7.6.1A.10 In-band blocking for 7DL CA

36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification

Tools: ARFCN - Frequency Conversion for 5G NR/LTE/UMTS/GSM

7.6.1A.10.1 Test Purpose

Same test purpose as in clause 7.6.1A.1.

7.6.1A.10.2 Test Applicability

This test case applies to all types of E-UTRA UE and forward that support 7DL with CA configurations in Table 7.1-2e.

7.6.1A.10.3 Minimum Conformance Requirements

The minimum conformance requirements are defined in clause 7.6.1A.0.

7.6.1A.10.4 Test Description

7.6.1A.10.4.1 Initial Conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and channel bandwidths based on E-UTRA CA configurations specified in table 5.4.2A.1-1 through table 5.4.2A.1-2a. All of these configurations shall be tested with applicable test parameters for each channel bandwidth, and are shown in table 7.6.1A.10.4.1-1. The details of the uplink reference measurement channels (RMCs) are specified in Annex A.2 and A.3. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2

Table 7.6.1A.10.4.1-1: Test Configuration Table

Initial Conditions

Test Environment as specified in

TS 36.508 [7] subclause 4.1

Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes.

For test frequencies refer to “Range” columns. For mapping within Band refer to “CC” columns

Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.

Refer to “PCC NRB” and “SCCs NRB” columns

Network signalling value

NS_01 by default

Test Parameters for CA Configurations

PCC

SCC1

SCC2

SCC3

SCC4

SCC5

SCC6

Band

Range

NRB

Band

Range

NRB

Band

Range

NRB

Band

Range

NRB

Band

Range

NRB

Band

Range

NRB

Band

Range

NRB

UL MOD

ULalloc (Note 2,3,4)

UL MOD

DL MOD

MOD

alloc

MOD

alloc

MOD

alloc

MOD

alloc

MOD

alloc

MOD

alloc

MOD

alloc

Default Test Settings for CA_XA-YC-ZE Configuration (Intra-band contiguous + Inter-band)

Mid

REF

ALL RBs

Mid/

N/A

Mid

Mid/

N/A

Mid

Mid/

N/A

Mid

Mid/

N/A

Mid

Mid/

N/A

Mid

Mid/

N/A

Mid

SENS

CC1

CC2

CC1

CC2

CC3

CC4

QPSK

Highest N_RB

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

Mid/

REF

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid

N/A

ALL RBs

CC1

SENS

CC2

CC1

CC2

CC3

CC4

QPSK

Highest N_RB

N/A

QPSK

Highest N_RB

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

QPSK

Highest N_RB

Mid/

REF

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

Mid

Mid/

N/A

Mid

N/A

ALL RBs

CC1

SENS

CC2

CC3

CC4

CC1

CC2

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest N_RB

Default Test Settings for CA_XA-YA-ZC-RD Configuration (Intra-band contiguous + Inter-band(2))

Mid

REF

ALL RBs

Mid

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

SENS

CC1

CC2

CC1

CC2

CC3

QPSK

Highest N_RB

N/A

QPSK

Highest N_RB

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

Mid

REF

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid

N/A

ALL RBs

SENS

CC1

CC2

CC1

CC2

CC3

QPSK

Highest N_RB

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest N_RB

Mid

REF

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid/

N/A

ALL RBs

Mid

N/A

ALL RBs

SENS

CC1

CC2

CC3

CC1

CC2

QPSK

Highest N_RB

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest NRB_agg

N/A

QPSK

Highest N_RB

Note 1: CA Configuration Test CC Combination test settings are checked separately for each CA Configuration.

Note 2: Intra-band contiguous+ Inter-band: Use CA Configuration – specific test points if present in the table, otherwise use Default Test Settings test points.

Note 3: Inter-band: Use CA Configuration – specific test points if present in the table, Otherwise use test points from matching Group Test Settings, if present in the table. Otherwise use the Default Test Settings test points.

Note 4: If, according to the UE declared capability, UE does not support UL in an individual band within the CA Configuration, test points with that individual band as PCC are not applicable.

Note 5: Intra-band contiguous: X corresponds to the band of the CA Configuration. E.g. for CA_41F, X=41.

Note 6: Inter-band: X,Y,Z and R correspond to the different bands in the CA Configuration. E.g. X !=Y !=Z !=R.

Note 7: REFSENS refers to the PCC bands and PCC N_RB ‘s single carrier Uplink RB allocation for reference sensitivity according to table 7.3.5-2.

Note 8: Intra-band contiguous: If in the CA Configuration UE supports multiple CC Combinations with the same N_{RB_agg}, choose for testing the Combination with maximum N_{RB_PCC} and then select maximum N_{RB_SCC1}for the chosen N_{RB_PCC.}

Note 9: Intra-band contiguous + Inter-band: If in the CA Configuration UE supports multiple CC Combinations with the same N_{RB_agg}, choose the Combination with N_{RB_PCC} = N_{RB_SCC1} for testing. If no such combination is supported, choose Combination with maximum N_{RB_PCC} for testing.

Note 10: The orders and numbering of SCCs in this table does not imply any order in test implementation of SCCs.

Note 11: ID/test points that result in no ref sens requirement shall be skipped.

1. Connect the SS to the UE antenna connectors as shown in TS 36.508[7] Annex A Figure A.58 as appropriate if the UE supports 2 Rx antennas or Figure A.82 if the UE supports 4 Rx antennas in the band.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals for PCC are initially set up according to Annex C.0, C.1, and C.3.1, and uplink signals according to Annex H.1 and H.3.0.

4. The UL and DL Reference Measurement channels are set according to Table 7.6.1A.10.4.1-1.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 7.6.1A.10.4.3.

7.6.1A.10.4.2 Test Procedure

1. Configure SCCs according to Annex C.0, C.1 and Annex C.3.1 for all downlink physical channels.

2. The SS shall configure SCCs as per TS 36.508 [7] clause 5.2A.4. Message contents are defined in clause 7.6.1A.10.4.3

3. SS activates SCCs by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

4. SS transmits PDSCH via PDCCH DCI format 1A for C_RNTI to transmit the DL RMC according to Table 7.6.1A.10.4.1-1 on PCC and SCCs. The SS sends downlink MAC padding bits on the DL RMC.

5. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 7.6.1A.10.4.1-1 on PCC. Since the UE has no payload data to send, the UE sends uplink MAC padding bits on the UL RMC.

6 Set the parameters of the signal generator for an interfering signal below the aggregated component carriers in Case 1 according to Table 7.6.1A.10.4.2-1.

7 Set the downlink signal level according to the Table 7.6.1A.10.4.2-1. Send uplink power control commands to the UE (less or equal to 1dB step size should be used), to ensure that the UE output power is within +0, – 3.4 dB of the target level in table 7.6.1A.10.5-1 or 7.6.1A.10.5-3 or 7.6.1A.10.5-5 and Table 7.6.1A.10.5-1b and 7.6.1A.10.5-3b for operating band 46 for carrier frequency f ≤ 3.0GHz or within +0, -4.0 dB of the target level for carrier frequency 3.0GHz < f ≤ 4.2GHz, for at least the duration of the throughput measurement.

8 Measure the average throughput for the carrier(s) indicated in Table 7.6.1A.10.4.2-1for duration sufficient to achieve statistical significance according to Annex G.2A.

9 Repeat steps from 6 to 8, using an interfering signal above the measured carrier(s) according to Table 7.6.1A.10.5-1 or 7.6.1A.10.5-3 or 7.6.1A.10.5-5, and Table 7.6.1A.10.5-1b and 7.6.1A.10.5-3b for operating band 46 in Case 1 at step 6.

10 Repeat steps from 6 to 9 using interfering signals in Case 2at step 6 and 9. The ranges of case 2 are covered in steps equal to the interferer bandwidth. The test frequencies are chosen in analogy to table 7.6.1A.1.4.2-1.

11.Repeat steps 1 to 10 for all component carriers listed in Table 7.6.1A.10.4.2-1.

Table 7.6.1A.10.4.2-1: Test repetition and measurement configuration

CA configuration	ID (Note 1)	Throughput measured on (Note 3)	Table with test parameters to select (Note 2)

Intra-band contiguous + Inter-band	1	SCC1, SCC2, SCC3, SCC4, SCC5, SCC6	7.6.1A.10.5-2 7.6.1A.10.5-3 7.6.1A.10.5-3a 7.6.1A.10.5-3b



	2	PCC, SCC1, SCC2, SCC3, SCC4, SCC5	7.6.1A.10.5-2 7.6.1A.10.5-3 7.6.1A.10.5-3a 7.6.1A.10.5-3b

		SCC6	7.6.1A.10.5-1 7.6.1A.10.5-1a 7.6.1A.10.5-1b
	3	PCC, SCC1, SCC2, SCC3, SCC4, SCC5	7.6.1A.10.5-2 7.6.1A.10.5-3 7.6.1A.10.5-3a 7.6.1A.10.5-3b
		SCC6	7.6.1A.10.5-1 7.6.1A.10.5-1a 7.6.1A.10.5-1b
Intra-band contiguous + Inter-band(2)	1	SCC1	7.6.1A.10.5-1 7.6.1A.10.5-1a 7.6.1A.10.5-1b
		SCC2, SCC3, SCC4, SCC5, SCC6	7.6.1A.10.5-2 7.6.1A.10.5-3 7.6.1A.10.5-3a 7.6.1A.10.5-3b

	2	SCC1, SCC2, SCC3, SCC4, SCC5	7.6.1A.10.5-2 7.6.1A.10.5-3 7.6.1A.10.5-3a 7.6.1A.10.5-3b
		SCC6	7.6.1A.10.5-1 7.6.1A.10.5-1a 7.6.1A.10.5-1b
	3	SCC1, SCC2, SCC3, SCC4, SCC5	7.6.1A.10.5-2 7.6.1A.10.5-3 7.6.1A.10.5-3a 7.6.1A.10.5-3b
		SCC6	7.6.1A.10.5-1 7.6.1A.10.5-1a 7.6.1A.10.5-1b
Note 1: Test point ID for the particular CA configuration as defined in section 7.6.1A.10.4.1.
Note 2: The reference for the placement of the interferer signals is the centre frequency of the carrier closest to the interferer among the carriers throughput is measured on.
Note 3: Where there are multiple rows for a single Test point ID, the test is repeated for each row.

7.6.1A.10.4.3 Message Contents

Same message contents as in clause 7.6.1.4.3 for without UL CA.

Same message contents as in clause 7.6.1A.1.4.3 for UL CA.

7.6.1A.10.5 Test Requirement

The throughput measurement of each carrier derived in test procedure shall be ≥ 95% of the maximum throughput of the reference measurement channels as specified in Annex A.3.2 with parameters specified in Table s below, according to the type of CA.

Table 7.6.1A.10.5-1: In-band blocking for additional operating bands for carrier aggregation (inter‑band)

E-UTRA band	Parameter	Unit	Case 1	Case 2
	P_Interferer	dBm	-56	-44
	F_Interferer (offset from SCC)	MHz	=-BW/2 – F_{Ioffset,case 1} & =+BW/2 + F_{Ioffset,case 1}	≤-BW/2 – F_{Ioffset,case 2} & ≥+BW/2 + F_{Ioffset,case 2}
29, 32, 67, 69	F_Interferer	MHz	(Note 2)	F_{DL_low}– 15 to F_{DL_high}+ 15
Note 1: For certain bands, the unwanted modulated interfering signal may not fall inside the UE receive band, but within the first 15 MHz below or above the UE receive band. Note 2: For each carrier frequency the requirement is valid for two frequencies: a. the carrier frequency -BW/2 – F_{Ioffset, case 1}and b. the carrier frequency +BW/2 + F_{Ioffset, case 1} Note 3: F_Interferer range values for unwanted modulated interfering signal are interferer centre frequencies.

Table 7.6.1A.10.5-1a: In band blocking parameters for additional operating bands for carrier aggregation (inter‑band)

E-UTRA band	Rx parameter	Units	Channel bandwidth
E-UTRA band	Rx parameter	Units	1.4 MHz	3 MHz	5 MHz	10 MHz	15 MHz	20 MHz
46 (NOTE 3)	Power in Transmission Bandwidth Configuration	dBm	REFSENS + channel bandwidth specific value below
	Power in Transmission Bandwidth Configuration	dBm				6		9
	BW_Interferer	MHz				20		20
	F_{Ioffset, case 1}	MHz				30+0.0025		30+0.0125
	F_{Ioffset, case 2}	MHz				50+0.0125		50+0.0075
49 (NOTE 3)	Power in Transmission Bandwidth Configuration	dBm				6		6
	BW_Interferer	MHz				10		20
	F_{Ioffset, case 1}	MHz				15+0.025		30+0.125
	F_{Ioffset, case 2}	MHz				25+0.075		50+0.075
NOTE 1: The transmitter shall be set to 4dB below PCMAX_L at the minimum uplink configuration specified in Table 7.3.1-2 with PCMAX_L as defined in subclause 6.2.5. NOTE 2: The interferer consists of the Reference measurement channel specified in Annex A.3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD/FS3 as described in Annex A.5.1.1/A.5.2.1/A.5.4.1 and set-up according to Annex C.3.1 NOTE 3: The interferer consists of the Reference measurement channel specified in Annex A.3.2 (TBD)

Table 7.6.1A.10.5-1b: In-band blocking for additional operating bands for carrier aggregation (inter‑band)

E-UTRA band	Parameter	Unit	Case 1	Case 2
	P_Interferer	dBm	-50	-44
	F_Interferer (offset)	MHz	=-BW/2 – F_{Ioffset,case 1} & =+BW/2 + F_{Ioffset,case 1}	≤-BW/2 – F_{Ioffset,case 2} & ≥+BW/2 + F_{Ioffset,case 2}
46, 49	F_Interferer	MHz	(Note 2)	F_{DL_low}– 60 to F_{DL_high}+ 60
NOTE 1: For certain bands, the unwanted modulated interfering signal may not fall inside the UE receive band, but within the first 15 MHz or 60 MHz below or above the UE receive band NOTE 2: For each carrier frequency the requirement is valid for two frequencies: a. the carrier frequency -BW/2 – F_{Ioffset, case 1}and b. the carrier frequency +BW/2 + F_{Ioffset, case 1} NOTE 3: F_Interferer range values for unwanted modulated interfering signal are interferer centre frequencies

Table 7.6.1A.10.5-2: In band blocking parameter (intra-band contiguous)

Rx Parameter	Units	CA Bandwidth Class
Rx Parameter	Units	B	C	D	E	F
Pw in Transmission Bandwidth Configuration, per CC	dBm	REFSENS + CA Bandwidth Class specific value below
Pw in Transmission Bandwidth Configuration, per CC	dBm	9	12	13.8	15	16
BW_Interferer	MHz	5	5	5	5	5
F_{Ioffset, case 1}	MHz	7.5	7.5	7.5	7.5	7.5
F_{Ioffset, case 2}	MHz	12.5	12.5	12.5	12.5	12.5
NOTE 1: The transmitter shall be set to 4dB below PCMAX_L,c or PCMAX_L as defined in subclause 6.2.5A NOTE 2: The interferer consists of the Reference measurement channel specified in Annex A.3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD as described in Annex A.5.1.1/A.5.2.1 and set-up according to Annex C.3.1

Table 7.6.1A.10.5-3: In-band blocking (intra-band contiguous)

CA configuration	Parameter	Unit	Case 1	Case 2
	P_Interferer	dBm	-56	-44
	F_Interferer (offset)	MHz	=-F_offset– F_{Ioffset,case 1} & =+F_offset + F_{Ioffset,case 1}	≤-F_offset– F_{Ioffset,case 2} & ≥+F_offset + F_{Ioffset,case 2}
CA_1C, CA_2C, CA_3B, CA_3C, CA_5B, CA_7B, CA_7C, CA_8B, CA_12B, CA_23B, CA_27B, CA_28C, CA_38C, CA_39C, CA_40C, CA_40D, CA_40E, CA_40F, CA_41C, CA_41D, CA_41E, CA_41F, CA_42C, CA_42D, CA_42E, CA_42F, CA_43C, CA_48C, CA_48D, CA_48E, CA_48F, CA_66B, CA_66C, CA_66D, CA_70C	F_Interferer (Range)	MHz	(NOTE 2)	F_{DL_low}– 15 to F_{DL_high}+ 15
NOTE 1: For certain bands, the unwanted modulated interfering signal may not fall inside the UE receive band, but within the first 15 MHz below or above the UE receive band NOTE 2: For each carrier frequency the requirement is valid for two frequencies: a. the carrier frequency -F_offset – F_{Ioffset, case 1}and b. the carrier frequency +F_offset + F_{Ioffset, case 1} NOTE 3: F_offset is the frequency offset from the centre frequency of the CC being tested to the edge of aggregated channel bandwidth. NOTE 4: The F_interferer (offset) is the frequency separation of the centre frequency of the carrier closest to the interferer and the centre frequency of the interferer and shall be further adjusted to MHz to be offset from the sub-carrier raster.

Table 7.6.1A.10.5-3a: In band blocking parameters (intra-band contiguous)

E-UTRA Band	Rx Parameter	Units	CA Bandwidth Class
E-UTRA Band	Rx Parameter	Units	B	C	D	E	F
46	Pw in Transmission Bandwidth Configuration, per CC	dBm	REFSENS + CA Bandwidth Class specific value below
	Pw in Transmission Bandwidth Configuration, per CC	dBm		12	13.8	15
	BW_Interferer	MHz		20	20	20
	F_{Ioffset, case 1}	MHz		30	30	30
	F_{Ioffset, case 2}	MHz		50	50	50
NOTE 1: In a band capable of uplink operation, the transmitter shall be set to 4dB below PCMAX_L,c or PCMAX_L as defined in subclause 6.2.5A NOTE 2: The interferer consists of the Reference measurement channel specified in Annex A.3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD/FS3 as described in Annex A.5.1.1/A.5.2.1/A.5.4.1 and set-up according to Annex C.3.1

Table 7.6.1A.10.5-3b: In-band blocking (intra-band contiguous)

E-UTRA Band	Parameter	Unit	Case 1	Case 2
	P_Interferer	dBm	-50	-44
	F_Interferer (offset)	MHz	=-F_offset– F_{Ioffset,case 1} & =+F_offset + F_{Ioffset,case 1}	≤-F_offset– F_{Ioffset,case 2} & ≥+F_offset + F_{Ioffset,case 2}
46	F_Interferer (Range)	MHz	(Note 2)	F_{DL_low}– 60 to F_{DL_high}+ 60
NOTE 1: For certain bands, the unwanted modulated interfering signal may not fall inside the UE receive band, but within the first 15 MHz below or above the UE receive band NOTE 2: For each carrier frequency the requirement is valid for two frequencies: a. the carrier frequency -F_offset – F_{Ioffset, case 1}and b. the carrier frequency +F_offset + F_{Ioffset, case 1} NOTE 3: F_offset is the frequency offset from the centre frequency of the CC being tested to the edge of aggregated channel bandwidth. NOTE 4: The F_interferer (offset) is the frequency separation of the centre frequency of the carrier closest to the interferer and the centre frequency of the interferer and shall be further adjusted to MHz to be offset from the sub-carrier raster.

Table 7.6.1A.10.5-4: In-band blocking parameters (inter-band, intra-band non-contiguous)

Rx Parameter	Units	Channel bandwidth
Rx Parameter	Units	1.4 MHz	3 MHz	5 MHz	10 MHz	15 MHz	20 MHz
Power in Transmission Bandwidth Configuration for each CC	dBm	REFSENS + channel bandwidth specific value below
Power in Transmission Bandwidth Configuration for each CC	dBm	6	6	6	6	7	9
BW_Interferer	MHz	1.4	3	5	5	5	5
F_{Ioffset, case 1}	MHz	2.1+0.0125	4.5+0.0075	7.5+0.0125	7.5+0.0025	7.5+0.0075	7.5+0.0125
F_{Ioffset, case 2}	MHz	3.5+0.0075	7.5+0.0075	12.5+0.0075	12.5+0.0125	12.5+0.0025	12.5+0.0075
Note 1: The transmitter shall be set to 4dB below P_{CMAX_L}with P_{CMAX_L}as defined in clause 6.2.5. Note 2: The interferer consists of the Reference measurement channel specified in Annex A.3.2 with one sided dynamic OCNG Pattern OP.1 FDD/TDD as described in Annex A.5.1.1/A.5.2.1 and set-up according to Annex C.3.1.

Table 7.6.1A.10.5-5: In-band blocking (inter-band, intra-band non-contiguous)

E-UTRA band	Parameter	Unit	Case 1	Case 2	Case 3	Case 4	Case 5	Case 6
	P_Interferer	dBm	-56	-44	Void	Void	-38	-15
	F_Interferer (offset from SCC)	MHz	=-BW/2 – F_{Ioffset,case 1} & =+BW/2 + F_{Ioffset,case 1}	≤-BW/2 – F_{Ioffset,case 2} & ≥+BW/2 + F_{Ioffset,case 2}			-BW/2 – 11
1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 17, 18, 19, 20, 21, 22, 23, 25, 26, 27, 28, 31, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 65, 66, 68, 70, 72. 73, 74, 85	F_Interferer	MHz	(Note 2)	F_{DL_low}– 15 to F_{DL_high}+ 15
30	F_Interferer	MHz	(Note 2)	F_{DL_low}– 15 to F_{DL_high}+ 15			F_{DL_low}– 11
71	F_Interferer	MHz	(NOTE 2)	F_{DL_low}– 12 to F_{DL_high}+ 15				F_DL-low– 12
Note 1: For certain bands, the unwanted modulated interfering signal may not fall inside the UE receive band, but within the first 15 MHz below or above the UE receive band. Note 2: For each carrier frequency the requirement is valid for two frequencies: a. the carrier frequency -BW/2 – F_{Ioffset, case 1}and b. the carrier frequency +BW/2 + F_{Ioffset, case 1} Note 3: F_Interferer range values for unwanted modulated interfering signal are interferer centre frequencies. Note 4: For intra-band non-contiguous + inter-band CA, DR_IBNC = 0 dB for all sub-block gaps.

For a UE, which supports CA configuration in Tables 7.3.3-1A, 7.3.3-1B and 7.3.3-1C, PInterferer power defined in Tables 7.6.1A.10.5-1, 7.6.1A.10.5-3 and 7.6.1A.10.5-5 is increased by the amount given by ΔRIB,c in Tables 7.3.3-1A, 7.3.3-1B and 7.3.3-1C accordingly.