8.5.1 FDD
36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification
8.5.1.1 FDD PHICH Single-antenna Port Performance
8.5.1.1.1 Test purpose
This test verifies the demodulation performance of PHICH for a single antenna port with a given SNR for which the average probability of miss detection of Hybrid Indicator ("ACK to NACK") of the specified reference measurement channels remains below a specified value.
8.5.1.1.2 Test applicability
This test applies to all types of E-UTRA FDD UE release 8 and forward.
8.5.1.1.3 Minimum conformance requirements
The receiver characteristics of the PHICH are determined by the probability of miss-detecting an ACK for a NACK (Pm-an). It is assumed that there is no bias applied to the detection of ACK and NACK (zero-threshold detection).
Table 8.5.1.1.3-1: Test Parameters for PHICH
|
Parameter |
Unit |
Single antenna port |
|
|
Downlink power allocation |
PDCCH_RA PHICH_RA OCNG_RA |
dB |
0 |
|
PCFICH_RB PDCCH_RB PHICH_RB OCNG_RB |
dB |
0 |
|
|
PHICH duration |
Normal |
||
|
Number of PHICH groups (Note 1) |
Ng = 1 |
||
|
PDCCH Content |
UL Grant should be included with the proper information aligned with A.3.6. |
||
|
Unused RE-s and PRB-s |
OCNG |
||
|
Cell ID |
0 |
||
|
|
dBm/15kHz |
-98 |
|
|
Cyclic prefix |
Normal |
||
|
Note 1: according to Clause 6.9 in TS 36.211 [8] Note 2: PHICH power settings refer to PHICH group power, i.e. the total power of all active PHICH sequences within a PHICH group. |
|||
at antenna portFor the parameters specified in Table 8.5.1.1.3-1 the average probability of a miss-detecting an ACK for a NACK (Pm-an) shall be below the specified value in Table 8.5.1.1.3-2.
Table 8.5.1.1.3-2: Minimum performance PHICH
|
Test number |
Bandwidth |
Reference Channel |
OCNG Pattern |
Propagation Condition |
Antenna configuration and correlation Matrix |
Reference value |
|
|
Pm-an (%) |
SNR (dB) |
||||||
|
1 |
10 MHz |
R.18 |
OP.1 FDD |
ETU70 |
1 x 2 Low |
0.1 |
5.5 |
|
2 |
10 MHz |
R.24 |
OP.1 FDD |
ETU70 |
1 x 2 Low |
0.1 |
0.6 |
The normative reference for this requirement is TS 36.101 [2] clause 8.5.
8.5.1.1.4 Test description
8.5.1.1.4.1 Initial conditions
Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.
Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.
Test Environment: Normal as defined in TS 36.508 [7] clause 4.1.
Frequencies to be tested: Mid Range as defined in TS 36.508 [7] clause 4.3.1.1.
Channel Bandwidths to be tested: 10 MHz, as defined in TS 36.508 [7] clause 4.3.1.1
1. Connect the SS, the faders and AWGN noise sources to the UE antenna connector (s) as shown in TS 36.508 [7] Annex A, Figure A.9.
2. The parameter settings for the cell are set up according to Table 8.5.1.1.3-1.
3. Downlink signals are initially set up according to Annex C0, C.1 and Annex C.3.2 and uplink signals according to Annex H.1 and H.3.2.
4. Propagation conditions are set according to Annex B.0.
5. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 8.5.1.1.4.3.
8.5.1.1.4.2 Test procedure
1. Set the parameters of bandwidth, reference Channel, the propagation condition, antenna configuration, the correlation matrix and the SNR according to Table 8.5.1.1.5-1 Test 1 as appropriate.
2. SS shall schedule PUSCH transmissions according to Annex A.2.2.1.1 Table A.2.2.1.1-1 to happen during 8 consecutive uplink TTIs via PDCCH DCI format 0 with new data indicator set to true. Since the UE has no payload, the UE shall send uplink MAC padding bits in PUSCH. SS upon receiving the PUSCH transmissions will transmit the associated ACKs. PHICH is set according to Annex 3.6 Table A.3.6-1. SS will only transmit PDCCH to schedule PUSCH transmission in the appropriate sub-frames. Table 8.5.1.1.4.2-1 indicates the transmissions for one cycle.
Table 8.5.1.1.4.2-1: PHICH test pattern
|
TTI |
1-4 |
5-8 |
9-12 |
13-16 |
17-20 |
21-24 |
|
PDCCH |
S |
S |
– |
– |
S |
S |
|
PHICH |
– |
– |
A |
A |
– |
– |
|
PUSCH |
T |
T |
R |
R |
T |
|
|
UL HARQ Process |
1-4 |
5-8 |
1-4 |
5-8 |
1-4 |
5-8 |
|
Note 1: This table gives an example test pattern for HARQ process for FDD PHICH test Note 2: Following notation is used: S: represents sending PDCCH DCI format 0 to schedule a future PUSCH transmission A: represents the ACK transmission on PHICH T: represents a scheduled PUSCH transmission R: represents a potential PUSCH re-transmission due to a missed ACK |
||||||
3. SS will only monitor for uplink retransmissions due to ACK missed-detections. Such re-transmissions (if they occur) will potentially happen in TTI 13 to 20. DTXs on TTI 13 to 20 are counted as successful ACK receptions while any transmission on these TTIs is counted as NACKs.
4. Repeat steps 1 – 3 for a duration sufficient to achieve statistical significance according to Annex G clause G.4 and measure Pm-an. Pm-an is (NACK) / (ACK + NACK).
If Pm-an is less than the value specified in table 8.5.1.1.5-1, pass the UE. Otherwise fail the UE.
5. Repeat the same procedure (steps 1 to 3 ) with test conditions according to the Table 8.5.1.1.5-1 for Test 2.
8.5.1.1.4.3 Message contents
Message contents are according to TS 36.508 [7] clause 4.6, with the following exceptions
Table 8.5.1.1.4.3-1: MAC-MainConfig-RBC
|
Derivation Path: TS 36.508 [7] clause 4.8.2.1.5, Table 4.8.2.1.5-1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
MAC-MainConfig-RBC ::= SEQUENCE { |
||||
|
dl-SCH-Config SEQUENCE {} |
Not present |
|||
|
ul-SCH-Config SEQUENCE { |
||||
|
maxHARQ-Tx |
n2 |
Only one retransmission per UL HARQ |
||
8.5.1.1.5 Test requirement
For the parameters specified in Table 8.5.1.1.3-1 the average probability of a miss-detecting ACK for NACK (Pm-dsg) shall be below the specified value in Table 8.5.1.1.5-1.
Table 8.5.1.1.5-1: Test requirement PHICH
|
Test number |
Bandwidth |
Reference Channel |
OCNG Pattern |
Propagation Condition |
Antenna configuration and correlation Matrix |
Reference value |
|
|
Pm-an (%) |
SNR (dB) |
||||||
|
1 |
10 MHz |
R.18 |
OP.1 FDD |
ETU70 |
1 x 2 Low |
0.1 |
6.4 |
|
2 |
10 MHz |
R.24 |
OP.1 FDD |
ETU70 |
1 x 2 Low |
0.1 |
1.5 |
8.5.1.2 FDD PHICH Transmit Diversity Performance
8.5.1.2.1 FDD PHICH Transmit Diversity 2×2
8.5.1.2.1.1 Test purpose
This test verifies the demodulation performance of PHICH for transmit diversity with a given SNR for which the average probability of miss detection of Hybrid Indicator ("ACK to NACK") of the specified reference measurement channels remains below a specified value.
8.5.1.2.1.2 Test applicability
This test applies to all types of E-UTRA FDD UE release 8.
8.5.1.2.1.3 Minimum conformance requirements
The receiver characteristics of the PHICH are determined by the probability of miss-detecting an ACK for a NACK (Pm-an). It is assumed that there is no bias applied to the detection of ACK and NACK (zero-threshold detection).
Table 8.5.1.2.1.3-1: Test Parameters for PHICH
|
Parameter |
Unit |
Transmit diversity |
|
|
Downlink power allocation |
PDCCH_RA PHICH_RA OCNG_RA |
dB |
-3 |
|
PCFICH_RB PDCCH_RB PHICH_RB OCNG_RB |
dB |
-3 |
|
|
PHICH duration |
Normal |
||
|
Number of PHICH groups (Note 1) |
Ng = 1 |
||
|
PDCCH Content |
UL Grant should be included with the proper information aligned with A.3.6. |
||
|
Unused RE-s and PRB-s |
OCNG |
||
|
Cell ID |
0 |
||
|
|
dBm/15kHz |
-98 |
|
|
Cyclic prefix |
Normal |
||
|
Note 1: according to Clause 6.9 in TS 36.211 [8] Note 2: PHICH power settings refer to PHICH group power, i.e. the total power of all active PHICH sequences within a PHICH group. |
|||
at antenna portFor the parameters specified in Table 8.5.1.2.1.3-1 the average probability of a miss-detecting an ACK for a NACK (Pm-an) shall be below the specified value in Table 8.5.1.2.1.3-2
Table 8.5.1.2.1.3-2: Minimum performance PHICH 2 Tx Antenna Port
|
Test number |
Bandwidth |
Reference Channel |
OCNG Pattern |
Propagation Condition |
Antenna configuration and correlation Matrix |
Reference value |
|
|
Pm-an (%) |
SNR (dB) |
||||||
|
1 |
1.4 MHz |
R.19A |
OP.1 FDD |
EPA5 |
2 x 2 Low |
0.1 |
5.6 |
|
1A |
5MHz (Note 1) |
R.19-1 |
OP.1 FDD |
EVA 70 |
2×2 Low |
0.1 |
4 |
|
Note 1: Test case applicability is defined in 8.1.2.1. |
|||||||
The normative reference for this requirement is TS 36.101 [2] clause 8.5.1.
8.5.1.2.1.4 Test description
8.5.1.2.1.4.1 Initial conditions
Test Environment: Normal as defined in TS 36.508 [7] clause 4.1.
Frequencies to be tested: Mid Range as defined in TS 36.508 [7] clause 4.3.1.1.
Channel Bandwidths to be tested: Depending on the bandwidth specified per test number in Table 8.5.1.2.1.3-2, as defined in TS 36.508 [7] clause 4.3.1.1
1. Connect the SS, the faders and AWGN noise sources to the UE antenna connector (s) as shown in TS 36.508 [7] Annex A, Figure A.10.
2. The parameter settings for the cell are set up according to Table 8.5.1.2.1.3-1.
3. Downlink signals are initially set up according to Annex C.1 and C.3.2 and uplink signals according to Annex H.1 and H.3.2.
4. Propagation conditions are set according to Annex B clauses B.0.
5. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 8.5.1.2.1.4.3.
8.5.1.2.1.4.2 Test procedure
1. Set the parameters of bandwidth, reference Channel, the propagation condition, antenna configuration, the correlation matrix and the SNR according to Table 8.5.1.2.1.5-1.
2. SS shall schedule PUSCH transmissions according to Annex A.2.2.1.1 Table A.2.2.1.1-1 to happen during 8 consecutive uplink TTIs via PDCCH DCI format 0 with new data indicator set to true. Since the UE has no payload, the UE shall send uplink MAC padding bits in PUSCH. SS upon receiving the PUSCH transmissions will transmit the associated ACKs. PHICH is set according to Annex 3.6 Table A.3.6-1. SS will only transmit PDCCH to schedule PUSCH transmission in the appropriate sub-frames. Table 8.5.1.2.1.4.2-1 indicates the transmissions for one cycle.
Table 8.5.1.2.1.4.2-1: PHICH test pattern
|
TTI |
1-4 |
5-8 |
9-12 |
13-16 |
17-20 |
21-24 |
|
PDCCH |
S |
S |
– |
– |
S |
S |
|
PHICH |
– |
– |
A |
A |
– |
– |
|
PUSCH |
T |
T |
R |
R |
T |
|
|
UL HARQ Process |
1-4 |
5-8 |
1-4 |
5-8 |
1-4 |
5-8 |
|
Note 1: This table gives an example test pattern for HARQ process for FDD PHICH test Note 2: Following notation is used: S: represents sending PDCCH DCI format 0 to schedule a future PUSCH transmission A: represents the ACK transmission on PHICH T: represents a scheduled PUSCH transmission R: represents a potential PUSCH re-transmission due to a missed ACK |
||||||
3. SS will only monitor for uplink retransmissions due to ACK missed-detections. Such re-transmissions (if they occur) will potentially happen in TTI 13 to 20. DTXs on TTI 13 to 20 are counted as successful ACK receptions while any transmission on these TTIs is counted as NACKs.
4. Repeat steps 1 – 3 for a duration sufficient to achieve statistical significance according to Annex G clause G.4 and measure Pm-an. Pm-an is (NACK) / (ACK + NACK).
If Pm-an is less than the value specified in table 8.5.1.2.1.5-1, pass the UE. Otherwise fail the UE.
8.5.1.2.1.4.3 Message contents
Message contents are according to TS 36.508 [7] clause 4.6 with the following exceptions
Table 8.5.1.2.1.4.3-1: MAC-MainConfig-RBC
|
Derivation Path: TS 36.508 [7] clause 4.8.2.1.5, Table 4.8.2.1.5-1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
MAC-MainConfig-RBC ::= SEQUENCE { |
||||
|
dl-SCH-Config SEQUENCE {} |
Not present |
|||
|
ul-SCH-Config SEQUENCE { |
||||
|
maxHARQ-Tx |
n2 |
Only one retransmission per UL HARQ |
||
8.5.1.2.1.5 Test requirement
For the parameters specified in Table 8.5.1.2.1.3-1 the average probability of a miss-detecting ACK for NACK (Pm-dsg) shall be below the specified value in Table 8.5.1.2.1.5-1.
Table 8.5.1.2.1.5-1: Test requirement PHICH 2 Tx Antenna Port
|
Test number |
Bandwidth |
Reference Channel |
OCNG Pattern |
Propagation Condition |
Antenna configuration and correlation Matrix |
Reference value |
|
|
Pm-an (%) |
SNR (dB) |
||||||
|
1 |
1.4 MHz |
R.19A |
OP.1 FDD |
EPA5 |
2 x 2 Low |
0.1 |
6.7 |
|
1A |
5MHz (Note 1) |
R.19-1 |
OP.1 FDD |
EVA 70 |
2×2 Low |
0.1 |
5.1 |
|
Note 1: Test case is applicable (according to sub clause 8.1.2.1) to UE’s which, from the E-UTRA operating bands defined in Table 5.2-1, support only E-UTRA band 31. |
|||||||
8.5.1.2.1_1 FDD PHICH Transmit Diversity 2×2 (Release 9 and forward)
8.5.1.2.1_1.1 Test purpose
This test verifies the demodulation performance of PHICH for transmit diversity with a given SNR for which the average probability of miss detection of Hybrid Indicator ("ACK to NACK") of the specified reference measurement channels remains below a specified value.
8.5.1.2.1_1.2 Test applicability
This test applies to all types of E-UTRA FDD UE release 9 and forward.
8.5.1.2.1_1.3 Minimum conformance requirements
The receiver characteristics of the PHICH are determined by the probability of miss-detecting an ACK for a NACK (Pm-an). It is assumed that there is no bias applied to the detection of ACK and NACK (zero-threshold detection).
Table 8.5.1.2.1_1.3-1: Test Parameters for PHICH
|
Parameter |
Unit |
Transmit diversity |
|
|
Downlink power allocation |
PDCCH_RA PHICH_RA OCNG_RA |
dB |
-3 |
|
PCFICH_RB PDCCH_RB PHICH_RB OCNG_RB |
dB |
-3 |
|
|
PHICH duration |
Normal |
||
|
Number of PHICH groups (Note 1) |
Ng = 1 |
||
|
PDCCH Content |
UL Grant should be included with the proper information aligned with A.3.6. |
||
|
Unused RE-s and PRB-s |
OCNG |
||
|
Cell ID |
0 |
||
|
|
dBm/15kHz |
-98 |
|
|
Cyclic prefix |
Normal |
||
|
Note 1: according to Clause 6.9 in TS 36.211 [8] Note 2: PHICH power settings refer to PHICH group power, i.e. the total power of all active PHICH sequences within a PHICH group. |
|||
at antenna portFor the parameters specified in Table 8.5.1.2.1_1.3-1 the average probability of a miss-detecting an ACK for a NACK (Pm-an) shall be below the specified value in Table 8.5.1.2.1_1.3-2
Table 8.5.1.2.1_1.3-2: Minimum performance PHICH 2 Tx Antenna Port
|
Test number |
Bandwidth |
Reference Channel |
OCNG Pattern |
Propagation Condition |
Antenna configuration and correlation Matrix |
Reference value |
|
|
Pm-an (%) |
SNR (dB) |
||||||
|
1 |
10 MHz |
R.19 |
OP.1 FDD |
EVA70 |
2 x 2 Low |
0.1 |
4.4 |
|
1A |
5MHz (Note 1) |
R.19-1 |
OP.1 FDD |
EVA 70 |
2×2 Low |
0.1 |
4 |
|
Note 1: Test case applicability is defined in 8.1.2.1. |
|||||||
The normative reference for this requirement is TS 36.101 [2] clause 8.5.1.
8.5.1.2.1_1.4 Test description
8.5.1.2.1_1.4.1 Initial conditions
Test Environment: Normal as defined in TS 36.508 [7] clause 4.1.
Frequencies to be tested: Mid Range as defined in TS 36.508 [7] clause 4.3.1.1.
Channel Bandwidths to be tested: As specified per test number in Table 8.5.1.2.1_1.3-2 as defined in TS 36.508 [7] clause 4.3.1.1
1. Connect the SS, the faders and AWGN noise sources to the UE antenna connector (s) as shown in TS 36.508 [7] Annex A, Figure A.10.
2. The parameter settings for the cell are set up according to Table 8.5.1.2.1_1.3-1.
3. Downlink signals are initially set up according to Annex C.1 and C.3.2 and uplink signals according to Annex H.1 and H.3.2.
4. Propagation conditions are set according to Annex B clauses B.0.
5. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 8.5.1.2.1_1.4.3.
8.5.1.2.1_1.4.2 Test procedure
1. Set the parameters of bandwidth, reference Channel, the propagation condition, antenna configuration, the correlation matrix and the SNR according to Table 8.5.1.2.1_1.5-1.
2. SS shall schedule PUSCH transmissions according to Annex A.2.2.1.1 Table A.2.2.1.1-1 to happen during 8 consecutive uplink TTIs via PDCCH DCI format 0 with new data indicator set to true. Since the UE has no payload, the UE shall send uplink MAC padding bits in PUSCH. SS upon receiving the PUSCH transmissions will transmit the associated ACKs. PHICH is set according to Annex 3.6 Table A.3.6-1. SS will only transmit PDCCH to schedule PUSCH transmission in the appropriate sub-frames. Table 8.5.1.2.1_1.4.2-1 indicates the transmissions for one cycle.
Table 8.5.1.2.1_1.4.2-1: PHICH test pattern
|
TTI |
1-4 |
5-8 |
9-12 |
13-16 |
17-20 |
21-24 |
|
PDCCH |
S |
S |
– |
– |
S |
S |
|
PHICH |
– |
– |
A |
A |
– |
– |
|
PUSCH |
T |
T |
R |
R |
T |
|
|
UL HARQ Process |
1-4 |
5-8 |
1-4 |
5-8 |
1-4 |
5-8 |
|
Note 1: This table gives an example test pattern for HARQ process for FDD PHICH test Note 2: Following notation is used: S: represents sending PDCCH DCI format 0 to schedule a future PUSCH transmission A: represents the ACK transmission on PHICH T: represents a scheduled PUSCH transmission R: represents a potential PUSCH re-transmission due to a missed ACK |
||||||
3. SS will only monitor for uplink retransmissions due to ACK missed-detections. Such re-transmissions (if they occur) will potentially happen in TTI 13 to 20. DTXs on TTI 13 to 20 are counted as successful ACK receptions while any transmission on these TTIs is counted as NACKs.
4. Repeat steps 1 – 3 for a duration sufficient to achieve statistical significance according to Annex G clause G.4 and measure Pm-an. Pm-an is (NACK) / (ACK + NACK).
If Pm-an is less than the value specified in table 8.5.1.2.1_1.5-1, pass the UE. Otherwise fail the UE.
8.5.1.2.1_1.4.3 Message contents
Message contents are according to TS 36.508 [7] clause 4.6 with the following exceptions
Table 8.5.1.2.1_1.4.3-1: MAC-MainConfig-RBC
|
Derivation Path: TS 36.508 [7] clause 4.8.2.1.5, Table 4.8.2.1.5-1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
MAC-MainConfig-RBC ::= SEQUENCE { |
||||
|
dl-SCH-Config SEQUENCE {} |
Not present |
|||
|
ul-SCH-Config SEQUENCE { |
||||
|
maxHARQ-Tx |
n2 |
Only one retransmission per UL HARQ |
||
8.5.1.2.1_1.5 Test requirement
For the parameters specified in Table 8.5.1.2.1_1.3-1 the average probability of a miss-detecting ACK for NACK (Pm-dsg) shall be below the specified value in Table 8.5.1.2.1_1.5-1.
Table 8.5.1.2.1_1.5-1: Test requirement PHICH 2 Tx Antenna Port
|
Test number |
Bandwidth |
Reference Channel |
OCNG Pattern |
Propagation Condition |
Antenna configuration and correlation Matrix |
Reference value |
|
|
Pm-an (%) |
SNR (dB) |
||||||
|
1 |
10 MHz |
R.19 |
OP.1 FDD |
EVA70 |
2 x 2 Low |
0.1 |
+5.5 |
|
1A |
5MHz (Note 1) |
R.19-1 |
OP.1 FDD |
EVA 70 |
2×2 Low |
0.1 |
+5.1 |
|
Note 1: Test case is applicable (according to sub clause 8.1.2.1) to UE’s which, from the E-UTRA operating bands defined in Table 5.2-1, support only E-UTRA band 31. |
|||||||
8.5.1.2.2 FDD PHICH Transmit Diversity 4×2
8.5.1.2.2.1 Test purpose
This test verifies the demodulation performance of PHICH for transmit diversity with a given SNR for which the average probability of miss detection of Hybrid Indicator ("ACK to NACK") of the specified reference measurement channels remains below a specified value.
8.5.1.2.2.2 Test applicability
This test applies to all types of E-UTRA FDD UE release 8.
8.5.1.2.2.3 Minimum conformance requirements
The receiver characteristics of the PHICH are determined by the probability of miss-detecting an ACK for a NACK (Pm-an). It is assumed that there is no bias applied to the detection of ACK and NACK (zero-threshold detection).
Table 8.5.1.2.2.3-1: Test Parameters for PHICH
|
Parameter |
Unit |
Transmit diversity |
|
|
Downlink power allocation |
PDCCH_RA PHICH_RA OCNG_RA |
dB |
-3 |
|
PCFICH_RB PDCCH_RB PHICH_RB OCNG_RB |
dB |
-3 |
|
|
PHICH duration |
Normal |
||
|
Number of PHICH groups (Note 1) |
Ng = 1 |
||
|
PDCCH Content |
UL Grant should be included with the proper information aligned with A.3.6. |
||
|
Unused RE-s and PRB-s |
OCNG |
||
|
Cell ID |
0 |
||
|
|
dBm/15kHz |
-98 |
|
|
Cyclic prefix |
Normal |
||
|
Note 1: according to Clause 6.9 in TS 36.211 [8] Note 2: PHICH power settings refer to PHICH group power, i.e. the total power of all active PHICH sequences within a PHICH group. |
|||
at antenna portFor the parameters specified in Table 8.5.1.2.2.3-1 the average probability of a miss-detecting an ACK for a NACK (Pm-an) shall be below the specified value in Table 8.5.1.2.2.3-2.
Table 8.5.1.2.2.3-2: Minimum performance PHICH 4 Tx Antenna Port
|
Test number |
Bandwidth |
Reference Channel |
OCNG Pattern |
Propagation Condition |
Antenna configuration and correlation Matrix |
Reference value |
|
|
Pm-an (%) |
SNR (dB) |
||||||
|
1 |
10 MHz |
R.20A |
OP.1 FDD |
EVA5 |
4 x 2 Medium |
0.1 |
6.0 |
The normative reference for this requirement is TS 36.101 [2] clause 8.5.1.
8.5.1.2.2.4 Test description
8.5.1.2.2.4.1 Initial conditions
Test Environment: Normal as defined in TS 36.508 [7] clause 4.1.
Frequencies to be tested: Mid Range as defined in TS 36.508 [7] clause 4.3.1.1.
Channel Bandwidths to be tested: 10 MHz, as defined in TS 36.508 [7] clause 4.3.1.1
1. Connect the SS, the faders and AWGN noise sources to the UE antenna connector (s) as shown in TS 36.508 [7] Annex A, Figure A.11.
2. The parameter settings for the cell are set up according to Table 8.5.1.2.2.3-1.
3. Downlink signals are initially set up according to Annex C.1 and C.3.2 and uplink signals according to Annex H.1 and H.3.2.
4. Propagation conditions are set according to Annex B clauses B.0.
5. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 8.5.1.2.2.4.3.
8.5.1.2.2.4.2 Test procedure
1. Set the parameters of bandwidth, reference Channel, the propagation condition, antenna configuration, the correlation matrix and the SNR according to Table 8.5.1.2.2.5-1.
2. SS shall schedule PUSCH transmissions according to Annex A.2.2.1.1 Table A.2.2.1.1-1 to happen during 8 consecutive uplink TTIs via PDCCH DCI format 0 with new data indicator set to true. Since the UE has no payload, the UE shall send uplink MAC padding bits in PUSCH. SS upon receiving the PUSCH transmissions will transmit the associated ACKs. PHICH is set according to Annex 3.6 Table A.3.6-1. SS will only transmit PDCCH to schedule PUSCH transmission in the appropriate sub-frames. Table 8.5.1.2.2.4.2-1 indicates the transmissions for one cycle.
Table 8.5.1.2.2.4.2-1: PHICH test pattern
|
TTI |
1-4 |
5-8 |
9-12 |
13-16 |
17-20 |
21-24 |
|
PDCCH |
S |
S |
– |
– |
S |
S |
|
PHICH |
– |
– |
A |
A |
– |
– |
|
PUSCH |
T |
T |
R |
R |
T |
|
|
UL HARQ Process |
1-4 |
5-8 |
1-4 |
5-8 |
1-4 |
5-8 |
|
Note 1: This table gives an example test pattern for HARQ process for FDD PHICH test Note 2: Following notation is used: S: represents sending PDCCH DCI format 0 to schedule a future PUSCH transmission A: represents the ACK transmission on PHICH T: represents a scheduled PUSCH transmission R: represents a potential PUSCH re-transmission due to a missed ACK |
||||||
3. SS will only monitor for uplink retransmissions due to ACK missed-detections. Such re-transmissions (if they occur) will potentially happen in TTI 13 to 20. DTXs on TTI 13 to 20 are counted as successful ACK receptions while any transmission on these TTIs is counted as NACKs.
4. Repeat steps 1 – 3 for a duration sufficient to achieve statistical significance according to Annex G clause G.4 and measure Pm-an. Pm-an is (NACK) / (ACK + NACK). If Pm-an is less than the value specified in table 8.5.1.2.2.5-1, pass the UE. Otherwise fail the UE.
8.5.1.2.2.4.3 Message contents
Message contents are according to TS 36.508 [7] clause 4.6 with the following exceptions
Table 8.5.1.2.2.4.3-1: MAC-MainConfig-RBC
|
Derivation Path: TS 36.508 [7] clause 4.8.2.1.5, Table 4.8.2.1.5-1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
MAC-MainConfig-RBC ::= SEQUENCE { |
||||
|
dl-SCH-Config SEQUENCE {} |
Not present |
|||
|
ul-SCH-Config SEQUENCE { |
||||
|
maxHARQ-Tx |
n2 |
Only one retransmission per UL HARQ |
||
8.5.1.2.2.5 Test requirement
For the parameters specified in Table 8.5.1.2.2.3-1 the average probability of a miss-detecting ACK for NACK (Pm-dsg) shall be below the specified value in Table 8.5.1.2.2.5-1.
Table 8.5.1.2.2.5-1: Test requirement PHICH 4 Tx Antenna Port
|
Test number |
Bandwidth |
Reference Channel |
OCNG Pattern |
Propagation Condition |
Antenna configuration and correlation Matrix |
Reference value |
|
|
Pm-an (%) |
SNR (dB) |
||||||
|
1 |
10 MHz |
R.20A |
OP.1 FDD |
EVA5 |
4 x 2 Medium |
0.1 |
7.0 |
8.5.1.2.2_1 FDD PHICH Transmit Diversity 4×2 (Release 9 and forward)
8.5.1.2.2_1.1 Test purpose
This test verifies the demodulation performance of PHICH for transmit diversity with a given SNR for which the average probability of miss detection of Hybrid Indicator ("ACK to NACK") of the specified reference measurement channels remains below a specified value.
8.5.1.2.2_1.2 Test applicability
This test applies to all types of E-UTRA FDD UE release 9 and forward.
8.5.1.2.2_1.3 Minimum conformance requirements
The receiver characteristics of the PHICH are determined by the probability of miss-detecting an ACK for a NACK (Pm-an). It is assumed that there is no bias applied to the detection of ACK and NACK (zero-threshold detection).
Table 8.5.1.2.2_1.3-1: Test Parameters for PHICH
|
Parameter |
Unit |
Transmit diversity |
|
|
Downlink power allocation |
PDCCH_RA PHICH_RA OCNG_RA |
dB |
-3 |
|
PCFICH_RB PDCCH_RB PHICH_RB OCNG_RB |
dB |
-3 |
|
|
PHICH duration |
Normal |
||
|
Number of PHICH groups (Note 1) |
Ng = 1 |
||
|
PDCCH Content |
UL Grant should be included with the proper information aligned with A.3.6. |
||
|
Unused RE-s and PRB-s |
OCNG |
||
|
Cell ID |
0 |
||
|
|
dBm/15kHz |
-98 |
|
|
Cyclic prefix |
Normal |
||
|
Note 1: according to Clause 6.9 in TS 36.211 [8] Note 2: PHICH power settings refer to PHICH group power, i.e. the total power of all active PHICH sequences within a PHICH group. |
|||
For the parameters specified in Table 8.5.1.2.2_1.3-1 the average probability of a miss-detecting an ACK for a NACK (Pm-an) shall be below the specified value in Table 8.5.1.2.2_1.3-2.
Table 8.5.1.2.2_1.3-2: Minimum performance PHICH 4 Tx Antenna Port
|
Test number |
Bandwidth |
Reference Channel |
OCNG Pattern |
Propagation Condition |
Antenna configuration and correlation Matrix |
Reference value |
|
|
Pm-an (%) |
SNR (dB) |
||||||
|
1 |
5 MHz |
R.20 |
OP.1 FDD |
EPA5 |
4 x 2 Medium |
0.1 |
6.1 |
The normative reference for this requirement is TS 36.101 [2] clause 8.5.1.
8.5.1.2.2_1.4 Test description
8.5.1.2.2_1.4.1 Initial conditions
Test Environment: Normal as defined in TS 36.508 [7] clause 4.1.
Frequencies to be tested: Mid Range as defined in TS 36.508 [7] clause 4.3.1.1.
Channel Bandwidths to be tested: 5 MHz, as defined in TS 36.508 [7] clause 4.3.1.1
1. Connect the SS, the faders and AWGN noise sources to the UE antenna connector (s) as shown in TS 36.508 [7] Annex A, Figure A.11.
2. The parameter settings for the cell are set up according to Table 8.5.1.2.2_1.3-1.
3. Downlink signals are initially set up according to Annex C.1 and C.3.2 and uplink signals according to Annex H.1 and H.3.2.
4. Propagation conditions are set according to Annex B clauses B.0.
5. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 8.5.1.2.2_1.4.3.
8.5.1.2.2_1.4.2 Test procedure
1. Set the parameters of bandwidth, reference Channel, the propagation condition, antenna configuration, the correlation matrix and the SNR according to Table 8.5.1.2.2_1.5-1.
2. SS shall schedule PUSCH transmissions according to Annex A.2.2.1.1 Table A.2.2.1.1-1 to happen during 8 consecutive uplink TTIs via PDCCH DCI format 0 with new data indicator set to true. Since the UE has no payload, the UE shall send uplink MAC padding bits in PUSCH. SS upon receiving the PUSCH transmissions will transmit the associated ACKs. PHICH is set according to Annex 3.6 Table A.3.6-1. SS will only transmit PDCCH to schedule PUSCH transmission in the appropriate sub-frames. Table 8.5.1.2.2_1.4.2-1 indicates the transmissions for one cycle.
Table 8.5.1.2.2_1.4.2-1: PHICH test pattern
|
TTI |
1-4 |
5-8 |
9-12 |
13-16 |
17-20 |
21-24 |
|
PDCCH |
S |
S |
– |
– |
S |
S |
|
PHICH |
– |
– |
A |
A |
– |
– |
|
PUSCH |
T |
T |
R |
R |
T |
|
|
UL HARQ Process |
1-4 |
5-8 |
1-4 |
5-8 |
1-4 |
5-8 |
|
Note 1: This table gives an example test pattern for HARQ process for FDD PHICH test Note 2: Following notation is used: S: represents sending PDCCH DCI format 0 to schedule a future PUSCH transmission A: represents the ACK transmission on PHICH T: represents a scheduled PUSCH transmission R: represents a potential PUSCH re-transmission due to a missed ACK |
||||||
3. SS will only monitor for uplink retransmissions due to ACK missed-detections. Such re-transmissions (if they occur) will potentially happen in TTI 13 to 20. DTXs on TTI 13 to 20 are counted as successful ACK receptions while any transmission on these TTIs is counted as NACKs.
4. Repeat steps 1 – 3 for a duration sufficient to achieve statistical significance according to Annex G clause G.4 and measure Pm-an. Pm-an is (NACK) / (ACK + NACK). If Pm-an is less than the value specified in table 8.5.1.2.2_1.5-1, pass the UE. Otherwise fail the UE.
8.5.1.2.2_1.4.3 Message contents
Message contents are according to TS 36.508 [7] clause 4.6 with the following exceptions
Table 8.5.1.2.2_1.4.3-1: MAC-MainConfig-RBC
|
Derivation Path: TS 36.508 [7] clause 4.8.2.1.5, Table 4.8.2.1.5-1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
MAC-MainConfig-RBC ::= SEQUENCE { |
||||
|
dl-SCH-Config SEQUENCE {} |
Not present |
|||
|
ul-SCH-Config SEQUENCE { |
||||
|
maxHARQ-Tx |
n2 |
Only one retransmission per UL HARQ |
||
8.5.1.2.2_1.5 Test requirement
For the parameters specified in Table 8.5.1.2.2_1.3-1 the average probability of a miss-detecting ACK for NACK (Pm-dsg) shall be below the specified value in Table 8.5.1.2.2_1.5-1.
Table 8.5.1.2.2_1.5-1: Test requirement PHICH 4 Tx Antenna Port
|
Test number |
Bandwidth |
Reference Channel |
OCNG Pattern |
Propagation Condition |
Antenna configuration and correlation Matrix |
Reference value |
|
|
Pm-an (%) |
SNR (dB) |
||||||
|
1 |
5 MHz |
R.20 |
OP.1 FDD |
EPA5 |
4 x 2 Medium |
0.1 |
+7.1 |
8.5.1.2.3
8.5.1.2.3_A
8.5.1.2.3_B
8.5.1.2.3_C FDD PHICH Transmit Diversity 2×2 for eICIC
8.5.1.2.3_C.1 FDD PHICH Transmit Diversity 2×2 for eICIC (non-MBSFN ABS)
8.5.1.2.3_C.1.1 Test purpose
This test verifies the demodulation performance of PHICH for transmit diversity with a given SNR for which the average probability of miss detection of Hybrid Indicator ("ACK to NACK") of the specified reference measurement channels remains below a specified value.
8.5.1.2.3_C.1.2 Test applicability
This test applies to all types of E-UTRA FDD UE release 10 and forward. Applicability requires support for FGI bit 115.
8.5.1.2.3_C.1.3 Minimum conformance requirements
The receiver characteristics of the PHICH are determined by the probability of miss-detecting an ACK for a NACK (Pm-an). It is assumed that there is no bias applied to the detection of ACK and NACK (zero-threshold detection).
Table 8.5.1.2.3_C.1.3-1: Test Parameters for PHICH
|
Parameter |
Unit |
Unit |
Cell 1 |
Cell 2 |
|||
|
Downlink power allocation |
PDCCH_RA PHICH_RA OCNG_RA |
dB |
-3 |
-3 |
|||
|
PCFICH_RB PDCCH_RB PHICH_RB OCNG_RB |
dB |
-3 |
-3 |
||||
|
|
|
dBm/15kHz |
-100.5 (Note 1) |
N/A |
|||
|
|
dBm/15kHz |
-98 (Note 2) |
N/A |
||||
|
|
dBm/15kHz |
-95.3 (Note 3) |
N/A |
||||
|
|
dB |
Reference Value in Table 8.5.1.2.3_C.1.3-2 |
1.5 |
||||
|
BWChannel |
MHz |
10 |
10 |
||||
|
Subframe Configuration |
Non-MBSFN |
Non-MBSFN |
|||||
|
Time Offset between Cells |
μs |
2.5 (synchronous cells) |
|||||
|
Cell Id |
0 |
1 |
|||||
|
ABS pattern (Note 4) |
N/A |
00000100 00000100 00000100 01000100 00000100 |
|||||
|
RLM/RRM Measurement Subframe Pattern (Note 5) |
00000100 00000100 00000100 00000100 00000100 |
N/A |
|||||
|
CSI Subframe Sets (Note 6) |
CCSI,0 |
00000100 00000100 00000100 01000100 00000100 |
N/A |
||||
|
CCSI,1 |
11111011 11111011 11111011 10111011 11111011 |
N/A |
|||||
|
Number of control OFDM symbols |
3 |
3 |
|||||
|
Number of PHICH groups (Ng) |
1 |
N/A |
|||||
|
PHICH duration |
extended |
N/A |
|||||
|
Unused RE-s and PRB-s |
OCNG |
OCNG |
|||||
|
Cyclic prefix |
Normal |
Normal |
|||||
|
Note 1: This noise is applied in OFDM symbols #1, #2, #3, #5, #6, #8, #9, #10,#12, #13 of a subframe overlapping with the aggressor ABS Note 2: This noise is applied in OFDM symbols #0, #4, #7, #11 of a subframe overlapping with the aggressor ABS Note 3: This noise is applied in OFDM symbols of a subframe overlapping with aggressor non-ABS Note 4: ABS pattern as defined in [14]. PHICH is transmitted in the serving cell subframe when the subframe is overlapped with the ABS subframe of aggressor cell but not in the 26th subframe indicated by the ABS pattern. Note 5: Time-domain measurement resource restriction pattern for PCell measurements as defined in [5] Note 6: As configured according to the time-domain measurement resource restriction pattern for CSI measurements defined in [5] Note 7: Cell 1 is the serving cell. Cell 2 is the aggressor cell. The number of the CRS ports in Cell1 and Cell2 is the same. Note 8: SIB-1 will not be transmitted in Cell2 in the test. |
|||||||
at antenna port
For the parameters specified in Table 8.5.1.2.3_C.1.3-1, the average probability of a miss-detecting an ACK for a NACK (Pm-an) shall be below the specified value in Table 8.5.1.2.3_C.1.3-2. In Table 8.5.1.2.3_C.1.3-1, Cell 1 is the serving cell, and Cell 2 is the aggressor cell. The downlink physical channel setup for Cell 1 is according to Annex C.3.2 and for Cell 2 is according to Annex C.3.3, respectively.
Table 8.5.1.2.3_C.1.3-2: Minimum performance PHICH
|
Test Number |
Reference Channel |
OCNG Pattern |
Propagation Conditions (Note 1) |
Antenna Configuration and Correlation Matrix |
Reference Value |
|||
|
Cell 1 |
Cell 2 |
Cell 1 |
Cell 2 |
Pm-an (%) |
SNR (dB) (Note 2) |
|||
|
1 |
R.19 |
OP.1 FDD |
OP.1 FDD |
EPA5 |
EPA5 |
2×2 Low |
0.1 |
4.6 |
|
Note 1: The propagation conditions for Cell 1 and Cell 2 are statistically independent. Note 2: SNR corresponds to Note 3: The correlation matrix and antenna configuration apply for Cell 1 and Cell 2. |
||||||||
of cell 1. The normative reference for this requirement is TS 36.101 [2] clause 8.5.1.2.3.
8.5.1.2.3_C.1.4 Test description
8.5.1.2.3_C.1.4.1 Initial conditions
Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.
Test Environment: Normal as defined in TS 36.508 [7] clause 4.1.
Frequencies to be tested: Mid Range as defined in TS 36.508 [7] clause 4.3.1.1.
Channel Bandwidths to be tested: 10 MHz, as defined in TS 36.508 [7] clause 4.3.1.1
1. Connect the SS, the faders and AWGN noise sources to the UE antenna connector (s) as shown in TS 36.508 [7] Annex A, Figure A.40 for antenna transmit diversity 2×2 configuration.
2. The parameter settings for the cell are set up according to Table 8.5.1.2.3_C.1.3-1 and 8.5.1.2.3_C.1.3-2.
3. Downlink signals are initially set up according to Annex C.0, C.1, C.3.2 and C.3.3 and uplink signals according to Annex H.1 and H.3.2.
4. Propagation conditions are set according to Annex B clauses B.0.
5. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 8.5.1.2.3_C.1.4.3.
8.5.1.2.3_C.1.4.2 Test procedure
1. Set the parameters for Cell1 and Cell2 according to Tables 8.5.1.2.3_C.1.5-1, 8.5.1.2.3_C.1.5-2, C.3.3-1 of Annex C.3.3 as appropriate. Propagation conditions are set according to Annex B clause B.2.
2. SS shall schedule PUSCH transmissions according to Annex A.2.2.1.1 Table A.2.2.1.1-1 via PDCCH DCI format 0 with the new data indicator set to true. Since the UE has no payload, the UE shall send uplink MAC padding bits in PUSCH. SS upon receiving the PUSCH transmission will transmit the associated ACK. PHICH is set according to Annex 3.6 Table A.3.6-1. SS will only transmit PDCCH to schedule PUSCH transmission in the appropriateTTI-s. Table 8.5.1.2.3_C.1.4.2-1 indicates the transmissions for two cycles.
Table 8.5.1.2.3_C.1.4.2-1: PHICH test pattern
|
TTI |
6 |
10 |
14 |
18 |
22 |
26 |
30 |
34 |
38 |
|
PDCCH |
S |
– |
– |
– |
S |
– |
– |
– |
S |
|
PUSCH |
– |
T |
– |
R |
– |
T |
– |
R |
– |
|
PHICH |
– |
– |
A |
– |
– |
– |
A |
– |
– |
|
Note 1: This table gives an example test pattern for HARQ process for FDD PHICH test Note 2: Following notation is used: Note 3: In the other TTI-s there are no DCI-0, PHICH and PUSCH transmissions |
|||||||||
3. SS will monitor for uplink retransmissions due to ACK missed-detection. Such re-transmission (if it occurs) will potentially happen in TTI 18 (34 and so on). DTX from the UE side on this TTI is counted as successful ACK receptions while any transmission on this TTI is counted as NACK.
4. Repeat steps 1 – 3 for a duration sufficient to achieve statistical significance according to Annex G clause G.4 and measure Pm-an. Pm-an is (NACK) / (ACK + NACK).
If Pm-an is less than the value specified in table 8.5.1.2.3_C.1.5-2, pass the UE. Otherwise fail the UE.
8.5.1.2.3_C.1.4.3 Message contents
Message contents are according to TS 36.508 [7] clause 4.6 with the following exceptions
Table 8.5.1.2.3_C.1.4.3-1: PHICH-Config
|
Derivation Path: TS 36.508 [7] clause 4.6.3, Table 4.6.3-4 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
PHICH-Config-DEFAULT ::= SEQUENCE { |
|||
|
phich-Duration |
extended |
Cell 1 |
|
|
phich-Resource |
one |
||
|
} |
|||
Table 8.5.1.2.3_C.1.4.3-2: MAC-MainConfig-RBC
|
Derivation Path: TS 36.508 [7] clause 4.8.2.1.5, Table 4.8.2.1.5-1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
MAC-MainConfig-RBC ::= SEQUENCE { |
||||
|
dl-SCH-Config SEQUENCE {} |
Not present |
|||
|
ul-SCH-Config SEQUENCE { |
||||
|
maxHARQ-Tx |
n2 |
Only one retransmission per UL HARQ |
||
Table 8.5.1.2.3_C.1.4.3-3: RadioResourceConfigDedicated-SRB2-DRB(n, m)
|
Derivation Path: TS 36.508 [7] clause 4.6.3, Table 4.6.3-16 RadioResourceConfigDedicated-SRB2-DRB(n,m) |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RadioResourceConfigDedicated-SRB2-DRB(n, m) ::= SEQUENCE { |
|||
|
MeasSubframePatternPCell-r10 CHOICE { |
|||
|
setup SEQUENCE { |
|||
|
subframePatternFDD-r10 |
‘0000010000000100000001000000010000000100’ |
BIT STRING (SIZE (40)) |
|
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.5.1.2.3_C.1.4.3-4: CQI-ReportConfig-r10-DEFAULT
|
Derivation Path: 36.508 [7] clause 4.6.3, Table 4.6.3-2AA CQI-ReportConfig-r10-DEFAULT |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
CQI-ReportConfig-r10-DEFAULT ::= SEQUENCE { |
|||
|
cqi-ReportAperiodic-r10 |
Not present |
||
|
nomPDSCH-RS-EPRE-Offset |
0 |
||
|
cqi-ReportPeriodic-r10 |
Not present |
||
|
pmi-RI-Report-r9 |
Not present |
||
|
csi-SubframePatternConfig-r10 CHOICE { |
|||
|
setup SEQUENCE { |
|||
|
csi-MeasSubframeSet1-r10 CHOICE { |
|||
|
subframePatternFDD-r10 |
‘0000010000000100000001000100010000000100’ |
BIT STRING (SIZE (40)) |
|
|
} |
|||
|
csi-MeasSubframeSet2-r10 CHOICE { |
|||
|
subframePatternFDD-r10 |
‘1111101111111011111110111011101111111011’ |
BIT STRING (SIZE (40)) |
|
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
8.5.1.2.3_C.1.5 Test requirement
For the parameters specified in Table 8.5.1.2.3_C.1.5-1, the average probability of a miss-detecting ACK for NACK (Pm-dsg) shall be below the specified value in Table 8.5.1.2.3_C.1.5-2.
Table 8.5.1.2.3_C.1.5-1: Test Parameters for PHICH
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
||||
|
Downlink power allocation |
PDCCH_RA PHICH_RA OCNG_RA |
dB |
-3 |
-3 |
|||
|
PCFICH_RB PDCCH_RB PHICH_RB OCNG_RB |
dB |
-3 |
-3 |
||||
|
|
|
dBm/15kHz |
-100.6 (Note 1) |
N/A |
|||
|
|
dBm/15kHz |
-98 (Note 2) |
N/A |
||||
|
|
dBm/15kHz |
-95.4 (Note 3) |
N/A |
||||
|
|
dB |
Reference Value in Table 8.5.1.2.3_C.1.5-2 |
1.3 |
||||
|
BWChannel |
MHz |
10 |
10 |
||||
|
Subframe Configuration |
Non-MBSFN |
Non-MBSFN |
|||||
|
Time Offset between Cells |
μs |
2.5 (synchronous cells) |
|||||
|
Cell Id |
0 |
1 |
|||||
|
ABS pattern (Note 4) |
N/A |
00000100 00000100 00000100 01000100 00000100 |
|||||
|
RLM/RRM Measurement Subframe Pattern (Note 5) |
00000100 00000100 00000100 00000100 00000100 |
N/A |
|||||
|
CSI Subframe Sets (Note 6) |
CCSI,0 |
00000100 00000100 00000100 01000100 00000100 |
N/A |
||||
|
CCSI,1 |
11111011 11111011 11111011 10111011 11111011 |
N/A |
|||||
|
Number of control OFDM symbols |
3 |
3 |
|||||
|
Number of PHICH groups (Ng) |
1 |
N/A |
|||||
|
PHICH duration |
extended |
N/A |
|||||
|
Unused RE-s and PRB-s |
OCNG |
OCNG |
|||||
|
Cyclic prefix |
Normal |
Normal |
|||||
|
Note 1: This noise is applied in OFDM symbols #1, #2, #3, #5, #6, #8, #9, #10,#12, #13 of a subframe overlapping with the aggressor ABS Note 2: This noise is applied in OFDM symbols #0, #4, #7, #11 of a subframe overlapping with the aggressor ABS Note 3: This noise is applied in OFDM symbols of a subframe overlapping with aggressor non-ABS Note 4: ABS pattern as defined in [14]. PHICH is transmitted in the serving cell subframe when the subframe is overlapped with the ABS subframe of aggressor cell but not in the 26th subframe indicated by the ABS pattern. Note 5: Time-domain measurement resource restriction pattern for PCell measurements as defined in [5] Note 6: As configured according to the time-domain measurement resource restriction pattern for CSI measurements defined in [5] Note 7: Cell 1 is the serving cell. Cell 2 is the aggressor cell. The number of the CRS ports in Cell1 and Cell2 is the same. Note 8: SIB-1 will not be transmitted in Cell2 in the test. |
|||||||
at antenna port
Table 8.5.1.2.3_C.1.5-2: Test requirement FDD PHICH Transmit Diversity 2×2 for eICIC (non-MBSFN ABS)
|
Test Number |
Reference Channel |
OCNG Pattern |
Propagation Conditions (Note 1) |
Antenna Configuration and Correlation Matrix |
Reference Value |
|||
|
Cell 1 |
Cell 2 |
Cell 1 |
Cell 2 |
Pm-an (%) |
SNR (dB) (Note 2) |
|||
|
1 |
R.19 |
OP.1 FDD |
OP.1 FDD |
EPA5 |
EPA5 |
2×2 Low |
0.1 |
5.5 |
|
Note 1: The propagation conditions for Cell 1 and Cell 2 are statistically independent. Note 2: SNR corresponds to Note 3: The correlation matrix and antenna configuration apply for Cell 1 and Cell 2. |
||||||||
of cell 1. 8.5.1.2.3_D
8.5.1.2.3_E FDD PHICH Transmit Diversity 2×2 for feICIC
8.5.1.2.3_E.1 FDD PHICH Transmit Diversity 2×2 for feICIC (non-MBSFN ABS)
8.5.1.2.3_E.1.1 Test purpose
This test verifies the demodulation performance of PHICH for transmit diversity with a given SNR for which the average probability of miss detection of Hybrid Indicator ("ACK to NACK") of the specified reference measurement channels remains below a specified value where PHICH transmission subframes overlap with ABS of the aggressor cell.
8.5.1.2.3_E.1.2 Test applicability
This test applies to all types of E-UTRA FDD UE and CRS interference handling – UE Category ≥2 release 11 and forward. Applicability requires support of FGI bit 115.
8.5.1.2.3_E.1.3 Minimum conformance requirements
The receiver characteristics of the PHICH are determined by the probability of miss-detecting an ACK for a NACK (Pm-an). It is assumed that there is no bias applied to the detection of ACK and NACK (zero-threshold detection).
Table 8.5.1.2.3_E.1.3-1: Test Parameters for PHICH
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
||
|
Downlink power allocation |
PDCCH_RA PHICH_RA OCNG_RA |
dB |
-3 |
-3 |
-3 |
|
|
PCFICH_RB PDCCH_RB PHICH_RB OCNG_RB |
dB |
-3 |
-3 |
-3 |
||
|
at antenna port
|
 |
dBm/15kHz |
-98 (Note 1) |
N/A |
N/A |
|
 |
dBm/15kHz |
-98 (Note 2) |
N/A |
N/A |
||
 |
dBm/15kHz |
-93 (Note 3) |
N/A |
N/A |
||
 |
dB |
Reference Value in Table 8.5.1.2.3_E.1.3-2 |
5 |
3 |
||
|
BWChannel |
MHz |
10 |
10 |
10 |
||
|
Subframe Configuration |
Non-MBSFN |
Non-MBSFN |
Non-MBSFN |
|||
|
Time Offset between Cells |
μs |
N/A |
3 |
-1 |
||
|
Frequency shift between Cells |
Hz |
N/A |
300 |
-100 |
||
|
Cell Id |
0 |
126 |
1 |
|||
|
PDCCH Content |
UL Grant should be included with the proper information aligned with A.3.6. |
N/A |
N/A |
|||
|
ABS pattern (Note 4) |
N/A |
00000100 00000100 00000100 00000100 00000100 |
00000100 00000100 00000100 00000100 00000100 |
|||
|
RLM/RRM Measurement Subframe Pattern (Note 5) |
00000100 00000100 00000100 00000100 00000100 |
N/A |
N/A |
|||
|
CSI Subframe Sets (Note 6) |
CCSI,0 |
00000100 00000100 00000100 00000100 00000100 |
N/A |
N/A |
||
|
CCSI,1 |
11111011 11111011 11111011 11111011 11111011 |
N/A |
N/A |
|||
|
Number of control OFDM symbols |
2 |
Note 7 |
Note 7 |
|||
|
Number of PHICH groups (Ng) |
1 |
N/A |
N/A |
|||
|
PHICH duration |
Normal |
N/A |
N/A |
|||
|
Unused RE-s and PRB-s |
OCNG |
OCNG |
OCNG |
|||
|
Cyclic prefix |
Normal |
Normal |
Normal |
|||
|
Note 1: This noise is applied in OFDM symbols #1, #2, #3, #5, #6, #8, #9, #10,#12, #13 of a subframe overlapping with the aggressor ABS Note 2: This noise is applied in OFDM symbols #0, #4, #7, #11 of a subframe overlapping with the aggressor ABS Note 3: This noise is applied in OFDM symbols of a subframe overlapping with aggressor non-ABS Note 4: ABS pattern as defined in [9]. PHICH is transmitted in the serving cell subframe when the subframe is overlapped with the ABS subframe of aggressor cell but not in the 26th subframe indicated by the ABS pattern. Note 5: Time-domain measurement resource restriction pattern for PCell measurements as defined in [7] Note 6: As configured according to the time-domain measurement resource restriction pattern for CSI measurements defined in [7] Note 7: The number of control OFDM symbols is not available for ABS and is 2 for the subframe indicated by “0” of ABS pattern. Note 8: The number of the CRS ports in Cell 1, Cell 2 and Cell 3 is the same. Note 9: SIB-1 will not be transmitted in Cell 2 and Cell 3 in the test. |
||||||
For the parameters specified in Table 8.5.1.2.3_E.1.3-1, the average probability of a miss-detecting an ACK for a NACK (Pm-an) shall be below the specified value in Table 8.5.1.2.3_E.1.3-2. In Table 8.5.1.2.3_E.1.3-1, Cell 1 is the serving cell, and Cell 2 and Cell 3 are the aggressor cell. The downlink physical channel setup for Cell 1 is according to Annex C.3.2 and for Cell 2 and Cell 3 is according to Annex C.3.3, respectively. The CRS assistance information is provided for Cell 2 and Cell 3.
Table 8.5.1.2.3_E.1.3-2: Minimum performance PHICH 2 Tx Antenna Port
|
Test Number |
Reference Channel |
OCNG Pattern |
Propagation Conditions (Note 1) |
Antenna Configuration and Correlation Matrix (Note 2) |
Reference Value |
|||||
|
Cell 1 |
Cell 2 |
Cell 3 |
Cell 1 |
Cell 2 |
Cell 3 |
Pm-an (%) |
SNR (dB) (Note 3) |
|||
|
1 |
R.19 |
OP.1 FDD |
OP.1 FDD |
OP.1 FDD |
EPA5 |
EVA5 |
EVA5 |
2×2 Low |
0.1 |
5.0 |
|
Note 1: The propagation conditions for Cell 1, Cell 2 and Cell 3 are statistically independent. Note 2: The correlation matrix and antenna configuration apply for Cell 1, Cell 2 and Cell 3. Note 3: SNR corresponds to of Cell 1.
|
||||||||||
The normative reference for this requirement is TS 36.101 [2] clause 8.5.1.2.4.
8.5.1.2.3_E.1.4 Test description
8.5.1.2.3_E.1.4.1 Initial conditions
Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.
Test Environment: Normal as defined in TS 36.508 [7] clause 4.1.
Frequencies to be tested: Mid Range as defined in TS 36.508 [7] clause 4.3.1.1.
Channel Bandwidths to be tested: 10 MHz, as defined in TS 36.508 [7] clause 4.3.1.1
1. Connect the SS, the faders and AWGN noise sources to the UE antenna connector (s) as shown in TS 36.508 [7] Annex A, Figure A.48 for antenna transmit diversity 2×2 configuration.
2. The parameter settings for the cell are set up according to Table 8.5.1.2.3_E.1.3-1 and 8.5.1.2.3_E.1.3-2.
3. Downlink signals are initially set up according to Annex C.0, C.1, C.3.2 and C.3.3 and uplink signals according to Annex H.1 and H.3.2.
4. Propagation conditions are set according to Annex B clauses B.0.
5. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2 with exceptions listed in 5.2A.5. Message contents are defined in clause 8.5.1.2.3_E.1.4.3.
8.5.1.2.3_E.1.4.2 Test procedure
1. Set the parameters for Cell1, Cell2 and Cell3 according to Tables 8.5.1.2.3_E.1.3-1, 8.5.1.2.3_E.1.5-1 and C.3.3-2 of Annex C.3.3 as appropriate. Propagation conditions are set according to Annex B clause B.2.
2. SS shall schedule PUSCH transmissions according to Annex A.2.2.1.1 Table A.2.2.1.1-1 via PDCCH DCI format 0 with the new data indicator set to true. Since the UE has no payload, the UE shall send uplink MAC padding bits in PUSCH. SS upon receiving the PUSCH transmission will transmit the associated ACK. PHICH is set according to Annex 3.6 Table A.3.6-1. SS will only transmit PDCCH to schedule PUSCH transmission in the appropriateTTI-s. Table 8.5.1.2.3_E.1.4.2-1 indicates the transmissions for two cycles.
Table 8.5.1.2.3_E.1.4.2-1: PHICH test pattern
|
TTI |
6 |
10 |
14 |
18 |
22 |
26 |
30 |
34 |
38 |
|
PDCCH |
S |
– |
– |
– |
S |
– |
– |
– |
S |
|
PUSCH |
– |
T |
– |
R |
– |
T |
– |
R |
– |
|
PHICH |
– |
– |
A |
– |
– |
– |
A |
– |
– |
|
Note 1: This table gives an example test pattern for HARQ process for FDD PHICH test Note 2: Following notation is used: Note 3: In the other TTI-s there are no DCI-0, PHICH and PUSCH transmissions |
|||||||||
3. SS will monitor for uplink retransmissions due to ACK missed-detection. Such re-transmission (if it occurs) will potentially happen in TTI 18 (34 and so on). DTX from the UE side on this TTI is counted as successful ACK receptions while any transmission on this TTI is counted as NACK.
4. Repeat steps 1 – 3 for a duration sufficient to achieve statistical significance according to Annex G clause G.4 and measure Pm-an in the subframes overlapping with ABS of the aggressor cell. Pm-an is (NACK) / (ACK + NACK).
If Pm-an is less than the value specified in table 8.5.1.2.3_E.1.5-2, pass the UE. Otherwise fail the UE.
8.5.1.2.3_E.1.4.3 Message contents
Message contents are according to TS 36.508 [7] clause 5.2A.5.1 with the following exceptions
Table 8.5.1.2.3_E.1.4.3-1: MAC-MainConfig-RBC
|
Derivation Path: TS 36.508 [7] clause 4.8.2.1.5, Table 4.8.2.1.5-1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
MAC-MainConfig-RBC ::= SEQUENCE { |
||||
|
dl-SCH-Config SEQUENCE {} |
Not present |
|||
|
ul-SCH-Config SEQUENCE { |
||||
|
maxHARQ-Tx |
n2 |
Only one retransmission per UL HARQ |
||
Table 8.5.1.2.3_E.1.4.3-2: RadioResourceConfigDedicated-SRB2-DRB(n, m)
|
Derivation Path: TS 36.508 [7] clause 4.6.3, Table 4.6.3-16 RadioResourceConfigDedicated-SRB2-DRB(n,m) |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RadioResourceConfigDedicated-SRB2-DRB(n, m) ::= SEQUENCE { |
|||
|
MeasSubframePatternPCell-r10 CHOICE { |
|||
|
setup SEQUENCE { |
|||
|
subframePatternFDD-r10 |
‘0000010000000100000001000000010000000100’ |
BIT STRING (SIZE (40)) |
|
|
} |
|||
|
} |
|||
|
neighCellsCRS-Info-r11 ::= CHOICE { |
|||
|
setup SEQUENCE { |
|||
|
CRS-AssistancedInfoList-r11 ::= SEQUENCE (SIZE (1..maxCellReport)) OF CRS-AssistanceInfo-r11{ |
2 entries |
||
|
CRS-AssistancedInfo-r11 ::= SEQUENCE { |
|||
|
physCellId-r11 |
126 |
Cell 2 |
|
|
1 |
Cell 3 |
||
|
antennaPortsCount-r11 |
an2 |
Cell 2, Cell 3 |
|
|
mbsfn-SubframeConfigList-r11::= SEQUENCE (SIZE (1..maxMBSFN-Allocations)) OF MBSFN-SubframeConfig{ |
Cell 2, Cell 3 |
||
|
MBSFN-SubframeConfig:: = SEQUENCE { |
|||
|
radioframeAllocationPeriod |
n1 |
||
|
radioframeAllocationOffset |
0 |
||
|
subframeAllocation CHOICE{ |
|||
|
oneFrame |
‘000000’ B |
non-MBSFN |
|
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.5.1.2.3_E.1.4.3-3: CQI-ReportConfig-r10-DEFAULT
|
Derivation Path: 36.508 [7] clause 4.6.3, Table 4.6.3-2AA CQI-ReportConfig-r10-DEFAULT |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
CQI-ReportConfig-r10-DEFAULT ::= SEQUENCE { |
|||
|
cqi-ReportAperiodic-r10 |
Not present |
||
|
nomPDSCH-RS-EPRE-Offset |
0 |
||
|
cqi-ReportPeriodic-r10 |
Not present |
||
|
pmi-RI-Report-r9 |
Not present |
||
|
csi-SubframePatternConfig-r10 CHOICE { |
|||
|
setup SEQUENCE { |
|||
|
csi-MeasSubframeSet1-r10 CHOICE { |
|||
|
subframePatternFDD-r10 |
‘0000010000000100000001000000010000000100’ |
BIT STRING (SIZE (40)) |
|
|
} |
|||
|
csi-MeasSubframeSet2-r10 CHOICE { |
|||
|
subframePatternFDD-r10 |
‘1111101111111011111110111111101111111011’ |
BIT STRING (SIZE (40)) |
|
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
8.5.1.2.3_E.1.5 Test requirement
For the parameters specified in Table 8.5.1.2.3_E.1.5-1, the average probability of a miss-detecting ACK for NACK (Pm-dsg) shall be below the specified value in Table 8.5.1.2.3_E.1.5-2.
Table 8.5.1.2.3_E.1.5-1: Test Parameters for PHICH
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
||
|
Downlink power allocation |
PDCCH_RA PHICH_RA OCNG_RA |
dB |
-3 |
-3 |
-3 |
|
|
PCFICH_RB PDCCH_RB PHICH_RB OCNG_RB |
dB |
-3 |
-3 |
-3 |
||
|
at antenna port
|
 |
dBm/15kHz |
-98 (Note 1) |
N/A |
N/A |
|
 |
dBm/15kHz |
-98 (Note 2) |
N/A |
N/A |
||
 |
dBm/15kHz |
-93.1 (Note 3) |
N/A |
N/A |
||
 |
dB |
Reference Value in Table 8.5.1.2.3_E.1.5-2 |
4.8 |
2.8 |
||
|
BWChannel |
MHz |
10 |
10 |
10 |
||
|
Subframe Configuration |
Non-MBSFN |
Non-MBSFN |
Non-MBSFN |
|||
|
Time Offset between Cells |
μs |
N/A |
3 |
-1 |
||
|
Frequency shift between Cells |
Hz |
N/A |
300 |
-100 |
||
|
Cell Id |
0 |
126 |
1 |
|||
|
PDCCH Content |
UL Grant should be included with the proper information aligned with A.3.6. |
N/A |
N/A |
|||
|
ABS pattern (Note 4) |
N/A |
00000100 00000100 00000100 00000100 00000100 |
00000100 00000100 00000100 00000100 00000100 |
|||
|
RLM/RRM Measurement Subframe Pattern (Note 5) |
00000100 00000100 00000100 00000100 00000100 |
N/A |
N/A |
|||
|
CSI Subframe Sets (Note 6) |
CCSI,0 |
00000100 00000100 00000100 00000100 00000100 |
N/A |
N/A |
||
|
CCSI,1 |
11111011 11111011 11111011 11111011 11111011 |
N/A |
N/A |
|||
|
Number of control OFDM symbols |
2 |
Note 7 |
Note 7 |
|||
|
Number of PHICH groups (Ng) |
1 |
N/A |
N/A |
|||
|
PHICH duration |
Normal |
N/A |
N/A |
|||
|
Unused RE-s and PRB-s |
OCNG |
OCNG |
OCNG |
|||
|
Cyclic prefix |
Normal |
Normal |
Normal |
|||
|
Note 1: This noise is applied in OFDM symbols #1, #2, #3, #5, #6, #8, #9, #10,#12, #13 of a subframe overlapping with the aggressor ABS Note 2: This noise is applied in OFDM symbols #0, #4, #7, #11 of a subframe overlapping with the aggressor ABS Note 3: This noise is applied in OFDM symbols of a subframe overlapping with aggressor non-ABS Note 4: ABS pattern as defined in [9]. PHICH is transmitted in the serving cell subframe when the subframe is overlapped with the ABS subframe of aggressor cell but not in the 26th subframe indicated by the ABS pattern. Note 5: Time-domain measurement resource restriction pattern for PCell measurements as defined in [7] Note 6: As configured according to the time-domain measurement resource restriction pattern for CSI measurements defined in [7] Note 7: The number of control OFDM symbols is not available for ABS and is 2 for the subframe indicated by “0” of ABS pattern. Note 8: The number of the CRS ports in Cell 1, Cell 2 and Cell 3 is the same. Note 9: SIB-1 will not be transmitted in Cell 2 and Cell 3 in the test. |
||||||
Table 8.5.1.2.3_E.1.5-2: Test requirement FDD PHICH Transmit Diversity 2×2 for feICIC (non-MBSFN ABS)
|
Test Number |
Reference Channel |
OCNG Pattern |
Propagation Conditions (Note 1) |
Antenna Configuration and Correlation Matrix (Note 2) |
Reference Value |
|||||
|
Cell 1 |
Cell 2 |
Cell 3 |
Cell 1 |
Cell 2 |
Cell 3 |
Pm-an (%) |
SNR (dB) (Note 3) |
|||
|
1 |
R.19 |
OP.1 FDD |
OP.1 FDD |
OP.1 FDD |
EPA5 |
EVA5 |
EVA5 |
2×2 Low |
0.1 |
5.9 |
|
Note 1: The propagation conditions for Cell 1, Cell 2 and Cell 3 are statistically independent. Note 2: The correlation matrix and antenna configuration apply for Cell 1, Cell 2 and Cell 3. Note 3: SNR corresponds to of Cell 1.
|
||||||||||
8.5.1.2.4
8.5.1.2.5 FDD Enhanced Downlink Control Channel Performance Requirement Type A for PHICH- 2 Tx Antenna Ports under Asynchronous Network
8.5.1.2.5.1 Test purpose
This test verifies the Enhanced downlink control channel performance requirement Type A for PHICH for 2 transmit diversity under Asynchronous network with a given SNR for which the average probability of miss detection of Hybrid Indicator ("ACK to NACK") of the specified reference measurement channels remains below a specified value.
8.5.1.2.5.2 Test applicability
This test applies to all types of E-UTRA FDD UE Release 13 and forward supporting Enhanced Downlink Control Channel Performance Requirement Type A. Detailed Test Applicability is specified in clause 8.1.2.7.
8.5.1.2.5.3 Minimum conformance requirements
The receiver characteristics of the PHICH are determined by the probability of miss-detecting an ACK for a NACK (Pm-an). It is assumed that there is no bias applied to the detection of ACK and NACK (zero-threshold detection). The parameters specified in Table 8.5.1.2.5.3-1 and Table 8.5.1.2.5.3-2.
The purpose of this test is to verify the PHICH performance with 2 transmit antennas when the serving cell PHICH transmission is interfered by two interfering cells and applying interference model defined in clause B.5.2. In Table 8.5.1.2.5.3-2, Cell 1 is the serving cell, and Cell 2 and Cell 3 are the aggressor cells. The downlink physical channel setup is according to Annex C.3.2 for each of Cell 1, Cell 2 and Cell 3, respectively. The CRS assistance information [7] is not provided.
Table 8.5.1.2.5.3-1: Test Parameters for PHICH
|
Parameter |
Unit |
Transmit diversity |
|
|
Downlink power allocation |
PDCCH_RA PHICH_RA OCNG_RA |
dB |
-3 |
|
PCFICH_RB PDCCH_RB PHICH_RB OCNG_RB |
dB |
-3 |
|
|
PHICH duration |
Normal |
||
|
Number of PHICH groups (Note 1) |
Ng = 1 |
||
|
PDCCH Content |
UL Grant should be included with the proper information aligned with A.3.6. |
||
|
Unused RE-s and PRB-s |
OCNG |
||
|
Cell ID |
0 |
||
|
|
dBm/15kHz |
-98 |
|
|
Cyclic prefix |
Normal |
||
|
Note 1: according to Clause 6.9 in TS 36.211 [8] Note 2: PHICH power settings refer to PHICH group power, i.e. the total power of all active PHICH sequences within a PHICH group. |
|||
at antenna portTable 8.5.1.2.5.3-2: Additional Test Parameters for PHICH
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
||
|
Downlink power allocation |
PDCCH_RA PHICH_RA PDSCH_RA OCNG_RA |
dB |
-3 |
-3 |
-3 |
|
|
PCFICH_RB PHICH_RB PDCCH_RB PDSCH_RB OCNG_RB |
dB |
-3 |
-3 |
-3 |
||
|
Cell-specific reference signals |
Antenna ports 0,1 |
Antenna ports 0,1 |
Antenna ports 0,1 |
|||
|
at antenna port
|
dBm/15kHz |
-98 |
||||
|
|
dB |
N/A |
13.91 |
3.34 |
||
|
BWChannel |
MHz |
10 |
10 |
10 |
||
|
Cyclic Prefix |
Normal |
Normal |
Normal |
|||
|
Cell ID |
0 |
1 |
6 |
|||
|
Subframe Configuration |
Non-MBSFN |
Non-MBSFN |
Non-MBSFN |
|||
|
Number of control OFDM symbols |
1 |
1 |
1 |
|||
|
PHICH Ng (Note 1) |
1 |
N/A |
N/A |
|||
|
PHICH duration |
Normal |
N/A |
N/A |
|||
|
Interference model |
N/A |
As specified in clause B.5.2 |
As specified in clause B.5.2 |
|||
|
Probability of occurrence of PDSCH transmission rank in interfering cells |
Rank 1 |
% |
N/A |
80 |
80 |
|
|
Rank 2 |
% |
N/A |
20 |
20 |
||
|
Unused RE-s and PRB-s |
OCNG |
OCNG |
OCNG |
|||
|
Time offset relative to Cell 1 |
ms |
N/A |
0.33 |
0.67 |
||
|
Frequency offset relative to Cell 1 |
Hz |
N/A |
0 |
0 |
||
|
Note 1: According to Clause 6.9 in TS 36.211 [4]. |
||||||
For the parameters specified in Table 8.5.1.2.5.3-1 and Table 8.5.1.2.5.3-2, the average probability of a miss-detecting an ACK for a NACK (Pm-an) shall be below the specified value in Table 8.5.1.2.5.3-3
Table 8.5.1.2.5.3-3: Minimum performance PHICH for Enhanced Downlink Control Channel Performance Requirement Type A
|
Test Number |
Reference Channel |
OCNG Pattern |
Propagation Conditions (Note 1) |
Antenna Configuration and Correlation Matrix (Note 2) |
Reference Value |
|||||
|
Cell 1 |
Cell 2 |
Cell 3 |
Cell 1 |
Cell 2 |
Cell 3 |
Pm-an (%) |
SNR (dB) (Note 3) |
|||
|
1 |
R.19 |
OP.1 FDD |
OP.1 FDD |
OP.1 FDD |
EVA70 |
EVA70 |
EVA70 |
2×2 Low |
0.1 |
17.9 |
|
Note 1: The propagation conditions for Cell 1, Cell 2 and Cell 3 are statistically independent. Note 2: The correlation matrix and antenna configuration apply for Cell 1, Cell 2 and Cell 3. Note 3: SNR corresponds to of Cell 1 as defined in clause 8.1.1.
|
||||||||||
The normative reference for this requirement is TS 36.101 [2] clause 8.5.1.2.5.
8.5.1.2.5.4 Test description
8.5.1.2.5.4.1 Initial conditions
Test Environment: Normal as defined in TS 36.508 [7] clause 4.1.
Frequencies to be tested: Mid Range as defined in TS 36.508 [7] clause 4.3.1.1.
Channel Bandwidths to be tested: As specified per test number in Table 8.5.1.2.5.3-2 as defined in TS 36.508 [7] clause 4.3.1.1
1. Connect the SS, the faders and AWGN noise sources to the UE antenna connector (s) as shown in TS 36.508 [7] Annex A, Figure A.48 for antenna configuration 2×2.
2. The parameter settings for the cell are set up according to Table 8.5.1.2.5.3-1.
3. Downlink signals are initially set up according to Annex C.1 and C.3.2 and uplink signals according to Annex H.1 and H.3.2.
4. Propagation conditions are set according to Annex B clauses B.0.
5. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 8.5.1.2.5.4.3.
8.5.1.2.5.4.2 Test procedure
1. Set the parameters of bandwidth, reference Channel, the propagation condition, antenna configuration, the correlation matrix and the SNR according to Table 8.5.1.2.5.5-1.
2. SS shall schedule PUSCH transmissions according to Annex A.2.2.1.1 Table A.2.2.1.1-1 to happen during 8 consecutive uplink TTIs via PDCCH DCI format 0 with new data indicator set to true. Since the UE has no payload, the UE shall send uplink MAC padding bits in PUSCH. SS upon receiving the PUSCH transmissions will transmit the associated ACKs. PHICH is set according to Annex 3.6 Table A.3.6-1. SS will only transmit PDCCH to schedule PUSCH transmission in the appropriate sub-frames. Table 8.5.1.2.5.4.2-1 indicates the transmissions for one cycle.
Table 8.5.1.2.5.4.2-1: PHICH test pattern
|
TTI |
1-4 |
5-8 |
9-12 |
13-16 |
17-20 |
21-24 |
|
PDCCH |
S |
S |
– |
– |
S |
S |
|
PHICH |
– |
– |
A |
A |
– |
– |
|
PUSCH |
T |
T |
R |
R |
T |
|
|
UL HARQ Process |
1-4 |
5-8 |
1-4 |
5-8 |
1-4 |
5-8 |
|
Note 1: This table gives an example test pattern for HARQ process for FDD PHICH test Note 2: Following notation is used: |
||||||
3. SS will only monitor for uplink retransmissions due to ACK missed-detections. Such re-transmissions (if they occur) will potentially happen in TTI 13 to 20. DTXs on TTI 13 to 20 are counted as successful ACK receptions while any transmission on these TTIs is counted as NACKs.
4. Repeat steps 1 – 3 for a duration sufficient to achieve statistical significance according to Annex G clause G.4 and measure Pm-an. Pm-an is (NACK) / (ACK + NACK).
If Pm-an is less than the value specified in table 8.5.1.2.5.5-1, pass the UE. Otherwise fail the UE.
8.5.1.2.5.4.3 Message contents
Message contents are according to TS 36.508 [7] clause 4.6 with the following exceptions:
Table 8.5.1.2.5.4.3-1: MAC-MainConfig-RBC
|
Derivation Path: TS 36.508 [7] clause 4.8.2.1.5, Table 4.8.2.1.5-1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
MAC-MainConfig-RBC ::= SEQUENCE { |
||||
|
dl-SCH-Config SEQUENCE {} |
Not present |
|||
|
ul-SCH-Config SEQUENCE { |
||||
|
maxHARQ-Tx |
n2 |
Only one retransmission per UL HARQ |
||
8.5.1.2.5.5 Test requirement
For the parameters specified in Table 8.5.1.2.5.3-1 and Table 8.5.1.2.5.5-1, the average probability of a miss-detecting ACK for NACK (Pm-dsg) shall be below the specified value in Table 8.5.1.2.5.5-2.
Table 8.5.1.2.5.5-1: Additional Test Requirements for PHICH
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
||
|
Downlink power allocation |
PDCCH_RA PHICH_RA PDSCH_RA OCNG_RA |
dB |
-3 |
-3 |
-3 |
|
|
PCFICH_RB PHICH_RB PDCCH_RB PDSCH_RB OCNG_RB |
dB |
-3 |
-3 |
-3 |
||
|
Cell-specific reference signals |
Antenna ports 0,1 |
Antenna ports 0,1 |
Antenna ports 0,1 |
|||
|
at antenna port
|
dBm/15kHz |
-98 |
||||
|
|
dB |
N/A |
14.71 |
4.14 |
||
|
BWChannel |
MHz |
10 |
10 |
10 |
||
|
Cyclic Prefix |
Normal |
Normal |
Normal |
|||
|
Cell ID |
0 |
1 |
6 |
|||
|
Subframe Configuration |
Non-MBSFN |
Non-MBSFN |
Non-MBSFN |
|||
|
Number of control OFDM symbols |
1 |
1 |
1 |
|||
|
PHICH Ng (Note 1) |
1 |
N/A |
N/A |
|||
|
PHICH duration |
Normal |
N/A |
N/A |
|||
|
Interference model |
N/A |
As specified in clause B.5.2 |
As specified in clause B.5.2 |
|||
|
Probability of occurrence of PDSCH transmission rank in interfering cells |
Rank 1 |
% |
N/A |
80 |
80 |
|
|
Rank 2 |
% |
N/A |
20 |
20 |
||
|
Unused RE-s and PRB-s |
OCNG |
OCNG |
OCNG |
|||
|
Time offset relative to Cell 1 |
ms |
N/A |
0.33 |
0.67 |
||
|
Frequency offset relative to Cell 1 |
Hz |
N/A |
0 |
0 |
||
|
Note 1: According to Clause 6.9 in TS 36.211 [8]. |
||||||
Table 8.5.1.2.5.5-2: Test requirement PHICH 2 Tx Antenna Port
|
Test Number |
Reference Channel |
OCNG Pattern |
Propagation Conditions (Note 1) |
Antenna Configuration and Correlation Matrix (Note 2) |
Reference Value |
|||||
|
Cell 1 |
Cell 2 |
Cell 3 |
Cell 1 |
Cell 2 |
Cell 3 |
Pm-an (%) |
SNR (dB) (Note 3) |
|||
|
1 |
R.19 |
OP.1 FDD |
OP.1 FDD |
OP.1 FDD |
EVA70 |
EVA70 |
EVA70 |
2×2 Low |
0.1 |
19.75 |
|
Note 1: The propagation conditions for Cell 1, Cell 2 and Cell 3 are statistically independent. Note 2: The correlation matrix and antenna configuration apply for Cell 1, Cell 2 and Cell 3. Note 3: SNR corresponds to of Cell 1 as defined in clause 8.1.1.
|
||||||||||
8.5.1.2.6 FDD Enhanced Downlink Control Channel Performance Requirement Type A for PHICH – 2 Tx Antenna Ports with Non-Colliding CRS Dominant Interferer
8.5.1.2.6.1 Test purpose
This test verifies the Enhanced downlink control channel performance requirement Type A for PHICH for 2 transmit diversity with Non-Colliding CRS Dominant Interferer with a given SNR for which the average probability of miss detection of Hybrid Indicator ("ACK to NACK") of the specified reference measurement channels remains below a specified value.
8.5.1.2.6.2 Test applicability
This test applies to all types of E-UTRA FDD UE Release 13 and forward supporting Enhanced Downlink Control Channel Performance Requirement Type A. Detailed Test Applicability is specified in clause 8.1.2.7.
8.5.1.2.6.3 Minimum conformance requirements
The receiver characteristics of the PHICH are determined by the probability of miss-detecting an ACK for a NACK (Pm-an). It is assumed that there is no bias applied to the detection of ACK and NACK (zero-threshold detection). The parameters specified in Table 8.5.1.2.6.3-1 and Table 8.5.1.2.6.3-2.
The purpose of this test is to verify the PHICH performance with 2 transmit antennas when the serving cell PHICH transmission is interfered by two interfering cells with the dominant interferer having the non-colliding CRS pattern and applying interference model defined in clause B.7.1. In Table 8.5.1.2.6.3-2, Cell 1 is the serving cell, and Cell 2 and Cell 3 are the aggressor cells. The downlink physical channel setup is according to Annex C.3.2 for each of Cell 1, Cell 2 and Cell 3, respectively. The CRS assistance information [7] is provided and includes Cell 2 and Cell 3.
Table 8.5.1.2.6.3-1: Test Parameters for PHICH
|
Parameter |
Unit |
Single antenna port |
Transmit diversity |
|
|
Downlink power allocation |
PDCCH_RA PHICH_RA OCNG_RA |
dB |
0 |
-3 |
|
PCFICH_RB PDCCH_RB PHICH_RB OCNG_RB |
dB |
0 |
-3 |
|
|
PHICH duration |
Normal |
Normal |
||
|
PHICH Ng (Note 1) |
Ng = 1 |
Ng = 1 |
||
|
PDCCH Content |
UL Grant should be included with the proper information aligned with A.3.6. |
|||
|
Unused RE-s and PRB-s |
OCNG |
OCNG |
||
|
Cell ID |
0 |
0 |
||
|
|
dBm/15kHz |
-98 |
-98 |
|
|
Cyclic prefix |
Normal |
Normal |
||
|
Note 1: according to Clause 6.9 in TS 36.211 [8] |
||||
at antenna portTable 8.5.1.2.6.3-2: Additional Test Parameters for PHICH
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
|
|
Downlink power allocation |
PDCCH_RA OCNG_RA |
dB |
-3 |
-3 |
-3 |
|
PHICH_RA |
dB |
-3 |
N/A |
N/A |
|
|
PCFICH_RB PDCCH_RB OCNG_RB |
dB |
-3 |
-3 |
-3 |
|
|
PHICH_RB |
dB |
-3 |
N/A |
N/A |
|
|
Cell-specific reference signals |
Antenna ports 0,1 |
Antenna ports 0,1 |
Antenna ports 0,1 |
||
|
at antenna port
|
dBm/15kHz |
-98 |
|||
|
|
dB |
N/A |
13.91 |
3.34 |
|
|
BWChannel |
MHz |
10 |
10 |
10 |
|
|
Cyclic Prefix |
Normal |
Normal |
Normal |
||
|
Cell ID |
0 |
1 |
6 |
||
|
Subframe Configuration |
Non-MBSFN |
Non-MBSFN |
Non-MBSFN |
||
|
Number of control OFDM symbols |
1 |
1 |
1 |
||
|
PHICH Ng (Note 1) |
1 |
N/A |
N/A |
||
|
PHICH duration |
Normal |
N/A |
N/A |
||
|
Interference model |
N/A |
As specified in clause B.7.1 |
As specified in clause B.7.1 |
||
|
Unused RE-s and PRB-s (Note 2) |
OCNG |
OCNG |
OCNG |
||
|
Time offset to cell 1 |
us |
N/A |
2 |
3 |
|
|
Frequency offset to cell 1 |
Hz |
N/A |
200 |
300 |
|
|
Note 1: According to Clause 6.9 in TS 36.211 [8]. Note 2: For Cell 2 and Cell 3 unused RE-s and PRB-s do not include control region REs. |
|||||
For the parameters specified in Table 8.5.1.2.6.3-1 and Table 8.5.1.2.6.3-2, the average probability of a miss-detecting an ACK for a NACK (Pm-an) shall be below the specified value in Table 8.5.1.2.6.3-3.
Table 8.5.1.2.6.3-3: Minimum performance PHICH for Enhanced Downlink Control Channel Performance Requirement Type A
|
Test Number |
Reference Channel |
OCNG Pattern |
Propagation Conditions (Note 1) |
Antenna Configuration and Correlation Matrix (Note 2) |
Reference Value |
|||||
|
Cell 1 |
Cell 2 |
Cell 3 |
Cell 1 |
Cell 2 |
Cell 3 |
Pm-an (%) |
SNR (dB) (Note 3) |
|||
|
1 |
R.19 |
OP.1 FDD |
OP.1 FDD |
OP.1 FDD |
EPA5 |
EPA5 |
EPA5 |
2×2 Low |
0.1 |
15.8 |
|
Note 1: The propagation conditions for Cell 1, Cell 2 and Cell 3 are statistically independent. Note 2: The correlation matrix and antenna configuration apply for Cell 1, Cell 2 and Cell 3. Note 3: SNR corresponds to of Cell 1 as defined in clause 8.1.1.
|
||||||||||
The normative reference for this requirement is TS 36.101 [2] clause 8.5.1.2.6.5.
8.5.1.2.6.4 Test description
8.5.1.2.6.4.1 Initial conditions
Test Environment: Normal as defined in TS 36.508 [7] clause 4.1.
Frequencies to be tested: Mid Range as defined in TS 36.508 [7] clause 4.3.1.1.
Channel Bandwidths to be tested: As specified per test number in Table 8.5.1.2.6.3-2 as defined in TS 36.508 [7] clause 4.3.1.1
1. Connect the SS, the faders and AWGN noise sources to the UE antenna connector (s) as shown in TS 36.508 [7] Annex A, Figure A.48 for antenna configuration 2×2.
2. The parameter settings for the cell are set up according to Table 8.5.1.2.6.3-1.
3. Downlink signals are initially set up according to Annex C.1 and C.3.2 and uplink signals according to Annex H.1 and H.3.2.
4. Propagation conditions are set according to Annex B clauses B.0.
5. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 8.5.1.2.6.4.3.
8.5.1.2.6.4.2 Test procedure
1. Set the parameters of bandwidth, reference Channel, the propagation condition, antenna configuration, the correlation matrix and the SNR according to Table 8.5.1.2.6.5-1.
2. SS shall schedule PUSCH transmissions according to Annex A.2.2.1.1 Table A.2.2.1.1-1 to happen during 8 consecutive uplink TTIs via PDCCH DCI format 0 with new data indicator set to true. Since the UE has no payload, the UE shall send uplink MAC padding bits in PUSCH. SS upon receiving the PUSCH transmissions will transmit the associated ACKs. PHICH is set according to Annex 3.6 Table A.3.6-1. SS will only transmit PDCCH to schedule PUSCH transmission in the appropriate sub-frames. Table 8.5.1.2.6.4.2-1 indicates the transmissions for one cycle.
Table 8.5.1.2.6.4.2-1: PHICH test pattern
|
TTI |
1-4 |
5-8 |
9-12 |
13-16 |
17-20 |
21-24 |
|
PDCCH |
S |
S |
– |
– |
S |
S |
|
PHICH |
– |
– |
A |
A |
– |
– |
|
PUSCH |
T |
T |
R |
R |
T |
|
|
UL HARQ Process |
1-4 |
5-8 |
1-4 |
5-8 |
1-4 |
5-8 |
|
Note 1: This table gives an example test pattern for HARQ process for FDD PHICH test Note 2: Following notation is used: |
||||||
3. SS will only monitor for uplink retransmissions due to ACK missed-detections. Such re-transmissions (if they occur) will potentially happen in TTI 13 to 20. DTXs on TTI 13 to 20 are counted as successful ACK receptions while any transmission on these TTIs is counted as NACKs.
4. Repeat steps 1 – 3 for a duration sufficient to achieve statistical significance according to Annex G clause G.4 and measure Pm-an. Pm-an is (NACK) / (ACK + NACK).
If Pm-an is less than the value specified in table 8.5.1.2.6.5-1, pass the UE. Otherwise fail the UE.
8.5.1.2.6.4.3 Message contents
Message contents are according to TS 36.508 [7] clause 5.2A.8.1 with the following exceptions:
Table 8.5.1.2.6.4.3-1: MAC-MainConfig-RBC
|
Derivation Path: TS 36.508 [7] clause 4.8.2.1.5, Table 4.8.2.1.5-1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
MAC-MainConfig-RBC ::= SEQUENCE { |
||||
|
dl-SCH-Config SEQUENCE {} |
Not present |
|||
|
ul-SCH-Config SEQUENCE { |
||||
|
maxHARQ-Tx |
n2 |
Only one retransmission per UL HARQ |
||
8.5.1.2.6.5 Test requirement
For the parameters specified in Table 8.5.1.2.6.3-1 and Table 8.5.1.2.6.5-1, the average probability of a miss-detecting ACK for NACK (Pm-dsg) shall be below the specified value in Table 8.5.1.2.6.5-2.
Table 8.5.1.2.6.5-1: Additional Test Requirements for PHICH
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
|
|
Downlink power allocation |
PDCCH_RA OCNG_RA |
dB |
-3 |
-3 |
-3 |
|
PHICH_RA |
dB |
-3 |
N/A |
N/A |
|
|
PCFICH_RB PDCCH_RB OCNG_RB |
dB |
-3 |
-3 |
-3 |
|
|
PHICH_RB |
dB |
-3 |
N/A |
N/A |
|
|
Cell-specific reference signals |
Antenna ports 0,1 |
Antenna ports 0,1 |
Antenna ports 0,1 |
||
|
at antenna port
|
dBm/15kHz |
-98 |
|||
|
|
dB |
N/A |
14.71 |
4.14 |
|
|
BWChannel |
MHz |
10 |
10 |
10 |
|
|
Cyclic Prefix |
Normal |
Normal |
Normal |
||
|
Cell ID |
0 |
1 |
6 |
||
|
Subframe Configuration |
Non-MBSFN |
Non-MBSFN |
Non-MBSFN |
||
|
Number of control OFDM symbols |
1 |
1 |
1 |
||
|
PHICH Ng (Note 1) |
1 |
N/A |
N/A |
||
|
PHICH duration |
Normal |
N/A |
N/A |
||
|
Interference model |
N/A |
As specified in clause B.7.1 |
As specified in clause B.7.1 |
||
|
Unused RE-s and PRB-s (Note 2) |
OCNG |
OCNG |
OCNG |
||
|
Time offset to cell 1 |
us |
N/A |
2 |
3 |
|
|
Frequency offset to cell 1 |
Hz |
N/A |
200 |
300 |
|
|
Note 1: According to Clause 6.9 in TS 36.211 [8]. Note 2: For Cell 2 and Cell 3 unused RE-s and PRB-s do not include control region REs. |
|||||
Table 8.5.1.2.6.5-2: Test requirement PHICH 2 Tx Antenna Port
|
Test Number |
Reference Channel |
OCNG Pattern |
Propagation Conditions (Note 1) |
Antenna Configuration and Correlation Matrix (Note 2) |
Reference Value |
|||||
|
Cell 1 |
Cell 2 |
Cell 3 |
Cell 1 |
Cell 2 |
Cell 3 |
Pm-an (%) |
SNR (dB) (Note 3) |
|||
|
1 |
R.19 |
OP.1 FDD |
OP.1 FDD |
OP.1 FDD |
EPA5 |
EPA5 |
EPA5 |
2×2 Low |
0.1 |
17.65 |
|
Note 1: The propagation conditions for Cell 1, Cell 2 and Cell 3 are statistically independent. Note 2: The correlation matrix and antenna configuration apply for Cell 1, Cell 2 and Cell 3. Note 3: SNR corresponds to of Cell 1 as defined in clause 8.1.1.
|
||||||||||
8.5.1.2.7 FDD Enhanced Downlink Control Channel Performance Requirement Type B for PHICH – 2 Tx Antenna Ports with Colliding CRS Dominant Interferer
8.5.1.2.7.1 Test purpose
This test verifies the Enhanced downlink control channel performance requirement Type B for PHICH for 2 transmit diversity with Colliding CRS Dominant Interferer with a given SNR for which the average probability of miss detection of Hybrid Indicator ("ACK to NACK") of the specified reference measurement channels remains below a specified value.
8.5.1.2.7.2 Test applicability
This test applies to all types of E-UTRA FDD UE Release 13 and forward supporting Enhanced Downlink Control Channel Performance Requirement Type B. Detailed Test Applicability is specified in clause 8.1.2.7.
8.5.1.2.7.3 Minimum conformance requirements
The receiver characteristics of the PHICH are determined by the probability of miss-detecting an ACK for a NACK (Pm-an). It is assumed that there is no bias applied to the detection of ACK and NACK (zero-threshold detection). The parameters specified in Table 8.5.1.2.7.3-1 and Table 8.5.1.2.7.3-2.
The purpose of this test is to verify the PHICH performance with 2 transmit antennas when the serving cell PHICH transmission is interfered by two interfering cells with the dominant interferer having the colliding CRS pattern and applying interference model defined in clause B.7.1. In Table 8.5.1.2.7.3-2, Cell 1 is the serving cell, and Cell 2 and Cell 3 are the aggressor cells. The downlink physical channel setup is according to Annex C.3.2 for each of Cell 1, Cell 2 and Cell 3, respectively. The CRS assistance information [7] is provided and includes Cell 2 and Cell 3.
Table 8.5.1.2.7.3-1: Test Parameters for PHICH
|
Parameter |
Unit |
Single antenna port |
Transmit diversity |
|
|
Downlink power allocation |
PDCCH_RA PHICH_RA OCNG_RA |
dB |
0 |
-3 |
|
PCFICH_RB PDCCH_RB PHICH_RB OCNG_RB |
dB |
0 |
-3 |
|
|
PHICH duration |
Normal |
Normal |
||
|
PHICH Ng (Note 1) |
Ng = 1 |
Ng = 1 |
||
|
PDCCH Content |
UL Grant should be included with the proper information aligned with A.3.6. |
|||
|
Unused RE-s and PRB-s |
OCNG |
OCNG |
||
|
Cell ID |
0 |
0 |
||
|
|
dBm/15kHz |
-98 |
-98 |
|
|
Cyclic prefix |
Normal |
Normal |
||
|
Note 1: according to Clause 6.9 in TS 36.211 [8] |
||||
at antenna portTable 8.5.1.2.7.3-2: Additional Test Parameters for PHICH
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
|
|
Downlink power allocation |
PDCCH_RA OCNG_RA |
dB |
-3 |
-3 |
-3 |
|
PHICH_RA |
dB |
-3 |
N/A |
N/A |
|
|
PCFICH_RB PDCCH_RB OCNG_RB |
dB |
-3 |
-3 |
-3 |
|
|
PHICH_RB |
dB |
-3 |
N/A |
N/A |
|
|
Cell-specific reference signals |
Antenna ports 0,1 |
Antenna ports 0,1 |
Antenna ports 0,1 |
||
|
at antenna port
|
dBm/15kHz |
-98 |
|||
|
|
dB |
N/A |
13.91 |
3.34 |
|
|
BWChannel |
MHz |
10 |
10 |
10 |
|
|
Cyclic Prefix |
Normal |
Normal |
Normal |
||
|
Cell ID |
0 |
6 |
1 |
||
|
Subframe Configuration |
Non-MBSFN |
Non-MBSFN |
Non-MBSFN |
||
|
Number of control OFDM symbols |
1 |
1 |
1 |
||
|
PHICH Ng (Note 1) |
1 |
N/A |
N/A |
||
|
PHICH duration |
Normal |
N/A |
N/A |
||
|
Interference model |
N/A |
As specified in clause B.7.1 |
As specified in clause B.7.1 |
||
|
Unused RE-s and PRB-s (Note 2) |
OCNG |
OCNG |
OCNG |
||
|
Time offset to cell 1 |
us |
N/A |
2 |
3 |
|
|
Frequency offset to cell 1 |
Hz |
N/A |
200 |
300 |
|
|
Note 1: According to Clause 6.9 in TS 36.211 [8]. Note 2: For Cell 2 and Cell 3 unused RE-s and PRB-s do not include control region REs. |
|||||
For the parameters specified in Table 8.5.1.2.7.3-1 and Table 8.5.1.2.7.3-2, the average probability of a miss-detecting an ACK for a NACK (Pm-an) shall be below the specified value in Table 8.5.1.2.7.3-3.
Table 8.5.1.2.7.3-3: Minimum performance PHICH for Enhanced Downlink Control Channel Performance Requirement Type B
|
Test Number |
Reference Channel |
OCNG Pattern |
Propagation Conditions (Note 1) |
Antenna Configuration and Correlation Matrix (Note 2) |
Reference Value |
|||||
|
Cell 1 |
Cell 2 |
Cell 3 |
Cell 1 |
Cell 2 |
Cell 3 |
Pm-an (%) |
SNR (dB) (Note 3) |
|||
|
1 |
R.19 |
OP.1 FDD |
OP.1 FDD |
OP.1 FDD |
EPA5 |
EPA5 |
EPA5 |
2×2 Low |
0.1 |
13.4 |
|
Note 1: The propagation conditions for Cell 1, Cell 2 and Cell 3 are statistically independent. Note 2: The correlation matrix and antenna configuration apply for Cell 1, Cell 2 and Cell 3. Note 3: SNR corresponds to of Cell 1 as defined in clause 8.1.1.
|
||||||||||
The normative reference for this requirement is TS 36.101 [2] clause 8.5.1.2.7.5.
8.5.1.2.7.4 Test description
8.5.1.2.7.4.1 Initial conditions
Test Environment: Normal as defined in TS 36.508 [7] clause 4.1.
Frequencies to be tested: Mid Range as defined in TS 36.508 [7] clause 4.3.1.1.
Channel Bandwidths to be tested: As specified per test number in Table 8.5.1.2.7.3-2 as defined in TS 36.508 [7] clause 4.3.1.1
1. Connect the SS, the faders and AWGN noise sources to the UE antenna connector (s) as shown in TS 36.508 [7] Annex A, Figure A.48 for antenna configuration 2×2.
2. The parameter settings for the cell are set up according to Table 8.5.1.2.7.3-1.
3. Downlink signals are initially set up according to Annex C.1 and C.3.2 and uplink signals according to Annex H.1 and H.3.2.
4. Propagation conditions are set according to Annex B clauses B.0.
5. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 8.5.1.2.7.4.3.
8.5.1.2.7.4.2 Test procedure
1. Set the parameters of bandwidth, reference Channel, the propagation condition, antenna configuration, the correlation matrix and the SNR according to Table 8.5.1.2.7.5-1.
2. SS shall schedule PUSCH transmissions according to Annex A.2.2.1.1 Table A.2.2.1.1-1 to happen during 8 consecutive uplink TTIs via PDCCH DCI format 0 with new data indicator set to true. Since the UE has no payload, the UE shall send uplink MAC padding bits in PUSCH. SS upon receiving the PUSCH transmissions will transmit the associated ACKs. PHICH is set according to Annex 3.6 Table A.3.6-1. SS will only transmit PDCCH to schedule PUSCH transmission in the appropriate sub-frames. Table 8.5.1.2.7.4.2-1 indicates the transmissions for one cycle.
Table 8.5.1.2.7.4.2-1: PHICH test pattern
|
TTI |
1-4 |
5-8 |
9-12 |
13-16 |
17-20 |
21-24 |
|
PDCCH |
S |
S |
– |
– |
S |
S |
|
PHICH |
– |
– |
A |
A |
– |
– |
|
PUSCH |
T |
T |
R |
R |
T |
|
|
UL HARQ Process |
1-4 |
5-8 |
1-4 |
5-8 |
1-4 |
5-8 |
|
Note 1: This table gives an example test pattern for HARQ process for FDD PHICH test Note 2: Following notation is used: |
||||||
3. SS will only monitor for uplink retransmissions due to ACK missed-detections. Such re-transmissions (if they occur) will potentially happen in TTI 13 to 20. DTXs on TTI 13 to 20 are counted as successful ACK receptions while any transmission on these TTIs is counted as NACKs.
4. Repeat steps 1 – 3 for a duration sufficient to achieve statistical significance according to Annex G clause G.4 and measure Pm-an. Pm-an is (NACK) / (ACK + NACK).
If Pm-an is less than the value specified in table 8.5.1.2.7.5-1, pass the UE. Otherwise fail the UE.
8.5.1.2.7.4.3 Message contents
Message contents are according to TS 36.508 [7] clause 5.2A.8.1 with the following exceptions:
Table 8.5.1.2.7.4.3-1: MAC-MainConfig-RBC
|
Derivation Path: TS 36.508 [7] clause 4.8.2.1.5, Table 4.8.2.1.5-1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
MAC-MainConfig-RBC ::= SEQUENCE { |
||||
|
dl-SCH-Config SEQUENCE {} |
Not present |
|||
|
ul-SCH-Config SEQUENCE { |
||||
|
maxHARQ-Tx |
n2 |
Only one retransmission per UL HARQ |
||
8.5.1.2.7.5 Test requirement
For the parameters specified in Table 8.5.1.2.7.3-1 and Table 8.5.1.2.7.5-1, the average probability of a miss-detecting ACK for NACK (Pm-dsg) shall be below the specified value in Table 8.5.1.2.7.5-2.
Table 8.5.1.2.7.5-1: Additional Test Requirements for PHICH
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
|
|
Downlink power allocation |
PDCCH_RA OCNG_RA |
dB |
-3 |
-3 |
-3 |
|
PHICH_RA |
dB |
-3 |
N/A |
N/A |
|
|
PCFICH_RB PDCCH_RB OCNG_RB |
dB |
-3 |
-3 |
-3 |
|
|
PHICH_RB |
dB |
-3 |
N/A |
N/A |
|
|
Cell-specific reference signals |
Antenna ports 0,1 |
Antenna ports 0,1 |
Antenna ports 0,1 |
||
|
at antenna port
|
dBm/15kHz |
-98 |
|||
|
|
dB |
N/A |
14.71 |
4.14 |
|
|
BWChannel |
MHz |
10 |
10 |
10 |
|
|
Cyclic Prefix |
Normal |
Normal |
Normal |
||
|
Cell ID |
0 |
6 |
1 |
||
|
Subframe Configuration |
Non-MBSFN |
Non-MBSFN |
Non-MBSFN |
||
|
Number of control OFDM symbols |
1 |
1 |
1 |
||
|
PHICH Ng (Note 1) |
1 |
N/A |
N/A |
||
|
PHICH duration |
Normal |
N/A |
N/A |
||
|
Interference model |
N/A |
As specified in clause B.7.1 |
As specified in clause B.7.1 |
||
|
Unused RE-s and PRB-s (Note 2) |
OCNG |
OCNG |
OCNG |
||
|
Time offset to cell 1 |
us |
N/A |
2 |
3 |
|
|
Frequency offset to cell 1 |
Hz |
N/A |
200 |
300 |
|
|
Note 1: According to Clause 6.9 in TS 36.211 [8]. Note 2: For Cell 2 and Cell 3 unused RE-s and PRB-s do not include control region REs. |
|||||
Table 8.5.1.2.7.5-2: Test requirement PHICH 2 Tx Antenna Port
|
Test Number |
Reference Channel |
OCNG Pattern |
Propagation Conditions (Note 1) |
Antenna Configuration and Correlation Matrix (Note 2) |
Reference Value |
|||||
|
Cell 1 |
Cell 2 |
Cell 3 |
Cell 1 |
Cell 2 |
Cell 3 |
Pm-an (%) |
SNR (dB) (Note 3) |
|||
|
1 |
R.19 |
OP.1 FDD |
OP.1 FDD |
OP.1 FDD |
EPA5 |
EPA5 |
EPA5 |
2×2 Low |
0.1 |
15.25 |
|
Note 1: The propagation conditions for Cell 1, Cell 2 and Cell 3 are statistically independent. Note 2: The correlation matrix and antenna configuration apply for Cell 1, Cell 2 and Cell 3. Note 3: SNR corresponds to of Cell 1 as defined in clause 8.1.1.
|
||||||||||
8.5.1.2.8 FDD Enhanced Downlink Control Channel Performance Requirement Type B for PHICH – 2 Tx Antenna Ports with Non-Colliding CRS Dominant Interferer
8.5.1.2.8.1 Test purpose
This test verifies the Enhanced downlink control channel performance requirement Type B for PHICH for 2 transmit diversity with Non-Colliding CRS Dominant Interferer with a given SNR for which the average probability of miss detection of Hybrid Indicator ("ACK to NACK") of the specified reference measurement channels remains below a specified value.
8.5.1.2.8.2 Test applicability
This test applies to all types of E-UTRA FDD UE Release 13 and forward supporting Enhanced Downlink Control Channel Performance Requirement Type B. Detailed Test Applicability is specified in clause 8.1.2.7.
8.5.1.2.8.3 Minimum conformance requirements
The receiver characteristics of the PHICH are determined by the probability of miss-detecting an ACK for a NACK (Pm-an). It is assumed that there is no bias applied to the detection of ACK and NACK (zero-threshold detection). The parameters specified in Table 8.5.1.2.8.3-1 and Table 8.5.1.2.8.3-2.
The purpose of this test is to verify the PHICH performance with 2 transmit antennas when the serving cell PHICH transmission is interfered by two interfering cells with the dominant interferer having the non-colliding CRS pattern and applying interference model defined in clause B.7.1. In Table 8.5.1.2.8.3-2, Cell 1 is the serving cell, and Cell 2 and Cell 3 are the aggressor cells. The downlink physical channel setup is according to Annex C.3.2 for each of Cell 1, Cell 2 and Cell 3, respectively. The CRS assistance information [7] is provided and includes Cell 2 and Cell 3.
Table 8.5.1.2.8.3-1: Test Parameters for PHICH
|
Parameter |
Unit |
Single antenna port |
Transmit diversity |
|
|
Downlink power allocation |
PDCCH_RA PHICH_RA OCNG_RA |
dB |
0 |
-3 |
|
PCFICH_RB PDCCH_RB PHICH_RB OCNG_RB |
dB |
0 |
-3 |
|
|
PHICH duration |
Normal |
Normal |
||
|
PHICH Ng (Note 1) |
Ng = 1 |
Ng = 1 |
||
|
PDCCH Content |
UL Grant should be included with the proper information aligned with A.3.6. |
|||
|
Unused RE-s and PRB-s |
OCNG |
OCNG |
||
|
Cell ID |
0 |
0 |
||
|
|
dBm/15kHz |
-98 |
-98 |
|
|
Cyclic prefix |
Normal |
Normal |
||
|
Note 1: according to Clause 6.9 in TS 36.211 [8] |
||||
at antenna portTable 8.5.1.2.8.3-2: Additional Test Parameters for PHICH
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
|
|
Downlink power allocation |
PDCCH_RA OCNG_RA |
dB |
-3 |
-3 |
-3 |
|
PHICH_RA |
dB |
-3 |
N/A |
N/A |
|
|
PCFICH_RB PDCCH_RB OCNG_RB |
dB |
-3 |
-3 |
-3 |
|
|
PHICH_RB |
dB |
-3 |
N/A |
N/A |
|
|
Cell-specific reference signals |
Antenna ports 0,1 |
Antenna ports 0,1 |
Antenna ports 0,1 |
||
|
at antenna port
|
dBm/15kHz |
-98 |
|||
|
|
dB |
N/A |
13.91 |
3.34 |
|
|
BWChannel |
MHz |
10 |
10 |
10 |
|
|
Cyclic Prefix |
Normal |
Normal |
Normal |
||
|
Cell ID |
0 |
1 |
6 |
||
|
Subframe Configuration |
Non-MBSFN |
Non-MBSFN |
Non-MBSFN |
||
|
Number of control OFDM symbols |
1 |
1 |
1 |
||
|
PHICH Ng (Note 1) |
1 |
N/A |
N/A |
||
|
PHICH duration |
Normal |
N/A |
N/A |
||
|
Interference model |
N/A |
As specified in clause B.7.1 |
As specified in clause B.7.1 |
||
|
Unused RE-s and PRB-s (Note 2) |
OCNG |
OCNG |
OCNG |
||
|
Time offset to cell 1 |
us |
N/A |
2 |
3 |
|
|
Frequency offset to cell 1 |
Hz |
N/A |
200 |
300 |
|
|
Note 1: According to Clause 6.9 in TS 36.211 [8]. Note 2: For Cell 2 and Cell 3 unused RE-s and PRB-s do not include control region REs. |
|||||
For the parameters specified in Table 8.5.1.2.8.3-1 and Table 8.5.1.2.8.3-2, the average probability of a miss-detecting an ACK for a NACK (Pm-an) shall be below the specified value in Table 8.5.1.2.8.3-3.
Table 8.5.1.2.8.3-3: Minimum performance PHICH for Enhanced Downlink Control Channel Performance Requirement Type B
|
Test Number |
Reference Channel |
OCNG Pattern |
Propagation Conditions (Note 1) |
Antenna Configuration and Correlation Matrix (Note 2) |
Reference Value |
|||||
|
Cell 1 |
Cell 2 |
Cell 3 |
Cell 1 |
Cell 2 |
Cell 3 |
Pm-an (%) |
SNR (dB) (Note 3) |
|||
|
1 |
R.19 |
OP.1 FDD |
OP.1 FDD |
OP.1 FDD |
EPA5 |
EPA5 |
EPA5 |
2×2 Low |
0.1 |
15.0 |
|
Note 1: The propagation conditions for Cell 1, Cell 2 and Cell 3 are statistically independent. Note 2: The correlation matrix and antenna configuration apply for Cell 1, Cell 2 and Cell 3. Note 3: SNR corresponds to of Cell 1 as defined in clause 8.1.1.
|
||||||||||
The normative reference for this requirement is TS 36.101 [2] clause 8.5.1.2.8.5.
8.5.1.2.8.4 Test description
8.5.1.2.8.4.1 Initial conditions
Test Environment: Normal as defined in TS 36.508 [7] clause 4.1.
Frequencies to be tested: Mid Range as defined in TS 36.508 [7] clause 4.3.1.1.
Channel Bandwidths to be tested: As specified per test number in Table 8.5.1.2.8.3-2 as defined in TS 36.508 [7] clause 4.3.1.1
1. Connect the SS, the faders and AWGN noise sources to the UE antenna connector (s) as shown in TS 36.508 [7] Annex A, Figure A.48 for antenna configuration 2×2.
2. The parameter settings for the cell are set up according to Table 8.5.1.2.8.3-1.
3. Downlink signals are initially set up according to Annex C.1 and C.3.2 and uplink signals according to Annex H.1 and H.3.2.
4. Propagation conditions are set according to Annex B clauses B.0.
5. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 8.5.1.2.8.4.3.
8.5.1.2.8.4.2 Test procedure
1. Set the parameters of bandwidth, reference Channel, the propagation condition, antenna configuration, the correlation matrix and the SNR according to Table 8.5.1.2.8.5-1.
2. SS shall schedule PUSCH transmissions according to Annex A.2.2.1.1 Table A.2.2.1.1-1 to happen during 8 consecutive uplink TTIs via PDCCH DCI format 0 with new data indicator set to true. Since the UE has no payload, the UE shall send uplink MAC padding bits in PUSCH. SS upon receiving the PUSCH transmissions will transmit the associated ACKs. PHICH is set according to Annex 3.6 Table A.3.6-1. SS will only transmit PDCCH to schedule PUSCH transmission in the appropriate sub-frames. Table 8.5.1.2.8.4.2-1 indicates the transmissions for one cycle.
Table 8.5.1.2.8.4.2-1: PHICH test pattern
|
TTI |
1-4 |
5-8 |
9-12 |
13-16 |
17-20 |
21-24 |
|
PDCCH |
S |
S |
– |
– |
S |
S |
|
PHICH |
– |
– |
A |
A |
– |
– |
|
PUSCH |
T |
T |
R |
R |
T |
|
|
UL HARQ Process |
1-4 |
5-8 |
1-4 |
5-8 |
1-4 |
5-8 |
|
Note 1: This table gives an example test pattern for HARQ process for FDD PHICH test Note 2: Following notation is used: |
||||||
3. SS will only monitor for uplink retransmissions due to ACK missed-detections. Such re-transmissions (if they occur) will potentially happen in TTI 13 to 20. DTXs on TTI 13 to 20 are counted as successful ACK receptions while any transmission on these TTIs is counted as NACKs.
4. Repeat steps 1 – 3 for a duration sufficient to achieve statistical significance according to Annex G clause G.4 and measure Pm-an. Pm-an is (NACK) / (ACK + NACK).
If Pm-an is less than the value specified in table 8.5.1.2.8.5-1, pass the UE. Otherwise fail the UE.
8.5.1.2.8.4.3 Message contents
Message contents are according to TS 36.508 [7] clause 5.2A.8.1 with the following exceptions:
Table 8.5.1.2.8.4.3-1: MAC-MainConfig-RBC
|
Derivation Path: TS 36.508 [7] clause 4.8.2.1.5, Table 4.8.2.1.5-1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
MAC-MainConfig-RBC ::= SEQUENCE { |
||||
|
dl-SCH-Config SEQUENCE {} |
Not present |
|||
|
ul-SCH-Config SEQUENCE { |
||||
|
maxHARQ-Tx |
n2 |
Only one retransmission per UL HARQ |
||
8.5.1.2.8.5 Test requirement
For the parameters specified in Table 8.5.1.2.8.3-1 and Table 8.5.1.2.8.5-1, the average probability of a miss-detecting ACK for NACK (Pm-dsg) shall be below the specified value in Table 8.5.1.2.8.5-2.
Table 8.5.1.2.8.5-1: Additional Test Requirements for PHICH
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
|
|
Downlink power allocation |
PDCCH_RA OCNG_RA |
dB |
-3 |
-3 |
-3 |
|
PHICH_RA |
dB |
-3 |
N/A |
N/A |
|
|
PCFICH_RB PDCCH_RB OCNG_RB |
dB |
-3 |
-3 |
-3 |
|
|
PHICH_RB |
dB |
-3 |
N/A |
N/A |
|
|
Cell-specific reference signals |
Antenna ports 0,1 |
Antenna ports 0,1 |
Antenna ports 0,1 |
||
|
at antenna port
|
dBm/15kHz |
-98 |
|||
|
|
dB |
N/A |
14.71 |
4.14 |
|
|
BWChannel |
MHz |
10 |
10 |
10 |
|
|
Cyclic Prefix |
Normal |
Normal |
Normal |
||
|
Cell ID |
0 |
1 |
6 |
||
|
Subframe Configuration |
Non-MBSFN |
Non-MBSFN |
Non-MBSFN |
||
|
Number of control OFDM symbols |
1 |
1 |
1 |
||
|
PHICH Ng (Note 1) |
1 |
N/A |
N/A |
||
|
PHICH duration |
Normal |
N/A |
N/A |
||
|
Interference model |
N/A |
As specified in clause B.7.1 |
As specified in clause B.7.1 |
||
|
Unused RE-s and PRB-s (Note 2) |
OCNG |
OCNG |
OCNG |
||
|
Time offset to cell 1 |
us |
N/A |
2 |
3 |
|
|
Frequency offset to cell 1 |
Hz |
N/A |
200 |
300 |
|
|
Note 1: According to Clause 6.9 in TS 36.211 [8]. Note 2: For Cell 2 and Cell 3 unused RE-s and PRB-s do not include control region REs. |
|||||
Table 8.5.1.2.8.5-2: Test requirement PHICH 2 Tx Antenna Port
|
Test Number |
Reference Channel |
OCNG Pattern |
Propagation Conditions (Note 1) |
Antenna Configuration and Correlation Matrix (Note 2) |
Reference Value |
|||||
|
Cell 1 |
Cell 2 |
Cell 3 |
Cell 1 |
Cell 2 |
Cell 3 |
Pm-an (%) |
SNR (dB) (Note 3) |
|||
|
1 |
R.19 |
OP.1 FDD |
OP.1 FDD |
OP.1 FDD |
EPA5 |
EPA5 |
EPA5 |
2×2 Low |
0.1 |
16.85 |
|
Note 1: The propagation conditions for Cell 1, Cell 2 and Cell 3 are statistically independent. Note 2: The correlation matrix and antenna configuration apply for Cell 1, Cell 2 and Cell 3. Note 3: SNR corresponds to of Cell 1 as defined in clause 8.1.1.
|
||||||||||
