1.4 MHz

3 MHz

5 MHz

10 MHz

15 MHz

20 MHz

Power in Transmission Bandwidth Configuration

dBm

REFSENS + channel bandwidth specific value below

6

6

6

6

7

9

BW_Interferer

MHz

1.4

3

5

5

5

5

F_{Ioffset, case 1}

MHz

2.1+0.0125

4.5+0.0075

7.5+0.0125

7.5+0.0025

7.5+0.0075

7.5+0.0125

F_{Ioffset, case 2}

MHz

3.5+0.0075

7.5+0.0075

12.5+0.0075

12.5+0.0125

12.5+0.0025

12.5+0.0075

NOTE 1: The transmitter shall be set to 4dB below PCMAX_L at the minimum uplink configuration specified in Table 7.3EA-3 with PCMAX_L as defined in subclause 6.2.5EA.

NOTE 2: The interferer consists of the Reference measurement channel specified in Annex A.3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD as described in Annex A.5.1.1/A.5.2.1 and set-up according to Annex C.3.1.

NOTE 3: For DL category M1 and M2 UE, the reference sensitivity for category M1 in table 7.3EA-1 and 7.3EA-2 and category M2 in Table 7.3EC-1 should be used as REFSENS for the power in Transmission Bandwidth Configuration.

NOTE 4: For DL category M1 and M2 UE, the parameters for the applicable channel bandwidth apply.

P_Interferer

dBm

-56

-44

Void

Void

-38

F_Interferer (offset)

MHz

=-BW/2 – F_{Ioffset,case 1}

&

=+BW/2 + F_{Ioffset,case 1}

≤-BW/2 – F_{Ioffset,case 2}

&

≥+BW/2 + F_{Ioffset,case 2}

-BW/2 – 11

1, 2, 3, 4, 5, 7, 8, 11, 12, 13, 14, 18, 19, 20, 21, 26, 27, 28, 31, 39, 41, 42, 43

F_Interferer

MHz

(NOTE 2)

F_{DL_low} – 15

to

F_{DL_high} + 15

NOTE 1: For certain bands, the unwanted modulated interfering signal may not fall inside the UE receive band, but within the first 15 MHz below or above the UE receive band

NOTE 2: For each carrier frequency the requirement is valid for two frequencies:

a. the carrier frequency -BW/2 – F_{Ioffset, case 1} and

b. the carrier frequency +BW/2 + F_{Ioffset, case 1}

NOTE 3: F_Interferer range values for unwanted modulated interfering signal are interferer centre frequencies

Test Environment as specified in

TS 36.508[7] clause 4.1

NC

Test Frequencies as specified in

TS36.508 [7] clause 4.3.1

Mid range

Test Channel Bandwidths as specified in TS 36.508 [7] clause 4.3.

1.4, 3MHz, 5MHz

Test Parameters for Channel Bandwidths and Narrowband positions

Downlink Configuration

Uplink Configuration

Ch BW

Mod’n

RB allocation

Mod’n

RB allocation

FDD and HD-FDD

TDD

FDD and HD-FDD

TDD

1.4MHz

QPSK

4

4

QPSK

6

6

3MHz

QPSK

8

8

QPSK

15

15

5MHz

QPSK

16

16

QPSK

24

24