7.4_1 Maximum input level with 4 Rx antenna ports

36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification

7.4_1.1 Test purpose

Same test purpose as in clause 7.4.1.

7.4_1.2 Test applicability

This test applies to all types of E-UTRA UE release 10 and forward that supports 4 Rx antenna ports but not 256QAM in DL.

7.4_1.3 Minimum conformance requirements

Same minimum conformance requirements as in clause 7.4.3.

7.4_1.4 Test description

7.4_1.4.1 Initial conditions

Same as in clause 7.4.4.1 with following exceptions:

– Instead of Table 7.4.4.1-1🡪 use Table 7.4_1.4.1-1.

– Instead of Figure A.3🡪 use Figure A.69.

Table 7.4_1.4.1-1: Test Configuration Table

Initial Conditions

Test Environment as specified in

TS 36.508[7] subclause 4.1

NC

Test Frequencies as specified in

TS36.508 [7] subclause 4.3.1

Mid range

Test Channel Bandwidths as specified in TS 36.508 [7] subclause 4.3.1

Lowest, 5MHz, Highest

Test Parameters for Channel Bandwidths

Downlink Configuration

Uplink Configuration

Ch BW

Mod’n

RB allocation

Mod’n

RB allocation

FDD

TDD

FDD

TDD

1.4MHz

64QAM

6

N/A

QPSK

6

N/A

3MHz

64QAM

15

N/A

QPSK

15

N/A

5MHz

64QAM

25

N/A

QPSK

25

N/A

10MHz

64QAM

50

N/A

QPSK

50

N/A

10MHz

64QAM

50

N/A

QPSK

20

N/A

15MHz

64QAM

75

N/A

QPSK

75

N/A

15MHz

64QAM

75

N/A

QPSK

50

N/A

15MHz

64QAM

75

N/A

QPSK

20

N/A

20MHz

64QAM

100

100

QPSK

100

100

20MHz

64QAM

100

N/A

QPSK

75

N/A

20MHz

64QAM

100

N/A

QPSK

50

N/A

20MHz

64QAM

100

N/A

QPSK

20

N/A

Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, which applicable channel bandwidths are specified in Table 5.4.2.1-1.

Note 2. Depending on E-UTRA band, only the appropriate Uplink RB allocation value according to table 7.3.3-2 is tested per Test Channel Bandwidth. The allocation shall be located as close as possible to the downlink operating band but confined within the transmission bandwidth configuration for the channel bandwidth (Table 5.4.2-1).

Note 3: For the DL signal one sided dynamic OCNG Pattern OP.1 FDD/TDD is used.

7.4_1.4.2 Test procedure

Same as in clause 7.4.4.2 with following exceptions:

– Instead of Table 7.4.4.1-1🡪 use Table 7.4_1.4.1-1.

7.4_1.4.3 Message contents

Same as in clause 7.4.4.3.

7.4_1.5 Test requirement

The throughput shall be ≥ 95% of the maximum throughput of the reference measurement channels as specified in Annex A.3.2 with parameters specified in Table 7.4_1.5-1.

Table 7.4_1.5-1: Maximum input level

Rx Parameter

Units

Channel bandwidth

1.4 MHz

3 MHz

5 MHz

10 MHz

15 MHz

20 MHz

Power in Transmission Bandwidth Configuration

dBm

For carrier frequency f ≤ 3.0GHz: -25.7

For carrier frequency 3.0GHz < f ≤ 4.2GHz: -26.0

Note 1: The transmitter shall be set to 4dB below PCMAX_L with PCMAX_L as defined in clause 6.2.5.

Note 2: Reference measurement channel is Annex A.3.2 64QAM R=3/4variant with one sided dynamic OCNG Pattern OP.1 FDD/TDD as described in Annex A.5.1.1/A.5.2.1.