6.2.4B Additional Maximum Power Reduction (A-MPR) for UL-MIMO
36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification
6.2.4B.1 Test purpose
Additional ACLR and spectrum emission requirements can be signalled by the network to indicate that the UE shall also meet additional requirements in a specific deployment scenario. To meet these additional requirements, Additional Maximum Power Reduction A-MPR is allowed for the sum output power at each antenna connector as specified in Table 6.2.2B.3-1. Unless stated otherwise, an A-MPR of 0 dB shall be used.
6.2.4B.2 Test applicability
The requirements of this test apply in test case 6.6.2.2 B Additional Spectrum Emission Mask for network signalled values NS_03, NS_04, NS_06, NS_07, NS_11, NS_20, NS_21, NS_27 and NS_35 to all types of E-UTRA UE release 10 and forward that support UL MIMO.
The requirements of this test apply in test case 6.6.3.3 B Additional Spurious Emissions for network signalled values NS_04, NS_05, NS_07, NS_08, NS_09, NS_12, NS_13, NS_14, NS_15, NS_16, NS_17, NS_18, NS_19, NS_21, NS_22, NS_23, NS_24, NS_25, NS_27, NS_36, NS_38, NS_39, NS_56 to all types of E-UTRA UE release 10 and forward that support UL MIMO.
NOTE: As a result TC 6.2.4B has not been included in the test case applicability table 4.1-1, TS 36.521-2. This does not preclude the test from being used for R&D or other purposes if deemed useful.
6.2.4B.3 Minimum conformance requirements
The minimum conformance requirements are defined in clause 6.2.4.3.
6.2.4B.4 Test description
6.2.4B.4.1 Initial condition
Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.
The initial test configurations consist of environmental conditions, test frequencies, and channel bandwidths based on E-UTRA operating bands specified in table 5.4.2.1-1. All of these configurations shall be tested with applicable test parameters for each channel bandwidth, and are shown in table 6.2.4B.4.1-1 through table 6.2.4B.4.1-23. The details of the uplink reference measurement channels (RMCs) are specified in Annex A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.
Table 6.2.4B.4.1-1: Test Configuration Table (network signalled value "NS_03")
|
Initial Conditions |
|||||||
|
Test Environment (as specified in TS 36.508 [7] clause 4.1) |
NC |
||||||
|
Test Frequencies (as specified in TS 36.508 [7] clause 4.3.1) |
Low range, Mid range, High range |
||||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] clause 4.3.1) |
Lowest, 5MHz, 10MHz, Highest |
||||||
|
Test Parameters for NS_03 A-MPR |
|||||||
|
Downlink Configuration |
Uplink Configuration |
||||||
|
Configuration ID |
Ch BW |
Mod’n |
RB allocation |
Mod’n |
RB allocation |
||
|
FDD |
TDD |
FDD |
TDD |
||||
|
1 |
1.4MHz |
N/A for A-MPR testing. |
QPSK |
6 |
6 |
||
|
2 |
1.4MHz |
QPSK |
5 |
5 |
|||
|
3 |
1.4MHz |
16QAM |
5 |
5 |
|||
|
4 |
3MHz |
QPSK |
15 |
15 |
|||
|
5 |
3MHz |
QPSK |
4 |
4 |
|||
|
6 |
3MHz |
16QAM |
15 |
15 |
|||
|
7 |
3MHz |
16QAM |
4 |
4 |
|||
|
8 |
5MHz |
QPSK |
25 |
25 |
|||
|
9 |
5MHz |
QPSK |
8 |
8 |
|||
|
10 |
5MHz |
QPSK |
6 |
6 |
|||
|
11 |
5MHz |
16QAM |
25 |
25 |
|||
|
12 |
5MHz |
16QAM |
8 |
8 |
|||
|
13 |
10MHz |
QPSK |
50 |
50 |
|||
|
14 |
10MHz |
QPSK |
12 |
12 |
|||
|
15 |
10MHz |
QPSK |
6 |
6 |
|||
|
16 |
10MHz |
16QAM |
50 |
50 |
|||
|
17 |
10MHz |
16QAM |
12 |
12 |
|||
|
18 |
15MHz |
QPSK |
75 |
75 |
|||
|
19 |
15MHz |
QPSK |
16 |
16 |
|||
|
20 |
15MHz |
QPSK |
8 |
8 |
|||
|
21 |
15MHz |
16QAM |
75 |
75 |
|||
|
22 |
15MHz |
16QAM |
16 |
16 |
|||
|
23 |
20MHz |
QPSK |
100 |
100 |
|||
|
24 |
20MHz |
QPSK |
18 |
18 |
|||
|
25 |
20MHz |
QPSK |
10 |
10 |
|||
|
26 |
20MHz |
16QAM |
100 |
100 |
|||
|
27 |
20MHz |
16QAM |
18 |
18 |
|||
|
Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in clause 6.2.4B.5 as not all combinations are necessarily required based on the applicability of the UE. Note 3: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 4: For band 23, above table only applies to mid and high range test frequencies. Low range test frequencies will be covered by NS_11 test configuration table. |
|||||||
Table 6.2.4B.4.1-2: Test Configuration Table (network signalled value "NS_04")
|
Initial Conditions |
||||||
|
Test Environment (as specified in TS 36.508 [7] subclause 4.1) |
NC |
|||||
|
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1) |
Low range, Mid range, High range Additional test frequencies for Rel-12 to Rel-13 and bit 2 of modifiedMPRbehavior = 0: For 5 MHz bandwidth: 2499.6 MHz, NUL= 39696 For 10 MHz bandwidth: 2504.1 MHz, NUL= 39731 For 15 MHz bandwidth: 2510.9 MHz, NUL= 39799 For 20 MHz bandwidth: 2517.6 MHz, NUL= 39866 Additional test frequencies for Rel-12 and later and bit 2 of modifiedMPRbehavior = 1: For 5 MHz bandwidth: 2500.6 MHz, NUL= 39686 For 10 MHz bandwidth: 2504.1 MHz, NUL= 39731 For 15 MHz bandwidth: 2510.9 MHz, NUL= 39799 For 20 MHz bandwidth: 2517.6 MHz, NUL= 39866 |
|||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1) |
5MHz, 10 MHz, 15 MHz, 20MHz |
|||||
|
Test Parameters for NS_04 A-MPR |
||||||
|
Downlink Configuration |
Uplink Configuration |
|||||
|
Configura-tion ID |
Ch BW |
Mod’n |
RB allocation TDD |
Mod’n |
RB allocation TDD |
RBstart TDD |
|
1 (Note 6) |
5MHz |
N/A for A-MPR testing |
QPSK |
25 |
0 |
|
|
2 (Note 6) |
5MHz |
QPSK |
8 |
Note 3 |
||
|
3(Note 6) |
5MHz |
QPSK |
6 |
Note 3 |
||
|
4 (Note 6) |
5MHz |
16QAM (Note 5) |
25 |
0 |
||
|
5 (Note 6) |
5MHz |
16QAM (Note 5) |
8 |
Note 3 |
||
|
6 (Note 6) |
10MHz |
QPSK |
1 |
0 |
||
|
7 (Note 6) |
10MHz |
QPSK |
12 |
0 |
||
|
8 (Note 6) |
10MHz |
QPSK |
50 |
0 |
||
|
9 Note 6) |
10MHz |
16QAM (Note 5) |
50 (Note 4) |
0 |
||
|
10 (Note 6) |
10MHz |
QPSK |
24 |
13 |
||
|
11 (Note 6) |
10MHz |
16QAM (Note 5) |
24 |
13 |
||
|
12 (Note 6) |
10MHz |
QPSK |
36 |
13 |
||
|
13 (Note 6) |
10MHz |
QPSK |
12 |
37 |
||
|
14 (Note 6) |
10MHz |
QPSK |
1 |
49 |
||
|
15 (Note 6) |
15MHz |
QPSK |
1 |
0 |
||
|
16 (Note 6) |
15MHz |
QPSK |
16 |
0 |
||
|
17 (Note 6) |
15MHz |
QPSK |
75 |
0 |
||
|
18 (Note 6) |
15MHz |
16QAM (Note 5) |
75 (Note 4) |
0 |
||
|
19 (Note 6) |
15MHz |
QPSK |
36 |
19 |
||
|
20 (Note 6) |
15MHz |
16QAM (Note 5) |
36 (Note 4) |
19 |
||
|
21 (Note 6) |
15MHz |
QPSK |
50 |
19 |
||
|
22 (Note 6) |
15MHz |
QPSK |
18 |
56 |
||
|
23 (Note 6) |
15MHz |
QPSK |
1 |
74 |
||
|
24 (Note 6) |
20MHz |
QPSK |
1 |
0 |
||
|
25 (Note 6) |
20MHz |
QPSK |
18 |
0 |
||
|
26 (Note 6) |
20MHz |
QPSK |
100 |
0 |
||
|
27 (Note 6) |
20MHz |
16QAM (Note 5) |
100 (Note 4) |
0 |
||
|
28 (Note 6) |
20MHz |
QPSK |
50 |
25 |
||
|
29 (Note 6) |
20MHz |
16QAM (Note 5) |
50 (Note 4) |
25 |
||
|
30 (Note 6) |
20MHz |
QPSK |
75 |
25 |
||
|
31 (Note 6) |
20MHz |
QPSK |
25 |
75 |
||
|
32 (Note 6) |
20MHz |
QPSK |
1 |
99 |
||
|
33 (Note 8) |
5MHz |
QPSK |
1 |
0 |
||
|
34 (Note 8) |
5MHz |
QPSK |
16 |
9 |
||
|
35 (Note 9) |
5MHz |
QPSK |
25 |
0 |
||
|
36 (Note 8) |
5MHz |
16QAM (Note 5) |
16 |
9 |
||
|
37 (Note 9) |
5MHz |
16QAM (Note 5) |
25 |
0 |
||
|
38 (Note 8) |
10MHz |
QPSK |
1 |
0 |
||
|
39 (Note 8) |
10MHz |
QPSK |
1 |
49 |
||
|
40 (Note 8) |
10MHz |
QPSK |
24 |
0 |
||
|
41 (Note 8) |
10MHz |
QPSK |
40 |
10 |
||
|
42 (Note 7) |
10MHz |
QPSK |
50 |
0 |
||
|
43 (Note 7) |
10MHz |
16QAM (Note 5) |
50 |
0 |
||
|
44 (Note 8) |
15MHz |
QPSK |
1 |
0 |
||
|
45 (Note 8) |
15MHz |
QPSK |
1 |
74 |
||
|
46 (Note 8) |
15MHz |
QPSK |
32 |
0 |
||
|
47 (Note 8) |
15MHz |
QPSK |
60 |
15 |
||
|
48 (Note 7) |
15MHz |
QPSK |
75 |
0 |
||
|
49 (Note 7) |
15MHz |
16QAM (Note 5) |
75 |
0 |
||
|
50 (Note 8) |
20MHz |
QPSK |
1 |
0 |
||
|
51 (Note 8) |
20MHz |
QPSK |
1 |
99 |
||
|
52 (Note 8) |
20MHz |
QPSK |
36 |
0 |
||
|
53 (Note 8) |
20MHz |
QPSK |
75 |
25 |
||
|
54 (Note 7) |
20MHz |
QPSK |
100 |
0 |
||
|
55 (Note 7) |
20MHz |
16QAM (Note 5) |
100 |
0 |
||
|
Note 1: Test Channel Bandwidths are checked separately for E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The configuration ID will be used to map the applicable Test Configuration to be corresponding Test Requirement in subclause 6.2.4 as not all combinations are necessarily required based on the applicability of the UE. Note 3: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 4: Applies only for UE-Categories ≥2. Note 5: Void. Note 6: Applies only for Rel-11 and earlier. Note 7: Applies only for Rel-12 and later. Note 8: Applies only for Rel-12 and later and Low Range. Note 9: Applies only for Rel-12 and later and Mid, High Range and additional test frequencies. |
||||||
Table 6.2.4B.4.1-3: Test Configuration Table (network signalled value "NS_05")
|
Initial Conditions |
||||||
|
Test Environment (as specified in TS 36.508 [7] subclause 4.1) |
Normal |
|||||
|
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1) |
Low range, Mid range In case of Low range: – For 5MHz Channel Bandwidth: 1927.2MHz (NUL = 18072) – For 10 MHz Channel Bandwidth: 1934.7 MHz (NUL = 18147) – For 15 MHz Channel Bandwidth: 1932.5 MHz (NUL = 18125) – For 20 MHz Channel Bandwidth: 1930 MHz (NUL = 18100) |
|||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1) |
5MHz, 10MHz, 15MHz, 20MHz |
|||||
|
Test Parameters for NS_05 A-MPR |
||||||
|
Downlink Configuration |
Uplink Configuration |
|||||
|
Configuration ID |
Ch BW |
Mod’n |
RB allocation FDD |
Mod’n |
RB allocation FDD |
RBstart FDD |
|
1 |
5MHz |
N/A for A-MPR testing |
QPSK |
1 |
0 |
|
|
2 |
5MHz |
QPSK |
1 |
24 |
||
|
3 |
5MHz |
QPSK |
25 |
0 |
||
|
4 |
10MHz |
QPSK |
1 |
0 |
||
|
5 |
10MHz |
QPSK |
1 |
49 |
||
|
6 |
10MHz |
QPSK |
12 |
0 |
||
|
7 |
10MHz |
QPSK |
12 |
37 |
||
|
8 |
10MHz |
QPSK |
48 |
0 |
||
|
9 |
10MHz |
QPSK |
48 |
2 |
||
|
10 (Note 5) |
10MHz |
QPSK |
50 |
0 |
||
|
11 (Note 5) |
10MHz |
16QAM |
50 (Note 4) |
0 |
||
|
12 (Note 6) |
15MHz |
QPSK |
1 |
8 |
||
|
13 (Note 6) |
15MHz |
QPSK |
1 |
66 |
||
|
14 (Note 6) |
15MHz |
QPSK |
16 |
8 |
||
|
15 (Note 6) |
15MHz |
QPSK |
16 |
51 |
||
|
16 (Note 6) |
15MHz |
QPSK |
30 |
8 |
||
|
17 (Note 6) |
15MHz |
QPSK |
30 |
38 |
||
|
18 (Note 6) |
20MHz |
QPSK |
1 |
24 |
||
|
19 (Note 6) |
20MHz |
QPSK |
1 |
75 |
||
|
20 (Note 6) |
20MHz |
QPSK |
18 |
24 |
||
|
21 (Note 6) |
20MHz |
QPSK |
18 |
58 |
||
|
22 (Note 6) |
20MHz |
QPSK |
24 |
24 |
||
|
23 (Note 6) |
20MHz |
QPSK |
24 |
52 |
||
|
24 (Note 7) |
15MHz |
QPSK |
1 |
0 |
||
|
25 (Note 7) |
15MHz |
QPSK |
1 |
74 |
||
|
26 (Note 7) |
15MHz |
QPSK |
16 |
0 |
||
|
27 (Note 7) |
15MHz |
QPSK |
16 |
59 |
||
|
28 (Note 7) |
15MHz |
QPSK |
48 |
0 |
||
|
29 (Note 7) |
15MHz |
QPSK |
48 |
27 |
||
|
30 (Note 7) |
15MHz |
QPSK |
75 |
0 |
||
|
31 (Note 7) |
15MHz |
16QAM |
75 (Note 4) |
0 |
||
|
32 (Note 7) |
20MHz |
QPSK |
1 |
0 |
||
|
33 (Note 7) |
20MHz |
QPSK |
1 |
99 |
||
|
34 (Note 7) |
20MHz |
QPSK |
18 |
0 |
||
|
35 (Note 7) |
20MHz |
QPSK |
18 |
82 |
||
|
36 (Note 7) |
20MHz |
QPSK |
48 |
0 |
||
|
37 (Note 7) |
20MHz |
QPSK |
48 |
52 |
||
|
38 (Note 7) |
20MHz |
QPSK |
100 |
0 |
||
|
39 (Note 7) |
20MHz |
16QAM |
100 (Note 4) |
0 |
||
|
40 (Note 8) |
10MHz |
QPSK |
50 |
0 |
||
|
41 (Note 8) |
10MHz |
16QAM |
50 (Note 4) |
0 |
||
|
42 (Note 8) |
15MHz |
QPSK |
1 |
0 |
||
|
43 (Note 8) |
15MHz |
QPSK |
75 |
0 |
||
|
44 (Note 8) |
15MHz |
QPSK |
16 |
8 |
||
|
45 (Note 8) |
15MHz |
QPSK |
30 |
8 |
||
|
46 (Note 8) |
15MHz |
QPSK |
54 |
8 |
||
|
47 (Note 8) |
15MHz |
QPSK |
64 |
8 |
||
|
48 (Note 8) |
15MHz |
QPSK |
1 |
74 |
||
|
49 (Note 8) |
15MHz |
QPSK |
6 |
69 |
||
|
50 (Note 8) |
15MHz |
QPSK |
8 |
67 |
||
|
51 (Note 8) |
20MHz |
QPSK |
1 |
0 |
||
|
52 (Note 8) |
20MHz |
QPSK |
100 |
0 |
||
|
53 (Note 8) |
20MHz |
QPSK |
18 |
24 |
||
|
54 (Note 8) |
20MHz |
QPSK |
24 |
24 |
||
|
55 (Note 8) |
20MHz |
QPSK |
40 |
24 |
||
|
56 (Note 8) |
20MHz |
QPSK |
50 |
24 |
||
|
57 (Note 8) |
20MHz |
QPSK |
72 |
24 |
||
|
58 (Note 8) |
20MHz |
QPSK |
1 |
99 |
||
|
59 (Note 8) |
20MHz |
QPSK |
6 |
94 |
||
|
60 (Note 8) |
20MHz |
QPSK |
24 |
76 |
||
|
61 (Note 9) |
10MHz |
QPSK |
50 |
0 |
||
|
62 (Note 9) |
10MHz |
16QAM |
50 (Note 4) |
0 |
||
|
63 (Note 9) |
15MHz |
QPSK |
1 |
0 |
||
|
64 (Note 9) |
15MHz |
QPSK |
1 |
74 |
||
|
65 (Note 9) |
15MHz |
QPSK |
16 |
0 |
||
|
66 (Note 9) |
15MHz |
QPSK |
16 |
59 |
||
|
67 (Note 9) |
15MHz |
QPSK |
48 |
0 |
||
|
68 (Note 9) |
15MHz |
QPSK |
48 |
27 |
||
|
69 (Note 9) |
15MHz |
QPSK |
75 |
0 |
||
|
70 (Note 9) |
15MHz |
16QAM |
75 (Note 4) |
0 |
||
|
71 (Note 9) |
20MHz |
QPSK |
1 |
0 |
||
|
72 (Note 9) |
20MHz |
QPSK |
1 |
99 |
||
|
73 (Note 9) |
20MHz |
QPSK |
18 |
0 |
||
|
74 (Note 9) |
20MHz |
QPSK |
18 |
82 |
||
|
75 (Note 9) |
20MHz |
QPSK |
48 |
0 |
||
|
76 (Note 9) |
20MHz |
QPSK |
48 |
52 |
||
|
77 (Note 9) |
20MHz |
QPSK |
100 |
0 |
||
|
78 (Note 9) |
20MHz |
16QAM |
100 (Note 4) |
0 |
||
|
Note 1: Void Note 2: Void Note 3: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 4: Applies only for UE-Categories ≥2. Note 5: Applies when bit number 1 in modifiedMPRbehavior = 0 (Rel-11 minimum requirements apply) for Band1 and not available for Band65. Note 6: Applies for low range and when bit number 1 in modifiedMPRbehavior = 0 (Rel-11 minimum requirements apply) for Band1 and not available for Band65. Note 7: Applies for mid range and when bit number 1 in modifiedMPRbehavior = 0 (Rel-11 minimum requirements apply) for Band1 and not available for Band65. Note 8: Applies only for low range and when bit number 1 in modifiedMPRbehavior = 1 (Rel-12 minimum requirements apply) for Band1 and low range for Band65. Note 9: Applies only for mid range and when bit number 1 in modifiedMPRbehavior = 1 (Rel-12 minimum requirements apply) for Band1 and mid range for Band65. Note 10: ModifiedMPRbehavior is defined in annex J.1. |
||||||
Table 6.2.4B.4.1-4: Test Configuration Table (network signalled value "NS_06")
|
Initial Conditions |
|||||
|
Test Environment (as specified in TS 36.508 [7] clause 4.1) |
Normal |
||||
|
Test Frequencies (as specified in TS 36.508 [7] clause 4.3.1) |
Low range, Mid range, High range |
||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] clause 4.3.1) |
Lowest, 5MHz, 10MHz, Highest |
||||
|
Test Parameters for NS_05 A-MPR |
|||||
|
Downlink Configuration |
Uplink Configuration |
||||
|
Configuration ID |
Ch BW |
Mod’n |
RB allocation FDD |
Mod’n |
RB allocation FDD |
|
1 |
1.4MHz |
N/A for A-MPR testing |
QPSK |
6 |
|
|
2 |
1.4MHz |
QPSK |
5 |
||
|
3 |
1.4MHz |
16QAM |
5 |
||
|
4 |
3MHz |
QPSK |
15 |
||
|
5 |
3MHz |
QPSK |
4 |
||
|
6 |
3MHz |
16QAM |
4 |
||
|
7 |
5MHz |
QPSK |
25 |
||
|
8 |
5MHz |
QPSK |
8 |
||
|
9 |
5MHz |
16QAM |
8 |
||
|
10 |
10MHz |
QPSK |
50 |
||
|
11 |
10MHz |
QPSK |
12 |
||
|
12 |
10MHz |
16QAM |
12 |
||
|
13 |
15MHz |
QPSK |
75 |
||
|
14 |
15MHz |
QPSK |
16 |
||
|
15 |
15MHz |
16QAM |
16 |
||
|
16 |
20MHz |
QPSK |
100 |
||
|
17 |
20MHz |
QPSK |
18 |
||
|
18 |
20MHz |
16QAM |
18 |
||
|
Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in clause 6.2.4B.5 as not all combinations are necessarily required based on the applicability of the UE. Note 3: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. |
|||||
Table 6.2.4B.4.1-5: Test Configuration Table (network signalled value "NS_07")
|
Initial Conditions |
||||||
|
Test Environment (as specified in TS 36.508 [7] clause 4.1) |
NC |
|||||
|
Test Frequencies (as specified in TS 36.508 [7] clause 4.3.1) |
Mid range |
|||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] clause 4.3.1) |
10MHz |
|||||
|
Test Parameters for NS_07 A-MPR |
||||||
|
Downlink Configuration |
Uplink Configuration |
|||||
|
Configuration ID |
Ch BW |
Mod’n |
RB allocation FDD |
Mod’n |
RB allocation FDD |
RBstart FDD |
|
1 |
10MHz |
N/A for A-MPR testing |
QPSK |
1 |
0 |
|
|
2 |
10MHz |
QPSK |
8 |
0 |
||
|
3 |
10MHz |
QPSK |
6 |
13 |
||
|
4 |
10MHz |
QPSK |
20 |
13 |
||
|
5 |
10MHz |
QPSK |
12 |
13 |
||
|
6 |
10MHz |
16QAM |
36 |
13 |
||
|
7 |
10MHz |
QPSK |
16 |
19 |
||
|
8 |
10MHz |
QPSK |
12 |
19 |
||
|
9 |
10MHz |
16QAM |
16 |
19 |
||
|
10 |
10MHz |
QPSK |
30 |
19 |
||
|
11 |
10MHz |
16QAM |
30 |
19 |
||
|
12 |
10MHz |
QPSK |
6 |
43 |
||
|
13 |
10MHz |
QPSK |
2 |
48 |
||
|
14 |
10MHz |
QPSK |
50 |
0 |
||
|
15 |
10MHz |
QPSK |
12 |
0 |
||
|
16 |
10MHz |
16QAM |
50 |
0 |
||
|
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in clause 6.2.4B.5 as not all combinations are necessarily required based on the applicability of the UE. |
||||||
Table 6.2.4B.4.1-6: Test Configuration Table (network signalled value "NS_08")
|
Initial Conditions |
|||||
|
Test Environment (as specified in TS 36.508 [7] clause 4.1) |
Normal |
||||
|
Test Frequencies (as specified in TS 36.508 [7] clause 4.3.1) |
High range |
||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] clause 4.3.1) |
5MHz, 10MHz, 15MHz |
||||
|
Test Parameters for NS_08 A-MPR |
|||||
|
Downlink Configuration |
Uplink Configuration |
||||
|
Configuration ID |
Ch BW |
Mod’n |
RB allocation FDD |
Mod’n |
RB allocation FDD |
|
1 |
5MHz |
N/A for A-MPR testing |
QPSK |
1 |
|
|
2 |
5MHz |
QPSK |
8 |
||
|
3 |
5MHz |
QPSK |
25 |
||
|
4 |
10MHz |
QPSK |
1 |
||
|
5 |
10MHz |
QPSK |
12 |
||
|
6 |
10MHz |
QPSK |
40 |
||
|
7 |
10MHz |
QPSK |
50 |
||
|
8 |
10MHz |
16QAM |
50 |
||
|
9 |
15MHz |
QPSK |
1 |
||
|
10 |
15MHz |
QPSK |
16 |
||
|
11 |
15MHz |
QPSK |
40 |
||
|
12 |
15MHz |
QPSK |
75 |
||
|
13 |
15MHz |
16QAM |
75 |
||
|
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in clause 6.2.4B.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 3: The RBstart of partial RB allocation shall be RB# 0 and RB# (max + 1 – RB allocation) of the channel bandwidth. |
|||||
Table 6.2.4B.4.1-7: Test Configuration Table (network signalled value “NS_09”)
|
Initial Conditions |
|||||
|
Test Environment (as specified in TS 36.508 [7] clause 4.1) |
Normal |
||||
|
Test Frequencies (as specified in TS 36.508 [7] clause 4.3.1) |
High range |
||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] clause 4.3.1) |
5MHz, 10MHz, 15MHz |
||||
|
Test Parameters for Channel Bandwidths |
|||||
|
Downlink Configuration |
Uplink Configuration |
||||
|
Configuration ID |
Ch BW |
Mod’n |
RB allocation FDD |
Mod’n |
RB allocation FDD |
|
1 |
5MHz |
N/A for A-MPR testing |
QPSK |
1 |
|
|
2 |
5MHz |
QPSK |
8 |
||
|
3 |
5MHz |
QPSK |
25 |
||
|
4 |
10MHz |
QPSK |
1 |
||
|
5 |
10MHz |
QPSK |
12 |
||
|
6 |
10MHz |
QPSK |
40 |
||
|
7 |
10MHz |
QPSK |
50 |
||
|
8 |
10MHz |
16QAM |
50 |
||
|
9 |
15MHz |
QPSK |
1 |
||
|
10 |
15MHz |
QPSK |
16 |
||
|
11 |
15MHz |
QPSK |
40 |
||
|
12 |
15MHz |
QPSK |
54 |
||
|
13 |
15MHz |
QPSK |
75 |
||
|
14 |
15MHz |
16QAM |
75 |
||
|
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in clause 6.2.4B.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 3: The RBstart of partial RB allocation shall be RB# 0 and RB# (max + 1 – RB allocation) of the channel bandwidth. |
|||||
Table 6.2.4B.4.1-8: Test Configuration Table (network signalled value "NS_11")
|
Initial Conditions |
|||||
|
Test Environment (as specified in TS 36.508 [7] clause 4.1) |
Normal |
||||
|
Test Frequencies (as specified in TS 36.508 [7] clause 4.3.1) |
Low range a. UL 2001.5 MHz (N_UL=25515), DL 2181.5 MHz(N_DL=7515) b UL 2004.5 MHz (N_UL=25545), DL 2184.5 (N_DL=7545) For 5 MHz Channel Bandwidth: a. UL 2002.5 MHz (N_UL=25525), DL 2182.5 MHz(N_DL=7525) b. UL 2004.5 MHz (N_UL=25545), DL 2184.5 MHz(N_DL=7545) c. UL 2007.5 MHz (N_UL=25575), DL 2187.5 MHz(N_DL=7575) For 10 MHz Channel Bandwidth: UL 2005 MHz (N_UL=25550), DL 2185 MHz (N_DL=7550) |
||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] clause 4.3.1) |
1.4MHz, 3MHz, 5MHz, 10MHz |
||||
|
Test Parameters for NS_11 A-MPR |
|||||
|
Downlink Configuration |
Uplink Configuration |
||||
|
Configuration ID |
Ch BW |
Mod’n |
RB allocation FDD |
Mod’n |
RB allocation FDD |
|
1 |
3MHz |
N/A for A-MPR testing |
QPSK |
6 |
|
|
2 |
3MHz |
QPSK |
15 |
||
|
3 |
3MHz |
16QAM |
6 |
||
|
4 |
3MHz |
16QAM |
15 |
||
|
5 |
5MHz |
QPSK |
1 |
||
|
6 |
5MHz |
QPSK |
8 |
||
|
7 |
5MHz |
QPSK |
25 |
||
|
8 |
5MHz |
16QAM |
8 |
||
|
9 |
5MHz |
16QAM |
25 |
||
|
10 |
10MHz |
QPSK |
1 |
||
|
11 |
10MHz |
QPSK |
12 |
||
|
12 |
10MHz |
QPSK |
50 |
||
|
13 |
10MHz |
16QAM |
12 |
||
|
14 |
10MHz |
16QAM |
50 |
||
|
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in clause 6.2.4B.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. |
|||||
Table 6.2.4B.4.1-9: Test Configuration Table (network signalled value "NS_12")
|
Initial Conditions |
||||||
|
Test Environment (as specified in TS 36.508 [7] clause 4.1) |
NC |
|||||
|
Test Frequencies (as specified in TS 36.508 [7] clause 4.3.1) |
For 1.4 MHz Channel Bandwidth: UL 814.9 MHz (NUL = 26699) For 3 MHz Channel Bandwidth: UL 815.7 MHz (NUL = 26707) For 5 MHz Channel Bandwidth: UL 816.7 MHz (NUL = 26717) For 10 MHz Channel Bandwidth: UL 819.2 MHz (NUL = 26742) For 15 MHz Channel Bandwidth: UL 821.7 MHz (NUL = 26767) |
|||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] clause 4.3.1) |
1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz |
|||||
|
Test Parameters for Channel Bandwidths |
||||||
|
Downlink Configuration |
Uplink Configuration |
|||||
|
Test Number |
Ch BW |
Mod’n |
RB allocation |
Mod’n |
RB allocation FDD |
RBstart FDD |
|
1 |
1.4 MHz |
N/A for A-MPR testing. |
QPSK |
1 |
0 |
|
|
2 |
1.4 MHz |
QPSK |
6 |
0 |
||
|
3 |
1.4 MHz |
QPSK |
1 |
1 |
||
|
4 |
1.4 MHz |
QPSK |
5 |
1 |
||
|
5 |
1.4 MHz |
16QAM |
6 |
0 |
||
|
6 (Note 1) |
3 MHz |
QPSK |
4 |
0 |
||
|
7 (Note 1) |
3 MHz |
QPSK |
6 |
0 |
||
|
8 |
3 MHz |
QPSK |
4 |
4 |
||
|
9 |
3 MHz |
QPSK |
6 |
4 |
||
|
10 (Note 1) |
3 MHz |
16QAM |
15 |
0 |
||
|
11 |
5 MHz |
QPSK |
8 |
0 |
||
|
12 |
5 MHz |
QPSK |
15 |
0 |
||
|
13 |
5 MHz |
QPSK |
8 |
7 |
||
|
14 (Note 1) |
5 MHz |
QPSK |
15 |
7 |
||
|
15 |
5 MHz |
16QAM |
25 |
0 |
||
|
16 (Note 2) |
10 MHz |
QPSK |
18 |
0 |
||
|
17 (Note 2) |
10 MHz |
QPSK |
18 |
16 |
||
|
18 (Note 2) |
10 MHz |
16QAM |
50 |
0 |
||
|
19 (Note 2) |
15 MHz |
QPSK |
30 |
0 |
||
|
20 (Note 2) |
15 MHz |
QPSK |
30 |
31 |
||
|
21 (Note 2) |
15 MHz |
16QAM |
75 |
0 |
||
|
Note 1: Only for UEs of Rel-11 and earlier Note 2: Only for UEs of Rel-12 and later |
||||||
Table 6.2.4B.4.1-10: Test Configuration Table (network signalled value "NS_13")
|
Initial Conditions |
||||||
|
Test Environment (as specified in TS 36.508 [7] clause 4.1) |
NC |
|||||
|
Test Frequencies (as specified in TS 36.508 [7] clause 4.3.1) |
For 1.4 MHz Channel Bandwidth: UL 819.7 MHz (NUL = 26747) For 3 MHz Channel Bandwidth: UL 820.5 MHz (NUL = 26755) For 5 MHz Channel Bandwidth: UL 821.5 MHz (NUL = 26765) |
|||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] clause 4.3.1) |
1.4 MHz, 3MHz and 5 MHz |
|||||
|
Test Parameters for Channel Bandwidths |
||||||
|
Downlink Configuration |
Uplink Configuration |
|||||
|
Test Number |
Ch BW |
Mod’n |
RB allocation |
Mod’n |
RB allocation FDD |
RBstart FDD |
|
1 (Note 1) |
1.4 MHz |
N/A for A-MPR testing. |
QPSK |
6 |
0 |
|
|
2 (Note 1) |
3 MHz |
QPSK |
15 |
0 |
||
|
3 |
5 MHz |
QPSK |
1 |
0 |
||
|
4 |
5 MHz |
QPSK |
25 |
0 |
||
|
5 |
5 MHz |
QPSK |
15 |
0 |
||
|
6 |
5 MHz |
QPSK |
15 |
7 |
||
|
7 |
5 MHz |
16QAM |
25 |
0 |
||
|
Note 1: Only for UEs of Rel-12 and later |
||||||
Table 6.2.4B.4.1-11: Test Configuration Table (network signalled value "NS_14")
|
Initial Conditions |
||||||
|
Test Environment (as specified in TS 36.508 [7] clause 4.1) |
NC |
|||||
|
Test Frequencies (as specified in TS 36.508 [7] clause 4.3.1) |
For 10 MHz Channel Bandwidth: UL 829 MHz (NUL = 26840) For 15 MHz Channel Bandwidth: Mid range |
|||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] clause 4.3.1) |
10 MHz, 15 MHz |
|||||
|
Test Parameters for Channel Bandwidths |
||||||
|
Downlink Configuration |
Uplink Configuration |
|||||
|
Test Number |
Ch BW |
Mod’n |
RB allocation |
Mod’n |
RB allocation FDD |
RBstart FDD |
|
1 |
10 MHz |
N/A for A-MPR testing. |
QPSK |
1 |
0 |
|
|
2 |
10 MHz |
QPSK |
25 |
0 |
||
|
3 |
10 MHz |
QPSK |
50 |
0 |
||
|
4 |
10 MHz |
QPSK |
25 |
1 |
||
|
5 |
10 MHz |
16QAM |
50 |
0 |
||
|
6 |
15 MHz |
QPSK |
8 |
0 |
||
|
7 |
15 MHz |
QPSK |
25 |
0 |
||
|
8 |
15 MHz |
QPSK |
75 |
0 |
||
|
9 |
15 MHz |
QPSK |
50 |
15 |
||
|
10 |
15 MHz |
16QAM |
75 |
0 |
||
Table 6.2.4B.4.1-12: Test Configuration Table (network signalled value "NS_15")
|
Initial Conditions |
||||||||||||
|
Test Environment (as specified in TS 36.508 [7] subclause 4.1) |
NC |
|||||||||||
|
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1) |
For 1.4 MHz Channel Bandwidth: High range For 3 MHz Channel Bandwidth: UL 843.5 MHz (NUL = 26985) or High range For 5 MHz Channel Bandwidth: UL 842.5 MHz (NUL = 26975) or High range For 10 MHz Channel Bandwidth: UL 840 MHz (NUL = 26950) or High range For 15 MHz Channel Bandwidth: UL 837.5 MHz (NUL = 26925) or High range |
|||||||||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1) |
1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz |
|||||||||||
|
Test Parameters for Channel Bandwidths |
||||||||||||
|
|
|
Downlink Configuration |
Uplink Configuration |
|||||||||
|
Configuration ID |
Ch BW |
Mod’n |
RB allocation |
Mod’n |
RB allocation FDD |
RBstart FDD |
||||||
|
1 (note 3) |
1.4 MHz |
N/A for A-MPR testing. |
QPSK |
4 |
0 |
|||||||
|
2 (note 3) |
1.4 MHz |
16QAM |
6 |
0 |
||||||||
|
3 (note 3) |
3 MHz |
QPSK |
6 |
7 |
||||||||
|
4 (note 3) |
3 MHz |
QPSK |
12 |
1 |
||||||||
|
5 (note 3) |
3 MHz |
16QAM |
15 |
0 |
||||||||
|
6 (note 2) |
3 MHz |
QPSK |
15 |
0 |
||||||||
|
7 (note 3) |
5 MHz |
QPSK |
6 |
14 |
||||||||
|
8 (note 3) |
5 MHz |
QPSK |
20 |
0 |
||||||||
|
9 (note 3) |
5 MHz |
16QAM |
25 |
0 |
||||||||
|
10 (note 2) |
5 MHz |
QPSK |
16 |
9 |
||||||||
|
11 (note 2) |
5 MHz |
QPSK |
25 |
0 |
||||||||
|
12 (note 3) |
10 MHz |
QPSK |
1 |
39 |
||||||||
|
13 (note 3) |
10 MHz |
QPSK |
1 |
10 |
||||||||
|
14 (note 3) |
10 MHz |
QPSK |
3 |
0 |
||||||||
|
15 (note 3) |
10 MHz |
QPSK |
20 |
3 |
||||||||
|
16 (note 3) |
10 MHz |
QPSK |
36 |
1 |
||||||||
|
17 (note 3) |
10 MHz |
QPSK |
50 |
0 |
||||||||
|
18 (note 1, 3) |
10 MHz |
16QAM |
50 |
0 |
||||||||
|
19 (note 2) |
10 MHz |
QPSK |
20 |
25 |
||||||||
|
20 (note 2) |
10 MHz |
QPSK |
45 |
0 |
||||||||
|
21 (note 3) |
15 MHz |
QPSK |
18 |
36 |
||||||||
|
22 (note 3) |
15 MHz |
QPSK |
25 |
1 |
||||||||
|
23 (note 3) |
15 MHz |
QPSK |
54 |
0 |
||||||||
|
24 (note 1, 3) |
15 MHz |
16QAM |
75 |
0 |
||||||||
|
25 (note 2) |
15 MHz |
QPSK |
18 |
44 |
||||||||
|
26 (note 2) |
15 MHz |
QPSK |
60 |
2 |
||||||||
|
Note 1: Applies only for UE-Categories ≥2. Note 2: Applicable only test frequency < high range Note 3: Applicable only to high range frequency testing |
||||||||||||
Table 6.2.4B.4.1-13: Test Configuration Table (network signalled value "NS_16")
|
Initial Conditions |
||||||
|
Test Environment (as specified in TS 36.508 [7] subclause 4.1) |
NC |
|||||
|
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1) |
For 1.4 MHz Channel Bandwidth: Low range For 3 MHz Channel Bandwidth: Low range, 810 MHz (NUL= 27070) For 5 MHz Channel Bandwidth: Low range, 811 MHz (NUL= 27080), 814.5 MHz (NUL= 27115) For 10 MHz Channel Bandwidth: Low range, 813.5 MHz (NUL= 27105), 817 MHz (NUL= 27140) |
|||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1) |
1.4 MHz, 3 MHz, 5 MHz, 10 MHz |
|||||
|
Test Parameters for Channel Bandwidths |
||||||
|
Downlink Configuration |
Uplink Configuration |
|||||
|
Configuration ID |
Ch BW |
Mod’n |
RB allocation |
Mod’n |
RB allocation FDD |
RBstart FDD |
|
1 |
1.4 MHz |
N/A for A-MPR testing. |
QPSK |
1 |
0 |
|
|
2 |
1.4 MHz |
QPSK |
6 |
0 |
||
|
3 |
1.4 MHz |
16QAM |
6 |
0 |
||
|
4 |
3 MHz |
QPSK |
1 |
0 |
||
|
5 |
3 MHz |
QPSK |
12 |
1 |
||
|
62 |
3 MHz |
QPSK |
15 |
0 |
||
|
7 |
3 MHz |
16QAM |
15 |
0 |
||
|
8 |
5 MHz |
QPSK |
1 |
0 |
||
|
95 |
5 MHz |
QPSK |
12 |
2 |
||
|
10 |
5 MHz |
QPSK |
18 |
2 |
||
|
11 |
5 MHz |
QPSK |
20 |
0 |
||
|
12 |
5 MHz |
QPSK |
20 |
2 |
||
|
13 |
5 MHz |
QPSK |
25 |
0 |
||
|
14 |
5 MHz |
16QAM |
25 |
0 |
||
|
15 |
10 MHz |
QPSK |
1 |
0 |
||
|
16 (Note 2) |
10 MHz |
QPSK |
1 |
10 |
||
|
17 (Note 2) |
10 MHz |
QPSK |
20 |
0 |
||
|
18 (Note 2) |
10 MHz |
QPSK |
27 |
15 |
||
|
19 (Note 2) |
10 MHz |
QPSK |
32 |
15 |
||
|
20 |
10 MHz |
QPSK |
32 |
0 |
||
|
21 |
10 MHz |
QPSK |
50 |
0 |
||
|
22 (Note 1) |
10 MHz |
16QAM |
50 |
0 |
||
|
23 (Note 3) |
10 MHz |
QPSK |
40 |
0 |
||
|
24 (Note 3) |
10 MHz |
QPSK |
40 |
1 |
||
|
Note 1: Applies only for UE-Categories ≥2. Note 2: Applies only for 10 MHz channel for Low Range, and 813.5 MHz Note 3: Applies only for 10 MHz channel for 817 MHz range |
||||||
Table 6.2.4B.4.1-14: Test Configuration Table (network signalled value "NS_20")
FFS
Table 6.2.4B.4.1-15: Test Configuration Table (network signalled value "NS_21")
|
Initial Conditions |
||||||||||||
|
Test Environment (as specified in TS 36.508 [7] subclause 4.1) |
NC |
|||||||||||
|
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1) |
Low range or High range |
|||||||||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1) |
5 MHz, 10 MHz |
|||||||||||
|
Test Parameters for Channel Bandwidths |
||||||||||||
|
Downlink Configuration |
Uplink Configuration |
|||||||||||
|
Configuration ID |
Ch BW |
Mod’n |
RB allocation |
Mod’n |
RB allocation FDD |
RBstart FDD |
||||||
|
1 (note 2) |
5 MHz |
QPSK |
1 |
0 |
||||||||
|
2 (note 2) |
5 MHz |
QPSK |
25 |
0 |
||||||||
|
3 (note 2) |
10 MHz |
QPSK |
1 |
0 |
||||||||
|
4 (note 3) |
10 MHz |
QPSK |
1 |
49 |
||||||||
|
5 (note 2) |
10 MHz |
QPSK |
15 |
0 |
||||||||
|
6 (note 3) |
10 MHz |
QPSK |
3 |
47 |
||||||||
|
7 (note 3) |
10 MHz |
QPSK |
50 |
0 |
||||||||
|
8 (note 1, 3) |
10 MHz |
16QAM |
50 |
0 |
||||||||
|
Note 1: Applies only for UE-Categories ≥2. Note 2: Applicable only to low range frequency testing. Note 3: Applicable only to high range frequency testing. |
||||||||||||
Table 6.2.4B.4.1-16: Test Configuration Table (network signalled value "NS_22")
|
Initial Conditions |
||||||
|
Test Environment (as specified in TS 36.508 [7] subclause 4.1) |
Normal |
|||||
|
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1) |
Low Range, Mid Range, High Range |
|||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1) |
5MHz, 10MHz, 15MHz, 20MHz |
|||||
|
Test Parameters for NS_22 A-MPR |
||||||
|
Downlink Configuration |
Uplink Configuration |
|||||
|
Configuration ID |
Ch BW |
Mod’n |
RB allocation FDD |
Mod’n |
RB allocation TDD |
RBstart TDD |
|
1 |
5MHz |
N/A for A-MPR testing |
QPSK |
1 |
0 |
|
|
2 |
5MHz |
QPSK |
25 |
0 |
||
|
3 |
5MHz |
QPSK |
1 |
24 |
||
|
4 |
5MHz |
16QAM |
1 |
0 |
||
|
5 |
5MHz |
16QAM |
1 |
24 |
||
|
6 |
10MHz |
QPSK |
50 |
0 |
||
|
7 |
10MHz |
QPSK |
36 |
0 |
||
|
8 |
10MHz |
QPSK |
1 |
0 |
||
|
9 |
10MHz |
QPSK |
1 |
49 |
||
|
10 |
10MHz |
16QAM |
1 |
0 |
||
|
11 |
10MHz |
16QAM |
1 |
49 |
||
|
12 |
15MHz |
QPSK |
75 |
0 |
||
|
13 |
15MHz |
QPSK |
50 |
0 |
||
|
14 |
15MHz |
QPSK |
1 |
0 |
||
|
15 |
15MHz |
QPSK |
1 |
74 |
||
|
16 |
15MHz |
16QAM |
1 |
0 |
||
|
17 |
15MHz |
16QAM |
1 |
74 |
||
|
18 |
20MHz |
QPSK |
100 |
0 |
||
|
19 |
20MHz |
QPSK |
64 |
0 |
||
|
20 |
20MHz |
QPSK |
1 |
0 |
||
|
21 |
20MHz |
QPSK |
1 |
99 |
||
|
22 |
20MHz |
16QAM |
1 |
0 |
||
|
23 |
20MHz |
16QAM |
1 |
99 |
||
Table 6.2.4B.4.1-17: Test Configuration Table (network signalled value "NS_23")
|
Initial Conditions |
||||||
|
Test Environment (as specified in TS 36.508 [7] subclause 4.1) |
Normal |
|||||
|
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1) |
Low Range, Mid Range, High Range |
|||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1) |
5MHz, 10MHz, 15MHz, 20MHz |
|||||
|
Test Parameters for NS_23 A-MPR |
||||||
|
Downlink Configuration |
Uplink Configuration |
|||||
|
Configuration ID |
Ch BW |
Mod’n |
RB allocation FDD |
Mod’n |
RB allocation TDD |
RBstart TDD |
|
1 |
5MHz |
N/A for A-MPR testing |
QPSK |
1 |
0 |
|
|
2 |
5MHz |
QPSK |
1 |
24 |
||
|
3 |
5MHz |
QPSK |
25 |
0 |
||
|
4 |
5MHz |
16QAM |
1 |
0 |
||
|
5 |
5MHz |
16QAM |
1 |
24 |
||
|
6 |
10MHz |
QPSK |
50 |
0 |
||
|
7 |
15MHz |
QPSK |
75 |
0 |
||
|
8 |
20MHz |
QPSK |
100 |
0 |
||
Table 6.2.4B.4.1-18: Test Configuration Table (network signalled value "NS_24")
|
Initial Conditions |
|||||||
|
Test Environment (as specified in TS 36.508 [7] subclause 4.1) |
Normal |
||||||
|
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1) |
Refer to FUL in test parameters with following: 5MHz CH BW:
10 and 15 MHz CH BW:
|
||||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1) |
5MHz, 10MHz, 15MHz, 20MHz |
||||||
|
Test Parameters for NS_24 A-MPR |
|||||||
|
Downlink Configuration |
Uplink Configuration |
||||||
|
Configuration ID |
FUL |
Ch BW |
Mod’n |
RB allocation FDD |
Mod’n |
RB allocation FDD |
RBstart FDD |
|
1 |
High |
5MHz |
N/A for A-MPR testing |
QPSK |
1 |
0 |
|
|
2 |
High |
5MHz |
QPSK |
8 |
17 |
||
|
3 |
High |
5MHz |
QPSK |
25 |
0 |
||
|
4 (Notes 2,3) |
High |
5MHz |
16QAM |
25 |
0 |
||
|
5 |
1985 |
5MHz |
QPSK |
8 |
17 |
||
|
6 |
1980 |
10MHz |
QPSK |
12 |
1 |
||
|
7 (Notes 2,3) |
1980 |
10MHz |
16QAM |
50 |
0 |
||
|
8 |
1980 |
10MHz |
QPSK |
48 |
2 |
||
|
9 |
1980 |
10MHz |
QPSK |
25 |
25 |
||
|
10 |
1980 |
10MHz |
QPSK |
1 |
49 |
||
|
11 |
1980 |
10MHz |
QPSK |
12 |
38 |
||
|
12 (Notes 2,3) |
1980 |
10MHz |
16QAM |
12 |
38 |
||
|
13 |
1980 |
10MHz |
QPSK |
3 |
47 |
||
|
14 |
1980 |
10MHz |
QPSK |
8 |
1 |
||
|
15 |
1990 |
10MHz |
QPSK |
1 |
0 |
||
|
16 |
1990 |
10MHz |
QPSK |
12 |
38 |
||
|
17 (Notes 2,3) |
1990 |
10MHz |
16QAM |
50 |
0 |
||
|
18 |
High |
10MHz |
QPSK |
12 |
38 |
||
|
19 |
High |
10MHz |
QPSK |
50 |
0 |
||
|
20 (Notes 2,3) |
High |
10MHz |
16QAM |
50 |
0 |
||
|
21 |
1980 |
15MHz |
QPSK |
1 |
11 |
||
|
22 |
1980 |
15MHz |
QPSK |
16 |
11 |
||
|
23 |
1980 |
15MHz |
QPSK |
45 |
11 |
||
|
24 (Notes 2,3) |
1980 |
15MHz |
16QAM |
50 |
0 |
||
|
25 |
1980 |
15MHz |
QPSK |
16 |
28 |
||
|
26 |
1980 |
15MHz |
QPSK |
16 |
59 |
||
|
27 |
1980 |
15MHz |
QPSK |
60 |
15 |
||
|
28 |
1980 |
15MHz |
QPSK |
30 |
12 |
||
|
29 |
High |
15MHz |
QPSK |
1 |
0 |
||
|
30 |
High |
15MHz |
QPSK |
16 |
59 |
||
|
31 (Notes 2,3) |
High |
15MHz |
16QAM |
16 |
59 |
||
|
32 (Notes 2,3) |
High |
15MHz |
16QAM |
75 |
0 |
||
|
33 |
High |
20MHz |
QPSK |
1 |
0 |
||
|
34 |
High |
20MHz |
QPSK |
18 |
82 |
||
|
35 (Notes 2,3) |
High |
20MHz |
16QAM |
18 |
82 |
||
|
36 (Notes 2,3) |
High |
20MHz |
16QAM |
100 |
0 |
||
|
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM. |
|||||||
Table 6.2.4B.4.1-19: Test Configuration Table (network signalled value "NS_25")
|
Initial Conditions |
|||||||
|
Test Environment (as specified in TS 36.508 [7] subclause 4.1) |
Normal |
||||||
|
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1) |
Refer to FUL in test parameters with following: 10 and 15 MHz CH BW:
|
||||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1) |
5MHz, 10MHz, 15MHz, 20MHz |
||||||
|
Test Parameters for NS_25 A-MPR |
|||||||
|
Downlink Configuration |
Uplink Configuration |
||||||
|
Configuration ID |
FUL |
Ch BW |
Mod’n |
RB allocation FDD |
Mod’n |
RB allocation FDD |
RBstart FDD |
|
1 |
High |
5MHz |
N/A for A-MPR testing |
QPSK |
25 |
0 |
|
|
2 (Notes 2,3) |
High |
5MHz |
16QAM |
25 |
0 |
||
|
3 |
High |
5MHz |
QPSK |
8 |
9 |
||
|
4 |
High |
5MHz |
QPSK |
1 |
24 |
||
|
5 |
High |
5MHz |
QPSK |
8 |
17 |
||
|
6 (Notes 2,3) |
High |
5MHz |
16QAM |
8 |
17 |
||
|
7 |
1980 |
10MHz |
QPSK |
12 |
1 |
||
|
8 (Notes 2,3) |
1980 |
10MHz |
16QAM |
50 |
0 |
||
|
9 (Notes 2,3) |
1980 |
10MHz |
16QAM |
48 |
2 |
||
|
10 |
1980 |
10MHz |
QPSK |
25 |
25 |
||
|
11 |
1980 |
10MHz |
QPSK |
1 |
49 |
||
|
12 |
1980 |
10MHz |
QPSK |
12 |
38 |
||
|
13 |
1990 |
10MHz |
QPSK |
12 |
0 |
||
|
14 |
1990 |
10MHz |
QPSK |
25 |
0 |
||
|
15 |
1990 |
10MHz |
QPSK |
50 |
0 |
||
|
16 (Notes 2,3) |
1990 |
10MHz |
16QAM |
25 |
0 |
||
|
17 |
1990 |
10MHz |
QPSK |
48 |
2 |
||
|
18 |
1990 |
10MHz |
QPSK |
30 |
19 |
||
|
19 (Notes 2,3) |
1990 |
10MHz |
16QAM |
30 |
19 |
||
|
20 |
1990 |
10MHz |
QPSK |
12 |
31 |
||
|
21 |
High |
10MHz |
QPSK |
1 |
0 |
||
|
22 |
High |
10MHz |
QPSK |
12 |
6 |
||
|
23 |
High |
10MHz |
QPSK |
50 |
0 |
||
|
24 (Notes 2,3) |
High |
10MHz |
16QAM |
50 |
0 |
||
|
25 |
High |
10MHz |
QPSK |
40 |
10 |
||
|
26 (Notes 2,3) |
High |
10MHz |
16QAM |
40 |
10 |
||
|
27 |
High |
10MHz |
QPSK |
32 |
18 |
||
|
28 (Notes 2,3) |
High |
10MHz |
16QAM |
32 |
18 |
||
|
29 |
High |
10MHz |
QPSK |
12 |
23 |
||
|
30 |
1980 |
15MHz |
QPSK |
16 |
4 |
||
|
31 |
1980 |
15MHz |
QPSK |
75 |
0 |
||
|
32 |
1980 |
15MHz |
QPSK |
60 |
15 |
||
|
33 (Notes 2,3) |
1980 |
15MHz |
16QAM |
40 |
35 |
||
|
34 |
1980 |
15MHz |
QPSK |
1 |
74 |
||
|
35 |
1980 |
15MHz |
QPSK |
12 |
63 |
||
|
36 |
1980 |
15MHz |
QPSK |
16 |
55 |
||
|
37 |
High |
15MHz |
QPSK |
1 |
0 |
||
|
38 |
High |
15MHz |
QPSK |
16 |
0 |
||
|
39 (Notes 2,3) |
High |
15MHz |
16QAM |
16 |
0 |
||
|
40 (Notes 2,3) |
High |
15MHz |
16QAM |
1 |
0 |
||
|
41 |
1980 |
20MHz |
QPSK |
1 |
0 |
||
|
42 |
1980 |
20MHz |
QPSK |
18 |
0 |
||
|
43 (Notes 2,3) |
1980 |
20MHz |
16QAM |
100 |
0 |
||
|
44 |
1980 |
20MHz |
QPSK |
64 |
36 |
||
|
45 |
1980 |
20MHz |
QPSK |
18 |
72 |
||
|
46 (Notes 2,3) |
1980 |
20MHz |
16QAM |
54 |
46 |
||
|
47 |
1980 |
20MHz |
QPSK |
18 |
55 |
||
|
48 |
High |
20MHz |
QPSK |
1 |
0 |
||
|
49 |
High |
20MHz |
QPSK |
18 |
72 |
||
|
50 (Notes 2,3) |
High |
20MHz |
16QAM |
18 |
72 |
||
|
51 (Notes 2,3) |
High |
20MHz |
16QAM |
100 |
0 |
||
|
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM. |
|||||||
Table 6.2.4B.4.1-20: Reserved
Table 6.2.4B.4.1-21: Test Configuration Table (network signalled value "NS_27")
|
Initial Conditions |
|||||||
|
Test Environment (as specified in TS 36.508 [7] subclause 4.1) |
Normal |
||||||
|
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1) |
Refer to Frequency column in test parameters |
||||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1) |
5MHz, 10MHz, 15MHz, 20MHz |
||||||
|
Test Parameters for NS_27 A-MPR |
|||||||
|
Downlink Configuration |
Uplink Configuration |
||||||
|
Configuration ID |
Frequency |
Ch BW |
Mod’n |
RB allocation FDD |
Mod’n |
RB allocation FDD |
RBstart FDD |
|
1 |
Low/Mid |
5MHz |
N/A for A-MPR testing |
QPSK |
1 |
0 |
|
|
2 |
High |
5MHz |
QPSK |
1 |
24 |
||
|
3 |
Low/Mid/High |
5MHz |
QPSK |
25 |
0 |
||
|
4 |
Low/Mid/High |
5MHz |
16QAM |
25 |
0 |
||
|
5 |
Low/Mid |
10MHz |
QPSK |
1 |
0 |
||
|
6 |
High |
10MHz |
QPSK |
1 |
49 |
||
|
7 |
Low/Mid/High |
10MHz |
QPSK |
50 |
0 |
||
|
8 (Note 2) |
Low/Mid/High |
10MHz |
16QAM |
50 |
0 |
||
|
9 |
Low/Mid |
15MHz |
QPSK |
1 |
0 |
||
|
10 |
Low |
15MHz |
QPSK |
1 |
7 |
||
|
11 |
Low/Mid |
15MHz |
QPSK |
16 |
0 |
||
|
12 |
High |
15MHz |
QPSK |
1 |
74 |
||
|
13 |
High |
15MHz |
QPSK |
1 |
67 |
||
|
14 |
High |
15MHz |
QPSK |
16 |
74 |
||
|
15 |
Low/Mid/High |
15MHz |
QPSK |
75 |
0 |
||
|
16 (Note 2) |
Low/Mid/High |
15MHz |
16QAM |
75 |
0 |
||
|
17 |
Low/Mid |
20MHz |
QPSK |
1 |
0 |
||
|
18 |
Low |
20MHz |
QPSK |
1 |
13 |
||
|
19 |
Low |
20MHz |
QPSK |
1 |
16 |
||
|
20 |
Low/Mid |
20MHz |
QPSK |
21 |
0 |
||
|
21 |
High |
20MHz |
QPSK |
1 |
99 |
||
|
22 |
High |
20MHz |
QPSK |
1 |
86 |
||
|
23 |
High |
20MHz |
QPSK |
1 |
83 |
||
|
24 |
High |
20MHz |
QPSK |
21 |
0 |
||
|
25 |
Low/Mid/High |
20MHz |
QPSK |
100 |
0 |
||
|
26 (Note 2) |
Low/Mid/High |
20MHz |
16QAM |
100 |
0 |
||
|
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4B.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM. |
|||||||
Table 6.2.4B.4.1-22: Test Configuration Table (network signalled value "NS_35")
|
Initial Conditions |
|||||
|
Test Environment (as specified in TS 36.508 [7] clause 4.1) |
Normal |
||||
|
Test Frequencies (as specified in TS 36.508 [7] clause 4.3.1) |
Low range, Mid range, High range |
||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] clause 4.3.1) |
5MHz, 10MHz, 15MHz, 20MHz |
||||
|
Test Parameters for NS_35 A-MPR |
|||||
|
Downlink Configuration |
Uplink Configuration |
||||
|
Configuration ID |
Ch BW |
Mod’n |
RB allocation FDD |
Mod’n |
RB allocation FDD |
|
1 |
5MHz |
N/A for A-MPR testing |
QPSK |
25 |
|
|
2 |
5MHz |
QPSK |
8 |
||
|
3 |
5MHz |
16QAM |
8 |
||
|
4 |
10MHz |
QPSK |
50 |
||
|
5 |
10MHz |
QPSK |
12 |
||
|
6 |
10MHz |
16QAM |
12 |
||
|
7 |
15MHz |
QPSK |
75 |
||
|
8 |
15MHz |
QPSK |
16 |
||
|
9 |
15MHz |
16QAM |
16 |
||
|
10 |
20MHz |
QPSK |
100 |
||
|
11 |
20MHz |
QPSK |
18 |
||
|
12 |
20MHz |
16QAM |
18 |
||
|
Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in clause 6.2.4B.5 as not all combinations are necessarily required based on the applicability of the UE. Note 3: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. |
|||||
Table 6.2.4B.4.1-23: Test Configuration Table (network signalled value "NS_36")
|
Initial Conditions |
|||||||
|
Test Environment (as specified in TS 36.508 [7] subclause 4.1) |
Normal |
||||||
|
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1) |
Refer to FUL in test parameters with following: 5 MHz CH BW:
10 MHz CH BW:
15 MHz CH BW:
|
||||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1) |
5MHz, 10MHz, 15MHz |
||||||
|
Test Parameters for NS_36 A-MPR |
|||||||
|
Downlink Configuration |
Uplink Configuration |
||||||
|
Configuration ID |
FUL |
Ch BW |
Mod’n |
RB allocation FDD |
Mod’n |
RB allocation FDD |
RBstart FDD |
|
1 |
700.5 |
5MHz |
N/A for A-MPR testing |
QPSK |
1 |
0 |
|
|
2 |
700.5 |
5MHz |
QPSK |
25 |
0 |
||
|
3 |
700.5 |
5MHz |
QPSK |
20 |
1 |
||
|
4 |
700.5 |
5MHz |
QPSK |
24 |
1 |
||
|
5 |
700.5 |
5MHz |
QPSK |
12 |
0 |
||
|
6 (Notes 2,3) |
700.5 |
5MHz |
16QAM |
12 |
0 |
||
|
7 |
705.5 |
5MHz |
QPSK |
25 |
0 |
||
|
8 (Notes 2,3) |
705.5 |
5MHz |
16QAM |
25 |
0 |
||
|
9 |
703 |
10MHz |
QPSK |
50 |
0 |
||
|
10 |
703 |
10MHz |
QPSK |
1 |
0 |
||
|
11 |
703 |
10MHz |
QPSK |
40 |
9 |
||
|
12 |
703 |
10MHz |
QPSK |
36 |
13 |
||
|
13 |
703 |
10MHz |
QPSK |
10 |
40 |
||
|
14 |
703 |
10MHz |
QPSK |
6 |
44 |
||
|
15 |
708 |
10MHz |
QPSK |
50 |
0 |
||
|
16 (Notes 2,3) |
708 |
10MHz |
16QAM |
50 |
0 |
||
|
17 |
705.5 |
15MHz |
QPSK |
75 |
0 |
||
|
18 |
705.5 |
15MHz |
QPSK |
50 |
17 |
||
|
19 |
705.5 |
15MHz |
QPSK |
50 |
24 |
||
|
20 |
705.5 |
15MHz |
QPSK |
1 |
57 |
||
|
21 |
705.5 |
15MHz |
QPSK |
10 |
17 |
||
|
22 |
705.5 |
15MHz |
QPSK |
18 |
24 |
||
|
23 (Notes 2,3) |
705.5 |
15MHz |
16QAM |
18 |
24 |
||
|
24 |
710.5 |
15MHz |
QPSK |
75 |
0 |
||
|
25 |
710.5 |
15MHz |
16QAM |
75 |
0 |
||
|
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM. |
|||||||
Table 6.2.4B.4.1-24: Test Configuration Table (network signalled value "NS_56")
|
Initial Conditions |
|||||||
|
Test Environment (as specified in TS 36.508 [7] subclause 4.1) |
Normal |
||||||
|
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1) |
Refer to FUL in test parameters with following: 5 MHz CH BW: 1630 MHz (low range) 10 MHz CH BW: 1632.5 MHz (low range) |
||||||
|
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1) |
5MHz, 10MHz |
||||||
|
Test Parameters for NS_56 A-MPR |
|||||||
|
Downlink Configuration |
Uplink Configuration |
||||||
|
Configuration ID |
FUL |
Ch BW |
Mod’n |
RB allocation FDD |
Mod’n |
RB allocation FDD |
RBstart FDD |
|
1 |
1630 |
5MHz |
N/A for A-MPR testing |
QPSK |
1 |
0 |
|
|
2 |
1630 |
5MHz |
QPSK |
25 |
0 |
||
|
3 (Notes 2,3) |
1630 |
5MHz |
16QAM |
25 |
0 |
||
|
4 |
1632.5 |
10MHz |
QPSK |
1 |
0 |
||
|
5 |
1632.5 |
10MHz |
QPSK |
12 |
0 |
||
|
6 |
1632.5 |
10MHz |
QPSK |
50 |
0 |
||
|
7 (Notes 2,3) |
1632.5 |
10MHz |
16QAM |
50 |
0 |
||
|
8 |
1632.5 |
10MHz |
QPSK |
1 |
6 |
||
|
9 |
1632.5 |
10MHz |
QPSK |
1 |
35 |
||
|
10 |
1632.5 |
10MHz |
QPSK |
1 |
40 |
||
|
11 |
1632.5 |
10MHz |
QPSK |
1 |
49 |
||
|
12 |
1632.5 |
10MHz |
QPSK |
15 |
35 |
||
|
13 |
1632.5 |
10MHz |
QPSK |
10 |
40 |
||
|
14 (Notes 2,3) |
1632.5 |
10MHz |
16QAM |
10 |
40 |
||
|
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4B.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM. |
|||||||
Editor’s note: The following lines belong at the end of section 6.2.4B.4.1. As new tables are added to this section, these lines should always follow the tables.
1. Connect the SS to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure A.3.
2. The parameter settings for the cell are set up according to TS 36.508 [7] clause 4.4.3.
3. Downlink signals are initially set up according to Annex C.0, C.1, and C.3.0, and uplink signals according to Annex H.1 and H.3.0.
4. The UL Reference Measurement channels are set according to the applicable table from Table 6.2.4B.4.1-1 to 6.2.4B.4.1-23.
5. Propagation conditions are set according to Annex B.0.
6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.2.4B.4.3.
6.2.4B.4.2 Test procedure
Same test procedure as in clause 6.2.4.4.2.
6.2.4B.4.3 Message contents
Message contents are according to TS 36.508 [7] clause 4.6, with exceptions as in clause 6.2.4.4.3.
6.2.4B.5 Test requirements
The maximum output power, derived in step 2 shall be within the range prescribed by the nominal maximum output power and tolerance in the applicable table from Table 6.2.4B.5-1 to Table 6.2.4B.5-27. The allowed A-MPR values specified in Table 6.2.4B.3-1 are in addition to the allowed MPR requirements specified in clause 6.2.3B. For the UE maximum output power modified by MPR and/or A-MPR, the power limits specified in Table 6.2.5B.3-1 apply.
Table 6.2.4B.5-1: UE Power Class test requirements (network signalled value "NS_03")
(for Bands 2 and 25)
|
Configuration ID |
EUTRA band |
Test Freq. |
Class 1 (dBm) |
Tol. (dB) |
Class 2 (dBm) |
Tol. (dB) |
Class 3 (dBm) |
Tol. (dB) |
|
1 |
2, 25 |
Mid |
23 |
+2.7 / -3.7 |
||||
|
1 |
2, 25 |
Low, High |
23 |
+2.7 / -5.7 |
||||
|
2 |
2, 25 |
Mid |
23 |
+2.7 / -2.7 |
||||
|
2 |
2, 25 |
Low, High |
23 |
+2.7 / -4.2 |
||||
|
3 |
2, 25 |
Mid |
23 |
+2.7 / -3.7 |
||||
|
3 |
2, 25 |
Low, High |
23 |
+2.7 / -5.7 |
||||
|
4 |
2, 25 |
Mid |
23 |
+2.7 / -4.7 |
||||
|
4 |
2, 25 |
Low, High |
23 |
+2.7 / -7.7 |
||||
|
5 |
2, 25 |
Mid |
23 |
+2.7 / -2.7 |
||||
|
5 |
2, 25 |
Low, High |
23 |
+2.7 / -4.2 |
||||
|
6 |
2, 25 |
Mid |
23 |
+2.7 / -6.2 |
||||
|
6 |
2, 25 |
Low, High |
23 |
+2.7 / -9.2 |
||||
|
7 |
2, 25 |
Mid |
23 |
+2.7 / -3.7 |
||||
|
7 |
2, 25 |
Low, High |
23 |
+2.7 / -5.7 |
||||
|
8 |
2, 25 |
All |
23 |
+2.7 / -4.7 |
||||
|
9 |
2, 25 |
Low @ RB#(max+1-RB allocation), Mid, High @ RB#0 |
23 |
+2.7 / -3.7 |
||||
|
9 |
2, 25 |
Low @ RB#0, High @ RB#(max+1-RB allocation) |
23 |
+2.7 / -5.7 |
||||
|
10 |
2, 25 |
Low @ RB#(max+1-RB allocation), Mid, High @ RB#0 |
23 |
+2.7 / -2.7 |
||||
|
10 |
2, 25 |
Low @ RB#0, High @ RB#(max+1-RB allocation) |
23 |
+2.7 / -4.2 |
||||
|
11 |
2, 25 |
All |
23 |
+2.7 / -6.2 |
||||
|
12 |
2, 25 |
Low @ RB#(max+1-RB allocation), Mid, High @ RB#0 |
23 |
+2.7 / -4.7 |
||||
|
12 |
2, 25 |
Low @ RB#0, High @ RB#(max+1-RB allocation) |
23 |
+2.7 / -7.7 |
||||
|
13 |
2, 25 |
All |
23 |
+2.7 / -4.7 |
||||
|
14 |
2, 25 |
Low @ RB#(max+1-RB allocation), Mid, High @ RB#0 |
23 |
+2.7 / -3.7 |
||||
|
14 |
2, 25 |
Low @ RB#0, High @ RB#(max+1-RB allocation) |
23 |
+2.7 / -5.7 |
||||
|
15 |
2, 25 |
Low @ RB#(max+1-RB allocation), Mid, High @ RB#0 |
23 |
+2.7 / -2.7 |
||||
|
15 |
2, 25 |
Low @ RB#0, High @ RB#(max+1-RB allocation) |
23 |
+2.7 / -4.2 |
||||
|
16 |
2, 25 |
All |
23 |
+2.7 / -6.2 |
||||
|
17 |
2, 25 |
Low @ RB#(max+1-RB allocation), Mid, High @ RB#0 |
23 |
+2.7 / -4.7 |
||||
|
17 |
2, 25 |
Low @ RB#0, High @ RB#(max+1-RB allocation) |
23 |
+2.7 / -7.7 |
||||
|
18 |
2, 25 |
All |
23 |
+2.7 / -4.7 |
||||
|
19 |
2, 25 |
Low @ RB#(max+1-RB allocation), Mid, High @ RB#0 |
23 |
+2.7 / -3.7 |
||||
|
19 |
2, 25 |
Low @ RB#0, High @ RB#(max+1-RB allocation) |
23 |
+2.7 / -5.7 |
||||
|
20 |
2, 25 |
Low @ RB#(max+1-RB allocation), Mid, High @ RB#0 |
23 |
+2.7 / -2.7 |
||||
|
20 |
2, 25 |
Low @ RB#0, High @ RB#(max+1-RB allocation) |
23 |
+2.7 / -4.2 |
||||
|
21 |
2, 25 |
All |
23 |
+2.7 / -6.2 |
||||
|
22 |
2, 25 |
Low @ RB#(max+1-RB allocation), Mid, High @ RB#0 |
23 |
+2.7 / -4.7 |
||||
|
22 |
2, 25 |
Low @ RB#0, High @ RB#(max+1-RB allocation) |
23 |
+2.7 / -7.7 |
||||
|
23 |
2, 25 |
All |
23 |
+2.7 / -4.7 |
||||
|
24 |
2, 25 |
All |
23 |
+2.7 / -3.7 |
||||
|
25 |
2, 25 |
Low @ RB#(max+1-RB allocation), Mid, High @ RB#0 |
23 |
+2.7 / -2.7 |
||||
|
25 |
2, 25 |
Low @ RB#0, High @ RB#(max+1-RB allocation) |
23 |
+2.7 / -4.2 |
||||
|
26 |
2, 25 |
All |
23 |
+2.7 / -6.2 |
||||
|
27 |
2, 25 |
All |
23 |
+2.7 / -4.7 |
Table 6.2.4B.5-2: UE Power Class test requirements (network signalled value "NS_03")
(for Bands 4, 10, 23, 35, 36, 66 and 70)
|
Configuration ID |
EUTRA band |
Class 1 (dBm) |
Tol. (dB) |
Class 2 (dBm) |
Tol. (dB) |
Class 3 (dBm) |
Tol. (dB) |
|
1 |
4,10, 23,35,36, 66 |
23 |
+2.7 / -3.7 |
||||
|
2 |
4,10, 23,35,36, 66 |
23 |
+2.7 / -2.7 |
||||
|
3 |
4,10, 23,35,36, 66 |
23 |
+2.7 / -3.7 |
||||
|
4 |
4,10, 23,35,36, 66 |
23 |
2.7 / -4.7 |
||||
|
5 |
4,10, 23,35,36, 66 |
23 |
+2.7 / -2.7 |
||||
|
6 |
4,10, 23,35,36, 66 |
23 |
+2.7 / -6.2 |
||||
|
7 |
4,10, 23,35,36, 66 |
23 |
+2.7 / -3.7 |
||||
|
8 |
4,10, 23,35,36, 66,70 |
23 |
2.7 / -4.7 |
||||
|
9 |
4,10, 23,35,36, 66,70 |
23 |
+2.7 / -3.7 |
||||
|
10 |
4,10, 23,35,36, 66,70 |
23 |
+2.7 / -2.7 |
||||
|
11 |
4,10, 23,35,36, 66,70 |
23 |
+2.7 / -6.2 |
||||
|
12 |
4,10, 23,35,36, 66,70 |
23 |
2.7 / -4.7 |
||||
|
13 |
4,10, 23,35,36, 66,70 |
23 |
2.7 / -4.7 |
||||
|
14 |
4,10, 23,35,36, 66,70 |
23 |
+2.7 / -3.7 |
||||
|
15 |
4,10, 23,35,36, 66,70 |
23 |
+2.7 / -2.7 |
||||
|
16 |
4,10, 23,35,36, 66,70 |
23 |
+2.7 / -6.2 |
||||
|
17 |
4,10, 23,35,36, 66,70 |
23 |
2.7 / -4.7 |
||||
|
18 |
4,10,35,36, 66,70 |
23 |
2.7 / -4.7 |
||||
|
19 |
4,10,35,36, 66,70 |
23 |
+2.7 / -3.7 |
||||
|
20 |
4,10,35,36, 66,70 |
23 |
+2.7 / -2.7 |
||||
|
21 |
4,10,35,36, 66,70 |
23 |
+2.7 / -6.2 |
||||
|
22 |
4,10,35,36, 66,70 |
23 |
2.7 / -4.7 |
||||
|
23 |
4,10,35,36, 66,70 |
23 |
2.7 / -4.7 |
||||
|
24 |
4,10,35,36, 66,70 |
23 |
+2.7 / -3.7 |
||||
|
25 |
4,10,35,36, 66,70 |
23 |
+2.7 / -2.7 |
||||
|
26 |
4,10,35,36, 66,70 |
23 |
+2.7 / -6.2 |
||||
|
27 |
4,10,35,36, 66,70 |
23 |
2.7 / -4.7 |
Table 6.2.4B.5-3: UE Power Class test requirements (network signalled value "NS_04")
|
Configuration ID |
MPR (dB) |
A-MPR (dB) |
ΔTC,c (dB) |
PCMAX,c (dBm) |
T(PCMAX_L,c) (dB) |
Upper limit (dBm) |
Lower limit (dBm) |
|
1 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
2 (RBstart=0; Low Range) |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
|
2 (RBstart=0; Mid, High Range) |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
|
2 (RBstart=17; Low, Mid Range) |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
|
2 (RBstart=17; High Range) |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
|
3 (RBstart=0; Low Range) |
15.8 |
15.8 |
15.8 |
15.8 |
15.8 |
15.8 |
15.8 |
|
3 (RBstart=0; Mid, High Range) |
19.3 |
19.3 |
19.3 |
19.3 |
19.3 |
19.3 |
19.3 |
|
3 (RBstart=19; Low, Mid Range) |
19.3 |
19.3 |
19.3 |
19.3 |
19.3 |
19.3 |
19.3 |
|
3 (RBstart=19; High Range) |
15.8 |
15.8 |
15.8 |
15.8 |
15.8 |
15.8 |
15.8 |
|
4 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
5 (RBstart=0; Low Range) |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
|
5 (RBstart=0; Mid, High Range) |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
5 (RBstart=17; Low, Mid Range) |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
5 (RBstart=17; High Range) |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
|
6 (Low Range) |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
|
6 (Mid, High Range) |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
7 (Low Range) |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
|
7 (Mid, High Range) |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
8 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
9 |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
|
10 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
|
11 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
12 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
13 (Low, Mid Range) |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
13 (High Range) |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
|
14 (Low, Mid Range) |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
14 (High Range) |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
|
15 (Low Range) |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
|
15 (Mid, High Range) |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
16 (Low, Mid Range) |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
|
16 (High Range) |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
17 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
18 |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
|
19 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
|
20 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
21 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
22 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
23 (Low, Mid Range) |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
23 (High Range) |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
|
24 (Low Range) |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
|
24 (Mid, High Range) |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
25 (Low Range) |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
|
25 (Mid, High Range) |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
26 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
27 |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
|
28 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
|
29 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
30 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
31 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
32 (Low, Mid Range) |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
32 (High Range) |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
|
33 |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
13.8 |
|
34 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
|
35 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
|
36 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
37 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
38 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
|
39 |
17.3 |
17.3 |
17.3 |
17.3 |
17.3 |
17.3 |
17.3 |
|
40 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
41 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
42 (Low Range) |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
42 (Mid, High Range, 2504.1 MHz) |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
|
43 (Low Range) |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
43 (Mid, High Range, 2504.1 MHz ) |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
44 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
|
45 |
17.3 |
17.3 |
17.3 |
17.3 |
17.3 |
17.3 |
17.3 |
|
46 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
47 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
48 (Low Range) |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
48 (Mid, High Range, 2510.9 MHz) |
-0.7 |
-0.7 |
-0.7 |
-0.7 |
-0.7 |
-0.7 |
-0.7 |
|
49 (Low Range) |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
|
49 (Mid, High Range, 2510.9 MHz) |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
|
50 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
51 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
12.8 |
|
52 |
17.3 |
17.3 |
17.3 |
17.3 |
17.3 |
17.3 |
17.3 |
|
53 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
54 (Low Range) |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
15.3 |
|
54 (Mid, High Range, 2517.6 MHz) |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
13.3 |
|
55 (Low Range) |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
16.3 |
|
55 (Mid, High Range, 2517.6 MHz) |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
12.3 |
|
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1. |
|||||||
Table 6.2.4B.5-4: UE Power Class test requirements (network signalled value "NS_05")
|
Configuration ID |
MPR (dB) |
A-MPR (dB) |
ΔTC,c (dB) |
PCMAX,c (dBm) |
T(PCMAX_L,c) (dB) |
Upper limit (dBm) |
Lower limit (dBm) |
|
1 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
2 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
3 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
4 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
5 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
6 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
7 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
8 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
9 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
10 |
1 |
1 |
0 |
21 |
5.0 |
25.7 |
15.3 |
|
11 |
2 |
1 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
12 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
13 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
14 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
15 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
16 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
17 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
18 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
19 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
20 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
21 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
22 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
23 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
24 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
25 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
26 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
27 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
28 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
29 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
30 |
1 |
1 |
0 |
21 |
5.0 |
25.7 |
15.3 |
|
31 |
2 |
1 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
32 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
33 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
34 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
35 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
36 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
37 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
38 |
1 |
1 |
0 |
21 |
5.0 |
25.7 |
15.3 |
|
39 |
2 |
1 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
40 |
1 |
1 |
0 |
21 |
5.0 |
25.7 |
15.3 |
|
41 |
2 |
1 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
42 |
0 |
11 |
0 |
12 |
6.0 |
25.7 |
5.3 |
|
43 |
1 |
11 |
0 |
11 |
6.0 |
25.7 |
4.3 |
|
44 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
45 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
46 |
1 |
3 |
0 |
19 |
5.0 |
25.7 |
13.3 |
|
47 |
1 |
5 |
0 |
17 |
5.0 |
25.7 |
11.3 |
|
48 |
0 |
5 |
0 |
18 |
5.0 |
25.7 |
12.3 |
|
49 |
0 |
5 |
0 |
18 |
5.0 |
25.7 |
12.3 |
|
50 |
0 |
1 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
51 |
0 |
11 |
0 |
12 |
6.0 |
25.7 |
5.3 |
|
52 |
1 |
11 |
0 |
11 |
6.0 |
25.7 |
4.3 |
|
53 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
54 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
55 |
1 |
3 |
0 |
19 |
5.0 |
25.7 |
13.3 |
|
56 |
1 |
5 |
0 |
17 |
5.0 |
25.7 |
11.3 |
|
57 |
1 |
10 |
0 |
12 |
6.0 |
25.7 |
5.3 |
|
58 |
0 |
5 |
0 |
18 |
5.0 |
25.7 |
12.3 |
|
59 |
0 |
5 |
0 |
18 |
5.0 |
25.7 |
12.3 |
|
60 |
1 |
1 |
0 |
21 |
5.0 |
25.7 |
15.3 |
|
61 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
62 |
2 |
0 |
0 |
21 |
5.0 |
25.7 |
15.3 |
|
63 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
64 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
65 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
66 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
67 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
68 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
69 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
70 |
2 |
0 |
0 |
21 |
5.0 |
25.7 |
15.3 |
|
71 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
72 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
73 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
74 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
75 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
76 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
77 |
1 |
1 |
0 |
21 |
5.0 |
25.7 |
15.3 |
|
78 |
2 |
1 |
0 |
20 |
6.0 |
25.7 |
13.3 |
Table 6.2.4B.5-5: UE Power Class test requirements (network signalled value "NS_06")
(for Band 12)
|
Configuration ID |
EUTRA band |
Test Freq. |
Class 1 (dBm) |
Tol. (dB) |
Class 2 (dBm) |
Tol. (dB) |
Class 3 (dBm) |
Tol. (dB) |
|
1 |
12 |
Mid |
23 |
+2.7 / -3.7 |
||||
|
1 |
12 |
Low, High |
23 |
+2.7 / -5.7 |
||||
|
2 |
12 |
Mid |
23 |
+2.7 / -2.7 |
||||
|
2 |
12 |
Low, High |
23 |
+2.7 / -4.2 |
||||
|
3 |
12 |
Mid |
23 |
+2.7 / -2.7 |
||||
|
3 |
12 |
Low, High |
23 |
+2.7 / -4.2 |
||||
|
4 |
12 |
Mid |
23 |
+2.7 / -3.7 |
||||
|
4 |
12 |
Low, High |
23 |
+2.7 / -5.7 |
||||
|
5 |
12 |
Mid |
23 |
+2.7 / -2.7 |
||||
|
5 |
12 |
Low, High |
23 |
+2.7 / -4.2 |
||||
|
6 |
12 |
Mid |
23 |
+2.7 / -3.7 |
||||
|
6 |
12 |
Low, High |
23 |
+2.7 / -5.7 |
||||
|
7 |
12 |
All |
23 |
+2.7 / -3.7 |
||||
|
8 |
12 |
Low @ RB#(max+1-RB allocation), Mid, High @ RB#0 |
23 |
+2.7 / -2.7 |
||||
|
8 |
12 |
Low @ RB#0, High @ RB#(max+1-RB allocation) |
23 |
+2.7 / -4.2 |
||||
|
9 |
12 |
Low @ RB#(max+1-RB allocation), Mid, High @ RB#0 |
23 |
+2.7 / -3.7 |
||||
|
9 |
12 |
Low @ RB#0, High @ RB#(max+1-RB allocation) |
23 |
+2.7 / -5.7 |
||||
|
10 |
12 |
All |
23 |
+2.7 / -3.7 |
||||
|
11 |
12 |
Low @ RB#(max+1-RB allocation), Mid, High @ RB#0 |
23 |
+2.7 / -2.7 |
||||
|
11 |
12 |
Low @ RB#0, High @ RB#(max+1-RB allocation) |
23 |
+2.7 / -4.2 |
||||
|
12 |
12 |
Low @ RB#(max+1-RB allocation), Mid, High @ RB#0 |
23 |
+2.7 / -3.7 |
||||
|
12 |
12 |
Low @ RB#0, High @ RB#(max+1-RB allocation) |
23 |
+2.7 / -5.7 |
Table 6.2.4B.5-6: UE Power Class test requirements (network signalled value "NS_06")
(for Bands 13, 14, and 17)
|
Configuration ID |
EUTRA band |
Class 1 (dBm) |
Tol. (dB) |
Class 2 (dBm) |
Tol. (dB) |
Class 3 (dBm) |
Tol. (dB) |
|
1 |
13,14,17 |
23 |
+2.7 / -3.7 |
||||
|
2 |
13,14,17 |
23 |
+2.7 / -2.7 |
||||
|
3 |
13,14,17 |
23 |
+2.7 / -2.7 |
||||
|
4 |
13,14,17 |
23 |
+2.7 / -3.7 |
||||
|
5 |
13,14,17 |
23 |
+2.7 / -2.7 |
||||
|
6 |
13,14,17 |
23 |
+2.7 / -3.7 |
||||
|
7 |
13,14,17 |
23 |
+2.7 / -3.7 |
||||
|
8 |
13,14,17 |
23 |
+2.7 / -2.7 |
||||
|
9 |
13,14,17 |
23 |
+2.7 / -3.7 |
||||
|
10 |
13,14,17 |
23 |
+2.7 / -3.7 |
||||
|
11 |
13,14,17 |
23 |
+2.7 / -2.7 |
||||
|
12 |
13,14,17 |
23 |
+2.7 / -3.7 |
||||
|
13 |
13,14,17 |
23 |
+2.7 / -3.7 |
||||
|
14 |
13,14,17 |
23 |
+2.7 / -2.7 |
||||
|
15 |
13,14,17 |
23 |
+2.7 / -3.7 |
||||
|
16 |
13,14,17 |
23 |
+2.7 / -3.7 |
||||
|
17 |
13,14,17 |
23 |
+2.7 / -2.7 |
||||
|
18 |
13,14,17 |
23 |
+2.7 / -3.7 |
Table 6.2.4B.5-7: UE Power Class test requirements (network signalled value "NS_07")
|
Configuration ID |
EUTRA band |
Class 1 (dBm) |
Tol. (dB) |
Class 2 (dBm) |
Tol. (dB) |
Class 3 (dBm) |
Tol. (dB) |
|
1 |
13 |
23 |
+2.7 / -18.7 |
||||
|
2 |
13 |
23 |
+2.7 / -13.7 |
||||
|
3 |
13 |
23 |
+2.7 / -2.7 |
||||
|
4 |
13 |
23 |
+2.7 / -19.7 |
||||
|
5 |
13 |
23 |
+2.7 / -18.7 |
||||
|
6 |
13 |
23 |
+2.7 / -20.7 |
||||
|
7 |
13 |
23 |
+2.7 / -3.7 |
||||
|
8 |
13 |
23 |
+2.7 / -2.7 |
||||
|
9 |
13 |
23 |
+2.7 / -4.7 |
||||
|
10 |
13 |
23 |
+2.7 / -12.7 |
||||
|
11 |
13 |
23 |
+2.7 / -13.7 |
||||
|
12 |
13 |
23 |
+2.7 / -2.7 |
||||
|
13 |
13 |
23 |
+2.0 / -5.5±TT |
||||
|
14 |
13 |
23 |
+2.7 / -19.7 |
||||
|
15 |
13 |
23 |
+2.7 / -18.7 |
||||
|
16 |
13 |
23 |
+2.7 / -20.7 |
Table 6.2.4B.5-8: UE Power Class test requirements (network signalled value "NS_08")
|
Configuration ID |
EUTRA band |
Class 1 (dBm) |
Tol. (dB) |
Class 2 (dBm) |
Tol. (dB) |
Class 3 (dBm) |
Tol. (dB) |
|
1 |
19 |
23 |
+2.7 / -2.7 |
||||
|
2 |
19 |
23 |
+2.7 / -2.7 |
||||
|
3 |
19 |
23 |
+2.7 / -3.7 |
||||
|
4 |
19 |
23 |
+2.7 / -2.7 |
||||
|
5 |
19 |
23 |
+2.7 / -2.7 |
||||
|
6 |
19 |
23 |
+2.7 / -3.7 |
||||
|
7 |
19 |
23 |
+2.7 / -8.2 |
||||
|
8 |
19 |
23 |
+2.7 / -9.7 |
||||
|
9 |
19 |
23 |
+2.7 / -2.7 |
||||
|
10 |
19 |
23 |
+2.7 / -2.7 |
||||
|
11 |
19 |
23 |
+2.7 / -3.7 |
||||
|
12 |
19 |
23 |
+2.7 / -8.2 |
||||
|
13 |
19 |
23 |
+2.7 / -9.7 |
Table 6.2.4B.5-9: UE Power Class test requirements (network signalled value "NS_09")
|
Configuration ID |
EUTRA band |
Class 1 (dBm) |
Tol. (dB) |
Class 2 (dBm) |
Tol. (dB) |
Class 3 (dBm) |
Tol. (dB) |
|
1 |
21 |
23 |
+2.7 / -2.7 |
||||
|
2 |
21 |
23 |
+2.7 / -2.7 |
||||
|
3 |
21 |
23 |
+2.7 / -3.7 |
||||
|
4 |
21 |
23 |
+2.7 / -2.7 |
||||
|
5 |
21 |
23 |
+2.7 / -2.7 |
||||
|
6 |
21 |
23 |
+2.7 / -3.7 |
||||
|
7 |
21 |
23 |
+2.7 / -4.7 |
||||
|
8 |
21 |
23 |
+2.7 / -6.2 |
||||
|
9 |
21 |
23 |
+2.7 / -2.7 |
||||
|
19 |
21 |
23 |
+2.7 / -2.7 |
||||
|
11 |
21 |
23 |
+2.7 / -3.7 |
||||
|
12 |
21 |
23 |
+2.7 / -4.7 |
||||
|
13 |
21 |
23 |
+2.7 / -6.2 |
||||
|
14 |
21 |
23 |
+2.7 / -8.2 |
Table 6.2.4B.5-10: UE Power Class test requirements (network signalled value "NS_11 for Band 23")
|
Configuration ID |
EUTRA band |
Centre Frequency |
Class 1 (dBm) |
Tol. (dB) |
Class 2 (dBm) |
Tol. (dB) |
Class 3 (dBm) |
Tol. (dB) |
|
1a |
23 |
UL 2001.5 MHz DL 2181.5 MHz |
+2.7 / -11.7 |
|||||
|
1b |
23 |
UL 2004.5 MHz DL 2184.5 MHz |
+2.7 / -4.7 |
|||||
|
2a |
23 |
UL 2001.5 MHz DL 2181.5 MHz |
+2.7 / -11.7 |
|||||
|
2b |
23 |
UL 2004.5 MHz DL 2184.5 MHz |
+2.7 / -4.7 |
|||||
|
3a |
23 |
UL 2001.5 MHz DL 2181.5 MHz |
+2.7 / -12.7 |
|||||
|
3b |
23 |
UL 2004.5 MHz DL 2184.5 MHz |
+2.7 / -6.2 |
|||||
|
4a |
23 |
UL 2001.5 MHz DL 2181.5 MHz |
+2.7 / -12.7 |
|||||
|
4b |
23 |
UL 2004.5 MHz DL 2184.5 MHz |
+2.7 / -6.2 |
|||||
|
5a |
23 |
UL 2002.5 MHz DL 2182.5 MHz |
+2.7 / -12.7 |
|||||
|
5b |
23 |
UL 2004.5 MHz DL 2184.5 MHz |
+2.7 / -8.2 |
|||||
|
5c |
23 |
UL 2007.5 MHz DL 2187.5 MHz |
+2.7 / -2.7 |
|||||
|
6a |
23 |
UL 2002.5 MHz DL 2182.5 MHz |
+2.7 / -12.7 |
|||||
|
6b |
23 |
UL 2004.5 MHz DL 2184.5 MHz |
+2.7 / -2.7 |
|||||
|
6c |
23 |
UL 2007.5 MHz DL 2187.5 MHz |
+2.7 / -3.7 |
|||||
|
7a |
23 |
UL 2002.5 MHz DL 2182.5 MHz |
+2.7 / -13.7 |
|||||
|
7b |
23 |
UL 2004.5 MHz DL 2184.5 MHz |
+2.7 / -9.7 |
|||||
|
7c |
23 |
UL 2007.5 MHz DL 2187.5 MHz |
+2.7 / -4.7 |
|||||
|
8a |
23 |
UL 2002.5 MHz DL 2182.5 MHz |
+2.7 / -13.7 |
|||||
|
8b |
23 |
UL 2004.5 MHz DL 2184.5 MHz |
+2.7 / -3.7 |
|||||
|
8c |
23 |
UL 2007.5 MHz DL 2187.5 MHz |
+2.7 / -4.7 |
|||||
|
9a |
23 |
UL 2002.5 MHz DL 2182.5 MHz |
+2.7 / -14.7 |
|||||
|
9b |
23 |
UL 2004.5 MHz DL 2184.5 MHz |
+2.7 / -11.7 |
|||||
|
9c |
23 |
UL 2007.5 MHz DL 2187.5 MHz |
+2.7 / -6.2 |
|||||
|
10 |
23 |
UL 2005 MHz DL 2185 MHz |
+2.7 / -18.7 |
|||||
|
11 |
23 |
UL 2005 MHz DL 2185 MHz |
+2.7 / -18.7 |
|||||
|
12 |
23 |
UL 2005 MHz DL 2185 MHz |
+2.7 / -19.7 |
|||||
|
13 |
23 |
UL 2005 MHz DL 2185 MHz |
+2.7 / -19.7 |
|||||
|
14 |
23 |
UL 2005 MHz DL 2185 MHz |
+2.7 / -20.7 |
Table 6.2.4B.5-11: UE Power Class test requirements (network signalled value "NS_12")
|
Configuration ID |
MPR (dB) |
A-MPR (dB) |
ΔTC,c (dB) |
PCMAX,c (dBm) |
T(PCMAX_L,c) (dB) |
Upper limit (dBm) |
Lower limit (dBm) |
|
1 |
0 |
3 |
1.5 |
18.5 |
4 |
25.7 |
13.8 |
|
2 |
1 |
4 |
1.5 |
16.5 |
5 |
25.7 |
10.8 |
|
3 |
0 |
0 |
1.5 |
21.5 |
3 |
25.7 |
17.8 |
|
4 |
0 |
3 |
1.5 |
18.5 |
4 |
25.7 |
13.8 |
|
5 |
2 |
4 |
1.5 |
15.5 |
5 |
25.7 |
9.8 |
|
6 |
0 |
4 |
1.5 |
17.5 |
5 |
25.7 |
11.8 |
|
7 |
1 |
3 |
1.5 |
17.5 |
5 |
25.7 |
11.8 |
|
8 |
0 |
0 |
1.5 |
21.5 |
3 |
25.7 |
17.8 |
|
9 |
1 |
3 |
1.5 |
17.5 |
5 |
25.7 |
11.8 |
|
10 |
2 |
4 |
1.5 |
15.5 |
5 |
25.7 |
9.8 |
|
11 |
0 |
4 |
1.5 |
17.5 |
5 |
25.7 |
11.8 |
|
12 |
1 |
3 |
1.5 |
17.5 |
5 |
25.7 |
11.8 |
|
13 |
0 |
0 |
1.5 |
21.5 |
3 |
25.7 |
17.8 |
|
14 |
1 |
3 |
0 |
19 |
3,5 |
25.7 |
14.8 |
|
15 |
2 |
3 |
0 |
18 |
4 |
25.7 |
13.3 |
|
16 |
1 |
4 |
1.5 |
16.5 |
5 |
25.7 |
10.8 |
|
17 |
1 |
0 |
0 |
22 |
3 |
25.7 |
18.3 |
|
18 |
2 |
2 |
0 |
19 |
3 |
25.7 |
15.3 |
|
19 |
1 |
4 |
0 |
18 |
4 |
25.7 |
13.3 |
|
20 |
1 |
0 |
0 |
22 |
3 |
25.7 |
18.3 |
|
21 |
2 |
3 |
0 |
18 |
4 |
25.7 |
13.3 |
|
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1. |
|||||||
Table 6.2.4B.5-12: UE Power Class test requirements (network signalled value "NS_13")
|
Configuration ID |
MPR (dB) |
A-MPR (dB) |
TC,c (dB) |
PCMAX,c (dBm) |
T(PCMAX_L,c) (dB) |
Upper limit (dBm) |
Lower limit (dBm) |
|
1 |
1 |
0 |
0 |
22 |
3 |
25.7 |
18,3 |
|
2 |
1 |
0 |
0 |
22 |
3 |
25.7 |
18,3 |
|
3 |
0 |
3 |
0 |
20 |
3 |
25.7 |
16,3 |
|
4 |
1 |
2 |
0 |
20 |
3 |
25.7 |
16,3 |
|
5 |
1 |
0 |
0 |
22 |
3 |
25.7 |
18,3 |
|
6 |
1 |
0 |
0 |
22 |
3 |
25.7 |
18,3 |
|
7 |
2 |
2 |
0 |
19 |
3,5 |
25.7 |
14,8 |
|
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1. |
|||||||
Table 6.2.4B.5-13: UE Power Class 3 test requirements (network signalled value "NS_14")
|
Configuration ID |
MPR (dB) |
A-MPR (dB) |
ΔTC,c (dB) |
PCMAX,c (dBm) |
T(PCMAX_L,c) (dB) |
Upper limit (dBm) |
Lower limit (dBm) |
|
1 |
0 |
3 |
0 |
20 |
3 |
25.7 |
16.3 |
|
2 |
1 |
0 |
0 |
22 |
3 |
25.7 |
18.3 |
|
3 |
1 |
1 |
0 |
21 |
3 |
25.7 |
18.3 |
|
4 |
1 |
0 |
0 |
22 |
3 |
25.7 |
18.3 |
|
5 |
2 |
1 |
0 |
20 |
3 |
25.7 |
16.3 |
|
6 |
0 |
3 |
0 |
20 |
3 |
25.7 |
16.3 |
|
7 |
1 |
0 |
0 |
22 |
3 |
25.7 |
18.3 |
|
8 |
1 |
1 |
0 |
21 |
3 |
25.7 |
17.3 |
|
9 |
1 |
0 |
0 |
22 |
3 |
25.7 |
18.3 |
|
10 |
2 |
1 |
0 |
20 |
3 |
25.7 |
16.3 |
|
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1. |
|||||||
Table 6.2.4B.5-14: UE Power Class test requirements (network signalled value "NS_15")
|
Configuration ID |
EUTRA band |
Class 1 (dBm) |
Tol. (dB) |
Class 2 (dBm) |
Tol. (dB) |
Class 3 (dBm) |
Tol. (dB) |
|
1 |
26 |
23 |
+2.7 / -3.2 |
||||
|
2 |
26 |
23 |
+2.7 / -8.2 |
||||
|
3 |
26 |
23 |
+2.7 / -4.2 |
||||
|
4 |
26 |
23 |
+2.7 / -8.2 |
||||
|
5 |
26 |
23 |
+2.7 / -14.2 |
||||
|
6 |
26 |
23 |
+2.7 / -4.2 |
||||
|
7 |
26 |
23 |
+2.7 / -3.2 |
||||
|
8 |
26 |
23 |
+2.7 / -9.2 |
||||
|
9 |
26 |
23 |
+2.7 / -14.2 |
||||
|
10 |
26 |
23 |
+2.7 / -4.2 |
||||
|
11 |
26 |
23 |
+2.7 / -6.2 |
||||
|
12 |
26 |
23 |
+2.7 / -12.2 |
||||
|
13 |
26 |
23 |
+2.7 / -7.2 |
||||
|
14 |
26 |
23 |
+2.7 / -3.2 |
||||
|
15 |
26 |
23 |
+2.7 / -4.2 |
||||
|
16 |
26 |
23 |
+2.7 / -8.2 |
||||
|
17 |
26 |
23 |
+2.7 / -3.2 |
||||
|
18 |
26 |
23 |
+2.7 / -12.2 |
||||
|
19 |
26 |
23 |
+2.7 / -4.2 |
||||
|
20 |
26 |
23 |
+2.7 / -8.2 |
||||
|
21 |
26 |
23 |
+2.7 / -3.2 |
||||
|
22 |
26 |
23 |
+2.7 / -4.2 |
||||
|
23 |
26 |
23 |
+2.7 / -9.2 |
||||
|
24 |
26 |
23 |
+2.7 / -14.2 |
||||
|
25 |
26 |
23 |
+2.7 / -3.2 |
||||
|
26 |
26 |
23 |
+2.7 / -9.2 |
Table 6.2.4B.5-15: UE Power Class test requirements (network signalled value "NS_16") when lower channel edge is at 807 MHz
|
Configuration ID |
EUTRA band |
Class 1 (dBm) |
Tol. (dB) |
Class 2 (dBm) |
Tol. (dB) |
Class 3 (dBm) |
Tol. (dB) |
|
1 |
27 |
23 |
+2.7 / -2.7 |
||||
|
2 |
27 |
23 |
+2.7 / -3.7 |
||||
|
3 |
27 |
23 |
+2.7 / -4.7 |
||||
|
4 |
27 |
23 |
+2.7 / -2.7 |
||||
|
5 |
27 |
23 |
+2.7 / -4.7 |
||||
|
6 |
27 |
23 |
+2.7 / -6.2 |
||||
|
7 |
27 |
23 |
+2.7 / -8.2 |
||||
|
8 |
27 |
23 |
+2.7 / -9.7 |
||||
|
9 |
27 |
23 |
+2.7 / -4.7 |
||||
|
10 |
27 |
23 |
+2.7 / -6.2 |
||||
|
11 |
27 |
23 |
+2.7 / -11.7 |
||||
|
12 |
27 |
23 |
+2.7 / -8.2 |
||||
|
13 |
27 |
23 |
+2.7 / -11.7 |
||||
|
14 |
27 |
23 |
+2.7 / -12.7 |
||||
|
15 |
27 |
23 |
+2.7 / -9.7 |
||||
|
16 |
27 |
23 |
+2.7 / -2.7 |
||||
|
17 |
27 |
23 |
+2.7 / -8.2 |
||||
|
18 |
27 |
23 |
+2.7 / -4.7 |
||||
|
19 |
27 |
23 |
+2.7 / -8.2 |
||||
|
20 |
27 |
23 |
+2.7 / -13.7 |
||||
|
21 |
27 |
23 |
+2.7 / -13.7 |
||||
|
22 |
27 |
23 |
+2.7 / -14.7 |
||||
|
23 |
27 |
23 |
+2.7 / -13.7 |
||||
|
24 |
27 |
23 |
+2.7 / -13.7 |
Table 6.2.4B.5-16: UE Power Class test requirements (network signalled value "NS_16") when lower channel edge is at 808.5 MHz
|
Configuration ID |
EUTRA band |
Class 1 (dBm) |
Tol. (dB) |
Class 2 (dBm) |
Tol. (dB) |
Class 3 (dBm) |
Tol. (dB) |
|
1 |
27 |
23 |
+2.7 / -2.7 |
||||
|
2 |
27 |
23 |
+2.7 / -3.7 |
||||
|
3 |
27 |
23 |
+2.7 / -5.2 |
||||
|
4 |
27 |
23 |
+2.7 / -2.7 |
||||
|
5 |
27 |
23 |
+2.7 / -3.7 |
||||
|
6 |
27 |
23 |
+2.7 / -3.7 |
||||
|
7 |
27 |
23 |
+2.7 / -4.7 |
||||
|
8 |
27 |
23 |
+2.7 / -2.7 |
||||
|
9 |
27 |
23 |
+2.7 / -3.7 |
||||
|
10 |
27 |
23 |
+2.7 / -4.7 |
||||
|
11 |
27 |
23 |
+2.7 / -6.2 |
||||
|
12 |
27 |
23 |
+2.7 / -6.2 |
||||
|
13 |
27 |
23 |
+2.7 / -8.2 |
||||
|
14 |
27 |
23 |
+2.7 / -9.7 |
||||
|
15 |
27 |
23 |
+2.7 / -9.7 |
||||
|
16 |
27 |
23 |
+2.7 / -2.7 |
||||
|
17 |
27 |
23 |
+2.7 / -6.2 |
||||
|
18 |
27 |
23 |
+2.7 / -4.7 |
||||
|
19 |
27 |
23 |
+2.7 / -4.7 |
||||
|
20 |
27 |
23 |
+2.7 / -9.7 |
||||
|
21 |
27 |
23 |
+2.7 / -11.7 |
||||
|
22 |
27 |
23 |
+2.7 / -12.7 |
||||
|
23 |
27 |
23 |
+2.7 / -11.7 |
||||
|
24 |
27 |
23 |
+2.7 / -11.7 |
Table 6.2.4B.5-17: UE Power Class test requirements (network signalled value "NS_16") when lower channel edge is at 812 MHz
|
Configuration ID |
EUTRA band |
Class 1 (dBm) |
Tol. (dB) |
Class 2 (dBm) |
Tol. (dB) |
Class 3 (dBm) |
Tol. (dB) |
|
1 |
27 |
23 |
+2.7 / – 2.7 |
||||
|
2 |
27 |
23 |
+2.7 / – 3.7 |
||||
|
3 |
27 |
23 |
+2.7 / – 4.7 |
||||
|
4 |
27 |
23 |
+2.7 / – 2.7 |
||||
|
5 |
27 |
23 |
+2.7 / -3.7 |
||||
|
6 |
27 |
23 |
+2.7 / -3.7 |
||||
|
7 |
27 |
23 |
+2.7 / -4.7 |
||||
|
8 |
27 |
23 |
+2.7 / -2.7 |
||||
|
9 |
27 |
23 |
+2.7 / -3.7 |
||||
|
10 |
27 |
23 |
+2.7 / -3.7 |
||||
|
11 |
27 |
23 |
+2.7 / -3.7 |
||||
|
12 |
27 |
23 |
+2.7 / -3.7 |
||||
|
13 |
27 |
23 |
+2.7 / -3.7 |
||||
|
14 |
27 |
23 |
+2.7 / -4.7 |
||||
|
15 |
27 |
23 |
+2.7 / -2.7 |
||||
|
16 |
27 |
23 |
+2.7 / -2.7 |
||||
|
17 |
27 |
23 |
+2.7 / -3.7 |
||||
|
18 |
27 |
23 |
+2.7 / -3.7 |
||||
|
19 |
27 |
23 |
+2.7 / -3.7 |
||||
|
20 |
27 |
23 |
+2.7 / -4.7 |
||||
|
21 |
27 |
23 |
+2.7 / -8.2 |
||||
|
22 |
27 |
23 |
+2.7 / -9.7 |
||||
|
23 |
27 |
23 |
+2.7 / -6.2 |
||||
|
24 |
27 |
23 |
+2.7 / -4.7 |
Table 6.2.4B.5-18: UE Power Class test requirements (network signalled value "NS_20 for Band 23")
TBD
Table 6.2.4B.5-19: UE Power Class 3 test requirements (network signalled value "NS_21 for Band 30")
|
Configuration ID |
MPR (dB) |
A-MPR (dB) |
ΔTC,c (dB) |
PCMAX,c (dBm) |
T(PCMAX_L,c) (dB) |
Upper limit (dBm) |
Lower limit (dBm) |
|
1 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
2 |
1 |
0 |
0 |
22 |
3.0 |
25.7 |
18.3 |
|
3 |
0 |
4 |
0 |
19 |
3.5 |
25.7 |
14.8 |
|
4 |
0 |
4 |
0 |
19 |
3.5 |
25.7 |
14.8 |
|
5 |
1 |
0 |
0 |
22 |
3.0 |
25.7 |
18.3 |
|
6 |
0 |
3 |
0 |
20 |
3.0 |
25.7 |
16.3 |
|
7 |
1 |
3 |
0 |
19 |
3.5 |
25.7 |
14.8 |
|
8 |
2 |
3 |
0 |
18 |
4.0 |
25.7 |
13.3 |
|
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1. |
|||||||
Table 6.2.4B.5-20: UE Power Class Test requirements (network signalled value "NS_22")
|
Configuration ID |
MPR (dB) |
A-MPR (dB) |
ΔTC,c (dB) |
PCMAX,c (dBm) |
T(PCMAX_L,c) (dB) |
Upper limit (dBm) |
Lower limit (dBm) |
|
1 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
2 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
3 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
4 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
5 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
6 |
1 |
4 |
0 |
18 |
5.0 |
25.7 |
12.3 |
|
7 |
1 |
3 |
0 |
19 |
5.0 |
25.7 |
13.3 |
|
8 |
0 |
3 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
9 |
0 |
3 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
10 |
1 |
3 |
0 |
19 |
5.0 |
25.7 |
13.3 |
|
11 |
1 |
3 |
0 |
19 |
5.0 |
25.7 |
13.3 |
|
12 |
1 |
5 |
0 |
17 |
5.0 |
25.7 |
11.3 |
|
13 |
1 |
4 |
0 |
18 |
5.0 |
25.7 |
12.3 |
|
14 |
0 |
3 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
15 |
0 |
3 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
16 |
1 |
3 |
0 |
19 |
5.0 |
25.7 |
13.3 |
|
17 |
1 |
3 |
0 |
19 |
5.0 |
25.7 |
13.3 |
|
18 |
1 |
5 |
0 |
17 |
5.0 |
25.7 |
11.3 |
|
19 |
1 |
4 |
0 |
18 |
5.0 |
25.7 |
12.3 |
|
20 |
0 |
3 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
21 |
0 |
3 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
22 |
1 |
3 |
0 |
19 |
5.0 |
25.7 |
13.3 |
|
23 |
1 |
3 |
0 |
19 |
5.0 |
25.7 |
13.3 |
|
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1. |
|||||||
Table 6.2.4B.5-21: UE Power Class Test requirements (network signalled value "NS_23")
|
Configuration ID |
MPR (dB) |
A-MPR (dB) |
ΔTC,c (dB) |
PCMAX,c (dBm) |
T(PCMAX_L,c) (dB) |
Upper limit (dBm) |
Lower limit (dBm) |
|
1 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
2 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
3 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
4 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
5 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
6 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
7 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
8 |
1 |
0 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1. |
|||||||
Table 6.2.4B.5-22: UE Power Class test requirements (network signalled value "NS_24")
|
Configuration ID |
MPR (dB) |
A-MPR (dB) |
ΔTC,c (dB) |
PCMAX,c (dBm) |
T(PCMAX_L,c) (dB) |
Upper limit (dBm) |
Lower limit (dBm) |
|
1 |
0 |
10 |
0 |
13 |
6.0 |
25.7 |
6.3 |
|
2 |
0 |
10 |
0 |
13 |
7.0 |
25.7 |
5.3 |
|
3 |
1 |
10 |
0 |
12 |
5.0 |
25.7 |
6.3 |
|
4 |
2 |
10 |
0 |
11 |
5.0 |
25.7 |
5.3 |
|
5 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
6 |
0 |
2 |
0 |
21 |
5.0 |
25.7 |
15.3 |
|
7 |
2 |
2 |
0 |
19 |
5.0 |
25.7 |
13.3 |
|
8 |
1 |
2 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
9 |
1 |
1 |
0 |
21 |
5.0 |
25.7 |
15.3 |
|
10 |
0 |
3 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
11 |
0 |
1 |
0 |
22 |
5.0 |
25.7 |
16.3 |
|
12 |
1 |
1 |
0 |
21 |
5.0 |
25.7 |
15.3 |
|
13 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
14 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
15 |
0 |
9 |
0 |
14 |
6.0 |
25.7 |
7.3 |
|
16 |
0 |
9 |
0 |
14 |
6.0 |
25.7 |
7.3 |
|
17 |
1 |
9 |
0 |
13 |
6.0 |
25.7 |
6.3 |
|
18 |
0 |
17 |
0 |
6 |
7.0 |
25.7 |
-1.7 |
|
19 |
1 |
17 |
0 |
5 |
7.0 |
25.7 |
-2.7 |
|
20 |
2 |
17 |
0 |
4 |
7.0 |
25.7 |
-3.7 |
|
21 |
0 |
2 |
0 |
21 |
3.0 |
25.7 |
17.3 |
|
22 |
0 |
2 |
0 |
21 |
3.0 |
25.7 |
17.3 |
|
23 |
1 |
2 |
0 |
20 |
5.0 |
25.7 |
14.3 |
|
24 |
2 |
8 |
0 |
13 |
6.0 |
25.7 |
6.3 |
|
25 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
26 |
0 |
7 |
0 |
16 |
5.0 |
25.7 |
10.3 |
|
27 |
1 |
7 |
0 |
15 |
6.0 |
25.7 |
8.3 |
|
28 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
29 |
0 |
17 |
0 |
6 |
7.0 |
25.7 |
-1.7 |
|
30 |
0 |
17 |
0 |
6 |
7.0 |
25.7 |
-1.7 |
|
31 |
1 |
17 |
0 |
5 |
7.0 |
25.7 |
-2.7 |
|
32 |
2 |
17 |
0 |
4 |
7.0 |
25.7 |
-3.7 |
|
33 |
0 |
17 |
0 |
6 |
7.0 |
25.7 |
-1.7 |
|
34 |
0 |
17 |
0 |
6 |
7.0 |
25.7. |
-1.7 |
|
35 |
1 |
17 |
0 |
5 |
7.0 |
25.7 |
-2.7 |
|
36 |
2 |
17 |
0 |
4 |
7.0 |
25.7 |
-3.7 |
|
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1. |
|||||||
Table 6.2.4B.5-23: UE Power Class test requirements (network signalled value "NS_25")
|
Configuration ID |
MPR (dB) |
A-MPR (dB) |
ΔTC,c (dB) |
PCMAX,c (dBm) |
T(PCMAX_L,c) (dB) |
Upper limit (dBm) |
Lower limit (dBm) |
|
1 |
1 |
5 |
0 |
17 |
5.0 |
25.7 |
11.3 |
|
2 |
2 |
5 |
0 |
16 |
5.0 |
25.7 |
10.3 |
|
3 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
4 |
0 |
2 |
0 |
21 |
3.0 |
25.7 |
17.3 |
|
5 |
0 |
2 |
0 |
21 |
5.0 |
25.7 |
15.3 |
|
6 |
1 |
2 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
7 |
0 |
2 |
0 |
21 |
5.0 |
25.7 |
15.3 |
|
8 |
2 |
2 |
0 |
19 |
5.0 |
25.7 |
13.3 |
|
9 |
1 |
2 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
10 |
1 |
1 |
0 |
21 |
3.0 |
25.7 |
17.3 |
|
11 |
0 |
3 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
12 |
0 |
1 |
0 |
22 |
3.0 |
25.7 |
18.3 |
|
13 |
0 |
1 |
0 |
22 |
3.0 |
25.7 |
18.3 |
|
14 |
1 |
1 |
0 |
21 |
3.0 |
25.7 |
17.3 |
|
15 |
1 |
5 |
0 |
17 |
5.0 |
25.7 |
11.3 |
|
16 |
2 |
1 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
17 |
1 |
5 |
0 |
17 |
5.0 |
25.7 |
11.3 |
|
18 |
1 |
1 |
0 |
21 |
5.0 |
25.7 |
15.3 |
|
19 |
2 |
1 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
20 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
21 |
0 |
10 |
0 |
13 |
6.0 |
25.7 |
6.3 |
|
22 |
0 |
10 |
0 |
13 |
6.0 |
25.7 |
6.3 |
|
23 |
1 |
10 |
0 |
12 |
6.0 |
25.7 |
5.3 |
|
24 |
2 |
10 |
0 |
11 |
6.0 |
25.7 |
4.3 |
|
25 |
1 |
7 |
0 |
15 |
6.0 |
25.7 |
8.3 |
|
26 |
2 |
7 |
0 |
14 |
6.0 |
25.7 |
7.3 |
|
27 |
1 |
11 |
0 |
11 |
6.0 |
25.7 |
4.3 |
|
28 |
2 |
11 |
0 |
10 |
7.0 |
25.7 |
2.3 |
|
29 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
30 |
0 |
4 |
0 |
19 |
5.0 |
25.7 |
13.3 |
|
31 |
1 |
4 |
0 |
18 |
5.0 |
25.7 |
12.3 |
|
32 |
1 |
3 |
0 |
19 |
5.0 |
25.7 |
13.3 |
|
33 |
2 |
1 |
0 |
20 |
6.0 |
25.7 |
13.3 |
|
34 |
0 |
1 |
0 |
22 |
3.0 |
25.7 |
18.3 |
|
35 |
0 |
1 |
0 |
22 |
3.0 |
25.7 |
18.3 |
|
36 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
37 |
0 |
13 |
0 |
10 |
7.0 |
25.7 |
2.3 |
|
38 |
0 |
13 |
0 |
10 |
7.0 |
25.7 |
2.3 |
|
39 |
1 |
13 |
0 |
9 |
7.0 |
25.7 |
1.3 |
|
40 |
2 |
13 |
0 |
8 |
7.0 |
25.7 |
0.3 |
|
41 |
0 |
11 |
0 |
12 |
6.0 |
25.7 |
5.3 |
|
42 |
0 |
11 |
0 |
12 |
6.0 |
25.7 |
5.3 |
|
43 |
2 |
11 |
0 |
10 |
7.0 |
25.7 |
2.3 |
|
44 |
1 |
11 |
0 |
11 |
6.0 |
25.7 |
4.3 |
|
45 |
0 |
13 |
0 |
10 |
7.0 |
25.7 |
2.3 |
|
46 |
2 |
13 |
0 |
8 |
7.0 |
25.7 |
0.3 |
|
47 |
0 |
0 |
0 |
23 |
3.0 |
25.7 |
19.3 |
|
48 |
0 |
13 |
0 |
10 |
7.0 |
25.7 |
2.3 |
|
49 |
0 |
13 |
0 |
10 |
7.0 |
25.7 |
2.3 |
|
50 |
1 |
13 |
0 |
9 |
7.0 |
25.7 |
1.3 |
|
51 |
2 |
13 |
0 |
8 |
7.0 |
25.7 |
0.3 |
|
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1. |
|||||||
Table 6.2.4B.5-24: Reserved
Table 6.2.4B.5-25: UE Power Class test requirements (network signalled value "NS_27")
|
Configuration ID |
MPR (dB) |
A-MPR (dB) |
ΔTC,c (dB) |
PCMAX,c (dBm) |
T(PCMAX_L,c) (dB) |
Upper limit (dBm) |
Lower limit (dBm) |
|
1 |
0 |
0 |
0 |
23 |
3.0 |
26 |
19 |
|
2 |
0 |
0 |
0 |
23 |
3.0 |
26 |
19 |
|
3 |
1 |
0 |
0 |
22 |
5.0 |
26 |
16 |
|
4 |
2 |
0 |
0 |
21 |
5.0 |
26 |
15 |
|
5 |
0 |
0 |
0 |
23 |
3.0 |
26 |
19 |
|
6 |
0 |
0 |
0 |
23 |
3.0 |
26 |
19 |
|
7 |
1 |
0 |
0 |
22 |
5.0 |
26 |
16 |
|
8 |
2 |
0 |
0 |
21 |
5.0 |
26 |
15 |
|
9 |
0 |
4 |
0 |
19 |
5.0 |
26 |
13 |
|
10 |
0 |
0 |
0 |
23 |
3.0 |
26 |
19 |
|
11 |
0 |
0 |
0 |
23 |
3.0 |
26 |
19 |
|
12 |
0 |
4 |
0 |
19 |
5.0 |
26 |
13 |
|
13 |
0 |
0 |
0 |
23 |
3.0 |
26 |
19 |
|
14 |
0 |
0 |
0 |
23 |
3.0 |
26 |
19 |
|
15 |
1 |
2 |
0 |
20 |
6.0 |
26 |
13 |
|
16 |
2 |
2 |
0 |
19 |
5.0 |
26 |
13 |
|
17 |
0 |
4 |
0 |
19 |
5.0 |
26 |
13 |
|
18 |
0 |
1 |
0 |
22 |
5.0 |
26 |
16 |
|
19 |
0 |
0 |
0 |
23 |
3.0 |
26 |
19 |
|
20 |
1 |
0 |
0 |
22 |
5.0 |
26 |
16 |
|
21 |
0 |
4 |
0 |
19 |
5.0 |
26 |
13 |
|
22 |
0 |
1 |
0 |
22 |
5.0 |
26 |
16 |
|
23 |
0 |
0 |
0 |
23 |
3.0 |
26 |
19 |
|
24 |
1 |
0 |
0 |
22 |
5.0 |
26 |
16 |
|
25 |
1 |
3 |
0 |
19 |
5.0 |
26 |
13 |
|
26 |
2 |
3 |
0 |
18 |
5.0 |
26 |
12 |
|
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1. |
|||||||
Table 6.2.4B.5-26: UE Power Class test requirements (network signalled value "NS_35")
|
Configuration ID |
MPR (dB) |
A-MPR (dB) |
ΔTC,c (dB) |
PCMAX,c (dBm) |
T(PCMAX_L,c) (dB) |
Upper limit (dBm) |
Lower limit (dBm) |
|
1 |
0 |
0 |
0 |
23 |
2 |
25.7 |
18.8 |
|
2 |
0 |
0 |
0 |
23 |
2 |
25.7 |
18.8 |
|
3 |
0 |
0 |
0 |
23 |
2 |
25.7 |
18.8 |
|
4 |
0 |
0 |
0 |
23 |
2 |
25.7 |
18.8 |
|
5 |
0 |
0 |
0 |
23 |
2 |
25.7 |
18.8 |
|
6 |
0 |
0 |
0 |
23 |
2 |
25.7 |
18.8 |
|
7 |
0 |
0 |
0 |
23 |
2 |
25.7 |
18.8 |
|
8 |
0 |
0 |
0 |
23 |
2 |
25.7 |
18.8 |
|
9 |
0 |
0 |
0 |
23 |
2 |
25.7 |
18.8 |
|
10 |
0 |
0 |
0 |
23 |
2 |
25.7 |
18.8 |
|
11 |
0 |
0 |
0 |
23 |
2 |
25.7 |
18.8 |
|
12 |
0 |
0 |
0 |
23 |
2 |
25.7 |
18.8 |
|
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1. |
|||||||
Table 6.2.4B.5-27: UE Power Class 3 test requirements (network signalled value "NS_36")
|
Configuration ID |
MPR (dB) |
A-MPR (dB) |
ΔTC,c (dB) |
PCMAX,c (dBm) |
T(PCMAX_L,c) (dB) |
Upper limit (dBm) |
Lower limit (dBm) |
|
1 |
0 |
2 |
0 |
21 |
5 |
25.7 |
15.3 |
|
2 |
1 |
4 |
0 |
18 |
5 |
25.7 |
12.3 |
|
3 |
1 |
1 |
0 |
21 |
5 |
25.7 |
15.3 |
|
4 |
1 |
3 |
0 |
19 |
5 |
25.7 |
13.3 |
|
5 |
1 |
0 |
0 |
22 |
5 |
25.7 |
16.3 |
|
6 |
2 |
0 |
0 |
21 |
5 |
25.7 |
15.3 |
|
7 |
1 |
0 |
0 |
22 |
5 |
25.7 |
16.3 |
|
8 |
2 |
0 |
0 |
21 |
5 |
25.7 |
15.3 |
|
9 |
1 |
10 |
0 |
12 |
6 |
25.7 |
5.3 |
|
10 |
0 |
10 |
0 |
13 |
6 |
25.7 |
6.3 |
|
11 |
1 |
8 |
0 |
14 |
6 |
25.7 |
7.3 |
|
12 |
1 |
6 |
0 |
16 |
5 |
25.7 |
10.3 |
|
13 |
0 |
6 |
0 |
17 |
5 |
25.7 |
11.3 |
|
14 |
0 |
0 |
0 |
23 |
3 |
25.7 |
19.3 |
|
15 |
1 |
0 |
0 |
22 |
5 |
25.7 |
16.3 |
|
16 |
2 |
0 |
0 |
21 |
5 |
25.7 |
15.3 |
|
17 |
1 |
10 |
0 |
12 |
6 |
25.7 |
5.3 |
|
18 |
1 |
9 |
0 |
13 |
6 |
25.7 |
6.3 |
|
19 |
1 |
7 |
0 |
15 |
6 |
25.7 |
8.3 |
|
20 |
0 |
6 |
0 |
17 |
5 |
25.7 |
11.3 |
|
21 |
0 |
0 |
0 |
23 |
3 |
25.7 |
19.3 |
|
22 |
1 |
0 |
0 |
22 |
5 |
25.7 |
16.3 |
|
23 |
2 |
0 |
0 |
21 |
5 |
25.7 |
15.3 |
|
24 |
1 |
0 |
0 |
22 |
5 |
25.7 |
16.3 |
|
25 |
2 |
0 |
0 |
21 |
5 |
25.7 |
15.3 |
|
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1. |
|||||||
Table 6.2.4B.5-28: UE Power Class 3 test requirements (network signalled value "NS_56")
|
Configuration ID |
MPR (dB) |
A-MPR (dB) |
ΔTC,c (dB) |
PCMAX,c (dBm) |
T(PCMAX_L,c) (dB) |
Upper limit (dBm) |
Lower limit (dBm) |
|
1 |
0 |
8 |
0 |
15 |
6 |
25.7 |
8.3 |
|
2 |
1 |
2 |
0 |
20 |
6 |
25.7 |
13.3 |
|
3 |
2 |
2 |
0 |
19 |
5 |
25.7 |
13.3 |
|
4 |
0 |
7 |
0 |
16 |
5 |
25.7 |
10.3 |
|
5 |
0 |
5 |
0 |
18 |
5 |
25.7 |
12.3 |
|
6 |
1 |
7 |
0 |
15 |
6 |
25.7 |
8.3 |
|
7 |
2 |
7 |
0 |
14 |
6 |
25.7 |
7.3 |
|
8 |
0 |
5 |
0 |
18 |
5 |
25.7 |
12.3 |
|
9 |
0 |
4 |
0 |
19 |
5 |
25.7 |
13.3 |
|
10 |
0 |
5 |
0 |
18 |
5 |
25.7 |
12.3 |
|
11 |
0 |
5 |
0 |
18 |
5 |
25.7 |
12.3 |
|
12 |
1 |
2 |
0 |
20 |
6 |
25.7 |
13.3 |
|
13 |
0 |
3 |
0 |
20 |
6 |
25.7 |
13.3 |
|
14 |
1 |
3 |
0 |
19 |
5 |
25.7 |
13.3 |
|
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1. |
|||||||