6.2.4_2 Additional Maximum Power Reduction (A-MPR) for UL 64QAM

36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification

Tools: ARFCN - Frequency Conversion for 5G NR/LTE/UMTS/GSM

Editor’s note:

Test requirements values in this section need to be reviewed in order to take into account notes in Table 6.2.5.3-2: ΔT_IB,cregarding ΔT_IB,c and asymmetric lower tolerances in table 6.2.2.3-1.

6.2.4_2.1 Test purpose

Same test purpose as in clause 6.2.4.1

6.2.4_2.2 Test applicability

The requirements of this test apply in test case 6.6.2.2_1 Additional Spectrum Emission Mask for network signalled values NS_03, NS_04, NS_06, NS_07, NS_11, NS_20, NS_21, NS_27 and NS_35 to all types of E-UTRA UE from release 13 and forward that support UL 64QAM.

The requirements of this test apply in test case 6.6.3.3_1 Additional Spurious Emissions for network signalled values NS_04, NS_05, NS_07, NS_08, NS_09, NS_11, NS_12, NS_13, NS_14, NS_15, NS_16, NS_17, NS_18, NS_19, NS_20, NS_21, NS_22, NS_23, NS_24, NS_25, NS_27, NS_36, NS_38, NS_39, NS_56 to all types of E-UTRA UE from release 13 and forward that support UL 64QAM.

NOTE: As a result TC 6.2.4_2 has not been included in the test case applicability table 4.1-1, TS 36.521-2. This does not preclude the test from being used for R&D or other purposes if deemed useful.

6.2.4_2.3 Minimum conformance requirements

Same minimum conformance requirements as in clause 6.2.4.3

6.2.4_2.4 Test description

6.2.4_2.4.1 Initial condition

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and channel bandwidths based on E-UTRA operating bands specified in table 5.4.2.1-1. All of these configurations shall be tested with applicable test parameters for each channel bandwidth, and are shown in table 6.2.4_2.4.1-1 through table 6.2.4_2.4.1-27. The details of the uplink reference measurement channels (RMCs) are specified in Annex A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.2.4_2.4.1-1: Test Configuration Table (network signalled value "NS_03")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					NC
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Low range, Mid range, High range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					Lowest, 5MHz, 10MHz, Highest
Test Parameters for NS_03 A-MPR
		Downlink Configuration			Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation		Mod’n	RB allocation
			FDD	TDD		FDD	TDD
1	1.4MHz	N/A for A-MPR testing			64QAM	5	5
2	3MHz				64QAM (Note 5)	15	15
3	3MHz				64QAM	4	4
4	5MHz				64QAM (Note 5)	25	25
5	5MHz				64QAM	8	8
6	10MHz				64QAM (Note 5)	50	50
7	10MHz				64QAM	12	12
8	15MHz				64QAM (Note 5)	75	75
9	15MHz				64QAM	16	16
10	20MHz				64QAM (Note 5)	100	100
11	20MHz				64QAM	18	18
Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4_2.5 as not all combinations are necessarily required based on the applicability of the UE. Note 3: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 4: For band 23, above table only applies to mid and high range test frequencies. Low range test frequencies will be covered by NS_11 test configuration table. Note 5: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_03.

Table 6.2.4_2.4.1-2: Test Configuration Table (network signalled value "NS_04")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range, Mid Range, High Range Additional test frequencies for Rel-12 to Rel-13 and bit 2 of modifiedMPRbehavior = 0: For 5 MHz bandwidth: 2499.6 MHz, N_UL= 39696 For 10 MHz bandwidth: 2504.1 MHz, N_UL= 39731 For 15 MHz bandwidth: 2510.9 MHz, N_UL= 39799 For 20 MHz bandwidth: 2517.6 MHz, N_UL= 39866 Additional test frequencies for Rel-12 and later and bit 2 of modifiedMPRbehavior = 1: For 5 MHz bandwidth: 2500.6 MHz, N_UL= 39686 For 10 MHz bandwidth: 2504.1 MHz, N_UL= 39731 For 15 MHz bandwidth: 2510.9 MHz, N_UL= 39799 For 20 MHz bandwidth: 2517.6 MHz, N_UL= 39866
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_04 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1 (Note 1)	5MHz	N/A for A-MPR testing		64QAM	16	9
2 (Note 2)	5MHz			64QAM	25	0
3	10MHz			64QAM	50	0
4	15MHz			64QAM	75	0
5	20MHz			64QAM	100	0
Note 1: Only applicable for Low Range. Note 2: Only applicable for Mid, High Range and additional test frequencies. Note 3: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_04.

Table 6.2.4_2.4.1-3: Test Configuration Table (network signalled value "NS_05")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low range, Mid range In case of Low range: – For 5 MHz Channel Bandwidth: 1927.2 MHz (NUL = 18072) – For 10 MHz Channel Bandwidth: 1934.7 MHz (NUL = 18147) – For 15 MHz Channel Bandwidth: 1932.5 MHz (NUL = 18125) – For 20 MHz Channel Bandwidth: 1930 MHz (NUL = 18100)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_05 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for A-MPR testing		64QAM	25
2	10MHz			64QAM	50 (Note 2)
3	15MHz			64QAM	75 (Note 2)
4	20MHz			64QAM	100 (Note 2)
5	10MHz			64QAM	50 (Note 3)
6	15MHz			64QAM	75 (Note 3)
7	20MHz			64QAM	100 (Note 3)
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4_2.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for Low Range. Note 3: Applies only for Mid Range. Note 4: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_05.

Table 6.2.4_2.4.1-4: Test Configuration Table (network signalled value "NS_06")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low range, Mid range, High range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				Lowest, 5MHz, 10MHz, Highest
Test Parameters for NS_06 A-MPR
		Downlink Configuration		Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	1.4MHz	N/A for A-MPR testing		64QAM	5
2	5MHz			64QAM	8
3	10MHz			64QAM	12
Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4_2.5 as not all combinations are necessarily required based on the applicability of the UE. Note 3: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 4: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_06.

Table 6.2.4_2.4.1-5: Test Configuration Table (network signalled value "NS_07")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Mid range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				10MHz
Test Parameters for NS_07 A-MPR
		Downlink Configuration		Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	10MHz	N/A for A-MPR testing		64QAM	36	13
2	10MHz			64QAM	16	19
3	10MHz			64QAM	30	19
4	10MHz			64QAM	50	0
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4_2.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_07.

Table 6.2.4_2.4.1-6: Test Configuration Table (network signalled value "NS_08")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				High range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz
Test Parameters for NS_08 A-MPR
		Downlink Configuration		Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for A-MPR testing		64QAM	25
2	10MHz			64QAM	50
3	15MHz			64QAM	75
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4_2.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_08.

Table 6.2.4_2.4.1-7: Test Configuration Table (network signalled value "NS_09")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				High range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for A-MPR testing		64QAM	25
2	10MHz			64QAM	50
3	15MHz			64QAM	75
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4_2.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_09.

Table 6.2.4_2.4.1-8: Test Configuration Table (network signalled value "NS_10")

Void, not tested

Table 6.2.4_2.4.1-9: Test Configuration Table (network signalled value "NS_11")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				For 3 MHz Channel Bandwidth: a. 2001.5 MHz (N_UL= 25515) b. 2004.5 MHz (N_UL = 25545) For 5 MHz Channel Bandwidth a. 2002.5 MHz (N_UL = 25525) b. 2004.5 MHz (N_UL = 25545) c. 2007.5 MHz (N_UL = 25575) For 10 MHz Channel Bandwidth a. 2005 MHz (N_UL = 25550) b. 2005.5 MHz (N_UL = 25555) c. 2015 MHz (N_UL = 25650) For 15 MHz Channel Bandwidth a. 2007.5 MHz (N_UL = 25575) b. 2012.5 MHz (N_UL = 25625) For 20 MHz Channel Bandwidth a. 2010 MHz (N_UL = 25600)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				3MHz, 5MHz, 10MHz, 15MHz, 20MHz
				3MHz, 5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_11 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	3MHz	N/A for A-MPR testing		64QAM	6
2	3MHz			64QAM (Note 3)	15
3	5MHz			64QAM	8
4	5MHz			64QAM (Note 3)	25
5	10MHz			64QAM	12
6	10MHz			64QAM (Note 3)	50
7	15MHz			64QAM (Note 3)	8
8	15MHz			64QAM (Note 3)	25
9	15MHz			64QAM (Note 3)	30
10	15MHz			64QAM (Note 3)	75
11	20MHz			64QAM (Note 3)	10
12	20MHz			64QAM (Note 3)	25
13	20MHz			64QAM (Note 3)	100
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4_2.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 3: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_11.

Table 6.2.4_2.4.1-10: Test Configuration Table (network signalled value "NS_12")

Initial Conditions
Test Environment				NC
(as specified in TS 36.508 [7] subclause 4.1)
Test Frequencies				For 1.4 MHz Channel Bandwidth: UL 814.9 MHz (N_UL = 26699) For 5 MHz Channel Bandwidth: UL 816.7 MHz (N_UL = 26717) For 10 MHz Channel Bandwidth: UL 819.2 MHz (N_UL = 26742) For 15 MHz Channel Bandwidth: UL 821.7 MHz (N_UL = 26767)
(as specified in TS 36.508 [7] subclause 4.3.1)
Test Channel Bandwidths				1.4 MHz, 5 MHz, 10 MHz and 15 MHz
(as specified in TS 36.508 [7] subclause 4.3.1)
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	1.4 MHz	N/A for A-MPR testing		64QAM	6	0
2	5 MHz			64QAM	25	0
3	10 MHz			64QAM	50	0
4	15 MHz			64QAM	75	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_12.

Table 6.2.4_2.4.1-11: Test Configuration Table (network signalled value "NS_13")

Initial Conditions
Test Environment				NC
(as specified in TS 36.508 [7] subclause 4.1)
Test Frequencies				For 5 MHz Channel Bandwidth: UL 821.5 MHz (N_UL = 26765)
(as specified in TS 36.508 [7] subclause 4.3.1)
Test Channel Bandwidths				5 MHz
(as specified in TS 36.508 [7] subclause 4.3.1)
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	5 MHz	N/A for A-MPR testing		64QAM	25	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_13.

Table 6.2.4_2.4.1-12: Test Configuration Table (network signalled value "NS_14")

Initial Conditions
Test Environment				NC
(as specified in TS 36.508 [7] subclause 4.1)
Test Frequencies				For 10 MHz Channel Bandwidth: UL 829 MHz (N_UL = 26840) For 15 MHz Channel Bandwidth: Mid range
(as specified in TS 36.508 [7] subclause 4.3.1)
Test Channel Bandwidths				10 MHz, 15 MHz
(as specified in TS 36.508 [7] subclause 4.3.1)
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	10 MHz	N/A for A-MPR testing		64QAM	50	0
2	15 MHz			64QAM	75	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_14.

Table 6.2.4_2.4.1-13: Test Configuration Table (network signalled value "NS_15")

Initial Conditions

Test Environment

(as specified in TS 36.508 [7] subclause 4.1)

Test Frequencies

(as specified in TS 36.508 [7] subclause 4.3.1)

For 1.4 MHz Channel Bandwidth: High range

For 3 MHz Channel Bandwidth: UL 843.5 MHz (N_UL = 26985) or High range

For 5 MHz Channel Bandwidth: UL 842.5 MHz (N_UL = 26975) or High range

For 10 MHz Channel Bandwidth: UL 840 MHz (N_UL = 26950) or High range

For 15 MHz Channel Bandwidth: UL 837.5 MHz (N_UL = 26925) or High range

Test Channel Bandwidths

(as specified in TS 36.508 [7] subclause 4.3.1)

1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz

Test Parameters for Channel Bandwidths

Downlink Configuration

Uplink Configuration

Configuration ID

Ch BW

Mod’n

RB allocation

Mod’n

RB allocation FDD

RBstart FDD

1 (note 1)

1.4 MHz

N/A for A-MPR testing

64QAM

2 (note 1)

3 MHz

64QAM

3 (note 1)

5 MHz

64QAM

4 (note 1)

10 MHz

64QAM

5 (note 1)

15 MHz

64QAM

Note 1: Applicable only to high range frequency testing.

Note 2: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_15.

Table 6.2.4_2.4.1-14: Test Configuration Table (network signalled value "NS_16")

Initial Conditions

Test Environment

(as specified in TS 36.508 [7] subclause 4.1)

Test Frequencies

(as specified in TS 36.508 [7] subclause 4.3.1)

For 1.4 MHz Channel Bandwidth: Low range

For 3 MHz Channel Bandwidth: Low range, 810 MHz (N_UL= 27070)

For 5 MHz Channel Bandwidth: Low range, 811 MHz (N_UL= 27080), 814.5 MHz (N_UL= 27115)

For 10 MHz Channel Bandwidth: Low range, 813.5 MHz (N_UL= 27105), 817 MHz (N_UL= 27140)

Test Channel Bandwidths

(as specified in TS 36.508 [7] subclause 4.3.1)

1.4 MHz, 3 MHz, 5 MHz, 10 MHz

Test Parameters for Channel Bandwidths

Downlink Configuration

Uplink Configuration

Configuration ID

Ch BW

Mod’n

RB allocation

Mod’n

RB allocation FDD

RBstart FDD

1.4 MHz

N/A for A-MPR testing

64QAM

3 MHz

64QAM

5 MHz

64QAM

10 MHz

64QAM

Note 1: Applies only for 10 MHz channel for Low Range, and 813.5 MHz

Note 2: Applies only for 10 MHz channel for 817 MHz range

Note 3: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_16.

Table 6.2.4_2.4.1-15: Test Configuration Table (network signalled value "NS_17")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Mid range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for A-MPR testing		64QAM	25
2	10MHz			64QAM	50
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_17.

Table 6.2.4_2.4.1-16: Test Configuration Table (network signalled value "NS_18")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for A-MPR testing		64QAM	25
2	10MHz			64QAM	50
3	15MHz			64QAM	75
4	20MHz			64QAM	100
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_18.

Table 6.2.4_2.4.1-17: Test Configuration Table (network signalled value "NS_19")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				3MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	3MHz	N/A for A-MPR testing		64QAM	15
2	10MHz			64QAM	40
3	15MHz			64QAM	45
4	20MHz			64QAM	50
Note 1: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 2: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_19.

Table 6.2.4_2.4.1-18: Test Configuration Table (network signalled value "NS_20")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal

Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				For 5 MHz Channel Bandwidth a. 2002.5 MHz (N_UL = 25525) b. 2007.5 MHz (N_UL = 25575) c. 2012.5 MHz (N_UL = 25625) d. 2017.5 MHz (N_UL = 25675) For 10 MHz Channel Bandwidth a. 2005 MHz (N_UL = 25550) b. 2015 MHz (N_UL = 25650) For 15 MHz Channel Bandwidth a. 2012.5 MHz (N_UL = 25625) For 20 MHz Channel Bandwidth a. 2010 MHz (N_UL = 25600)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz

Test Parameters for NS_20 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD

1	5MHz	N/A for A-MPR testing		64QAM (Note 3)	15
2	5MHz			64QAM (Note 3)	25
3	10MHz			64QAM	12
4	10MHz			64QAM (Note 3)	50

5	15MHz			64QAM (Note 3)	25
6	15MHz			64QAM (Note 3)	36
7	15MHz			64QAM (Note 3)	75
8	20MHz			64QAM	18
9	20MHz			64QAM (Note 3)	25
10	20MHz			64QAM (Note 3)	75
11	20MHz			64QAM (Note 3)	100
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4_2.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 3: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_20.

Table 6.2.4_2.4.1-19: Test Configuration Table (network signalled value "NS_21")

Initial Conditions

Test Environment

(as specified in TS 36.508 [7] subclause 4.1)

Test Frequencies

(as specified in TS 36.508 [7] subclause 4.3.1)

Low range or High range

Test Channel Bandwidths

(as specified in TS 36.508 [7] subclause 4.3.1)

10 MHz

Test Parameters for Channel Bandwidths

Downlink Configuration

Uplink Configuration

Configuration ID

Ch BW

Mod’n

RB allocation

Mod’n

RB allocation FDD

RBstart FDD

1 (note 1)

10 MHz

N/A for A-MPR testing

64QAM

Note 1: Applicable only to high range frequency testing.

Note 2: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_21.

Table 6.2.4_2.4.1-20: Test Configuration Table (network signalled value "NS_22")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range, Mid Range, High Range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_22 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation TDD	RB_start TDD
1	5MHz	N/A for A-MPR testing		64QAM	1	0
2	5MHz			64QAM	1	24
3	10MHz			64QAM	1	0
4	10MHz			64QAM	1	49
5	15MHz			64QAM	1	0
6	15MHz			64QAM	1	74
7	20MHz			64QAM	1	0
8	20MHz			64QAM	1	99
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_22.

Table 6.2.4_2.4.1-21: Test Configuration Table (network signalled value "NS_23")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range, Mid Range, High Range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz
Test Parameters for NS_23 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation TDD	RB_start TDD
1	5MHz	N/A for A-MPR testing		64QAM	1	0
2	5MHz			64QAM	1	24
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_23.

Table 6.2.4_2.4.1-22: Test Configuration Table (network signalled value "NS_24")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 10 and 15 MHz CH BW: 1980 MHz (N_UL = 131672) 1990 MHz (N_UL = 131772)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_24 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	High	5MHz	N/A for A-MPR testing		64QAM	25	0
2	1980	10MHz			64QAM	50	0
3	1990	10MHz			64QAM	50	0
4	1980	15MHz			64QAM	75	0
5	High	20MHz			64QAM	100	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_24.

Table 6.2.4_2.4.1-23: Test Configuration Table (network signalled value "NS_25")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 10 and 15 MHz CH BW: 1980 MHz (N_UL = 132672) 1990 MHz (N_UL = 132772)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_25 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	High	5MHz	N/A for A-MPR testing		64QAM	25	0
2	1980	10MHz			64QAM	50	0
3	1990	10MHz			64QAM	50	0
4	1980	15MHz			64QAM	75	0
5	1980	20MHz			64QAM	100	0
6	High	20MHz			64QAM	100	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_25.

Table 6.2.4_2.4.1-24: Reserved

Table 6.2.4_2.4.1-25: Test Configuration Table (network signalled value "NS_27")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to Frequency columnin test parameters
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_27 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	Frequency	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	Low/Mid/High	5MHz			64QAM	25	0
2	Low/Mid/High	10MHz			64QAM	50	0
3	Low/Mid/High	15MHz			64QAM	75	0
4	Low/Mid/High	20MHz			64QAM	100	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_27.

Table 6.2.4_2.4.1-26: Test Configuration Table (network signalled value "NS_35")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low range, Mid range, High range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_35 A-MPR
		Downlink Configuration		Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for A-MPR testing		64QAM	8
2	10MHz			64QAM	12
3	15MHz			64QAM	16
4	20MHz			64QAM	18
Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4_2.5 as not all combinations are necessarily required based on the applicability of the UE. Note 3: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 4: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_35.

Table 6.2.4_2.4.1-27: Test Configuration Table (network signalled value "NS_36")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 700.5 MHz (N_UL = low range) 705.5 MHz (N_UL=132747) 10 MHz CH BW: 703 MHz (N_UL = low range) 708 MHz (N_UL = 132772) 15 MHz CH BW: 705.5 MHz (N_UL = low range) 710.5 MHz (N_UL =132797 )
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz
Test Parameters for NS_36 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	700.5	5MHz	N/A for A-MPR testing		64QAM	25	0
2	705.5	5MHz			64QAM	25	0
3	703	10MHz			64QAM	50	0
4	708	10MHz			64QAM	50	0
5	705.5	15MHz			64QAM	75	0
6	710.5	15MHz			64QAM	75	0
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Void Note 3: Void Note 4: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_36.

Table 6.2.4_2.4.1-28: Test Configuration Table (network signalled value "NS_56")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 1630 MHz (low range) 10 MHz CH BW: 1632.5 MHz (low range)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz
Test Parameters for NS_56 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	1630	5MHz	N/A for A-MPR testing		64QAM	1	0
2	1630	5MHz			64QAM	25	0
3	1632.5	10MHz			64QAM	1	0
4	1632.5	10MHz			64QAM	50	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.2.4_4 is executed with network signalled value NS_56.

Editor’s note: The following lines belong at the end of section 6.2.4_2.4.1. As new tables are added to this section, these lines should always follow the tables.

1. Connect the SS to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure A.3.

2. The parameter settings for the cell are set up according to TS 36.508 [7] clause 4.4.3.

3. Downlink signals are initially set up according to Annex C.0, C.1, and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to the applicable table from Table 6.2.4_2.4.1-1 to Table 6.2.4_2.4.1-27.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.2.4_2.4.3.

6.2.4_2.4.2 Test procedure

Same test procedure as in clause 6.2.4.4.2 with the following exceptions:

– Instead of Table 6.2.4.4.1-1 to 6.2.4.4.1-27 🡪 use Table 6.2.4_2.4.1-1 to 6.2.4_2.4.1-27

6.2.4_2.4.3 Message contents

Same message contents as in clause 6.2.4.4.3 except table numbers.

6.2.4_2.5 Test requirements

The maximum output power, derived in step 3 shall be within the range prescribed by the nominal maximum output power and tolerance in the applicable table from Table 6.2.4_2.5-1 to Table 6.2.4_2.5-29. The allowed A-MPR values specified in Table 6.2.4_2.3-1 are in addition to the allowed MPR requirements specified in clause 6.2.3. For the UE maximum output power modified by MPR and/or A-MPR, the power limits specified in Table 6.2.5.3-1 apply.

Table 6.2.4_2.5-1: UE Power Class test requirements (network signalled value "NS_03")
(for Bands 4, 10, 23, 35, 36, 66, and 70)

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	2	0	0	21	2	25.7	18.3
2	3	1	0	19	3.5	25.7	14.8
3	2	0	0	21	2	25.7	18.3
4	3	1	0	19	3.5	25.7	14.8
5	2	1	0	20	2.5	25.7	16.8
6	3	1	0	19	3.5	25.7	14.8
7	2	1	0	20	2.5	25.7	16.8
8	3	1	0	19	3.5	25.7	14.8
9	2	1	0	20	2.5	25.7	16.8
10	3	1	0	19	3.5	25.7	14.8
11	2	1	0	20	2.5	25.7	16.8
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-2: UE Power Class test requirements (network signalled value "NS_03")
(for Bands 2 and 25)

Configuration ID	EUTRA band	Test Freq.	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	2, 25	Mid					23	+2.7 / -4.7
1	2, 25	Low, High					23	+2.7 / -7.7
2	2, 25	Mid					23	+2.7 / -8.2
2	2, 25	Low, High					23	+2.7 / -11.2
3	2, 25	Mid					23	+2.7 / -4.7
3	2, 25	Low, High					23	+2.7 / -7.7
4	2, 25	All					23	+2.7 / -8.2
5	2, 25	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -6.2
5	2, 25	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -9.2
6	2, 25	All					23	+2.7 / -8.2
7	2, 25	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -6.2
7	2, 25	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -9.2
8	2, 25	All					23	+2.7 / -8.2
9	2, 25	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -6.2
9	2, 25	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -9.2
10	2, 25	All					23	+2.7 / -8.2
11	2, 25	All					23	+2.7 / -6.2

Table 6.2.4_2.5-3: UE Power Class test requirements (network signalled value "NS_04")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	3	0	0	20	2.5	25.7	16.8
2	3	0	0	20	2.5	25.7	16.8
3 (Low Range)	3	2	0	18	4.0	25.7	13.3
3 (Mid, High Range, 2504.1 MHz)	3	0	0	20	2.5	25.7	16.8
4 (Low Range)	3	3	0	17	5.0	25.7	11.3
4 (Mid, High Range, 2510.9 MHz)	3	0	0	20	2.5	25.7	16.8
5 (Low Range)	3	3	0	17	5.0	25.7	11.3
5 (Mid, High Range, 2517.6 MHz)	3	0	0	20	2.5	25.7	16.8
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-4: UE Power Class test requirements (network signalled value "NS_05")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	3	0	0	20	2.5	25.7	16.8
2	3	1	0	19	3.5	25.7	14.8
3	3	11	0	9	6.0	25.7	2.3
4	3	11	0	9	6.0	25.7	2.3
5	3	0	0	20	2.5	25.7	16.8
6	3	0	0	20	2.5	25.7	16.8
7	3	1	0	19	3.5	25.7	14.8
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-5: UE Power Class test requirements (network signalled value "NS_06")
(for Bands 13, 14, and 17)

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	13,14,17					23	+2.7 / -4.7
2	13,14,17					23	+2.7 / -4.7
3	13,14,17					23	+2.7 / -4.7

Table 6.2.4_2.5-6: UE Power Class test requirements (network signalled value "NS_06")
(for Band 12)

Configuration ID	EUTRA band	Test Freq.	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	12	Mid					23	+2.7 / -4.7
1	12	Low, High					23	+2.7 / -5.2
2	12	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -4.7
2	12	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -7.7
3	12	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -4.7
3	12	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -7.7

Table 6.2.4_2.5-7: UE Power Class test requirements (network signalled value "NS_07")

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	13					23	+2.7 / -21.7
2	13					23	+2.7 / -6.2
3	13					23	+2.7 / -14.7
4	13					23	+2.7 / -21.7

Table 6.2.4_2.5-8: UE Power Class test requirements (network signalled value "NS_08")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	3	0	0	20	2.5	25.7	16.8
2	3	3	0	17	5.0	25.7	11.3
3	3	3	0	17	5.0	25.7	11.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-9: UE Power Class test requirements (network signalled value "NS_09")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	3	0	0	20	2.5	25.7	16.8
2	3	1	0	19	3.5	25.7	14.8
3	3	2	0	18	4.0	25.7	13.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-10: UE Power Class test requirements (network signalled value "NS_10")

Void, not tested

Table 6.2.4_2.5-11: UE Power Class test requirements (network signalled value "NS_11 for Band 23")

Configuration ID	EUTRA Band	Centre Frequency	Class 3 (dBm)	Tol. (dB)
1a	23	2001.5 MHz	23	+ 2.7 / -13.7
1a	23	2001.5 MHz	23	+ 2.7 / -13.7
1b	23	2004.5 MHz	23	+ 2.7 / -8.2
1b	23	2004.5 MHz	23	+ 2.7 / -8.2
2a	23	2001.5 MHz	23	+ 2.7 / -13.7
2a	23	2001.5 MHz	23	+ 2.7 / -13.7
2b	23	2004.5 MHz	23	+ 2.7 / -8.2
2b	23	2004.5 MHz	23	+ 2.7 / -8.2
3a	23	2002.5 MHz	23	+ 2.7 / -14.7
3a	23	2002.5 MHz	23	+ 2.7 / -14.7
3b	23	2004.5 MHz	23	+ 2.7 / -4.7
3b	23	2004.5 MHz	23	+ 2.7 / -4.7
3c	23	2007.5 MHz	23	+ 2.7 / -6.2
3c	23	2007.5 MHz	23	+ 2.7 / -6.2
4a	23	2002.5 MHz	23	+ 2.7 / -15.7
4a	23	2002.5 MHz	23	+ 2.7 / -15.7
4b	23	2004.5 MHz	23	+ 2.7 / -12.7
4b	23	2004.5 MHz	23	+ 2.7 / -12.7
4c	23	2007.5 MHz	23	+ 2.7 / -8.2
4c	23	2007.5 MHz	23	+ 2.7 / -8.2
5a	23	2005 MHz	23	+ 2.7 / -20.7
5a	23	2005 MHz	23	+ 2.7 / -20.7
5b	23	2005.5 MHz	23	+ 2.7 / -20.7
5c	23	2015 MHz	23	+ 2.7 / -4.7
6a	23	2005 MHz	23	+ 2.7 / -21.7
6b	23	2005.5 MHz	23	+ 2.7 / -21.7
6c	23	2015 MHz	23	+ 2.7 / -6.2
7a	23	2007.5 MHz	23	+ 2.7 / -24.7
7b (Note 1)	23	2012.5 MHz	23	+ 2.7 / -18.7
7b (Note 2)	23	2012.5 MHz	23	+ 2.7 / -14.2
8a (Note 1)	23	2007.5 MHz	23	+ 2.7 / -25.7
8a (Note 2)	23	2007.5 MHz	23	+ 2.7 / -6.2
8b (Note 1)	23	2012.5 MHz	23	+ 2.7 / -19.7
8b (Note 2)	23	2012.5 MHz	23	+ 2.7 / -9.7
9a (Note 1)	23	2007.5 MHz	23	+ 2.7 / -25.7
9a (Note 2)	23	2007.5 MHz	23	+ 2.7 / -14.7
9b (Note 1)	23	2012.5 MHz	23	+ 2.7 / -19.7
9b (Note 2)	23	2012.5 MHz	23	+ 2.7 / -9.7
10a	23	2007.5 MHz	23	+ 2.7 / -25.7
10b	23	2012.5 MHz	23	+ 2.7 / -19.7
11	23	2010 MHz	23	+ 2.7 / -24.7
12	23	2010 MHz	23	+ 2.7 / -4.7
13	23	2010 MHz	23	+ 2.7 / -25.7
Note 1: RB_start = RB# 0 Note 2: RB_start = RB# (max +1 – RB allocation)

Table 6.2.4_2.5-12: UE Power Class 3 test requirements (network signalled value "NS_12")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	3	6	1.5	12.5	6	25.7	5.8
2	3	3	0	17	5	25.7	11.3
3	3	2	0	18	4	25.7	13.3
4	3	3	0	17	5	25.7	11.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-13: UE Power Class 3 test requirements (network signalled value "NS_13")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	3	2	0	18	4.0	25.7	13.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-14: UE Power Class 3 test requirements (network signalled value "NS_14")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	3	1	0	19	3	25.7	14.8
2	3	1	0	19	3	25.7	14.8
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-15: UE Power Class test requirements (network signalled value "NS_15")

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	26					23	+2.7 / -13.2
2	26					23	+2.7 / -20.2
3	26					23	+2.7 / -18.7
4	26					23	+2.7 / -18.7
5	26					23	+2.7 / -18.7

Table 6.2.4_2.5-16A: UE Power Class test requirements (network signalled value "NS_16") when lower channel edge is at 807 MHz

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	27					23	+2.7/-6.2
2	27					23	+2.7 / -9.7
3	27					23	+2.7 / -13.7
4	27					23	+2.7 / -15.7

Table 6.2.4_2.5-16B: UE Power Class test requirements (network signalled value "NS_16") when lower channel edge is at 808.5 MHz

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	27	Not tested
2	27					23	+2.7 / -6.2
3	27					23	+2.7 / -11.7
4	27					23	+2.7 / -13.7

Table 6.2.4_2.5-16C: UE Power Class test requirements (network signalled value "NS_16") when lower channel edge is at 812 MHz

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	27	Not tested
2	27	Not tested
3	27					23	+2.7 / -6.2
4	27					23	+2.7 / -11.7

Table 6.2.4_2.5-17: UE Power Class test requirements (network signalled value "NS_17")

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	28					23	+2.7 / -6.2
2	28					23	+2.7 / -6.2

Table 6.2.4_2.5-18: UE Power Class test requirements (network signalled value "NS_18")

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	28					23	+2.7 / -11.7
2	28					23	+2.7 / -14.7
3	28					23	+2.7 / -14.7
4	28					23	+2.7 / -14.7

Table 6.2.4_2.5-19: UE Power Class test requirements (network signalled value "NS_19")

Configuration ID	Test Freq	RB location	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	Low	Full RB	3	0	0	20	2.5	25.7	16.8
2	Low	Low	3	1	0	19	3.5	25.7	14.8
2	Low	High	3	0	0	20	2.5	25.7	16.8
3	Low	Low	3	3	0	17	5	25.7	11.3
3	Low	High	3	0	0	20	2.5	25.7	16.8
4	Low	Low	3	3	0	17	5	25.7	11.3
4	Low	High	3	0	0	20	2.5	25.7	16.8
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-20: UE Power Class test requirements (network signalled value "NS_20 for Band 23")

Configuration ID	EUTRA Band	Centre Frequency	Class 3 (dBm)	Tol. (dB)
1a	23	2002.5 MHz	23	+ 2.7 / -24.7 (Note 1)
1a	23	2002.5 MHz	23	+ 2.7 / -24.7 (Note 1)
1b (Note 2)	23	2007.5 MHz	23	+ 2.7 / -8.2
1b (Note 2)	23	2007.5 MHz	23	+ 2.7 / -8.2
1b (Note 3)	23	2007.5 MHz	23	+ 2.7 / -6.2
1b (Note 3)	23	2007.5 MHz	23	+ 2.7 / -6.2
1c	23	2012.5 MHz	23	+ 2.7 / -6.2
1c	23	2012.5 MHz	23	+ 2.7 / -6.2
1d	23	2017.5 MHz	23	+ 2.7 / -6.2
1d	23	2017.5 MHz	23	+ 2.7 / -6.2
2a	23	2002.5 MHz	23	+ 2.7 / -27.1 (Note 1)
2a	23	2002.5 MHz	23	+ 2.7 / -27.1 (Note 1)
2b	23	2007.5 MHz	23	+ 2.7 / -12.7
2b	23	2007.5 MHz	23	+ 2.7 / -12.7
2c	23	2012.5 MHz	23	+ 2.7 / -6.2
2c	23	2012.5 MHz	23	+ 2.7 / -6.2
2d	23	2017.5 MHz	23	+ 2.7 / -6.2
2d	23	2017.5 MHz	23	+ 2.7 / -6.2
3a (Note 2)	23	2005 MHz	23	+ 2.7 / -25.7 (Note 1)
3a (Note 2)	23	2005 MHz	23	+ 2.7 / -25.7 (Note 1)
3a (Note 3)	23	2005 MHz	23	+ 2.7 / -4.7
3a (Note 3)	23	2005 MHz	23	+ 2.7 / -4.7
3b	23	2015 MHz	23	+ 2.7 / -4.7
4a	23	2005 MHz	23	+ 2.7 / -26.7 (Note 1)
4b	23	2005 MHz	23	+ 2.7 / -12.7
4b	23	2005 MHz	23	+ 2.7 / -12.7
5 (Note 2)	23	2012.5 MHz	23	+ 2.7 / -14.7
5 (Note 3)	23	2012.5 MHz	23	+ 2.7 / -6.2
6 (Note 2)	23	2012.5 MHz	23	+ 2.7 / -14.7
6 (Note 3)	23	2012.5 MHz	23	+ 2.7 / -13.7
7	23	2012.5 MHz	23	+ 2.7 / -20.7
8 (Note 2)	23	2010 MHz	23	+ 2.7 / -26.7 (Note 1)
8 (Note 3)	23	2010 MHz	23	+ 2.7 / -25.7 (Note 1)
9 (Note 2)	23	2010 MHz	23	+ 2.7 / -27.7 (Note 1)
9 (Note 3)	23	2010 MHz	23	+ 2.7 / -26.7 (Note 1)
10 (Note 2)	23	2010 MHz	23	+ 2.7 / -27.7 (Note 1)
10 (Note 3)	23	2010 MHz	23	+ 2.7 / -21.7 (Note 1)
11	23	2010 MHz	23	+ 2.7 / -27.7 (Note 1)
Note 1: The output power within 2000-2005 MHz shall not be higher than 7.7 dBm Note 2: RB_start = RB# 0 Note 3: RB_start = RB# (max +1 – RB allocation)

Table 6.2.4_2.5-21: UE Power Class 3 test requirements (network signalled value "NS_21 for Band 30")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	3	3	0	17	5.0	25.7	11.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-22: UE Power Class Test requirements (network signalled value "NS_22")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	2	0	0	21	2.0	26.0	18.0
2	2	0	0	21	2.0	26.0	19.0
3	2	3	0	18	4.0	26.0	13.0
4	2	3	0	18	4.0	26.0	13.0
5	2	3	0	18	4.0	26.0	13.0
6	2	3	0	18	4.0	26.0	13.0
7	2	3	0	18	4.0	26.0	13.0
8	2	3	0	18	4.0	26.0	13.0
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-23: UE Power Class Test requirements (network signalled value "NS_23")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	2	0	0	21	2.0	21	2.0
2	2	0	0	21	2.0	21	2.0
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-24: UE Power Class 3 test requirements (network signalled value "NS_24”)

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	3	10	0	10	2.0	25.7	7.3
2	3	2	0	18	2.0	25.7	15.3
3	3	9	0	11	2.0	25.7	8.3
4	3	8	0	12	2.0	25.7	9.3
5	3	17	0	3	2.5	25.7	-0.2
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-25: UE Power Class 3 test requirements (network signalled value "NS_25")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	3	5	0	15	2.0	25.7	12.3
2	3	1	0	19	2.0	25.7	16.3
3	3	5	0	15	2.0	25.7	12.3
4	3	4	0	16	2.0	25.7	13.3
5	3	11	0	9	2.0	25.7	6.3
6	3	13	0	7	2.0	25.7	4.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-26: Reserved

Table 6.2.4_2.5-27: UE Power Class 3 test requirements (network signalled value "NS_27")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	MAX{T_L, T(P_{CMAX_L,c})} (dB)	Upper limit (dBm)	Lower limit (dBm)
1	3	0	0	20	3	26.0	16
2	3	0	0	20	3	26.0	16
3	3	2	0	18	4.0	26.0	13.0
4	3	3	0	17	5.0	26.0	11.0
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-28: UE Power Class 3 test requirements (network signalled value "NS_35")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	2	0	0	21	2	25.7	18.3
2	2	0	0	21	2	25.7	18.3
3	2	0	0	21	2	25.7	18.3
4	2	0	0	21	2	25.7	18.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-29: UE Power Class 3 test requirements (network signalled value "NS_36")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	3	4	0	16	5	25.7	10.3
2	3	0	0	20	2.5	25.7	16.8
3	3	10	0	10	6	25.7	3.3
4	3	0	0	20	2.5	25.7	16.8
5	3	10	0	10	6	25.7	3.3
6	3	0	0	20	2.5	25.7	16.8
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_2.5-30: UE Power Class 3 test requirements (network signalled value "NS_56")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	2	8	0	13	5	25.7	7.3
2	3	2	0	18	4	25.7	13.3
3	2	7	0	14	5	25.7	8.3
4	3	7	0	13	5	25.7	7.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.