7.7G Spurious response for V2X Communication
36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification
7.7G.1 Spurious response for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
7.7G.1.1 Test Purpose
Spurious response for V2X verifies the receiver’s ability to receive a wanted aggregated signal on its assigned channel frequency without exceeding a given degradation due to the presence of an unwanted CW interfering signal at any other frequency at which a response is obtained i.e. for which the out of band blocking limit as specified in sub-clause 7.6.2G is not met.
The lack of the spurious response ability decreases the coverage area when other unwanted interfering signal exists at any other frequency.
7.7G.1.2 Test Applicability
This test applies to all types of UE that support V2X Sidelink Communication and Band 47.
7.7G.1.3 Minimum Conformance Requirements
The throughput shall be ≥ 95% of the maximum throughput of the reference measurement channels as specified in Annex A.8.2 with parameters specified in Tables 7.7G.3-1 and 7.7G.3-2.
Table 7.7G.3-1: Spurious response parameters
|
Rx parameter |
Units |
Channel bandwidth |
||||||
|
1.4 MHz |
3 MHz |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
|||
|
Power in Transmission Bandwidth Configuration |
dBm |
PREFSENS_V2X + channel bandwidth specific value below |
||||||
|
6 |
9 |
|||||||
|
NOTE 1: Reference measurement channel is specified in TS36.101[2] Annex A.8.2. |
||||||||
Table 7.7G.3-2: Spurious response
|
Parameter |
Unit |
Level |
|
PInterferer (CW) |
dBm |
-44 |
|
FInterferer |
MHz |
Spurious response frequencies |
The normative reference for this requirement is TS 36.101 [2] clause 7.7.1G.
7.7G.1.4 Test Description
7.7G.1.4.1 Initial Conditions
The initial conditions shall be the same as in clause 7.6.2G.1.4.1 in order to test spurious responses obtained in clause 7.6.2G under the same conditions.
7.7G.1.4.2 Test Procedure
1. The UE starts to perform the V2X sidelink communication according to SL-V2X-Preconfiguration and to schedule the V2X RMC according to Table 7.6.2G.1.4.1-1.
3. Set the parameters of the CW signal generator for an interfering signal according to Table 7.7G.1.5-2. The spurious frequencies are taken from records in the final step of test procedures in clause 7.6.2G.1.4.2.
4. Set the signal level of V2X to the value defined in table 7.7G.1.5-1.
5. For the spurious frequency, measure the average throughput for a duration sufficient to achieve statistical significance according to Annex G.2.
7.7G.1.4.3 Message Contents
Message contents are according to TS 36.508 [7] subclause 4.10.
7.7G.1.5 Test Requirement
The throughput measurement derived in test procedure shall be ≥ 95% of the maximum throughput of the reference measurement channels as specified in Annex A.8.2 with parameters specified in Tables 7.7G.1.5-1 and 7.7G.1.5-2.
Table 7.7G.1.5-1: Spurious response parameters
|
Rx parameter |
Units |
Channel bandwidth |
||||||
|
1.4 MHz |
3 MHz |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
|||
|
Power in Transmission Bandwidth Configuration |
dBm |
PREFSENS_V2X + channel bandwidth specific value below |
||||||
|
6 |
9 |
|||||||
|
NOTE 1: Reference measurement channel is specified in TS36.101[2] Annex A.8.2. |
||||||||
Table 7.7G.1.5-2: Spurious response
|
Parameter |
Unit |
Level |
|
PInterferer (CW) |
dBm |
-44 |
|
FInterferer |
MHz |
Spurious response frequencies |
7.7G.2 Spurious response for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions
7.7G.2.1 Test Purpose
Same test purpose as in clause 7.7G.1.
7.7G.2.2 Test applicability
This test case applies to all types of E-UTRA UE release 14 and forward that support V2X Communication.
7.7G.2.3 Minimum conformance requirements
The throughput shall be ≥ 95% of the maximum throughput of the reference measurement channels as specified in Annex A.8.2 with parameters specified in Tables 7.7G.2.3-1 and 7.7G.2.3-2.
Table 7.7G.2.3-1: Spurious response parameters
|
Rx parameter |
Units |
Channel bandwidth |
||||||
|
1.4 MHz |
3 MHz |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
|||
|
Power in Transmission Bandwidth Configuration |
dBm |
PREFSENS_V2X + channel bandwidth specific value below |
||||||
|
6 |
9 |
|||||||
|
NOTE 1: Reference measurement channel is specified in Annex A.8.2. |
||||||||
Table 7.7G.2.3-2: Spurious response
|
Parameter |
Unit |
Level |
|
PInterferer (CW) |
dBm |
-44 |
|
FInterferer |
MHz |
Spurious response frequencies |
When UE is configured for simultaneous E-UTRA V2X sidelink and E-UTRA downlink reception for inter-band E-UTRA V2X / E-UTRA bands specified in Table 5.5G-2, the requirements in subclause 7.7G.2.3 apply for the E-UTRA V2X sidelink reception and the requirements in subclause 7.7.3 apply for the E-UTRA downlink reception while all downlink carriers are active.
The normative reference for this requirement is TS 36.101 [2] clause 7.7.1G.
7.7G.2.4 Test description
7.7G.2.4.1 Initial conditions
The initial conditions shall be the same as in clause 7.6.2G.2.4.1 in order to test spurious responses obtained in clause 7.6.2G under the same conditions.
7.7G.2.4.2 Test Procedure
1. The SS transmits PDSCH via PDCCH DCI format 1A for C_RNTI to transmit the DL RMC according to Table 7.6.2G.2.4.1-1 on E-UTRA Band. The SS sends downlink MAC padding bits on the DL RMC.
2. SS simultaneously sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC and V2X scheduling information via PDCCH DCI format 5A for SL_V_RNTI to schedule the V2X RMC according to Table 7.6.2G.2.4.1-1. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL and V2X RMCs.
3. Set the parameters of the CW signal generator for an interfering signal according to Table 7.7G.2.5-2. The spurious frequencies are taken from records in the final step of test procedures in clause 7.6.2G.2.4.2.
4. Set the signal level of V2X to the value defined in table 7.7G.2.5-1.
5. For the spurious frequency, measure the average throughput for a duration sufficient to achieve statistical significance according to Annex G.2.
7.7G.2.4.3 Message Contents
Message contents are according to TS 36.508 [7] subclause 4.6.
7.7G.2.5 Test Requirement
The throughput shall be ≥ 95% of the maximum throughput of the reference measurement channels as specified in Annex A.8.2 with parameters specified in Tables 7.7G.2.5-1 and 7.7G.2.5-2.
Table 7.7G.2.5-1: Spurious response parameters
|
Rx parameter |
Units |
Channel bandwidth |
||||||
|
1.4 MHz |
3 MHz |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
|||
|
Power in Transmission Bandwidth Configuration |
dBm |
PREFSENS_V2X + channel bandwidth specific value below |
||||||
|
6 |
9 |
|||||||
|
NOTE 1: Reference measurement channel is specified in Annex A.8.2. |
||||||||
Table 7.7G.2.5-2: Spurious response
|
Parameter |
Unit |
Level |
|
PInterferer (CW) |
dBm |
-44 |
|
FInterferer |
MHz |
Spurious response frequencies |
When UE is configured for simultaneous E-UTRA V2X sidelink and E-UTRA downlink reception for inter-band E-UTRA V2X / E-UTRA bands specified in Table 5.5G-2, the requirements in subclause 7.7G.2.5 apply for the E-UTRA V2X sidelink reception and the requirements in subclause 7.7.3 apply for the E-UTRA downlink reception while all downlink carriers are active.
7.7G.3 Spurious response for V2X Communication / Intra-band contiguous multi-carrier operation
7.7G.3.1 Test Purpose
Same test purpose as in clause 7.7G.1.
7.7G.3.2 Test applicability
This test case applies to all types of UE that support Intra-band contiguous multi-carrier operation V2X Sidelink Communication and Band 47.
7.7G.3.3 Minimum conformance requirements
For intra-band contiguous multi-carrier operation, the V2X UE throughput shall be ≥ 95% of the maximum throughput of the reference measurement channels as specified in Annex A.8.2 with parameters specified in Table 7.7G.3.3-1 and Table 7.7G.3.3-2.
Table 7.7G.3.3-1: Spurious response parameters for intra-band contiguous multi-carrier for V2X UE
|
Rx Parameter |
Units |
V2X Bandwidth Class |
||||
|
B |
C |
D |
E |
F |
||
|
Pw in Transmission Bandwidth Configuration, per CC |
dBm |
REFSENS + V2X Bandwidth Class specific value below |
||||
|
9 |
||||||
|
NOTE 1: The requirement is applied for multi carrier intra-band con-concurrent receptions when 2 carrier transmission are activated at the same time |
||||||
Table 7.7.G.3.3-2: Spurious response for intra-band contiguous multi-carrier for V2X UE
|
Parameter |
Unit |
Level |
|
PInterferer (CW) |
dBm |
-44 |
|
FInterferer |
MHz |
Spurious response frequencies |
|
NOTE 1: The requirement is applied for multi- carrier intra-band con -concurrent receptions when 2 carrier transmissions are activated at the same time |
||
The normative reference for this requirement is TS 36.101 [2] clause 7.7.1G.
7.7G.3.4 Test description
7.7G.3.4.1 Initial conditions
The initial conditions shall be the same as in clause 7.6.2G.3.4.1 in order to test spurious responses obtained in clause 7.6.2G under the same conditions.
7.7G.3.4.2 Test Procedure
1. The UE starts to perform the V2X sidelink communication according to SL-V2X-Preconfiguration and to schedule the V2X RMC according to Table 7.6.2G.3.4.1-1. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the V2X RMC.
2. Set the parameters of the CW signal generator for an interfering signal according to Table 7.7G.3.5-2. The spurious frequencies are taken from records in the final step of test procedures in clause 7.6.2G.3.4.2.
3. Set the signal level of V2X to the value defined in table 7.7G.3.5-1.
4. For the spurious frequency, measure the average throughput for a duration sufficient to achieve statistical significance according to Annex G.2 .
7.7G.3.4.3 Message Contents
Message contents are according to TS 36.508 [7] subclause 4.6.
7.7G.3.5 Test Requirement
For intra-band contiguous multi-carrier operation, the V2X UE throughput shall be ≥ 95% of the maximum throughput of the reference measurement channels as specified in Annex A.8.2 with parameters specified in Table 7.7G.3.5-1 and Table 7.7G.3.5-2.
Table 7.7G.3.5-1: Spurious response parameters for intra-band contiguous multi-carrier for V2X UE
|
Rx Parameter |
Units |
V2X Bandwidth Class |
||||
|
B |
C |
D |
E |
F |
||
|
Pw in Transmission Bandwidth Configuration, per CC |
dBm |
REFSENS + V2X Bandwidth Class specific value below |
||||
|
9 |
||||||
|
NOTE 1: The requirement is applied for multi- carrier intra–band con concurrent receptions when 2 carrier transmissions are activated at the same time |
||||||
Table 7.7.G.3.5-2: Spurious response for intra-band contiguous multi-carrier for V2X UE
|
Parameter |
Unit |
Level |
|
PInterferer (CW) |
dBm |
-44 |
|
FInterferer |
MHz |
Spurious response frequencies |
|
NOTE 1: The requirement is applied for multi- carrier intra–band con concurrent receptions when 2 carrier transmissions are activated at the same time |
||