7.4A.3 Maximum input level for CA (inter-band DL CA without UL CA)
36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification
Editor’s note:
– Any restriction of the applicability of test points due to the supported UE category is under investigation
7.4A.3.1 Test purpose
Same test purpose as in clause 7.4A.1.1
7.4A.3.2 Test applicability
This test applies to all types of E-UTRA UE release 10 and forward that support inter-band DL CA.
This test case also applies to all types of E-UTRA UE release 12 and forward that support 2DL CA with FDD-TDD inter-band CA.
This test case also applies to all types of E-UTRA UE release 13 and forward that support DL LAA.
This test case applies only for CA configurations that do not support UL CA.
7.4A.3.3 Minimum conformance requirements
The minimum conformance requirements are defined in clause 7.4A.0.
7.4A.3.4 Test description
7.4A.3.4.1 Initial conditions
Same initial conditions as in clause 7.4A.1.4.1 with the following exceptions:
– Instead of Table 7.4A.1.4.1-1 🡪 use Table 7.4A.3.4.1-1.
– Instead of clause 7.4A.1.4.3 🡪 use clause 7.4A.3.4.3.
Table 7.4A.3.4.1-1: Test Configuration Table
Initial Conditions |
||||||
Test Environment as specified in TS 36.508[7] subclause 4.1 |
NC |
|||||
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 7.1-2 |
A: Mid range for PCC and SCC |
|||||
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE |
Highest NRB_agg for PCC and SCC |
|||||
Test Parameters for CA Configurations |
||||||
CA Configuration / NRB_agg |
DL Allocation |
UL Allocation |
||||
PCC |
SCCs |
CC |
PCC & SCC |
CC |
PCC |
|
50 |
50 |
64-QAM |
50 |
50 |
QPSK |
50 |
50 |
50 |
64-QAM |
50 |
50 |
QPSK |
25 |
50 |
50 |
64-QAM |
50 |
50 |
QPSK |
20 |
50 |
50 |
64-QAM |
50 |
50 |
QPSK |
16 |
50 |
75 |
64-QAM |
50 |
75 |
QPSK |
25 |
50 |
100 |
64-QAM |
50 |
100 |
QPSK |
50 |
50 |
100 |
64-QAM |
50 |
100 |
QPSK |
25 |
50 |
100 |
64-QAM |
50 |
100 |
QPSK |
20 |
50 |
100 |
64-QAM |
50 |
100 |
QPSK |
16 |
75 |
25 |
64-QAM |
75 |
25 |
QPSK |
75 |
75 |
25 |
64-QAM |
75 |
25 |
QPSK |
20 |
75 |
50 |
64-QAM |
75 |
50 |
QPSK |
25 |
75 |
75 |
64-QAM |
75 |
75 |
QPSK |
25 |
75 |
100 |
64-QAM |
75 |
100 |
QPSK |
25 |
100 |
50 |
64-QAM |
100 |
50 |
QPSK |
100 |
100 |
50 |
64-QAM |
100 |
50 |
QPSK |
75 |
100 |
50 |
64-QAM |
100 |
50 |
QPSK |
50 |
100 |
75 |
64-QAM |
100 |
75 |
QPSK |
100 |
100 |
75 |
64-QAM |
100 |
75 |
QPSK |
50 |
100 |
100 |
64-QAM |
100 |
100 |
QPSK |
100 |
100 |
100 |
64-QAM |
100 |
100 |
QPSK |
75 |
100 |
100 |
64-QAM |
100 |
100 |
QPSK |
50 |
100 |
100 |
64-QAM |
100 |
100 |
QPSK |
45 |
100 |
100 |
64-QAM |
100 |
100 |
QPSK |
25 |
100 |
100 |
64-QAM |
100 |
100 |
QPSK |
20 |
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration, which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-2. Note 2: Depending on CA configurations, only the appropriate Uplink RB allocation value according to table 7.3A.3.5-2 for UE supporting one uplink carrier is tested per Test CA configuration. Note 3: The UL resource blocks shall be located as close as possible to the downlink PCC but confined within the transmission bandwidth configuration for the channel bandwidth (Table 5.4.2-1). Note 4: The frequencies of PCC and SCC shall be switched and tested in each configuration, according to the UE declared capability for UL support (within CA operation) in the individual bands. |
7.4A.3.4.2 Test procedure
1. Configure SCC according to Annex C.0, C.1 and Annex C.3.1 for all downlink physical channels.
2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4.
3. SS activates SCC by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).
4. SS transmits PDSCH via PDCCH DCI format 1A for C_RNTI to transmit the DL RMC according to Tables 7.4A.3.4.1-1 on both PCC and SCC. The SS sends downlink MAC padding bits on the DL RMC.
5. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 7.4A.3.4.1-1 on PCC. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.
6. Set the Downlink signal level to the value as defined in Table 7.4A.3.5-1. Send Uplink power control commands to the UE (less or equal to 1dB step size should be used), to ensure that the UE output power is within +0, – 3.4 dB of the target level in Table 7.4A.3.5-1 for carrier frequency f ≤ 3.0GHz or within +0, -4.0 dB of the target level for carrier frequency 3.0GHz < f ≤ 4.2GHz, for at least the duration of the Throughput measurement.
7. Measure the average throughput of SCC for a duration sufficient to achieve statistical significance according to Annex G.2.
7.4A.3.4.3 Message contents
Same message contents as in clause 7.4.4.3.
7.4A.3.5 Test requirement
For inter-band carrier aggregation with uplink assigned to one E-UTRA band the maximum input level is defined with the uplink active on the band other than the band whose downlink is being tested, i.e. the requirements are tested only for the SCell downlink. The UE shall meet the requirement for each component carrier, when operated as SCell, while both downlink carriers are active.
The throughput measured during the test procedure for each component carrier, when operated as SCell, shall be ≥ 95% of the maximum throughput of the reference measurement channels as specified in Annex A.3.2 with parameters specified in Table 7.4A.3.5-1 (originated from the single carrier Table 7.4.5-1).
Table 7.4A.3.5-1: Maximum input level for inter-band DL CA without UL CA
Rx Parameter |
Units |
Channel bandwidth |
|||||
1.4 MHz |
3 MHz |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
||
Power in Transmission Bandwidth Configuration for each CC |
dBm |
For carrier frequency f ≤ 3.0GHz: -25.7 For carrier frequency 3.0GHz < f ≤ 4.2GHz: -26.0 For carrier frequency 4.2GHz < f ≤ 6.0GHz: -26.5 |
|||||
Note 1: The transmitter shall be set to 4dB below PCMAX_L with PCMAX_L as defined in clause 6.2.5. Note 2: Reference measurement channel is Annex A.3.2 64QAM R=3/4variant with one sided dynamic OCNG Pattern OP.1 FDD/TDD as described in Annex A.5.1.1/A.5.2.1. |