7.5A.3 Adjacent Channel Selectivity (ACS) for CA (inter-band DL CA without UL CA)
36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification
7.5A.3.1 Test purpose
The test purpose is the same as in clause 7.5A.1.1.
7.5A.3.2 Test applicability
This test applies to all types of E-UTRA UE release 10 and forward that support inter-band DL CA.
This test case also applies to all types of E-UTRA UE release 12 and forward that support 2DL CA with FDD-TDD inter-band CA.
This test case also applies to all types of E-UTRA UE release 13 and forward that support DL LAA.
This test case applies only for CA configurations that do not support UL CA.
7.5A.3.3 Minimum conformance requirements
The minimum conformance requirements are defined in clause 7.5A.0.
7.5A.3.4 Test description
7.5A.3.4.1 Initial conditions
Same as in clause 7.5A.1.4.1 with the following exceptions:
– Instead of Table 5.4.2A.1-1🡪 use Table 5.4.2A.1-2.- Instead of Table 7.5A.1.4.1-1🡪 use Table 7.5A.3.4.1-1.
– Instead of clause 7.5A.1.4.3 🡪 use clause 7.5A.3.4.3.
Table 7.5A.3.4.1-1: Test Configuration Table
|
Initial Conditions |
||||||
|
Test Environment as specified in TS 36.508[7] subclause 4.1 |
NC |
|||||
|
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 7.1-2 |
A: Mid range for PCC and SCC |
|||||
|
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE |
Highest NRB_agg for PCC and SCC |
|||||
|
Test Parameters for CA Configurations |
||||||
|
CA Configuration / NRB_agg |
DL Allocation |
UL Allocation |
||||
|
PCC |
SCCs |
CC |
PCC & SCC |
CC |
PCC |
|
|
50 |
50 |
QPSK |
50 |
50 |
QPSK |
50 |
|
50 |
50 |
QPSK |
50 |
50 |
QPSK |
25 |
|
50 |
50 |
QPSK |
50 |
50 |
QPSK |
20 |
|
50 |
50 |
QPSK |
50 |
50 |
QPSK |
16 |
|
50 |
75 |
QPSK |
50 |
75 |
QPSK |
25 |
|
50 |
100 |
QPSK |
50 |
100 |
QPSK |
50 |
|
50 |
100 |
QPSK |
50 |
100 |
QPSK |
25 |
|
50 |
100 |
QPSK |
50 |
100 |
QPSK |
20 |
|
50 |
100 |
QPSK |
50 |
100 |
QPSK |
16 |
|
75 |
25 |
QPSK |
75 |
25 |
QPSK |
75 |
|
75 |
25 |
QPSK |
75 |
25 |
QPSK |
20 |
|
75 |
50 |
QPSK |
75 |
50 |
QPSK |
25 |
|
75 |
75 |
QPSK |
75 |
75 |
QPSK |
25 |
|
75 |
100 |
QPSK |
75 |
100 |
QPSK |
25 |
|
100 |
50 |
QPSK |
100 |
50 |
QPSK |
100 |
|
100 |
50 |
QPSK |
100 |
50 |
QPSK |
75 |
|
100 |
50 |
QPSK |
100 |
50 |
QPSK |
50 |
|
100 |
75 |
QPSK |
100 |
75 |
QPSK |
100 |
|
100 |
75 |
QPSK |
100 |
75 |
QPSK |
50 |
|
100 |
100 |
QPSK |
100 |
100 |
QPSK |
100 |
|
100 |
100 |
QPSK |
100 |
100 |
QPSK |
75 |
|
100 |
100 |
QPSK |
100 |
100 |
QPSK |
50 |
|
100 |
100 |
QPSK |
100 |
100 |
QPSK |
45 |
|
100 |
100 |
QPSK |
100 |
100 |
QPSK |
25 |
|
100 |
100 |
QPSK |
100 |
100 |
QPSK |
20 |
|
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration, which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-2. Note 2: Depending on CA configurations, only the appropriate Uplink RB allocation value according to table 7.3A.3.5-2 for UE supporting one uplink carrier is tested per Test CA configuration. Note 3: The UL resource blocks shall be located as close as possible to the downlink PCC but confined within the transmission bandwidth configuration for the channel bandwidth (Table 5.4.2-1). Note 4: The frequencies of PCC and SCC shall be switched and tested in each configuration, according to the UE declared capability for UL support (within CA operation) in the individual bands. |
||||||
7.5A.3.4.2 Test procedure
1. Configure SCC according to Annex C.0, C.1 and Annex C.3.1 for all downlink physical channels.
2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4.
3. SS activates SCC by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).
4. SS transmits PDSCH via PDCCH DCI format 1A for C_RNTI to transmit the DL RMC according to Tables 7.5A.3.4.1-1 on both PCC and SCC. The SS sends downlink MAC padding bits on the DL RMC.
5. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 7.5A.3.4.1-1 on PCC. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.
6. Set the Downlink signal level for PCC and SCC to the value as defined in Table 7.5A.3.5-2 (Case 1), or 7.5A.3.5-2a for operating band 46. Send Uplink power control commands to the UE (less or equal to 1dB step size should be used), to ensure that the UE output power is within +0, – 3.4 dB of the target level in Table 7.5A.3.5-2 (Case 1) for carrier frequency f ≤ 3.0GHz or within +0, -4.0 dB of the target level for carrier frequency 3.0GHz < f ≤ 4.2GHz, for at least the duration of the Throughput measurement.
7. Set the Interferer signal level to the value as defined in Table 7.5A.3.5-2 (Case 1), or 7.5A.3.5-2a for operating band 46, and frequency below the wanted signal, using a modulated interferer bandwidth as defined in Annex D of the present document.
8. Measure the average throughput of SCC for a duration sufficient to achieve statistical significance according to Annex G.2.
9. Repeat steps from 6 to 8, using an interfering signal above the wanted signal in Case 1 at step 7.
10. Set the Downlink signal level for PCC and SCC to the value as defined in Table 7.5A.3.5-3 (Case 2), or 7.5A.3.5-3a for operating band 46. Send Uplink power control commands to the UE (less or equal to 1dB step size should be used), to ensure that the UE output power is within +0, – 3.4 dB of the target level in Table 7.5A.3.5-3 (Case 2) for carrier frequency f ≤ 3.0GHz or within +0, -4.0 dB of the target level for carrier frequency 3.0GHz < f ≤ 4.2GHz, for at least the duration of the Throughput measurement.
11. Set the Interferer signal level to the value as defined in Table 7.5A.3.5-3 (Case 2), or 7.5A.3.5-3a for operating band 46, and frequency below the wanted signal, using a modulated interferer bandwidth as defined in Annex D of the present document.
12. Measure the average throughput of SCC for a duration sufficient to achieve statistical significance according to Annex G.2.
13. Repeat steps from 10 to 12, using an interfering signal above the wanted signal in Case 2 at step 11.
7.5A.3.4.3 Message contents
The message contents are the same as in clause 7.5.4.3.
7.5A.3.5 Test Requirements
For inter-band carrier aggregation with uplink assigned to one E-UTRA band, the adjacent channel requirements are defined with the uplink active on the band other than the band whose downlink is being tested i.e. the requirements are tested only for the SCell downlink. The UE shall meet the requirement specified in Table 7.5A.3.5-1 (originated from the single carrier Table 7.5.3.5-1), or the requirement specified in Table 7.5A.3.5-1a for operating band 46, with the test parameters specified in Tables 7.5A.3.5-2 and 7.5A.3.5-3 (originated from the single carrier Tables 7.5.5-2 and 7.5.5-3), or with the test parameters specified in Tables 7.5A.3.5-2a and 7.5A.3.5-3a for operating band 46, for each component carrier, when operated as SCell, while both downlink carriers are active.
The test requirements do not apply when the interfering signal overlaps with the channel bandwidth of any downlink CC.
Table 7.5A.3.5-1: Adjacent channel selectivity
|
Channel bandwidth |
|||||||
|
Rx Parameter |
Units |
1.4 MHz |
3 MHz |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
|
ACS |
dB |
33.0 |
33.0 |
33.0 |
33.0 |
30 |
27 |
Table 7.5A.3.5-1a: Adjacent channel selectivity
|
E-UTRA band |
Rx Parameter |
Units |
Channel bandwidth |
|||||
|
1.4 |
3 |
5 |
10 |
15 |
20 |
|||
|
46 |
ACS |
dB |
33 |
27 |
||||
Table 7.5A.3.5-2: Test parameters for Adjacent channel selectivity, Case 1
|
Rx Parameter |
Units |
Channel bandwidth |
|||||
|
1.4 MHz |
3 MHz |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
||
|
Pw in Transmission Bandwidth Configuration, per CC |
dBm |
REFSENS + 14 dB |
|||||
|
PInterferer |
dBm |
REFSENS for SCC +45.5dB |
REFSENS for SCC+45.5dB |
REFSENS +45.5dB |
REFSENS for SCC+45.5dB |
REFSENS for SCC+42.5dB |
REFSENSfor SCC +39.5dB |
|
BWInterferer |
MHz |
1.4 |
3 |
5 |
5 |
5 |
5 |
|
FInterferer (offset from SCC) |
MHz |
1.4+0.0025 / -1.4-0.0025 |
3+0.0075 / -3-0.0075 |
5+0.0025 / -5-0.0025 |
7.5+0.0075 / -7.5-0.0075 |
10+0.0125 / -10-0.0125 |
12.5+0.0025 / -12.5-0.0025 |
|
Note 1: The transmitter shall be set to 4dB below PCMAX_L at the minimum uplink configuration specified in Table 7.3.3-2 with PCMAX_L as defined in clause 6.2.5. Note 2: The interferer consists of the Reference measurement channel specified in Annex A.3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD as described in Annex A.5.1.1/A.5.2.1 and set-up according to Annex C.3.1. |
|||||||
Table 7.5A.3.5-2a: Test parameters for Adjacent channel selectivity, Case 1
|
E-UTRA Band |
Rx Parameter |
Units |
Channel bandwidth |
|||||
|
1.4 MHz |
3 MHz |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
|||
|
46 |
Power in Transmission Bandwidth Configuration |
dBm |
REFSENS + 14 dB |
|||||
|
PInterferer |
dBm |
REFSENS+45.5dB |
REFSENS +39.5dB |
|||||
|
BWInterferer |
MHz |
20 |
20 |
|||||
|
FInterferer (offset) |
MHz |
15+0.0075/-15-0.0075 |
20+0.0025 / -20-0.0025 |
|||||
|
NOTE 1: In a band capable of uplink operation, the transmitter shall be set to 4dB below PCMAX_L at the minimum uplink configuration specified in Table 7.3.3-2 with PCMAX_L as defined in subclause 6.2.5. NOTE 2: The interferer consists of the Reference measurement channel specified in Annex A.3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD/FS3 as described in Annex A.5.1.1/A.5.2.1/A.5.4.1 and set-up according to Annex C.3.1. |
||||||||
Table 7.5A.3.5-3: Test parameters for Adjacent channel selectivity, Case 2
|
Rx Parameter |
Units |
Channel bandwidth |
|||||
|
1.4 MHz |
3 MHz |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
||
|
Pw in Transmission Bandwidth Configuration, per CC |
dBm |
-56.5 |
-56.5 |
-56.5 |
-56.5 |
-53.5 |
-50.5 |
|
PInterferer |
dBm |
-25 |
|||||
|
BWInterferer |
MHz |
1.4 |
3 |
5 |
5 |
5 |
5 |
|
FInterferer (offset from SCC) |
MHz |
1.4+0.0025 / -1.4-0.0025 |
3+0.0075 / -3-0.0075 |
5+0.0025 / -5-0.0025 |
7.5+0.0075 / -7.5-0.0075 |
10+0.0125 / -10-0.0125 |
12.5+0.0025 / -12.5-0.0025 |
|
Note 1: The transmitter shall be set to 24dB below PCMAX_L at the minimum uplink configuration specified in Table 7.3.3-2 with PCMAX_L as defined in clause 6.2.5. Note 2: The interferer consists of the Reference measurement channel specified in Annex A.3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD/FS3 as described in Annex A.5.1.1/A.5.2.1/A.5.4.1 and set-up according to Annex C.3.1. |
|||||||
Table 7.5A.3.5-3a: Test parameters for Adjacent channel selectivity, Case 2
|
E-UTRA band |
Rx Parameter |
Units |
Channel bandwidth |
|||||
|
1.4 MHz |
3 MHz |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
|||
|
46 |
Power in Transmission Bandwidth Configuration |
dBm |
-56.5 |
-50.5 |
||||
|
PInterferer |
dBm |
-25 |
||||||
|
BWInterferer |
MHz |
20 |
20 |
|||||
|
FInterferer (offset) |
MHz |
15+0.0075/-15-0.0075 |
20+0.0025 / -20-0.0025 |
|||||
|
NOTE 1: In a band capable of uplink operation, the transmitter shall be set to 24dB below PCMAX_L at the minimum uplink configuration specified in Table 7.3.3-2 with PCMAX_L as defined in subclause 6.2.5. NOTE 2: The interferer consists of the Reference measurement channel specified in Annex A.3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD/FS3 as described in Annex A.5.1.1/A.5.2.1/A.5.4.1 and set-up according to Annex C.3.1. |
||||||||