE release 13 and forward of UE category 1bis.
6.6.3EB.3.3 Minimum conformance requirements
Same minimum conformance requirements as in clause 6.6.3.3.3.
6.6.3EB.3.4 Test description
6.6.3EB.3.4.1 Initial conditions
Same initial conditions as in clause 6.6.3.3.4.1.
– Connect SS to the UE antenna connectors as shown in TS 36.508[7] Annex A Figure A.3 using only main UE Tx/Rx antenna.
6.6.3EB.3.4.2 Test procedure
Same test procedure as in clause 6.6.3.3.4.2
6.6.3EB.3.4.3 Message contents
Same message contents as in clause 6.6.3.3.4.3.
6.6.3EB.3.5 Test requirement
This clause specifies the requirements for the specified E-UTRA band for an additional spectrum emission requirement with protected bands as indicated from table 6.6.3.1.5-1 to table 6.6.3.2.5-1.
NOTE: For measurement conditions at the edge of each frequency range, the lowest frequency of the measurement position in each frequency range should be set at the lowest boundary of the frequency range plus MBW/2. The highest frequency of the measurement position in each frequency range should be set at the highest boundary of the frequency range minus MBW/2. MBW denotes the measurement bandwidth defined for the protected band.
6.6.3EB.3.5.1 Test requirement (network signalled value “NS_04”)
When "NS 04" is indicated in the cell:
– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-3 or 6.2.4_1.5-2 as appropriate, and
– the power of any UE emission shall not exceed the levels specified in Table 6.6.3EB.3.5.1-1. This requirement also applies for the frequency ranges that are less than FOOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.
Table 6.6.3EB.3.5.1-1: Additional requirements
|
Frequency band |
Channel bandwidth / Spectrum emission limit (dBm) |
Measurement bandwidth |
|
5, 10, 15, 20 MHz |
||
|
2490.5 MHz ≤ f < 2495 MHz |
-13 |
1 MHz |
|
9 kHz < f < 2490.5 MHz |
-25 |
1 MHz |
6.6.3EB.3.5.2 Test requirement (network signalled value "NS_05")
When "NS_05" is indicated in the cell:
– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-4 as appropriate,
and
the measured average power of spurious emission, derived in step 2, shall not exceed the described requirements for the corresponding Release as defined in Table 6.6.3EB.3.5.2-0. This requirement also applies for the frequency ranges that are less than ΔfOOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.
Table 6.6.3EB.3.5.2-0: Applicable requirements per UE release
|
UE Release |
Rel-10 and earlier |
Rel-11 (number 1 bit in modifiedMPRbehavior=0) |
Rel-11 (number 1 bit in modifiedMPRbehavior=1) |
Rel-12 and later |
|
ID |
1 |
2 |
3 |
4 |
|
Applicable Requirements |
Table 6.6.3.3.5.2-1 & 6.6.3.3.5.2-2 |
Table 6.6.3.3.5.2-1 & 6.6.3.3.5.2-2 |
Table 6.6.3.3.5.2-3 |
Table 6.6.3.3.5.2-3 |
Table 6.6.3EB.3.5.2-1: Additional test requirements (PHS) (Rel-11 and earlier)
|
Frequency band (MHz) |
Channel bandwidth / Spectrum emission limit (dBm) |
Measurement bandwidth |
|||
|
5 MHz |
10 MHz |
15 MHz |
20 MHz |
||
|
1884.5 f 1915.7*1 |
-41 |
-41 |
-41 |
-41 |
300 KHz |
|
Note 1: Applicable when the lower edge of the assigned E-UTRA UL channel bandwidth frequency is larger than or equal to the upper edge of PHS band (1915.7 MHz) + 4 MHz + the Channel BW assigned, where Channel BW is as defined in sub-clause 5.4.2. Additional restrictions apply for operations below this point. |
|||||
The requirements in Table 6.6.3EB.3.5.2-1 apply with the additional restrictions specified in Table 6.6.3EB.3.5.2-2 when the lower edge of the assigned E-UTRA UL channel bandwidth frequency is less than the upper edge of PHS band (1915.7 MHz) + 4 MHz + the channel BW assigned.
Table 6.6.3EB.3.5.2-2: RB restrictions for additional requirement (PHS)
|
15 MHz channel bandwidth with fc = 1932.5 MHz |
|||
|
RBstart |
0-7 |
8-66 |
67-74 |
|
LCRB |
N/A |
≤ MIN(30, 67 – RBstart) |
N/A |
|
20 MHz channel bandwidth with fc = 1930 MHz |
|||
|
RBstart |
0-23 |
24-75 |
76-99 |
|
LCRB |
N/A |
≤ MIN(24, 76 – RBstart) |
N/A |
Table 6.6.3EB.3.5.2-3: Additional test requirements (PHS) (Rel-12 and onwards)
|
Frequency band (MHz) |
Channel bandwidth / Spectrum emission limit (dBm) |
Measurement bandwidth |
|||
|
5 MHz |
10 MHz |
15 MHz |
20 MHz |
||
|
1884.5 f 1915.7 |
-41 |
-41 |
-41 |
-41 |
300 KHz |
6.6.3EB.3.5.3 Test requirement (network signalled value "NS_07")
When "NS_07" is indicated in the cell:
– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-7 as appropriate,
and
– the measured average power of spurious emission, derived in step 4, shall not exceed the described value in Table 6.6.3EB.3.5.3-1. These requirements also apply for the frequency ranges that are less than ΔfOOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.
Table 6.6.3EB.3.5.3-1: Additional requirements (network signalled value "NS_07")
|
Frequency band (MHz) |
Channel bandwidth / Spectrum emission limit (dBm) |
Measurement bandwidth |
|
10 MHz |
||
|
769 ≤ f ≤ 775 |
-55.5 |
6.25 kHz |
|
Note: The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB. |
||
6.6.3EB.3.5.4 to 6.6.3EB.3.5.6 reserved
6.6.3EB.3.5.7 Test requirement (network signalled value "NS_12")
When "NS 12" is indicated in the cell:
– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-12 as appropriate,
and
– the power of any UE emission shall not exceed the levels specified in Table 6.6.3EB.3.7-1. This requirement also applies for the frequency ranges that are less than ΔfOOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.
Table 6.6.3EB.3.5.7-1: Additional requirements
|
Frequency band (MHz) |
Channel bandwidth/ Spectrum emission limit (dBm) |
Measurement bandwidth |
|
1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz |
||
|
806 ≤ f ≤ 813.5 |
-42 |
6.25 kHz |
|
NOTE 1: The requirement applies for E-UTRA carriers with lower channel edge at or above 814.2 MHz. NOTE 2: The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB. |
||
6.6.3EB.3.5.8 Test requirement (network signalled value "NS_13")
When "NS 13" is indicated in the cell:
– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-13 as appropriate,
and
– the power of any UE emission shall not exceed the levels specified in Table 6.6.3EB.3.5.8-1. This requirement also applies for the frequency ranges that are less than ΔfOOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.
Table 6.6.3EB.3.5.8-1: Additional requirements
|
Frequency band (MHz) |
Channel bandwidth/ Spectrum emission limit (dBm) |
Measurement bandwidth |
|
1.4, 3, 5 MHz |
||
|
806 ≤ f ≤ 816 |
-42 |
6.25 kHz |
|
NOTE 1: The requirement applies for E-UTRA carriers with lower channel edge at or above 819 MHz. NOTE 2: The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB. |
||
6.6.3EB.3.5.9 Test requirement (network signalled value "NS_14")
When "NS 14" is indicated in the cell:
– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-14 as appropriate,
and
– the power of any UE emission shall not exceed the levels specified in Table 6.6.3EB.3.5.9-1. This requirement also applies for the frequency ranges that are less than ΔfOOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.
Table 6.6.3EB.3.5.9-1: Additional requirements
|
Frequency band (MHz) |
Channel bandwidth/ Spectrum emission limit (dBm) |
Measurement bandwidth |
|
10 MHz, 15 MHz |
||
|
806 ≤ f ≤ 816 |
-42 |
6.25 kHz |
|
NOTE 1: The requirement applies for E-UTRA carriers with lower channel edge at or above 824 MHz. NOTE 2: The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB. |
||
6.6.3EB.3.5.10 Test requirement (network signalled value "NS_15")
When "NS 15" is indicated in the cell:
the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-15 as appropriate,
and
– the power of any UE emission shall not exceed the levels specified in Table 6.6.3EB.3.5.10-1. This requirement also applies for the frequency ranges that are less than ΔfOOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.
Table 6.6.3EB.3.5.10-1: Additional requirements
|
Frequency band (MHz) |
Channel bandwidth / Spectrum emission limit (dBm) |
Measurement bandwidth |
Note |
|
1.4, 3, 5, 10, 15 MHz |
|||
|
851 ≤ f ≤ 859 |
-53 |
6.25 kHz |
6.6.3EB.3.5.11 Test requirement (network signalled value "NS_16")
When "NS 16" is indicated in the cell:
the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-16 as appropriate,
and
– the power of any UE emission shall not exceed the levels specified in Table 6.6.3EB.3.5.11-1. This requirement also applies for the frequency ranges that are less than ΔfOOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.
Table 6.6.3EB.3.5.11-1: Additional requirements
|
Frequency band (MHz) |
Channel bandwidth / Spectrum emission limit (dBm) |
Measurement bandwidth |
Note |
|
1.4, 3, 5, 10 MHz |
|||
|
790 ≤ f ≤ 803 |
-32 |
1 MHz |
6.6.3EB.3.5.12 Test requirement (network signalled value "NS_17")
When "NS 17" is indicated in the cell:
the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-17 as appropriate,
and
– the power of any UE emission shall not exceed the levels specified in Table 6.6.3EB.3.5.12-1. This requirement also applies for the frequency ranges that are less than ΔfOOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.
Table 6.6.3EB.3.5.12-1: Additional requirements
|
Frequency band (MHz) |
Channel bandwidth / Spectrum emission limit (dBm) |
Measurement bandwidth |
Note |
|
5, 10 MHz |
|||
|
470 ≤ f ≤ 710 |
-26.2 |
6 MHz |
1 |
|
Note 1: Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. |
|||
6.6.3EB.3.5.13 Test requirement (network signalled value "NS_18")
When "NS 18" is indicated in the cell:
the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-18 as appropriate,
and
– the power of any UE emission shall not exceed the levels specified in Table 6.6.3EB.3.5.13-1. This requirement also applies for the frequency ranges that are less than ΔfOOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.
Table 6.6.3EB.3.5.13-1: Additional requirements
|
Frequency band (MHz) |
Channel bandwidth / Spectrum emission limit (dBm) |
Measurement bandwidth |
Note |
|
5, 10, 15, 20 MHz |
|||
|
692 ≤ f ≤ 698 |
-26.2 |
6 MHz |