6.6.3 Spurious emissions

36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification

Tools: ARFCN - Frequency Conversion for 5G NR/LTE/UMTS/GSM

Spurious emissions are emissions which are caused by unwanted transmitter effects such as harmonics emission, parasitic emissions, intermodulation products and frequency conversion products, but exclude out of band emissions. The spurious emission limits are specified in terms of general requirements inline with SM.329 [3] and E-UTRA operating band requirement to address UE co-existence.

Unless otherwise stated, the spurious emission limits apply for the frequency ranges that are more than Δf_OOB (MHz) in Table6.6.3.1.3-1 from the edge of the channel bandwidth. To improve measurement accuracy, sensitivity and efficiency, the resolution bandwidth may be smaller than the measurement bandwidth. When the resolution bandwidth is smaller than the measurement bandwidth, the result should be integrated over the measurement bandwidth in order to obtain the equivalent noise bandwidth of the measurement bandwidth.

6.6.3.1 Transmitter Spurious emissions

6.6.3.1.1 Test purpose

To verify that UE transmitter does not cause unacceptable interference to other channels or other systems in terms of transmitter spurious emissions.

6.6.3.1.2 Test applicability

This test case applies to all types of E-UTRA UE release 8 and forward.

6.6.3.1.3 Minimum conformance requirements

This clause specifies the requirements for the specified E-UTRA band for Transmitter Spurious emissions requirement with frequency range as indicated in table 6.6.3.1.3-2.

The spurious emission limits apply for the frequency ranges that are more than Δf_OOB (MHz) from the edge of the channel bandwidth.

NOTE: For measurement conditions at the edge of each frequency range, the lowest frequency of the measurement position in each frequency range should be set at the lowest boundary of the frequency range plus MBW/2. The highest frequency of the measurement position in each frequency range should be set at the highest boundary of the frequency range minus MBW/2. MBW denotes the measurement bandwidth defined for the protected band.

Table 6.6.3.1.3-1: Δf_OOB boundary between E-UTRA channel and spurious emission domain

Channel bandwidth	1.4 MHz	3.0 MHz	5 MHz	10 MHz	15 MHz	20 MHz
Δf_OOB (MHz)	2.8	6	10	15	20	25

The spurious emission limits in Table 6.6.3.1.3-2 apply for all transmitter band configurations (RB) and channel bandwidths.

Table 6.6.3.1.3-2: Spurious emissions limits

Frequency Range	Maximum Level	Measurement bandwidth	NOTE
9 kHz ≤ f < 150 kHz	-36 dBm	1 kHz
150 kHz ≤ f < 30 MHz	-36 dBm	10 kHz
30 MHz ≤ f < 1000 MHz	-36 dBm	100 kHz
1 GHz ≤ f < 12.75 GHz	-30 dBm	1 MHz
12.75 GHz ≤ f < 5^th harmonic of the upper frequency edge of the UL operating band in GHz	-30 dBm	1 MHz	1
12.75 GHz < f < 26GHz	-30dBm	1MHz	2
NOTE 1: Applies for Band 22, Band 42, Band 43 and Band 48. NOTE 2: Applies for Band 46 and Band 47.

The normative reference for this requirement is TS 36.101 [2] subclause 6.6.3.1.

6.6.3.1.4 Test description

6.6.3.1.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and channel bandwidths based on E-UTRA bands specified in Table 5.4.2.1-1. All of these configurations shall be tested with applicable test parameters for each channel bandwidth, and are shown in Table 6.6.3.1.4.1-1. The details of the uplink reference measurement channels (RMCs) are specified in Annexe A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.1.4.1-1: Test Configuration Table

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1)				Low range, Mid range, High range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				Lowest, 5MHz, Highest
Test Parameters for Channel Bandwidths
	Downlink Configuration			Uplink Configuration
Ch BW	Mod’n	RB allocation		Mod’n	RB allocation
		FDD	TDD		FDD	TDD
1.4MHz	N/A for Spurious Emissions testing			QPSK	6	6
1.4MHz				QPSK	1	1
3MHz				QPSK	15	15
3MHz				QPSK	1	1
5MHz				QPSK	25	25
5MHz				QPSK	1	1
10MHz				QPSK	50	50
10MHz				QPSK	1	1
15MHz				QPSK	75	75
15MHz				QPSK	1	1
20MHz				QPSK	100	100
20MHz				QPSK	1	1
Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, which applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The 1 RB allocation shall be tested at both RB #0 and RB #max.

1. Connect the SS to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure A.7.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals are initially set up according to Annex C0, C.1 and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Table 6.6.3.1.4.1-1.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.1.4.3.

6.6.3.1.4.2 Test procedure

1. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 6.6.3.1.4.1-1. Since the UE has no payload data to send, the UE transmits uplink MAC padding bits on the UL RMC.

2. Send continuously uplink power control "up" commands in the uplink scheduling information to the UE until the UE transmits at P_UMAX level.

3. Measure the power of the transmitted signal with a measurement filter of bandwidths according to table 6.6.3.1.5-1. The centre frequency of the filter shall be stepped in contiguous steps according to table 6.6.3.1.5-1. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

6.6.3.1.4.3 Message contents

Message contents are according to TS 36.508 [7] subclause 4.6.

6.6.3.1.5 Test requirement

This clause specifies the requirements for the specified E-UTRA band for Transmitter Spurious emissions requirement with frequency range as indicated in Table 6.6.3.1.5-1.

The measured average power of spurious emission, derived in step 3, shall not exceed the described value in Table 6.6.3.1.5-1.

The spurious emission limits apply for the frequency ranges that are more than Δf_OOB (MHz) from the edge of the channel bandwidth shown in Table 6.6.3.1.3-1.

Table 6.6.3.1.5-1: General spurious emissions test requirements

Frequency Range	Maximum Level	Measurement Bandwidth	Notes
9 kHz ≤ f < 150 kHz	-36 dBm	1 kHz
150 kHz ≤ f < 30 MHz	-36 dBm	10 kHz
30 MHz ≤ f < 1000 MHz	-36 dBm	100 kHz
1 GHz ≤ f < 12.75 GHz	-30 dBm	1 MHz
12.75 GHz ≤ f < 5^th harmonic of the upper frequency edge of the UL operating band in GHz	-30 dBm	1 MHz	Note 1
Note 1: Applies for Band 22, Band 42 and Band 43

6.6.3.1_1 Transmitter Spurious emissions for Multi-Cluster PUSCH

6.6.3.1_1.1 Test purpose

To verify that UE transmitter does not cause unacceptable interference to other channels or other systems in terms of transmitter spurious emissions for Multi-Cluster PUSCH transmission.

6.6.3.1_1.2 Test applicability

This test case applies to all types of E-UTRA UE release 10 and forward that support multi cluster PUSCH within a component carrier for the tested band.

6.6.3.1_1.3 Minimum conformance requirements

This clause specifies the requirements for the specified E-UTRA band for Transmitter Spurious emissions requirement with frequency range as indicated in table 6.6.3.1_1.3-2.

The spurious emission limits apply for the frequency ranges that are more than Δf_OOB (MHz) from the edge of the channel bandwidth.

Table 6.6.3.1_1.3-1: Δf_OOB boundary between E-UTRA channel and spurious emission domain

Channel bandwidth	1.4 MHz	3.0 MHz	5 MHz	10 MHz	15 MHz	20 MHz
Δf_OOB (MHz)	2.8	6	10	15	20	25

The spurious emission limits in Table 6.6.3.1_1.3-2 apply for all transmitter band configurations (RB) and channel bandwidths.

Table 6.6.3.1_1.3-2: Spurious emissions limits

Frequency Range	Maximum Level	Measurement Bandwidth	Notes
9 kHz ≤ f < 150 kHz	-36 dBm	1 kHz
150 kHz ≤ f < 30 MHz	-36 dBm	10 kHz
30 MHz ≤ f < 1000 MHz	-36 dBm	100 kHz
1 GHz ≤ f < 12.75 GHz	-30 dBm	1 MHz
12.75 GHz ≤ f < 5^th harmonic of the upper frequency edge of the UL operating band in GHz	-30 dBm	1 MHz	Note 1
Note 1: Applies for Band 22, Band 42 and Band 43

The normative reference for this requirement is TS 36.101 [2] subclause 6.6.3.1.

6.6.3.1_1.4 Test description

6.6.3.1_1.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and channel bandwidths based on E-UTRA bands specified in Table 5.4.2.1-1. All of these configurations shall be tested with applicable test parameters for each channel bandwidth, and are shown in Table 6.6.3.1_1.4.1-1. The details of the uplink reference measurement channels (RMCs) are specified in Annexe A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.1_1.4.1-1: Test Configuration Table

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1				Normal
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1				Low range, Mid range, High range
Test Channel Bandwidths as specified in TS 36.508 [7] subclause 4.3.1				Highest
Test Parameters for Channel Bandwidths
Configuration ID	Downlink Configuration		Uplink Configuration
	Ch BW	N/A for SEM testing	Mod’n		Cluster1 RB allocations (L_CRB @ RB_start)		Cluster2 RB allocations (L_CRB @ RB_start)
1	5MHz		16QAM		2@0	1@24
2	5MHz		16QAM		18@0	2@22
3	5MHz		16QAM		2@0	18@6
4	10MHz		16QAM		3@0	2@48
5	10MHz		16QAM		42@0	3@45
6	10MHz		16QAM		3@0	42@6
7	15MHz		16QAM		8@0	7@68
8	15MHz		16QAM		60@0	4@68
9	15MHz		16QAM		4@0	60@12
10	20MHz		16QAM		4@0	4@96
11	20MHz		16QAM		92@0	4@96
12	20MHz		16QAM		4@0	92@8
Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1.

1. Connect the SS to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure A.7.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals are initially set up according to Annex C0, C.1 and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Table 6.6.3.1_1.4.1-1.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.1_1.4.3.

6.6.3.1_1.4.2 Test procedure

1. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 6.6.3.1_1.4.1-1. Since the UE has no payload data to send, the UE transmits uplink MAC padding bits on the UL RMC.

2. Send continuously uplink power control "up" commands in the uplink scheduling information to the UE until the UE transmits at P_UMAX level.

3. Measure the power of the transmitted signal with a measurement filter of bandwidths according to table 6.6.3.1_1.5-1. The centre frequency of the filter shall be stepped in contiguous steps according to table 6.6.3.1_1.5-1. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

6.6.3.1_1.4.3 Message contents

Message contents are according to TS 36.508 [7] subclause 4.6.

6.6.3.1_1.5 Test requirement

This clause specifies the requirements for the specified E-UTRA band for Transmitter Spurious emissions requirement with frequency range as indicated in table 6.6.3.1_1.5-1.

The measured average power of spurious emission, derived in step 3, shall not exceed the described value in Table 6.6.3.1_1.5-1.

The spurious emission limits apply for the frequency ranges that are more than Δf_OOB (MHz) from the edge of the channel bandwidth shown in Table 6.6.3.1_1.5-1.

Table 6.6.3.1_1.5-1: General spurious emissions test requirements

Frequency Range	Maximum Level	Measurement Bandwidth	Notes
9 kHz ≤ f < 150 kHz	-36 dBm	1 kHz
150 kHz ≤ f < 30 MHz	-36 dBm	10 kHz
30 MHz ≤ f < 1000 MHz	-36 dBm	100 kHz
1 GHz ≤ f < 12.75 GHz	-30 dBm	1 MHz
12.75 GHz ≤ f < 5^th harmonic of the upper frequency edge of the UL operating band in GHz	-30 dBm	1 MHz	Note 1
Note 1: Applies for Band 22, Band 42 and Band 43

6.6.3.1A Transmitter Spurious emissions for CA

6.6.3.1A.0 Minimum conformance requirements

This clause specifies the spurious emission requirements for carrier aggregation.

NOTE 1: For measurement conditions at the edge of each frequency range, the lowest frequency of the measurement position in each frequency range should be set at the lowest boundary of the frequency range plus MBW/2. The highest frequency of the measurement position in each frequency range should be set at the highest boundary of the frequency range minus MBW/2. MBW denotes the measurement bandwidth defined for the protected band.

For inter-band carrier aggregation with one component carrier per operating band and the uplink active in two E-UTRA bands, the spurious emission requirement Table 6.6.3.1.3-2 apply for the frequency ranges that are more than F_OOB as defined in Table 6.6.3.1.3-1 away from edges of the assigned channel bandwidth on a component carrier. If for some frequency a spurious emission requirement of individual component carrier overlaps with the spectrum emission mask or channel bandwidth of another component carrier then it does not apply.

NOTE 2: For inter-band carrier aggregation with uplink assigned to two E-UTRA bands the requirements in Table 6.6.3.1.3-2 could be verified by measuring spurious emissions at the specific frequencies where second and third order intermodulation products generated by the two transmitted carriers can occur; in that case, the requirements for remaining applicable frequencies in Table 6.6.3.1.3-2 would be considered to be verified by the measurements verifying the one uplink inter-band CA spurious emission requirement.

For intra-band contiguous carrier aggregation the spurious emission limits apply for the frequency ranges that are more than FOOB (MHz) in Table 6.6.3.1A.0-1 from the edge of the aggregated channel bandwidth (Table 5.4.2A-1). For frequencies ΔfOOB greater than FOOB as specified in Table 6.6.3.1A.0-1the spurious emission requirements in Table 6.6.3.1.3-2 are applicable.

Table 6.6.3.1A.0-1: Boundary between E-UTRA out of band and spurious emission domain for intra-band contiguous carrier aggregation

CA Bandwidth Class	OOB boundary F_OOB (MHz)
A	Table 6.6.3.1.3-1
B	BW_{Channel_CA}+ 5
C	BW_{Channel_CA}+ 5

For intra-band non-contiguous carrier aggregation transmission the spurious emission requirement is defined as a composite spurious emission requirement. Composite spurious emission requirement applies to frequency ranges that are more than F_OOB away from the edges of the sub-blocks. Composite spurious emission requirement is defined as follows

a) Composite spurious emission requirement is a combination of individual sub-block spurious emission requirements.

b) In case the sub-block consist of one component carrier the sub-lock spurious emission requirement and F_OOB are defined in subclause 6.6.3.1.3.

c) If for some frequency an individual sub-block spurious emission requirement overlaps with the general spectrum emission mask or the sub-block bandwidth of another sub-block then it does not apply.

For combinations of intra-band and inter-band carrier aggregation with three uplink component carriers (up to two contiguously aggregated carriers per band), the spurious emission requirement is defined as follows. For the E-UTRA band supporting one component carrier the requirements in Table 6.6.3.1-2 apply for frequency ranges that are more than FOOB (MHz) from the edges of assigned channel bandwidth as defined in Table 6.6.3.1-1. For the E-UTRA band supporting two contiguous component carriers the requirements in Table 6.6.3.1-2 apply for frequency ranges that are more than FOOB (MHz) from the edges of assigned aggregated channel bandwidth as defined in Table 6.6.3.1A-1. If for some frequency a spurious emission requirement of a single component carrier or two contiguous component carriers overlap with the spurious emission requirement or channel bandwidth of another component carrier or two contiguously aggregated carriers then it does not apply.

The normative reference for this requirement is TS 36.101[2] clause 6.6.3.1A.

6.6.3.1A.1 Transmitter Spurious emissions for CA (intra-band contiguous DL CA and UL CA)

6.6.3.1A.1.1 Test purpose

To verify that transmitter of UE that support CA does not cause unacceptable interference to other channels or other systems in terms of transmitter spurious emissions.

6.6.3.1A.1.2 Test applicability

This test case applies to all types of E-UTRA UE release 10 and forward that support intra-band contiguous DL CA and UL CA.

6.6.3.1A.1.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.1A.0.

6.6.3.1A.1.4 Test description

6.6.3.1A.1.4.1 Initial condition

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and CC combinations based on E-UTRA CA bands specified in table 5.4.2A.1-1. All of these configurations shall be tested with applicable test parameters for each CA configuration, and are shown in table 6.6.3.1A.1.4.1-1. The details of the uplink and downlink reference measurement channels (RMCs) are specified in Annexes A.2 and A.3. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.1A.1.4.1-1: Test Configuration Table

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						Low range, High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						Lowest N_{RB_agg}, Highest N_{RB_agg} (Note 2)
Test Parameters for CA Configurations
CA Configuration / N_{RB_agg}		DL Allocation	CC MOD	UL Allocation
PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}	PCC & SCC RB allocations (L_CRB @ RB_start)
25	25		QPSK	25	P_25@0		S_0@0	–	–
25	25		QPSK	1	P_1@0		S_0@0	–	–
25	25		QPSK	1	P_1@24		S_0@0	–	–
25	25		QPSK	2	P_1@0		S_1@24	–	–
25	25		QPSK	50	P_25@0		S_25@0	–	–
25	50		QPSK	25	P_25@0		S_0@0	–	–
25	50		QPSK	1	P_1@0		S_0@0	–	–
25	50		QPSK	1	P_1@24		S_0@0	–	–
25	50		QPSK	2	P_1@0		S_1@49	–	–
25	50		QPSK	75	P_25@0		S_50@0	–	–
50	25	N/A for Spurious Emissions testing	QPSK	50	P_50@0		S_0@0	–	–
50	25		QPSK	1	P_1@0		S_0@0	–	–
50	25		QPSK	1	P_1@49		S_0@0	–	–
50	25		QPSK	2	P_1@0		S_1@24	–	–
50	25		QPSK	75	P_50@0		S_25@0	–	–
50	50		QPSK	50	P_50@0		S_0@0	–	–
50	50		QPSK	1	P_1@0		S_0@0	–	–
50	50		QPSK	1	P_1@49		S_0@0	–	–
50	50		QPSK	2	P_1@0		S_1@49	–	–
50	50		QPSK	100	P_50@0		S_50@0	–	–
75	25		QPSK	25	P_25@0		S_0@0	–	–
75	25		QPSK	1	P_1@0		S_0@0	–	–
75	25		QPSK	1	P_1@74		S_0@0	–	–
75	25		QPSK	2	P_1@0		S_1@24	–	–
75	25		QPSK	100	P_75@0		S_25@0	–	–
75	75		QPSK	75	P_75@0		S_0@0	–	–
75	75		QPSK	1	P_1@0		S_0@0	–	–
75	75		QPSK	1	P_1@74		S_0@0	–	–
75	75		QPSK	2	P_1@0		S_1@74	–	–
75	75		QPSK	150	P_75@0		S_75@0	–	–
100	25		QPSK	25	P_25@0		S_0@0	–	–
100	25		QPSK	1	P_1@0		S_0@0	–	–
100	25		QPSK	1	P_1@99		S_0@0	–	–
100	25		QPSK	2	P_1@0		S_1@24	–	–
100	25		QPSK	125	P_100@0		S_25@0	–	–
100	50		QPSK	50	P_50@0		S_0@0	–	–
100	50		QPSK	1	P_1@0		S_0@0	–	–
100	50		QPSK	1	P_1@99		S_0@0	–	–
100	50		QPSK	2	P_1@0		S_1@49	–	–
100	50		QPSK	150	P_100@0		S_50@0	–	–
100	75		QPSK	75	P_75@0		S_0@0	–	–
100	75		QPSK	1	P_1@0		S_0@0	–	–
100	75		QPSK	1	P_1@99		S_0@0	–	–
100	75		QPSK	2	P_1@0		S_1@74	–	–
100	75		QPSK	175	P_100@0		S_75@0	–	–
100	100		QPSK	100	P_100@0		S_0@0	–	–
100	100		QPSK	1	P_1@0		S_0@0	–	–
100	100		QPSK	1	P_1@99		S_0@0	–	–
100	100		QPSK	2	P_1@0		S_1@99	–	–
100	100		QPSK	200	P_100@0		S_100@0	–	–
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration, which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1 Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same N_{RB_agg}, only the combination with the highest NRB_PCC is tested.

1. Connect the SS to the UE antenna connectors as shown in TS 36.508[7] Annex A Figure group A.33 as appropriate.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals for PCC are initially set up according to Annex C.0, C.1, and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channel is set according to Table 6.6.3.1A.1.4.1-1.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.1A.1.4.3.

6.6.3.1A.1.4.2 Test procedure

1. Configure SCC according to Annex C.0, C.1 and Annex C.3.0 for all downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4. Message contents are defined in clause 6.6.3.1A.1.4.3

3. SS activates SCC by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 6.6.3.1A.1.4.1-1 on both PCC and SCC. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

5. Send continuously uplink power control “up” commands in every uplink scheduling information to the UE until the UE transmits at P_UMAX level.

6. Measure the power of the transmitted signal with a measurement filter of bandwidths according to Table 6.6.3.1A.1.5-1 for each component carrier. The centre frequency of the filter shall be stepped in contiguous steps according to Table 6.6.3.1A.1.5-1. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

6.6.3.1A.1.4.3 Message contents

Message contents are according to TS 36.508 [7] subclause 4.6. In test procedure step 2, for SCC configuration there are no additional message contents.

6.6.3.1A.1.5 Test Requirements

This clause specifies the requirements for the specified E-UTRA band for Transmitter Spurious emissions requirement with frequency range as indicated in table 6.6.3.1A.1.5-1.

For frequencies Δf_OOB greater than F_OOB as specified in Table 6.6.3.1A.0-1the measured average power of spurious emission, derived in step 6, shall not exceed the described value in Table 6.6.3.1A.1.5-1.

Table 6.6.3.1A.1.5-1: Spurious emissions limits

Frequency Range	Maximum Level	Measurement Bandwidth	Notes
9 kHz ≤ f < 150 kHz	-36 dBm	1 kHz
150 kHz ≤ f < 30 MHz	-36 dBm	10 kHz
30 MHz ≤ f < 1000 MHz	-36 dBm	100 kHz
1 GHz ≤ f < 12.75 GHz	-30 dBm	1 MHz
12.75 GHz ≤ f < 5^th harmonic of the upper frequency edge of the UL operating band in GHz	-30 dBm	1 MHz	Note 1
12.75 GHz < f < 26GHz	-30dBm	1MHz	Note 2
Note1: Applies for Band 22, Band 42, Band 43 and Band 48. Note 2: Applies for Band 46 and Band 47.

6.6.3.1A.2 Transmitter Spurious emissions for CA (inter-band DL CA and UL CA)

6.6.3.1A.2.1 Test purpose

To verify that transmitter of UE that support CA does not cause unacceptable interference to other channels or other systems in terms of transmitter spurious emissions.

6.6.3.1A.2.2 Test applicability

This test case applies to all types of E-UTRA UE release 11 and forward that support inter-band DL CA and UL CA. The requirements also apply to all types of E-UTRA UE release 14 and forward that support uplink LAA.

6.6.3.1A.2.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.1A.0.

6.6.3.1A.2.4 Test description

6.6.3.1A.2.4.1 Initial condition

Same as in clause 6.6.3.1A.1.4.1 with the following exceptions:

– Instead of Table 5.4.2A.1-1🡪 use Table 5.4.2A.1-2 for CA configurations with two bands or Table 5.4.2A.1-2a for CA configurations with three bands.

– Instead of Table 6.6.3.1A.1.4.1-1 🡪 use Table 6.6.3.1A.2.4.1-1 or Table 6.6.3.1A.2.4.1-2.

– Instead of clause 6.6.3.1A.1.4.3 use clause 6.6.3.1A.2.4.3.

Table 6.6.3.1A.2.4.1-1: Test Configuration Table

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1				NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes.				Low range for PCC and SCC High range for PCC and SCC
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.				Lowest N_{RB_agg} Highest N_{RB_agg} (Note 2)
Test Parameters for CA Configurations
CA Configuration / N_{RB_agg}		DL Allocation	CC MOD	UL Allocation
PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}	PCC & SCC RB allocations (L_CRB @ RB_start)
6	25	N/A for this test	QPSK	2	P_1@0	S_1@0	–	–
6	25		QPSK	2	P_1@5	S_1@24	–	–
6	25		QPSK	31	P_6@0	S_25@0	–	–
6	50		QPSK	2	P_1@0	S_1@0	–	–
6	50		QPSK	2	P_1@5	S_1@49	–	–
6	50		QPSK	56	P_6@0	S_50@0	–	–
25	15		QPSK	2	P_1@0	S_1@0	–	–
25	15		QPSK	2	P_1@24	S_1@14	–	–
25	15		QPSK	40	P_25@0	S_15@0	–	–
25	25		QPSK	2	P_1@0	S_1@0	–	–
25	25		QPSK	2	P_1@24	S_1@24	–	–
25	25		QPSK	50	P_25@0	S_25@0	–	–
25	50		QPSK	2	P_1@0	S_1@0	–	–
25	50		QPSK	2	P_1@24	S_1@49	–	–
25	50		QPSK	75	P_25@0	S_50@0	–	–
50	50		QPSK	2	P_1@0	S_1@0	–	–
50	50		QPSK	2	P_1@49	S_1@49	–	–
50	50		QPSK	100	P_50@0	S_50@0	–	–
50	100		QPSK	2	P_1@0	S_1@0	–	–
50	100		QPSK	2	P_1@49	S_1@99	–	–
50	100		QPSK	150	P_50@0	S_100@0	–	–
75	25		QPSK	2	P_1@0	S_1@0	–	–
75	25		QPSK	2	P_1@74	S_1@24	–	–
75	25		QPSK	100	P_75@0	S_25@0	–	–
75	75		QPSK	2	P_1@0	S_1@0	–	–
75	75		QPSK	2	P_1@74	S_1@74	–	–
75	75		QPSK	150	P_75@0	S_75@0	–	–
100	75		QPSK	2	P_1@0	S_1@0	–	–
100	75		QPSK	2	P_1@99	S_1@74	–	–
100	75		QPSK	175	P_100@0	S_75@0	–	–
100	50		QPSK	2	P_1@0	S_1@0	–	–
100	50		QPSK	2	P_1@99	S_1@49	–	–
100	50		QPSK	150	P_100@0	S_50@0	–	–
100	100		QPSK	2	P_1@0	S_1@0	–	–
100	100		QPSK	2	P_1@99	S_1@99	–	–
100	100		QPSK	200	P_100@0	S_100@0	–	–
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration, which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-2. Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same N_{RB_agg}, only the combination with the highest NRB_PCC is tested.

Table 6.6.3.1A.2.4.1-2: Test Configuration Table for UL LAA

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1				NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes.				Low range for PCC and SCC High range for PCC and SCC
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.				Lowest N_{RB_agg} Highest N_{RB_agg} (Note 2)
Test Parameters for CA Configurations
CA Configuration / N_{RB_agg}		DL Allocation	CC MOD	UL Allocation
PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}	PCC RB Allocation (L_CRB @ RBstart) SCC RB Allocations(L@ RBstart) (Note 3)
6	100	N/Afor this test	QPSK	11	P_1@0	S_1@0	–	–
6	100		QPSK	11	P_1@5	S_1@9	–	–
6	100		QPSK	106	P_6@0	S_10@0	–	–
15	100		QPSK	11	P_1@0	S_1@0	–	–
15	100		QPSK	11	P_1@14	S_1@9	–	–
15	100		QPSK	115	P_15@0	S_10@0	–	–
25	100		QPSK	11	P_1@0	S_1@0	–	–
25	100		QPSK	11	P_1@24	S_1@9	–	–
25	100		QPSK	125	P_25@0	S_10@0	–	–
50	100		QPSK	11	P_1@0	S_1@0	–	–
50	100		QPSK	11	P_1@49	S_1@9	–	–
50	100		QPSK	150	P_50@0	S_10@0	–	–
75	100		QPSK	11	P_1@0	S_1@0	–	–
75	100		QPSK	11	P_1@74	S_1@9	–	–
75	100		QPSK	175	P_75@0	S_10@0	–	–
100	100		QPSK	11	P_1@0	S_1@0	–	–
100	100		QPSK	11	P_1@99	S_1@9	–	–
100	100		QPSK	200	P_100@0	S_10@0	–	–
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration, which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-2. Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same N_{RB_agg}, only the combination with the highest NRB_PCC is tested. Note 3: For eLAA SCC, the RBstart and L are defined in TS 36.213[10] clause 8.1.4.

6.6.3.1A.2.4.2 Test procedure

1. Configure SCC according to Annex C.0, C.1 and Annex C.3.0 for all downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4. Message contents are defined in clause 6.6.3.1A.2.4.3

3. SS activates SCC by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 (or DCI format 0A for SCC in the case of uplink LAA) for C_RNTI to schedule the UL RMC according to Table 6.6.3.1A.2.4.1-1 (or Table 6.6.3.1A.2.4.1-2 for SCC in the case of uplink LAA) on both PCC and SCC. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

5. Send continuously uplink power control “up” commands in every uplink scheduling information to the UE until the UE transmits at P_UMAX level.

6. Measure the power of the transmitted signal with a measurement filter of bandwidths according to Table 6.6.3.1A.2.5-1 for each component carrier. The centre frequency of the filter shall be stepped in contiguous steps according to Table 6.6.3.1A.2.5-1. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

6.6.3.1A.2.4.3 Message contents

Message contents are according to TS 36.508 [7] clause 4.6 with exceptions as in clause 6.6.3.1A.1.4.3.

For SCC in the case of uplink LAA, message contents are according to TS 36.508[7] subclause4.6 with the following exceptions specified in Tables 6.6.3.1A.1.2.4.3-1 and 6.6.3.1A.1.2.4.3-2.

Table 6.6.3.1A.1.2.4.3-1 LogicalChannelConfig-DRB (Initial Condition, step 14, Table 4.5.2.3-1)

Derivation Path: 36.508 Table 4.8.2.1.4-1
Information Element	Value/remark	Comment	Condition
LogicalChannelConfig-DRB ::= SEQUENCE {
ul-SpecificParameters SEQUENCE {
laa-UL-Allowed-r14	true
}
}

Table 6.6.3.1A.1.2.4.3-2 PhysicalConfigDedicatedSCell (Step 2, test procedure)

Derivation Path: 36.508 Table 4.6.3-6A
Information Element	Value/remark	Comment	Condition
PhysicalConfigDedicatedSCell-r10-DEFAULT ::= SEQUENCE {
laa-SCellConfiguration-v1430 ::= SEQUENCE {
	NULL
}
}

6.6.3.1A.2.5 Test requirement

This clause specifies the requirements for the specified E-UTRA band for Transmitter Spurious emissions requirement with frequency range as indicated in table 6.6.3.1A.2.5-1.

Table 6.6.3.1A.2.5-1: Spurious emissions limits

Frequency Range	Maximum Level	Measurement Bandwidth	Notes
Test requirements for CA_1A-3A Configuration
135 MHz  f  270 MHz	-36 dBm	100 kHz
1440 MHz f  1650 MHz 2055 MHz  f  2250 MHz 3630 MHz  f  3765 MHz 5340 MHz  f  5745 MHz	-30 dBm	1 MHz
Test requirements for CA_1A-5A Configuration
222 MHz  f  332 MHz	-36 dBm	100 kHz
1071 MHz f  1156 MHz 2744 MHz  f  2829 MHz 2991 MHz  f  3136 MHz 3568 MHz  f  3678 MHz 4664 MHz  f  4809 MHz	-30 dBm	1 MHz
Test requirements for CA_1A-7A Configuration
520 MHz  f  650 MHz	-36 dBm	100 kHz
1270 MHz f  1460 MHz 3020 MHz  f  3220 MHz 4420 MHz  f  4550 MHz 6340 MHz  f  6530 MHz 6920 MHz  f  7120 MHz	-30 dBm	1 MHz
Test requirements for CA_1A-8A Configuration
90 MHz  f  220 MHz	-36 dBm	100 kHz
1005 MHz f  1100 MHz 2800 MHz  f  2895 MHz 2925 MHz  f  3080 MHz 3680 MHz  f  3810 MHz 4720 MHz  f  4875 MHz	-30 dBm	1 MHz
Test requirements for CA_1A-18A Configuration
260 MHz  f  350 MHz	-36 dBm	100 kHz
1090 MHz  f  1165 MHz 2735 MHz  f  2810 MHz 3010 MHz  f  3145 MHz 3550 MHz  f  3640 MHz 4655 MHz  f  4790 MHz	-30 dBm	1 MHz
Test requirements for CA_1A-19A Configuration
230 MHz  f  320 MHz	-36 dBm	100 kHz
1075 MHz f  1150 MHz 2750 MHz  f  2825 MHz 2995 MHz  f  3130 MHz 3580 MHz  f  3670 MHz 4670 MHz  f  4805 MHz	-30 dBm	1 MHz
Test requirements for CA_1A-21A Configuration
457.1 MHz  f  532.1 MHz 915.8 MHz  f < 1000 MHz	-36 dBm	100 kHz
1000 MHz f  1005.8 MHz 2377.1 MHz  f  2512.1 MHz 3367.9 MHz  f  3442.9 MHz 4515.8 MHz  f  4905.8 MHz 5287.9 MHz  f  5422.9 MHz	-30 dBm	1 MHz
Test requirements for CA_1A-26A Configuration
222 MHz  f  352 MHz	-36 dBm	100 kHz
1071 MHz f  1166 MHz 2734 MHz  f  2829 MHz 2991 MHz  f  3146 MHz 3548 MHz  f  3678 MHz 4654 MHz  f  4809 MHz	-30 dBm	1 MHz
Test requirements for CA_1A-28A Configuration
424 MHz  f  574 MHz	-36 dBm	100 kHz
1172 MHz f  1277 MHz 2623 MHz  f  2728 MHz 3092 MHz  f  3257 MHz 3326 MHz  f  3476 MHz 4543 MHz  f  4708 MHz	-30 dBm	1 MHz
Test requirements for CA_1A-42A Configuration
240 MHz  f  560 MHz	-36 dBm	100 kHz
1420 MHz f  1680 MHz 4820 MHz  f  5280 MHz 5320 MHz  f  5580 MHz 7240 MHz  f  7560 MHz 8720 MHz  f  9180 MHz	-30 dBm	1 MHz
Test requirements for CA_2A-4A Configuration
95 MHz  f  200 MHz	-36 dBm	100 kHz
1510 MHz f  1660 MHz 1945 MHz  f  2110 MHz 3560 MHz  f  3665 MHz 5270 MHz  f  5575 MHz	-30 dBm	1 MHz
Test requirements for CA_2A-5A Configuration
152 MHz  f  262 MHz	-36 dBm	100 kHz
1001 MHz f  1086 MHz 2674 MHz  f  2759 MHz 2851 MHz  f  2996 MHz 3498 MHz  f  3608 MHz 4524 MHz  f  4669 MHz	-30 dBm	1 MHz
Test requirements for CA_2A-7A Configuration
590 MHz  f  720 MHz	-36 dBm	100 kHz
1130 MHz f  1320 MHz 3090 MHz  f  3290 MHz 4350 MHz  f  4480 MHz 6200 MHz  f  6390 MHz 6850 MHz  f  7050 MHz	-30 dBm	1 MHz
Test requirements for CA_2A-12A Configuration
418 MHz  f  512 MHz	-36 dBm	100 kHz
1134 MHz f  1211 MHz 2549 MHz  f  2626 MHz 2984 MHz  f  3121 MHz 3248 MHz  f  3342 MHz 4399 MHz  f  4536 MHz	-30 dBm	1 MHz
Test requirements for CA_2A-13A Configuration
276 MHz  f  356 MHz	-36 dBm	100 kHz
1063 MHz f  1133 MHz 2627 MHz  f  2697 MHz 2913 MHz  f  3043 MHz 3404 MHz  f  3484 MHz 4477 MHz  f  4607 MHz	-30 dBm	1 MHz
Test requirements for CA_2A-30A Configuration
395 MHz  f  465 MHz	-36 dBm	100 kHz
1385 MHz f  1515 MHz 2700 MHz  f  2780 MHz 4155 MHz  f  4225 MHz 6005 MHz  f  6135 MHz 6460 MHz  f  6540 MHz	-30 dBm	1 MHz
Test requirements for CA_2A-46A Configuration
1330 MHz ≤ f ≤ 2225 MHz 3240 MHz ≤ f ≤ 4075 MHz 7000 MHz ≤ f ≤ 7835 MHz 8390 MHz ≤ f ≤ 10000 MHz 12150 MHz ≤ f ≤ 13760 MHz	-30 dBm	1 MHz
Test requirements for CA_2A-66A Configuration
70 MHz  f  200 MHz	-36 dBm	100 kHz
1510 MHz f  1710 MHz 1920 MHz  f  2110 MHz 3560 MHz  f  3690 MHz 5270 MHz  f  5600 MHz	-30 dBm	1 MHz
Test requirements for CA_3A-5A Configuration
12 MHz  f < 30 MHz	-36 dBm	10 kHz
30 MHz  f  137 MHz 861 MHz  f  961 MHz	-36 dBm	100 kHz
2534 MHz f  2746 MHz 3358 MHz  f  3483 MHz 4244 MHz  f  4419 MHz	-30 dBm	1 MHz
Test requirements for CA_3A-7A Configuration
715 MHz  f < 1000 MHz	-36 dBm	100 kHz
1000 MHz f  1070 MHz 3215 MHz  f  3430 MHz 4210 MHz  f  4355 MHz 5920 MHz  f  6140 MHz 6710 MHz  f  6925 MHz	-30 dBm	1 MHz
Test requirements for CA_3A-8A Configuration
25 MHz  f < 30 MHz	-36 dBm	10 kHz
30 MHz  f  120 MHz 795 MHz  f  905 MHz	-36 dBm	100 kHz
2505 MHz f  2700 MHz 3470 MHz  f  3615 MHz 4300 MHz  f  4485 MHz	-30 dBm	1 MHz
Test requirements for CA_3A-18A Configuration
50 MHz  f  155 MHz 880 MHz  f  970 MHz	-36 dBm	100 kHz
2525 MHz  f  2755 MHz 3340 MHz  f  3445 MHz 4235 MHz  f  4400 MHz	-30 dBm	1 MHz
Test requirements for CA_3A-19A Configuration
20 MHz  f < 30 MHz	-36 dBm	10 kHz
30 MHz  f  125 MHz 865 MHz  f  955 MHz	-36 dBm	100 kHz
2540 MHz f  2740 MHz 3370 MHz  f  3475 MHz 4250 MHz  f  4415 MHz	-30 dBm	1 MHz
Test requirements for CA_3A-20A Configuration
9 kHz  f < 150 kHz	-36 dBm	1 kHz
150 kHz  f < 30 MHz	-36 dBm	10 kHz
30 MHz  f  121 MHz 848 MHz  f  953 MHz	-36 dBm	100 kHz
2542 MHz f  2738 MHz 3374 MHz  f  3509 MHz 4252 MHz  f  4432 MHz	-30 dBm	1 MHz
Test requirements for CA_3A-26A Configuration
12 MHz  f < 30 MHz	-36 dBm	10 kHz
30 MHz  f  157 MHz	-36 dBm	100 kHz
861 MHz f  971 MHz	-36 dBm	100 kHz
2524 MHz f  2756 MHz 3338 MHz  f  3483 MHz 4234 MHz  f  4419 MHz	-30 dBm	1 MHz
Test requirements for CA_3A-28A Configuration
214 MHz  f  379 MHz 962 MHz  f  1000 MHz	-36 dBm	100 kHz
1000 MHz  f 1082 MHz 2413 MHz  f  2533 MHz 2672 MHz  f  2867 MHz 3116 MHz  f  3281 MHz 4123 MHz  f  4318 MHz	-30 dBm	1 MHz
Test requirements for CA_3A-41A Configuration
711 MHz f < 1000 MHz	-36 dBm	100 kHz
1000 MHz f 1074 MHz 3207 MHz f 3670 MHz 4206 MHz f 4475 MHz 5916 MHz f 6260 MHz 6702 MHz f 7165 MHz	-30 dBm	1 MHz
Test requirements for CA_3A-42A Configuration
170 MHz f 180 MHz	-36 dBm	100 kHz
1615 MHz f 1890 MHz 5015 MHz f 5490 MHz 6820 MHz f 7170 MHz 8510 MHz f 8985 MHz	-30 dBm	1 MHz
Test requirements for CA_4A-5A Configuration
12 MHz  f < 30 MHz	-36 dBm	10 kHz
30 MHz  f  107 MHz 861 MHz  f  931 MHz	-36 dBm	100 kHz
2534 MHz f  2686 MHz 3358 MHz  f  3453 MHz 4244 MHz  f  4359 MHz	-30 dBm	1 MHz
Test requirements for CA_4A-7A Configuration
745 MHz  f 1000 MHz	-36 dBm	100 kHz
1000 MHz  f 1010 MHz 3245 MHz  f  3430 MHz 4210 MHz  f  4325 MHz 5920 MHz  f  6080 MHz 6710 MHz  f  6895 MHz	-30 dBm	1 MHz
Test requirements for CA_4A-12A Configuration
278 MHz  f  357 MHz 994 MHz  f < 1000 MHz	-36 dBm	100 kHz
1000 MHz f  1056 MHz 2409 MHz  f  2471 MHz 2704 MHz  f  2811 MHz 3108 MHz  f  3187 MHz 4119 MHz  f  4226 MHz	-30 dBm	1 MHz
Test requirements for CA_4A-13A Configuration
136 MHz  f  201 MHz 923 MHz  f  978 MHz	-36 dBm	100 kHz
2487 MHz f  2542 MHz 2633 MHz  f  2733 MHz 3264 MHz  f  3329 MHz 4197 MHz  f  4297 MHz	-30 dBm	1 MHz
Test requirements for CA_4A-17A Configuration
278 MHz  f  347 MHz 994 MHz  f < 1000 MHz	-36 dBm	100 kHz
1000 MHz f  1056 MHz 2414 MHz  f  2471 MHz 2704 MHz  f  2806 MHz 3118 MHz  f  3187 MHz 4124 MHz  f  4226 MHz	-30 dBm	1 MHz
Test requirements for CA_5A-7A Configuration
802 MHz  f  922 MHz	-36 dBm	100 kHz
1651 MHz f  1746 MHz 3324 MHz  f  3419 MHz 4148 MHz  f  4316 MHz 5824 MHz  f 5989 MHz	-30 dBm	1 MHz
Test requirements for CA_5A-12A Configuration
108 MHz ≤ f ≤ 150 MHz 549 MHz ≤ f ≤ 608 MHz 932 MHz ≤ f ≤ 999 MHz	-36 dBm	100 kHz
1523 MHz ≤ f ≤ 1565 MHz 2222 MHz ≤ f ≤ 2281 MHz 2347 MHz ≤ f ≤ 2414 MHz	-30 dBm	1 MHz
Test requirements for CA_5A-17A Configuration
108 MHzf  145 MHz 559 MHz  f  608 MHz 932 MHz f  99e4 MHz	-36 dBm	100 kHz
1528 MHzf  1565 MHz 2232 MHz  f  2281 MHz 2352 MHz f  2414 MHz	-30 dBm	1 MHz
Test requirements for CA_5A-30A Configuration
607 MHz  f  667 MHz	-36 dBm	100 kHz
1456 MHz f  1491 MHz 3129 MHz  f  3164 MHz 3761 MHz  f  3806 MHz 3953 MHz  f  4013 MHz 5434 MHz  f 5479 MHz	-30 dBm	1 MHz
Test requirements for CA_5A-66A Configuration
12 MHz  f < 30 MHz	-36 dBm	10 kHz
30 MHz  f  132 MHz 861 MHz  f  956 MHz	-36 dBm	100 kHz
2534 MHz f  2736 MHz 3358 MHz  f  3478 MHz 4244 MHz  f 4409 MHz	-30 dBm	1 MHz
Test requirements for CA_7A-20A Configuration
776 MHz  f  906 MHz	-36 dBm	100 kHz
1638 MHz f  1738 MHz 3332 MHz  f  3432 MHz 4138 MHz  f  4308 MHz 5832 MHz  f 6002 MHz	-30 dBm	1 MHz
Test requirements for CA_7A-28A Configuration
1004 MHz f  1164 MHz 1752 MHz  f  1867 MHz 3203 MHz  f  3318 MHz 3906 MHz  f  4066 MHz 4252 MHz  f  4437 MHz 5703 MHz  f  5888 MHz	-30 dBm	1 MHz
Test requirements for CA_11A-18A Configuration
182.1 MHz  f  232.1 MHz 597.9 MHz  f  632.9 MHz	-36 dBm	100 kHz
2025.8 MHz  f  2080.8 MHz 2242.9 MHz  f  2277.9 MHz 3057.9 MHz  f  3107.9 MHz 3670.8 MHz  f  3725.8 MHz	-30 dBm	1 MHz
Test requirements for CA_12A-30A Configuration
873 MHz  f  917 MHz	-36 dBm	100 kHz
1589 MHz f  1616 MHz 3004 MHz  f  3031 MHz 3703 MHz  f  3747 MHz 3894 MHz  f  3931 MHz 5009 MHz  f 5046 MHz	-30 dBm	1 MHz
Test requirements for CA_18A-28A Configuration
82 MHz f  127 MHz 576 MHz  f  651 MHz 897 MHz  f  957 MHz	-36 dBm	100 kHz
1518 MHz f  1563 MHz 2221 MHz  f  2296 MHz 2333 MHz  f  2393 MHz	-30 dBm	1 MHz
Test requirements for CA_19A-21A Configuration
197.1 MHz  f  242.1 MHz 602.9 MHz  f  632.9 MHz	-36 dBm	100 kHz
2050.8 MHz f  2095.8 MHz 2277.9 MHz  f  2307.9 MHz 3107.9 MHz  f  3152.9 MHz 3725.8 MHz  f  3770.8 MHz	-30 dBm	1 MHz
Test requirements for CA_26A-46A Configuration
3542 MHz ≤ f ≤ 4297 MHz 4301 MHz ≤ f ≤ 5111 MHz 5964 MHz ≤ f ≤ 6774 MHz 6778 MHz ≤ f ≤ 7623 MHz 9541 MHz ≤ f ≤ 11036 MHz 11114 MHz ≤ f ≤ 12699 MHz	-30 dBm	1 MHz
Test requirements for CA_39A-41A Configuration
576 MHz  f  810 MHz	-36 dBm	100 kHz
1070 MHz f  1344 MHz 3072 MHz  f  3500 MHz 4376 MHz  f  4610 MHz 6256 MHz  f  6530 MHz 6872 MHz  f  7300 MHz	-30 dBm	1 MHz
Test requirements for CA_41A-42A Configuration
710 MHz  f < 1000 MHz	-36 dBm	100 kHz
1000 MHz f  1104 MHz 1392 MHz  f  1980 MHz 4110 MHz  f  4704 MHz 5896 MHz  f  6290 MHz 8392 MHz  f  8980 MHz 9296 MHz  f  9890 MHz	-30 dBm	1 MHz

6.6.3.1A.3 Transmitter Spurious emissions for CA (intra-band non-contiguous DL CA and UL CA)

6.6.3.1A.3.1 Test purpose

To verify that transmitter of UE that support CA does not cause unacceptable interference to other channels or other systems in terms of transmitter spurious emissions.

6.6.3.1A.3.2 Test applicability

This test case applies to all types of E-UTRA UE release 11 and forward that support intra-band non-contiguous DL CA and UL CA.

6.6.3.1A.3.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.1A.0.

6.6.3.1A.3.4 Test description

6.6.3.1A.3.4.1 Initial condition

Same as in clause 6.6.3.1A.1.4.1 with the following exceptions:

– Instead of Table 5.4.2A.1-1🡪 use Table 5.4.2A.1-3 for CA configurations.

– Instead of Table 6.6.3.1A.1.4.1-1 🡪 use Table 6.6.3.1A.3.4.1-1.

– Instead of clause 6.6.3.1A.1.4.3 🡪 use clause 6.6.3.1A.3.4.3.

Table 6.6.3.1A.3.4.1-1: Test Configuration Table

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1					Normal
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.					Refer to test points A: N/A (Range is not relevant), Maximum Wgap
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.					Refer to test point Test only test points with Lowest N_RB for PCC and SCC Highest N_RB for PCC and SCC
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		W_gap[MHz]	DL Allocation		UL Allocation
	PCC N_RB	SCCs N_RB	W_gap[MHz]	CC MOD	PCC & SCC RB allocation	CC MOD	PCC N_{RB_alloc} (L_CRB @ RB_start)	CC MOD	SCC N_{RB_alloc} (L_CRB @ RB_start)
Test Parameters for CA_4A-4A Configurations
1	25	25	35	N/A		QPSK	P_1@0	QPSK	S_1@0
2	25	25	35			QPSK	P_1@24	QPSK	S_1@24
3	25	25	35			QPSK	P_25@0	QPSK	S_25@0
4	50	50	25			QPSK	P_1@0	QPSK	S_1@0
5	50	50	25			QPSK	P_1@49	QPSK	S_1@49
6	50	50	25			QPSK	P_50@0	QPSK	S_50@0
7	100	100	5			QPSK	P_1@0	QPSK	S_1@0
8	100	100	5			QPSK	P_1@99	QPSK	S_1@99
9	100	100	5			QPSK	P_100@0	QPSK	S_100@0
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration, which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-3. Note 2: The measurements need to be executed for in-gap interferer positions when the sub-block gap size W_gap allows.

6.6.3.1A.3.4.2 Test procedure

1. Configure SCC according to Annex C.0, C.1 and Annex C.3.0 for all downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4. Message contents are defined in clause 6.6.3.1A.3.4.3

3. SS activates SCC by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 6.6.3.1A.3.4.1-1 on both PCC and SCC. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

5. Send continuously uplink power control “up” commands in every uplink scheduling information to the UE until the UE transmits at P_UMAX level.

6. Measure the power of the transmitted signal with a measurement filter of bandwidths according to Table 6.6.3.1A.3.5-1 for each component carrier. The centre frequency of the filter shall be stepped in contiguous steps according to Table 6.6.3.1A.3.5-1. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

7. Repeat the measurement for in-gap interferer positions when the sub-block gap size W_gap allows.

6.6.3.1A.3.4.3 Message contents

Message contents are according to TS 36.508 [7] subclause 4.6. In test procedure step 2, for SCC configuration there are no additional message contents.

6.6.3.1A.3.5 Test Requirements

This clause specifies the requirements for the specified E-UTRA band for Transmitter Spurious emissions requirement with frequency range as indicated in table 6.6.3.1A.3.5-1.

Table 6.6.3.1A.3.5-1: Spurious emissions limits

Frequency Range	Maximum Level	Measurement Bandwidth	Notes
9 kHz ≤ f < 150 kHz	-36 dBm	1 kHz
150 kHz ≤ f < 30 MHz	-36 dBm	10 kHz
30 MHz ≤ f < 1000 MHz	-36 dBm	100 kHz
1 GHz ≤ f < 12.75 GHz	-30 dBm	1 MHz

6.6.3.1A.4 Transmitter Spurious emissions for CA (3UL CA)

6.6.3.1A.4.1 Transmitter Spurious emissions for CA (intra-band contiguous 3DL CA and 3UL CA)

6.6.3.1A.4.1.1 Test purpose

To verify that transmitter of UE that support CA does not cause unacceptable interference to other channels or other systems in terms of transmitter spurious emissions.

6.6.3.1A.4.1.2 Test applicability

This test case applies to all types of E-UTRA UE release 13 and forward that support intra-band contiguous 3DL CA and 3UL CA.

6.6.3.1A.4.1.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.1A.0.

6.6.3.1A.4.1.4 Test description

6.6.3.1A.4.1.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and CC combinations based on E‑UTRA CA configurations specified in table 5.4.2A.1-1. All of these configurations shall be tested with applicable test parameters for each CA Configuration, and are shown in table 6.6.3.1A.4.1.4.1-1. The details of the uplink and downlink reference measurement channels (RMCs) are specified in Annexe A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.1A.4.1.4.1-1: Test Configuration Table

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1							NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.							Low range, High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration							Lowest N_{RB_agg}, Highest N_{RB_agg} (Note 2)
Test Parameters for CA Configurations
CA Configuration / N_{RB_agg}			DL Allocation	CC MOD	UL Allocation
PCC N_RB	SCC1 N_RB	SCC2 N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}	PCC & SCC RB allocations (L_CRB @ RB_start)
50	100	100	N/A for this test	QPSK	1	P_1@0		S_0@0	S_0@0	–
50	100	100		QPSK	1	P_1@49		S_0@0	S_0@0	–
50	100	100		QPSK	250	P_50@0		S_100@0	S_100@0	–
75	100	100		QPSK	1	P_1@0		S_0@0	S_0@0	–
75	100	100		QPSK	1	P_1@74		S_0@0	S_0@0	–
75	100	100		QPSK	275	P_75@0		S_100@0	S_100@0	–
100	100	100		QPSK	1	P_1@0		S_0@0	S_0@0	–
100	100	100		QPSK	1	P_1@99		S_0@0	S_0@0	–
100	100	100		QPSK	300	P_100@0		S_100@0	S_100@0	–
100	50	100		QPSK	1	P_1@0		S_0@0	S_0@0	–
100	50	100		QPSK	1	P_1@99		S_0@0	S_0@0	–
100	50	100		QPSK	250	P_100@0		S_50@0	S_100@0	–
100	75	100		QPSK	1	P_1@0		S_0@0	S_0@0	–
100	75	100		QPSK	1	P_1@99		S_0@0	S_0@0	–
100	75	100		QPSK	275	P_100@0		S_75@0	S_100@0	–
100	100	50		QPSK	1	P_1@0		S_0@0	S_0@0	–
100	100	50		QPSK	1	P_1@99		S_0@0	S_0@0	–
100	100	50		QPSK	250	P_100@0		S_100@0	S_50@0	–
100	100	75		QPSK	1	P_1@0		S_0@0	S_0@0	–
100	100	75		QPSK	1	P_1@99		S_0@0	S_0@0	–
100	100	75		QPSK	275	P_100@0		S_100@0	S_75@0	–
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration, which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1 Note 2: If in the CA Configuration UE supports multiple CC Combinations with the same N_{RB_agg}, only the first of those is tested, according to the order on the Test Configuration Table list.

1. Connect the SS to the UE antenna connectors as shown in TS 36.508 [7] Annex A Figure group A.32 as appropriate.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals for PCC are initially set up according to Annex C.0, C.1, and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channel is set according to Table 6.6.3.1A.4.1.4.1-1.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.1A.4.1.4.3.

6.6.3.1A.4.1.4.2 Test procedure

1. Configure SCCs according to Annex C.0, C.1 and Annex C.3.0 for all downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4.

3. SS activates SCCs by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 6.6.3.1A.1.4.1-1 on all PCC and SCCs. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

5. Send continuously uplink power control “up” commands in every uplink scheduling information to the UE until the UE transmits at P_UMAX level.

6.6.3.1A.4.1.4.3 Message contents

Message contents are according to TS 36.508 [7] subclause 4.6.

6.6.3.1A.4.1.5 Test Requirements

This clause specifies the requirements for the specified E-UTRA band for Transmitter Spurious emissions requirement with frequency range as indicated in table 6.6.3.1A.4.1.5-1.

Table 6.6.3.1A.4.1.5-1: Spurious emissions limits

Frequency Range	Maximum Level	Measurement Bandwidth	Notes
9 kHz ≤ f < 150 kHz	-36 dBm	1 kHz
150 kHz ≤ f < 30 MHz	-36 dBm	10 kHz
30 MHz ≤ f < 1000 MHz	-36 dBm	100 kHz
1 GHz ≤ f < 12.75 GHz	-30 dBm	1 MHz
12.75 GHz ≤ f < 5^th harmonic of the upper frequency edge of the UL operating band in GHz	-30 dBm	1 MHz	Note 1
Note1: Applicability of this test requirement is FFS.

6.6.3.1A.4.2 Transmitter Spurious emissions for CA (inter-band 3DL CA and 3UL CA)

6.6.3.1A.4.2.1 Test purpose

Same as in clause 6.6.3.1A.4.1.1.

6.6.3.1A.4.2.2 Test applicability

This test case applies to all types of E-UTRA UE release 13 and forward that support inter-band 3DL CA and 3UL CA.

6.6.3.1A.4.2.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.1A.0.

6.6.3.1A.4.2.4 Test description

6.6.3.1A.4.2.4.1 Initial conditions

Same as in clause 6.6.3.1A.4.1.4.1 with the following exceptions:

– Instead of Table 5.4.2A.1-1🡪 use Table 5.4.2A.1-2 for CA configurations with two bands or Table 5.4.2A.1-2a for CA configurations with three bands.

– Instead of Table 6.6.3.1A.4.1.4.1-1 🡪 use Table 6.6.3.1A.4.2.4.1-1.

– Instead of clause 6.6.3.1A.4.1.4.3 use clause 6.6.3.1A.4.2.4.3.

Table 6.6.3.1A.4.2.4.1-1: Test Configuration Table

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1					NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes.					Low range for PCC and SCC High range for PCC and SCC
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.					Lowest N_{RB_agg} Highest N_{RB_agg} (Note 2)
Test Parameters for CA Configurations
CA Configuration / N_{RB_agg}			DL Allocation	CC MOD	UL Allocation
PCC N_RB	SCC1 N_RB	SCC2 N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}	PCC & SCC RB allocations (L_CRB @ RB_start)
25	100	100	N/Afor this test	QPSK	3	P_1@0	S_1@0	S_1@0	–
25	100	100		QPSK	3	P_1@0	S_1@99	S_1@99	–
25	100	100		QPSK	225	P_25@0	S_100@0	S_100@0	–
50	100	100		QPSK	3	P_1@0	S_1@0	S_1@0	–
50	100	100		QPSK	3	P_1@0	S_1@99	S_1@99	–
50	100	100		QPSK	250	P_50@0	S_100@0	S_100@0	–
75	100	100		QPSK	3	P_1@0	S_1@0	S_1@0	–
75	100	100		QPSK	3	P_1@0	S_1@99	S_1@99	–
75	100	100		QPSK	275	P_75@0	S_100@0	S_100@0	–
100	100	100		QPSK	3	P_1@0	S_1@0	S_1@0	–
100	100	100		QPSK	3	P_1@0	S_1@99	S_1@99	–
100	100	100		QPSK	300	P_100@0	S_100@0	S_100@0	–
100	25	100		QPSK	3	P_1@0	S_1@0	S_1@0	–
100	25	100		QPSK	3	P_1@0	S_1@5	S_1@99	–
100	25	100		QPSK	225	P_100@0	S_25@0	S_100@0	–
100	50	100		QPSK	3	P_1@0	S_1@0	S_1@0	–
100	50	100		QPSK	3	P_1@0	S_1@49	S_1@99	–
100	50	100		QPSK	200	P_100@0	S_50@0	S_100@0	–
100	75	100		QPSK	3	P_1@0	S_1@0	S_1@0	–
100	75	100		QPSK	3	P_1@0	S_1@74	S_1@99	–
100	75	100		QPSK	275	P_100@0	S_75@0	S_100@0	–
50	50	100		QPSK	3	P_1@0	S_1@0	S_1@0	–
50	50	100		QPSK	3	P_1@0	S_1@49	S_1@99	–
50	50	100		QPSK	200	P_50@0	S_50@0	S_100@0	–
50	75	100		QPSK	3	P_1@0	S_1@0	S_1@0	–
50	75	100		QPSK	3	P_1@0	S_1@74	S_1@99	–
50	75	100		QPSK	225	P_50@0	S_75@0	S_100@0	–
75	50	100		QPSK	3	P_1@0	S_1@0	S_1@0	–
75	50	100		QPSK	3	P_1@0	S_1@49	S_1@99	–
75	50	100		QPSK	225	P_75@0	S_50@0	S_100@0	–
75	75	100		QPSK	3	P_1@0	S_1@0	S_1@0	–
75	75	100		QPSK	3	P_1@0	S_1@74	S_1@99	–
75	75	100		QPSK	250	P_75@0	S_75@0	S_100@0	–
50	100	50		QPSK	3	P_1@0	S_1@0	S_1@0	–
50	100	50		QPSK	3	P_1@0	S_1@99	S_1@49	–
50	100	50		QPSK	200	P_50@0	S_100@0	S_50@0	–
50	100	75		QPSK	3	P_1@0	S_1@0	S_1@0	–
50	100	75		QPSK	3	P_1@0	S_1@99	S_1@74	–
50	100	75		QPSK	225	P_50@0	S_100@0	S_75@0	–
75	100	50		QPSK	3	P_1@0	S_1@0	S_1@0	–
75	100	50		QPSK	3	P_1@0	S_1@99	S_1@49	–
75	100	50		QPSK	225	P_75@0	S_100@0	S_50@0	–
75	100	75		QPSK	3	P_1@0	S_1@0	S_1@0	–
75	100	75		QPSK	3	P_1@0	S_1@99	S_1@74	–
75	100	75		QPSK	250	P_75@0	S_100@0	S_75@0	–
75	75	50		QPSK	3	P_1@0	S_1@0	S_1@0	–
75	75	50		QPSK	3	P_1@0	S_1@74	S_1@49	–
75	75	50		QPSK	200	P_75@0	S_75@0	S_50@0	–
75	75	75		QPSK	3	P_1@0	S_1@0	S_1@0	–
75	75	75		QPSK	3	P_1@0	S_1@74	S_1@74	–
75	75	75		QPSK	225	P_75@0	S_75@0	S_75@0	–
100	50	50		QPSK	3	P_1@0	S_1@0	S_1@0	–
100	50	50		QPSK	3	P_1@0	S_1@49	S_1@49	–
100	50	50		QPSK	200	P_100@0	S_50@0	S_50@0	–
100	50	75		QPSK	3	P_1@0	S_1@0	S_1@0	–
100	50	75		QPSK	3	P_1@0	S_1@49	S_1@74	–
100	50	75		QPSK	225	P_100@0	S_50@0	S_75@0	–
100	75	50		QPSK	3	P_1@0	S_1@0	S_1@0	–
100	75	50		QPSK	3	P_1@0	S_1@74	S_1@49	–
100	75	50		QPSK	225	P_100@0	S_75@0	S_50@0	–
100	75	75		QPSK	3	P_1@0	S_1@0	S_1@0	–
100	75	75		QPSK	3	P_1@0	S_1@74	S_1@74	–
100	75	75		QPSK	250	P_100@0	S_75@0	S_75@0	–
100	100	50		QPSK	3	P_1@0	S_1@0	S_1@0	–
100	100	50		QPSK	3	P_1@0	S_1@99	S_1@49	–
100	100	50		QPSK	250	P_100@0	S_100@0	S_50@0	–
100	100	75		QPSK	3	P_1@0	S_1@0	S_1@0	–
100	100	75		QPSK	3	P_1@0	S_1@99	S_1@74	–
100	100	75		QPSK	275	P_100@0	S_100@0	S_75@0	–
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration, which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-2. Note 2: If in the CA Configuration UE supports multiple CC Combinations with the same N_{RB_agg}, only the first of those is tested, according to the order on the Test Configuration Table list.

6.6.3.1A.4.2.4.2 Test procedure

Same test procedure as in clause 6.6.3.1A.4.1.4.2.

– Instead of Table 6.6.3.1A.4.1.4.1-1🡪 use Table 6.6.3.1A.4.2.4.1-1.

– Instead of Table 6.6.3.1A.4.1.5-1 🡪 use Table 6.6.3.1A.4.2.5-1.

– Instead of clause 6.6.3.1A.4.1.4.3 use clause 6.6.3.1A.4.2.4.3.

6.6.3.1A.4.2.4.3 Message contents

Message contents are according to TS 36.508 [7] subclause 4.6.

6.6.3.1A.4.2.5 Test Requirements

This clause specifies the requirements for the specified E-UTRA band for Transmitter Spurious emissions requirement with frequency range as indicated in table 6.6.3.1A.4.2.5-1.

Table 6.6.3.1A.4.2.5-1: Spurious emissions limits

Frequency Range	Maximum Level	Measurement Bandwidth	Notes
9 kHz ≤ f < 150 kHz	-36 dBm	1 kHz
150 kHz ≤ f < 30 MHz	-36 dBm	10 kHz
30 MHz ≤ f < 1000 MHz	-36 dBm	100 kHz
1 GHz ≤ f < 12.75 GHz	-30 dBm	1 MHz
12.75 GHz ≤ f < 5^th harmonic of the upper frequency edge of the UL operating band in GHz	-30 dBm	1 MHz	Note 1
Note1: Applicability of this test requirement is FFS.

6.6.3.1A.4.3 Transmitter Spurious emissions for CA (3UL CA) (intra-band non-contiguous 3DL CA and 3UL CA)

6.6.3.1A.4.3.1 Test purpose

Same as in clause 6.6.3.1A.4.1.1.

6.6.3.1A.4.3.2 Test applicability

This test case applies to all types of E-UTRA UE release 13 and forward that support intra-band non-contiguous 3DL CA and 3UL CA.

6.6.3.1A.4.3.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.1A.0

6.6.3.1A.4.3.4 Test description

6.6.3.1A.4.3.4.1 Initial conditions

Same as in clause 6.6.3.1A.4.1.4.1 with the following exceptions:

– Instead of Table 5.4.2A.1-1🡪 use Table 5.4.2A.1-2 for CA configurations with two bands or Table 5.4.2A.1-2a for CA configurations with three bands.

– Instead of Table 6.6.3.1A.4.1.4.1-1 🡪 use Table 6.6.3.1A.4.3.4.1-1.

– Instead of clause 6.6.3.1A.4.1.4.3 use clause 6.6.3.1A.4.3.4.3.

Table 6.6.3.1A.4.3.4.1-1: Test Configuration Table

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1					Normal
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.					Refer to test points A: N/A (Range is not relevant), Maximum Wgap
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.					Refer to test point Test only test points with Lowest N_RB for PCC and SCC Highest N_RB for PCC and SCC
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		W_gap[MHz]	DL Allocation		UL Allocation
	PCC N_RB	SCCs N_RB	W_gap[MHz]	CC MOD	PCC & SCC RB allocation	CC MOD	PCC N_{RB_alloc} (L_CRB @ RB_start)	CC MOD	SCC N_{RB_alloc} (L_CRB @ RB_start)
Test Parameters for CA_4A-4A Configurations
1	25	25	35	N/A		QPSK	P_1@0	QPSK	S_1@0	S_1@0
2	25	25	35			QPSK	P_1@24	QPSK	S_1@24	S_1@24
3	25	25	35			QPSK	P_25@0	QPSK	S_25@0	S_25@0
4	50	50	25			QPSK	P_1@0	QPSK	S_1@0	S_1@0
5	50	50	25			QPSK	P_1@49	QPSK	S_1@49	S_1@49
6	50	50	25			QPSK	P_50@0	QPSK	S_50@0	S_50@0
7	100	100	5			QPSK	P_1@0	QPSK	S_1@0	S_1@0
8	100	100	5			QPSK	P_1@99	QPSK	S_1@99	S_1@99
9	100	100	5			QPSK	P_100@0	QPSK	S_100@0	S_100@0
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration, which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-3. Note 2: The measurements need to be executed for in-gap interferer positions when the sub-block gap size W_gap allows.

6.6.3.1A.4.3.4.2 Test procedure

1. Configure SCCs according to Annex C.0, C.1 and Annex C.3.0 for all downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4.

3. SS activates SCCs by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

5. Send continuously uplink power control “up” commands in every uplink scheduling information to the UE until the UE transmits at P_UMAX level.

7. Repeat the measurement for in-gap interferer positions when the sub-block gap size W_gap allows.

6.6.3.1A.4.3.4.3 Message contents

Message contents are according to TS 36.508 [7] subclause 4.6.

6.6.3.1A.4.3.5 Test requirement

This clause specifies the requirements for the specified E-UTRA band for Transmitter Spurious emissions requirement with frequency range as indicated in table 6.6.3.1A.4.3.5-1.

Table 6.6.3.1A.4.3.5-1: Spurious emissions limits

Frequency Range	Maximum Level	Measurement Bandwidth	Notes
9 kHz ≤ f < 150 kHz	-36 dBm	1 kHz
150 kHz ≤ f < 30 MHz	-36 dBm	10 kHz
30 MHz ≤ f < 1000 MHz	-36 dBm	100 kHz
1 GHz ≤ f < 12.75 GHz	-30 dBm	1 MHz

6.6.3.1A.5 Transmitter Spurious emissions for CA (4UL CA)

6.6.3.1A.5.1 Test purpose

To verify that transmitter of UE that support CA does not cause unacceptable interference to other channels or other systems in terms of transmitter spurious emissions.

6.6.3.1A.5.2 Test applicability

This test case applies to all types of E-UTRA UE release 11 and forward that support inter-band and 4UL CA.

6.6.3.1A.5.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.1A.0.

6.6.3.1A.5.4 Test description

6.6.3.1A.5.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and CC combinations based on E‑UTRA CA configurations specified in table 5.4.2A.1-2. All of these configurations shall be tested with applicable test parameters for each CA Configuration, and are shown in table 6.6.3.1A.5.4.1-1. The details of the uplink and downlink reference measurement channels (RMCs) are specified in Annexe A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.1A.5.4.1-1: inter-band CA Test Configuration Table

Initial Conditions
Test Environment as specified in TS 36.508 [7] subclause 4.1							NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.							Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE (Note 1).							Lowest N_{RB_agg}Highest N_{RB_agg} (Note 2)
Test Parameters for CA Configurations
CA Configuration / N_{RB_agg} DL Allocation					DL Allocation	CC MOD	UL Allocation
ID	PCC N_RB	SCC1 N_RB	SCC2 N_RB	SCC3 N_RB	PCC & SCC RB allocation		N_{RB_ alloc}	PCC & SCC1 & SCC2 & SCC3 RB allocations (L_CRB @ RB_start)
1	100	50	100	50		QPSK	2	P_1@0	S_0@0	S_1@0	S_0@0
2	100	50	100	50		QPSK	2	P_1@99	S_0@0	S_1@99	S_0@0
3	100	50	100	50		QPSK	300	P_100@0	S_50@0	S_100@0	S_50@0
4	100	100	100	100		QPSK	2	P_1@0	S_0@0	S_1@0	S_0@0
5	100	100	100	100		QPSK	2	P_1@99	S_0@0	S_1@99	S_0@0
6	100	100	100	100		QPSK	400	P_100@0	S_100@0	S_100@0	S_100@0
NOTE 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration, which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-2. NOTE 2: If the UE supports multiple CC Combinations in the CA Configuration with the same N_{RB_agg}, only the combination with the highest NRB_PCC is tested.

1. Connect the SS to the UE antenna connectors as shown in TS 36.508[7] Annex A Figure group A.56 as appropriate.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals for PCC are initially set up according to Annex C.0, C.1, and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channel is set according to Table 6.6.3.1A.5.4.1-1.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.1A.5.4.3.

6.6.3.1A.5.4.2 Test procedure

1. Configure SCCs according to Annex C.0, C.1 and Annex C.3.0 for all downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4. Message contents are defined in clause 6.6.3.1A.5.4.3

3. SS activates SCCs by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 6.6.3.1A.5.4.1-1 on all PCC and SCCs. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

5. Send continuously uplink power control “up” commands in every uplink scheduling information to the UE until the UE transmits at P_UMAX level.

6. Measure the power of the transmitted signal with a measurement filter of bandwidths according to Table 6.6.3.1A.5.5-1 for each component carrier. The centre frequency of the filter shall be stepped in contiguous steps according to Table 6.6.3.1A.5.5-1. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

6.6.3.1A.5.4.3 Message contents

Message contents are according to TS 36.508 [7] subclause 4.6. In test procedure step 2, for SCC configuration there are no additional message contents.

6.6.3.1A.5.5 Test Requirements

This clause specifies the requirements for the specified E-UTRA band for Transmitter Spurious emissions requirement with frequency range as indicated in table 6.6.3.1A.5.5-1.

For frequencies Δf_OOB greater than F_OOB as specified in Table 6.6.3.1A.0-1 the measured average power of spurious emission, derived in step 6, shall not exceed the described value in Table 6.6.3.1A.5.5-1.

Table 6.6.3.1A.5.5-1: Spurious emissions limits

Frequency Range	Maximum Level	Measurement Bandwidth	Notes
Test requirements for CA_41C-42C Configuration
710 MHz £ f £ 1000 MHz	-36 dBm	100 kHz
1000 MHz £ f £ 1104 MHz 1392 MHz £ f £ 1980 MHz 4110 MHz £ f £ 4704 MHz 5896 MHz £ f £ 6290 MHz 8392 MHz £ f £ 8980 MHz 9296 MHz £ f £ 9890 MHz	-30 dBm	1 MHz

6.6.3.2 Spurious emission band UE co-existence

Editor’s note: This test case contains different requirements for different UE releases

6.6.3.2.1 Test purpose

To verify that UE transmitter does not cause unacceptable interference to co-existing systems for the specified bands which has specific requirements in terms of transmitter spurious emissions.

6.6.3.2.2 Test applicability

This test case applies to all types of E-UTRA UE release 8 and forward.

6.6.3.2.3 Minimum conformance requirements

This clause specifies the requirements for the specified E-UTRA band for coexistence with protected bands as indicated in Table 6.6.3.2.3-1.

Table 6.6.3.2.3-1: Spurious emission band UE co-existence limits Rel-8

E-UTRA Band	Spurious emission
E-UTRA Band	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Comment
1	E-UTRA Band 1, 3, 7, 8, 9, 11, 34, 38, 40	FDL_low	–	FDL_high	-50	1
	Frequency range	860	–	895	-50	1
	Frequency range	1475.9	–	1510.9	-50	1
	Frequency range	1895	–	1915	-15.5	5	Note¹⁴, Note¹⁷
	Frequency range	1915	–	1920	+1.6	5	Note¹⁴, Note¹⁷
2	E-UTRA Band 4, 5, 10, 12, 13, 14, 17	FDL_low	–	FDL_high	-50	1
2	E-UTRA Band 2	FDL_low	–	FDL_high	-50		Note¹⁴
3	E-UTRA Band 1, 7, 8, 33, 34, 38	FDL_low	–	FDL_high	-50	1
	E-UTRA Band 3	FDL_low	–	FDL_high	-50		Note¹⁴
	Frequency range	860	–	895	-50	1	Note¹³
	Frequency range	1475.9	–	1510.9	-50	1	Note¹³
	Frequency range	1884.5	–	1915.7	-41	0.3	Note¹³
4	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17	FDL_low	–	FDL_high	-50	1
5	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17	FDL_low	–	FDL_high	-50	1
6	E-UTRA Band 1, 9, 11, 34	FDL_low	–	FDL_high	-50	1
	Frequency range	860	–	875	-37	1
	Frequency range	875	–	895	-50	1
	Frequency range	1884.5	–	1919.6	-41	0.3	Note⁷
	Frequency range	1884.5	–	1915.7	-41	0.3	Note⁸
7	E-UTRA Band 1, 3, 7, 8, 33, 34	FDL_low	–	FDL_high	-50	1
	Frequency range	2570	–	2575	+1.6	5	Note¹⁴ , Note¹⁵, Note¹⁸
	Frequency range	2575	–	2595	-15.5	5	Note¹⁴, Note¹⁵, Note¹⁸
8	E-UTRA Band 1, 33, 34, 38, 39, 40	FDL_low	–	FDL_high	-50	1
	E-UTRA band 3	FDL_low	–	FDL_high	-50	1	Note ²
	E-UTRA band 7	FDL_low	–	FDL_high	-50	1	Note ²
	E-UTRA Band 8	FDL_low	–	FDL_high	-50	1	Note¹⁴
9	E-UTRA Band 1, 9, 11, 34	FDL_low	–	FDL_high	-50	1
	Frequency range	860	–	895	-50	1
	Frequency range	1475.9	–	1510.9	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	Note⁸
10	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17	FDL_low	–	FDL_high	-50	1
11	E-UTRA Band 1, 9, 11, 34	FDL_low	–	FDL_high	-50	1
	Frequency range	1457.9	–	1510.9	-50	1
	Frequency range	860	–	895	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	Note⁸
12	E-UTRA Band 2, 5, 13, 14, 17	FDL_low	–	FDL_high	-50	1
	E-UTRA Band 4, 10	FDL_low	–	FDL_high	-50	1	Note²
	E-UTRA Band 12	FDL_low	–	FDL_high	-50	1	Note¹⁴
13	E-UTRA Band 2, 4, 5, 10, 12, 13, 17	FDL_low	–	FDL_high	-50	1
	E-UTRA Band 14	FDL_low	–	FDL_high	-50	1	Note¹⁴
	Frequency range	769	–	775	-35	0.00625	Note¹⁴
	Frequency range	799	–	805	-35	0.00625	Note¹¹, Note¹⁴
14	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17	FDL_low	–	FDL_high	-50	1
	Frequency range	769	–	775	-35	0.00625	Note¹² Note¹⁴
	Frequency range	799	–	805	-35	0.00625	Note¹¹, Note¹² Note¹⁴
17	E-UTRA Band 2, 5, 13, 14, 17	FDL_low	–	FDL_high	-50	1
	E-UTRA Band 4, 10	FDL_low	–	FDL_high	-50	1	Note²
	E-UTRA Band 12	FDL_low	–	FDL_high	-50	1	Note¹⁴
…
33	E-UTRA Band 1, 7, 8, 34, 38, 40	FDL_low	–	FDL_high	-50	1	Note⁵
33	E-UTRA Band 3	FDL_low	–	FDL_high	-50	1	Note¹⁴
34	E-UTRA Band 1, 3, 7, 8, 9, 11, 33, 38, 39, 40	FDL_low	–	FDL_high	-50	1	Note⁵
	Frequency range	860	–	895	-50	1
	Frequency range	1475.9	–	1510.9	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	Note⁸
35
36
37			–
38	E-UTRA Band 1, 3, 8, 33, 34	FDL_low	–	FDL_high	-50	1
38	Frequency range	2620	–	2645	-15.5	5	Note¹⁴, Note¹⁶, Note¹⁸
39	E-UTRA Band 34, 40	FDL_low	–	FDL_high	-50	1
40	E-UTRA Band 1, 3, 33, 34, 39	FDL_low	–	FDL_high	-50	1
Note 1: FDL_low and FDL_high refer to each E-UTRA frequency band specified in Table 5.2-1 Note 2: As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1.3-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2nd or 3rd harmonic spurious emissions. An exception is allowed if there is at least one individual RE within the transmission bandwidth (see Figure 5.4.2-1) for which the 2nd or 3rd harmonic, i.e. the frequency equal to two or three times the frequency of that RE, is within the measurement bandwidth (MBW). Note 3: To meet these requirements some restriction will be needed for either the operating band or protected band Note 4: N/A Note 5: For non-synchronised TDD operation to meet these requirements some restriction will be needed for either the operating band or protected band Note 6: N/A. Note 7: Applicable when co-existence with PHS system operating in 1884.5 -1919.6MHz. Note 8: Applicable when co-existence with PHS system operating in 1884.5-1915.7MHz. Note 9: N/A Note 10: N/A Note 11: Whether the applicable frequency range should be 793-805MHz instead of 799-805MHz is TBD Note 12: The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB Note 13: Applicable when UE transmits anywhere within 1749.9 – 1784.9MHz.Applicable when the assigned E-UTRA UL operating channel is ≥1 749.9MHz and ≤ 1 784.9MHz. Note 14: These requirements also apply for the frequency ranges that are less than Δf_OOB(MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth. Note 15: This requirement is applicable for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz. This requirement is applicable without any other uplink transmission bandwidth restriction for channel bandwidths within the range 2500 – 2570 MHz. Note 16: This requirement is applicable for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2605.5 – 2607.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2597 – 2605 MHz. This requirement is applicable without any other uplink transmission bandwidth restriction for channel bandwidths within the range 2570 – 2615 MHz. For assigned carriers with bandwidths overlapping the frequency range 2615-2620 MHz the requirements apply with the maximum output power configured to +19 dBm in the IE P-Max. Note 17: This requirement is applicable for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz. This requirement is applicable without any other uplink transmission bandwidth restriction for channel bandwidths within the range 1920 – 1980 MHz. Note 18: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band.

NOTE: The restriction on the maximum uplink transmission to 54 RB in Notes 15, 16, and 17 of Table 6.6.3.2.3-1 is intended for conformance testing and may be applied to network operation to facilitate coexistence when the aggressor and victim bands are deployed in the same geographical area. The applicable spurious emission requirement of -15.5 dBm/5MHz is a least restrictive technical condition for FDD/TDD coexistence and may have to be revised in the future.

Table 6.6.3.2.3-1A: Spurious emission band UE co-existence limits Rel-9

E-UTRA Band	Spurious emission
E-UTRA Band	Protected band	Frequency range (MHz)			Maximum level (dBm)	MBW (MHz)	NOTE
1	E-UTRA Band 1, 3, 7, 8, 11, 20, 21, 34, 38, 40	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	895	-50	1
	Frequency range	1880	–	1895	-40	1	14,18
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	1895	–	1915	-15.5	5	14,18,19
	Frequency range	1915	–	1920	+1.6	5	14,18,19
2	E-UTRA Band 4, 5, 10, 12, 13, 14, 17	F_{DL_low}	–	F_{DL_high}	-50	1
2	E-UTRA Band 2	F_{DL_low}	–	F_{DL_high}	-50	1	14
3	E-UTRA Band 1, 7, 8, 20, 33, 34, 38	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	14
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	13
	Frequency range	860	–	895	-50	1	13
	Frequency range	1884.5	–	1915.7	-41	0.3	13
4	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17	F_{DL_low}	–	F_{DL_high}	-50	1
5	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17	F_{DL_low}	–	F_{DL_high}	-50	1
6	E-UTRA Band 1, 9, 11, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	875	-37	1
	Frequency range	875	–	895	-50	1
	Frequency range	1884.5	–	1919.6	-41	0.3	7
	Frequency range	1884.5	–	1915.7	-41	0.3	8
7	E-UTRA Band 1, 3, 7, 8, 20, 33, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2570	–	2575	-+1.6	5	14, 15, 19
	Frequency range	2575	–	2595	-15.5	5	14, 15, 19
	Frequency range	2595	–	2620	-40	1	14, 15
8	E-UTRA Band 1, 20, 33, 34, 38, 39, 40	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA band 7	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}	–	F_{DL_high}	-50	1	14
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	17
	Frequency range	860	–	890	-40	1	14, 17
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 17
9	E-UTRA Band 1, 11, 21, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	895	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
10	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17	F_{DL_low}	–	F_{DL_high}	-50	1
11	E-UTRA Band 1, 9, 11, 21, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	895	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
12	E-UTRA Band 2, 5, 13, 14, 17	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	14
13	E-UTRA Band 2, 4, 5, 10, 12, 13, 17	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 14	F_{DL_low}	–	F_{DL_high}	-50	1	14
	Frequency range	769	–	775	-35	0.00625	14
	Frequency range	799	–	805	-35	0.00625	11, 14
14	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	769	–	775	-35	0.00625	12, 14
	Frequency range	799	–	805	-35	0.00625	11, 12, 14
17	E-UTRA Band 2, 5, 13, 14, 17	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	14
18	E-UTRA Band 1, 11, 21, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	895	-40	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
19	E-UTRA Band 1, 11, 21, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
20	E-UTRA Band 1, 3, 7, 8, 33, 34,	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	14
	E-UTRA Band 38	F_{DL_low}	–	F_{DL_high}	-50	1	2
21	E-UTRA Band 1, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	895	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
33	E-UTRA Band 1, 7, 8, 20, 34, 38, 40	F_{DL_low}	–	F_{DL_high}	-50	1	5
33	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	14
34	E-UTRA Band 1, 3, 7, 8, 11, 20, 21, 33, 38,39, 40	F_{DL_low}	–	F_{DL_high}	-50	1	5
	Frequency range	860	–	895	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	1839.9	–	1879.9	-50	1
35			–
36			–
37			–
38	E-UTRA Band 1,3, 8, 20, 33, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2620	–	2645	-15.5	5	14, 16, 19
	Frequency range	2645	–	2690	-40	1	14, 16
39	E-UTRA Band 34, 40	F_{DL_low}	–	F_{DL_high}	-50	1
40	E-UTRA Band 1, 3, 33, 34, 39	F_{DL_low}	–	F_{DL_high}	-50	1
Note 1:FDL_low and FDL_high refer to each E-UTRA frequency band specified in Table 5.2-1 Note 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1.3-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2nd or 3rd harmonic spurious emissions. An exception is allowed if there is at least one individual RE within the transmission bandwidth (see Figure 5.4.2-1) for which the 2nd or 3rd harmonic, i.e. the frequency equal to two or three times the frequency of that RE, is within the measurement bandwidth (MBW). Note 3:To meet these requirements some restriction will be needed for either the operating band or protected band Note 4: N/A Note 5:For non-synchronised TDD operation to meet these requirements some restriction will be needed for either the operating band or protected band Note 6:N/A Note 7:Applicable when co-existence with PHS system operating in 1884.5 -1919.6MHz. Note 8:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. Note 9:N/A Note 10:N/A Note 11:Whether the applicable frequency range should be 793-805MHz instead of 799-805MHz is TBD Note 12:The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB Note 13:Applicable when the assigned E-UTRA UL operating channel is ≥1744.9MHz and ≤ 1784.9MHz. Note 14:These requirements also apply for the frequency ranges that are less than Δf_OOB(MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth. Note 15: This requirement is applicable for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz. This requirement is applicable without any other uplink transmission bandwidth restriction for channel bandwidths within the range 2500 – 2570 MHz. Note 16: This requirement is applicable for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2605.5 – 2607.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2597 – 2605 MHz. This requirement is applicable without any other uplink transmission bandwidth restriction for channel bandwidths within the range 2570 – 2615 MHz. For assigned carriers with bandwidths overlapping the frequency range 2615-2620 MHz the requirements apply with the maximum output power configured to +19 dBm in the IE P-Max. Note 17: For carriers of 5 MHz channel bandwidth with carrier centre frequencies (F_c) in the range 902.5MHz ≤ F_c < 907.5 MHz, the requirement applies for uplink transmission bandwidths less than or equal to 20 RB. No restrictions apply in the range 907.5 MHz ≤ F_c ≤ 912.5 MHz. For carriers of 10 MHz channel bandwidth, the requirement only applies for F_c = 910 MHz and uplink transmission bandwidths less than or equal to 32 RB with RB_start > 3. Note 18: This requirement is applicable for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz. This requirement is applicable without any other uplink transmission bandwidth restriction for channel bandwidths within the range 1920 – 1980 MHz. Note 19: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band.

NOTE: The restriction on the maximum uplink transmission to 54 RB in Notes 15, 16 and 18 of Table 6.6.3.2.3-1A is intended for conformance testing and may be applied to network operation to facilitate coexistence when the aggressor and victim bands are deployed in the same geographical area. The applicable spurious emission requirement of -15.5 dBm/5MHz is a least restrictive technical condition for FDD/TDD coexistence and may have to be revised in the future.

Table 6.6.3.2.3-1B: Spurious emission band UE co-existence limits Rel-10

E-UTRA Band	Spurious emission
E-UTRA Band	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Note
1	E-UTRA Band 1, 7, 8, 11, 18, 19, 20, 21, 22, 38, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3, 34	F_{DL_low}	–	F_{DL_high}	-50	1	15
	Frequency range	1880	–	1895	-40	1	15,19
	Frequency range	1895	–	1915	-15.5	5	15,19,20
	Frequency range	1915	–	1920	+1.6	5	15,19,20
	Frequency range	1839.9	–	1879.9	-50	1	15
2	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 23, 24, 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
3	E-UTRA Band 1, 7, 8, 20, 33, 34, 38, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	13
	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	13
4	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 22, 23, 24, 25, 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1
4	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
5	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 22, 23, 24, 25, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
5	E-UTRA Band 41	F_{DL_low}	–	F_{DL_high}	-50	1	2
6	E-UTRA Band 1, 9, 11, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	875	-37	1
	Frequency range	875	–	895	-50	1
	Frequency range	1884.5	–	1919.6	-41	0.3	7
	Frequency range	1884.5	–	1915.7	-41	0.3	8
7	E-UTRA Band 1, 3, 7, 8, 20, 22, 33, 34, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2570	–	2575	+1.6	5	15, 16, 20
	Frequency range	2575	–	2595	-15.5	5	15, 16, 20
	Frequency range	2595	–	2620	-40	1	15, 16
8	E-UTRA Band 1, 20, 33, 34, 38, 39, 40	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA band 7	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 22, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	18
	Frequency range	860		890	-40	1	15, 18
	Frequency range	1884.5		1915.7	-41	0.3	8, 18
9	E-UTRA Band 1, 11, 18, 19, 21, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
10	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 23, 24, 25, 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1
10	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
11	E-UTRA Band 1, 11, 18, 19, 21, 34, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
12	E-UTRA Band 2, 5, 13, 14, 17, 23, 24, 25, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	15
13	E-UTRA Band 2, 4, 5, 10, 12, 13, 17, 23, 25, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	769	–	775	-35	0.00625	15
	Frequency range	799	–	805	-35	0.00625	11, 15
	E-UTRA Band 14	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 24	F_{DL_low}	–	F_{DL_high}	-50	1	2
14	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 23, 24, 25, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	769	–	775	-35	0.00625	12, 15
	Frequency range	799	–	805	-35	0.00625	11, 12, 15
17	E-UTRA Band 2, 5, 13, 14, 17, 23, 24, 25, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	15
18	E-UTRA Band 1, 11, 21, 34, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	890	-40	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
19	E-UTRA Band 1, 11, 21, 34, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
20	E-UTRA Band 1, 3, 7, 8, 20, 22, 33, 34, 40, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 1, 18, 19, 34, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
22	E-UTRA Band 1, 3, 7, 8, 20, 33, 34, 38, 39, 40, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	3510	–	3525	-40	1	15
	Frequency range	3525	–	3590	-50	1
23	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 23, 24, 41	F_{DL_low}	–	F_{DL_high}	-50	1
24	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 23, 24, 25, 41	F_{DL_low}	–	F_{DL_high}	-50	1
25	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 23, 24, 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 25	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
…
33	E-UTRA Band 1, 7, 8, 20, 22, 34, 38, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	5
33	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
34	E-UTRA Band 1, 3, 7, 8, 11, 18, 19, 20, 21, 22, 33, 38, 39, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	5
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	1839.9	–	1879.9	-50	1
35
36
37			–
38	E-UTRA Band 1, 3, 8, 20, 22, 33, 34, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2620	–	2645	-15.5	5	15, 17, 20
	Frequency range	2645	–	2690	-40	1	15, 17
39	E-UTRA Band 22, 34, 40, 42	F_{DL_low}	–	F_{DL_high}	-50	1
39	E-UTRA Band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
40	E-UTRA Band 1, 3, 7, 8, 20, 22, 33, 34, 38, 39, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
41	E-UTRA Band 2, 4, 5, 10, 12, 13 , 14, 17, 23, 24, 25	F_{DL_low}	–	F_{DL_high}	-50	1
42	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 11, 18, 19, 20, 21, 25, 33, 34, 38, 40	F_{DL_low}	–	F_{DL_high}	-50	1
42	Frequency range	1884.5	–	1915.7	-41	0.3	8
43	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 20, 25, 33, 34, 38, 40	F_{DL_low}	–	F_{DL_high}	-50	1
Note 1:F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.2-1 Note 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1.3-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th ] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th [or 5^th ] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. Note 3: N/A Note 4: N/A Note 5:For non-synchronised TDD operation to meet these requirements some restriction will be needed for either the operating band or protected band Note 6:N/A Note 7:Applicable when co-existence with PHS system operating in 1884.5 -1919.6MHz. Note 8:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. Note 9:N/A Note 10:N/A Note 11:Whether the applicable frequency range should be 793-805MHz instead of 799-805MHz is TBD Note 12:The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB Note 13:This requirement applies for 5, 10, 15 and 20 MHz E-UTRA channel bandwidth allocated within 1744.9MHz and 1784.9MHz. Note 14: N/A Note 15:These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.1.3-1 from the edge of the channel bandwidth. NOTE16:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE17:This requirement is applicable for any channel bandwidths within the range 2570 – 2615 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2605.5 – 2607.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2597 – 2605 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. For carriers with channel bandwidth overlapping the frequency range 2615 – 2620 MHz the requirement applies with the maximum output power configured to +19 dBm in the IE P-Max. NOTE 18: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 19: This requirement is applicable for any channel bandwidths within the range 1920 – 1980 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. Note 20:For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. Note 21 N/A Note 22 N/A

NOTE: The restriction on the maximum uplink transmission to 54 RB in Notes 16, 17, and 19 of Table 6.6.3.2.3-1B is intended for conformance testing and may be applied to network operation to facilitate coexistence when the aggressor and victim bands are deployed in the same geographical area. The applicable spurious emission requirement of -15.5 dBm/5MHz is a least restrictive technical condition for FDD/TDD coexistence and may have to be revised in the future.

Table 6.6.3.2.3-1C: Spurious emission band UE co-existence limits Rel-11

E-UTRA Band	Spurious emission
E-UTRA Band	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Note
1	E-UTRA Band 1, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 38, 40, 41, 42, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3, 34	F_{DL_low}	–	F_{DL_high}	-50	1	15
	Frequency range	1880		1895	-40	1	15,27
	Frequency range	1895		1915	-15.5	5	15, 26, 27
	Frequency range	1915		1920	+1.6	5	15, 26, 27
	Frequency range	1839.9	–	1879.9	-50	1	15
2	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 22, 23, 24, 26, 27, 28, 29, 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
3	E-UTRA Band 1, 7, 8, 20, 26, 27, 28, 33, 34, 38, 41, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	13
	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	13
4	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 22, 23, 24, 25, 26, 27, 28, 29, 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1
4	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
5	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 22, 23, 24, 25, 28, 29,42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 41	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 26	859	–	869	-27	1
6	E-UTRA Band 1, 9, 11, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	875	-37	1
	Frequency range	875	–	895	-50	1
	Frequency range	1884.5	–	1919.6	-41	0.3	7
	Frequency range	1884.5	–	1915.7	-41	0.3	8
7	E-UTRA Band 1, 3, 7, 8, 20, 22, 27, 28, 29, 33, 34, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2570	–	2575	+1.6	5	15, 21, 26
	Frequency range	2575	–	2595	-15.5	5	15, 21, 26
	Frequency range	2595	–	2620	-40	1	15, 21
8	E-UTRA Band 1, 20, 28, 33, 34, 38, 39, 40	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA band 7	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 22, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	23
	Frequency range	860	–	890	-40	1	15, 23
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 23
9	E-UTRA Band 1, 11, 18, 19, 21, 26, 28, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
10	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 23, 24, 25, 26, 27, 28, 29, 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1
10	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
11	E-UTRA Band 1, 11, 18, 19, 21, 28, 34, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
12	E-UTRA Band 2, 5, 13, 14, 17, 23, 24, 25, 26, 27, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	15
13	E-UTRA Band 2, 4, 5, 10, 12, 13, 17, 23, 25, 26, 27, 29, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	769	–	775	-35	0.00625	15
	Frequency range	799	–	805	-35	0.00625	11, 15
	E-UTRA Band 14	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 24	F_{DL_low}	–	F_{DL_high}	-50	1	2
14	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 23, 24, 25, 26, 27, 29, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	769	–	775	-35	0.00625	12, 15
	Frequency range	799	–	805	-35	0.00625	11, 12, 15
17	E-UTRA Band 2, 5, 13, 14, 17, 23, 24, 25, 26, 27, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	15
18	E-UTRA Band 1, 11, 21, 34, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	890	-40	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	758	–	799	-50	1
	Frequency range	799	–	803	-40	1	15
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
19	E-UTRA Band 1, 11, 21, 28, 34, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
20	E-UTRA Band 1, 3, 7, 8, 20, 22, 33, 34, 40, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	758	–	788	-50	1
	E-UTRA Band 1, 18, 19, 28, 34, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
22	E-UTRA Band 1, 3, 7, 8, 20, 26, 27, 28, 33, 34, 38, 39, 40, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	3510	–	3525	-40	1	15
	Frequency range	3525	–	3590	-50	1
23	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 23, 24, 26, 27, 29, 41	F_{DL_low}	–	F_{DL_high}	-50	1
24	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 23, 24, 25, 26, 29, 41	F_{DL_low}	–	F_{DL_high}	-50	1
25	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 23, 24, 26, 27, 28, 29, 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 25	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
26	E-UTRA Band 1, 2, 3, 4, 5, 10, 11, 12, 13, 14, 17, 18, 19, 21, 23, 24, 25, 26, 29, 34, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 41	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	703	–	799	-50	1
	Frequency range	799	–	803	-40	1	15
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
27	E-UTRA Band 1, 2, 3, 4, 5, 7, 10, 12, 13, 14, 17, 23, 25, 26, 27, 29, 38, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	799	–	805	-35	0.00625
	E-UTRA Band 28
	E-UTRA Band 28	F_{DL_low}	–	790	-50	1
28	E-UTRA Band 2, 3, 5, 7, 8, 18, 19, 25, 26, 27, 34, 38, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 1, 4, 10, 22, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	19, 24
	E-UTRA Band 1	F_{DL_low}	–	F_{DL_high}	-50	1	19, 25
	Frequency range	470	–	694	-42	8	15, 32
	Frequency range	470	–	710	-26.2	6	31
	Frequency range	758	–	773	-32	1	15
	Frequency range	773	–	803	-50	1
	Frequency range	662	–	694	-26.2	6	15
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 19
	Frequency range	1839.9	–	1879.9	-50	1
…
33	E-UTRA Band 1, 7, 8, 20, 22, 28, 34, 38, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	5
33	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
34	E-UTRA Band 1, 3, 7, 8, 11, 18, 19, 20, 21, 22, 26, 28, 33, 38, 39, 40, 41, 42, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1	5
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	1839.9	–	1879.9	-50	1
35
36
37			–
38	E-UTRA Band 1,3, 8, 20, 22, 27, 28, 29, 33, 34, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2620	–	2645	-15.5	5	15, 22, 26
	Frequency range	2645	–	2690	-40	1	15, 22
39	E-UTRA Band 22, 34, 40, 41, 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
40	E-UTRA Band 1, 3, 7, 8, 20, 22, 26, 27, 28, 33, 34, 38, 39, 41, 42, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1
41	E-UTRA Band 1, 2, 3, 4, 5, 8, 10, 12, 13 , 14, 17, 23, 24, 25, 26, 27, 28, 29, 34, 39, 40, 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	30
	Frequency range	1839.9		1879.9	-50	1	30
	Frequency range	1884.5		1915.7	-41	0.3	8, 30
42	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 11, 18, 19, 20, 21, 25, 26, 27, 28, 33, 34, 38, 40, 41, 44	F_{DL_low}	–	F_{DL_high}	-50	1
42	Frequency range	1884.5	–	1915.7	-41	0.3	8
43	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 20, 25, 26, 27, 28, 33, 34, 38, 40	F_{DL_low}	–	F_{DL_high}	-50	1
44	E-UTRA Band 3, 5, 8, 34, 39, 41	F_{DL_low}	–	F_{DL_high}	-50	1
44	E-UTRA Band 1, 40, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
Note 1:F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.2-1 Note 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1.3-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th [or 5^th ] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. Note 3: N/A Note 4: N/A Note 5:For non-synchronised TDD operation to meet these requirements some restriction will be needed for either the operating band or protected band Note 6:N/A Note 7:Applicable when co-existence with PHS system operating in 1884.5 -1919.6MHz. Note 8:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. Note 9:N/A Note 10:N/A Note 11:Whether the applicable frequency range should be 793-805MHz instead of 799-805MHz is TBD Note 12:The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB Note 13:This requirement applies for 5, 10, 15 and 20 MHz E-UTRA channel bandwidth allocated within 1744.9MHz and 1784.9MHz. Note 14: N/A Note 15:These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.1.3-1 from the edge of the channel bandwidth. Note 16: N/A Note 17: N/A Note 18: N/A Note 19:Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. Note 20:N/A Note21:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. Note22:This requirement is applicable for any channel bandwidths within the range 2570 – 2615 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2605.5 – 2607.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2597 – 2605 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. For carriers with channel bandwidth overlapping the frequency range 2615 – 2620 MHz the requirement applies with the maximum output power configured to +19 dBm in the IE P-Max. Note 23: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. Note 24:As exceptions, measurements with a level up to the applicable requirement of -38 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 2^ndharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 2^nd harmonic totally or partially overlaps the measurement bandwidth (MBW). Note 25:As exceptions, measurements with a level up to the applicable requirement of -36 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 3^rdharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 3^rd harmonic totally or partially overlaps the measurement bandwidth (MBW). Note 26: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. Note 27: This requirement is applicable for any channel bandwidths within the range 1920 – 1980 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. Note 28: N/A Note 29: N/A Note 30: This requirement applies when the E-UTRA carrier is confined within 2545-2575 MHz and the channel bandwidth is 10 or 20 MHz Note 31: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48. Note 32: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies.

Table 6.6.3.2.3-1D: Spurious emission band UE co-existence limits Rel-12

E-UTRA Band	Spurious emission
E-UTRA Band	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Note
1	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 38, 40, 41, 42, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3, 34	F_{DL_low}	–	F_{DL_high}	-50	1	15
	Frequency range	1880		1895	-40	1	15,27
	Frequency range	1895		1915	-15.5	5	15, 26, 27
	Frequency range	1915		1920	+1.6	5	15, 26, 27
	Frequency range	1839.9	–	1879.9	-50	1	15
2	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 22, 23, 24, 26, 27, 28, 29, 30, 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
3	E-UTRA Band 1, 5, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 41, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	13
	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	13
4	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 22, 23, 24, 25, 26, 27, 28, 29, 30, 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1
4	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
5	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 12, 13, 14, 17, 23, 24, 25, 28, 29, 30, 31, 38, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 41	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 26	859	–	869	-27	1
6	E-UTRA Band 1, 9, 11, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	875	-37	1
	Frequency range	875	–	895	-50	1
	Frequency range	1884.5	–	1919.6	-41	0.3	7
	Frequency range	1884.5	–	1915.7	-41	0.3	8
7	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 12, 13, 14, 17, 20, 22, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2570	–	2575	+1.6	5	15, 21, 26
	Frequency range	2575	–	2595	-15.5	5	15, 21, 26
	Frequency range	2595	–	2620	-40	1	15, 21
8	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA band 7	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 22, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	23
	Frequency range	860	–	890	-40	1	15, 23
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 23
9	E-UTRA Band 1, 11, 18, 19, 21, 26, 28, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
10	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 23, 24, 25, 26, 27, 28, 29, 30, 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1
10	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
11	E-UTRA Band 1, 11, 18, 19, 21, 28, 34, 40, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
12	E-UTRA Band 2, 5, 13, 14, 17, 23, 24, 25, 26, 27, 30, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	15
13	E-UTRA Band 2, 4, 5, 10, 12, 13, 17, 23, 25, 26, 27, 29, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	769	–	775	-35	0.00625	15
	Frequency range	799	–	805	-35	0.00625	11, 15
	E-UTRA Band 14	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 24, 30	F_{DL_low}	–	F_{DL_high}	-50	1	2
14	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 23, 24, 25, 26, 27, 29, 30, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	769	–	775	-35	0.00625	12, 15
	Frequency range	799	–	805	-35	0.00625	11, 12, 15
17	E-UTRA Band 2, 5, 13, 14, 17, 23, 24, 25, 26, 27, 30, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	15
18	E-UTRA Band 1, 11, 21, 34, 40, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	890	-40	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	758	–	799	-50	1
	Frequency range	799	–	803	-40	1	15
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
19	E-UTRA Band 1, 11, 21, 28, 34, 40, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
20	E-UTRA Band 1, 3, 7, 8, 20, 22, 31, 32, 33, 34, 40, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	758	–	788	-50	1
21	E-UTRA Band 1, 18, 19, 28, 34, 40, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
22	E-UTRA Band 1, 3, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 39, 40, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	3510	–	3525	-40	1	15
	Frequency range	3525	–	3590	-50	1
23	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 23, 24, 26, 27, 29, 30, 41	F_{DL_low}	–	F_{DL_high}	-50	1
24	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 23, 24, 25, 26, 29, 30, 41	F_{DL_low}	–	F_{DL_high}	-50	1
25	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 23, 24, 26, 27, 28, 29, 30, 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 25	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
26	E-UTRA Band 1, 2, 3, 4, 5, 10, 11, 12, 13, 14, 17, 18, 19, 21, 23, 24, 25, 26, 29, 30, 31, 34, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 41	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	703	–	799	-50	1
	Frequency range	799	–	803	-40	1	15
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
27	E-UTRA Band 1, 2, 3, 4, 5, 7, 10, 12, 13, 14, 17, 23, 25, 26, 27, 29, 30, 31, 38, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	799	–	805	-35	0.00625
	E-UTRA Band 28
	E-UTRA Band 28	F_{DL_low}	–	790	-50	1
28	E-UTRA Band 2, 3, 5, 7, 8, 18, 19, 20, 25, 26, 27, 31, 34, 38, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 1, 4, 10, 22, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	19, 24
	E-UTRA Band 1	F_{DL_low}	–	F_{DL_high}	-50	1	19, 25
	Frequency range	470	–	694	-42	8	15, 35
	Frequency range	470	–	710	-26.2	6	34
	Frequency range	758	–	773	-32	1	15
	Frequency range	773	–	803	-50	1
	Frequency range	662	–	694	-26.2	6	15
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 19
	Frequency range	1839.9	–	1879.9	-50	1
30	E-UTRA Band 2, 4, 5, 7, 10, 12, 13, 14, 17, 23, 24, 25, 26, 27, 29, 30, 38, 41	F_{DL_low}	–	F_{DL_high}	-50	1
31	E-UTRA Band 1, 5, 7, 8, 20, 22, 26, 27, 28,31, 32, 33, 34, 38, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
31	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2
…
33	E-UTRA Band 1, 7, 8, 20, 22, 28, 31, 32, 34, 38, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	5
33	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
34	E-UTRA Band 1, 3, 7, 8, 11, 18, 19, 20, 21, 22, 26, 28, 31, 32, 33, 38, 39, 40, 41, 42, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1	5
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	1839.9	–	1879.9	-50	1
35
36
37			–
38	E-UTRA Band 1, 2, 3, 4, 5, 8, 10, 12, 13, 14, 17, 20, 22, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2620	–	2645	-15.5	5	15, 22, 26
	Frequency range	2645	–	2690	-40	1	15, 22
39	E-UTRA Band 22, 34, 40, 41, 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1805		1855	-40	1	33
	Frequency range	1855		1880	-15.5	5	15,26,33
40	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 33, 34, 38, 39, 41, 42, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	1475	–	1518	-50	1
	Frequency range	3300	–	4200	-50	1
	Frequency range	4400	–	5000	-50	1	2
41	E-UTRA Band 1, 2, 3, 4, 5, 8, 10, 12, 13 , 14, 17, 23, 24, 25, 26, 27, 28, 29, 30, 34, 39, 40, 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	30
	Frequency range	1839.9		1879.9	-50	1	30
	Frequency range	1884.5		1915.7	-41	0.3	8, 30
42	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 11, 18, 19, 20, 21, 25, 26, 27, 28, 31, 32, 33, 34, 38, 40, 41, 44	F_{DL_low}	–	F_{DL_high}	-50	1
42	Frequency range	1884.5	–	1915.7	-41	0.3	8
43	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 20, 25, 26, 27, 28, 31, 32, 33, 34, 38, 40	F_{DL_low}	–	F_{DL_high}	-50	1
44	E-UTRA Band 3, 5, 8, 34, 39, 41	F_{DL_low}	–	F_{DL_high}	-50	1
44	E-UTRA Band 1, 40, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
Note 1:F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 Note 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1.3-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th [or 5^th ] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. Note 3: N/A Note 4: N/A Note 5:For non-synchronised TDD operation to meet these requirements some restriction will be needed for either the operating band or protected band Note 6:N/A Note 7:Applicable when co-existence with PHS system operating in 1884.5 -1919.6MHz. Note 8:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. Note 9:N/A Note 10:N/A Note 11:Whether the applicable frequency range should be 793-805MHz instead of 799-805MHz is TBD Note 12:The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB Note 13:This requirement applies for 5, 10, 15 and 20 MHz E-UTRA channel bandwidth allocated within 1744.9MHz and 1784.9MHz. Note 14: N/A Note 15:These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.1.3-1 from the edge of the channel bandwidth. Note 16: N/A Note 17: N/A Note 18: N/A Note 19:Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. Note 20:N/A Note21:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. Note22:This requirement is applicable for any channel bandwidths within the range 2570 – 2615 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2605.5 – 2607.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2597 – 2605 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. For carriers with channel bandwidth overlapping the frequency range 2615 – 2620 MHz the requirement applies with the maximum output power configured to +19 dBm in the IE P-Max. Note 23 This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. Note 24:As exceptions, measurements with a level up to the applicable requirement of -38 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 2^ndharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 2^nd harmonic totally or partially overlaps the measurement bandwidth (MBW). Note 25:As exceptions, measurements with a level up to the applicable requirement of -36 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 3^rdharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 3^rd harmonic totally or partially overlaps the measurement bandwidth (MBW). Note 26: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. Note 27: This requirement is applicable for any channel bandwidths within the range 1920 – 1980 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. Note 28: N/A Note 29: N/A Note 30: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz Note 31: N/A Note 32: Void. Note 33: This requirement is only applicable for carriers with bandwidth confined within 1885-1920 MHz (requirement for carriers with at least 1RB confined within 1880 – 1885 MHz is not specified). This requirement applies for an uplink transmission bandwidth less than or equal to [54 RB] for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1892.5 – 1894.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1895 – 1903 MHz. Note 34: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48. Note 35: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies.

Table 6.6.3.2.3-1E: Spurious emission band UE co-existence limits Rel-13

E-UTRA Band	Spurious emission
E-UTRA Band	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
1	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 38, 40, 41, 42, 43, 44, 45, 65, 67, 68	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	15
	Frequency range	1880	–	1895	-40	1	15, 27
	Frequency range	1895		1915	-15.5	5	15, 26, 27
	Frequency range	1915		1920	+1.6	5	15, 26, 27, 39
2	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 23, 24, 26, 27, 28, 29, 30, 41, 42, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
3	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 33, 34, 38, 39, 40, 41, 43, 44, 45, 65, 67, 68	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3
4	E-UTRA Band 2, 4, 5, 7, 10, 12, 13, 14, 17, 23, 24, 25, 26, 27, 28, 29, 30, 41, 43, 66	F_{DL_low}	–	F_{DL_high}	-50	1
4	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
5	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 12, 13, 14, 17, 23, 24, 25, 28, 29, 30, 31, 34, 38, 40, 42, 43, 45, 65, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 26	859	–	869	-27	1
	E-UTRA Band 41	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 18, 19	F_{DL_low}	–	F_{DL_high}	-40	1	38
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	38
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 38
6	E-UTRA Band 1, 9, 11, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	875	-37	1
	Frequency range	875	–	895	-50	1
	Frequency range	1884.5	–	1919.6	-41	0.3	7
	Frequency range	1884.5	–	1915.7	-41	0.3	8
7	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 12, 13, 14, 17, 20, 22, 26, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 65, 66, 67, 68	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2570	–	2575	+1.6	5	15, 21, 26
	Frequency range	2575	–	2595	-15.5	5	15, 21, 26
	Frequency range	2595	–	2620	-40	1	15, 21
8	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40, 45, 65, 67, 68	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3, 7, 22, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	23
	Frequency range	860	–	890	-40	1	15, 23
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 23
9	E-UTRA Band 1, 3, 11, 18, 19, 21, 26, 28, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
10	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 23, 24, 25, 26, 27, 28, 29, 30, 41, 43, 66	F_{DL_low}	–	F_{DL_high}	-50	1
10	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
11	E-UTRA Band 1, 3, 11, 18, 19, 21, 28, 34, 40, 42, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
12	E-UTRA Band 2, 5, 13, 14, 17, 23, 24, 25, 26, 27, 30, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10, 66	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	15
13	E-UTRA Band 2, 4, 5, 10, 12, 13, 17, 23, 25, 26, 27, 29, 41, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 14	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 24, 30	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	769	–	775	-35	0.00625	15
	Frequency range	799	–	805	-35	0.00625	11, 15
14	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 23, 24, 25, 26, 27, 29, 30, 41, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	769	–	775	-35	0.00625	12, 15
	Frequency range	799	–	805	-35	0.00625	11, 12, 15
17	E-UTRA Band 2, 5, 13, 14, 17, 23, 24, 25, 26, 27, 30, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10, 66	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	15
18	E-UTRA Band 1, 3, 11, 21, 34, 40, 42, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	758	–	799	-50	1
	Frequency range	799	–	803	-40	1	15
	Frequency range	860	–	890	-40	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
19	E-UTRA Band 1, 3, 11, 21, 28, 34, 40, 42, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
20	E-UTRA Band 1, 3, 7, 8, 22, 31, 32, 33, 34, 40, 43, 65, 67, 68	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	758	–	788	-50	1
21	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 42, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
22	E-UTRA Band 1, 3, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 39, 40, 43, 65, 67, 68	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	3510	–	3525	-40	1	15
	Frequency range	3525	–	3590	-50	1
23	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 23, 24, 26, 27, 29, 30, 41, 66	F_{DL_low}	–	F_{DL_high}	-50	1
24	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 23, 24, 25, 26, 29, 30, 41, 66	F_{DL_low}	–	F_{DL_high}	-50	1
25	E-UTRA Band 4, 5, 10,12, 13, 14, 17, 23, 24, 26, 27, 28, 29, 30, 41, 42, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
26	E-UTRA Band 1, 2, 3, 4, 5, 10, 11, 12, 13, 14, 17, 18,19, 21, 23, 24, 25, 26, 29, 30, 31, 34, 39, 40, 42, 43, 65, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 41	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	703	–	799	-50	1
	Frequency range	799	–	803	-40	1	15
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
27	E-UTRA Band 1, 2, 3, 4, 5, 7, 10, 12, 13, 14, 17, 23, 25, 26, 27, 29, 30, 31, 38, 40, 41, 42, 43, 65, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 28	F_{DL_low}	–	790	-50	1
	Frequency range	799	–	805	-35	0.00625
28	E-UTRA Band 1, 4, 10, 22, 42, 43, 65, 66	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}	–	F_{DL_high}	-50	1	19, 25
	E-UTRA Band 2, 3, 5, 7, 8, 18, 19, 20, 25, 26, 27, 31, 34, 38, 40, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	19, 24
	Frequency range	470	–	694	-42	8	15, 35
	Frequency range	470	–	710	-26.2	6	34
	Frequency range	662	–	694	-26.2	6	15
	Frequency range	758	–	773	-32	1	15
	Frequency range	773	–	803	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 19
30	E-UTRA Band 2, 4, 5, 7, 10, 12, 13, 14, 17, 23, 24, 25, 26, 27, 29, 30, 38, 41, 66	F_{DL_low}	–	F_{DL_high}	-50	1
31	E-UTRA Band 1, 5, 7, 8, 20, 22, 26, 27, 28, 31, 32, 33, 34, 38, 40, 42, 43, 65, 67, 68	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	470	–	694	-42	8
…
33	E-UTRA Band 1, 7, 8, 20, 22, 28, 31, 32, 34, 38, 40, 42, 43, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1	5
33	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
34	E-UTRA Band 1, 3, 7, 8, 11, 18, 19, 20, 21, 22, 26, 28, 31, 32, 33, 38,39, 40, 41, 42, 43, 44, 45, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1	5
34	Frequency range	1884.5	–	1915.7	-41	0.3	8
35
36
37			–
38	E-UTRA Band 1, 2, 3, 4, 5, 8, 10, 12, 13, 14, 17, 20, 22, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 65, 66, 67, 68	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2620	–	2645	-15.5	5	15, 22, 26
	Frequency range	2645	–	2690	-40	1	15, 22
39	E-UTRA Band 1, 8, 22, 26, 34, 40, 41, 42, 44, 45	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1805		1855	-40	1	33
	Frequency range	1855		1880	-15.5	5	15,26,33
40	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 33, 34, 38, 39, 41, 42, 43, 44, 45, 65, 67, 68	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	1475	–	1518	-50	1
	Frequency range	3300	–	4200	-50	1
	Frequency range	4400	–	5000	-50	1	2
41	E-UTRA Band 1, 2, 3, 4, 5, 8, 10, 12, 13 , 14, 17, 23, 24, 25, 26, 27, 28, 29, 30, 34, 39, 40, 42, 44, 45, 65, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	30
	Frequency range	1884.5		1915.7	-41	0.3	8, 30
42	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 11, 18, 19, 20, 21, 25, 26, 27, 28, 31, 32, 33, 34, 38, 40, 41, 44, 45, 65, 66, 67, 68	F_{DL_low}	–	F_{DL_high}	-50	1
42	Frequency range	1884.5	–	1915.7	-41	0.3	8
43	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 20, 25, 26, 27, 28, 31,32, 33, 34, 38, 40, 65, 66, 67, 68	F_{DL_low}	–	F_{DL_high}	-50	1
44	E-UTRA Band 1, 40, 42, 45	F_{DL_low}	–	F_{DL_high}	-50	1	2
44	E-UTRA Band 3, 5, 8, 34, 39, 41	F_{DL_low}	–	F_{DL_high}	-50	1
45	E-UTRA Band 1, 3, 5, 8, 34, 39, 40, 41, 42.44	F_{DL_low}	–	F_{DL_high}	-50	1
65	E-UTRA Band 1, 3, 7, 8, 20, 22, 28, 31, 32, 38, 40, 42, 43, 65, 68	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 5, 11, 18, 19, 21, 26, 27, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	36
	Frequency range	1884.5	–	1915.7	-41	0.3	37
	Frequency range	1900	–	1915	-15.5	5	15, 26, 27
	Frequency range	1915	–	1920	+1.6	5	15, 26, 27
66	E-UTRA Band 2, 4, 5, 7, 10, 12, 13, 14, 17, 23, 24, 25, 26, 27, 28, 29, 30, 38, 41, 43, 66	F_{DL_low}	–	F_{DL_high}	-50	1
66	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
68	E-UTRA Band 3, 7, 8, 20, 22, 28, 31, 38, 40, 42, 43, 65	F_{DL_low}	–	F_{DL_high}	-50	1
68	E-UTRA Band 1	F_{DL_low}	–	F_{DL_high}	-50	1	2
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2: As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1.3-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th [or 5^th] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3: N/A NOTE 4: N/A NOTE 5: For non-synchronised TDD operation to meet these requirements some restriction will be needed for either the operating band or protected band NOTE 6: N/A NOTE 7:Applicable when co-existence with PHS system operating in 1884.5 -1919.6MHz. NOTE 8:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. NOTE 9:N/A NOTE 10:N/A NOTE 11:Whether the applicable frequency range should be 793-805MHz instead of 799-805MHz is TBD NOTE 12:The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB NOTE 13:N/A NOTE 14: N/A NOTE 15:These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.3-1 from the edge of the channel bandwidth. NOTE 16: N/A NOTE 17: N/A NOTE 18: N/A NOTE 19:Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. NOTE 20:N/A NOTE21:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE22:This requirement is applicable for any channel bandwidths within the range 2570 – 2615 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2605.5 – 2607.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2597 – 2605 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. For carriers with channel bandwidth overlapping the frequency range 2615 – 2620 MHz the requirement applies with the maximum output power configured to +19 dBm in the IE P-Max. NOTE 23: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 24: As exceptions, measurements with a level up to the applicable requirement of -38 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 2^ndharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 2^nd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 25: As exceptions, measurements with a level up to the applicable requirement of -36 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 3^rdharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 3^rd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 26: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. NOTE 27: This requirement is applicable for any channel bandwidths within the range 1920 – 1980 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE 28: N/A NOTE 29: N/A NOTE 30: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz NOTE 31: N/A NOTE 32: Void NOTE 33: This requirement is only applicable for carriers with bandwidth confined within 1885-1920 MHz (requirement for carriers with at least 1RB confined within 1880 – 1885 MHz is not specified). This requirement applies for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1892.5 – 1894.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1895 – 1903 MHz. NOTE 34: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48. NOTE 35: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies. NOTE 36: This requirement is applicable for E-UTRA channel bandwidth allocated within 1920-1980 MHz. NOTE 37: Applicable when the upper edge of the channel bandwidth frequency is greater than 1980MHz. NOTE 38: Applicable only for UE category M1 and NB1. NOTE 39: For category NB1 UE when carrier centre frequency is 1920.1 MHz, in case of single-tone uplink transmission the requirement is applicable only for sub-carrier index > 2.

NOTE: The restriction on the maximum uplink transmission to 54 RB in Notes 21, 22, and 27 of Table 6.6.3.2.3-1E and the restriction on the single-tone uplink transmission to sub-carrier index > 2 in Note 39 of Table 6.6.3.2.3-1E are intended for conformance testing and may be applied to network operation to facilitate coexistence when the aggressor and victim bands are deployed in the same geographical area. The applicable spurious emission requirement of -15.5 dBm/5MHz is a least restrictive technical condition for FDD/TDD coexistence and may have to be revised in the future.

Table 6.6.3.2.3-1F: Spurious emission band UE co-existence limits Rel-14

E-UTRA Band	Spurious emission
	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
1	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 38, 40, 41, 42, 43, 44, 45, 65, 67, 68, 69	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	15
	Frequency range	1880		1895	-40	1	15, 27
	Frequency range	1895		1915	-15.5	5	15, 26, 27
	Frequency range	1915		1920	+1.6	5	15, 26, 27, 42
2	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 24, 26, 27, 28, 29, 30, 41, 42, 48, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
3	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 33, 34, 38, 39, 40, 41, 43, 44, 45, 65, 67, 68, 69	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3
4	E-UTRA Band 2, 4, 5, 7, 10, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 41, 43, 48, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
5	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 12, 13, 14, 17, 24, 25, 28, 29, 30, 31, 34, 38, 40, 42, 43, 45, 48, 65, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 26	859	–	869	-27	1
	E-UTRA Band 41	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 18, 19	F_{DL_low}	–	F_{DL_high}	-40	1	39
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	39
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 39
6	E-UTRA Band 1, 9, 11, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	875	-37	1
	Frequency range	875	–	895	-50	1
	Frequency range	1884.5	–	1919.6	-41	0.3	7
		1884.5	–	1915.7			8
7	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 12, 13, 14, 17, 20, 22, 26, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 65, 66, 67, 68	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2570	–	2575	+1.6	5	15, 21, 26
	Frequency range	2575	–	2595	-15.5	5	15, 21, 26
	Frequency range	2595	–	2620	-40	1	15, 21
8	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40, 45, 65, 67, 68, 69	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3, 7, 22, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	23
	Frequency range	860	–	890	-40	1	15, 23
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 23
9	E-UTRA Band 1, 3, 11, 18, 19, 21, 26, 28, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
10	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 41, 43, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
11	E-UTRA Band 1, 3, 11, 18, 19, 21, 28, 34, 40, 42, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
12	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 26, 27, 30, 41, 48,	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	15
13	E-UTRA Band 2, 4, 5, 10, 12, 13, 17, 25, 26, 27, 29, 41, 48, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 14	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 24, 30	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	769	–	775	-35	0.00625	15
	Frequency range	799	–	805	-35	0.00625	11, 15
14	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 23, 24, 25, 26, 27, 29, 30, 41, 48, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	769	–	775	-35	0.00625	12, 15
	Frequency range	799	–	805	-35	0.00625	11, 12, 15
17	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 26, 27, 30, 41, 48	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	15
18	E-UTRA Band 1, 3, 11, 21, 34, 40, 42, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	758	–	799	-50	1
	Frequency range	799	–	803	-40	1	15
	Frequency range	860	–	890	-40	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
19	E-UTRA Band 1, 3, 11, 21, 28, 34, 40, 42, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
20	E-UTRA Band 1, 3, 7, 8, 22, 31, 32, 33, 34, 40, 43, 65, 67, 68	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 38, 42, 69	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	758	–	788	-50	1
21	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 42, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
22	E-UTRA Band 1, 3, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 39, 40, 43, 65, 67, 68, 69	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	3510	–	3525	-40	1	15
	Frequency range	3525	–	3590	-50	1
23	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 23, 24, 26, 27, 29, 30, 41, 66	F_{DL_low}	–	F_{DL_high}	-50	1
24	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 48, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
25	E-UTRA Band 4, 5, 10,12, 13, 14, 17, 24, 26, 27, 28, 29, 30, 41, 42, 48, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 25	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
26	E-UTRA Band 1, 2, 3, 4, 5, 10, 11, 12, 13, 14, 17, 18,19, 21, 24, 25, 26, 29, 30, 31, 34, 39, 40, 42, 43, 48, 65, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 41	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	703	–	799	-50	1
	Frequency range	799	–	803	-40	1	15
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
27	E-UTRA Band 1, 2, 3, 4, 5, 7, 10, 12, 13, 14, 17, 25, 26, 27, 29, 30, 31, 38, 40, 41, 42, 43, 65, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 28	F_{DL_low}	–	790	-50	1
	Frequency range	799	–	805	-35	0.00625
28	E-UTRA Band 1, 4, 10, 22, 42, 43, 65, 66	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}	–	F_{DL_high}	-50	1	19, 25
	E-UTRA Band 2, 3, 5, 7, 8, 18, 19, 20, 25, 26, 27, 31, 34, 38, 40, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	19, 24
	Frequency range	470	–	694	-42	8	15, 35
	Frequency range	470	–	710	-26.2	6	34
	Frequency range	662	–	694	-26.2	6	15
	Frequency range	758	–	773	-32	1	15
	Frequency range	773	–	803	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 19
30	E-UTRA Band 2, 4, 5, 7, 10, 12, 13, 14, 17, 24, 25, 26, 27, 29, 30, 38, 41, 48, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
31	E-UTRA Band 1, 5, 7, 8, 20, 22, 26, 27, 28, 31, 32, 33, 34, 38, 40, 42, 43, 65, 67, 68, 69	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	470	–	694	-42	8
…
33	E-UTRA Band 1, 7, 8, 20, 22, 28, 31, 32, 34, 38, 40, 42, 43, 65, 67, 69	F_{DL_low}	–	F_{DL_high}	-50	1	5
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
34	E-UTRA Band 1, 3, 7, 8, 11, 18, 19, 20, 21, 22, 26, 28, 31, 32, 33, 38,39, 40, 41, 42, 43, 44, 45, 65, 67, 69	F_{DL_low}	–	F_{DL_high}	-50	1	5
	Frequency range	1884.5	–	1915.7	-41	0.3	8
35
36
37			–
38	E-UTRA Band 1, 2, 3, 4, 5, 8, 10, 12, 13, 14, 17, 20, 22, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 65, 66, 67, 68	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2620	–	2645	-15.5	5	15, 22, 26
	Frequency range	2645	–	2690	-40	1	15, 22
39	E-UTRA Band 1, 8, 22, 26, 34, 40, 41, 42, 44, 45	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1805		1855	-40	1	33
	Frequency range	1855		1880	-15.5	5	15,26,33
40	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 33, 34, 38, 39, 41, 42, 43, 44, 45, 65, 67, 68, 69	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	1475	–	1518	-50	1
	Frequency range	3300	–	4200	-50	1
	Frequency range	4400	–	5000	-50	1	2
41	E-UTRA Band 1, 2, 3, 4, 5, 8, 10, 12, 13 , 14, 17, 24, 25, 26, 27, 28, 29, 30, 34, 39, 40, 42, 44, 45, 48, 65, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	30
	Frequency range	1884.5		1915.7	-41	0.3	8, 30
42	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 11, 18, 19, 20, 21, 25, 26, 27, 28, 31, 32, 33, 34, 38, 40, 41, 44, 45, 65, 66, 67, 68, 69	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
43	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 20, 25, 26, 27, 28, 31,32, 33, 34, 38, 40, 65, 66, 67, 68, 69	F_{DL_low}	–	F_{DL_high}	-50	1
44	E-UTRA Band 1, 40, 42, 45	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 3, 5, 8, 34, 39, 41	F_{DL_low}	–	F_{DL_high}	-50	1
45	E-UTRA Band 1, 3, 5, 8, 34, 39, 40, 41, 42.44	F_{DL_low}	–	F_{DL_high}	-50	1
…
47	E-UTRA Band 1, 3, 5, 7, 8, 22, 26, 28, 34, 39, 40, 41, 42, 44, 45, 65, 68	FDL_low	–	FDL_high	-50	1
	Frequency range	5925	–	5950	-30 EIRP	1	38, 40, 41
	Frequency range	5815	–	5855	-30 EIRP	1	38, 41, 43

48	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 66, 70	FD_{L_low}	–	FD_{L_high}	-50	1
65	E-UTRA Band 1, 3, 7, 8, 20, 22, 28, 31, 32, 38, 40, 42, 43, 65, 68, 69	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 5, 11, 18, 19, 21, 26, 27, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	36
	Frequency range	1884.5	–	1915.7	-41	0.3	37
	Frequency range	1900	–	1915	-15.5	5	15, 26, 27
	Frequency range	1915	–	1920	+1.6	5	15, 26, 27
66	E-UTRA Band 2, 4, 5, 7, 10, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 38, 41, 43, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42, 48	F_{DL_low}	–	F_{DL_high}	-50	1	2
68	E-UTRA Band 3, 7, 8, 20, 22, 28, 31, 38, 40, 42, 43, 47, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 1	F_{DL_low}	–	F_{DL_high}	-50	1	2
…
70	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 48, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1	2
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2: As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1.3-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th [or 5^th] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3: N/A NOTE 4: N/A NOTE 5: For non-synchronised TDD operation to meet these requirements some restriction will be needed for either the operating band or protected band NOTE 6: N/A NOTE 7:Applicable when co-existence with PHS system operating in 1884.5 -1919.6MHz. NOTE 8:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. NOTE 9:N/A NOTE 10:N/A NOTE 11:Whether the applicable frequency range should be 793-805MHz instead of 799-805MHz is TBD NOTE 12:The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB NOTE 13:N/A NOTE 14: N/A NOTE 15:These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.3-1 from the edge of the channel bandwidth. NOTE 16: N/A NOTE 17: N/A NOTE 18: N/A NOTE 19:Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. NOTE 20:N/A NOTE21:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE22:This requirement is applicable for any channel bandwidths within the range 2570 – 2615 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2605.5 – 2607.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2597 – 2605 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. For carriers with channel bandwidth overlapping the frequency range 2615 – 2620 MHz the requirement applies with the maximum output power configured to +19 dBm in the IE P-Max. NOTE 23: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 24: As exceptions, measurements with a level up to the applicable requirement of -38 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 2^ndharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.4.2-1) for which the 2^nd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 25: As exceptions, measurements with a level up to the applicable requirement of -36 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 3^rdharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.4.2-1) for which the 3^rd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 26: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. NOTE 27: This requirement is applicable for any channel bandwidths within the range 1920 – 1980 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE 28: N/A NOTE 29: N/A NOTE 30: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz NOTE 31: N/A NOTE 32: Void NOTE 33: This requirement is only applicable for carriers with bandwidth confined within 1885-1920 MHz (requirement for carriers with at least 1RB confined within 1880 – 1885 MHz is not specified). This requirement applies for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1892.5 – 1894.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1895 – 1903 MHz. NOTE 34: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48. NOTE 35: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies. NOTE 36: This requirement is applicable for E-UTRA channel bandwidth allocated within 1920-1980 MHz. NOTE 37: Applicable when the upper edge of the channel bandwidth frequency is greater than 1980MHz. NOTE 38: Applicable when NS_33 or NS_34 is configured by the pre-configured radio parameters. NOTE 39: Applicable only when the assigned E-UTRA carrier is confined within 824 MHz and 849 MHz for UE category M1, M2 and UE category NB1 and NB2. NOTE 40: In the frequency range x-5950MHz, SE requirement of -30dBm/MHz should be applied; where x = max (5925, fc + 15), where fc is the channel centre frequency. NOTE 41: The EIRP requirement is converted to conducted requirement depend on the supported post antenna connector gain G_{post connector} declared by the UE following the principle described in annex I. NOTE 42: For category NB1 and NB2 UE when carrier centre frequency is 1920.1 MHz, in case of single-tone uplink transmission the requirement is applicable only for sub-carrier index > 2. NOTE 43: Resolution BW is 10% of the measurement BW and the result should be integrated to achieve the measurement bandwidth. The sweep time shall be set at least as (sweep points)*(symbol length) to improve the measurement accuracy.

NOTE: The restriction on the maximum uplink transmission to 54 RB in Notes 21, 22, and 27 of Table 6.6.3.2.3-1F and the restriction on the single-tone uplink transmission to sub-carrier index > 2 in Note 42 of Table 6.6.3.2.3-1F are intended for conformance testing and may be applied to network operation to facilitate coexistence when the aggressor and victim bands are deployed in the same geographical area. The applicable spurious emission requirement of -15.5 dBm/5MHz is a least restrictive technical condition for FDD/TDD coexistence and may have to be revised in the future.

Table 6.6.3.2.3-1G: Spurious emission band UE co-existence limits Rel-15

E-UTRA Band	Spurious emission
	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
1	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 38, 40, 41, 42, 43, 44, 45, 50, 51, 52, 65, 67, 68, 69, 72, 73, 74, 75, 76 NR Band n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	15
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1880		1895	-40	1	15, 27
	Frequency range	1895		1915	-15.5	5	15, 26, 27
	Frequency range	1915		1920	+1.6	5	15, 26, 27, 44
2	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 27, 28, 29, 30, 41, 42, 48, 50, 51, 66, 70, 71, 74, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
3	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 33, 34, 38, 39, 40, 41, 43, 44, 45, 50, 51, 65, 67, 68, 69, 72, 73,74, 75, 76 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 22, 42, 52 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3
4	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 41, 43, 48, 50, 51, 66, 70, 71, 74, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
5	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 24, 25, 28, 29, 30, 31, 34, 38, 40, 42, 43, 45, 48, 50, 51, 65, 66, 70, 71, 73, 74, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 26	859	–	869	-27	1
	E-UTRA Band 41, 52 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 18, 19	F_{DL_low}	–	F_{DL_high}	-40	1	39
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	39
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 39
6	E-UTRA Band 1, 9, 11, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	875	-37	1
	Frequency range	875	–	895	-50	1
	Frequency range	1884.5	–	1919.6	-41	0.3	7
		1884.5	–	1915.7			8
7	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 20, 22, 26, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 50, 51, 52, 65, 66, 67, 68, 72, 74, 75, 76, 85 NR Band n77,n78	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2570	–	2575	+1.6	5	15, 21, 26
	Frequency range	2575	–	2595	-15.5	5	15, 21, 26
	Frequency range	2595	–	2620	-40	1	15, 21
8	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40, 45, 50, 51, 65, 67, 68, 69, 72, 73, 74, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3, 7, 22, 41, 42, 43, 52 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	23
	Frequency range	860	–	890	-40	1	15, 23
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 23
9	E-UTRA Band 1, 3, 11, 18, 19, 21, 26, 28, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
10	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 41, 43, 66, 70, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
11	E-UTRA Band 1, 3, 11, 18, 19, 21, 28, 34, 40, 42, 65 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	945	–	960	-50	1

	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
12	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 26, 27, 30, 41, 70, 71, 74	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 48, 50, 51, 66	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 85	F_{DL_low}	–	F_{DL_high}	-50	1	15
13	E-UTRA Band 2, 4, 5, 12, 13, 17, 25, 26, 27, 29, 41, 48, 50, 51, 66, 70, 71, 74, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 14	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 24, 30	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	769	–	775	-35	0.00625	15
	Frequency range	799	–	805	-35	0.00625	15
14	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 23, 24, 25, 26, 27, 29, 30, 41, 48, 66, 70, 71, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	769	–	775	-35	0.00625	12, 15
	Frequency range	799	–	805	-35	0.00625	12, 15
17	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 26, 27, 30, 41, 70, 71, 74	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 48, 50, 51, 66	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 85	F_{DL_low}	–	F_{DL_high}	-50	1	15
18	E-UTRA Band 1, 3, 11, 21, 34, 40, 42, 65 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	758	–	799	-50	1
	Frequency range	799	–	803	-40	1	15
	Frequency range	860	–	890	-40	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
19	E-UTRA Band 1, 3, 11, 21, 28, 34, 40, 42, 65 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
20	E-UTRA Band 1, 3, 7, 8, 22, 31, 32, 33, 34, 40, 43, 50, 51, 65, 67, 68, 72, 74, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 38, 42, 52, 69 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	758	–	788	-50	1
21	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 42, 65 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
22	E-UTRA Band 1, 3, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 39, 40, 43, 65, 67, 68, 69, 72, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	3510	–	3525	-40	1	15
	Frequency range	3525	–	3590	-50	1
23	E-UTRA Band 4, 5, 12, 13, 14, 17, 23, 24, 26, 27, 29, 30, 41, 66	F_{DL_low}	–	F_{DL_high}	-50	1
24	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 48, 66, 70, 71, 85	F_{DL_low}	–	F_{DL_high}	-50	1
25	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 27, 28, 29, 30, 41, 42, 48, 66, 70, 71, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 25	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
26	E-UTRA Band 1, 2, 3, 4, 5, 11, 12, 13, 14, 17, 18,19, 21, 24, 25, 26, 29, 30, 31, 34, 39, 40, 42, 43, 48, 50, 51, 65, 66, 70, 71, 73,74, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 41 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	703	–	799	-50	1
	Frequency range	799	–	803	-40	1	15
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
27	E-UTRA Band 1, 2, 3, 4, 5, 7, 12, 13, 14, 17, 25, 26, 27, 29, 30, 31, 38, 40, 41, 42, 43, 65, 66, 73, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 28	F_{DL_low}	–	790	-50	1
	Frequency range	799	–	805	-35	0.00625
28	E-UTRA Band 1, 4, 22, 32, 42, 43, 50, 51, 65, 66, 73, 74, 75, 76 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}	–	F_{DL_high}	-50	1	19, 25
	E-UTRA Band 2, 3, 5, 7, 8, 18, 19, 20, 25, 26, 27, 31, 34, 38, 40, 41, 52, 72 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	19, 24
	Frequency range	470	–	694	-42	8	15, 35
	Frequency range	470	–	710	-26.2	6	34
	Frequency range	662	–	694	-26.2	6	15
	Frequency range	758	–	773	-32	1	15
	Frequency range	773	–	803	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 19
30	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 24, 25, 26, 27, 29, 30, 38, 41, 48, 66, 70, 71, 85	F_{DL_low}	–	F_{DL_high}	-50	1
31	E-UTRA Band 1, 5, 7, 8, 20, 22, 26, 27, 28, 31, 32, 33, 34, 38, 40, 42, 43, 50, 51, 52, 65, 67, 68, 69, 74, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	470	–	694	-42	8
…
33	E-UTRA Band 1, 7, 8, 20, 22, 28, 31, 32, 34, 38, 40, 42, 43, 52, 65, 67, 69, 72, 73, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1	5
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
34	E-UTRA Band 1, 3, 7, 8, 11, 18, 19, 20, 21, 22, 26, 28, 31, 32, 33, 38,39, 40, 41, 42, 43, 44, 45, 50, 51, 52, 65, 67, 69, 72, 73, 74, 75, 76 NR Band n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1	5
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2, 5
	Frequency range	1884.5	–	1915.7	-41	0.3	8
35
36
37			–
38	E-UTRA Band 1, 2, 3, 4, 5, 8, 12, 13, 14, 17, 20, 22, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 50, 51, 52, 65, 66, 67, 68, 72, 74, 75, 76, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2620	–	2645	-15.5	5	15, 22, 26
	Frequency range	2645	–	2690	-40	1	15, 22
39	E-UTRA Band 1, 8, 22, 26, 34, 40, 41, 42, 44, 45, 50, 51, 52, 73, 74 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1805		1855	-40	1	33
	Frequency range	1855		1880	-15.5	5	15,26,33
40	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 33, 34, 38, 39, 41, 42, 43, 44, 45, 50, 51, 52, 65, 67, 68, 69, 72, 73, 74, 75, 76 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		1915.7	-41	0.3	8
41	E-UTRA Band 1, 2, 3, 4, 5, 8, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 34, 39, 40, 42, 44, 45, 48, 50, 51, 52, 65, 66, 70, 71, 73, 74, 85 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	30
	NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		1915.7	-41	0.3	8, 30
42	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 11, 18, 19, 20, 21, 25, 26, 27, 28, 31, 32, 33, 34, 38, 40, 41, 44, 45, 50, 51, 65, 66, 67, 68, 69, 72, 73, 74, 75, 76 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
43	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 20, 25, 26, 27, 28, 31,32, 33, 34, 38, 40, 50, 51, 65, 66, 67, 68, 69, 72, 73, 74, 75, 76, 85	F_{DL_low}	–	F_{DL_high}	-50	1
44	E-UTRA Band 1, 40, 42, 45	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 3, 5, 8, 34, 39, 41, 73	F_{DL_low}	–	F_{DL_high}	-50	1
45	E-UTRA Band 1, 3, 5, 8, 34, 39, 40, 41, 42, 44, 52, 73	F_{DL_low}	–	F_{DL_high}	-50	1
…
47	E-UTRA Band 1, 3, 5, 7, 8, 22, 26, 28, 34, 39, 40, 41, 42, 44, 45, 65, 68, 72, 73 NR band n77, n78 , n79	FDL_low	–	FDL_high	-50	1
	Frequency range	5925	–	5950	-30 EIRP	1	38, 40, 43
	Frequency range	5815	–	5855	-30 EIRP	1	38, 43, 45
48	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 50, 51, 66, 70, 71, 74, 85	FD_{L_low}	–	FD_{L_high}	-50	1
50	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 20, 26, 28, 29, 31, 34, 38, 39, 40, 41, 42, 43, 48, 52, 65, 66, 67, 68, 85	F_{DL_low}	–	F_{DL_high}	-50	1
51	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 20, 26, 28, 29, 31, 34, 38, 39, 40, 41, 42, 43, 48, 52, 65, 66, 67, 68, 85	F_{DL_low}	–	F_{DL_high}	-50	1
52	E-UTRA Band 1, 3, 5, 7, 8, 20, 28, 31, 33, 34, 38, 39, 40, 41, 45, 47, 50, 51, 68, 72, 73, 74	F_{DL_low}	–	F_{DL_high}	-50	1
65	E-UTRA Band 1, 3, 7, 8, 20, 22, 28, 31, 32, 38, 40, 42, 43, 50, 51, 65, 68, 69, 72, 74, 75, 76 NR Band , n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 5, 11, 18, 19, 21, 26, 27, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	36
	Frequency range	1884.5	–	1915.7	-41	0.3	37
	Frequency range	1900	–	1915	-15.5	5	15, 26, 27
	Frequency range	1915	–	1920	+1.6	5	15, 26, 27
66	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 38, 41, 43, 50, 51, 66, 70, 71, 74, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42, 48	F_{DL_low}	–	F_{DL_high}	-50	1	2
68	E-UTRA Band 3, 7, 8, 20, 28, 31, 38, 40, 47, 72, 74	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 1, 11, 42, 43, 50, 51, 52, 65	F_{DL_low}	–	F_{DL_high}	-50	1	2
…
70	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 48, 66, 70, 71, 85	F_{DL_low}	–	F_{DL_high}	-50	1
71	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 30, 48, 66, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25, 41, 70	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 29	F_{DL_low}	–	F_{DL_high}	-38	1	15
	E-UTRA Band 71	F_{DL_low}	–	F_{DL_high}	-50	1	15
72	E-UTRA Band 1, 7, 20, 22, 28, 31, 32, 33, 34, 38, 42, 43, 47, 52, 65, 68, 72	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3, 8, 40	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	470	–	694	-42	8
73	E-UTRA Band 1, 26, 28, 33, 34, 39, 41, 42, 43, 44, 45, 47, 52	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3, 5, 8, 27, 40	F_{DL_low}	–	F_{DL_high}	-50	1	2
74	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 18, 19, 20, 26, 28, 29, 31, 34, 38, 39, 40, 41, 42, 43, 48, 52, 65, 66, 67, 68, 85 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	1400	–	1427	-32	27	15, 41
	Frequency range	1475	–	1488	-50	1	42
	Frequency range	1488	–	1518	-50	1	15
85	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 26, 27, 30, 41, 70, 71, 74	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 48, 51, 66	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 85	F_{DL_low}	–	F_{DL_high}	-50	1	15
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2: As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th [or 5^th] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3: N/A NOTE 4: N/A NOTE 5: For non-synchronised TDD operation to meet these requirements some restriction will be needed for either the operating band or protected band NOTE 6: N/A NOTE 7:Applicable when co-existence with PHS system operating in 1884.5 -1919.6MHz. NOTE 8:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. NOTE 9:N/A NOTE 10:N/A NOTE 11: Void NOTE 12:The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB NOTE 13:N/A NOTE 14: N/A NOTE 15:These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the channel bandwidth. NOTE 16: N/A NOTE 17: N/A NOTE 18: N/A NOTE 19:Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. NOTE 20:N/A NOTE21:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE22:This requirement is applicable for power class 3 UE for any channel bandwidths within the range 2570 – 2615 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2605.5 – 2607.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2597 – 2605 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. For power class 2 UE for any channel bandwidths within the range 2570 – 2615 MHz, NS_44 shall apply. For power class 2 or 3 UE for carriers with channel bandwidth overlapping the frequency range 2615 – 2620 MHz the requirement applies with the maximum output power configured to +19 dBm in the IE P-Max. NOTE 23: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 24: As exceptions, measurements with a level up to the applicable requirement of -38 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 2^ndharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 2^nd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 25: As exceptions, measurements with a level up to the applicable requirement of -36 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 3^rdharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 3^rd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 26: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. NOTE 27: This requirement is applicable for any channel bandwidths within the range 1920 – 1980 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE 28: N/A NOTE 29: N/A NOTE 30: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz NOTE 31: N/A NOTE 32: Void NOTE 33: This requirement is only applicable for carriers with bandwidth confined within 1885-1920 MHz (requirement for carriers with at least 1RB confined within 1880 – 1885 MHz is not specified). This requirement applies for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1892.5 – 1894.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1895 – 1903 MHz. NOTE 34: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48. NOTE 35: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies. NOTE 36: This requirement is applicable for E-UTRA channel bandwidth allocated within 1920-1980 MHz. NOTE 37: Applicable when the upper edge of the channel bandwidth frequency is greater than 1980MHz. NOTE 38: Applicable when NS_33 or NS_34 is configured by the pre-configured radio parameters. NOTE 39: Applicable only when the assigned E-UTRA carrier is confined within 824 MHz and 849 MHz for UE category M1, M2 and UE category NB1 and NB2. NOTE 40: In the frequency range x-5950MHz, SE requirement of -30dBm/MHz should be applied; where x = max (5925, fc + 15), where fc is the channel centre frequency. NOTE 41: Applicable for all bandwidths, and when the lower edge of the assigned E-UTRA UL channel bandwidth frequency is greater than or equal to 1427 MHz + the channel BW assigned for 1.4, 3, 5 and 10 MHz bandwidth, and when the lower edge of the assigned E-UTRA UL channel bandwidth frequency is greater than or equal to 1440 MHz for 15 and 20 MHz bandwidth. This requirement shall be verified with UE transmission power of 15 dBm. NOTE 42: Applicable for 1.4 , 3 and 5 MHz bandwidth, and when the upper edge of the assigned E-UTRA UL channel bandwidth frequency is less than or equal to 1467 MHz assigned for10 MHz bandwidth, and when the upper edge of the assigned E-UTRA UL channel bandwidth frequency is less than or equal to 1463.8 MHz for 15 MHz bandwidth, and when the upper edge of the assigned E-UTRA UL channel bandwidth frequency is less than or equal to 1460.8 MHz for 20 MHz bandwidth. NOTE 43: The EIRP requirement is converted to conducted requirement depend on the supported post antenna connector gain G_{post connector} declared by the UE following the principle described in annex I. NOTE 44: For category NB1 and NB2 UE when carrier centre frequency is 1920.1 MHz, in case of single-tone uplink transmission the requirement is applicable only for sub-carrier index > 2. NOTE 45: Resolution BW is 10% of the measurement BW and the result should be integrated to achieve the measurement bandwidth. The sweep time shall be set at least as (sweep points)*(symbol length) to improve the measurement accuracy.

NOTE: The restriction on the maximum uplink transmission to 54 RB in Notes 21, 22, and 27 of Table 6.6.3.2.3-1G and the restriction on the single-tone uplink transmission to sub-carrier index > 2 in Note 44 of Table 6.6.3.2.3-1G are intended for conformance testing and may be applied to network operation to facilitate coexistence when the aggressor and victim bands are deployed in the same geographical area. The applicable spurious emission requirement of -15.5 dBm/5MHz is a least restrictive technical condition for FDD/TDD coexistence and may have to be revised in the future.

The normative reference for this requirement is TS 36.101 [2] subclause 6.6.3.2.

This test use minimum requirements from many releases of TS 36.101 [2] due to release independence defined in TS 36.307 [16]

Table 6.6.3.2.3-1H: Spurious emission band UE co-existence limits Rel-16

E-UTRA Band	Spurious emission
E-UTRA Band	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
1	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 38, 40, 41, 42, 43, 44, 45, 50, 51, 52, 65, 67, 68, 69, 72, 73, 74, 75, 76, 87, 88 NR Band n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	15
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1880		1895	-40	1	15, 27
	Frequency range	1895		1915	-15.5	5	15, 26, 27
	Frequency range	1915		1920	+1.6	5	15, 26, 27, 44
2	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 27, 28, 29, 30, 41, 42, 48, 50, 51, 53, 66, 70, 71, 74, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25,	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43 NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
3	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 33, 34, 38, 39, 40, 41, 43, 44, 45, 50, 51, 65, 67, 68, 69, 72, 73,74, 75, 76, 87, 88 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 22, 42, 52 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3
4	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 41, 43, 48, 50, 51, 53, 66, 70, 71, 74, 85	F_{DL_low}	–	F_{DL_high}	-50	1
4	E-UTRA Band 42, NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
5	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 24, 25, 28, 29, 30, 31, 34, 38, 40, 42, 43, 45, 48, 50, 51, 65, 66, 70, 71, 73, 74, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 26	859	–	869	-27	1
	E-UTRA Band 41, 52, 53 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 18, 19	F_{DL_low}	–	F_{DL_high}	-40	1	39
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	39
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 39
6	E-UTRA Band 1, 9, 11, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	875	-37	1
	Frequency range	875	–	895	-50	1
	Frequency range	1884.5	–	1919.6	-41	0.3	7
	Frequency range	1884.5	–	1915.7	-41	0.3	8
7	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 20, 22, 26, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 50, 51, 52, 65, 66, 67, 68, 72, 74, 75, 76, 85, 87, 88 NR Band n77,n78	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2570	–	2575	+1.6	5	15, 21, 26
	Frequency range	2575	–	2595	-15.5	5	15, 21, 26
	Frequency range	2595	–	2620	-40	1	15, 21
8	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40, 45, 50, 51, 65, 67, 68, 69, 72, 73, 74, 75, 76, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3, 7, 22, 41, 42, 43, 52 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	23
	Frequency range	860	–	890	-40	1	15, 23
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 23
9	E-UTRA Band 1, 3, 11, 18, 19, 21, 26, 28, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
10	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 41, 43, 66, 70, 85	F_{DL_low}	–	F_{DL_high}	-50	1
10	E-UTRA Band 22, 42, NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
11	E-UTRA Band 1, 3, 11, 18, 19, 21, 28, 34, 40, 42, 65 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	945	–	960	-50	1

	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
12	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 26, 27, 30, 41, 53, 70, 71, 74	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 48, 50, 51, 66 NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 85	F_{DL_low}	–	F_{DL_high}	-50	1	15
13	E-UTRA Band 2, 4, 5, 12, 13, 17, 25, 26, 27, 29, 41, 48, 50, 51, 53, 66, 70, 71, 74, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 14	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 24, 30, NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	769	–	775	-35	0.00625	15
	Frequency range	799	–	805	-35	0.00625	15
14	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 23, 24, 25, 26, 27, 29, 30, 41, 48, 53, 66, 70, 71, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	769	–	775	-35	0.00625	12, 15
	Frequency range	799	–	805	-35	0.00625	12, 15
17	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 26, 27, 30, 41, 70, 71, 74	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 50, 51, 53, 66 NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 48, 85	F_{DL_low}	–	F_{DL_high}	-50	1	15
18	E-UTRA Band 1, 3, 11, 21, 34, 40, 42, 65 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	758	–	799	-50	1
	Frequency range	799	–	803	-40	1	15
	Frequency range	860	–	890	-40	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
19	E-UTRA Band 1, 3, 11, 21, 28, 34, 40, 42, 65 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
20	E-UTRA Band 1, 3, 7, 8, 22, 31, 32, 33, 34, 40, 43, 50, 51, 65, 67, 68, 72, 74, 75, 76, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 38, 42, 52, 69 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	758	–	788	-50	1
21	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 42, 65 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
22	E-UTRA Band 1, 3, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 39, 40, 43, 65, 67, 68, 69, 72, 75, 76, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	3510	–	3525	-40	1	15
	Frequency range	3525	–	3590	-50	1
23	E-UTRA Band 4, 5, 12, 13, 14, 17, 23, 24, 26, 27, 29, 30, 41, 66	F_{DL_low}	–	F_{DL_high}	-50	1
24	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 48, 66, 70, 71, 85	F_{DL_low}	–	F_{DL_high}	-50	1
24	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
25	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 27, 28, 29, 30, 41, 42, 48, 53, 66, 70, 71, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 25	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43, NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
26	E-UTRA Band 1, 2, 3, 4, 5, 11, 12, 13, 14, 17, 18,19, 21, 24, 25, 26, 29, 30, 31, 34, 39, 40, 42, 43, 48, 50, 51, 65, 66, 70, 71, 73,74, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 41, 53 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	703	–	799	-50	1
	Frequency range	799	–	803	-40	1	15
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
27	E-UTRA Band 1, 2, 3, 4, 5, 7, 12, 13, 14, 17, 25, 26, 27, 29, 30, 31, 38, 40, 41, 42, 43, 65, 66, 73, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 28	F_{DL_low}	–	790	-50	1
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	799	–	805	-35	0.00625
28	E-UTRA Band 1, 4, 22, 32, 42, 43, 50, 51, 65, 66, 73, 74, 75, 76 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}	–	F_{DL_high}	-50	1	19, 25
	E-UTRA Band 2, 3, 5, 7, 8, 18, 19, 20, 25, 26, 27, 31, 34, 38, 40, 41, 52, 72, 87, 88 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	19, 24
	Frequency range	470	–	694	-42	8	15, 35
	Frequency range	470	–	710	-26.2	6	34
	Frequency range	662	–	694	-26.2	6	15
	Frequency range	758	–	773	-32	1	15
	Frequency range	773	–	803	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 19
30	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 24, 25, 26, 27, 29, 30, 38, 41, 48, 53, 66, 70, 71, 85	F_{DL_low}	–	F_{DL_high}	-50	1
30	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
31	E-UTRA Band 1, 5, 7, 8, 20, 22, 26, 27, 28, 31, 32, 33, 34, 38, 40, 42, 43, 50, 51, 52, 65, 67, 68, 69, 74, 75, 76, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	470	–	694	-42	8
…
33	E-UTRA Band 1, 7, 8, 20, 22, 28, 31, 32, 34, 38, 40, 42, 43, 52, 65, 67, 69, 72, 73, 75, 76, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1	5
33	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
34	E-UTRA Band 1, 3, 7, 8, 11, 18, 19, 20, 21, 22, 26, 28, 31, 32, 33, 38,39, 40, 41, 42, 43, 44, 45, 50, 51, 52, 65, 67, 69, 72, 73, 74, 75, 76, 87, 88 NR Band n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1	5
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2, 5
	Frequency range	1884.5	–	1915.7	-41	0.3	8
35
36
37			–
38	E-UTRA Band 1, 2, 3, 4, 5, 8, 12, 13, 14, 17, 20, 22, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 50, 51, 52, 65, 66, 67, 68, 72, 74, 75, 76, 85, 87, 88 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2620	–	2645	-15.5	5	15, 22, 26
	Frequency range	2645	–	2690	-40	1	15, 22
39	E-UTRA Band 1, 8, 22, 26, 28, 34, 40, 41, 42, 44, 45, 50, 51, 52, 73, 74 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1805		1855	-40	1	33
	Frequency range	1855		1880	-15.5	5	15,26,33
40	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 33, 34, 38, 39, 41, 42, 43, 44, 45, 50, 51, 52, 65, 67, 68, 69, 72, 73, 74, 75, 76, 87, 88 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	8
41	E-UTRA Band 1, 2, 3, 4, 5, 8, 12, 13 , 14, 17, 24, 25, 26, 27, 28, 29, 30, 34, 39, 40, 42, 44, 45, 48, 50, 51, 52, 65, 66, 70, 71, 73, 74, 85 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	30
	NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		1915.7	-41	0.3	8, 30
42	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 11, 18, 19, 20, 21, 25, 26, 27, 28, 31, 32, 33, 34, 38, 40, 41, 44, 45, 50, 51, 65, 66, 67, 68, 69, 72, 73, 74, 75, 76, 87, 88 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
42	Frequency range	1884.5	–	1915.7	-41	0.3	8
43	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 20, 25, 26, 27, 28, 31,32, 33, 34, 38, 40, 50, 51, 65, 66, 67, 68, 69, 72, 73, 74, 75, 76, 85, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
44	E-UTRA Band 1, 40, 42, 45	F_{DL_low}	–	F_{DL_high}	-50	1	2
44	E-UTRA Band 3, 5, 8, 34, 39, 41, 73	F_{DL_low}	–	F_{DL_high}	-50	1
45	E-UTRA Band 1, 3, 5, 8, 34, 39, 40, 41, 42, 44, 52, 73	F_{DL_low}	–	F_{DL_high}	-50	1
…
47	E-UTRA Band 1, 3, 5, 7, 8, 22, 26, 28, 34, 39, 40, 41, 42, 44, 45, 65, 68, 72, 73 NR band n77, n78 , n79	FDL_low	–	FDL_high	-50	1
	Frequency range	5925	–	5950	-30 EIRP	1	38, 40, 43
	Frequency range	5815	–	5855	-30 EIRP	1	38, 43, 45
48	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 50, 51, 66, 70, 71, 74, 85	FD_{L_low}	–	FD_{L_high}	-50	1
50	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 20, 26, 28, 29, 31, 34, 38, 39, 40, 41, 42, 43, 48, 52, 65, 66, 67, 68, 85	F_{DL_low}	–	F_{DL_high}	-50	1
51	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 20, 26, 28, 29, 31, 34, 38, 39, 40, 41, 42, 43, 48, 52, 65, 66, 67, 68, 85	F_{DL_low}	–	F_{DL_high}	-50	1
52	E-UTRA Band 1, 3, 5, 7, 8, 20, 28, 31, 33, 34, 38, 39, 40, 41, 45, 47, 50, 51, 68, 72, 73, 74, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
53	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 48, 66, 70, 71, 85, NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1
65	E-UTRA Band 1, 3, 7, 8, 20, 22, 28, 31, 32, 38, 40, 42, 43, 50, 51, 65, 68, 69, 72, 74, 75, 76, 87, 88 NR Band n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 5, 11, 18, 19, 21, 26, 27, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	36
	Frequency range	1884.5	–	1915.7	-41	0.3	37
	Frequency range	1900	–	1915	-15.5	5	15, 26, 27
	Frequency range	1915	–	1920	+1.6	5	15, 26, 27
66	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 38, 41, 43, 50, 51, 53, 66, 70, 71, 74, 85	F_{DL_low}	–	F_{DL_high}	-50	1
66	E-UTRA Band 42, 48, NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
68	E-UTRA Band 3, 7, 8, 20, 28, 31, 38, 40, 47, 72, 74, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
68	E-UTRA Band 1, 22, 42, 43, 50, 51, 52, 65	F_{DL_low}	–	F_{DL_high}	-50	1	2
…
70	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 48, 53, 66, 70, 71, 85	F_{DL_low}	–	F_{DL_high}	-50	1
70	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
71	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 30, 48, 53, 66, 85	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25, 41, 70, NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 29	F_{DL_low}	–	F_{DL_high}	-38	1	15
	E-UTRA Band 71	F_{DL_low}	–	F_{DL_high}	-50	1	15
72	E-UTRA Band 1, 7, 20, 22, 28, 31, 32, 33, 34, 38, 42, 43, 47, 52, 65, 68, 72, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3, 8, 40	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	470	–	694	-42	8
73	E-UTRA Band 1, 26, 28, 33, 34, 39, 41, 42, 43, 44, 45, 47, 52	F_{DL_low}	–	F_{DL_high}	-50	1
73	E-UTRA Band 3, 5, 8, 27, 40	F_{DL_low}	–	F_{DL_high}	-50	1	2
74	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 18, 19, 20, 26, 28, 29, 31, 34, 38, 39, 40, 41, 42, 43, 48, 52, 65, 66, 67, 68, 85 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	1400	–	1427	-32	27	15, 41
	Frequency range	1475	–	1488	-50	1	42
	Frequency range	1488	–	1518	-50	1	15
85	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 26, 27, 30, 41, 53, 70, 71, 74	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 48, 51, 66	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 85 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	15
87	E-UTRA Band 1, 3, 7, 8, 22, 28, 31, 32, 33, 34, 38, 40, 42, 43, 47, 52, 65, 68, 72	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band, 20	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1	15
	Frequency range	470	–	694	-42	8
88	E-UTRA Band 1, 3, 7, 8, 20, 22, 28, 31, 32, 33, 34, 38, 40, 42, 43, 47, 52, 65, 68, 72	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 87	F_{DL_low}	–	F_{DL_high}	-20	1	15
	E-UTRA Band 88	F_{DL_low}	–	F_{DL_high}	-50	1	15
	Frequency range	470	–	694	-42	8
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2: As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th [or 5^th] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3: N/A NOTE 4: N/A NOTE 5: For non-synchronised TDD operation to meet these requirements some restriction will be needed for either the operating band or protected band NOTE 6: N/A NOTE 7:Applicable when co-existence with PHS system operating in 1884.5 -1919.6MHz. NOTE 8:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. NOTE 9:N/A NOTE 10:N/A NOTE 11:Whether the applicable frequency range should be 793-805MHz instead of 799-805MHz is TBD NOTE 12:The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB NOTE 13:N/A NOTE 14: N/A NOTE 15:These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the channel bandwidth. NOTE 16: N/A NOTE 17: N/A NOTE 18: N/A NOTE 19:Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. NOTE 20:N/A NOTE21:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE22:This requirement is applicable for power class 3 UE for any channel bandwidths within the range 2570 – 2615 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2605.5 – 2607.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2597 – 2605 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. For power class 2 UE for any channel bandwidths within the range 2570 – 2615 MHz, NS_44 shall apply. For power class 2 or 3 UE for carriers with channel bandwidth overlapping the frequency range 2615 – 2620 MHz the requirement applies with the maximum output power configured to +19 dBm in the IE P-Max. NOTE 23: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 24: As exceptions, measurements with a level up to the applicable requirement of -38 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 2^ndharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 2^nd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 25: As exceptions, measurements with a level up to the applicable requirement of -36 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 3^rdharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 3^rd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 26: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. NOTE 27: This requirement is applicable for any channel bandwidths within the range 1920 – 1980 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE 28: N/A NOTE 29: N/A NOTE 30: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz NOTE 31: N/A NOTE 32: Void NOTE 33: This requirement is only applicable for carriers with bandwidth confined within 1885-1920 MHz (requirement for carriers with at least 1RB confined within 1880 – 1885 MHz is not specified). This requirement applies for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1892.5 – 1894.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1895 – 1903 MHz. NOTE 34: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48. NOTE 35: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies. NOTE 36: This requirement is applicable for E-UTRA channel bandwidth allocated within 1920-1980 MHz. NOTE 37: Applicable when the upper edge of the channel bandwidth frequency is greater than 1980MHz. NOTE 38: Applicable when NS_33 or NS_34 is configured by the pre-configured radio parameters. NOTE 39: Applicable only when the assigned E-UTRA carrier is confined within 824 MHz and 849 MHz for UE category M1, M2 and UE category NB1 and NB2. NOTE 40: In the frequency range x-5950MHz, SE requirement of -30dBm/MHz should be applied; where x = max (5925, fc + 15), where fc is the channel centre frequency. NOTE 41: Applicable for all bandwidths, and when the lower edge of the assigned E-UTRA UL channel bandwidth frequency is greater than or equal to 1427 MHz + the channel BW assigned for 1.4, 3, 5 and 10 MHz bandwidth, and when the lower edge of the assigned E-UTRA UL channel bandwidth frequency is greater than or equal to 1440 MHz for 15 and 20 MHz bandwidth. This requirement shall be verified with UE transmission power of 15 dBm. NOTE 42: Applicable for 1.4 , 3 and 5 MHz bandwidth, and when the upper edge of the assigned E-UTRA UL channel bandwidth frequency is less than or equal to 1467 MHz assigned for10 MHz bandwidth, and when the upper edge of the assigned E-UTRA UL channel bandwidth frequency is less than or equal to 1463.8 MHz for 15 MHz bandwidth, and when the upper edge of the assigned E-UTRA UL channel bandwidth frequency is less than or equal to 1460.8 MHz for 20 MHz bandwidth. NOTE 43: The EIRP requirement is converted to conducted requirement depend on the supported post antenna connector gain G_{post connector} declared by the UE following the principle described in annex I. NOTE 44: For category NB1 and NB2 UE when carrier centre frequency is 1920.1 MHz, in case of single-tone uplink transmission the requirement is applicable only for sub-carrier index > 2. NOTE 45: Resolution BW is 10% of the measurement BW and the result should be integrated to achieve the measurement bandwidth. The sweep time shall be set at least as (sweep points)*(symbol length) to improve the measurement accuracy.

Table 6.6.3.2.3-1I: Spurious emission band UE co-existence limits Rel-17

E-UTRA Band	Spurious emission
E-UTRA Band	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
1	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 38, 40, 41, 42, 43, 44, 45, 50, 51, 52, 65, 67, 68, 69, 72, 73, 74, 75, 76, 87, 88 NR Band n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	15
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1880		1895	-40	1	15, 27
	Frequency range	1895		1915	-15.5	5	15, 26, 27
	Frequency range	1915		1920	+1.6	5	15, 26, 27, 44
2	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 27, 28, 29, 30, 41, 42, 48, 50, 51, 53, 66, 70, 71, 74, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25,	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43 NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
3	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 33, 34, 38, 39, 40, 41, 43, 44, 45, 50, 51, 65, 67, 68, 69, 72, 73,74, 75, 76, 87, 88 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 22, 42, 52 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3
4	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 41, 43, 48, 50, 51, 53, 66, 70, 71, 74, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
4	E-UTRA Band 42, NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
5	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 24, 25, 28, 29, 30, 31, 34, 38, 40, 42, 43, 45, 48, 50, 51, 65, 66, 70, 71, 73, 74, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 26	859	–	869	-27	1
	E-UTRA Band 41, 52, 53 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 18, 19	F_{DL_low}	–	F_{DL_high}	-40	1	39
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	39
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 39
6	E-UTRA Band 1, 9, 11, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	875	-37	1
	Frequency range	875	–	895	-50	1
	Frequency range	1884.5	–	1919.6	-41	0.3	7
	Frequency range	1884.5	–	1915.7	-41	0.3	8
7	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 20, 22, 26, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 50, 51, 52, 65, 66, 67, 68, 72, 74, 75, 76, 85, 87, 88, 103 NR Band n77,n78	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2570	–	2575	+1.6	5	15, 21, 26
	Frequency range	2575	–	2595	-15.5	5	15, 21, 26
	Frequency range	2595	–	2620	-40	1	15, 21
8	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40, 45, 50, 51, 65, 67, 68, 69, 72, 73, 74, 75, 76, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3, 7, 22, 41, 42, 43, 52 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	23
	Frequency range	860	–	890	-40	1	15, 23
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 23
9	E-UTRA Band 1, 3, 11, 18, 19, 21, 26, 28, 34	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
10	E-UTRA Band 2, 4, 5, 10, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 41, 43, 66, 70, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
10	E-UTRA Band 22, 42, NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
11	E-UTRA Band 1, 3, 11, 18, 19, 21, 28, 34, 40, 42, 65 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	945	–	960	-50	1

	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
12	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 26, 27, 30, 41, 53, 70, 71, 74, 103	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 48, 50, 51, 66 NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 85	F_{DL_low}	–	F_{DL_high}	-50	1	15
13	E-UTRA Band 2, 4, 5, 12, 13, 17, 25, 26, 27, 29, 41, 48, 50, 51, 53, 66, 70, 71, 74, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 14	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 24, 30, NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	769	–	775	-35	0.00625	15
	Frequency range	799	–	805	-35	0.00625	15
14	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 23, 24, 25, 26, 27, 29, 30, 41, 48, 53, 66, 70, 71, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	769	–	775	-35	0.00625	12, 15
	Frequency range	799	–	805	-35	0.00625	12, 15
17	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 26, 27, 30, 41, 70, 71, 74, 103	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 50, 51, 53, 66 NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 48, 85	F_{DL_low}	–	F_{DL_high}	-50	1	15
18	E-UTRA Band 1, 3, 11, 21, 34, 40, 42, 65 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	758	–	799	-50	1
	Frequency range	799	–	803	-40	1	15
	Frequency range	860	–	890	-40	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
19	E-UTRA Band 1, 3, 11, 21, 28, 34, 40, 42, 65 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
20	E-UTRA Band 1, 3, 7, 8, 22, 31, 32, 33, 34, 40, 43, 50, 51, 65, 67, 68, 72, 74, 75, 76, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 38, 42, 52, 69 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	758	–	788	-50	1
21	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 42, 65 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
22	E-UTRA Band 1, 3, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 39, 40, 43, 65, 67, 68, 69, 72, 75, 76, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	3510	–	3525	-40	1	15
	Frequency range	3525	–	3590	-50	1
23	E-UTRA Band 4, 5, 12, 13, 14, 17, 23, 24, 26, 27, 29, 30, 41, 66, 103	F_{DL_low}	–	F_{DL_high}	-50	1
24	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 48, 66, 70, 71, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
24	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
25	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 27, 28, 29, 30, 41, 42, 48, 53, 66, 70, 71, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 25	F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 43, NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
26	E-UTRA Band 1, 2, 3, 4, 5, 11, 12, 13, 14, 17, 18,19, 21, 24, 25, 26, 29, 30, 31, 34, 39, 40, 42, 43, 48, 50, 51, 65, 66, 70, 71, 73,74, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 41, 53 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	703	–	799	-50	1
	Frequency range	799	–	803	-40	1	15
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8
27	E-UTRA Band 1, 2, 3, 4, 5, 7, 12, 13, 14, 17, 25, 26, 27, 29, 30, 31, 38, 40, 41, 42, 43, 65, 66, 73, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 28	F_{DL_low}	–	790	-50	1
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	799	–	805	-35	0.00625
28	E-UTRA Band 1, 4, 22, 32, 42, 43, 50, 51, 65, 66, 73, 74, 75, 76 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}	–	F_{DL_high}	-50	1	19, 25
	E-UTRA Band 2, 3, 5, 7, 8, 18, 19, 20, 25, 26, 27, 31, 34, 38, 40, 41, 52, 72, 87, 88 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	19, 24
	Frequency range	470	–	694	-42	8	15, 35
	Frequency range	470	–	710	-26.2	6	34
	Frequency range	662	–	694	-26.2	6	15
	Frequency range	758	–	773	-32	1	15
	Frequency range	773	–	803	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	8, 19
30	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 24, 25, 26, 27, 29, 30, 38, 41, 48, 53, 66, 70, 71, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
30	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
31	E-UTRA Band 1, 5, 7, 8, 20, 22, 26, 27, 28, 31, 32, 33, 34, 38, 40, 42, 43, 50, 51, 52, 65, 67, 68, 69, 74, 75, 76, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	470	–	694	-42	8
…
33	E-UTRA Band 1, 7, 8, 20, 22, 28, 31, 32, 34, 38, 40, 42, 43, 52, 65, 67, 69, 72, 73, 75, 76, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1	5
33	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	15
34	E-UTRA Band 1, 3, 7, 8, 11, 18, 19, 20, 21, 22, 26, 28, 31, 32, 33, 38,39, 40, 41, 42, 43, 44, 45, 50, 51, 52, 65, 67, 69, 72, 73, 74, 75, 76, 87, 88 NR Band n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1	5
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2, 5
	Frequency range	1884.5	–	1915.7	-41	0.3	8
35
36
37			–
38	E-UTRA Band 1, 2, 3, 4, 5, 8, 12, 13, 14, 17, 20, 22, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 50, 51, 52, 65, 66, 67, 68, 72, 74, 75, 76, 85, 87, 88, 103 NR Band n77, n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	2620	–	2645	-15.5	5	15, 22, 26
	Frequency range	2645	–	2690	-40	1	15, 22
39	E-UTRA Band 1, 8, 22, 26, 28, 34, 40, 41, 42, 44, 45, 50, 51, 52, 73, 74 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1805		1855	-40	1	33
	Frequency range	1855		1880	-15.5	5	15,26,33
40	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 33, 34, 38, 39, 41, 42, 43, 44, 45, 50, 51, 52, 65, 67, 68, 69, 72, 73, 74, 75, 76, 87, 88 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	8
41	E-UTRA Band 1, 2, 3, 4, 5, 8, 12, 13 , 14, 17, 24, 25, 26, 27, 28, 29, 30, 34, 39, 40, 42, 44, 45, 48, 50, 51, 52, 65, 66, 70, 71, 73, 74, 85, 103 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	30
	NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		1915.7	-41	0.3	8, 30
42	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 11, 18, 19, 20, 21, 25, 26, 27, 28, 31, 32, 33, 34, 38, 40, 41, 44, 45, 50, 51, 65, 66, 67, 68, 69, 72, 73, 74, 75, 76, 87, 88 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
42	Frequency range	1884.5	–	1915.7	-41	0.3	8
43	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 20, 25, 26, 27, 28, 31,32, 33, 34, 38, 40, 50, 51, 65, 66, 67, 68, 69, 72, 73, 74, 75, 76, 85, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
44	E-UTRA Band 1, 40, 42, 45	F_{DL_low}	–	F_{DL_high}	-50	1	2
44	E-UTRA Band 3, 5, 8, 34, 39, 41, 73	F_{DL_low}	–	F_{DL_high}	-50	1
45	E-UTRA Band 1, 3, 5, 8, 34, 39, 40, 41, 42, 44, 52, 73	F_{DL_low}	–	F_{DL_high}	-50	1
…
47	E-UTRA Band 1, 3, 5, 7, 8, 22, 26, 28, 34, 39, 40, 41, 42, 44, 45, 65, 68, 72, 73 NR band n77, n78 , n79	FDL_low	–	FDL_high	-50	1
	Frequency range	5925	–	5950	-30 EIRP	1	38, 40, 43
	Frequency range	5815	–	5855	-30 EIRP	1	38, 43, 45
48	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 50, 51, 66, 70, 71, 74, 85, 103	FD_{L_low}	–	FD_{L_high}	-50	1
50	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 20, 26, 28, 29, 31, 34, 38, 39, 40, 41, 42, 43, 48, 52, 65, 66, 67, 68, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
51	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 20, 26, 28, 29, 31, 34, 38, 39, 40, 41, 42, 43, 48, 52, 65, 66, 67, 68, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
52	E-UTRA Band 1, 3, 5, 7, 8, 20, 28, 31, 33, 34, 38, 39, 40, 41, 45, 47, 50, 51, 68, 72, 73, 74, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
53	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 48, 66, 70, 71, 85, 103 NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1
65	E-UTRA Band 1, 3, 7, 8, 20, 22, 28, 31, 32, 38, 40, 42, 43, 50, 51, 65, 68, 69, 72, 74, 75, 76, 87, 88 NR Band n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 5, 11, 18, 19, 21, 26, 27, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	36
	Frequency range	1884.5	–	1915.7	-41	0.3	37
	Frequency range	1900	–	1915	-15.5	5	15, 26, 27
	Frequency range	1915	–	1920	+1.6	5	15, 26, 27
66	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 38, 41, 43, 50, 51, 53, 66, 70, 71, 74, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
66	E-UTRA Band 42, 48, NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
68	E-UTRA Band 3, 7, 8, 20, 28, 31, 38, 40, 47, 72, 74, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
68	E-UTRA Band 1, 22, 42, 43, 50, 51, 52, 65	F_{DL_low}	–	F_{DL_high}	-50	1	2
…
70	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 48, 53, 66, 70, 71, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
70	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
71	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 30, 48, 53, 66, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25, 41, 70, NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 29	F_{DL_low}	–	F_{DL_high}	-38	1	15
	E-UTRA Band 71	F_{DL_low}	–	F_{DL_high}	-50	1	15
72	E-UTRA Band 1, 7, 20, 22, 28, 31, 32, 33, 34, 38, 42, 43, 47, 52, 65, 68, 72, 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3, 8, 40	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	470	–	694	-42	8
73	E-UTRA Band 1, 26, 28, 33, 34, 39, 41, 42, 43, 44, 45, 47, 52	F_{DL_low}	–	F_{DL_high}	-50	1
73	E-UTRA Band 3, 5, 8, 27, 40	F_{DL_low}	–	F_{DL_high}	-50	1	2
74	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 18, 19, 20, 26, 28, 29, 31, 34, 38, 39, 40, 41, 42, 43, 48, 52, 65, 66, 67, 68, 85, 103 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
	NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	8
	Frequency range	1400	–	1427	-32	27	15, 41
	Frequency range	1475	–	1488	-50	1	42
	Frequency range	1488	–	1518	-50	1	15
85	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 26, 27, 30, 41, 53, 70, 71, 74, 103	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 48, 51, 66	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 85 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	15
87	E-UTRA Band 1, 3, 7, 8, 22, 28, 31, 32, 33, 34, 38, 40, 42, 43, 47, 52, 65, 68, 72	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band, 20	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 87, 88	F_{DL_low}	–	F_{DL_high}	-50	1	15
	Frequency range	470	–	694	-42	8
88	E-UTRA Band 1, 3, 7, 8, 20, 22, 28, 31, 32, 33, 34, 38, 40, 42, 43, 47, 52, 65, 68, 72	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 87	F_{DL_low}	–	F_{DL_high}	-20	1	15
	E-UTRA Band 88	F_{DL_low}	–	F_{DL_high}	-50	1	15
	Frequency range	470	–	694	-42	8
103	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 25, 26, 27, 29, 41, 48, 50, 51, 53, 66, 70, 71, 74, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 24, 30, NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	769	–	775	-35	0.00625
	Frequency range	799	–	805	-35	0.00625
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2: As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th [or 5^th] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3: N/A NOTE 4: N/A NOTE 5: For non-synchronised TDD operation to meet these requirements some restriction will be needed for either the operating band or protected band NOTE 6: N/A NOTE 7:Applicable when co-existence with PHS system operating in 1884.5 -1919.6MHz. NOTE 8:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. NOTE 9:N/A NOTE 10:N/A NOTE 11:Whether the applicable frequency range should be 793-805MHz instead of 799-805MHz is TBD NOTE 12:The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB NOTE 13:N/A NOTE 14: N/A NOTE 15:These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the channel bandwidth. NOTE 16: N/A NOTE 17: N/A NOTE 18: N/A NOTE 19:Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. NOTE 20:N/A NOTE21:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE22:This requirement is applicable for power class 3 UE for any channel bandwidths within the range 2570 – 2615 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2605.5 – 2607.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2597 – 2605 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. For power class 2 UE for any channel bandwidths within the range 2570 – 2615 MHz, NS_44 shall apply. For power class 2 or 3 UE for carriers with channel bandwidth overlapping the frequency range 2615 – 2620 MHz the requirement applies with the maximum output power configured to +19 dBm in the IE P-Max. NOTE 23: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 24: As exceptions, measurements with a level up to the applicable requirement of -38 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 2^ndharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 2^nd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 25: As exceptions, measurements with a level up to the applicable requirement of -36 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 3^rdharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 3^rd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 26: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. NOTE 27: This requirement is applicable for any channel bandwidths within the range 1920 – 1980 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE 28: N/A NOTE 29: N/A NOTE 30: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz NOTE 31: N/A NOTE 32: Void NOTE 33: This requirement is only applicable for carriers with bandwidth confined within 1885-1920 MHz (requirement for carriers with at least 1RB confined within 1880 – 1885 MHz is not specified). This requirement applies for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1892.5 – 1894.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1895 – 1903 MHz. NOTE 34: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48. NOTE 35: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies. NOTE 36: This requirement is applicable for E-UTRA channel bandwidth allocated within 1920-1980 MHz. NOTE 37: Applicable when the upper edge of the channel bandwidth frequency is greater than 1980MHz. NOTE 38: Applicable when NS_33 or NS_34 is configured by the pre-configured radio parameters. NOTE 39: Applicable only when the assigned E-UTRA carrier is confined within 824 MHz and 849 MHz for UE category M1, M2 and UE category NB1 and NB2. NOTE 40: In the frequency range x-5950MHz, SE requirement of -30dBm/MHz should be applied; where x = max (5925, fc + 15), where fc is the channel centre frequency. NOTE 41: Applicable for all bandwidths, and when the lower edge of the assigned E-UTRA UL channel bandwidth frequency is greater than or equal to 1427 MHz + the channel BW assigned for 1.4, 3, 5 and 10 MHz bandwidth, and when the lower edge of the assigned E-UTRA UL channel bandwidth frequency is greater than or equal to 1440 MHz for 15 and 20 MHz bandwidth. This requirement shall be verified with UE transmission power of 15 dBm. NOTE 42: Applicable for 1.4 , 3 and 5 MHz bandwidth, and when the upper edge of the assigned E-UTRA UL channel bandwidth frequency is less than or equal to 1467 MHz assigned for10 MHz bandwidth, and when the upper edge of the assigned E-UTRA UL channel bandwidth frequency is less than or equal to 1463.8 MHz for 15 MHz bandwidth, and when the upper edge of the assigned E-UTRA UL channel bandwidth frequency is less than or equal to 1460.8 MHz for 20 MHz bandwidth. NOTE 43: The EIRP requirement is converted to conducted requirement depend on the supported post antenna connector gain G_{post connector} declared by the UE following the principle described in annex I. NOTE 44: For category NB1 and NB2 UE when carrier centre frequency is 1920.1 MHz, in case of single-tone uplink transmission the requirement is applicable only for sub-carrier index > 2. NOTE 45: Resolution BW is 10% of the measurement BW and the result should be integrated to achieve the measurement bandwidth. The sweep time shall be set at least as (sweep points)*(symbol length) to improve the measurement accuracy.

6.6.3.2.4 Test description

6.6.3.2.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and channel bandwidths based on E-UTRA bands specified in Table 5.4.2.1-1. All of these configurations shall be tested with applicable test parameters for each channel bandwidth, and are shown in Table 6.6.3.2.4.1-1. The details of the uplink reference measurement channels (RMCs) are specified in Annexe A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.2.4.1-1: Test Configuration Table

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1) (Note 6, Note 7)				Low range, Mid range, High range (Note 6, 13, 16)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				Lowest, 5MHz, Highest (Note 13, 16)
Test Parameters for Channel Bandwidths
	Downlink Configuration			Uplink Configuration
Ch BW	Mod’n	RB allocation		Mod’n	RB allocation
		FDD	TDD		FDD	TDD
1.4MHz	N/A for Spurious Emissions testing			QPSK	6	6
1.4MHz				QPSK	1	1
3MHz				QPSK	15	15
3MHz				QPSK	1	1
5MHz				QPSK	25	25¹²
5MHz				QPSK	1	1¹²
5MHz				QPSK	20⁸	–
10MHz				QPSK	50	50
10MHz				QPSK	1	1
10MHz				QPSK	30¹⁵
10MHz				QPSK	32⁹	–
10MHz				QPSK	1^{10, 14}	–
15MHz				QPSK	75	75
15MHz				QPSK	54^{3, 11}	54^{4, 18}
15MHz				QPSK	1	1⁵
20MHz				QPSK	100	100
20MHz				QPSK	54^{3, 11}	54^{4, 18}
20MHz				QPSK	1	1⁵
Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, which applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 3: To be used for requirements under note 15 in table 6.6.3.2.3-1 and table 6.6.3.2.3-1A, note 16 in table 6.6.3.2.3-1B, note 21 in table 6.6.3.2.3-1C in high range at RB#(full allocation – 54), instead of full allocation. Note 4: To be used for requirements under note 16 in table 6.6.3.2.3-1 and table 6.6.3.2.3-1A, note 17 in table 6.6.3.2.3-1B, note 22 in table 6.6.3.2.3-1C in high range ‑ 5MHz at RB#(full allocation – 54), instead of full allocation. Note 5: For requirements under note 16 in table 6.6.3.2.-1 and table 6.6.3.2.3-1A, note 17 in table 6.6.3.2.3-1B, note 22 in table 6.6.3.2.3-1C (high range – 5MHz) is tested instead of high channel. Note 6: Do not apply for requirements under Note 13 in Tables 6.6.3.2.3-1 to 6.6.3.2.3-1C. Test frequencies for these requirements are defined in Table 6.6.3.2.4.1-2. Note 7: Void Note 8: For requirements under note 17 in table 6.6.3.2.3-1A, note 18 in table 6.6.3.2.3-1B, note 23 in table 6.6.3.2.3-1C (high range – 10MHz) is tested with RB #0 to RB #19 used. Note 9: For requirements under note 17 in table 6.6.3.2.3-1A, note 18 in table 6.6.3.2.3-1B, note 23 in table 6.6.3.2.3-1C high range is tested with RB #4 to RB #35 used. Note 10: For requirements under note 17 in table 6.6.3.2.3-1A, note 18 in table 6.6.3.2.3-1B, note 23 in table 6.6.3.2.3-1C high range is tested with RB #4 and (RB#max -4) used. Note 11: To be used for requirements under note 17 in table 6.6.3.2.3-1, note 18 in table 6.6.3.2.3-1A, note 19 in table 6.6.3.2.3-1B and note 27 in table 6.6.3.2.3-1C in low range at RB#0, instead of full allocation. Note 12: For requirements under note 16 in table 6.6.3.2.3-1 and table 6.6.3.2.3-1A, note 17 in table 6.6.3.2.3-1B, note 22 in table 6.6.3.2.3-1C, the message exception in Table 6.6.3.2.4.3-1 is used to test with the high range. Note 13: For requirements under note 31 in table 6.6.3.2.3-1C and note 34 in table 6.6.3.2.3-1D only 720.5 MHz is tested with 5 MHz and only 723 MHz is tested with 10 MHz. Note 14: For requirements under note 31 in table 6.6.3.2.3-1C and note 34 in table 6.6.3.2.3-1D RB #2 and RB #47 used. Note 15: To be used for requirements under note 31 in table 6.6.3.2.3-1C and note 34 in table 6.6.3.2.3-1D at RB#2, instead of full allocation. Note 16: For requirements under note 32 in table 6.6.3.2.3-1C and note 35 in table 6.6.3.2.3-1D only low range and 728 MHz with 10 MHz is tested. Note 17: Void. Note 18: To be used for requirements under note 33 in table 6.6.3.2.3-1D, table 6.6.3.2.3-1E or table 6.6.3.2.3-1F (high range-18 MHz for 15MHz channel bandwidth and high range-7 MHz for 20MHz channel bandwidth), instead of full allocation and high range. RB allocation shall start at RBstart=0.

Table 6.6.3.2.4.1-2: Test frequencies for E-UTRA channel bandwidth for operating band 3
with Note 13 (in Tables 6.6.3.2.3-1 to 6.6.3.2.3-1G)

Bandwidth [MHz]	N_UL	Frequency of Uplink [MHz]	N_DL	Frequency of Downlink [MHz]
1.4	19942	1784.2	1942	1879.2
3	19934	1783.4	1934	1878.4
5	19924	1782.4	1924	1877.4
10	19899	1779.9	1899	1874.9
15	19874	1777.4	1874	1872.4
20	19849	1774.9	1849	1869.9
Note: 1.4 and 3 MHz only tested for Rel8 and Rel9.

1. Connect the SS to the UE to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure A.7.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals are initially set up according to Annex C0, C.1 and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Table 6.6.3.2.4.1-1.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.2.4.3.

6.6.3.2.4.2 Test procedure

1. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 6.6.3.2.4.1-1. Since the UE has no payload data to send, the UE transmits uplink MAC padding bits on the UL RMC.

2. Send continuously uplink power control "up" commands in the uplink scheduling information to the UE until the UE transmits at P_UMAX level.

3. Measure the power of the transmitted signal with a measurement filter of bandwidths according to table 6.6.3.2.3-1 to 6.6.3.2.3-1G. For band 14 measurements made in a bandwidth of 6.25kHz, measurement parameter settings defined in table 6.6.3.2.4.2-1 shall be used. The centre frequency of the filter shall be stepped in contiguous steps according to table 6.6.3.2.5-1. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

Table 6.6.3.2.4.2-1: Measurement setup for band 14

	Option 1: Measurement with No RMS VBW available	Option2 Measurement with VBW Filtering on Power scale
VBW	>=62.5 kHz (10 times or more the RBW)	<=43Hz
RBW	<=6.25kHz	<=6.25kHz
Detector type	Averages signal envelope during each measurement point, such as "RMS detector"	Peak
Averaging mode (Trace averaging)	Power (RMS voltage)	Power (RMS voltage), as controlled by "Average Type"
Average Type (applies to detector)	Power (RMS voltage) (automatically occurs with "RMS detector")	Not applicable
Average Type (applies to VBW filter)	Not applicable	Power (RMS voltage)
Number of averages	30, to reduce variance as required, or use an even longer sweep time	1 or use an even narrower VBW filter, thus a longer sweep time
Sweep time	[Don’t specify]	Sweep rate (span divided by sweep time) <= 0.8 * RBW*VBW

6.6.3.2.4.3 Message contents

Message contents are according to TS 36.508 [7] subclause 4.6 with the following exceptions:

Table 6.6.3.2.4.3-1: SystemInformationBlockType1
for Note 16 in table 6.6.3.2.3-1 and table 6.6.3.2.3-1A,
Note 17 in table 6.6.3.2.3-1B, Note 22 in table 6.6.3.2.3-1C, table 6.6.3.2.3-1D, table 6.6.3.2.3-1E, table 6.6.3.2.3-1F and table 6.6.3.2.3-1G

Derivation Path: TS 36.508 [7] clause 4.4.3.2, Table 4.4.3.2-3 SystemInformationBlockType1
Information Element	Value/remark	Comment	Condition
p-Max	19

6.6.3.2.5 Test requirement

Test requirements for Spurious Emissions UE Co-existence are the same as the minimum requirements and are not repeated in this section.

The measured average power of spurious emission, derived in step 3, shall not exceed the described value in tables 6.6.3.2.3-1 to 6.6.3.2.3-1G according to the following rule:

The requirements for the UE are release specific and can be found in Tables 6.6.3.2.3-1 to 6.6.3.2.3-1G. If the UE support a band, which is not defined in the table corresponding UE’s release, the requirements for this band are taken from the table of earliest release where requirements for this band are defined. This has been described in following Table 6.6.3.2.5-1.

Table 6.6.3.2.5-1: UE Requirements according to UE E-UTRA release and supported E-UTRA band

Band	UE Requirements per release
Band	Rel-8	Rel-9	Rel-10	Rel-11	Rel-12	Rel-13		Rel-14	Rel-15	Rel-16	Rel-17
1	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
2	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
3	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
4	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
5	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
6	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
7	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
8	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
9	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
10	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
11	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
12	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
13	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
14	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
…
17	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
18	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
19	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
20	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
21	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
22	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
23	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
24	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
25	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
26	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
27	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
28	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
30	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
31	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
…
33	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
34	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
35
36
37
38	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
39	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
40	Table 6.6.3.2.3-1	Table 6.6.3.2.3-1A	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
41	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
42	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
43	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1B	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
44	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1C	Table 6.6.3.2.3-1D	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
45	Table 6.6.3.2.3-1E	Table 6.6.3.2.3-1E	Table 6.6.3.2.3-1E	Table 6.6.3.2.3-1E	Table 6.6.3.2.3-1E	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
…
48	Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1F		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
…..
53	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1H		Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
…											Table 6.6.3.2.3-1I
65	N/A ¹	Table 6.6.3.2.3-1E	Table 6.6.3.2.3-1E	Table 6.6.3.2.3-1E	Table 6.6.3.2.3-1E	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
66	N/A ²	N/A ²	Table 6.6.3.2.3-1E	Table 6.6.3.2.3-1E	Table 6.6.3.2.3-1E	Table 6.6.3.2.3-1E		Table 6.6.3.2.3-1F	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
…
68	N/A ¹	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G		Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
…
71	N/A ¹	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G		Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
72	N/A ¹	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G		Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
…..
74	N/A ¹	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G		Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
87	N/A ¹	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G		Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
88	N/A ¹	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G		Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1H	Table 6.6.3.2.3-1I
72	N/A ¹	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G		Table 6.6.3.2.3-1G		Table 6.6.3.2.3-1I
74	N/A ¹	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G		Table 6.6.3.2.3-1G		Table 6.6.3.2.3-1I
85	N/A ¹	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G	Table 6.6.3.2.3-1G		Table 6.6.3.2.3-1G		Table 6.6.3.2.3-1I
Note 1: Operating band with number > 64 requires Rel-9 signalling (refer to TS 36.307 Ch. 3A.1 [16]) and tests can only be done from Rel-9 and onwards. Note 2: Asymmetric operating band is release independent from release 10 (refer to TS 36.307 Ch. 3A.1 [16]) and tests can only be done from Rel-10 and onwards. Note 3: Protected bands with Note 38 in Table 6.6.3.2.3-1E are tested in 6.6.3EA.2 or 6.6.3F.2.

NOTE 1: The frequency range applicable with network signalled values of NS_05, NS_08, NS_09, NS_15,NS_16, NS_27, NS_36, NS_45 are covered in 6.6.3.3 Additional Spurious Emissions.

NOTE 2: The following is applied to Note2 in Table 6.6.3.2.3-1, Table 6.6.3.2.3-1A, Table 6.6.3.2.3-1B, Table 6.6.3.2.3-1C and Table 6.6.3.2.3-1E. For frequency with 2nd, 3rd or 4th harmonic spurious emissions, the measurements are covered in 6.6.3.1.

NOTE 2: The restriction on the maximum uplink transmission to 54 RB in Notes 14 and 15 of Table 6.6.3.2.5-1 is intended for conformance testing and may be applied to network operation to facilitate coexistence when the aggressor and victim bands are deployed in the same geographical area. The applicable spurious emission requirement of -15.5 dBm/5MHz is a least restrictive technical condition for FDD/TDD coexistence and may have to be revised in the future.

6.6.3.2_1 Void

6.6.3.2A Spurious emission band UE co-existence for CA

Editor’s note:

– This test case contains different requirements for different UE releases

– Additional TP analysis needs to be added to TR36.905

6.6.3.2A.0 Minimum conformance requirements

This clause specifies the requirements for the specified carrier aggregation configurations for coexistence with protected bands.

For inter-band carrier aggregation with the uplink assigned to two E-UTRA bands, the requirements in Table 6.6.3.2A.0-1a to 6.6.3.2A.0-1f apply on each component carrier with both component carriers are active.

NOTE 2: For inter-band carrier aggregation with uplink assigned to two E-UTRA bands the requirements in Table 6.6.3.2A.0-1a to 6.6.3.2A.0-1f could be verified by measuring spurious emissions at the specific frequencies where second and third order intermodulation products generated by the two transmitted carriers can occur; in that case, the requirements for remaining applicable frequencies in Table 6.6.3.2A.0-1a to 6.6.3.2A.0-1f would be considered to be verified by the measurements verifying the one uplink inter-band CA UE to UE co-existence requirements.

Table 6.6.3.2A.0-1a: Requirements for dual-uplink inter-band carrier aggregation limits for Rel-11 and Rel-12

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Note
CA_1A-3A	E-UTRA Band 1, 5, 7, 8, 20, 26, 27, 28, 31, 32, 38, 40, 41, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3, 34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 11,18,19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	7, 10
	Frequency range	1880		1895	-40	1	3,12
	Frequency range	1895		1915	-15.5	5	3, 12, 13
	Frequency range	1915		1920	+1.6	5	3, 12, 13
CA_1A-5A	E-UTRA Band 1, 5, 7, 8, 22, 28, 31, 38, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3,34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 26	859	–	869	-27	1
	E-UTRA band 41	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_1A-7A	E-UTRA Band 1, 5, 7, 8, 20, 22, 26, 27, 28, 31, 32, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3, 34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	Frequency range	1880		1895	-40	1	3,12
	Frequency range	1895		1915	-15.5	5	3, 12, 13
	Frequency range	1915		1920	+1.6	5	3, 12, 13
	Frequency range	2570	–	2575	+1.6	5	3, 13, 14
	Frequency range	2575	–	2595	-15.5	5	3, 13, 14
	Frequency range	2595	–	2620	-40	1	3, 14
CA_1A-8A	E-UTRA Band 1, 20, 26, 28, 31, 32, 38, 40	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2,3
	E-UTRA band 7, 22, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8, 34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	11
	Frequency range	860	–	890	-40	1	3, 11
	Frequency range	1884.5	–	1915.7	-41	0.3	7, 11
	Frequency range	1880		1895	-40	1	3,12
	Frequency range	1895		1915	-15.5	5	3, 12, 13
	Frequency range	1915		1920	+1.6	5	3, 12, 13
CA_1A-19A	E-UTRA Band 1, 3, 11, 21, 28, 40, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	Frequency range	860	–	890	-40	1	3, 8
	Frequency range	945	–	960	-50	1	3
	Frequency range	1884.5	–	1915.7	-41	0.3	3, 7
	Frequency range	1839.9	–	1879.9	-50	1	3
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
CA_1A-21A	E-UTRA Band 11	F_{DL_low}	–	F_{DL_high}	-35	1	3, 16
	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 21	F_{DL_low}	–	F_{DL_high}	-50	1	16
	Frequency range	1884.5	–	1915.7	-41	0.3	7
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
CA_2A-4A	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 22, 23, 24, 26, 27, 28, 29, 30, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-13A	E-UTRA Band 4, 5,10,12,13,17, 22, 23, 26, 27, 29, 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2,14, 25	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 24, 30, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	769	–	775	-35	0.00625	3
	Frequency range	799	–	805	-35	0.00625	3, 9
CA_3A-5A	E-UTRA Band 1, 5, 7, 8, 22, 28, 31, 38, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3,34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 26	859	–	869	-27	1
CA_3A-7A	E-UTRA Band 1, 5, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 40, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	2570	–	2575	+1.6	5	3, 13, 14
	Frequency range	2575	–	2595	-15.5	5	3, 13, 14
	Frequency range	2595	–	2620	-40	1	3, 14
CA_3A-8A	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3, 8	F_{DL_low}	–	F_{DL_high}	-50	1	2, 3
	E-UTRA band 11, , , 21	F_{DL_low}	–	F_{DL_high}	-50	1	10,11
	E-UTRA band 7, 22, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	4, 10, 11
	Frequency range	860	–	890	-40	1	3,11,17
CA_3A-19A	E-UTRA Band 1, 11, 21, 28, 40	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	860	–	890	-40	1	3, 8
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	3, 4
	Frequency range	1839.9	–	1879.9	-50	1	3
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
CA_3A-20A	E-UTRA Band 1, 7, 8, 31, 32, 33, 34, 40, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3, 20	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	758	–	788	-50	1
eCA_3A-26A	E-UTRA Band 1, 5, 7, 26, 34, 39, 40, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA band 22, 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	4, 10
	Frequency range	703	–	799	-50	1
	Frequency range	799	–	803	-40	1	3
	Frequency range	851	–	859	-53	0.00625	15
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
CA_4A-7A	E-UTRA Band 2, 4, 5, 7, 10, 12, 13, 14, 17, 26, 27, 28, 29, 30, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	2570	–	2575	+1.6	5	3, 13, 14
	Frequency range	2575	–	2595	-15.5	5	3, 13, 14
	Frequency range	2595	–	2620	-40	1	3, 14
CA_4A-12A	E-UTRA Band 2, 5, 7,13, 14, 17, 22, 23, 24, 25, 26, 27, 30, 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	3
CA_4A-13A	E-UTRA Band 2,4, 5, 7, 10,12,13,17, 22, 23,25, 26, 27, 29, 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 14	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 24, 30, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	769	–	775	-35	0.00625	3
	Frequency range	799	–	805	-35	0.00625	3, 9
CA_4A-17A	E-UTRA Band 2, 5, 7,13, 14, 17, 22, 23, 24, 25, 26, 27, 30, 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	3
CA_5A-7A	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 12, 13, 14, 17, 22, 28, 29, 30, 31, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 26	859	–	869	-27	1
	Frequency range	2570	–	2575	+1.6	5	3, 13, 14
	Frequency range	2575	–	2595	-15.5	5	3, 13, 14
	Frequency range	2595	–	2620	-40	1	3, 14
CA_5A-12A	E-UTRA Band 2, 5, 13, 14, 17, 22, 23, 24, 25, 30, 31, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 4, 10, 41	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859	–	869	-27	1
	E-UTRA band 12	F_{DL_low}	–	F_{DL_high}	-50	1	3
CA_5A-17A	E-UTRA Band 2, 5, 13, 14, 17, 22, 23, 24, 25, 30, 31, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 4, 10, 41	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859	–	869	-27	1
	E-UTRA band 12	F_{DL_low}	–	F_{DL_high}	-50	1	3
CA_7A-20A	E-UTRA Band 1,3, 7, 8, 22, 28, 31,32, 33, 34, 40, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	2570	–	2575	+1.6	5	3, 13, 14
	Frequency range	2575	–	2595	-15.5	5	3, 13, 14
	Frequency range	2595	–	2620	-40	1	3, 14
CA_7A-28A	E-UTRA Band 2, 3, 5, 7,8, 20, 26, 27,31,34, 40	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 1, 4, 10, 22, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}	–	F_{DL_high}	-50	1	5, 6
	Frequency range	758	–	773	-32	1	3
	Frequency range	773	–	803	-50	1
	Frequency range	2570	–	2575	+1.6	5	3, 13, 14
	Frequency range	2575	–	2595	-15.5	5	3, 13, 14
	Frequency range	2595	–	2620	-40	1	3, 14
CA_19A-21A	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 11	F_{DL_low}	–	F_{DL_high}	-50	1	3, 16
	E-UTRA Band 21	F_{DL_low}	–	F_{DL_high}	-50	1	16
	Frequency range	860	–	890	-40	1	3, 8
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	4
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
CA 39A-41A	E-UTRA Band 1, 8, 26, 34, 40, 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1805	–	1855	-40	1	20
	Frequency range	1855	–	1880	-15.5	5	3, 13, 20
	Frequency range	1884.5	–	1915.7	-41	0.3	4, 18
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.2-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1.3-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.4.2-1) for which the 2^nd, 3^rd or 4^th harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 3: These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.0-1 from the edge of the aggregated channel bandwidth. NOTE 4:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. NOTE 5:Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. NOTE 6: As exceptions, measurements with a level up to the applicable requirement of -36 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 3^rdharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 3^rd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 7: Applicable when NS_05 in section 6.6.3.3.3.2 is signalled by the network. NOTE 8: Applicable when NS_08 in subclause 6.6.3.3.3.4 is signalled by the network NOTE 9: Whether the applicable frequency range should be 793-805MHz instead of 799-805MHz is TBD. NOTE10: This requirement applies for 5, 10, 15 and 20 MHz E-UTRA channel bandwidth allocated within 1744.9MHz and 1784.9MHz. NOTE 11: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 12: This requirement is applicable for any channel bandwidths within the range 1920 – 1980 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE13: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. NOTE14:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE 15:Applicable when NS_15 in subclause 6.6.3.3.3.10 is signalled by the network. NOTE 16:Applicable when NS_09 in subclause 6.6.3.3.3.5 is signalled by the network NOTE 17: This requirement is applicable only when Band 3 transmission frequency is less than or equal to 1765 MHz. NOTE 18: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz NOTE 19: Void. NOTE 20: This requirement is only applicable for carriers with bandwidth confined within 1885-1920 MHz (requirement for carriers with at least 1RB confined within 1880 – 1885 MHz is not specified). This requirement applies for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1892.5 – 1894.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1895 – 1903 MHz.

Table 6.6.3.2A.0-1b: Requirements for dual-uplink inter-band carrier aggregation limits for Rel-13

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
CA_1A-3A	E-UTRA Band 1, 5, 7, 8, 20, 26, 27, 28, 31, 32, 38, 40, 41, 43, 44, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3, 34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 11,18,19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	7, 10
	Frequency range	1880		1895	-40	1	3,12
	Frequency range	1895		1915	-15.5	5	3, 12, 13
	Frequency range	1915		1920	+1.6	5	3, 12, 13
CA_1A-5A	E-UTRA Band 1, 5, 7, 8, 22, 28, 31, 38, 40, 42, 43, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3,34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 26	859	–	869	-27	1
	E-UTRA band 41	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_1A-7A	E-UTRA Band 1, 5, 7, 8, 20, 22, 26, 27, 28, 31,32, 40, 42, 43, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3, 34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	Frequency range	1880		1895	-40	1	3,12
	Frequency range	1895		1915	-15.5	5	3, 12, 13
	Frequency range	1915		1920	+1.6	5	3, 12, 13
	Frequency range	2570	–	2575	+1.6	5	3, 13, 14
	Frequency range	2575	–	2595	-15.5	5	3, 13, 14
	Frequency range	2595	–	2620	-40	1	3, 14
CA_1A-8A	E-UTRA Band 1, 20, 26, 28, 31, 32, 38, 40, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2,3
	E-UTRA band 7, 22, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8, 34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	11
	Frequency range	860	–	890	-40	1	3, 11
	Frequency range	1884.5	–	1915.7	-41	0.3	7, 11
	Frequency range	1880		1895	-40	1	3,12
	Frequency range	1895		1915	-15.5	5	3, 12, 13
	Frequency range	1915		1920	+1.6	5	3, 12, 13
CA_1A-18A	E-UTRA Band 1, 3, 11, 21, 40, 42, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	Frequency range	758	–	799	-50	1
	Frequency range	799	–	803	-40	1	3
	Frequency range	860	–	890	-40	1
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	3, 7
	Frequency range	1839.9	–	1879.9	-50	1	3
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
CA_1A-19A	E-UTRA Band 1, 3, 11, 21, 28, 40, 42, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	Frequency range	860	–	890	-40	1	3, 8
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	3, 7
	Frequency range	1839.9	–	1879.9	-50	1	3
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
CA_1A-21A	E-UTRA Band 11	F_{DL_low}	–	F_{DL_high}	-35	1	3, 16
	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 42, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 21	F_{DL_low}	–	F_{DL_high}	-50	1	16
	Frequency range	1884.5	–	1915.7	-41	0.3	7
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
CA_1A-26A	E-UTRA Band 1,5, 7, 11, 18, 19, 20, 21, 22, 26, 27, 31, 38, 40, 42, 43, 44, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1880	–	1895	-40	1	3, 12
	Frequency range	1895	–	1915	-15.5	5	3, 12, 13
	Frequency range	1915	–	1920	+1.6	5	3, 12, 13
	Frequency range	1884.5	–	1915.7	-41	0.3	7
	Frequency range	945	–	960	-50	1
	E-UTRA Band 41	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 3, 34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	Frequency range	703	–	799	-50	1
	Frequency range	799	–	803	-40	1	3
	Frequency range	1839.9	–	1879.9	-50	1	3
CA_1A-28A	E-UTRA Band 5, 7, 8, 18, 19, 20, 26, 27, 31, 32, 38, 40, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 22, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 3, 34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	5, 21
	E-UTRA Band 1, 65	F_{DL_low}	–	F_{DL_high}	-50	1	5, 6
	Frequency range	470	–	694	-42	8	3, 22
	Frequency range	470	–	710	-26.2	6	23
	Frequency range	758	–	773	-32	1	3
	Frequency range	773	–	803	-50	1
	Frequency range	662	–	694	-26.2	6	3
	Frequency range	1880		1895	-40	1	3,12
	Frequency range	1895		1915	-15.5	5	3, 12, 13
	Frequency range	1915		1920	+1.6	5	3, 12, 13
	Frequency range	1839.9	–	1879.9	-50	1	3
	Frequency range	1884.5	–	1915.7	-41	0.3	5, 7
CA_1A-42A	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 38, 40, 41, 44, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3, 34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	Frequency range	1880		1895	-40	1	3,12
	Frequency range	1895		1915	-15.5	5	3, 12, 13
	Frequency range	1915		1920	+1.6	5	3, 12, 13
	Frequency range	1839.9	–	1879.9	-50	1	3
	Frequency range	1884.5	–	1915.7	-41	0.3	3, 7
CA_2A-4A	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 22, 23, 24, 26, 27, 28, 29, 30, 41, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-5A	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 23, 24, 28, 29, 30, 42	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 26	859	–	869	-27	1
	E-UTRA Band 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-12A	E-UTRA Band 5, 13, 14, 17, 23, 24, 26, 27, 30, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 12, 25	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 4, 10	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-13A	E-UTRA Band 4, 5,10,12,13,17, 22, 23, 26, 27, 29, 41, 42, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2,14, 25	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 24, 30, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	769	–	775	-35	0.00625	3
	Frequency range	799	–	805	-35	0.00625	3, 9
CA_3A-5A	E-UTRA Band 1, 5, 7, 8, 22, 28, 31, 38, 40, 42, 43, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3,34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 26	859	–	869	-27	1
CA_3A-7A	E-UTRA Band 1, 5, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 40, 43, 44, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	2570	–	2575	+1.6	5	3, 13, 14
	Frequency range	2575	–	2595	-15.5	5	3, 13, 14
	Frequency range	2595	–	2620	-40	1	3, 14
CA_3A-8A	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40, 44, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3, 8	F_{DL_low}	–	F_{DL_high}	-50	1	2, 3
	E-UTRA band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	10,11
	E-UTRA band 7, 22, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	4, 10, 11
	Frequency range	860	–	890	-40	1	3,11,17
CA_3A-19A	E-UTRA Band 1, 11, 21, 28, 40, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	860	–	890	-40	1	3, 8
	Frequency range	945	–	960	-50	1	3
	Frequency range	1884.5	–	1915.7	-41	0.3	3, 4, 7
	Frequency range	1839.9	–	1879.9	-50	1	3
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
CA_3A-20A	E-UTRA Band 1, 7, 8, 31, 32, 33, 34, 40, 43, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3, 20	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	758	–	788	-50	1
CA_3A-26A	E-UTRA Band 1, 5, 7, 26, 34, 39, 40, 43, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA band 22, 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	1884.5	–	1915.7	-41	0.3	4, 10
	Frequency range	703	–	799	-50	1
	Frequency range	799	–	803	-40	1	3
	Frequency range	851	–	859	-53	0.00625	15
	Frequency range	945	–	960	-50	1
	Frequency range	1839.9	–	1879.9	-50	1
CA_4A-5A	E-UTRA Band 2, 4, 5, 7, 10, 12, 13, 14, 17, 23, 24, 25, 28, 29, 30, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 26	859	–	869	-27	1
	E-UTRA band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_4A-7A	E-UTRA Band 2, 4, 5, 7, 10, 12, 13, 14, 17, 26, 27, 28, 29, 30, 43, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	2570	–	2575	+1.6	5	3, 13, 14
	Frequency range	2575	–	2595	-15.5	5	3, 13, 14
	Frequency range	2595	–	2620	-40	1	3, 14
CA_4A-12A	E-UTRA Band 2, 5, 7,13, 14, 17, 22, 23, 24, 25, 26, 27, 30, 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10, 42, 66	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	3
CA_4A-13A	E-UTRA Band 2,4, 5, 7, 10,12,13,17, 22, 23,25, 26, 27, 29, 41, 43, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 14	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 24, 30, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	769	–	775	-35	0.00625	3
	Frequency range	799	–	805	-35	0.00625	3, 9
CA_4A-17A	E-UTRA Band 2, 5, 7,13, 14, 17, 22, 23, 24, 25, 26, 27, 30, 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10, 42, 66	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12	F_{DL_low}	–	F_{DL_high}	-50	1	3
CA_5A-7A	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 12, 13, 14, 17, 22, 28, 29, 30, 31, 40, 42, 43, 65, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 26	859	–	869	-27	1
	Frequency range	2570	–	2575	+1.6	5	3, 13, 14
	Frequency range	2575	–	2595	-15.5	5	3, 13, 14
	Frequency range	2595	–	2620	-40	1	3, 14
CA_5A-12A	E-UTRA Band 2, 5, 13, 14, 17, 22, 23, 24, 25, 30, 31, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 4, 10, 41, 66	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859	–	869	-27	1
	E-UTRA band 12	F_{DL_low}	–	F_{DL_high}	-50	1	3
CA_5A-17A	E-UTRA Band 2, 5, 13, 14, 17, 22, 23, 24, 25, 30, 31, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 4, 10, 41, 66	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859	–	869	-27	1
	E-UTRA band 12	F_{DL_low}	–	F_{DL_high}	-50	1	3
CA_7A-20A	E-UTRA Band 1,3, 7, 8, 22, 28, 31, 32, 33, 34, 40, 43, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	2570	–	2575	+1.6	5	3, 13, 14
	Frequency range	2575	–	2595	-15.5	5	3, 13, 14
	Frequency range	2595	–	2620	-40	1	3, 14
CA_7A-28A	E-UTRA Band 2, 3, 5, 7, 8, 20, 26, 27, 31, 34, 40	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 1, 4, 10, 22, 42, 43, 65, 66	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}	–	F_{DL_high}	-50	1	5, 6
	Frequency range	758	–	773	-32	1	3
	Frequency range	773	–	803	-50	1
	Frequency range	2570	–	2575	+1.6	5	3, 13, 14
	Frequency range	2575	–	2595	-15.5	5	3, 13, 14
	Frequency range	2595	–	2620	-40	1	3, 14
CA_18A-28A	E-UTRA Band 11, 21	F_{DL_low}	–	F_{DL_high}	-50	1	5, 21
	E-UTRA Band 1, 65	F_{DL_low}	–	F_{DL_high}	-50	1	5, 6
	E-UTRA Band 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 3, 34, 40	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	470	–	710	-26.2	6	23
	Frequency range	758	–	773	-32	1	3
	Frequency range	773	–	799	-50	1
	Frequency range	799	–	803	-40	1	3
	Frequency range	860	–	890	-40	1
	Frequency range	945	–	960	-50	1	3
	Frequency range	1884.5	–	1915.7	-41	0.3	4
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
CA_19A-21A	E-UTRA Band 1, 18, 19, 28, 34, 40,42, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 11	F_{DL_low}	–	F_{DL_high}	-50	1	3, 16
	E-UTRA Band 21	F_{DL_low}	–	F_{DL_high}	-50	1	16
	Frequency range	860	–	890	-40	1	3, 8
	Frequency range	945	–	960	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3	4
	Frequency range	1839.9	–	1879.9	-50	1
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
CA 39A-41A	E-UTRA Band 1, 8, 26, 34, 40, 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1805	–	1855	-40	1	20
	Frequency range	1855	–	1880	-15.5	5	3, 13, 20
CA 39A-41C	E-UTRA Band 1, 8, 26, 34, 40, 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1805	–	1855	-40	1	20
	Frequency range	1855	–	1880	-15.5	5	3, 13, 20
CA 39C-41A	E-UTRA Band 34, 40, 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. In case the exceptions are allowed due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3 or 4 for the 2^nd, 3^rd or 4^th harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3: These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the aggregated channel bandwidth. NOTE 4:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. NOTE 5:Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. NOTE 6: As exceptions, measurements with a level up to the applicable requirement of -36 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 3^rdharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 3^rd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 7: Applicable when NS_05 in section 6.6.3.3.3.2 is signalled by the network. NOTE 8: Applicable when NS_08 in subclause 6.6.3.3.3.4 is signalled by the network NOTE 9: Whether the applicable frequency range should be 793-805MHz instead of 799-805MHz is TBD. NOTE10: This requirement applies for 5, 10, 15 and 20 MHz E-UTRA channel bandwidth allocated within 1744.9MHz and 1784.9MHz. NOTE 11: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 12: This requirement is applicable for any channel bandwidths within the range 1920 – 1980 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE13: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. NOTE14:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE 15:Applicable when NS_15 in subclause 6.6.3.3.3.10 is signalled by the network. NOTE 16:Applicable when NS_09 in subclause 6.6.3.3.3.5 is signalled by the network NOTE 17: This requirement is applicable only when Band 3 transmission frequency is less than or equal to 1765 MHz. NOTE 18: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz NOTE 19: Void. NOTE 20: This requirement is only applicable for carriers with bandwidth confined within 1885-1920 MHz (requirement for carriers with at least 1RB confined within 1880 – 1885 MHz is not specified). This requirement applies for an uplink transmission bandwidth less than or equal to [54 RB] for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1892.5 – 1894.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1895 – 1903 MHz. NOTE 21: As exceptions, measurements with a level up to the applicable requirement of -38 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 2^ndharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 2^nd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 22: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies. NOTE 23: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48.

Table 6.6.3.2A.0-1c: Requirements for dual-uplink inter-band carrier aggregation limits for Rel-14

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band		Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
CA_1A-3A	E-UTRA Band 1, 5, 7, 8, 20, 26, 27, 28, 31, 32, 38, 40, 41, 43, 44, 65, 67		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3, 34		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 11,18,19, 21		F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA band 22, 42		F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range		1884.5	–	1915.7	-41	0.3	7, 10
	Frequency range		1880		1895	-40	1	3,12
	Frequency range		1895		1915	-15.5	5	3, 12, 13
	Frequency range		1915		1920	+1.6	5	3, 12, 13
CA_1A-5A	E-UTRA Band 1, 5, 7, 8, 22, 28, 31, 38, 40, 42, 43, 65		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3,34		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 26		859	–	869	-27	1
	E-UTRA band 41		F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_1A-7A	E-UTRA Band 1, 5, 7, 8, 20, 22, 26, 27, 28, 31,32, 40, 42, 43, 65, 67		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3, 34		F_{DL_low}	–	F_{DL_high}	-50	1	3
	Frequency range		1880		1895	-40	1	3,12
	Frequency range		1895		1915	-15.5	5	3, 12, 13
	Frequency range		1915		1920	+1.6	5	3, 12, 13
	Frequency range		2570	–	2575	+1.6	5	3, 13, 14
	Frequency range		2575	–	2595	-15.5	5	3, 13, 14
	Frequency range		2595	–	2620	-40	1	3, 14
CA_1A-8A	E-UTRA Band 1, 20, 26, 28, 31, 32, 38, 40, 65, 67		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3		F_{DL_low}	–	F_{DL_high}	-50	1	2,3
	E-UTRA band 7, 22, 41, 42, 43		F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8, 34		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 11, 21		F_{DL_low}	–	F_{DL_high}	-50	1	11
	Frequency range		860	–	890	-40	1	3, 11
	Frequency range		1884.5	–	1915.7	-41	0.3	7, 11
	Frequency range		1880		1895	-40	1	3,12
	Frequency range		1895		1915	-15.5	5	3, 12, 13
	Frequency range		1915		1920	+1.6	5	3, 12, 13
CA_1A-18A	E-UTRA Band 1, 3, 11, 21, 40, 42, 65		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34		F_{DL_low}	–	F_{DL_high}	-50	1	3
	Frequency range		758	–	799	-50	1
	Frequency range		799	–	803	-40	1	3
	Frequency range		860	–	890	-40	1
	Frequency range		945	–	960	-50	1
	Frequency range		1884.5	–	1915.7	-41	0.3	3, 7
	Frequency range		1839.9	–	1879.9	-50	1	3
	Frequency range		2545	–	2575	-50	1
	Frequency range		2595	–	2645	-50	1
CA_1A-19A	E-UTRA Band 1, 3, 11, 21, 28, 40, 42, 65		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34		F_{DL_low}	–	F_{DL_high}	-50	1	3
	Frequency range		860	–	890	-40	1	3, 8
	Frequency range		945	–	960	-50	1
	Frequency range		1884.5	–	1915.7	-41	0.3	3, 7
	Frequency range		1839.9	–	1879.9	-50	1	3
	Frequency range		2545	–	2575	-50	1
	Frequency range		2595	–	2645	-50	1
CA_1A-21A	E-UTRA Band 11		F_{DL_low}	–	F_{DL_high}	-35	1	3, 16
	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 42, 65		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 21		F_{DL_low}	–	F_{DL_high}	-50	1	16
	Frequency range		1884.5	–	1915.7	-41	0.3	7
	Frequency range		945	–	960	-50	1
	Frequency range		1839.9	–	1879.9	-50	1
	Frequency range		2545	–	2575	-50	1
	Frequency range		2595	–	2645	-50	1
CA_1A-26A	E-UTRA Band 1,5, 7, 11, 18, 19, 20, 21, 22, 26, 27, 31, 38, 40, 42, 43, 44, 65		F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range		1880	–	1895	-40	1	3, 12
	Frequency range		1895	–	1915	-15.5	5	3, 12, 13
	Frequency range		1915	–	1920	+1.6	5	3, 12, 13
	Frequency range		1884.5	–	1915.7	-41	0.3	7
	Frequency range		945	–	960	-50	1
	E-UTRA Band 41		F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 3, 34		F_{DL_low}	–	F_{DL_high}	-50	1	3
	Frequency range		703	–	799	-50	1
	Frequency range		799	–	803	-40	1	3
	Frequency range		1839.9	–	1879.9	-50	1	3
CA_1A-28A	E-UTRA Band 5, 7, 8, 18, 19, 20, 26, 27, 31, 32, 38, 40, 41		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 22, 42, 43		F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 3, 34		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 11, 21		F_{DL_low}	–	F_{DL_high}	-50	1	5, 21
	E-UTRA Band 1, 65		F_{DL_low}	–	F_{DL_high}	-50	1	5, 6
	Frequency range		470	–	694	-42	8	3, 22
	Frequency range		470	–	710	-26.2	6	23
	Frequency range		758	–	773	-32	1	3
	Frequency range		773	–	803	-50	1
	Frequency range		662	–	694	-26.2	6	3
	Frequency range		1880		1895	-40	1	3,12
	Frequency range		1895		1915	-15.5	5	3, 12, 13
	Frequency range		1915		1920	+1.6	5	3, 12, 13
	Frequency range		1839.9	–	1879.9	-50	1	3
	Frequency range		1884.5	–	1915.7	-41	0.3	5, 7
CA_1A-42A	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 38, 40, 41, 44, 65, 67		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3, 34		F_{DL_low}	–	F_{DL_high}	-50	1	3
	Frequency range		1880		1895	-40	1	3,12
	Frequency range		1895		1915	-15.5	5	3, 12, 13
	Frequency range		1915		1920	+1.6	5	3, 12, 13
	Frequency range		1839.9	–	1879.9	-50	1	3
	Frequency range		1884.5	–	1915.7	-41	0.3	3, 7
CA_2A-4A	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 22, 24, 26, 27, 28, 29, 30, 41, 66, 70		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42, 43		F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-5A	E-UTRA Band 4, 5, 10, 12, 13, 14, 17, 24, 28, 29, 30, 42, 70		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 26		859	–	869	-27	1
	E-UTRA Band 41, 43		F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-7A	E-UTRA Band 2, 4, 5, 7, 10, 12, 13, 14, 17, 26, 27, 29, 30, 42, 65, 66, 70		F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-7A	E-UTRA Band 43		F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-12A	E-UTRA Band 5, 13, 14, 17, 24, 26, 27, 30, 41		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 12, 25		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 4, 10, 70		F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-13A	E-UTRA Band 4, 5,10,12,13,17, 22, 26, 27, 29, 41, 42, 66, 70		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2,14, 25		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 24, 30, 43		F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range		769	–	775	-35	0.00625	3
	Frequency range		799	–	805	-35	0.00625	3, 9
CA_3A-5A	E-UTRA Band 1, 5, 7, 8, 22, 28, 31, 38, 40, 42, 43, 65		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3,34		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 26		859	–	869	-27	1
CA_3A-7A	E-UTRA Band 1, 5, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 40, 43, 44, 65, 67		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 22, 42		F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range		2570	–	2575	+1.6	5	3, 13, 14
	Frequency range		2575	–	2595	-15.5	5	3, 13, 14
	Frequency range		2595	–	2620	-40	1	3, 14
CA_3A-8A	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40, 44, 65, 67		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3, 8		F_{DL_low}	–	F_{DL_high}	-50	1	2, 3
	E-UTRA band 11, 21		F_{DL_low}	–	F_{DL_high}	-50	1	10,11
	E-UTRA band 7, 22, 41, 42, 43		F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range		1884.5	–	1915.7	-41	0.3	4, 10, 11
	Frequency range		860	–	890	-40	1	3,11,17
CA_3A-19A	E-UTRA Band 1, 11, 21, 28, 40, 65		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 34		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42		F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range		860	–	890	-40	1	3, 8
	Frequency range		945	–	960	-50	1
	Frequency range		1884.5	–	1915.7	-41	0.3	3, 4
	Frequency range		1839.9	–	1879.9	-50	1	3
	Frequency range		2545	–	2575	-50	1
	Frequency range		2595	–	2645	-50	1
CA_3A-20A	E-UTRA Band 1, 7, 8, 31, 32, 33, 34, 40, 43, 65, 67		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3, 20		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 38, 42		F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range		758	–	788	-50	1
CA_3A-21A	E-UTRA Band 1, 18, 19, 28, 34, 40, 65		F_{DL_low}	–	FDL_high	-50	1
	E-UTRA Band 42		F_{DL_low}	–	FDL_high	-50	1	2
	Frequency range		945	–	960	-50	1
	Frequency range		1884.5	–	1915.7	-41	0.3	4
	Frequency range		1839.9	–	1879.9	-50	1
	Frequency range		2545	–	2575	-50	1
	Frequency range		2595	–	2645	-50	1
CA_3A-26A	E-UTRA Band 1, 5, 7, 26, 34, 39, 40, 43, 65		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA band 11, 18, 19, 21		F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA band 22, 41, 42		F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range		1884.5	–	1915.7	-41	0.3	4, 10
	Frequency range		703	–	799	-50	1
	Frequency range		799	–	803	-40	1	3
	Frequency range		851	–	859	-53	0.00625	15
	Frequency range		945	–	960	-50	1
	Frequency range		1839.9	–	1879.9	-50	1
CA_3A-40A	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 33, 34, 38, 39, 41, 43, 44. 45, 65, 67, 68, 69		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 42		F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range		1884.5	–	1915.7	-41	0.3	4
	Frequency range		1475	–	1518	-50	1
	Frequency range		3300	–	4200	-50	1	2
	Frequency range		4400	–	5000	-50	1	2
CA_3A-42A	E-UTRA Band 1, 5, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 40, 41, 44, 45, 65, 67		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3		F_{DL_low}	–	F_{DL_high}	-50	1	15
	E-UTRA Band 11, 18, 19, 21		F_{DL_low}	–	F_{DL_high}	-50	1	13
	Frequency range		1884.5	–	1915.7	-41	0.3	8, 13
CA_4A-5A	E-UTRA Band 2, 4, 5, 7, 10, 12, 13, 14, 17, 24, 25, 28, 29, 30, 43, 70		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 26		859	–	869	-27	1
	E-UTRA band 41, 42		F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_4A-7A	E-UTRA Band 2, 4, 5, 7, 10, 12, 13, 14, 17, 26, 27, 28, 29, 30, 43, 66		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 42		F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range		2570	–	2575	+1.6	5	3, 13, 14
	Frequency range		2575	–	2595	-15.5	5	3, 13, 14
	Frequency range		2595	–	2620	-40	1	3, 14
CA_4A-12A	E-UTRA Band 2, 5, 7,13, 14, 17, 22, 24, 25, 26, 27, 30, 41, 43		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10, 42, 66, 70		F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12		F_{DL_low}	–	F_{DL_high}	-50	1	3
CA_4A-13A	E-UTRA Band 2,4, 5, 7, 10,12,13,17, 22, 25, 26, 27, 29, 41, 43, 66, 70		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 14		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 24, 30, 42		F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range		769	–	775	-35	0.00625	3
	Frequency range		799	–	805	-35	0.00625	3, 9
CA_4A-17A	E-UTRA Band 2, 5, 7,13, 14, 17, 22, 24, 25, 26, 27, 30, 41, 43		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 4, 10, 42, 66, 70		F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 12		F_{DL_low}	–	F_{DL_high}	-50	1	3
CA_5A-7A	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 12, 13, 14, 17, 22, 28, 29, 30, 31, 40, 42, 43, 65, 66		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 26		859	–	869	-27	1
	Frequency range		2570	–	2575	+1.6	5	3, 13, 14
	Frequency range		2575	–	2595	-15.5	5	3, 13, 14
	Frequency range		2595	–	2620	-40	1	3, 14
CA_5A-12A	E-UTRA Band 2, 5, 13, 14, 17, 22, 24, 25, 30, 31, 42, 43		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 4, 10, 41, 66, 70		F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA band 26		859	–	869	-27	1
	E-UTRA band 12		F_{DL_low}	–	F_{DL_high}	-50	1	3
CA_5A-17A	E-UTRA Band 2, 5, 13, 14, 17, 22, 24, 25, 30, 31, 42, 43		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 4, 10, 41, 66, 70		F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA band 26		859	–	869	-27	1
	E-UTRA band 12		F_{DL_low}	–	F_{DL_high}	-50	1	3
CA_5A-40A	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 21, 28, 31, 34, 38, 42, 43, 45, 65		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 26		859	–	869	-27	1
	E-UTRA band 41		F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range		1884.5	–	1915.7	-41	0.3	4
	Frequency range		1475	–	1518	-50	1
	Frequency range		3300	–	4200	-50	1	2
	Frequency range		4400	–	5000	-50	1	2
CA_7A-20A	E-UTRA Band 1,3, 7, 8, 22, 28, 31, 32, 33, 34, 40, 43, 65, 67		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20		F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42		F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range		2570	–	2575	+1.6	5	3, 13, 14
	Frequency range		2575	–	2595	-15.5	5	3, 13, 14
	Frequency range		2595	–	2620	-40	1	3, 14
CA_7A-28A	E-UTRA Band 2, 3, 5, 7, 8, 20, 26, 27, 31, 34, 40		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 1, 4, 10, 22, 42, 43, 65, 66		F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 1		F_{DL_low}	–	F_{DL_high}	-50	1	5, 6
	Frequency range		758	–	773	-32	1	3
	Frequency range		773	–	803	-50	1
	Frequency range		2570	–	2575	+1.6	5	3, 13, 14
	Frequency range		2575	–	2595	-15.5	5	3, 13, 14
	Frequency range		2595	–	2620	-40	1	3, 14
CA_8A-41A	E-UTRA Band 1, 28, 34, 39, 40, 45, 65,		FDL_low	–	FDL_high	-50	1
	E-UTRA band 3, 42		FDL_low	–	FDL_high	-50	1	2
	E-UTRA band 11, 21		FDL_low	–	FDL_high	-50	1	23, 30
	Frequency range		1884.5	–	1915.7	-41	0.3	8, 23, 30
CA_18A-28A	E-UTRA Band 11, 21		F_{DL_low}	–	F_{DL_high}	-50	1	5, 21
	E-UTRA Band 1, 65		F_{DL_low}	–	F_{DL_high}	-50	1	5, 6
	E-UTRA Band 42, 43		F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 34		F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range		470	–	710	-26.2	6	23
	Frequency range		758	–	773	-32	1	3
	Frequency range		773	–	799	-50	1
	Frequency range		799	–	803	-40	1	3
	Frequency range		860	–	890	-40	1
	Frequency range		945	–	960	-50	1	3
	Frequency range		1884.5	–	1915.7	-41	0.3	4
	Frequency range		1839.9	–	1879.9	-50	1
	Frequency range		2545	–	2575	-50	1
	Frequency range		2595	–	2645	-50	1
CA_19A-21A	E-UTRA Band 1, 18, 19, 28, 34, 42, 65		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 11		F_{DL_low}	–	F_{DL_high}	-50	1	3, 16
	E-UTRA Band 21		F_{DL_low}	–	F_{DL_high}	-50	1	16
	Frequency range		860	–	890	-40	1	3, 8
	Frequency range		945	–	960	-50	1
	Frequency range		1884.5	–	1915.7	-41	0.3	4
	Frequency range		1839.9	–	1879.9	-50	1
	Frequency range		2545	–	2575	-50	1
	Frequency range		2595	–	2645	-50	1
CA_18A-28A	E-UTRA Band 11, 21		F_{DL_low}	–	F_{DL_high}	-50	1	5, 21
	E-UTRA Band 1, 65		F_{DL_low}	–	F_{DL_high}	-50	1	5, 6
	E-UTRA Band 42, 43		F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 3, 34, 40		F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range		470	–	710	-26.2	6	23
	Frequency range		758	–	773	-32	1	3
	Frequency range		773	–	799	-50	1
	Frequency range		799	–	803	-40	1	3
	Frequency range		860	–	890	-40	1
	Frequency range		945	–	960	-50	1	3
	Frequency range		1884.5	–	1915.7	-41	0.3	4
	Frequency range		2545	–	2575	-50	1
	Frequency range		2595	–	2645	-50	1
CA_19A-21A	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 42, 65		F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 11		F_{DL_low}	–	F_{DL_high}	-50	1	3, 16
	E-UTRA Band 21		F_{DL_low}	–	F_{DL_high}	-50	1	16
	Frequency range		860	–	890	-40	1	3, 8
	Frequency range		945	–	960	-50	1
	Frequency range		1884.5	–	1915.7	-41	0.3	4
	Frequency range		2545	–	2575	-50	1
	Frequency range		2595	–	2645	-50	1
CA_19A-42A	E-UTRA Band 1, 11, 21, 28, 34, 40, 42, 65		F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range		945	–	960	-50	1
	Frequency range		1839.9	–	1879.9	-50	1
	Frequency range		1884.5	–	1915.7	-41	0.3	4
	Frequency range		2545	–	2575	-50	1
	Frequency range		2595	–	2645	-50	1
CA_21A-28A	E-UTRA Band 1, 42, 65		F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 1		F_{DL_low}	–	F_{DL_high}	-50	1	5, 6
	E-UTRA Band 3, 18, 19, 34, 40		F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range		470	–	710	-26.2	6	23
	Frequency range		773	–	803	-50	1
	Frequency range		945	–	960	-50	1
	Frequency range		1884.5	–	1915.7	-41	0.3	4, 5
	Frequency range		2545	–	2575	-50	1
	Frequency range		2595	–	2645	-50	1
CA_21A-42A	E-UTRA Band 1, 18, 19, 28, 34, 40, 42, 65		F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range		945	–	960	-50	1
	Frequency range		1839.9	–	1879.9	-50	1
	Frequency range		1884.5	–	1915.7	-41	0.3	4
	Frequency range		2545	–	2575	-50	1
	Frequency range		2595	–	2645	-50	1
CA 39A-41A	E-UTRA Band 1, 8, 26, 34, 40, 42, 44		F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range		1805	–	1855	-40	1	20
	Frequency range		1855	–	1880	-15.5	5	3, 13, 20
CA_39A-41C	E-UTRA Band 1, 8, 26, 34, 40, 42, 44		F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range		1805	–	1855	-40	1	20
	Frequency range		1855	–	1880	-15.5	5	3, 13, 20
CA_39C-41A	E-UTRA Band 34, 40, 42, 44		F_{DL_low}	–	F_{DL_high}	-50	1
CA_41A-42A	E-UTRA Band 1, 3, 5, 8, 26, 28, 33, 34, 39, 40, 44, 45, 65,	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}		–	F_{DL_high}	-50	1	18
	Frequency range	1839.9			1879.9	-50	1	18
	Frequency range	1884.5			1915.7	-41	0.3	4, 18
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. In case the exceptions are allowed due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3 or 4 for the 2^nd, 3^rd or 4^th harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3: These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the aggregated channel bandwidth. NOTE 4:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. NOTE 5:Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. NOTE 6: As exceptions, measurements with a level up to the applicable requirement of -36 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 3^rdharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 3^rd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 7: Applicable when NS_05 in section 6.6.3.3.3.2 is signalled by the network. NOTE 8: Applicable when NS_08 in subclause 6.6.3.3.3.4 is signalled by the network NOTE 9: Whether the applicable frequency range should be 793-805MHz instead of 799-805MHz is TBD. NOTE10: This requirement applies for 5, 10, 15 and 20 MHz E-UTRA channel bandwidth allocated within 1744.9MHz and 1784.9MHz. NOTE 11: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 12: This requirement is applicable for any channel bandwidths within the range 1920 – 1980 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE13: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. NOTE14:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE 15:Applicable when NS_15 in subclause 6.6.3.3.3.10 is signalled by the network. NOTE 16:Applicable when NS_09 in subclause 6.6.3.3.3.5 is signalled by the network NOTE 17: This requirement is applicable only when Band 3 transmission frequency is less than or equal to 1765 MHz. NOTE 18: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz NOTE 19: Void NOTE 20: This requirement is only applicable for carriers with bandwidth confined within 1885-1920 MHz (requirement for carriers with at least 1RB confined within 1880 – 1885 MHz is not specified). This requirement applies for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1892.5 – 1894.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1895 – 1903 MHz. NOTE 21: As exceptions, measurements with a level up to the applicable requirement of -38 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 2^ndharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 2^nd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 22: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies. NOTE 23: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48.

Table 6.6.3.2A.0-1d: Requirements for dual-uplink inter-band carrier aggregation limits for Rel-15

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)				Maximum Level (dBm)	MBW (MHz)	NOTE
CA_1A-3A	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 38, 40, 41, 43, 44, 50, 51, 65, 67, 72, 73, 74, 75, 76 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 22, 42, 52 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
CA_1A-5A	E-UTRA Band 1, 5, 7, 8, 22, 28, 31, 38, 40, 42, 43, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3,34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 26	859		–	869	-27	1
	E-UTRA band 41, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_1A-7A	E-UTRA Band 1, 5, 7, 8, 20, 22, 26, 27, 28, 31,32, 40, 42, 43, 50, 51, 52, 65, 67, 72, 74, 75, 76 NR Band n78	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_1A-8A	E-UTRA Band 1, 20, 28, 31, 32, 38, 40, 50, 51, 65, 67, 72, 73, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 7, 22, 41, 42, 43, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 8, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	11
	Frequency range	860		–	890	-40	1	3, 11
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
CA_1A-11A	E-UTRA Band 1, 3, 11, 18, 19, 21, 28, 34, 40,42, 65 NR Band n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_1A-18A	E-UTRA Band 1, 3, 11, 21, 40,42, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	758		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
	Frequency range	860		–	890	-40	1
	Frequency range	945		–	960	-50	1
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_1A-19A	E-UTRA Band 1, 3, 11, 21, 28, 40,42, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_1A-20A	E-UTRA Band 1, 3, 7, 8, 22, 31, 32, 34, 40, 43, 50, 51, 65, 67, 68, 72, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 38, 42, 69 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	758		–	788	-50	1
CA_1A-21A	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1, 3, 18, 19, 28, 34, 40,42, 65 NR Band n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	945		–	960	-50	1
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_1A-26A	E-UTRA Band 1, 5, 7, 11, 18, 19, 21, 22, 26, 31, 38, 40, 42, 43, 50, 51, 65, 73, 74 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	1880		–	1895	-40	1	3, 12
	Frequency range	1895		–	1915	-15.5	5	3, 12, 13
	Frequency range	1915		–	1920	+1.6	5	3, 12, 13
	Frequency range	945		–	960	-50	1
	E-UTRA Band 41 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
CA_1A-28A	E-UTRA Band 3, 5, 7, 8, 18, 19, 20, 26, 27, 31, 38, 40, 41, 72, 73	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 22, 32, 42, 43, 50, 51, 52, 74, 75, 76 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	5, 21
	E-UTRA Band 1, 65	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	Frequency range	470		–	694	-42	8	3, 22
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	803	-50	1
	Frequency range	662		–	694	-26.2	6	3
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
CA_1A-41A	E-UTRA Band 1, 3, 5, 8, 26, 27, 28, 40, 42, 44, 45, 50, 51, 52, 65, 73, 74 NR Band n78	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	NR Band n77, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
	E-UTRA Band 11, 18, 19, 21	F_{DL_low}		–	F_{DL_high}	-50	1	30
CA_1A-42A	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 38, 40, 41, 44, 50, 51, 65, 67, 72, 73, 74, 75, 76 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
CA_2A-4A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 27, 28, 29, 30, 41, 50, 51, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 42, 43	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_2A-5A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 28, 29, 30, 42, 50, 51, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 26	859		–	869	-27	1
	E-UTRA Band 41, 43	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_2A-7A	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 26, 27, 29, 30, 42, 50, 51, 65, 66, 70, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
CA_2A-7A	E-UTRA Band 43	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_2A-12A	E-UTRA Band 5, 13, 14, 17, 24, 26, 27, 30, 41, 50, 71, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 2, 12, 25, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 4, 51, 66, 70	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_2A-13A	E-UTRA Band 4, 5,12,13,17, 22, 26, 27, 29, 41, 42, 50, 51, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 2,14, 25	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 24, 30, 43	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	769		–	775	-35	0.00625	3
	Frequency range	799		–	805	-35	0.00625	3
CA_2A-49A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 50, 51, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
CA_3A-5A	E-UTRA Band 1, 5, 7, 8, 28, 31, 38, 40, 43, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3,34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 42, 52	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859		–	869	-27	1
CA_3A-7A	E-UTRA Band 1, 5, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 40, 43, 44, 50, 51, 65, 67, 72, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 22, 42, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_3A-8A	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40, 44, 50, 51, 65, 67, 72, 73, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 8	F_{DL_low}		–	F_{DL_high}	-50	1	2, 3
	E-UTRA band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	10,11
	E-UTRA band 7, 22, 41, 42, 43, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 10, 11
	Frequency range	860		–	890	-40	1	3,11,17
CA_3A-18A	E-UTRA Band 1, 3, 11, 21, 28, 34, 40,65 NR Bandn79	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78,	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_3A-19A	E-UTRA Band 1, 11, 21, 28, 40, 65	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 42 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	3, 4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_3A-20A	E-UTRA Band 1, 7, 8, 31, 32, 33, 34, 40, 43, 50, 51, 65, 67, 72, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3, 20	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 38, 42, 52	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	758		–	788	-50	1
CA_3A-21A	E-UTRA Band 1, 18, 19, 28, 34, 40,65 NR Band n79	FDL_{_low}		–	FDL_{_high}	-50	1
	E-UTRA band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 42 NR Band n77, n78,	FDL_{_low}		–	FDL_{_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_3A-26A	E-UTRA Band 1, 5, 7, 11, 18, 19, 21, 26, 34, 39, 40, 43, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 22, 41, 42 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
	Frequency range	945		–	960	-50	1
CA_3A-28A	E-UTRA Band 1, 11, 18, 19, 21, 22, 32, 42, 43, 50, 51, 52, 65, 74, 75, 76 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	E-UTRA band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 5, 7, 8, 20, 26, 27, 31, 34, 38, 40, 41, 72, 73	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	803	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 5
CA_3A-40A	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 33, 34, 38, 39, 41, 43, 44. 45, 50, 51, 65, 67, 68, 69, 72, 73, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 42, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3
CA_3A-41A	E-UTRA Band 1, 5, 8, 26, 28, 33, 34, 39, 40, 44, 45, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 11, 18, 19, 21	F_{DL_low}		–	F_{DL_high}	-50	1	18
	NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5			1915.7	-41	0.3	4, 18
CA_3A-42A	E-UTRA Band 1, 5, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 40, 41, 44, 45, 50, 51, 65, 67, 72, 73, 74, 75, 76 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 11, 18, 19, 21	F_{DL_low}		–	F_{DL_high}	-50	1	13
	Frequency range	1884.5		–	1915.7	-41	0.3	4
CA_4A-5A	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 24, 25, 28, 29, 30, 43, 50, 51, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 26	859		–	869	-27	1
	E-UTRA band 41, 42	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_4A-7A	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 26, 27, 28, 29, 30, 43, 50, 51, 66, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 42	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_4A-12A	E-UTRA Band 2, 5, 7,13, 14, 17, 24, 25, 26, 27, 30, 41, 43, 50, 71, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 4, 22, 42, 51, 66, 70	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_4A-13A	E-UTRA Band 2,4, 5, 7, 12,13,17, 25, 26, 27, 29, 41, 43, 50, 51, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 14	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 24, 22, 30, 42	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	769		–	775	-35	0.00625	3
	Frequency range	799		–	805	-35	0.00625	3
CA_4A-17A	E-UTRA Band 2, 5, 7,13, 14, 17, 24, 25, 26, 27, 30, 41, 43, 50, 71, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 4, 22, 42, 51, 66, 70	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_5A-7A	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 22, 28, 29, 30, 31, 40, 42, 43, 50, 51, 65, 66, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 52 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859		–	869	-27	1
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_5A-12A	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 30, 31,43, 50, 71, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 4, 22, 41, 42, 51, 66, 70	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859		–	869	-27	1
	E-UTRA band 12, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_5A-17A	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 30, 31,43, 50, 71, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 4, 22, 41, 42, 51, 66, 70	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859		–	869	-27	1
	E-UTRA band 12, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_5A-40A	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 21, 28, 31, 34, 38, 42, 43, 45, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 26	859		–	869	-27	1
	E-UTRA band 41, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	4
CA_7A-8A	E-UTRA Band 1, 20, 27, 28, 31, 32, 34, 40, 50, 51, 65, 67, 68, 72, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 7, 22, 42, 43, 52 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}		–	F_{DL_high}	-50	1	3
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_7A-20A	E-UTRA Band 1,3, 7, 8, 22, 28, 31, 32, 33, 34, 40, 43, 50, 51, 65, 67, 72, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 42, 52 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_7A-26A	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 22, 29, 30, 31, 40, 42, 43, 65, 66, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	7
CA_7A-28A	E-UTRA Band 2, 3, 5, 7, 8, 20, 26, 27, 31, 34, 40, 72 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 1, 4, 22, 32, 42, 43, 50, 51, 52, 65, 66, 74, 75, 76 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	803	-50	1
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_8A-39A	E-UTRA Band 1, 40, 45, 50, 51, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 22, 41, 42, 52	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_8A-41A	E-UTRA Band 1, 28, 34, 39, 40, 45, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 42, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	11
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 11
CA_11A-18A	E-UTRA Band 1, 3, 11, 21, 28, 40, 34, 42, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	860		–	890	-40	1	3
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
	Frequency range	945		–	960	-50	1
CA_11A-26A	E-UTRA Band 1, 3, 11, 18, 19, 21, 26, 28, 34, 40, 42, 65	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1	2
	Frequency range	2595		–	2645	-50	1
	Frequency range	945		–	960	-50	1
CA_18A-28A	E-UTRA Band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	5, 21
	E-UTRA Band 1, 65	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	E-UTRA Band 42, 43 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 3, 34, 40	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
	Frequency range	860		–	890	-40	1
	Frequency range	945		–	960	-50	1	3
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_19A-21A	E-UTRA Band 1, 3, 28, 34, 40, 42, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78,	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_19A-42A	E-UTRA Band 1, 3, 11, 21, 28, 34, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_21A-28A	E-UTRA Band 1, 42, 65 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	E-UTRA Band 3, 18, 19, 34, 40 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	773		–	803	-50	1
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 5
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_21A-42A	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_26A-46A	E-UTRA Band 1, 2, 3, 4, 5, 11, 12, 13, 14, 17, 18,19, 21, 24, 25, 26, 29, 30, 31, 34, 39, 40, 42, 43, 48, 65, 66, 70, 71, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 41	F_{DL_low}		–	F_{DL_high}	-50	1	1, 2
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	3
CA_26A-48A	E-UTRA Band 1, 2, 3, 4, 5, 11, 12, 13, 14, 17, 18,19, 21, 24, 25, 26, 29, 30, 31, 34, 39, 40, 50, 51, 65, 66, 70, 71, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 41	F_{DL_low}		–	F_{DL_high}	-50	1	1, 2
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	3
CA_28A-41A	E-UTRA Band E-UTRA Band 1, 4, 22, 32, 42, 45, 43, 48, 52, 65, 66 NR Band n77, n78, n79	F_{DL_low}	–		F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}	–		F_{DL_high}	-50	1	5, 6
	E-UTRA band 2, 3, 5, 8, 20, 25, 26, 27, 31, 33, 34, 40	F_{DL_low}	–		F_{DL_high}	-50	1
	E-UTRA band 11, 21	F_{DL_low}	–		F_{DL_high}	-50	1	5, 18, 21
	E-UTRA band 9, 18, 19	F_{DL_low}	–		F_{DL_high}	-50	1	5, 18
	Frequency range	470	–		694	-42	8	3, 22
	Frequency range	470	–		710	-26.2	6	23
	Frequency range	662	–		694	-26.2	6	3
	Frequency range	758	–		773	-32	1	3
	Frequency range	773	–		803	-50	1
	Frequency range	1884.5	–		1915.7	-41	0.3	4, 5, 18
CA_28A-42A	E-UTRA Band 1, 4, 32, 50, 51, 66, 65, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	E-UTRA Band 2, 3, 5, 7, 8, 18, 19, 20, 25, 26, 27, 31, 34, 38, 40, 41, 72, 73 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	5, 21
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	803	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 5
CA_39A-41C	E-UTRA Band 1, 8, 26, 34, 40, 42, 44, 50, 51, 52, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1805		–	1855	-40	1	20
	Frequency range	1855		–	1880	-15.5	5	3, 13, 20
CA_40A-42A	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 11, 12, 13, 14, 17, 18, 19, 20, 21, 24, 25, 26, 27, 28, 29, 31, 32, 33, 34, 38, 39, 41, 44, 45, 50, 51, 65, 66, 67, 68, 69, 70, 72, 73, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	8
CA_41A-42A	E-UTRA Band 1, 3, 5, 8, 26, 28, 33, 34, 39, 40, 44, 45, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}		–	F_{DL_high}	-50	1	18
	NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5			1915.7	-41	0.3	4, 18
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. In case the exceptions are allowed due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3 or 4 for the 2^nd, 3^rd or 4^th harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3: These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the aggregated channel bandwidth. NOTE 4:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. NOTE 5:Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. NOTE 6: As exceptions, measurements with a level up to the applicable requirement of -36 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 3^rdharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 3^rd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 7: Void NOTE 8: Void NOTE 9: Void NOTE10: Void NOTE 11: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 12: This requirement is applicable for any channel bandwidths within the range 1920 – 1980 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE13: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. NOTE14:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE 15:Void NOTE 16:Void NOTE 17: This requirement is applicable only when Band 3 transmission frequency is less than or equal to 1765 MHz. NOTE 18: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz NOTE 19: Void NOTE 20: This requirement is only applicable for carriers with bandwidth confined within 1885-1920 MHz (requirement for carriers with at least 1RB confined within 1880 – 1885 MHz is not specified). This requirement applies for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1892.5 – 1894.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1895 – 1903 MHz. NOTE 21: As exceptions, measurements with a level up to the applicable requirement of -38 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 2^ndharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 2^nd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 22: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies. NOTE 23: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48. NOTE 24: Void NOTE 25: Void

Table 6.6.3.2A.0-1e: Requirements for dual-uplink inter-band carrier aggregation limits for Rel-16

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)				Maximum Level (dBm)	MBW (MHz)	NOTE
CA_1A-3A	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 38, 40, 41, 43, 44, 50, 51, 65, 67, 72, 73, 74, 75, 76 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 22, 42, 52 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
CA_1A-5A	E-UTRA Band 1, 5, 7, 8, 22, 28, 31, 38, 40, 42, 43, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3,34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 26	859		–	869	-27	1
	E-UTRA band 41, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_1A-7A	E-UTRA Band 1, 5, 7, 8, 20, 22, 26, 27, 28, 31,32, 40, 42, 43, 50, 51, 52, 65, 67, 72, 74, 75, 76 NR Band n78	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_1A-8A	E-UTRA Band 1, 20, 28, 31, 32, 38, 40, 50, 51, 65, 67, 72, 73, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 7, 22, 41, 42, 43, 52 NR Band n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 8, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	11
	Frequency range	860		–	890	-40	1	3, 11
	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
CA_1A-11A	E-UTRA Band 1, 3, 11, 18, 19, 21, 28, 34, 40, 42, 65 NR Band , n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_1A-18A	E-UTRA Band 1, 3, 11, 21, 40, 42, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	758		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
	Frequency range	860		–	890	-40	1
	Frequency range	945		–	960	-50	1
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_1A-19A	E-UTRA Band 1, 3, 11, 21, 28, 40, 42, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_1A-20A	E-UTRA Band 1, 3, 7, 8, 22, 31, 32, 34, 40, 43, 50, 51, 65, 67, 68, 72, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 38, 42, 69 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	758		–	788	-50	1
CA_1A-21A	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 42, 65 NR Band n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	945		–	960	-50	1
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_1A-26A	E-UTRA Band 1, 5, 7, 11, 18, 19, 21, 22, 26, 31, 38, 40, 42, 43, 50, 51, 65, 73, 74 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	1880		–	1895	-40	1	3, 12
	Frequency range	1895		–	1915	-15.5	5	3, 12, 13
	Frequency range	1915		–	1920	+1.6	5	3, 12, 13
	Frequency range	945		–	960	-50	1
	E-UTRA Band 41 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
CA_1A-28A	E-UTRA Band 3, 5, 7, 8, 18, 19, 20, 26, 27, 31, 38, 40, 41, 72, 73	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 22, 32, 42, 43, 50, 51, 52, 74, 75, 76 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	5, 21
	E-UTRA Band 1, 65	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	Frequency range	470		–	694	-42	8	3, 22
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	803	-50	1
	Frequency range	662		–	694	-26.2	6	3
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
CA_1A-41A	E-UTRA Band 1, 3, 5, 8, 26, 27, 28, 40, 42, 44, 45, 50, 51, 52, 65, 73, 74 NR Band n78	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	NR Band n77, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
	E-UTRA Band 11, 18, 19, 21	F_{DL_low}		–	F_{DL_high}	-50	1	30
CA_1A-42A	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 38, 40, 41, 44, 50, 51, 65, 67, 72, 73, 74, 75, 76 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
CA_2A-4A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 27, 28, 29, 30, 41, 50, 51, 53, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 42, 43, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_2A-5A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 28, 29, 30, 42, 50, 51, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 26	859		–	869	-27	1
	E-UTRA Band 41, 43, 53 NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_2A-7A	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 26, 27, 29, 30, 42, 50, 51, 65, 66, 70, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
CA_2A-7A	E-UTRA Band 43	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_2A-12A	E-UTRA Band 5, 13, 14, 17, 24, 26, 27, 30, 41, 50, 53, 71, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 2, 12, 25, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 4, 51, 66, 70, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_2A-13A	E-UTRA Band 4, 5,12,13,17, 22, 26, 27, 29, 41, 42, 50, 51, 53, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 2,14, 25	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 24, 30, 43, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	769		–	775	-35	0.00625	3
	Frequency range	799		–	805	-35	0.00625	3
CA_2A-14A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 27, 29, 30, 41, 48, 53, 66, 70, 71, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}		–	F_{DL_high}	-50	1	3
	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	769		–	775	-35	0.00625	3
	Frequency range	799		–	805	-35	0.00625	3, 9
CA_2A-48A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 50, 51, 53, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
CA_2A-49A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 50, 51, 53, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
CA_3A-5A	E-UTRA Band 1, 5, 7, 8, 28, 31, 38, 40, 43, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3,34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 42, 52	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859		–	869	-27	1
CA_3A-7A	E-UTRA Band 1, 5, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 40, 43, 44, 50, 51, 65, 67, 72, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 22, 42, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_3A-8A	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40, 44, 50, 51, 65, 67, 72, 73, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 8	F_{DL_low}		–	F_{DL_high}	-50	1	2, 3
	E-UTRA band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	10,11
	E-UTRA band 7, 22, 41, 42, 43, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 10, 11
	Frequency range	860		–	890	-40	1	3,11,17
CA_3A-11A	E-UTRA Band 1, 18, 19, 28, 34, 40, 65	FDL_{_low}		–	FDL_{_high}	-50	1
	E-UTRA band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 42	FDL_{_low}		–	FDL_{_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_3A-18A	E-UTRA Band 1, 3, 11, 21, 28, 34, 40, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78,	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_3A-19A	E-UTRA Band 1, 11, 21, 28, 40, 65	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 42 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	3, 4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_3A-20A	E-UTRA Band 1, 7, 8, 31, 32, 33, 34, 40, 43, 50, 51, 65, 67, 72, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3, 20	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 38, 42, 52	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	758		–	788	-50	1
CA_3A-21A	E-UTRA Band 1, 18, 19, 28, 34, 40, 65 NR Band n79	FDL_{_low}		–	FDL_{_high}	-50	1
	E-UTRA band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 42 NR Band n77, n78,	FDL_{_low}		–	FDL_{_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_3A-26A	E-UTRA Band 1, 5, 7, 11, 18, 19, 21, 26, 34, 39, 40, 43, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 22, 41, 42 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
	Frequency range	945		–	960	-50	1
CA_3A-28A	E-UTRA Band 1, 11, 18, 19, 21, 22, 32, 42, 43, 50, 51, 52, 65, 74, 75, 76 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	E-UTRA band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 5, 7, 8, 20, 26, 27, 31, 34, 38, 40, 41, 72, 73	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	803	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 5
CA_3A-40A	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 33, 34, 38, 39, 41, 43, 44. 45, 50, 51, 65, 67, 68, 69, 72, 73, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 42, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3
CA_3A-41A	E-UTRA Band 1, 5, 8, 26, 28, 33, 34, 39, 40, 44, 45, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 11, 18, 19, 21	F_{DL_low}		–	F_{DL_high}	-50	1	18
	NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5			1915.7	-41	0.3	4, 18
CA_3A-42A	E-UTRA Band 1, 5, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 40, 41, 44, 45, 50, 51, 65, 67, 72, 73, 74, 75, 76 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 11, 18, 19, 21	F_{DL_low}		–	F_{DL_high}	-50	1	13
	Frequency range	1884.5		–	1915.7	-41	0.3	4
CA_4A-5A	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 24, 25, 28, 29, 30, 43, 50, 51, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 26	859		–	869	-27	1
	E-UTRA band 41, 42, 53 NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_4A-7A	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 26, 27, 28, 29, 30, 43, 50, 51, 66, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 42	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_4A-12A	E-UTRA Band 2, 5, 7,13, 14, 17, 24, 25, 26, 27, 30, 41, 43, 50, 53, 71, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 4, 22, 42, 51, 66, 70, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_4A-13A	E-UTRA Band 2,4, 5, 7, 12,13,17,25, 26, 27, 29, 41, 43, 50, 51, 53, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 14	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 24, 30, 42, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	769		–	775	-35	0.00625	3
	Frequency range	799		–	805	-35	0.00625	3
CA_4A-17A	E-UTRA Band 2, 5, 7,13, 14, 17, 24, 25, 26, 27, 30, 41, 43, 50, 53, 71, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 4, 22, 42, 51, 66, 70, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_4A-28A	E-UTRA Band 2, 5, 7, 14, 24, 25, 26, 27, 30, 41, 53, 70, 71	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 4, 42, 43, 48, 50, 51, 66, 74	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	758			773	-32	1	3
	Frequency range	773			803	-50	1
CA_5A-7A	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 22, 28, 29, 30, 31, 40, 42, 43, 50, 51, 65, 66, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 52 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859		–	869	-27	1
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_5A-12A	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 30, 31, 43, 50, 53, 71, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 4, 22, 41, 42, 51, 66, 70, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859		–	869	-27	1
	E-UTRA band 12, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_5-17	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 30, 31, 43, 50, 71, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 4, 22, 41, 42, 51, 53, 66, 70, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859		–	869	-27	1
	E-UTRA band 12, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_5A-40A	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 21, 28, 31, 34, 38, 42, 43, 45, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 26	859		–	869	-27	1
	E-UTRA band 41, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	4
CA_7A-8A	E-UTRA Band 1, 20, 27, 28, 31, 32, 34, 40, 50, 51, 65, 67, 68, 72, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 7, 22, 42, 43, 52 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}		–	F_{DL_high}	-50	1	3
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_7A-20A	E-UTRA Band 1,3, 7, 8, 22, 28, 31, 32, 33, 34, 40, 43, 50, 51, 65, 67, 72, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 42, 52 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	2570		–	2575	+1.6	5	2, 3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	2, 3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_7A-26A	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 22, 29, 30, 31, 40, 42, 43, 65, 66, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	7
CA_7A-28A	E-UTRA Band 2, 3, 5, 7, 8, 20, 26, 27, 31, 34, 40, 72 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 1, 4, 22, 32, 42, 43, 50, 51, 52, 65, 66, 74, 75, 76 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	803	-50	1
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_8A-39A	E-UTRA Band 1, 28, 40, 45, 50, 51, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 22, 41, 42, 52 NR band n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_8A-41A	E-UTRA Band 1, 28, 34, 39, 40, 45, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 42, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	11
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 11
CA_11A-18A	E-UTRA Band 1, 3, 11, 21, 28, 34, 40, 42, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	860		–	890	-40	1	3
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
	Frequency range	945		–	960	-50	1
CA_11A-26A	E-UTRA Band 1, 3, 11, 18, 19, 21, 26, 28, 34, 40, 42, 65	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1	2
	Frequency range	2595		–	2645	-50	1
	Frequency range	945		–	960	-50	1
CA_13A-66A	E-UTRA Band 2, 4, 5, 12, 13, 17, 25, 26, 27, 29, 41, 50, 51, 53, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 14	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 24, 30, 48, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	769		–	775	-35	0.00625	3
	Frequency range	799		–	805	-35	0.00625	3, 9
CA_14A-30A	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 27, 29, 30, 41, 48, 53, 66, 70, 71, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	769		–	775	-35	0.00625	3
	Frequency range	799		–	805	-35	0.00625	3, 9
CA_14A-66A	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 27, 29, 30, 41, 53, 66, 70, 71, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 48, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	769		–	775	-35	0.00625	3
	Frequency range	799		–	805	-35	0.00625	3, 9
CA_18A-28A	E-UTRA Band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	5, 21
	E-UTRA Band 1, 65	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	E-UTRA Band 42, 43 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 3, 34, 40	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
	Frequency range	860		–	890	-40	1
	Frequency range	945		–	960	-50	1	3
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_19A-21A	E-UTRA Band 1, 3, 28, 34, 40, 42, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78,	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_19A-42A	E-UTRA Band 1, 3, 11, 21, 28, 34, 40, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_21A-28A	E-UTRA Band 1, 42, 65 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	E-UTRA Band 3, 18, 19, 34, 40 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	773		–	803	-50	1
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 5
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_21A-42A	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_25A-26A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 29, 30, 42, 48, 66, 70, 71, 85	F_{DL_low}		–	F_{DL_high}	-50	1
CA_25A-26A	E-UTRA Band 53 NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_25A-41A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 27, 28, 29, 30, 42, 45, 48, 66, 70, 71	F_{DL_low}		–	F_{DL_high}	-50	1
CA_25A-41A	E-UTRA Band 2, 25, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_26A-46A	E-UTRA Band 1, 2, 3, 4, 5, 11, 12, 13, 14, 17, 18,19, 21, 24, 25, 26, 29, 30, 31, 34, 39, 40, 42, 43, 48, 65, 66, 70, 71, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 41, 53, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	1, 2
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	3
CA_26A-48A	E-UTRA Band 1, 2, 3, 4, 5, 11, 12, 13, 14, 17, 18,19, 21, 24, 25, 26, 29, 30, 31, 34, 39, 40, 50, 51, 65, 66, 70, 71, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 41	F_{DL_low}		–	F_{DL_high}	-50	1	1,2
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	3
CA_28A-41A	E-UTRA Band E-UTRA Band 1, 4, 22, 32, 42, 45, 43, 48, 52, 65, 66 NR Band n77, n78, n79	F_{DL_low}	–		F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}	–		F_{DL_high}	-50	1	5, 6
	E-UTRA band 2, 3, 5, 8, 20, 25, 26, 27, 31, 33, 34, 40	F_{DL_low}	–		F_{DL_high}	-50	1
	E-UTRA band 11, 21	F_{DL_low}	–		F_{DL_high}	-50	1	5, 18, 21
	E-UTRA band 9, 18, 19	F_{DL_low}	–		F_{DL_high}	-50	1	5, 18
	Frequency range	470	–		694	-42	8	3, 22
	Frequency range	470	–		710	-26.2	6	23
	Frequency range	662	–		694	-26.2	6	3
	Frequency range	758	–		773	-32	1	3
	Frequency range	773	–		803	-50	1
	Frequency range	1884.5	–		1915.7	-41	0.3	4, 5, 18
CA_28A-42A	E-UTRA Band 1, 4, 32, 50, 51, 66, 65, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	E-UTRA Band 2, 3, 5, 7, 8, 18, 19, 20, 25, 26, 27, 31, 34, 38, 40, 41, 72, 73 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	5, 21
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	803	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 5
CA_39A-41C	E-UTRA Band 1, 8, 26, 28, 34, 40, 42, 44, 50, 51, 52, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1805		–	1855	-40	1	20
	Frequency range	1855		–	1880	-15.5	5	3, 13, 20
CA_40A-42A	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 11, 12, 13, 14, 17, 18, 19, 20, 21, 24, 25, 26, 27, 28, 29, 31, 32, 33, 34, 38, 39, 41, 44, 45, 50, 51, 65, 66, 67, 68, 69, 70, 72, 73, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	8
CA_41A-42A	E-UTRA Band 1, 3, 5, 8, 26, 28, 33, 34, 39, 40, 44, 45, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}		–	F_{DL_high}	-50	1	18
	NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5			1915.7	-41	0.3	4, 18
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. In case the exceptions are allowed due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3 or 4 for the 2^nd, 3^rd or 4^th harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3: These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the aggregated channel bandwidth. NOTE 4:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. NOTE 5:Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. NOTE 6: As exceptions, measurements with a level up to the applicable requirement of -36 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 3^rdharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 3^rd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 7: Void NOTE 8: Void NOTE 9: Void NOTE10: Void NOTE 11: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 12: This requirement is applicable for any channel bandwidths within the range 1920 – 1980 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE13: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. NOTE14:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE 15:Void NOTE 16:Void NOTE 17: This requirement is applicable only when Band 3 transmission frequency is less than or equal to 1765 MHz. NOTE 18: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz NOTE 19: Void NOTE 20: This requirement is only applicable for carriers with bandwidth confined within 1885-1920 MHz (requirement for carriers with at least 1RB confined within 1880 – 1885 MHz is not specified). This requirement applies for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1892.5 – 1894.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1895 – 1903 MHz. NOTE 21: As exceptions, measurements with a level up to the applicable requirement of -38 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 2^ndharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 2^nd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 22: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies. NOTE 23: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48. NOTE 24: Void NOTE 25: Void

Table 6.6.3.2A.0-1f: Requirements for dual-uplink inter-band carrier aggregation limits for Rel-17

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)				Maximum Level (dBm)	MBW (MHz)	NOTE
CA_1A-3A	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 38, 40, 41, 43, 44, 50, 51, 65, 67, 72, 73, 74, 75, 76 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 22, 42, 52 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
CA_1A-5A	E-UTRA Band 1, 5, 7, 8, 22, 28, 31, 38, 40, 42, 43, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3,34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 26	859		–	869	-27	1
	E-UTRA band 41, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_1A-7A	E-UTRA Band 1, 5, 7, 8, 20, 22, 26, 27, 28, 31,32, 40, 42, 43, 50, 51, 52, 65, 67, 72, 74, 75, 76 NR Band n78	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_1A-8A	E-UTRA Band 1, 20, 28, 31, 32, 38, 40, 50, 51, 65, 67, 72, 73, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 7, 22, 41, 42, 43, 52 NR Band n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 8, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	11
	Frequency range	860		–	890	-40	1	3, 11
	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
CA_1A-11A	E-UTRA Band 1, 3, 11, 18, 19, 21, 28, 34, 40, 42, 65 NR Band , n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_1A-18A	E-UTRA Band 1, 3, 11, 21, 40, 42, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	758		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
	Frequency range	860		–	890	-40	1
	Frequency range	945		–	960	-50	1
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_1A-19A	E-UTRA Band 1, 3, 11, 21, 28, 40, 42, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_1A-20A	E-UTRA Band 1, 3, 7, 8, 22, 31, 32, 34, 40, 43, 50, 51, 65, 67, 68, 72, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 38, 42, 69 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	758		–	788	-50	1
CA_1A-21A	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 42, 65 NR Band n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	945		–	960	-50	1
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_1A-26A	E-UTRA Band 1, 5, 7, 11, 18, 19, 21, 22, 26, 31, 38, 40, 42, 43, 50, 51, 65, 73, 74 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	1880		–	1895	-40	1	3, 12
	Frequency range	1895		–	1915	-15.5	5	3, 12, 13
	Frequency range	1915		–	1920	+1.6	5	3, 12, 13
	Frequency range	945		–	960	-50	1
	E-UTRA Band 41 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
CA_1A-28A	E-UTRA Band 3, 5, 7, 8, 18, 19, 20, 26, 27, 31, 38, 40, 41, 72, 73	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 22, 32, 42, 43, 50, 51, 52, 74, 75, 76 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	5, 21
	E-UTRA Band 1, 65	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	Frequency range	470		–	694	-42	8	3, 22
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	803	-50	1
	Frequency range	662		–	694	-26.2	6	3
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
CA_1A-41A	E-UTRA Band 1, 3, 5, 8, 26, 27, 28, 40, 42, 44, 45, 50, 51, 52, 65, 73, 74 NR Band n78	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	NR Band n77, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
	E-UTRA Band 11, 18, 19, 21	F_{DL_low}		–	F_{DL_high}	-50	1	30
CA_1A-42A	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 38, 40, 41, 44, 50, 51, 65, 67, 72, 73, 74, 75, 76 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	Frequency range	1880			1895	-40	1	3,12
	Frequency range	1895			1915	-15.5	5	3, 12, 13
	Frequency range	1915			1920	+1.6	5	3, 12, 13
CA_2A-4A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 27, 28, 29, 30, 41, 50, 51, 53, 66, 70, 71, 74, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 42, 43, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_2A-5A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 28, 29, 30, 42, 50, 51, 66, 70, 71, 74, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 26	859		–	869	-27	1
	E-UTRA Band 41, 43, 53 NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_2A-7A	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 26, 27, 29, 30, 42, 50, 51, 65, 66, 70, 74, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
CA_2A-7A	E-UTRA Band 43	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_2A-12A	E-UTRA Band 5, 13, 14, 17, 24, 26, 27, 30, 41, 50, 53, 71, 74, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 2, 12, 25, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 4, 51, 66, 70, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_2A-13A	E-UTRA Band 4, 5,12,13,17, 22, 26, 27, 29, 41, 42, 50, 51, 53, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 2,14, 25, 103	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 24, 30, 43, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	769		–	775	-35	0.00625	3
	Frequency range	799		–	805	-35	0.00625	3
CA_2A-14A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 27, 29, 30, 41, 48, 53, 66, 70, 71, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}		–	F_{DL_high}	-50	1	3
	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	769		–	775	-35	0.00625	3
	Frequency range	799		–	805	-35	0.00625	3, 9
CA_2A-48A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 50, 51, 53, 66, 70, 71, 74, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
CA_2A-49A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 25, 26, 29, 30, 41, 50, 51, 53, 66, 70, 71, 74, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
CA_3A-5A	E-UTRA Band 1, 5, 7, 8, 28, 31, 38, 40, 43, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3,34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 42, 52	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859		–	869	-27	1
CA_3A-7A	E-UTRA Band 1, 5, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 40, 43, 44, 50, 51, 65, 67, 72, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 22, 42, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_3A-8A	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40, 44, 50, 51, 65, 67, 72, 73, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 8	F_{DL_low}		–	F_{DL_high}	-50	1	2, 3
	E-UTRA band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	10,11
	E-UTRA band 7, 22, 41, 42, 43, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 10, 11
	Frequency range	860		–	890	-40	1	3,11,17
CA_3A-11A	E-UTRA Band 1, 18, 19, 28, 34, 40, 65	FDL_{_low}		–	FDL_{_high}	-50	1
	E-UTRA band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 42	FDL_{_low}		–	FDL_{_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_3A-18A	E-UTRA Band 1, 3, 11, 21, 28, 34, 40, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78,	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_3A-19A	E-UTRA Band 1, 11, 21, 28, 40, 65	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3, 34	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 42 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	3, 4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_3A-20A	E-UTRA Band 1, 7, 8, 31, 32, 33, 34, 40, 43, 50, 51, 65, 67, 72, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3, 20	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 38, 42, 52	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	758		–	788	-50	1
CA_3A-21A	E-UTRA Band 1, 18, 19, 28, 34, 40, 65 NR Band n79	FDL_{_low}		–	FDL_{_high}	-50	1
	E-UTRA band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 42 NR Band n77, n78,	FDL_{_low}		–	FDL_{_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_3A-26A	E-UTRA Band 1, 5, 7, 11, 18, 19, 21, 26, 34, 39, 40, 43, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA band 22, 41, 42 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
	Frequency range	945		–	960	-50	1
CA_3A-28A	E-UTRA Band 1, 11, 18, 19, 21, 22, 32, 42, 43, 50, 51, 52, 65, 74, 75, 76 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	E-UTRA band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 5, 7, 8, 20, 26, 27, 31, 34, 38, 40, 41, 72, 73	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	803	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 5
CA_3A-40A	E-UTRA Band 1, 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 28, 31, 32, 33, 34, 38, 39, 41, 43, 44. 45, 50, 51, 65, 67, 68, 69, 72, 73, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 42, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3
CA_3A-41A	E-UTRA Band 1, 5, 8, 26, 28, 33, 34, 39, 40, 44, 45, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 11, 18, 19, 21	F_{DL_low}		–	F_{DL_high}	-50	1	18
	NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5			1915.7	-41	0.3	4, 18
CA_3A-42A	E-UTRA Band 1, 5, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 40, 41, 44, 45, 50, 51, 65, 67, 72, 73, 74, 75, 76 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 11, 18, 19, 21	F_{DL_low}		–	F_{DL_high}	-50	1	13
	Frequency range	1884.5		–	1915.7	-41	0.3	4
CA_4A-5A	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 24, 25, 28, 29, 30, 43, 50, 51, 66, 70, 71, 74, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 26	859		–	869	-27	1
	E-UTRA band 41, 42, 53 NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_4A-7A	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 26, 27, 28, 29, 30, 43, 50, 51, 66, 74, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 42	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_4A-12A	E-UTRA Band 2, 5, 7,13, 14, 17, 24, 25, 26, 27, 30, 41, 43, 50, 53, 71, 74, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 4, 22, 42, 51, 66, 70, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_4A-13A	E-UTRA Band 2,4, 5, 7, 12,13,17,25, 26, 27, 29, 41, 43, 50, 51, 53, 66, 70, 71, 74, 85	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 14, 103	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 22, 24, 30, 42, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	769		–	775	-35	0.00625	3
	Frequency range	799		–	805	-35	0.00625	3
CA_4A-17A	E-UTRA Band 2, 5, 7,13, 14, 17, 24, 25, 26, 27, 30, 41, 43, 50, 53, 71, 74, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 4, 22, 42, 51, 66, 70, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 12, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_4A-28A	E-UTRA Band 2, 5, 7, 14, 24, 25, 26, 27, 30, 41, 53, 70, 71	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 4, 42, 43, 48, 50, 51, 66, 74	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	758			773	-32	1	3
	Frequency range	773			803	-50	1
CA_5A-7A	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 22, 28, 29, 30, 31, 40, 42, 43, 50, 51, 65, 66, 74, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 52 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859		–	869	-27	1
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_5A-12A	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 30, 31, 43, 50, 53, 71, 74, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 4, 22, 41, 42, 51, 66, 70, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859		–	869	-27	1
	E-UTRA band 12, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_5-17	E-UTRA Band 2, 5, 13, 14, 17, 24, 25, 30, 31, 43, 50, 71, 74, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 4, 22, 41, 42, 51, 53, 66, 70, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 26	859		–	869	-27	1
	E-UTRA band 12, 85	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_5A-40A	E-UTRA Band 1, 3, 5, 7, 8, 11, 18, 19, 21, 28, 31, 34, 38, 42, 43, 45, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 26	859		–	869	-27	1
	E-UTRA band 41, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	4
CA_7A-8A	E-UTRA Band 1, 20, 27, 28, 31, 32, 34, 40, 50, 51, 65, 67, 68, 72, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 7, 22, 42, 43, 52 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}		–	F_{DL_high}	-50	1	3
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_7A-20A	E-UTRA Band 1,3, 7, 8, 22, 28, 31, 32, 33, 34, 40, 43, 50, 51, 65, 67, 72, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 42, 52 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	2570		–	2575	+1.6	5	2, 3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	2, 3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_7A-26A	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 22, 29, 30, 31, 40, 42, 43, 65, 66, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	7
CA_7A-28A	E-UTRA Band 2, 3, 5, 7, 8, 20, 26, 27, 31, 34, 40, 72 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 1, 4, 22, 32, 42, 43, 50, 51, 52, 65, 66, 74, 75, 76 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	803	-50	1
	Frequency range	2570		–	2575	+1.6	5	3, 13, 14
	Frequency range	2575		–	2595	-15.5	5	3, 13, 14
	Frequency range	2595		–	2620	-40	1	3, 14
CA_8A-39A	E-UTRA Band 1, 28, 40, 45, 50, 51, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 22, 41, 42, 52 NR band n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}		–	F_{DL_high}	-50	1	3
CA_8A-41A	E-UTRA Band 1, 28, 34, 39, 40, 45, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA band 3, 42, 52 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	11
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 11
CA_11A-18A	E-UTRA Band 1, 3, 11, 21, 28, 34, 40, 42, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	860		–	890	-40	1	3
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
	Frequency range	945		–	960	-50	1
CA_11A-26A	E-UTRA Band 1, 3, 11, 18, 19, 21, 26, 28, 34, 40, 42, 65	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1	2
	Frequency range	2595		–	2645	-50	1
	Frequency range	945		–	960	-50	1
CA_13A-66A	E-UTRA Band 2, 4, 5, 12, 13, 17, 25, 26, 27, 29, 41, 50, 51, 53, 66, 70, 71, 74, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 14	F_{DL_low}		–	F_{DL_high}	-50	1	3
	E-UTRA Band 24, 30, 48, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	769		–	775	-35	0.00625	3
	Frequency range	799		–	805	-35	0.00625	3, 9
CA_14A-30A	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 27, 29, 30, 41, 48, 53, 66, 70, 71, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	769		–	775	-35	0.00625	3
	Frequency range	799		–	805	-35	0.00625	3, 9
CA_14A-66A	E-UTRA Band 2, 4, 5, 12, 13, 14, 17, 24, 25, 26, 27, 29, 30, 41, 53, 66, 70, 71, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 48, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	769		–	775	-35	0.00625	3
	Frequency range	799		–	805	-35	0.00625	3, 9
CA_18A-28A	E-UTRA Band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	5, 21
	E-UTRA Band 1, 65	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	E-UTRA Band 42, 43 NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 3, 34, 40	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	799	-50	1
	Frequency range	799		–	803	-40	1	3
	Frequency range	860		–	890	-40	1
	Frequency range	945		–	960	-50	1	3
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_19A-21A	E-UTRA Band 1, 3, 28, 34, 40, 42, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78,	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_19A-42A	E-UTRA Band 1, 3, 11, 21, 28, 34, 40, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_21A-28A	E-UTRA Band 1, 42, 65 NR Band n77, n78	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	E-UTRA Band 3, 18, 19, 34, 40 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	773		–	803	-50	1
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 5
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_21A-42A	E-UTRA Band 1, 3, 18, 19, 28, 34, 40, 65 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4
	Frequency range	2545		–	2575	-50	1
	Frequency range	2595		–	2645	-50	1
CA_25A-26A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 29, 30, 42, 48, 66, 70, 71, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
CA_25A-26A	E-UTRA Band 53 NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_25A-41A	E-UTRA Band 4, 5, 12, 13, 14, 17, 24, 26, 27, 28, 29, 30, 42, 45, 48, 66, 70, 71, 103	F_{DL_low}		–	F_{DL_high}	-50	1
CA_25A-41A	E-UTRA Band 2, 25, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	2
CA_26A-46A	E-UTRA Band 1, 2, 3, 4, 5, 11, 12, 13, 14, 17, 18,19, 21, 24, 25, 26, 29, 30, 31, 34, 39, 40, 42, 43, 48, 65, 66, 70, 71, 85, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 41, 53, NR Band n77	F_{DL_low}		–	F_{DL_high}	-50	1	1, 2
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	3
CA_26A-48A	E-UTRA Band 1, 2, 3, 4, 5, 11, 12, 13, 14, 17, 18,19, 21, 24, 25, 26, 29, 30, 31, 34, 39, 40, 50, 51, 65, 66, 70, 71, 73, 74, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 41	F_{DL_low}		–	F_{DL_high}	-50	1	1,2
	Frequency range	703		–	799	-50	1
	Frequency range	799		–	803	-40	1	2
	Frequency range	945		–	960	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	3
CA_28A-41A	E-UTRA Band E-UTRA Band 1, 4, 22, 32, 42, 45, 43, 48, 52, 65, 66 NR Band n77, n78, n79	F_{DL_low}	–		F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}	–		F_{DL_high}	-50	1	5, 6
	E-UTRA band 2, 3, 5, 8, 20, 25, 26, 27, 31, 33, 34, 40	F_{DL_low}	–		F_{DL_high}	-50	1
	E-UTRA band 11, 21	F_{DL_low}	–		F_{DL_high}	-50	1	5, 18, 21
	E-UTRA band 9, 18, 19	F_{DL_low}	–		F_{DL_high}	-50	1	5, 18
	Frequency range	470	–		694	-42	8	3, 22
	Frequency range	470	–		710	-26.2	6	23
	Frequency range	662	–		694	-26.2	6	3
	Frequency range	758	–		773	-32	1	3
	Frequency range	773	–		803	-50	1
	Frequency range	1884.5	–		1915.7	-41	0.3	4, 5, 18
CA_28A-42A	E-UTRA Band 1, 4, 32, 50, 51, 66, 65, 74, 75, 76	F_{DL_low}		–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}		–	F_{DL_high}	-50	1	5, 6
	E-UTRA Band 2, 3, 5, 7, 8, 18, 19, 20, 25, 26, 27, 31, 34, 38, 40, 41, 72, 73 NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 11, 21	F_{DL_low}		–	F_{DL_high}	-50	1	5, 21
	Frequency range	470		–	710	-26.2	6	23
	Frequency range	758		–	773	-32	1	3
	Frequency range	773		–	803	-50	1
	Frequency range	1884.5		–	1915.7	-41	0.3	4, 5
CA_39A-41C	E-UTRA Band 1, 8, 26, 28, 34, 40, 42, 44, 50, 51, 52, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n77, n78, n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1805		–	1855	-40	1	20
	Frequency range	1855		–	1880	-15.5	5	3, 13, 20
CA_40A-42A	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 11, 12, 13, 14, 17, 18, 19, 20, 21, 24, 25, 26, 27, 28, 29, 31, 32, 33, 34, 38, 39, 41, 44, 45, 50, 51, 65, 66, 67, 68, 69, 70, 72, 73, 74, 75, 76, 103	F_{DL_low}		–	F_{DL_high}	-50	1
	NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5		–	1915.7	-41	0.3	8
CA_41A-42A	E-UTRA Band 1, 3, 5, 8, 26, 28, 33, 34, 39, 40, 44, 45, 50, 51, 65, 73, 74	F_{DL_low}		–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}		–	F_{DL_high}	-50	1	18
	NR Band n79	F_{DL_low}		–	F_{DL_high}	-50	1	2
	Frequency range	1884.5			1915.7	-41	0.3	4, 18
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. In case the exceptions are allowed due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3 or 4 for the 2^nd, 3^rd or 4^th harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3: These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the aggregated channel bandwidth. NOTE 4:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. NOTE 5:Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. NOTE 6: As exceptions, measurements with a level up to the applicable requirement of -36 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 3^rdharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 3^rd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 7: Void NOTE 8: Void NOTE 9: Void NOTE10: Void NOTE 11: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 12: This requirement is applicable for any channel bandwidths within the range 1920 – 1980 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1927.5 – 1929.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1930 – 1938 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE13: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. NOTE14:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE 15:Void NOTE 16:Void NOTE 17: This requirement is applicable only when Band 3 transmission frequency is less than or equal to 1765 MHz. NOTE 18: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz NOTE 19: Void NOTE 20: This requirement is only applicable for carriers with bandwidth confined within 1885-1920 MHz (requirement for carriers with at least 1RB confined within 1880 – 1885 MHz is not specified). This requirement applies for an uplink transmission bandwidth less than or equal to 54 RB for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 1892.5 – 1894.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 1895 – 1903 MHz. NOTE 21: As exceptions, measurements with a level up to the applicable requirement of -38 dBm/MHz is permitted for each assigned E-UTRA carrier used in the measurement due to 2^ndharmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.6-1) for which the 2^nd harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 22: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies. NOTE 23: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48. NOTE 24: Void NOTE 25: Void

Table 6.6.3.2A.0-2a: Spurious emission band UE co-existence for intraband carrier aggregation limits for Rel10

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Note
CA_1C	E-UTRA Band 1, 7, 8, 11, 18, 19, 20, 21, 22, 38, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	8
CA_40C	E-UTRA Band 1, 3, 7, 8, 20, 22, 33, 34, 38, 39, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
NOTE1:F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.2-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1.3-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd , 3^rd , 4^th , [or 5^th ] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th [or 5^th ] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3:To meet these requirements some restriction will be needed for either the operating band or protected band NOTE 4:N/A NOTE 5:N/A NOTE 6:N/A NOTE 7:N/A NOTE 8:The requirement also applies for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.1.3-1 from the edge of the channel bandwidth. NOTE 9^:N/A.

Table 6.6.3.2A.0-2b: Spurious emission band UE co-existence for intraband carrier aggregation limits for Rel11

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Note
CA_1C	E-UTRA Band 1, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 38, 40, 41, 42, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	10

CA_7C	E-UTRA Band 1, 3, 7, 8, 20, 22, 27, 28, 29, 33, 34, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
CA_38C	E-UTRA Band 1,3, 8, 20, 22, 27, 28, 29, 33, 34, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
CA_40C	E-UTRA Band 1, 3, 7, 8, 20, 22, 26, 27, 33, 34, 38, 39, 41, 42, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1
CA_41C	E-UTRA Band 1, 2, 3, 4, 5, 8, 10, 12, 13 , 14, 17, 23, 24, 25, 26, 27, 28, 29, 34, 39, 40, 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
NOTE1:F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.2-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1.3-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd , 3^rd , 4^th [or 5^th ] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th or [5^th ] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3:To meet these requirements some restriction will be needed for either the operating band or protected band NOTE 4:N/A NOTE 5:N/A NOTE 6:N/A NOTE 7:N/A NOTE 8:N/A NOTE 9: N/A NOTE 10: The requirement also applies for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.1.3-1 from the edge of the aggregated channel bandwidth. NOTE 11: N/A NOTE 12: N/A

Table 6.6.3.2A.0-2c: Spurious emission band UE co-existence for intraband carrier aggregation limits for Rel12

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Note
CA_1C	E-UTRA Band 1, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 38, 40, 41, 42, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1C	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	10
CA_3C	E-UTRA Band 1, 7, 8, 20, 26, 27, 28, 31, 33, 34, 38, 41, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_7C	E-UTRA Band 1, 3, 7, 8, 20, 22, 27, 28, 29, 30, 31, 33, 34, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
CA_38C	E-UTRA Band 1,3, 8, 20, 22, 27, 28, 29, 30, 31, 33, 34, 40, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
CA_39C	E-UTRA Band 22, 34, 40, 41, 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
CA_40C	E-UTRA Band 1, 3, 7, 8, 20, 22, 26, 27, 33, 34, 38, 39, 41, 42, 43, 44	F_{DL_low}	–	F_{DL_high}	-50	1
CA_41C	E-UTRA Band 1, 2, 3, 4, 5, 8, 10, 12, 13 , 14, 17, 23, 24, 25, 26, 27, 28, 29, 30, 34, 39, 40, 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
CA_42C	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 11, 18, 19, 20, 21, 25, 26, 27, 28, 31, 33, 34, 38, 40, 41, 44	F_{DL_low}	–	F_{DL_high}	-50	1
CA_42C	Frequency range	1884.5	–	1915.7	-41	0.3
NOTE1:FDL_low and FDL_high refer to each E-UTRA frequency band specified in Table 5.2-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1.3-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th [or 5^th] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval NOTE 3:To meet these requirements some restriction will be needed for either the operating band or protected band NOTE 4:N/A NOTE 5:N/A NOTE 6:N/A NOTE 7:N/A NOTE 8:N/A NOTE 9: N/A NOTE 10: The requirement also applies for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.0-1 from the edge of the aggregated channel bandwidth. NOTE 11: N/A NOTE 12: N/A NOTE 13: N/A NOTE 14: N/A

Table 6.6.3.2A.0-2d: Spurious emission band UE co-existence for intraband carrier aggregation limits for Rel13

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
CA_1C	E-UTRA Band 1, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 38, 40, 41, 42, 43, 44, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1C	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	10
CA_3C	E-UTRA Band 1, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 41, 43, 44, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_7C	E-UTRA Band 1, 3, 7, 8, 20, 22, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_8B	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA band 7	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA Band 22, 41, 42, 43	F_{DL_low}		F_{DL_high}	-50	1	2
CA_38C	E-UTRA Band 1,3, 8, 20, 22, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_39C	E-UTRA Band 22, 34, 40, 41, 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
CA_40C	E-UTRA Band 1, 3, 7, 8, 20, 22, 26, 27, 32, 33, 34, 38, 39, 41, 42, 43, 44, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_41C	E-UTRA Band 1, 2, 3, 4, 5, 8, 10, 12, 13 , 14, 17, 23, 24, 25, 26, 27, 28, 29, 30, 34, 39, 40, 42, 44, 65, 66	F_{DL_low}	–	F_{DL_high}	-50	1
CA_42C	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 11, 18, 19, 20, 21, 25, 26, 27, 28, 31, 32, 33, 34, 38, 40, 41, 44, 65, 66, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_42C	Frequency range	1884.5	–	1915.7	-41	0.3
NOTE1:FDL_low and FDL_high refer to each E-UTRA frequency band specified in Table 5.5-1. NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th [or 5^th] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3:To meet these requirements some restriction will be needed for either the operating band or protected band. NOTE 4:N/A NOTE 5:N/A NOTE 6:N/A NOTE 7:N/A NOTE 8:N/A NOTE 9: N/A NOTE 10: The requirement also applies for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the aggregated channel bandwidth. NOTE 11: N/A NOTE 12: N/A NOTE 13: N/A NOTE 14: N/A

Table 6.6.3.2A.0-2e: Spurious emission band UE co-existence for intraband carrier aggregation limits for Rel14

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
CA_1C	E-UTRA Band 1, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 38, 40, 41, 42, 43, 44, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1C	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	10
CA_3C	E-UTRA Band 1, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 41, 43, 44, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_5B	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 12, 13, 14, 17, 24, 25, 28, 29, 30, 31, 34, 38, 40, 42, 43, 45, 48, 65, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
CA_7C	E-UTRA Band 1, 3, 7, 8, 20, 22, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_8B	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA band 7	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA Band 22, 41, 42, 43	F_{DL_low}		F_{DL_high}	-50	1	2
CA_38C	E-UTRA Band 1,3, 8, 20, 22, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_39C	E-UTRA Band 22, 34, 40, 41, 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
CA_40C	E-UTRA Band 1, 3, 7, 8, 20, 22, 26, 27, 32, 33, 34, 38, 39, 41, 42, 43, 44, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_40D	E-UTRA Band 1, 3, 7, 8, 20, 22, 26, 27, 32, 33, 34, 38, 39, 41, 42, 43, 44, 65, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_41C	E-UTRA Band 1, 2, 3, 4, 5, 8, 10, 12, 13 , 14, 17, 24, 25, 26, 27, 28, 29, 30, 34, 39, 40, 42, 44, 65, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
CA_42C	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 10, 11, 18, 19, 20, 21, 25, 26, 27, 28, 31, 32, 33, 34, 38, 40, 41, 44, 65, 66, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_42C	Frequency range	1884.5	–	1915.7	-41	0.3
NOTE1:FDL_low and FDL_high refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th [or 5^th] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval NOTE 3:To meet these requirements some restriction will be needed for either the operating band or protected band NOTE 4:N/A NOTE 5:N/A NOTE 6:N/A NOTE 7:N/A NOTE 8:N/A NOTE 9: N/A NOTE 10: The requirement also applies for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the aggregated channel bandwidth. NOTE 11: N/A NOTE 12: N/A NOTE 13: N/A NOTE 14: N/A

Table 6.6.3.2A.0-2f: Spurious emission band UE co-existence for intraband carrier aggregation limits for Rel15

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
CA_1C	E-UTRA Band 1, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 38, 40, 41, 42, 43, 44, 50, 51, 52, 65, 67, 72, 73, 74, 75, 76 NR Band n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	10
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_3C	E-UTRA Band 1, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 41, 43, 44, 50, 51, 65, 67, 72, 73, 74, 75, 76 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA Band 22, 42, 52 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_5B	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 24, 25, 28, 29, 30, 31, 34, 38, 40, 42, 43, 45, 48, 65, 66, 70, 71, 85	F_{DL_low}	–	F_{DL_high}	-50	1
CA_5B	E-UTRA band 52 NR Band n77, n78,n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_7C	E-UTRA Band 1, 3, 7, 8, 20, 22, 27, 28, 29, 30. 31, 32, 33, 34, 40, 42, 43, 50, 51, 52, 65, 67, 72, 74, 75, 76 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
CA_8B	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40, 50, 51, 72, 73, 74, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA band 7	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA Band 22, 41, 42, 43, 52 NR Band n77, n78,n79	F_{DL_low}		F_{DL_high}	-50	1	2
CA_38C	E-UTRA Band 1,3, 8, 20, 22, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 50, 51, 52, 65, 67, 72, 74, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1
CA_39C	E-UTRA Band 22, 34, 40, 41, 42, 44, 50, 51, 52, 73, 74 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
CA_39C	NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_40D	E-UTRA Band 1, 3, 7, 8, 20, 22, 26, 27, 31, 32, 33, 34, 38, 39, 41, 42, 43, 44, 50, 51, 52, 65, 67, 72, 73, 74, 75, 76 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
CA_40D	NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_41C	E-UTRA Band 1, 2, 3, 4, 5, 8, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 34, 39, 40, 42, 44, 50, 51, 52, 65, 66, 70, 71, 73, 74, 85 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
CA_41C	NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_42C	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 11, 18, 19, 20, 21, 25, 26, 27, 28, 31, 32, 33, 34, 38, 40, 41, 44, 50, 51, 65, 66, 67, 72, 73, 74, 75, 76 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
CA_42C	Frequency range	1884.5	–	1915.7	-41	0.3
CA_66C	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 38, 41, 43, 50, 51, 66, 70, 71, 74, 85	F_{DL_low}	–	F_{DL_high}	-50	1
CA_66C	E-UTRA Band 42, 48	F_{DL_low}	–	F_{DL_high}	-50	1	2
NOTE1:FDL_low and FDL_high refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th [or 5^th] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval NOTE 3:To meet these requirements some restriction will be needed for either the operating band or protected band NOTE 4:N/A NOTE 5:N/A NOTE 6:N/A NOTE 7:N/A NOTE 8:N/A NOTE 9: N/A NOTE 10: The requirement also applies for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the aggregated channel bandwidth. NOTE 11: N/A NOTE 12: N/A NOTE 13: N/A NOTE 14: N/A

Table 6.6.3.2A.0-2h: Spurious emission band UE co-existence for intraband carrier aggregation limits for Rel17

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
CA_1C	E-UTRA Band 1, 7, 8, 11, 18, 19, 20, 21, 22, 26, 27, 28, 31, 32, 38, 40, 41, 42, 43, 44, 50, 51, 52, 65, 67, 72, 73, 74, 75, 76 NR Band n78, n79	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	10
	NR Band n77	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_3C	E-UTRA Band 1, 7, 8, 20, 26, 27, 28, 31, 32, 33, 34, 38, 41, 43, 44, 50, 51, 65, 67, 72, 73, 74, 75, 76 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA Band 22, 42, 52 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_5B	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 24, 25, 28, 29, 30, 31, 34, 38, 40, 42, 43, 45, 48, 65, 66, 70, 71, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
CA_5B	E-UTRA band 52 NR Band n77, n78,n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_7C	E-UTRA Band 1, 3, 7, 8, 20, 22, 27, 28, 29, 30. 31, 32, 33, 34, 40, 42, 43, 50, 51, 52, 65, 67, 72, 74, 75, 76 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
CA_8B	E-UTRA Band 1, 20, 28, 31, 32, 33, 34, 38, 39, 40, 50, 51, 72, 73, 74, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA band 7	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 8	F_{DL_low}	–	F_{DL_high}	-50	1	10
	E-UTRA Band 22, 41, 42, 43, 52 NR Band n77, n78,n79	F_{DL_low}		F_{DL_high}	-50	1	2
CA_38C	E-UTRA Band 1,3, 8, 20, 22, 27, 28, 29, 30, 31, 32, 33, 34, 40, 42, 43, 50, 51, 52, 65, 67, 72, 74, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1
CA_39C	E-UTRA Band 22, 34, 40, 41, 42, 44, 50, 51, 52, 73, 74 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
CA_39C	NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_40D	E-UTRA Band 1, 3, 7, 8, 20, 22, 26, 27, 31, 32, 33, 34, 38, 39, 41, 42, 43, 44, 50, 51, 52, 65, 67, 72, 73, 74, 75, 76 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
CA_40D	NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_41C	E-UTRA Band 1, 2, 3, 4, 5, 8, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 34, 39, 40, 42, 44, 50, 51, 52, 65, 66, 70, 71, 73, 74, 85, 103 NR Band n77, n78	F_{DL_low}	–	F_{DL_high}	-50	1
CA_41C	NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_42C	E-UTRA Band 1, 2, 3, 4, 5, 7, 8, 11, 18, 19, 20, 21, 25, 26, 27, 28, 31, 32, 33, 34, 38, 40, 41, 44, 50, 51, 65, 66, 67, 72, 73, 74, 75, 76 NR Band n79	F_{DL_low}	–	F_{DL_high}	-50	1
CA_42C	Frequency range	1884.5	–	1915.7	-41	0.3
CA_66C	E-UTRA Band 2, 4, 5, 7, 12, 13, 14, 17, 24, 25, 26, 27, 28, 29, 30, 38, 41, 43, 50, 51, 66, 70, 71, 74, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
CA_66C	E-UTRA Band 42, 48	F_{DL_low}	–	F_{DL_high}	-50	1	2
NOTE1:FDL_low and FDL_high refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. Due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3, 4, [5] for the 2^nd, 3^rd, 4^th [or 5^th] harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval NOTE 3:To meet these requirements some restriction will be needed for either the operating band or protected band NOTE 4:N/A NOTE 5:N/A NOTE 6:N/A NOTE 7:N/A NOTE 8:N/A NOTE 9: N/A NOTE 10: The requirement also applies for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the aggregated channel bandwidth. NOTE 11: N/A NOTE 12: N/A NOTE 13: N/A NOTE 14: N/A

Table 6.6.3.2A.0-3: Requirements for intraband non-contiguous CA

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Note
CA_4A-4A	E-UTRA Band 2, 4, 5, 7, 10, 12, 13, 14, 17, 22, 23, 24, 25, 26, 27, 28, 29, 30, 41, 43, 53, 66, 71, 85, 103	F_{DL_low}	–	F_{DL_high}	-50	1
CA_4A-4A	E-UTRA Band 22, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
NOTE1:F_{DL_low}and F_{DL_high}refer to each E-UTRA frequency band specified in Table 5.2-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1.3-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2nd or 3rd harmonic spurious emissions. An exception is allowed if there is at least one individual RE within the transmission bandwidth (see Figure 5.4.2-1) for which the 2nd or 3rd harmonic, i.e. the frequency equal to two or three times the frequency of that RE, is within the measurement bandwidth (MBW).

The normative reference for this requirement is TS 36.101 [2] subclause 6.6.3.2A.

This test use minimum requirements from many releases of TS 36.101 [2] due to release independence defined in TS 36.307 [16].

6.6.3.2A.1 Spurious emission band UE co-existence for CA (intra-band contiguous DL CA and UL CA)

Editor’s Note : Additional TP analysis needs to be added to TR36.905

6.6.3.2A.1.1 Test purpose

To verify that UE transmitter does not cause unacceptable interference to co-existing systems for the specified bands which has specific requirements in terms of transmitter spurious emissions for intra-band contiguous DL CA and UL CA.

6.6.3.2A.1.2 Test applicability

This test case applies to all types of E-UTRA UE release 10 and forward that support intra-band contiguous DL CA and UL CA.

6.6.3.2A.1.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.2A.0.

6.6.3.2A.1.4 Test description

6.6.3.2A.1.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and channel bandwidths based on E-UTRA bands specified in Table 5.4.2.1-1. All of these configurations shall be tested with applicable test parameters for each channel bandwidth, and are shown in Table 6.6.3.2A.1.4.1-1. The details of the uplink reference measurement channels (RMCs) are specified in Annexe A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.2A.1.4.1-1: Test Configuration Table

Initial Conditions
Test Environment as specified in TS 36.508[7] clause 4.1				NC
Test Frequencies as specified in TS36.508 [7] clause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.				Low range, High range
Test CC Combination setting (NRB_agg) as specified in clause 5.4.2A.1 for the CA Configuration				Lowest N_{RB_agg}Highest N_{RB_agg} (Note 2)
Test Parameters for CA Configurations
CA Configuration / N_{RB_agg}		DL Allocation	CC MOD	UL Allocation
PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}	PCC & SCC RB allocations (L_CRB @ RB_start)
25	50	N/A	QPSK	2	P_1@0	S_1@49
25	50		QPSK	75	P_25@0	S_50@0
50	25		QPSK	2	P_1@0	S_1@24
50	25		QPSK	75	P_50@0	S_25@0
50	50		QPSK	2	P_1@0	S_1@49
50	50		QPSK	100	P_50@0	S_50@0
75	75		QPSK	2	P_1@0	S_1@74
75	75		QPSK	150	P_75@0	S_75@0
100	25		QPSK	2	P_1@0	S_1@24
100	25		QPSK	125	P_100@0	S_25@0
100	50		QPSK	2	P_1@0	S_1@49
100	50		QPSK	150	P_100@0	S_50@0
100	75		QPSK	2	P_1@0	S_1@74
100	75		QPSK	175	P_100@0	S_75@0
100	100		QPSK	2	P_1@0	S_1@99
100	100		QPSK	200	P_100@0	S_100@0
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration, which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1. Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same N_{RB_agg}, only the combination with the highest NRB_PCC is tested.

1. Connect the SS to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure group A.33 as appropriate.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals for PCC are initially set up according to Annex C.0, C.1 and Annex C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Table 6.6.3.2A.1.4.1-1.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.2A.1.4.3.

6.6.3.2A.1.4.2 Test procedure

1. Configure SCC according to Annex C.0, C.1 and Annex C.3.0 for all downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4. Message contents are defined in clause 6.6.3.2A.1.4.3

3. SS activates SCC by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 6.6.3.2A.1.4.1-1 on both PCC and SCC. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

5. Send continuously uplink power control “up” commands in every uplink scheduling information to the UE until the UE transmits at P_UMAX level.

6. Measure the power of the transmitted signal with a measurement filter of bandwidths according to Table 6.6.3.2A.0-2a to 6.6.3.2A.0-2f. The centre frequency of the filter shall be stepped in contiguous steps according to Table 6.6.3.2A.0-2a to 6.6.3.2A.0-2f. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

6.6.3.2A.1.4.3 Message contents

Message contents are according to TS 36.508 [7] subclause 4.6.

6.6.3.2A.1.5 Test requirement

Test requirements for Spurious Emissions UE Co-existence are the same as the minimum requirements and are not repeated in this section.

The measured average power of spurious emission, derived in step 6, shall not exceed the described value in Tables 6.6.3.2A.1.5-1.

The requirements for the UE are release specific and can be found in Tables 6.6.3.2A.0-2a to 6.6.3.2A.0-2f. If the UE support a band, which is not defined in the table corresponding UE’s release, the requirements for this band are taken from the table of earliest release where requirements for this band are defined. This has been described in following Table 6.6.3.2A.1.5-1.

Table 6.6.3.2A.1.5-1: UE Requirements according to UE E-UTRA release and supported E-UTRA CA configuration

E-UTRA CA Configuration		UE Requirements per release
	Rel-10		Rel-11	Rel-12	Rel-13	Rel-14	Rel-15
CA_1C	Table 6.6.3.2A.0-2a		Table 6.6.3.2A.0-2b	Table 6.6.3.2A.0-2c	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2f
CA_3C	Table 6.6.3.2A.0-2c		Table 6.6.3.2A.0-2c	Table 6.6.3.2A.0-2c	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2f
CA_7C	Table 6.6.3.2A.0-2b		Table 6.6.3.2A.0-2b	Table 6.6.3.2A.0-2c	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2f
CA_8B	Table 6.6.3.2A.0-2d		Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2f
CA_38C	Table 6.6.3.2A.0-2b		Table 6.6.3.2A.0-2b	Table 6.6.3.2A.0-2c	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2f
CA_39C	Table 6.6.3.2A.0-2c		Table 6.6.3.2A.0-2c	Table 6.6.3.2A.0-2c	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2f
CA_40C	Table 6.6.3.2A.0-2a		Table 6.6.3.2A.0-2b	Table 6.6.3.2A.0-2c	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2f
CA_41C	Table 6.6.3.2A.0-2b		Table 6.6.3.2A.0-2b	Table 6.6.3.2A.0-2c	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2e	Table 6.6.3.2A.0-2f
CA_42C	Table 6.6.3.2A.0-2c		Table 6.6.3.2A.0-2c	Table 6.6.3.2A.0-2c	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2d	Table 6.6.3.2A.0-2f

6.6.3.2A.2 Spurious emission band UE co-existence for CA (inter-band DL CA and UL CA)

6.6.3.2A.2.1 Test purpose

6.6.3.2A.2.2 Test applicability

This test case applies to all types of E-UTRA UE release 11 and forward that support inter-band DL CA and UL CA.

6.6.3.2A.2.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.2A.0.

6.6.3.2A.2.4 Test description

6.6.3.2A.2.4.1 Initial conditions

Same as in clause 6.6.3.2A.1.4.1 with the following exceptions:

– Instead of Table 5.4.2A.1-1🡪 use Table 5.4.2A.1-2 for CA configurations with two bands or Table 5.4.2A.1-2a for CA configurations with three bands.

– Instead of Table 6.6.3.2A.1.4.1-1 🡪 use Table 6.6.3.2A.2.4.1-1.

– Instead of clause 6.6.3.2A.1.4.3 use clause 6.6.3.2A.2.4.3.

Table 6.6.3.2A.2.4.1-1: Test Configuration Table

Initial Conditions

Test Environment as specified in TS 36.508[7] subclause 4.1

Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes.

For test frequencies refer to “Range” columns.

Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.

Refer to “PCC N_RB”and “SCC N_RB” columns

Test Parameters for CA Configurations

CA Configuration / N_{RB_agg} (Note 4)

DL Allocation

UL Allocation (Note 2,3)

CA Configuration

PCC N_RB

SCC N_RB

CC MOD

PCC & SCC
RB allocation

CC MOD

PCC & SCC RB allocations
(L_CRB @ RB_start)

PCC

SCC

PCC

SCC

Band

Range

Band

Range

Default Test Settings for a CA_XA-YA Configuration

Low

Highest N_RB

QPSK

1@0

High

Highest N_RB

QPSK

1@RB_max

Test Settings for CA_1A-3A Configuration

Low

100

QPSK

1@0

Low

100

QPSK

1@99

1@0

High

100

QPSK

1@99

High

Note 7

100

QPSK

1@99

1@0

Test Settings for CA_1A-7A Configuration(Note 12)

High

Low

100

QPSK

1@99

1@0

High

Low

100

QPSK

1@49

Test Settings for CA_1A-8A Configuration

Low

QPSK

1@0

Low

100

QPSK

1@0

Test Settings for CA_1A-18A Configuration

Low

100

QPSK

1@0

Low

100

QPSK

1@99

1@74

Test Settings for CA_1A-19A Configuration

Mid

QPSK

1@0

Mid

QPSK

25@0

Mid

100

QPSK

1@0

Mid

100

QPSK

100@0

75@0

Test Settings for CA_1A-21A Configuration

Mid

QPSK

1@24

Mid

QPSK

1@24

1@12

Mid

QPSK

25@0

Mid

100

QPSK

1@99

1@74

Mid

100

QPSK

1@99

1@37

Mid

100

QPSK

100@0

75@0

Test Settings for CA_1A-28A Configuration (Note 16)

Low

Mid

100

QPSK

1@0

1@49

Low

100

QPSK

1@0

High

Mid

100

QPSK

1@99

1@47

Low

Mid

QPSK

1@0

1@49

Low

QPSK

1@0

High

Mid

QPSK

1@49

1@47

Test Settings for CA_1A-42A Configuration (Note 13)

Low

100

QPSK

1@0

Low

100

QPSK

1@0

1@99

High

Mid

100

QPSK

1@99

1@24

High

Low

100

QPSK

1@49

1@0

Test Settings for CA_2A-4A Configuration (Note 6)

Low

QPSK

1@0

High

QPSK

1@49

Low

QPSK

1@49

High

Low

QPSK

1@49

1@0

High

Low

QPSK

1@49

Low

100

QPSK

1@0

High

100

QPSK

1@99

Low

100

QPSK

1@99

High

Low

100

QPSK

1@99

1@0

High

Low

100

QPSK

1@99

Test Settings for CA_2A-7A Configuration

Low

High

100

QPSK

1@0

1@99

Test Settings for CA_3A-5A Configuration

Low

QPSK

1@0

High

QPSK

1@49

Low

High

QPSK

1@0

1@49

Low

100

QPSK

1@0

High

100

QPSK

1@99

1@49

Low

High

100

QPSK

1@0

1@49

Test Settings for CA_3A-7A Configuration (Note 5)

Low

100

QPSK

1@0

High

100

QPSK

1@99

Low

100

QPSK

1@75

1@99

High

100

QPSK

1@0

1@99

Low

High

100

QPSK

1@0

1@99

Low

High

100

QPSK

1@99

High

Low

100

QPSK

1@0

1@99

Test Settings for CA_3A-8A Configuration

Low

QPSK

1@0

High

QPSK

1@49

High

QPSK

1@0

Low

High

QPSK

1@0

1@49

Low

100

QPSK

1@0

High

100

QPSK

1@99

1@49

Low

100

QPSK

1@99

1@49

High

100

QPSK

1@0

Low

High

100

QPSK

1@0

1@49

Test Settings for CA_3A-18A Configuration

Low

100

QPSK

1@0

Low

100

QPSK

1@99

1@74

Test Settings for CA_3A-19A Configuration

High

Mid

QPSK

1@0

High

Mid

QPSK

1@24

1@0

High

Mid

QPSK

25@0

High

Mid

100

QPSK

1@0

High

Mid

100

QPSK

1@99

1@0

High

Mid

100

QPSK

100@0

75@0

Test Settings for CA_3A-20A Configuration

Low

100

QPSK

1@0

High

100

QPSK

1@99

1@49

High

100

QPSK

1@99

1@0

Low

100

QPSK

1@0

High

100

QPSK

1@99

High

100

QPSK

1@99

1@0

Test Settings for CA_3A-26A Configuration

Low

QPSK

1@0

High

QPSK

1@49

Low

QPSK

1@0

1@49

High

QPSK

1@49

1@0

Low

100

QPSK

1@0

High

100

QPSK

1@99

1@74

Low

100

QPSK

1@0

1@74

High

100

QPSK

1@99

1@0

Test Settings for CA_3A-28A Configuration

High

100

QPSK

1@99

1@49

Low

100

QPSK

1@0

1@49

Test Settings for CA_3A-41A Configuration

Low

100

QPSK

1@0

Low

100

QPSK

1@99

Mid

High

100

QPSK

1@49

Mid

100

QPSK

1@0

1@99

Low

High

100

QPSK

1@49

1@99

Test Settings for CA_4A-5A Configuration

Low

QPSK

1@0

High

QPSK

1@49

Low

High

QPSK

1@0

1@49

Low

100

QPSK

1@0

High

100

QPSK

1@99

1@49

Low

High

100

QPSK

1@0

1@49

Test Settings for CA_4A-7A Configuration

Low

100

QPSK

1@0

High

Low

100

QPSK

1@0

High

Low

100

QPSK

1@49

1@0

High

Low

100

QPSK

1@49

1@99

Low

High

100

QPSK

1@49

1@0

Low

High

100

QPSK

1@0

1@99

Low

100

QPSK

1@0

High

Low

100

QPSK

1@99

1@0

High

Low

100

QPSK

1@99

High

Low

100

QPSK

1@99

1@49

Low

High

100

QPSK

1@99

Low

High

100

QPSK

1@0

1@99

Test Settings for CA_5A-7A Configuration

High

100

QPSK

1@49

1@99

High

100

QPSK

1@24

1@0

High

Low

100

QPSK

1@49

1@0

Test Settings for CA_5A-12A Configuration

Low

QPSK

1@0

1@49

High

QPSK

1@0

Test Settings for CA_5A-17A Configuration

Low

QPSK

1@0

Test Settings for CA_7A-20A Configuration

High

100

QPSK

1@99

1@49

Low

100

QPSK

1@0

1@49

Low

High

100

QPSK

1@0

1@49

High

100

QPSK

1@99

Low

100

QPSK

1@0

1@99

Test Settings for CA_7A-28A Configuration

High

100

QPSK

1@0

1@74

High

100

QPSK

1@99

Test Settings for CA_18A-28A Configuration

Low

Note 15

QPSK

1@0

1@2

Low

Note 15

QPSK

1@74

1@47

Test Settings for CA_39A-41A Configuration

High

100

QPSK

1@99

Test Settings for CA_41A-42A Configuration (Note 14)

Note 8

Low

100

QPSK

1@0

1@99

Note 9

Note 11

100

QPSK

1@22

1@99

Note 9

Low

100

QPSK

1@44

1@99

Note 8

Low

100

QPSK

1@99

Note 9

High

100

QPSK

1@0

1@99

Note 9

High

100

QPSK

1@44

1@99

Note 10

Low

100

QPSK

1@0

1@99

Note 8

Low

100

QPSK

1@99

1@0

Note 9

Mid

100

QPSK

1@99

Low

High

100

QPSK

1@99

Note 1: CA Configuration Test CC Combination test settings are checked separately for each CA Configuration.

Note 2: Use CA Configuration – specific test points if present in the table. Otherwise use the Default Test Settings test points.

Note 3: X,Y correspond to the different bands in the CA Configuration. E.g. for CA_1A-19A,X=1,Y=19.

Note 4: For CA configurations CA_1A-18A, CA_1A-19A, CA_1A-21A , CA_3A-19A , CA_3A-28A and CA_18A-28A each test point shall be tested. For all other CA configurations only test points with highest N_{RB_agg}, according to UE supported BCS shall be tested.

Note 5: Test Point ID 7 for CA_3A-7A is applicable only for a Rel-13 and forward UE.

Note 6: Test Point ID 3 and Test Point ID 8 for CA_2A-4A are applicable only for a Rel-14 and forward UE.

Note 7: Test Point ID 4 for CA_1A-3A has the centre carrier frequency 1849.9 MHz, i.e. DL E-ARFCN is 1649.

Note 8: Test Point ID 1, 4 and 8 for CA_41A-42A have the centre carrier frequency of 2635 MHz in Band 41 (EARFCN=41040).

Note 9: Test Point ID 2, 3, 5, 6 and 9 for CA_41A-42A has the centre carrier frequency of 2555 MHz in Band 41 (EARFCN=40240).

Note 10: Test Point ID 7 for CA_41A-42A has the centre carrier frequency of 2674 MHz in Band 41 (EARFCN=41430).

Note 11: Test Point ID 2 for CA_41A-42A has the centre carrier frequency of 3421 MHz in Band 42 (EARFCN=41800).

Note 12: Test Point ID 2 for CA_1A-7A is applicable only for a Rel-15 and forward UE.

Note 13: Test Point ID 4 for CA_1A-42A is applicable only for a Rel-15 and forward UE.

Note 14: Test Point ID 10 for CA_41A-42A is applicable only for a Rel-15 and forward UE.

Note 15: Test Point ID 1 and 2 for CA_18A-28A have the centre carrier frequency of 778 MHz in Band 28 (EARFCN=9410).

Note 16: As an exception to Note 4, Test Point ID 3 for CA_1A-28A shall be tested for a UE supporting bandwidth combination set 0, even though it has not highest N_{RB_agg}for this UE.

6.6.3.2A.2.4.2 Test procedure

1. Configure SCC according to Annex C.0, C.1 and Annex C.3.0 for all downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4. Message contents are defined in clause 6.6.3.2A.2.4.3

3. SS activates SCC by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 6.6.3.2A.2.4.1-1 on both PCC and SCC. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

5. Send continuously uplink power control “up” commands in every uplink scheduling information to the UE until the UE transmits at P_UMAX level.

6. Measure the power of the transmitted signal with a measurement filter of bandwidths according to Table 6.6.3.2A.2.5-1 to Table 6.6.3.2A.2.5-4. The centre frequency of the filter shall be stepped in contiguous steps according to Table 6.6.3.2A.2.5-1 to Table 6.6.3.2A.2.5-4. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

6.6.3.2A.2.4.3 Message contents

Message contents are according to TS 36.508 [7] clause 4.6. In test procedure step 2, for SCC configuration there are no additional message contents.

6.6.3.2A.2.5 Test requirement

The measured average power of spurious emission, derived in step 6, shall not exceed the described value in Tables 6.6.3.2A.2.5-1 to 6.6.3.2A.2.5-4 according to the following rule:

The requirements for the UE are release specific and can be found in Tables 6.6.3.2A.2.5-1 to 6.6.3.2A.2.5-5. If the UE supports a CA configuration, which is not defined in the table corresponding to UE’s release, the requirements for this CA configuration are taken from the table of earliest release where requirements for this CA Configuration are defined. This has been described in following Table 6.6.3.2A.2.5-0.

Table 6.6.3.2A.2.5-0: UE Requirements according to UE E-UTRA release and supported E-UTRA CA Configuration

E-UTRA CA Configuration	UE Requirements per release
E-UTRA CA Configuration	Rel-11	Rel-12	Rel-13	Rel-14	Rel-15
CA_1A-3A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_1A-5A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_1A-7A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_1A-8A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_1A-18A	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_1A-19A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_1A-21A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_1A-26A	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_1A-28A	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_1A-42A	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_2A-4A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_2A-5A	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_2A-7A	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_2A-12A	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_2A-13A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.25-3	Table 6.6.3.2A.25-4
CA_3A-5A	Table 6.6.3.2A.25-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.25-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_3A-7A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_3A-8A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_3A-18A	Table 6.6.3.2A.2.5-4	Table 6.6.3.2A.2.5-4	Table 6.6.3.2A.2.5-4	Table 6.6.3.2A.2.5-4	Table 6.6.3.2A.2.5-4
CA_3A-19A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_3A-20A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_3A-21A	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3
CA_3A-26A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_3A-28A	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_3A-42A	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3
CA_4A-5A	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_4A-7A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_4A-12A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_4A-13A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_4A-17A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_5A-7A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_5A-12A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_5A-17A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_7A-20A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_7A-28A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_8A-41A	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3
CA_11A-18A	6.6.3.2A.2.5-4	6.6.3.2A.2.5-4	6.6.3.2A.2.5-4	6.6.3.2A.2.5-4	6.6.3.2A.2.5-4
CA_18A-28A	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA_19A-21A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA 19A-42A	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3
CA 21A-42A	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3
CA 39A-41A	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-1	Table 6.6.3.2A.2.5-2	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-4
CA 41A-42A	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3	Table 6.6.3.2A.2.5-3

Table 6.6.3.2A.2.5-1: Requirements for dual-uplink inter-band carrier aggregation for Rel-11 and Rel-12

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Note
CA_1A-3A	E-UTRA Band 1, 32, 43	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-3A	E-UTRA band 21	F_{DL_low}	–	F_{DL_high}	-50	1	10
CA_1A-5A	E-UTRA Band 22, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-7A	E-UTRA Band 32	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-8A	E-UTRA band43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_1A-19A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-21A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-21A	Frequency range	945	–	960	-50	1
CA_2A-4A	E-UTRA Band 4, 10, 22, 24	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-13A	E-UTRA Band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-5A	E-UTRA Band 5, 7, 8, 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-5A	E-UTRA band 26	859	–	869	-27	1
CA_3A-7A	E-UTRA Band 5,8, 20, 26, 27, 28, 44	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-7A	E-UTRA band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_3A-8A	E-UTRA Band 20, 28, 38, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 7, 22, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	860	–	890	-40	1	3,11,17
CA_3A-19A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
	Frequency range	2595	–	2645	-50	1
CA_3A-20A	E-UTRA Band 7, 8	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-20A	E-UTRA Band 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_3A-26A	E-UTRA Band 5, 7, 26	F_{DL_low}	–	F_{DL_high}	-50	1

	E-UTRA band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
CA_4A-7A	E-UTRA Band 5, 12, 13, 14, 17, 26, 27, 28	F_{DL_low}	–	F_{DL_high}	-50	1
CA_4A-7A	E-UTRA band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_4A-12A	No requirement
CA_4A-13A	E-UTRA Band 7, 41	F_{DL_low}	–	F_{DL_high}	-50	1
CA_4A-17A	No requirement
CA_5A-7A	E-UTRA Band 5, 28, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_5A-7A	E-UTRA band 26	859	–	869	-27	1
CA_5A-12A	E-UTRA Band 24, 30	F_{DL_low}	–	F_{DL_high}	-50	1
CA_5A-17A	E-UTRA Band 24, 30	F_{DL_low}	–	F_{DL_high}	-50	1
CA_7A-20A	E-UTRA Band 28	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_7A-28A	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1
CA_19A-21A	No requirement
CA_39A-41A	E-UTRA Band 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.2-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1.3-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.4.2-1) for which the 2^nd, 3^rd or 4^th harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 3: These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.0-1 from the edge of the aggregated channel bandwidth. NOTE 4-9:Void. NOTE10: This requirement applies for 5, 10, 15 and 20 MHz E-UTRA channel bandwidth allocated within 1744.9MHz and 1784.9MHz. NOTE 11: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 12: Void. NOTE13: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. NOTE14:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE 15:Void. NOTE 16:Void. NOTE 17: This requirement is applicable only when Band 3 transmission frequency is less than or equal to 1765 MHz. NOTE 18-20: Void.

Table 6.6.3.2A.2.5-2: Requirements for dual-uplink inter-band carrier aggregation for Rel-13

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Note
CA_1A-3A	E-UTRA Band 1, 32, 43, 65	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-3A	E-UTRA band 21	F_{DL_low}	–	F_{DL_high}	-50	1	10
CA_1A-5A	E-UTRA Band 22, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-7A	E-UTRA Band 32	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-8A	E-UTRA band43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_1A-18A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-19A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-21A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-21A	Frequency range	945	–	960	-50	1
CA_1A-26A	E-UTRA Band 22, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-28A	E-UTRA Band 7, 31, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	470	–	694	-42	8	3, 22
	Frequency range	470	–	710	-26.2	6	23
CA_1A-42A	E-UTRA Band 11, 21, 31, 32	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-4A	E-UTRA Band 4, 10, 22, 24, 66	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-5A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-5A	E-UTRA Band 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-12A	E-UTRA Band 41	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-13A	E-UTRA Band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-5A	E-UTRA Band 5, 7, 8, 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-5A	E-UTRA band 26	859	–	869	-27	1
CA_3A-7A	E-UTRA Band 5, 8, 20, 26, 27, 28, 44, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-7A	E-UTRA band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_3A-8A	E-UTRA Band 20, 28, 38, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 7, 22, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	860	–	890	-40	1	3,11,17
CA_3A-19A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
	Frequency range	2595	–	2645	-50	1
CA_3A-20A	E-UTRA Band 7, 8	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-20A	E-UTRA Band 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_3A-26A	E-UTRA Band 5, 7, 26	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
CA_4A-5A	E-UTRA Band 5,7	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 26	859	–	869	-27	1
	E-UTRA band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_4A-7A	E-UTRA Band 5, 12, 13, 14, 17, 26, 27, 28	F_{DL_low}	–	F_{DL_high}	-50	1
CA_4A-7A	E-UTRA band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_4A-12A	No requirement
CA_4A-13A	E-UTRA Band 7, 41	F_{DL_low}	–	F_{DL_high}	-50	1
CA_4A-17A	No requirement
CA_5A-7A	E-UTRA Band 5, 28, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_5A-7A	E-UTRA band 26	859	–	869	-27	1
CA_5A-12A	E-UTRA Band 24, 30	F_{DL_low}	–	F_{DL_high}	-50	1
CA_5A-17A	E-UTRA Band 24, 30	F_{DL_low}	–	F_{DL_high}	-50	1
CA_7A-20A	E-UTRA Band 28	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_7A-28A	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1
CA_18A-28A	Frequency range	470	–	710	-26.2	6	23
CA_19A-21A	No requirement
CA_39A-41A	E-UTRA Band 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.2-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1.3-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. An exception is allowed if there is at least one individual RB within the transmission bandwidth (see Figure 5.4.2-1) for which the 2^nd, 3^rd or 4^th harmonic totally or partially overlaps the measurement bandwidth (MBW). NOTE 3: These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.0-1 from the edge of the aggregated channel bandwidth. NOTE 4-9:Void. NOTE10: This requirement applies for 5, 10, 15 and 20 MHz E-UTRA channel bandwidth allocated within 1744.9MHz and 1784.9MHz. NOTE 11: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 12: Void. NOTE13: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band. NOTE14:This requirement is applicable for any channel bandwidths within the range 2500 – 2570 MHz with the following restriction: for carriers of 15 MHz bandwidth when carrier centre frequency is within the range 2560.5 – 2562.5 MHz and for carriers of 20 MHz bandwidth when carrier centre frequency is within the range 2552 – 2560 MHz the requirement is applicable only for an uplink transmission bandwidth less than or equal to 54 RB. NOTE 15-21:Void. NOTE 22: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies. NOTE 23: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48.

Table 6.6.3.2A.2.5-3: Requirements for dual-uplink inter-band carrier aggregation for Rel-14

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
CA_1A-3A	E-UTRA Band 1, 32, 43, 65	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-3A	E-UTRA band 21	F_{DL_low}	–	F_{DL_high}	-50	1	10
CA_1A-5A	E-UTRA Band 22, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-7A	E-UTRA Band 32	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-8A	E-UTRA band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_1A-18A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-19A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-21A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-21A	Frequency range	945	–	960	-50	1
CA_1A-26A	E-UTRA Band 22, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-28A	E-UTRA Band 7, 31, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	470	–	694	-42	8	3, 22
	Frequency range	470	–	710	-26.2	6	23
CA_1A-42A	E-UTRA Band 11, 21, 31, 32	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-4A	E-UTRA Band 4, 10, 22, 24, 66, 70	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-5A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-5A	E-UTRA Band 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-7A	E-UTRA Band 29	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-12A	E-UTRA Band 41	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-13A	E-UTRA Band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-5A	E-UTRA Band 5, 7, 8, 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-5A	E-UTRA band 26	859	–	869	-27	1
CA_3A-7A	E-UTRA Band 5, 8, 20, 26, 27, 28, 44, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-7A	E-UTRA band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_3A-8A	E-UTRA Band 20, 28, 38, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 7, 22, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	860	–	890	-40	1	3,11,17
CA_3A-19A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
	Frequency range	2595	–	2645	-50	1
CA_3A-20A	E-UTRA Band 7, 8	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-20A	E-UTRA Band 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_3A-26A	E-UTRA Band 5, 7, 26	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
CA_3A-28A	E-UTRA Band 1, 22, 42, 43, 65	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}	–	F_{DL_high}	-50	1	5, 6
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 5, 7, 8, 11, 18, 19, 20, 21, 26, 27, 31, 34, 38, 40, 41	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3
	Frequency range	470	–	710	-26.2	6	23
CA_3A-41A	E-UTRA Band 5, 8, 20, 26, 27, 28, 44, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-41A	E-UTRA Band 18, 19	F_{DL_low}	–	F_{DL_high}	-50	1	18
CA_4A-5A	E-UTRA Band 5, 7	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 26	859	–	869	-27	1
	E-UTRA band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_4A-7A	E-UTRA Band 5, 12, 13, 14, 17, 26, 27, 28	F_{DL_low}	–	F_{DL_high}	-50	1
CA_4A-7A	E-UTRA band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_4A-12A	No requirement
CA_4A-13A	E-UTRA Band 7, 41	F_{DL_low}	–	F_{DL_high}	-50	1
CA_4A-17A	No requirement
CA_5A-7A	E-UTRA Band 5, 28, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_5A-7A	E-UTRA band 26	859	–	869	-27	1
CA_5A-12A	E-UTRA Band 24, 30	F_{DL_low}	–	F_{DL_high}	-50	1
CA_5A-17A	E-UTRA Band 24, 30	F_{DL_low}	–	F_{DL_high}	-50	1
CA_7A-20A	E-UTRA Band 28	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_7A-28A	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1
CA_18A-28A	Frequency range	470	–	710	-26.2	6	23
CA_19A-21A	No requirement
CA_39A-41A	E-UTRA Band 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
CA_41A-42A	E-UTRA Band 3, 5, 8, 26, 28, 33, 39, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	18
	Frequency range	1839.9	–	1879.9	-50	1	18
	Frequency range	1884.5	–	1915.7	-41	0.3	4, 18
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. In case the exceptions are allowed due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3 or 4 for the 2^nd, 3^rd or 4^th harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3: These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the aggregated channel bandwidth. NOTE 4:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. NOTE 5-9:Void NOTE10: This requirement applies for 5, 10, 15 and 20 MHz E-UTRA channel bandwidth allocated within 1744.9MHz and 1784.9MHz. NOTE 11: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 12-16: Void NOTE 17: This requirement is applicable only when Band 3 transmission frequency is less than or equal to 1765 MHz. NOTE 18: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz NOTE 19-21: Void NOTE 22: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies. NOTE 23: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48.

Table 6.6.3.2A.2.5-4: Requirements for dual-uplink inter-band carrier aggregation for Rel-15

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
CA_1A-3A	E-UTRA Band 1, 32, 43, 50, 65, 74, 75	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-3A	E-UTRA band 21	F_{DL_low}	–	F_{DL_high}	-50	1	10
CA_1A-5A	E-UTRA Band 22, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-7A	E-UTRA Band 32, 50, 51, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-8A	E-UTRA band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_1A-18A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-19A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-21A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-21A	Frequency range	945	–	960	-50	1
CA_1A-26A	E-UTRA Band 22, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-28A	E-UTRA Band 7, 31, 41, 72, 73	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	470	–	694	-42	8	3, 22
	Frequency range	470	–	710	-26.2	6	23
CA_1A-42A	E-UTRA Band 11, 21, 31, 32, 50, 51, 72, 73, 74, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-4A	E-UTRA Band 4, 10, 22, 24, 50, 66, 70, 74	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-5A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-5A	E-UTRA Band 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-7A	E-UTRA Band 29	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-12A	E-UTRA Band 41	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-13A	E-UTRA Band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-5A	E-UTRA Band 5, 7, 8, 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-5A	E-UTRA band 26	859	–	869	-27	1
CA_3A-7A	E-UTRA Band 5, 8, 20, 26, 27, 28, 44, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-7A	E-UTRA band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_3A-8A	E-UTRA Band 20, 28, 38, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 7, 22, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	860	–	890	-40	1	3,11,17
CA_3A-19A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
	Frequency range	2595	–	2645	-50	1
CA_3A-20A	E-UTRA Band 7, 8	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-20A	E-UTRA Band 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_3A-26A	E-UTRA Band 5, 7, 26	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
CA_3A-28A	E-UTRA Band 1, 11, 18, 19, 21, 22, 42, 43, 50, 51, 52, 65, 74, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}	–	F_{DL_high}	-50	1	5, 6
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 5, 7, 8, 20, 26, 27, 31, 34, 38, 40, 41, 72, 73	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3
	Frequency range	470	–	710	-26.2	6	23
CA_3A-41A	E-UTRA Band 5, 8, 20, 26, 27, 28, 44, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-41A	E-UTRA Band 18, 19	F_{DL_low}	–	F_{DL_high}	-50	1	18
CA_4A-5A	E-UTRA Band 5, 7	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 26	859	–	869	-27	1
	E-UTRA band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_4A-7A	E-UTRA Band 5, 12, 13, 14, 17, 26, 27, 28	F_{DL_low}	–	F_{DL_high}	-50	1
CA_4A-7A	E-UTRA band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_4A-12A	No requirement
CA_4A-13A	E-UTRA Band 7, 41	F_{DL_low}	–	F_{DL_high}	-50	1
CA_4A-17A	No requirement
CA_5A-7A	E-UTRA Band 5, 28, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_5A-7A	E-UTRA band 26	859	–	869	-27	1
CA_5A-12A	E-UTRA Band 24, 30	F_{DL_low}	–	F_{DL_high}	-50	1
CA_5A-17A	E-UTRA Band 24, 30	F_{DL_low}	–	F_{DL_high}	-50	1
CA_7A-20A	E-UTRA Band 28	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_7A-28A	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1
CA_11A-18A	E-UTRA Band 1, 3, 11, 18, 19, 21, 28, 34, 42, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	890	-40	1	3
	Frequency range	1884.5	–	1915.7	-41	0.3	4
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
	Frequency range	945	–	960	-50	1
CA_18A-28A	Frequency range	470	–	710	-26.2	6	23
CA_19A-21A	No requirement
CA_39A-41A	E-UTRA Band 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
CA_41A-42A	E-UTRA Band 3, 5, 8, 26, 28, 33, 39, 44, 50, 51, 74	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	18
	Frequency range	1839.9	–	1879.9	-50	1	18
	Frequency range	1884.5	–	1915.7	-41	0.3	4, 18
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. In case the exceptions are allowed due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3 or 4 for the 2^nd, 3^rd or 4^th harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3: These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the aggregated channel bandwidth. NOTE 4:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. NOTE 5-9:Void. NOTE10: This requirement applies for 5, 10, 15 and 20 MHz E-UTRA channel bandwidth allocated within 1744.9MHz and 1784.9MHz. NOTE 11: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 12-16: Void. NOTE 17: This requirement is applicable only when Band 3 transmission frequency is less than or equal to 1765 MHz. NOTE 18: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz NOTE 19-21: Void NOTE 22: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies. NOTE 23: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48. NOTE 24-25:Void.

Table 6.6.3.2A.2.5-5: Requirements for dual-uplink inter-band carrier aggregation for Rel-16

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
CA_1A-3A	E-UTRA Band 1, 32, 43, 50, 65, 74, 75	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-3A	E-UTRA band 21	F_{DL_low}	–	F_{DL_high}	-50	1	10
CA_1A-5A	E-UTRA Band 22, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-7A	E-UTRA Band 32, 50, 51, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-8A	E-UTRA band 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_1A-18A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-19A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-21A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-21A	Frequency range	945	–	960	-50	1
CA_1A-26A	E-UTRA Band 22, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1
CA_1A-28A	E-UTRA Band 7, 31, 41, 72, 73	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	470	–	694	-42	8	3, 22
	Frequency range	470	–	710	-26.2	6	23
CA_1A-42A	E-UTRA Band 11, 21, 31, 32, 50, 51, 72, 73, 74, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-4A	E-UTRA Band 4, 10, 22, 24, 50, 66, 70, 74	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 2, 25	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-5A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-5A	E-UTRA Band 41, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_2A-7A	E-UTRA Band 29	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-12A	E-UTRA Band 41, 53	F_{DL_low}	–	F_{DL_high}	-50	1
CA_2A-13A	E-UTRA Band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-5A	E-UTRA Band 5, 7, 8, 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-5A	E-UTRA band 26	859	–	869	-27	1
CA_3A-7A	E-UTRA Band 5, 8, 20, 26, 27, 28, 44, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-7A	E-UTRA band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_3A-8A	E-UTRA Band 20, 28, 38, 44	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 7, 22, 41, 42, 43	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	860	–	890	-40	1	3,11,17
CA_3A-19A	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
	Frequency range	2595	–	2645	-50	1
CA_3A-20A	E-UTRA Band 7, 8	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-20A	E-UTRA Band 38, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_3A-26A	E-UTRA Band 5, 7, 26	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
	Frequency range	945	–	960	-50	1
CA_3A-28A	E-UTRA Band 1, 11, 18, 19, 21, 22, 42, 43, 50, 51, 52, 65, 74, 75, 76	F_{DL_low}	–	F_{DL_high}	-50	1	2
	E-UTRA Band 1	F_{DL_low}	–	F_{DL_high}	-50	1	5, 6
	E-UTRA band 3	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 5, 7, 8, 20, 26, 27, 31, 34, 38, 40, 41, 72, 73	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	1884.5	–	1915.7	-41	0.3
	Frequency range	470	–	710	-26.2	6	23
CA_3A-41A	E-UTRA Band 5, 8, 20, 26, 27, 28, 44, 67	F_{DL_low}	–	F_{DL_high}	-50	1
CA_3A-41A	E-UTRA Band 18, 19	F_{DL_low}	–	F_{DL_high}	-50	1	18
CA_4A-5A	E-UTRA Band 5, 7	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 26	859	–	869	-27	1
	E-UTRA band 41, 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_4A-7A	E-UTRA Band 5, 12, 13, 14, 17, 26, 27, 28	F_{DL_low}	–	F_{DL_high}	-50	1
CA_4A-7A	E-UTRA band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_4A-12A	No requirement
CA_4A-13A	E-UTRA Band 7, 41, 53	F_{DL_low}	–	F_{DL_high}	-50	1
CA_4A-17A	No requirement
CA_5A-7A	E-UTRA Band 5, 28, 42	F_{DL_low}	–	F_{DL_high}	-50	1
CA_5A-7A	E-UTRA band 26	859	–	869	-27	1
CA_5A-12A	E-UTRA Band 24, 30	F_{DL_low}	–	F_{DL_high}	-50	1
CA_5A-17A	E-UTRA Band 24, 30	F_{DL_low}	–	F_{DL_high}	-50	1
CA_7A-20A	E-UTRA Band 28	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 20	F_{DL_low}	–	F_{DL_high}	-50	1	3
	E-UTRA Band 42	F_{DL_low}	–	F_{DL_high}	-50	1	2
CA_7A-28A	E-UTRA Band 3	F_{DL_low}	–	F_{DL_high}	-50	1
CA_11A-18A	E-UTRA Band 1, 3, 11, 18, 19, 21, 28, 34, 42, 65	F_{DL_low}	–	F_{DL_high}	-50	1
	Frequency range	860	–	890	-40	1	3
	Frequency range	1884.5	–	1915.7	-41	0.3	4
	Frequency range	2545	–	2575	-50	1
	Frequency range	2595	–	2645	-50	1
	Frequency range	945	–	960	-50	1
CA_18A-28A	Frequency range	470	–	710	-26.2	6	23
CA_19A-21A	No requirement
CA_39A-41A	E-UTRA Band 42, 44	F_{DL_low}	–	F_{DL_high}	-50	1
CA_41A-42A	E-UTRA Band 3, 5, 8, 26, 28, 33, 39, 44, 50, 51, 74	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	18
	Frequency range	1839.9	–	1879.9	-50	1	18
	Frequency range	1884.5	–	1915.7	-41	0.3	4, 18
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. In case the exceptions are allowed due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3 or 4 for the 2^nd, 3^rd or 4^th harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3: These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1-1 and Table 6.6.3.1A-1 from the edge of the aggregated channel bandwidth. NOTE 4:Applicable when co-existence with PHS system operating in 1884.5 -1915.7MHz. NOTE 5-9:Void. NOTE10: This requirement applies for 5, 10, 15 and 20 MHz E-UTRA channel bandwidth allocated within 1744.9MHz and 1784.9MHz. NOTE 11: This requirement is applicable only for the following cases: – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 902.5 MHz ≤ F_c < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB – for carriers of 5 MHz channel bandwidth when carrier centre frequency (F_c) is within the range 907.5 MHz ≤ F_c ≤ 912.5 MHz without any restriction on uplink transmission bandwidth. – for carriers of 10 MHz channel bandwidth when carrier centre frequency (F_c) is F_c = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3. NOTE 12-16: Void. NOTE 17: This requirement is applicable only when Band 3 transmission frequency is less than or equal to 1765 MHz. NOTE 18: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz NOTE 19-21: Void NOTE 22: This requirement is applicable in the case of a 10 MHz E-UTRA carrier confined within 703 MHz and 733 MHz, otherwise the requirement of -25 dBm with a measurement bandwidth of 8 MHz applies. NOTE 23: This requirement is applicable for 5 and 10 MHz E-UTRA channel bandwidth allocated within 718-728MHz. For carriers of 10 MHz bandwidth, this requirement applies for an uplink transmission bandwidth less than or equal to 30 RB with RBstart > 1 and RBstart<48. NOTE 24-25:Void.

6.6.3.2A.3 Spurious emission band UE co-existence for CA (intra-band non-contiguous DL CA and UL CA)

6.6.3.2A.3.1 Test purpose

6.6.3.2A.3.2 Test applicability

This test case applies to all types of E-UTRA UE release 11 and forward that support intra-band non-contiguous DL CA and UL CA.

6.6.3.2A.3.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.2A.0.

6.6.3.2A.3.4 Test description

6.6.3.2A.3.4.1 Initial conditions

Same as in clause 6.6.3.2A.1.4.1 with the following exceptions:

– Instead of Table 6.6.3.2A.1.4.1-1 🡪 use Table 6.6.3.2A.3.4.1-1.

– Instead of clause 6.6.3.2A.1.4.3 🡪 use clause 6.6.3.2A.3.4.3.

Table 6.6.3.2A.3.4.1-1: Test Configuration Table

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1					NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.					Refer to test points A: N/A (Range is not relevant), Maximum Wgap(low + high frequency)
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.					Refer to test points Test only test points with Lowest N_RB for PCC and SCC Highest N_RB for PCC and SCC
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		W_gap[MHz]	DL Allocation		UL Allocation
ID	PCC N_RB	SCCs N_RB	W_gap[MHz]	CC MOD	PCC & SCC RB allocation	CC MOD	PCC N_{RB_alloc} (L_CRB @ RB_start)	CC MOD	SCC N_{RB_alloc} (L_CRB @ RB_start)
Test Parameters for CA_4A-4A Configurations
1	25	25	35	N/A	N/A	QPSK	P_1@0	QPSK	S_1@24
2	25	25	35	N/A	N/A	QPSK	P_25@0	QPSK	S_25@0
3	100	100	5	N/A	N/A	QPSK	P_1@0	QPSK	S_1@99
4	100	100	5	N/A	N/A	QPSK	P_100@0	QPSK	S_100@0

6.6.3.2A.3.4.2 Test procedure

Same test procedure as in clause 6.6.3.2A.1.4.2 with the following exceptions:

– Instead of Table 6.6.3.2A.1.4.1-1 🡪 use Table 6.6.3.2A.3.4.1-1.

– Instead of Table 6.6.3.2A.0-2a to 6.6.3.2A.0-2c 🡪 use Table 6.6.3.2A.0-3

– Instead of clause 6.6.3.2A.1.4.3 🡪 use clause 6.6.3.2A.3.4.3.

6.6.3.2A.3.4.3 Message contents

Message contents are according to TS 36.508 [7] clause 4.6. In test procedure step 2, for SCC configuration there are no additional message contents.

6.6.3.2A.3.5 Test requirement

Test requirements for Spurious Emissions UE Co-existence are the same as the minimum requirements and are not repeated in this section.

The measured average power of spurious emission, derived in step 6, shall not exceed the described value in Table 6.6.3.2A.3.5-1.

The requirements for the UE are release specific and can be found in Table 6.6.3.2A.0-3. If the UE supports a band, which is not defined in the table corresponding UE’s release, the requirements for this band are taken from the table of earliest release where requirements for this band are defined. This has been described in following Table 6.6.3.2A.3.5-1.

Table 6.6.3.2A.3.5-1: UE Requirements according to UE E-UTRA release and supported E-UTRA CA configuration

E-UTRA CA Configuration	UE Requirements per release
	Rel-12
CA_4A-4A	Table 6.6.3.2A.0-3

6.6.3.2A.4 Spurious emission band UE co-existence for CA (3UL CA)

Editor’s notes: This test case is incomplete. The following items are missing or incomplete:

– Additional TP analysis needs to be added to TR36.905

6.6.3.2A.4.1 Test purpose

6.6.3.2A.4.2 Test applicability

This test case applies to all types of E-UTRA UE release 13 and forward that support intra-band contiguous or inter-band and 3UL CA.

6.6.3.2A.4.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.2A.0.

6.6.3.2A.4.4 Test description

6.6.3.2A.4.4.1 Initial conditions

Same as in clause 6.6.3.2A.1.4.1 with the following exceptions:

– Instead of Table 6.6.3.2A.1.4.1-1 🡪 use Table 6.6.3.2A.4.4.1-1 to Table 6.6.3.2A.4.4.1-2.

– Instead of clause 6.6.3.2A.1.4.3 🡪 use clause 6.6.3.2A.4.4.3.

Table 6.6.3.2A.4.4.1-1: Intra Band contiguous CA Test Configuration Table

Initial Conditions

Test Environment as specified in TS 36.508[7] subclause 4.1

Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.

For test frequencies refer to “Range” columns.

Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.

Refer to “PCC N_RB”and “SCC N_RB” columns

Test Parameters for CA Configurations

CA Configuration / N_{RB_agg}

DL Allocation

UL Allocation

CA Configuration

CC MOD

PCC & SCC RB allocation

CC MOD

PCC & SCC1 & SCC2 RB allocations(L_CRB @ RB_start)

PCC

SCC1

SCC2

PCC N_RB

SCC1 N_RB

SCC2 N_RB

PCC

SCC1

SCC2

Band

Range

Band

Range

Band

Range

Default Test Settings for a CA_XD Configuration

Low

Highest

N_RB

Highest

N_RB

Highest

N_RB

QPSK

N/A

QPSK

1@0

Low

Highest

N_RB

Highest

N_RB

Highest

N_RB

QPSK

N/A

QPSK

full@0

High

Highest

N_RB

Highest

N_RB

Highest

N_RB

QPSK

N/A

QPSK

1@0

High

Highest

N_RB

Highest

N_RB

Highest

N_RB

QPSK

N/A

QPSK

full@0

Note 1: CA Configuration Test CC Combination test settings are checked separately for each CA Configuration.

Note 2: Use CA Configuration – specific test points if present in the table. Otherwise use the Default Test Settings test points.

Table 6.6.3.2A.4.4.1-2: inter-band CA Test Configuration Table

Initial Conditions

Test Environment as specified in TS 36.508[7] subclause 4.1

Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.

For test frequencies refer to “Range” columns.

Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.

Refer to “PCC N_RB”and “SCC N_RB” columns

Test Parameters for CA Configurations

CA Configuration / N_{RB_agg}

DL Allocation

UL Allocation

CA Configuration

CC MOD

PCC & SCC RB allocation

CC MOD

PCC & SCC1 & SCC2 RB allocations(L_CRB @ RB_start)

PCC

SCC1

SCC2

PCC N_RB

SCC1 N_RB

SCC2 N_RB

PCC

SCC1

SCC2

Band

Range

Band

Range

Band

Range

Default Test Settings for a CA_XA-YC Configuration

Low

Highest

N_RB

Highest

N_RB

Highest

N_RB

QPSK

N/A

QPSK

1@0

Low

Highest

N_RB

Highest

N_RB

Highest

N_RB

QPSK

N/A

QPSK

full@0

High

Highest

N_RB

Highest

N_RB

Highest

N_RB

QPSK

N/A

QPSK

1@0

High

Highest

N_RB

Highest

N_RB

Highest

N_RB

QPSK

N/A

QPSK

full@0

Default Test Settings for a CA_XC-YA Configuration

Low

Highest

N_RB

Highest

N_RB

Highest

N_RB

QPSK

N/A

QPSK

1@0

Low

Highest

N_RB

Highest

N_RB

Highest

N_RB

QPSK

N/A

QPSK

full@0

High

Highest

N_RB

Highest

N_RB

Highest

N_RB

QPSK

N/A

QPSK

1@0

High

Highest

N_RB

Highest

N_RB

Highest

N_RB

QPSK

N/A

QPSK

full@0

Note 1: CA Configuration Test CC Combination test settings are checked separately for each CA Configuration.

Note 2: Use CA Configuration – specific test points if present in the table. Otherwise use the Default Test Settings test points.

Note 3: X,Y correspond to the different bands in the CA Configuration. E.g. for CA_39A-41A,X=39,Y=41.

6.6.3.2A.4.4.2 Test procedure

1. Configure SCC according to Annex C.0, C.1 and Annex C.3.0 for all downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4. Message contents are defined in clause 6.6.3.2A.4.4.3

3. SS activates SCC by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 6.6.3.2A.4.4.1-1 and Table 6.6.3.2A.4.4.1-2 on all PCC and SCCs. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

5. Send continuously uplink power control “up” commands in every uplink scheduling information to the UE until the UE transmits at P_UMAX level.

6. Measure the power of the transmitted signal with a measurement filter of bandwidths according to Tables in 6.6.3.2A.4.5-1. The centre frequency of the filter shall be stepped in contiguous steps according to Tables in 6.6.3.2A.4.5-1. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

6.6.3.2A.4.4.3 Message contents

Message contents are according to TS 36.508 [7] clause 4.6. In test procedure step 2, for SCC configuration there are no additional message contents.

6.6.3.2A.4.5 Test requirement

Test requirements for Spurious Emissions UE Co-existence are the same as the minimum requirements and are not repeated in this section.

The measured average power of spurious emission, derived in step 6, shall not exceed the described value in Tables 6.6.3.2A.4.5-1.

The requirements for the UE are release specific and can be found in Tables 6.6.3.2A.0-2a to 6.6.3.2A.0-2f for intra-band contiguous carrier aggregation and Tables 6.6.3.2A.0-1a to 6.6.3.2A.0-1e for inter-band carrier aggregation. If the UE support a band, which is not defined in the table corresponding UE’s release, the requirements for this band are taken from the table of earliest release where requirements for this band are defined. This has been described in following Table 6.6.3.2A.4.5-1.

Table 6.6.3.2A.4.5-1: UE Requirements according to UE E-UTRA release and supported E-UTRA CA configuration

E-UTRA CA Configuration	UE Requirements per release
	Rel-13	Rel-14	Rel-15	Rel-16
CA_40D	N/A	Table 6.6.3.2A.0-2e	Table 6.6.3.2A.0-2f	tbd
CA_39A-41C	Table 6.6.3.2A.0-1b	Table 6.6.3.2A.0-1c	Table 6.6.3.2A.0-1d	Table 6.6.3.2A.0-1e
CA_39C-41A	Table 6.6.3.2A.0-1b	Table 6.6.3.2A.0-1c	Table 6.6.3.2A.0-1d	Table 6.6.3.2A.0-1e

6.6.3.2A.5 Spurious emission band UE co-existence for CA (4UL CA)

Editor’s Note: This test case is incomplete. The following items are missing or are incomplete:

Test configuration table is TBD, because TP analysis in TR 36.905 is incomplete.
Release dependent approach is missing.

6.6.3.2A.5.1 Test purpose

6.6.3.2A.5.2 Test applicability

This test case applies to all types of E-UTRA UE release 11 and forward that support inter-band and 4UL CA.

6.6.3.2A.5.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.2A.0.

6.6.3.2A.5.4 Test description

6.6.3.2A.2.5.1 Initial conditions

Same as in clause 6.6.3.2A.1.4.1 with the following exceptions:

– Instead of Table 5.4.2A.1-1🡪 use Table 5.4.2A.1-2.

– Instead of Table 6.6.3.2A.1.4.1-1 🡪 use Table 6.6.3.2A.5.4.1-1.

– Instead of clause 6.6.3.2A.1.4.3 use clause 6.6.3.2A.5.4.3.

Table 6.6.3.2A.5.4.1-1: Test Configuration Table

Initial Conditions

Test Environment as specified in TS 36.508[7] subclause 4.1

Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes.

For test frequencies refer to “Range” columns.

Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.

Refer to “PCC NRB”and “SCC NRB ” columns

Test Parameters for CA Configurations

CA Configuration / N_{RB_agg}

DL Allocation

UL Allocation (Note 2)

CA Configuration

PCC N_RB

SCC1 N_RB

SCC2 N_RB

SCC3 N_RB

CC MOD

PCC & SCCs

RB allocation

CC MOD

PCC & SCC RB allocations
(L_CRB @ RB_start)

PCC & SCC1

SCC2 & SCC3

PCC

SCC1

SCC2

SCC3

Band

Range

Band

Range

Test Settings for CA_41C-42C Configuration

TBD

100

QPSK

TBD

100

QPSK

TBD

Note 1: CA Configuration Test CC Combination test settings are checked separately for each CA Configuration.

Note 2: Use CA Configuration – specific test points if present in the table. Otherwise use the Default Test Settings test points.

6.6.3.2A.5.4.2 Test procedure

1. Configure SCCs according to Annex C.0, C.1 and Annex C.3.0 for all downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4. Message contents are defined in clause 6.6.3.2A.5.4.3

3. SS activates SCCs by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 6.6.3.2A.5.4.1-1 on PCC and SCCs. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

5. Send continuously uplink power control “up” commands in every uplink scheduling information to the UE until the UE transmits at P_UMAX level.

6. Measure the power of the transmitted signal with a measurement filter of bandwidths according to Table 6.6.3.2A.2.5-1. The centre frequency of the filter shall be stepped in contiguous steps according to the same table. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

6.6.3.2A.5.5 Test requirement

The measured average power of spurious emission, derived in step 6, shall not exceed the described value in Tables 6.6.3.2A.5.5-1.

Table 6.6.3.2A.5.5-1: Requirements for dual-uplink inter-band carrier aggregation

E-UTRA CA Configuration	Spurious emission
E-UTRA CA Configuration	Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Note
CA_41C-42C	E-UTRA Band 3, 5, 8, 26, 28, 33, 39, 44, 45, 50, 51, 74	F_{DL_low}	–	F_{DL_high}	-50	1
	E-UTRA Band 9, 11, 18, 19, 21	F_{DL_low}	–	F_{DL_high}	-50	1	3
	NR Band n79				-50	1	2
NOTE 1: F_{DL_low} and F_{DL_high} refer to each E-UTRA frequency band specified in Table 5.5-1 NOTE 2:As exceptions, measurements with a level up to the applicable requirements defined in Table 6.6.3.1-2 are permitted for each assigned E-UTRA carrier used in the measurement due to 2^nd, 3^rd, 4^th [or 5^th] harmonic spurious emissions. In case the exceptions are allowed due to spreading of the harmonic emission the exception is also allowed for the first 1 MHz frequency range immediately outside the harmonic emission on both sides of the harmonic emission. This results in an overall exception interval centred at the harmonic emission of (2MHz + N x L_CRB x 180kHz), where N is 2, 3 or 4 for the 2^nd, 3^rd or 4^th harmonic respectively. The exception is allowed if the measurement bandwidth (MBW) totally or partially overlaps the overall exception interval. NOTE 3: This requirement applies when the E-UTRA carrier is confined within 2545-2575MHz or 2595-2645MHz and the channel bandwidth is 10 or 20 MHz

6.6.3.3 Additional spurious emissions

Editor’s notes: This test case is incomplete. The following items are missing or incomplete:

– Test configuration table for NS_38 and NS_39 is not defined.

6.6.3.3.1 Test purpose

To verify that UE transmitter does not cause unacceptable interference to other channels or other systems in terms of transmitter spurious emissions under the deployment scenarios where additional requirements are specified.

6.6.3.3.2 Test applicability

This test case applies to all types of E-UTRA UE release 8 and forward.

6.6.3.3.3 Minimum conformance requirements

These requirements are specified in terms of an additional spectrum emission requirement. Additional spurious emission requirements are signalled by the network to indicate that the UE shall meet an additional requirement for a specific deployment scenario as part of the cell handover/broadcast message.

6.6.3.3.3.1 Minimum requirement (network signalled value “NS_04”)

When "NS 04" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.1-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.1-1: Additional requirements

Frequency band	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
Frequency band	5, 10, 15, 20 MHz	Measurement bandwidth
2490.5 MHz ≤ f < 2495 MHz	-13	1 MHz
9 kHz < f < 2490.5 MHz	-25	1 MHz

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.19.

6.6.3.3.3.2 Minimum conformance requirements (network signalled value "NS_05")

When "NS_05" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.2-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.2-1: Additional requirements (PHS)

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)				Measurement bandwidth
Frequency band (MHz)	5 MHz	10 MHz	15 MHz	20 MHz	Measurement bandwidth
1884.5 f 1915.7^*1	-41	-41	-41	-41	300 KHz
Note 1: Applicable when the lower edge of the assigned E-UTRA UL channel bandwidth frequency is larger than or equal to the upper edge of PHS band (1915.7 MHz) + 4 MHz + the Channel BW assigned, where Channel BW is as defined in sub-clause 5.4.2. Additional restrictions apply for operations below this point.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.1.

6.6.3.3.3.3 Minimum conformance requirements (network signalled value "NS_07")

When "NS_07" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.3-1. These requirements also apply for the frequency ranges that are less than Δf_OOB(MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.3-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	10 MHz
769 ≤ f ≤ 775	-57	6.25 kHz
Note: The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.2.

6.6.3.3.3.4 Minimum requirement (network signalled value "NS_08")

When "NS_08" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.4-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.4-1: Additional requirement

Frequency band

(MHz)

Channel bandwidth / Spectrum emission limit (dBm)

Measurement bandwidth

5MHz

10MHz

15MHz

860 ≤ f ≤ 895

-40

1 MHz

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.3.

6.6.3.3.3.5 Minimum requirement (network signalled value "NS_09")

When "NS 09" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.5-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.5-1: Additional requirement

Frequency band

(MHz)

Channel bandwidth / Spectrum emission limit (dBm)

Measurement bandwidth

5MHz

10MHz

15MHz

1475.9 ≤ f ≤ 1510.9

-35

1 MHz

NOTE 1: To improve measurement accuracy, A-MPR values for NS_09 specified in Table 6.2.4.3-1 in sub-clause 6.2.4 are derived based on 100 kHz RBW.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.4.

6.6.3.3.3.6 Minimum requirement (network signalled value "NS_11")

When “NS_11” is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.6-1. These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.6-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth	Note
Frequency band (MHz)	1.4, 3, 5, 10, 15, 20 MHz	Measurement bandwidth	Note
E-UTRA Band 2	-50	1 MHz
1998 ≤ f ≤ 1999	-21	1 MHz
1997 ≤ f < 1998	-27	1 MHz
1996 ≤ f < 1997	-32	1 MHz
1995 ≤ f < 1996	-37	1 MHz
1990 ≤ f < 1995	-40	1 MHz

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.13.

6.6.3.3.3.7 Minimum requirement (network signalled value "NS_12")

When "NS 12" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.7-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.7-1: Additional requirements

Frequency band (MHz)	Channel bandwidth/ Spectrum emission limit (dBm)	Measurement bandwidth
	1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz
806 ≤ f ≤ 813.5	-42	6.25 kHz
NOTE 1: The requirement applies for E-UTRA carriers with lower channel edge at or above 814.2 MHz. NOTE 2: The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.5.

6.6.3.3.3.8 Minimum requirement (network signalled value "NS_13")

When "NS 13" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.8-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.8-1: Additional requirements

Frequency band (MHz)	Channel bandwidth/ Spectrum emission limit (dBm)	Measurement bandwidth
	1.4, 3, 5 MHz
806 ≤ f ≤ 816	-42	6.25 kHz
NOTE 1: The requirement applies for E-UTRA carriers with lower channel edge at or above 819 MHz. NOTE 2: The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.6.

6.6.3.3.3.9 Minimum requirement (network signalled value "NS_14")

When "NS 14" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.9-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.9-1: Additional requirements

Frequency band (MHz)	Channel bandwidth/ Spectrum emission limit (dBm)	Measurement bandwidth
	10 MHz, 15 MHz
806 ≤ f ≤ 816	-42	6.25 kHz
NOTE 1: The requirement applies for E-UTRA carriers with lower channel edge at or above 824 MHz. NOTE 2: The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.7.

6.6.3.3.3.10 Minimum requirement (network signalled value "NS_15")

When "NS 15" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.10-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.10-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth	Note
	1.4, 3, 5, 10, 15 MHz
851 ≤ f ≤ 859	-53	6.25 kHz	1
Note 1: The emissions measurement shall be sufficiently power averaged to ensure standard deviation < 0.5 dB.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.8.

6.6.3.3.3.11 Minimum requirement (network signalled value "NS_16")

When “NS_16” is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.11-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.11-1: Additional requirements

Frequency band

(MHz)

Channel bandwidth / Spectrum emission limit (dBm)

Measurement bandwidth

Note

1.4, 3, 5, 10 MHz

790 ≤ f ≤ 803

-32

1 MHz

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.9.

6.6.3.3.3.12 Minimum requirement (network signalled value "NS_17")

When “NS_17” is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.12-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.12-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth	Note
	5, 10 MHz
470 ≤ f ≤ 710	-26.2	6 MHz	1
Note 1: Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.10.

6.6.3.3.3.13 Minimum requirement (network signalled value "NS_18")

When “NS_18” is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.13-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.13-1: Additional requirements

Frequency band

(MHz)

Channel bandwidth / Spectrum emission limit (dBm)

Measurement bandwidth

Note

5, 10, 15, 20 MHz

692 ≤ f ≤ 698

-26.2

6 MHz

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.11.

6.6.3.3.3.14 Minimum requirement (network signalled value "NS_19")

When “NS_19” is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.14-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.14-1: Additional requirements

Frequency band

(MHz)

Channel bandwidth / Spectrum emission limit (dBm)

Measurement bandwidth

Note

3, 5, 10, 15, 20 MHz

662 ≤ f ≤ 694

-25

8 MHz

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.12.

6.6.3.3.3.15 Minimum requirement (network signalled value "NS_20")

When “NS_20” is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.15-1. These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.15-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth	Note
Frequency band (MHz)	5, 10, 15, 20 MHz	Measurement bandwidth	Note
1990 ≤ f < 1999	-40	1 MHz
1999 ≤ f ≤ 2000	-40	Note 1
Note 1: The measurement bandwidth is 1% of the applicable E-UTRA channel bandwidth (5.4.2.1-1).

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.14.

6.6.3.3.3.16 Minimum requirement (network signalled value “NS_21”)

When “NS_21” is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.16-1. These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.16-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
Frequency band (MHz)	5, 10 MHz	Measurement bandwidth
2200 ≤ f < 2288	-40	1 MHz
2288 ≤ f < 2292	-37	1 MHz
2292 ≤ f < 2296	-31	1 MHz
2296 ≤ f < 2300	-25	1 MHz
2320 ≤ f < 2324	-25	1 MHz
2324 ≤ f < 2328	-31	1 MHz
2328 ≤ f < 2332	-37	1 MHz
2332 ≤ f ≤ 2395	-40	1 MHz

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.15.

6.6.3.3.3.17 Minimum requirement (network signalled value “NS_22”)

When "NS_22" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.17-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.17-1: Additional requirement

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	MBW
	5, 10, 15, 20 MHz
3400 ≤ f ≤ 3800	-23 (NOTE 1, NOTE 3)	5 MHz
	-40 (NOTE 2)	1 MHz
NOTE 1: This requirement applies within an offset between 5 MHz and 25 MHz from the lower and from the upper edge of the channel bandwidth, whenever these frequencies overlap with the specified frequency band. NOTE 2: This requirement applies from 3400 MHz to 25 MHz below the lower E-UTRA channel edge and from 25 MHz above the upper E-UTRA channel edge to 3800 MHz. NOTE 3: This emission limit might imply risk of harmful interference to UE(s) operating in the protected operating band

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.16.

6.6.3.3.3.18 Minimum requirement (network signalled value “NS_23”)

When "NS_23" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.18-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

6.6.3.3.3.18-1: Additional requirement

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	MBW
	5, 10, 15, 20 MHz
3400 ≤ f ≤ 3800	-23 (NOTE 1, NOTE 4)	5 MHz
	-40 (NOTE 2)	1 MHz
NOTE 1: This requirement applies within an offset between 5 MHz + F_{offset_NS_23} and 25 MHz + F_{offset_NS_23} from the lower and from the upper edges of the channel bandwidth, whenever these frequencies overlap with the specified frequency band. NOTE 2: This requirement applies from 3400 MHz to 25 MHz + F_{offset_NS_23} below the lower E-UTRA channel edge and from 25 MHz + Foffset_{_NS_23} above the upper E-UTRA channel edge to 3800 MHz. NOTE 3: F_{offset_NS_23} is: 0 MHz for 5 MHz channel BW, 5 MHz for 10 MHz channel BW, 9 MHz for 15 MHz channel BW and 12 MHz for 20 MHz channel BW. NOTE 4: This emission limit might imply risk of harmful interference to UE(s) operating in the protected operating band.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.17.

6.6.3.3.3.19 Minimum requirement (network signalled value “NS_24”)

When "NS_24" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.19-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.19-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	5 MHz, 10 MHz, 15 MHz, 20 MHz
Band 34	-50	MHz
Note 1:This requirement applies at a frequency offset equal or larger than 5 MHz from the upper edge of the channel bandwidth, whenever these frequencies overlap with the specified frequency band.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.20.

6.6.3.3.3.20 Minimum requirement (network signalled value “NS_25”)

When "NS_25" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.20-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.20-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	5 MHz, 10 MHz, 15 MHz, 20 MHz
Band 34	-40	MHz
Note 1:This requirement applies at a frequency offset equal or larger than 5 MHz from the upper edge of the channel bandwidth, whenever these frequencies overlap with the specified frequency band.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.21.

6.6.3.3.3.21 Minimum requirement (network signalled value “NS_27”)

When "NS_27" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.21-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.21-1: Additional requirements

Frequency band	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	5, 10, 15, 20 MHz
9 kHz f 3530 MHz	-40	1 MHz
3720 MHz f 5^th harmonic of the upper frequency edge of the UL operating band

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.23.

6.6.3.3.3.22 Minimum requirement (network signalled value “NS_28”)

When "NS_28" is indicated in the cell, the power of any UE emission for E-UTRA channels assigned within 5150-5350 MHz and 5470-5725 MHz shall not exceed the levels specified in Table 6.6.3.3.22-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

Table 6.6.3.3.22-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
Frequency band (MHz)	20 MHz	Measurement bandwidth
47 ≤ f ≤ 74	-54	100 kHz
87.5 ≤ f ≤ 118	-54	100 kHz
174 ≤ f ≤ 230	-54	100 kHz
470 ≤ f ≤ 862	-54	100 kHz
1000 ≤ f ≤ 5150	-30	1 MHz
5350 ≤ f ≤ 5470	-30	1 MHz
5725 ≤ f ≤ 26000	-30	1 MHz

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.24.

6.6.3.3.3.23 Minimum requirement (network signalled value “NS_29”)

When "NS_29" is indicated in the cell, the power of any UE emission for E-UTRA channels assigned within 5150-5350 and 5470-5725 MHz shall not exceed the levels specified in Table 6.6.3.3.3.25-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.23-1: Additional requirements

Centre Frequency Fc [MHz]	Protected range [MHz]	Frequency difference Δf between centre frequency – 5240 (for Fc=5180, 5200, 5220, 5240) 5260 (for Fc=5260, 5280, 5300, 5320) (MHz)	Minimum requirement [dBm]	Measurement bandwidth
5180, 5200, 5220, 5240	5135 ≤ f ≤ 5142	–	-26	1 MHz
	5142 < f ≤ 5150	–	-18
	5250 ≤ f < 5251	≥ 10 and < 11	10(10 – Δf)
	5251 ≤ f < 5260	≥ 11 and < 20	-10 – 8/9(Δf – 11)
	5260 ≤ f < 5266.7	≥ 20 and < 26.7	-18 – 1.2(Δf – 20)
	5266.7 ≤ f ≤ 5365	–	-26
5260, 5280, 5300, 5320	5135 ≤ f ≤ 5233.3	–	-26
	5233.3 < f ≤ 5240	≥ 20 and < 26.7	-18 – 1.2(Δf – 20)
	5240 < f ≤ 5249	≥ 11 and < 20	-10 – 8/9(Δf – 11)
	5249 < f ≤ 5250	≥ 10 and < 11	10(10 – Δf)
	5350 ≤ f ≤ 5365	–	-26
5500, 5520, 5540, 5560, 5580, 5600, 5620, 5640, 5660, 5680, 5700	5455 ≤ f ≤ 5460	–	-26
	5460 < f ≤ 5470	–	-19
	5725 ≤ f < 5740	–	-19
	5740 ≤ f ≤ 5745	–	-26

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.25.

6.6.3.3.3.24 Minimum requirement (network signalled value “NS_30”)

When "NS_30" is indicated in the cell, the power of any UE emission for E-UTRA channels assigned within 5150-5350 MHz, 5470-5725 MHz and 5725-5850 MHz shall not exceed the levels specified in Table 6.6.3.3.3.24-1, Table 6.6.3.3.3.24-2 and Table 6.6.3.3.3.26-3, respectively. These requirements also apply for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.24-1: Additional requirements for E-UTRA channels assigned within 5150-5350 MHz

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	20 MHz
4500 ≤ f ≤ 5150	-41	1 MHz
5350 ≤ f ≤ 5460	-41

Table 6.6.3.3.3.24-2: Additional requirements for E-UTRA channels assigned within 5470-5725 MHz

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
Frequency band (MHz)	20 MHz	Measurement bandwidth
4500 ≤ f ≤ 5150	-41	1 MHz
5350 ≤ f ≤ 5460	-41
5460 < f ≤ 5470	-27
5725 ≤ f	-27

Table 6.6.3.3.24-3: Additional requirements for E-UTRA channels assigned within 5725-5850 MHz

Frequency offset of measurement filter ‑3dB point, Δf	Frequency offset of measurement filter centre frequency, f_offset	Minimum requirement [dBm]	Measurement bandwidth
0 MHz ≤ Δf < 5 MHz	0.5 MHz ≤ f_offset < 5.5 MHz	27 – 2.28(f_offset/MHz – 0.5)	1 MHz
5 MHz ≤ Δf < 25 MHz	5.5 MHz ≤ f_offset < 25.5 MHz	15.6 – 0.28(f_offset/MHz – 0.5)	1 MHz
25 MHz ≤ Δf < 75 MHz	25.5 MHz ≤ f_offset < 75.5 MHz	10 – 0.74(f_offset/MHz – 0.5)	1 MHz
75 MHz ≤ Δf	75.5 MHz ≤ f_offset	-27	1 MHz
NOTE 1: The frequency offset f_offset is below and above the range 5725-5850 MHz; the measurement filter ‑3dB point is that closest to the range 5725-5850 MHz NOTE 2: The requirement applies when the offset of the measurement filter centre frequency is such that both -3 dB points of the measurement filter are confined within the frequency range 5725-5850 MHz.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.26.

6.6.3.3.3.25 Minimum requirement (network signalled value “NS_31”)

When "NS_31" is indicated in the cell, the power of any UE emission for E-UTRA channels assigned within 5150-5250 MHz, 5250-5350 MHz, 5470-5725 MHz and 5725-5850 MHz shall not exceed the levels specified in Table 6.6.3.3.3.25-1, Table 6.6.3.3.3.25-2, Table 6.6.3.3.3.25-3 and Table 6.6.3.3.3.25-4, respectively. These requirements also apply for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.25-1: Additional requirements for E-UTRA channels assigned within 5150-5250 MHz

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	20 MHz
f ≤ 5150	-27	1 MHz
f ≥ 5250	-27

Table 6.6.3.3.3.25-2: Additional requirements for E-UTRA channels assigned within 5250-5350 MHz

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	20 MHz
f ≤ 5250	-27	1 MHz
f ≥ 5350	-27

Table 6.6.3.3.25-3: Additional requirements for E-UTRA channels assigned within 5470-5725 MHz

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	20 MHz
f ≤ 5470	-27	1 MHz
f ≥ 5725	-27

Table 6.6.3.3.3.25-4: Additional requirements for E-UTRA channels assigned within 5725-5850 MHz

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	20 MHz
f ≤ 5725	-27	1 MHz
f ≥ 5850	-27

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.27.

6.6.3.3.3.26 Minimum requirement (network signalled value “NS_36”)

When "NS_36" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.26-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.26-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	5 MHz, 10 MHz and 15 MHz
470 ≤ f ≤ 694	-42	8MHz
NOTE: For a 5 MHz E-UTRA carrier confined within 698MHz and 703MHz, this requirement shall be met in normal conditions only. The requirement is relaxed to -30dBm in extreme conditions.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.28.

6.6.3.3.3.27 Minimum requirement (network signalled value “NS_38”)

When "NS_38" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.27-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.27-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz, 20 MHz
1400 ≤ f ≤ 1427	-32	27MHz
NOTE 1: This requirement shall be verified with UE transmission power of 15 dBm.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.29.

6.6.3.3.3.28 Minimum requirement (network signalled value “NS_39”)

When "NS_36" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.28-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.28-1: Additional requirements

Frequency band

(MHz)

Channel bandwidth /

Spectrum emission limit

(dBm)

Measurement bandwidth

1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz, 20 MHz

1475 ≤ f ≤ 1488

-28

1MHz

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.30.

6.6.3.3.3.29 Minimum requirement (network signalled value “NS_45”)

When "NS_45" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.29-1 & 6.6.3.3.29-2. These requirements also apply for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.29-1: Additional requirements for 1.4,3 and 5 MHz channel bandwidths

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
Frequency band (MHz)	1.4 MHz, 3 MHz, 5 MHz	Measurement bandwidth
0.009 < f ≤ 2477.5	-25	1 MHz
2477.5 < f ≤ 2478.5	-13	1 MHz
2478.5< f ≤ 2483.5	-10	1 MHz
2495 ≤ f < 2501	-13	1 MHz
2501 ≤ f ≤ 5^th harmonic of the upper frequency edge of the UL operating band	-25	1 MHz

Table 6.6.3.3.3.29-2: Additional requirements for 10 MHz channel bandwidths

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
Frequency band (MHz)	10 MHz	Measurement bandwidth
0.009 < f ≤ 2473.5	-25	1 MHz
2473.5 < f ≤ 2478.5	-13	1 MHz
2478.5< f ≤ 2483.5	-10	1 MHz
2495 ≤ f < 2505	-13	1 MHz
2505 ≤ f ≤ 5^th harmonic of the upper frequency edge of the UL operating band	-25	1 MHz

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.34.

6.6.3.3.3.30 Minimum requirement (network signalled value “NS_44”)

When "NS_44" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.30-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.30-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth	NOTE
Frequency band (MHz)	5, 10, 15, 20	Measurement bandwidth	NOTE
2620-2645	-15.5	5MHz	1
2645-2690	-40	1MHz	1
Note 1: The E-UTRA carrier with channel bandwidth is confined within 2570 MHz and 2615 MHz

6.6.3.3.3.31 Minimum requirement (network signalled value “NS_56”)

When "NS_56" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.3.31-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1-1 from the edge of the channel bandwidth.

Table 6.6.3.3.3.31-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit¹ (dBm)	Measurement bandwidth	NOTE
Frequency band (MHz)	5 MHz, 10MHz	Measurement bandwidth	NOTE
1541 ≤ f ≤ 1559	-102	2kHz	Averaged over any 2 millisecond active transmission interval
1559≤ f ≤ 1608	-85	700Hz
1608≤ f ≤ 1610	-85 +5/2 (f-1608)	700Hz
1610≤ f ≤ 1625	-80+ 66/15 (f-1610)	700Hz
1541 ≤ f ≤ 1608	-75	1MHz	Averaged over any 2 millisecond active transmission interval
1608≤ f ≤ 1610	-75 + 5/2 (f-1608)	1MHz
1610≤ f ≤ 1627.5	-70+ 57/17.5 (f-1610)	1MHz
1627.5	-37	4kHz
1638.5 ≤f ≤ 1645.5	-28	4kHz
1657.5 ≤f ≤ 1660.5	-28	4kHz
NOTE 1: The EIRP requirement in regulation is converted to conducted requirement using a 0 dBi antenna.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3.33.

6.6.3.3.4 Test description

6.6.3.3.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and channel bandwidths based on E-UTRA operating bands specified in table 5.4.2.1-1. All of these configurations shall be tested with applicable test parameters for each channel bandwidth, and are shown in Table 6.6.3.3.4.1-1 through Table 6.6.3.3.4.1-24. The details of the uplink reference measurement channels (RMCs) are specified in Annexes A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.3.4.1-1: Test Configuration Table (network signalled value "NS_04") (Power Class 2)

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range Additional test frequencies: For 5 MHz bandwidth: 2500.6 MHz, N_UL= 39696 For 10 MHz bandwidth: 2504.1 MHz, N_UL= 39731 For 15 MHz bandwidth: 2510.9 MHz, N_UL= 39799 For 20 MHz bandwidth: 2517.6 MHz, N_UL= 39866
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_04 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation TDD	Mod’n	RB allocation TDD	RB_start TDD
1 (Note 1)	5MHz	N/A for A-MPR testing		QPSK	1	0
2 (Note 1)	5MHz			QPSK	16	9
3 (Note 2)	5MHz			QPSK	25	0
4 (Note 1)	5MHz			16QAM	16	9
5 (Note 2)	5MHz			16QAM	25	0
6 (Note 1)	10MHz			QPSK	1	0
7 (Note 1)	10MHz			QPSK	1	49
8 (Note 1)	10MHz			QPSK	24	0
9 (Note 1)	10MHz			QPSK	40	10
10	10MHz			QPSK	50	0
11	10MHz			16QAM	50 (Note 3)	0
12 (Note 1)	15MHz			QPSK	1	0
13 (Note 1)	15MHz			QPSK	1	74
14 (Note 1)	15MHz			QPSK	32	0
15 (Note 1)	15MHz			QPSK	60	15
16	15MHz			QPSK	75	0
17	15MHz			16QAM	75 (Note 3)	0
18 (Note 1)	20MHz			QPSK	1	0
19 (Note 1)	20MHz			QPSK	1	99
20 (Note 1)	20MHz			QPSK	36	0
21 (Note 1)	20MHz			QPSK	75	25
22	20MHz			QPSK	100	0
23	20MHz			16QAM	100 (Note 3)	0
Note 1: Only applicable for Low Range. Note 2: Only applicable for additional test frequencies. Note 3: Applies only for UE-Categories ≥2.

Table 6.6.3.3.4.1-2: Test Configuration Table (network signalled value "NS_04") (Power Class 3)

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low range, Mid range, High range Additional test frequencies for Rel-12 to Rel-13 and bit 2 of modifiedMPRbehavior = 0: For 5 MHz bandwidth: 2499.6 MHz, N_UL= 39696 For 10 MHz bandwidth: 2504.1 MHz, N_UL= 39731 For 15 MHz bandwidth: 2510.9 MHz, N_UL= 39799 For 20 MHz bandwidth: 2517.6 MHz, N_UL= 39866 Additional test frequencies for Rel-12 and later and bit 2 of modifiedMPRbehavior = 1: For 5 MHz bandwidth: 2500.6 MHz, N_UL= 39686 For 10 MHz bandwidth: 2504.1 MHz, N_UL= 39731 For 15 MHz bandwidth: 2510.9 MHz, N_UL= 39799 For 20 MHz bandwidth: 2517.6 MHz, N_UL= 39866
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10 MHz, 15 MHz, 20MHz
Test Parameters for NS_04 A-MPR
		Downlink Configuration		Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation TDD	Mod’n	RB allocation TDD	RB_start TDD
1 (Note 6)	5MHz	N/A for A-MPR testing		QPSK	25	0
2 (Note 6)	5MHz			QPSK	8	Note 3
3(Note 6)	5MHz			QPSK	6	Note 3
4 (Note 6)	5MHz			16QAM (Note 5)	25	0
5 (Note 6)	5MHz			16QAM (Note 5)	8	Note 3
6 (Note 6)	10MHz			QPSK	1	0
7 (Note 6)	10MHz			QPSK	12	0
8 (Note 6)	10MHz			QPSK	50	0
9 Note 6)	10MHz			16QAM (Note 5)	50 (Note 4)	0
10 (Note 6)	10MHz			QPSK	24	13
11 (Note 6)	10MHz			16QAM (Note 5)	24	13
12 (Note 6)	10MHz			QPSK	36	13
13 (Note 6)	10MHz			QPSK	12	37
14 (Note 6)	10MHz			QPSK	1	49
15 (Note 6)	15MHz			QPSK	1	0
16 (Note 6)	15MHz			QPSK	16	0
17 (Note 6)	15MHz			QPSK	75	0
18 (Note 6)	15MHz			16QAM (Note 5)	75 (Note 4)	0
19 (Note 6)	15MHz			QPSK	36	19
20 (Note 6)	15MHz			16QAM (Note 5)	36 (Note 4)	19
21 (Note 6)	15MHz			QPSK	50	19
22 (Note 6)	15MHz			QPSK	18	56
23 (Note 6)	15MHz			QPSK	1	74
24 (Note 6)	20MHz			QPSK	1	0
25 (Note 6)	20MHz			QPSK	18	0
26 (Note 6)	20MHz			QPSK	100	0
27 (Note 6)	20MHz			16QAM (Note 5)	100 (Note 4)	0
28 (Note 6)	20MHz			QPSK	50	25
29 (Note 6)	20MHz			16QAM (Note 5)	50 (Note 4)	25
30 (Note 6)	20MHz			QPSK	75	25
31 (Note 6)	20MHz			QPSK	25	75
32 (Note 6)	20MHz			QPSK	1	99
33 (Note 8)	5MHz			QPSK	1	0
34 (Note 8)	5MHz			QPSK	16	9
35 (Note 9)	5MHz			QPSK	25	0
36 (Note 8)	5MHz			16QAM (Note 5)	16	9
37 (Note 9)	5MHz			16QAM (Note 5)	25	0
38 (Note 8)	10MHz			QPSK	1	0
39 (Note 8)	10MHz			QPSK	1	49
40 (Note 8)	10MHz			QPSK	24	0
41 (Note 8)	10MHz			QPSK	40	10
42 (Note 7)	10MHz			QPSK	50	0
43 (Note 7)	10MHz			16QAM (Note 5)	50 (Note 4)	0
44 (Note 8)	15MHz			QPSK	1	0
45 (Note 8)	15MHz			QPSK	1	74
46 (Note 8)	15MHz			QPSK	32	0
47 (Note 8)	15MHz			QPSK	60	15
48 (Note 7)	15MHz			QPSK	75	0
49 (Note 7)	15MHz			16QAM (Note 5)	75 (Note 4)	0
50 (Note 8)	20MHz			QPSK	1	0
51 (Note 8)	20MHz			QPSK	1	99
52 (Note 8)	20MHz			QPSK	36	0
53 (Note 8)	20MHz			QPSK	75	25
54 (Note 7)	20MHz			QPSK	100	0
55 (Note 7)	20MHz			16QAM (Note 5)	100 (Note 4)	0
Note 1: Test Channel Bandwidths are checked separately for E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The configuration ID will be used to map the applicable Test Configuration to be corresponding Test Requirement in subclause 6.2.4 as not all combinations are necessarily required based on the applicability of the UE. Note 3: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 4: Applies only for UE-Categories ≥2. Note 5: The 16QAM configurations shall not apply to UEs which support UL 64QAM. Note 6: Applies only for Rel-11 and earlier. Note 7: Applies only for Rel-12 and later. Note 8: Applies only for Rel-12 and later and Low Range. Note 9: Applies only for Rel-12 and later and Mid, High Range and additional test frequencies.

Table 6.6.3.3.4.1-3: Test Configuration Table (network signalled value "NS_05")

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1			Normal
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1			Low range, Mid range In case of Low range: – For 5MHz Channel Bandwidth: 1927.2MHz (N_UL = 18072) – For 10MHz Channel Bandwidth: 1934.7MHz (N_UL = 18147) – For 15MHz Channel Bandwidth: 1932.5MHz (N_UL = 18125) – For 20MHz Channel Bandwidth: 1930MHz (N_UL = 18100)
Test Channel Bandwidths as specified in TS 36.508 [7] subclause 4.3.1			5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
	Downlink Configuration			Uplink Configuration
Ch BW	Mod’n	RB allocation		Mod’n	RB allocation		RB_start
		FDD	TDD		FDD	TDD	FDD
5MHz	N/A for Additional Spurious Emissions testing			QPSK	1	N/A	0
5MHz				QPSK	1		24
5MHz				QPSK	25		0
10MHz				QPSK	1		0
10MHz				QPSK	1		49
10MHz				QPSK	12		0
10MHz				QPSK	12		38
10MHz				QPSK	48		0
10MHz				QPSK	48		2
10MHz (Note 7)				QPSK	50		0
10MHz (Note 7)				16QAM (Note 6)	50 (Note 3)		0
15MHz (Note 8)				QPSK	1		8
15MHz (Note 8)				QPSK	1		66
15MHz (Note 8)				QPSK	16		8
15MHz (Note 8)				QPSK	16		51
15MHz (Note 8)				QPSK	30		8
15MHz (Note 8)				QPSK	30		37
20MHz (Note 8)				QPSK	1		24
20MHz (Note 8)				QPSK	1		75
20MHz (Note 8)				QPSK	18		24
20MHz (Note 8)				QPSK	18		58
20MHz (Note 8)				QPSK	24		24
20MHz (Note 8)				QPSK	24		52
15MHz (Note 9)				QPSK	1		0
15MHz (Note 9)				QPSK	1		74
15MHz (Note 9)				QPSK	16		0
15MHz (Note 9)				QPSK	16		59
15MHz (Note 9)				QPSK	48		0
15MHz (Note 9)				QPSK	48		27
15MHz (Note 9)				QPSK	75		0
15MHz (Note 9)				16QAM (Note 6)	75 (Note 3)		0
20MHz (Note 9)				QPSK	1		0
20MHz (Note 9)				QPSK	1		99
20MHz (Note 9)				QPSK	18		0
20MHz (Note 9)				QPSK	18		82
20MHz (Note 9)				QPSK	48		0
20MHz (Note 9)				QPSK	48		52
20MHz (Note 9)				QPSK	100		0
20MHz (Note 9)				16QAM (Note 6)	100 (Note 3)		0
10MHz (Note 10)				QPSK	50		0
10MHz (Note 10)				16QAM (Note 6)	50 (Note 3)		0
15MHz (Note 10)				QPSK	1		0
15MHz (Note 10)				QPSK	75		0
15MHz (Note 10)				QPSK	16		8
15MHz (Note 10)				QPSK	30		8
15MHz (Note 10)				QPSK	54		8
15MHz (Note 10)				QPSK	64		8
15MHz (Note 10)				QPSK	1		74
15MHz (Note 10)				QPSK	6		69
15MHz (Note 10)				QPSK	8		67
20MHz (Note 10)				QPSK	1		0
20MHz (Note 10)				QPSK	100		0
20MHz (Note 10)				QPSK	18		24
20MHz (Note 10)				QPSK	24		24
20MHz (Note 10)				QPSK	40		24
20MHz (Note 10)				QPSK	50		24
20MHz (Note 10)				QPSK	72		24
20MHz (Note 10)				QPSK	1		99
20MHz (Note 10)				QPSK	6		94
20MHz (Note 10)				QPSK	24		76
10MHz (Note 11)				QPSK	50		0
10MHz (Note 11)				16QAM (Note 6)	50 (Note 3)		0
15MHz (Note 11)				QPSK	1		0
15MHz (Note 11)				QPSK	1		74
15MHz (Note 11)	QPSK	16	0
15MHz (Note 11)	QPSK	16	59
15MHz (Note 11)	QPSK	48	0
15MHz (Note 11)	QPSK	48	27
15MHz (Note 11)	QPSK	75	0
15MHz (Note 11)	16QAM (Note 6)	75 (Note 3)	0
20MHz (Note 11)	QPSK	1	0
20MHz (Note 11)	QPSK	1	99
20MHz (Note 11)	QPSK	18	0
20MHz (Note 11)	QPSK	18	82
20MHz (Note 11)	QPSK	48	0
20MHz (Note 11)	QPSK	48	52
20MHz (Note 11)	QPSK	100	0
20MHz (Note 11)	16QAM (Note 6)	100 (Note 3)	0
Note 1: Void Note 2: Void Note 3: Applies only for UE-Categories ≥2. Note 4: Void. Note 5: Void. Note 6: The 16QAM configurations shall not apply to UEs which support UL 64QAM. Note 7: Applies for ID 1 & 2 from table 6.6.3.3.5.2-0 for Band1 and not available for Band65. Note 8: Applies for low range and for ID 1 & 2 from table 6.6.3.3.5.2-0 for Band1 and not available for Band65. Note 9: Applies for mid range and for ID 1 & 2 from table 6.6.3.3.5.2-0 for Band1 and not available for Band65. Note 10: Applies only for low range and for ID 3 & 4 from table 6.6.3.3.5.2-0 for Band1 and low range for Band65. Note 11: Applies only for mid range and for ID 3 & 4 from table 6.6.3.3.5.2-0 for Band1 and mid range for Band65. Note 12: ModifiedMPRbehavior is defined in annex J.1

Table 6.6.3.3.4.1-4: Test Configuration Table (network signalled value "NS_07")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1)				Mid range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				10MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Test Number	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation	RB_start
1	10MHz	N/A for Additional Spurious Emissions testing.		QPSK	1	0
2	10MHz			QPSK	8	0
3	10MHz			QPSK	6	13
4	10MHz			QPSK	20	13
5	10MHz			QPSK	12	13
6	10MHz			16QAM (Note 2)	36 (Note 1)	13
7	10MHz			QPSK	16	19
8	10MHz			QPSK	12	19
9	10MHz			16QAM (Note 2)	16	19
10	10MHz			QPSK	30	19
11	10MHz			16QAM (Note 2)	30 (Note 1)	19
12	10MHz			QPSK	6	43
13	10MHz			QPSK	2	48
14	10MHz			QPSK	50	0
15	10MHz			QPSK	12	0
16	10MHz			16QAM (Note 2)	50 (Note 1)	0
Note 1: Applies only for UE-Categories ≥2. Note 2: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-5: Test Configuration Table (network signalled value "NS_08")

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1			Normal
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1			High range
Test Channel Bandwidths as specified in TS 36.508 [7] subclause 4.3.1			5MHz, 10MHz, 15MHz
Test Parameters for Channel Bandwidths
	Downlink Configuration			Uplink Configuration
Ch BW	Mod’n	RB allocation		Mod’n	RB allocation
		FDD	TDD		FDD	TDD
5MHz	N/A for Additional Spurious Emissions testing			QPSK	1	N/A
5MHz				QPSK	8
5MHz				QPSK	25
10MHz				QPSK	1
10MHz				QPSK	12
10MHz				QPSK	40
10MHz				QPSK	50
10MHz				16QAM (Note 4)	50 (Note 3)
15MHz				QPSK	1
15MHz				QPSK	16
15MHz				QPSK	40
15MHz				QPSK	75
15MHz				16QAM (Note 4)	75 (Note 3)
Note 1: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 2: The RB_start of partial RB allocation shall be RB#0 and RB# (max + 1 – RB allocation) of the channel bandwidth Note 3: Applies only for UE-Categories ≥2. Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-6: Test Configuration Table (network signalled value "NS_09")

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1			Normal
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1			High range
Test Channel Bandwidths as specified in TS 36.508 [7] subclause 4.3.1			5MHz, 10MHz, 15MHz
Test Parameters for Channel Bandwidths
	Downlink Configuration			Uplink Configuration
Ch BW	Mod’n	RB allocation		Mod’n	RB allocation
		FDD	TDD		FDD	TDD
5MHz	N/A for Additional Spurious Emissions testing			QPSK	1	N/A
5MHz				QPSK	8
5MHz				QPSK	25
10MHz				QPSK	1
10MHz				QPSK	12
10MHz				QPSK	40
10MHz				QPSK	50
10MHz				16QAM (Note 4)	50 (Note 3)
15MHz				QPSK	1
15MHz				QPSK	16
15MHz				QPSK	40
15MHz				QPSK	54
15MHz				QPSK	75
15MHz				16QAM (Note 4)	75 (Note 3)
Note 1: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 2: The RB_start of partial RB allocation shall be RB#0 and RB# (max + 1 – RB allocation) of the channel bandwidth Note 3: Applies only for UE-Categories ≥2. Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-7: Test Configuration Table (network signalled value "NS_11")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
				Normal
Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1)				For 3 MHz Channel Bandwidth: a. 2001.5 MHz (N_UL= 25515) b. 2004.5 MHz (N_UL = 25545) For 5 MHz Channel Bandwidth a. 2002.5 MHz (N_UL = 25525) b. 2004.5 MHz (N_UL = 25545) c. 2007.5 MHz (N_UL = 25575) For 10 MHz Channel Bandwidth a. 2005 MHz (N_UL = 25550) b. 2005.5 MHz (N_UL = 25555) c. 2015 MHz (N_UL = 25650) For 15 MHz Channel Bandwidth a. 2007.5 MHz (N_UL = 25575) b. 2012.5 MHz (N_UL = 25625) For 20 MHz Channel Bandwidth a. 2010 MHz (N_UL = 25600)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				3MHz, 5MHz, 10MHz, 15MHz, 20MHz
				3MHz, 5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_11 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	3MHz	N/A for A-MPR testing		QPSK	6
2	3MHz			QPSK	15
3	3MHz			16QAM (Note 4)	6
4	3MHz			16QAM (Note 4)	15
5	5MHz			QPSK	1
6	5MHz			QPSK	8
7	5MHz			QPSK	25
8	5MHz			16QAM (Note 4)	8
9	5MHz			16QAM (Note 4)	25
10	10MHz			QPSK	1
11	10MHz			QPSK	12
12	10MHz			QPSK	50
13	10MHz			16QAM (Note 4)	12
14	10MHz			16QAM (Note 4)	50
14	10MHz			16QAM (Note 4)	(Note 3)
15	15MHz			QPSK	1
16	15MHz			QPSK	8
17	15MHz			QPSK	25
18	15MHz			QPSK	30
19	15MHz			QPSK	75
20	15MHz			16QAM (Note 4)	8
21	15MHz			16QAM (Note 4)	25
22	15MHz			16QAM (Note 4)	30
23	15MHz			16QAM (Note 4)	75
24	20MHz			QPSK	1
25	20MHz			QPSK	10
26	20MHz			QPSK	25
27	20MHz			QPSK	100
28	20MHz			16QAM (Note 4)	10
29	20MHz			16QAM (Note 4)	25
30	20MHz			16QAM (Note 4)	100
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 3: Applies only for UE-Categories ≥2. Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-8: Test Configuration Table (network signalled value "NS_12")

Initial Conditions
Test Environment				NC
(as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies				For 1.4 MHz Channel Bandwidth: UL 814.9 MHz (NUL = 26699) For 3 MHz Channel Bandwidth: UL 815.7 MHz (NUL = 26707) For 5 MHz Channel Bandwidth: UL 816.7 MHz (NUL = 26717) For 10 MHz Channel Bandwidth: UL 819.2 MHz (NUL = 26742) For 15 MHz Channel Bandwidth: UL 821.7 MHz (NUL = 26767)
(as specified in TS36.508 [7] subclause 4.3.1)
Test Channel Bandwidths				1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz
(as specified in TS 36.508 [7] subclause 4.3.1)				1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Test Number	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	1.4 MHz	N/A for Additional Spurious Emissions testing		QPSK	1	0
2	1.4 MHz			QPSK	6	0
3	1.4 MHz			QPSK	1	1
4	1.4 MHz			QPSK	5	1
5	1.4 MHz			16QAM (Note 3)	6	0
6 (Note 1)	3 MHz			QPSK	4	0
7 (Note 1)	3 MHz			QPSK	10	0
8	3 MHz			QPSK	4	4
9	3 MHz			QPSK	10	4
10 (Note 1)	3 MHz			16QAM (Note 3)	15	0
11	5 MHz			QPSK	8	0
12	5 MHz			QPSK	15	0
13	5 MHz			QPSK	8	7
14 (Note 1)	5 MHz			QPSK	15	7
15	5 MHz			16QAM (Note 3)	25	0
16 (Note 2)	10 MHz			QPSK	18	0
17 (Note 2)	10 MHz			QPSK	18	16
18 (Note 2)	10 MHz			16QAM (Note 4, 3)	50	0
19 (Note 2)	15 MHz			QPSK	30	0
20 (Note 2)	15 MHz			QPSK	30	31
21 (Note 2)	15 MHz			16QAM (Note 4, 3)	75	0
Note 1: Only for UEs of Rel-11 and earlier. Note 2: Only for UEs of Rel-12 and later. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM. Note 4 : Applies only for UE-Categories ≥2.

Table 6.6.3.3.4.1-9: Test Configuration Table (network signalled value "NS_13")

Initial Conditions
Test Environment				NC
(as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies				For 1.4 MHz Channel Bandwidth: UL 819.7 MHz (NUL = 26747) For 3 MHz Channel Bandwidth: UL 820.5 MHz (NUL = 26755) For 5 MHz Channel Bandwidth: UL 821.5 MHz (NUL = 26765)
(as specified in TS36.508 [7] subclause 4.3.1)
Test Channel Bandwidths				1.4 MHz, 3MHz and 5 MHz
(as specified in TS 36.508 [7] subclause 4.3.1)				1.4 MHz, 3MHz and 5 MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Test Number	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1 (Note 1)	1.4 MHz	N/A for Additional Spurious Emissions testing		QPSK	6	0
2 (Note 1)	3 MHz			QPSK	15	0
3	5 MHz			QPSK	1	0
4	5 MHz			QPSK	25	0
5	5 MHz			QPSK	15	0
6	5 MHz			QPSK	15	7
7	5 MHz			16QAM (Note 2)	25	0
Note 1: Only for UEs of Rel-12 and later Note 2: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-10: Test Configuration Table (network signalled value "NS_14")

Initial Conditions
Test Environment				NC
(as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies				For 10 MHz Channel Bandwidth: UL 829 MHz (N_UL = 26840) For 15 MHz Channel Bandwidth: Mid range
(as specified in TS36.508 [7] subclause 4.3.1)
Test Channel Bandwidths				10 MHz, 15 MHz
(as specified in TS 36.508 [7] subclause 4.3.1)				10 MHz, 15 MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Test Number	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	10 MHz	N/A for Additional Spurious Emissions testing		QPSK	1	0
2	10 MHz			QPSK	25	0
3	10 MHz			QPSK	50	0
4	10 MHz			QPSK	25	1
5 (Note 1)	10 MHz			16QAM (Note 2)	50	0
6	15 MHz			QPSK	8	0
7	15 MHz			QPSK	25	0
8	15 MHz			QPSK	75	0
9	15 MHz			QPSK	50	15
10 (Note 1)	15 MHz			16QAM (Note 2)	75	0
Note 1: Applies only for UE-Categories ≥2. Note 2: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-11: Test Configuration Table (network signalled value "NS_15")

Initial Conditions

Test Environment

(as specified in TS 36.508 [7] subclause 4.1)

Test Frequencies

(as specified in TS36.508 [7] subclause 4.3.1)

For 1.4 MHz Channel Bandwidth: High range

For 3 MHz Channel Bandwidth: UL 843.5 MHz (N_UL = 26985) or High range

For 5 MHz Channel Bandwidth: UL 842.5 MHz (N_UL = 26975) or High range

For 10 MHz Channel Bandwidth: UL 840 MHz (NUL = 26950) or High range

For 15 MHz Channel Bandwidth: UL 837.5 MHz (NUL = 26925) or High range

Test Channel Bandwidths

(as specified in TS 36.508 [7] subclause 4.3.1)

1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz

Test Parameters for Channel Bandwidths

Downlink Configuration

Uplink Configuration

Configuration ID

Ch BW

Mod’n

RB allocation

Mod’n

RB allocation FDD

RBstart FDD

1 (note 3)

1.4 MHz

N/A for Additional Spurious Emissions testing

QPSK

2 (note 3)

1.4 MHz

16QAM

(Note 4)

3 (note 3)

3 MHz

QPSK

4 (note 3)

3 MHz

QPSK

5 (note 3)

3 MHz

16QAM

(Note 4)

6 (note 2)

3 MHz

QPSK

7 (note 3)

5 MHz

QPSK

8 (note 3)

5 MHz

QPSK

9 (note 3)

5 MHz

16QAM

(Note 4)

10 (note 2)

5 MHz

QPSK

11 (note 2)

5 MHz

QPSK

12 (note 3)

10 MHz

QPSK

13 (note 3)

10 MHz

QPSK

14 (note 3)

10 MHz

QPSK

15 (note 3)

10 MHz

QPSK

16 (note 3)

10 MHz

QPSK

17 (note 3)

10 MHz

QPSK

18 (note 1, 3)

10 MHz

16QAM

(Note 4)

19 (note 2)

10 MHz

QPSK

20 (note 2)

10 MHz

QPSK

21 (note 3)

15 MHz

QPSK

22 (note 3)

15 MHz

QPSK

23 (note 3)

15 MHz

QPSK

24 (note 1, 3)

15 MHz

16QAM

(Note 4)

25 (note 2)

15 MHz

QPSK

26 (note 2)

15 MHz

QPSK

Note 1: Applies only for UE-Categories ≥2.

Note 2: Applicable only test frequency < high range

Note 3: Applicable only to high range frequency testing.

Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-12: Test Configuration Table (network signalled value "NS_16")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1)				For 1.4 MHz Channel Bandwidth: Low range For 3 MHz Channel Bandwidth: Low range, 810 MHz (N_UL= 27070) For 5 MHz Channel Bandwidth: Low range, 811 MHz (N_UL= 27080) , 814.5 MHz (N_UL= 27115) For 10 MHz Channel Bandwidth: Low range, 813.5 MHz (N_UL= 27105), 817 MHz (N_UL= 27140)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				1.4 MHz, 3 MHz, 5 MHz, 10 MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	1.4 MHz	N/A for Additional Spurious Emissions testing.		QPSK	1	0
2	1.4 MHz			QPSK	6	0
3 (Note 1)	1.4 MHz			16QAM (Note 4)	6	0
4	3 MHz			QPSK	1	0
5	3 MHz			QPSK	12	1
6	3 MHz			QPSK	15	0
7 (Note 1)	3 MHz			16QAM (Note 4)	15	0
8	5 MHz			QPSK	1	0
9	5 MHz			QPSK	12	2
10	5 MHz			QPSK	18	2
11	5 MHz			QPSK	20	0
12	5 MHz			QPSK	20	2
13	5 MHz			QPSK	25	0
14 (Note 1)	5 MHz			16QAM (Note 4)	25	0
15	10 MHz			QPSK	1	0
16 (Note 2)	10 MHz			QPSK	1	10
17 (Note 2)	10 MHz			QPSK	20	0
18 (Note 2)	10 MHz			QPSK	27	15
19 (Note 2)	10 MHz			QPSK	32	15
20	10 MHz			QPSK	32	0
21	10 MHz			QPSK	50	0
22 (Note 1)	10 MHz			16QAM (Note 4)	50	0
23 (Note 3)	10 MHz			QPSK	40	0
24 (Note 3)	10 MHz			QPSK	40	1
Note 1: Applies only for UE-Categories ≥2. Note 2: Applies only for 10 MHz channel for Low Range, and 813.5 MHz. Note 3: Applies only for 10 MHz channel for 817 MHz range. Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-13: Test Configuration Table (network signalled value "NS_17")

Initial Conditions
Test Environment (as specified in TS 36.508[7] subclause 4.1)				Normal
Test Frequencies (as specified inTS36.508 [7] subclause 4.3.1)				Mid range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for Additional Spurious Emissions testing		QPSK	1
2	5MHz			QPSK	8
3	5MHz			QPSK	25
4	5MHz			16QAM (Note 4)	25
					(Note 3)
5	10MHz			QPSK	1
6	10MHz			QPSK	12
7	10MHz			QPSK	50
8	10MHz			16QAM (Note 4)	50
					(Note 3)
Note 1: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 2: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 3: Applies only for UE-Categories ≥2. Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-14: Test Configuration Table (network signalled value "NS_18")

Initial Conditions
Test Environment (as specified in TS 36.508[7] subclause 4.1)				Normal
Test Frequencies (as specified inTS36.508 [7] subclause 4.3.1)				Low range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for Additional Spurious Emissions testing		QPSK	1
2	5MHz			QPSK	8
3	5MHz			QPSK	25
4	5MHz			16QAM (Note 2)	25 (Note 3)
5	10MHz			QPSK	1
6	10MHz			QPSK	12
7	10MHz			QPSK	50
8	10MHz			16QAM (Note 2)	50 (Note 3)
9	15MHz			QPSK	1
10	15MHz			QPSK	16
11	15MHz			QPSK	75
12	15MHz			16QAM (Note 2)	75 (Note 3)
13	20MHz			QPSK	1
14	20MHz			QPSK	18
15	20MHz			QPSK	100
16	20MHz			16QAM (Note 2)	100 (Note 3)
Note 1: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 2: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 3: Applies only for UE-Categories ≥2. Note 2: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-15: Test Configuration Table (network signalled value "NS_19")

Initial Conditions
Test Environment (as specified in TS 36.508[7] subclause 4.1)				Normal
Test Frequencies (as specified inTS36.508 [7] subclause 4.3.1)				Low range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				3MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation TDD
1	3MHz	N/A		QPSK	15
2	3MHz			16QAM (Note 4)	15 (Note 3)
3	10MHz			QPSK	40
4	10MHz			16QAM (Note 4)	40 (Note 3)
5	15MHz			QPSK	1
6	15MHz			QPSK	18
7	15MHz			QPSK	36
8	15MHz			QPSK	45
9	15MHz			16QAM (Note 4)	45 (Note 3)
10	20MHz			QPSK	1
11	20MHz			QPSK	40
12	20MHz			QPSK	45
13	20MHz			QPSK	50
14	20MHz			16QAM (Note 4)	50 (Note 3)
Note 1: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 2: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 3: Applies only for UE-Categories ≥2. Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-16: Test Configuration Table (network signalled value "NS_20")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
				Normal
Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1)				For 5 MHz Channel Bandwidth a. 2002.5 MHz (N_UL = 25525) b. 2007.5 MHz (N_UL = 25575) c. 2012.5 MHz (N_UL = 25625) d. 2017.5 MHz (N_UL = 25675) For 10 MHz Channel Bandwidth a. 2005 MHz (N_UL = 25550) b. 2015 MHz (N_UL = 25650) For 15 MHz Channel Bandwidth a. 2012.5 MHz (N_UL = 25625) For 20 MHz Channel Bandwidth a. 2010 MHz (N_UL = 25600)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_20 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for A-MPR testing		QPSK	8
2	5MHz			QPSK	15
3	5MHz			QPSK	25
4	5MHz			16QAM (Note 4)	15
5	5MHz			16QAM (Note 4)	25
6	10MHz			QPSK	8
7	10MHz			QPSK	12
8	10MHz			QPSK	50
9	10MHz			16QAM (Note 4)	12
10	10MHz			16QAM (Note 4)	50
10	10MHz			16QAM (Note 4)	(Note 3)
11	15MHz			QPSK	6
12	15MHz			QPSK	25
13	15MHz			QPSK	36
14	15MHz			QPSK	75
15	15MHz			16QAM (Note 4)	25
16	15MHz			16QAM (Note 4)	36
17	15MHz			16QAM (Note 4)	75
18	20MHz			QPSK	8
19	20MHz			QPSK	18
20	20MHz			QPSK	25
21	20MHz			QPSK	75
22	20MHz			QPSK	100
23	20MHz			16QAM (Note 4)	18
24	20MHz			16QAM (Note 4)	25
25	20MHz			16QAM (Note 4)	75
26	20MHz			16QAM (Note 4)	100
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 3: Applies only for UE-Categories ≥2. Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-17: Test Configuration Table (network signalled value "NS_21")

Initial Conditions

Test Environment

(as specified in TS 36.508 [7] subclause 4.1)

Test Frequencies

(as specified in TS36.508 [7] subclause 4.3.1)

Low range or High range

Test Channel Bandwidths

(as specified in TS 36.508 [7] subclause 4.3.1)

5 MHz, 10 MHz

Test Parameters for Channel Bandwidths

Downlink Configuration

Uplink Configuration

Configuration ID

Ch BW

Mod’n

RB allocation

Mod’n

RB allocation FDD

RBstart FDD

1 (note 2)

5 MHz

QPSK

2 (note 2)

5 MHz

QPSK

3 (note 2)

10 MHz

QPSK

4 (note 3)

10 MHz

QPSK

5 (note 2)

10 MHz

QPSK

6 (note 3)

10 MHz

QPSK

7 (note 3)

10 MHz

QPSK

8 (note 1, 3)

10 MHz

16QAM

(Note 4)

Note 1: Applies only for UE-Categories ≥2.

Note 2: Applicable only to low range frequency testing.

Note 3: Applicable only to high range frequency testing.

Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-18: Test Configuration Table (network signalled value "NS_22")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range, Mid Range, High Range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_22 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation TDD	RB_start TDD
1	5MHz	N/A for A-MPR testing		QPSK	1	0
2	5MHz			QPSK	25	0
3	5MHz			QPSK	1	24
4	5MHz			16QAM	1	0
5	5MHz			16QAM	1	24
6	10MHz			QPSK	50	0
7	10MHz			QPSK	36	0
8	10MHz			QPSK	1	0
9	10MHz			QPSK	1	49
10	10MHz			16QAM	1	0
11	10MHz			16QAM	1	49
12	15MHz			QPSK	75	0
13	15MHz			QPSK	50	0
14	15MHz			QPSK	1	0
15	15MHz			QPSK	1	74
16	15MHz			16QAM	1	0
17	15MHz			16QAM	1	74
18	20MHz			QPSK	100	0
19	20MHz			QPSK	64	0
20	20MHz			QPSK	1	0
21	20MHz			QPSK	1	99
22	20MHz			16QAM	1	0
23	20MHz			16QAM	1	99
Note 1: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-19: Test Configuration Table (network signalled value "NS_23")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range, Mid Range, High Range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_23 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation TDD	RB_start TDD
1	5MHz	N/A for A-MPR testing		QPSK	1	0
2	5MHz			QPSK	1	24
3	5MHz			QPSK	25	0
4	5MHz			16QAM	1	0
5	5MHz			16QAM	1	24
6	10MHz			QPSK	50	0
7	15MHz			QPSK	75	0
8	20MHz			QPSK	100	0
Note 1: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-20: Test Configuration Table (network signalled value "NS_24")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 1985 MHz (N_UL = 131722) 2007.5 MHz (N_UL= high range) 10 MHz CH BW: 1980 MHz (N_UL = 131672) 1990 MHz (N_UL = 131772) 2005 MHz (N_UL= high range) 15 MHZ CH BW: 1980 MHz (N_UL = 131672) 1990 MHz (N_UL = 131772) 2002.5 MHz (N_UL= high range) 20 MHz CH BW: 2000 MHz (N_UL= high range)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_24 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	2007.5	5MHz	N/A for A-MPR testing		QPSK	1	0
2	2007.5	5MHz			QPSK	8	17
3	2007.5	5MHz			QPSK	25	0
4 (Notes 2,3)	2007.5	5MHz			16QAM	25	0
5	1985	5MHz			QPSK	8	17
6	1980	10MHz			QPSK	12	1
7 (Notes 2,3)	1980	10MHz			16QAM	50	0
8	1980	10MHz			QPSK	48	2
9	1980	10MHz			QPSK	25	25
10	1980	10MHz			QPSK	1	49
11	1980	10MHz			QPSK	12	38
12 (Notes 2,3)	1980	10MHz			16QAM	12	38
13	1980	10MHz			QPSK	3	47
14	1980	10MHz			QPSK	8	1
15	1990	10MHz			QPSK	1	0
16	1990	10MHz			QPSK	12	38
17 (Notes 2,3)	1990	10MHz			16QAM	50	0
18	2005	10MHz			QPSK	12	38
19	2005	10MHz			QPSK	50	0
20 (Notes 2,3)	2005	10MHz			16QAM	50	0
21	1980	15MHz			QPSK	1	11
22	1980	15MHz			QPSK	16	11
23	1980	15MHz			QPSK	45	11
24 (Notes 2,3)	1980	15MHz			16QAM	50	0
25	1980	15MHz			QPSK	16	28
26	1980	15MHz			QPSK	16	59
27	1980	15MHz			QPSK	60	15
28	1980	15MHz			QPSK	30	12
29	2002.5	15MHz			QPSK	1	0
30	2002.5	15MHz			QPSK	16	59
31 (Notes 2,3)	2002.5	15MHz			16QAM	16	59
32 (Notes 2,3)	2002.5	15MHz			16QAM	75	0
33	2000	20MHz			QPSK	1	0
34	2000	20MHz			QPSK	18	82
35 (Notes 2,3)	2000	20MHz			16QAM	18	82
36 (Notes 2,3)	2000	20MHz			16QAM	100	0
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-21: Test Configuration Table (network signalled value "NS_25")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 2007.5 MHz (N_UL= high range) 10 MHz CH BW: 1980 MHz (N_UL = 131672) 1990 MHz (N_UL = 131772) 2005 MHz (N_UL= high range) 15 MHZ CH BW: 1980 MHz (N_UL = 132672) 1990 MHz (N_UL = 131772) 2002.5 MHz (N_UL= high range) 20 MHz CH BW: 2000 MHz (N_UL= high range)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_25 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	2007.5	5MHz	N/A for A-MPR testing		QPSK	25	0
2 (Notes 2,3)	2007.5	5MHz			16QAM	25	0
3	2007.5	5MHz			QPSK	8	9
4	2007.5	5MHz			QPSK	1	24
5	2007.5	5MHz			QPSK	8	17
6 (Notes 2,3)	2007.5	5MHz			16QAM	8	17
7	1980	10MHz			QPSK	12	1
8 (Notes 2,3)	1980	10MHz			16QAM	50	0
9 (Notes 2,3)	1980	10MHz			16QAM	48	2
10	1980	10MHz			QPSK	25	25
11	1980	10MHz			QPSK	1	49
12	1980	10MHz			QPSK	12	38
13	1990	10MHz			QPSK	12	0
14	1990	10MHz			QPSK	25	0
15	1990	10MHz			QPSK	50	0
16 (Notes 2,3)	1990	10MHz			16QAM	25	0
17	1990	10MHz			QPSK	48	2
18	1990	10MHz			QPSK	30	19
19 (Notes 2,3)	1990	10MHz			16QAM	30	19
20	1990	10MHz			QPSK	12	31
21	2005	10MHz			QPSK	1	0
22	2005	10MHz			QPSK	12	6
23	2005	10MHz			QPSK	50	0
24 (Notes 2,3)	2005	10MHz			16QAM	50	0
25	2005	10MHz			QPSK	40	10
26 (Notes 2,3)	2005	10MHz			16QAM	40	10
27	2005	10MHz			QPSK	32	18
28 (Notes 2,3)	2005	10MHz			16QAM	32	18
29	2005	10MHz			QPSK	12	23
30	1980	15MHz			QPSK	16	4
31	1980	15MHz			QPSK	75	0
32	1980	15MHz			QPSK	60	15
33 (Notes 2,3)	1980	15MHz			16QAM	40	35
34	1980	15MHz			QPSK	1	74
35	1980	15MHz			QPSK	12	63
36	1980	15MHz			QPSK	16	55
37	2002.5	15MHz			QPSK	1	0
38	2002.5	15MHz			QPSK	16	0
39 (Notes 2,3)	2002.5	15MHz			16QAM	16	0
40 (Notes 2,3)	2002.5	15MHz			16QAM	1	0
41	1980	20MHz			QPSK	1	0
42	1980	20MHz			QPSK	18	0
43 (Notes 2,3)	1980	20MHz			16QAM	100	0
44	1980	20MHz			QPSK	64	36
45	1980	20MHz			QPSK	18	72
46 (Notes 2,3)	1980	20MHz			16QAM	54	46
47	1980	20MHz			QPSK	18	55
48	2000	20MHz			QPSK	1	0
49	2000	20MHz			QPSK	18	72
50 (Notes 2,3)	2000	20MHz			16QAM	18	72
51 (Notes 2,3)	2000	20MHz			16QAM	100	0
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-22: Test Configuration Table (network signalled value "NS_27")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to Frequency columnin test parameters
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_27 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	Frequency	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	Low/Mid	5MHz	N/A for A-MPR testing		QPSK	1	0
2	High	5MHz			QPSK	1	24
3	Low/Mid/High	5MHz			QPSK	25	0
4	Low/Mid/High	5MHz			16QAM	25	0
5	Low/Mid	10MHz			QPSK	1	0
6	High	10MHz			QPSK	1	49
7	Low/Mid/High	10MHz			QPSK	50	0
8 (Note 2)	Low/Mid/High	10MHz			16QAM	50	0
9	Low/Mid	15MHz			QPSK	1	0
10	Low	15MHz			QPSK	1	7
11	Low/Mid	15MHz			QPSK	16	0
12	High	15MHz			QPSK	1	74
13	High	15MHz			QPSK	1	67
14	High	15MHz			QPSK	16	74
15	Low/Mid/High	15MHz			QPSK	75	0
16 (Note 2)	Low/Mid/High	15MHz			16QAM	75	0
17	Low/Mid	20MHz			QPSK	1	0
18	Low	20MHz			QPSK	1	13
19	Low	20MHz			QPSK	1	16
20	Low/Mid	20MHz			QPSK	21	0
21	High	20MHz			QPSK	1	99
22	High	20MHz			QPSK	1	86
23	High	20MHz			QPSK	1	83
24	High	20MHz			QPSK	21	0
25	Low/Mid/High	20MHz			QPSK	100	0
26 (Note 2)	Low/Mid/High	20MHz			16QAM	100	0
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-23: Test Configuration Table (network signalled value "NS_36")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 700.5 MHz (N_UL = low range) 705.5 MHz (N_UL=132747) 10 MHz CH BW: 703 MHz (N_UL = low range) 708 MHz (N_UL = 132772) 15 MHz CH BW: 705.5 MHz (N_UL = low range) 710.5 MHz (N_UL =132797 )
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz
Test Parameters for NS_36 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	700.5	5MHz	N/A for A-MPR testing		QPSK	1	0
2	700.5	5MHz			QPSK	25	0
3	700.5	5MHz			QPSK	20	1
4	700.5	5MHz			QPSK	24	1
5	700.5	5MHz			QPSK	12	0
6 (Notes 2,3)	700.5	5MHz			16QAM	12	0
7	705.5	5MHz			QPSK	25	0
8 (Notes 2,3)	705.5	5MHz			16QAM	25	0
9	703	10MHz			QPSK	50	0
10	703	10MHz			QPSK	1	0
11	703	10MHz			QPSK	40	9
12	703	10MHz			QPSK	36	13
13	703	10MHz			QPSK	10	40
14	703	10MHz			QPSK	6	44
15	708	10MHz			QPSK	50	0
16 (Notes 2,3)	708	10MHz			16QAM	50	0
17	705.5	15MHz			QPSK	75	0
18	705.5	15MHz			QPSK	50	17
19	705.5	15MHz			QPSK	50	24
20	705.5	15MHz			QPSK	1	57
21	705.5	15MHz			QPSK	10	17
22	705.5	15MHz			QPSK	18	24
23 (Notes 2,3)	705.5	15MHz			16QAM	18	24
24	710.5	15MHz			QPSK	75	0
25	710.5	15MHz			16QAM	75	0
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-24: Test Configuration Table (network signalled value "NS_45")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range, Mid Range, High Range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				1.4MHz, 3MHz, 5MHz, 10MHz
Test Parameters for NS_45 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation TDD	RB_start TDD
1	1.4MHz	N/A for A-MPR testing		QPSK	1	0
2	1.4MHz			QPSK	6	0
3	1.4MHz			16QAM	6	5
4	3MHz			QPSK	1	0
5	3MHz			QPSK	15	0
6	3MHz			16QAM	1	14
7	5MHz			QPSK	1	0
8	5MHz			QPSK	25	0
9	5MHz			QPSK	1	24
10	5MHz			16QAM	1	0
11	5MHz			16QAM	1	24
12	10MHz			QPSK	50	0
13	10MHz			QPSK	36	0
14	10MHz			QPSK	1	0
15	10MHz			QPSK	1	49
16	10MHz			16QAM	1	0
17	10MHz			16QAM	1	49
Note 1: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.6.3.3.4.1-25: Test Configuration Table (network signalled value "NS_44")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Low Range, Mid Range Additional test frequencies: For 5 MHz bandwidth: 2612.5 MHz, N_UL= 38175 For 10 MHz bandwidth: 2610 MHz, N_UL= 38150 For 15 MHz bandwidth: 2607.5 MHz, N_UL= 38125 For 20 MHz bandwidth: 2605 MHz, N_UL= 38100
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_44 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	Frequency	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	Note 1	5MHz	N/A for A-MPR testing		QPSK	1	24
2	Note 1	5MHz			QPSK	25	0
3	Note 1	5MHz			16QAM	1	24
4	Note 1	5MHz			16QAM	25	0
5	Note 1	10MHz			QPSK	1	49
6	Note 1	10MHz			QPSK	45	5
7	Low/Mid	10MHz			QPSK	50	0
8	Note 1	10MHz			16QAM	1	49
9	Note 1	10MHz			16QAM	45	5
10	Low/Mid	10MHz			16QAM	50	0
11	Note 1	15MHz			QPSK	75	0
12	Note 1	15MHz			QPSK	45	30
13	Note 1	15MHz			QPSK	1	74
14	Low/Mid	15MHz			QPSK	75	0
15	Note 1	15MHz			16QAM	75	0
16	Note 1	15MHz			16QAM	45	30
17	Note 1	15MHz			16QAM	1	74
18	Low/Mid	15MHz			16QAM	75	0
19	Mid/Note 1	20MHz			QPSK	100	0
20	Mid/Note 1	20MHz			QPSK	45	55
21	Mid/Note 1	20MHz			QPSK	1	99
22	Low	20MHz			QPSK	100	0
23	Mid/Note 1	20MHz			16QAM	100	0
24	Mid/Note 1	20MHz			16QAM	45	55
25	Mid/Note 1	20MHz			16QAM	1	99
26	Low	20MHz			16QAM	100	0
Note 1: Only applicable for additional test frequencies.

Table 6.6.3.3.4.1-26: Test Configuration Table (network signalled value "NS_56")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 1630 MHz (low range) 10 MHz CH BW: 1632.5 MHz (low range)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz
Test Parameters for NS_56 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	1630	5MHz	N/A for A-MPR testing		QPSK	1	0
2	1630	5MHz			QPSK	25	0
3 (Notes 2,3)	1630	5MHz			16QAM	25	0
4	1632.5	10MHz			QPSK	1	0
5	1632.5	10MHz			QPSK	12	0
6	1632.5	10MHz			QPSK	50	0
7 (Notes 2,3)	1632.5	10MHz			16QAM	50	0
8	1632.5	10MHz			QPSK	1	6
9	1632.5	10MHz			QPSK	1	35
10	1632.5	10MHz			QPSK	1	40
11	1632.5	10MHz			QPSK	1	49
12	1632.5	10MHz			QPSK	15	35
13	1632.5	10MHz			QPSK	10	40
14 (Notes 2,3)	1632.5	10MHz			16QAM	10	40
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.6.3.3.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Editor’s note: The following lines belong at the end of section 6.2.4.4.1. As new tables are added to this section, these lines should always follow the tables.

1. Connect the SS to the UE to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure A.7.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals are initially set up according to Annex C0, C.1 and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Table 6.6.3.3.4.1-1to Table 6.6.3.3.4.1-24 depending on network signal value.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.3.4.3.

6.6.3.3.4.2 Test procedure

1. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 6.6.3.3.4.1-1 to 6.6.3.3.4.1-28. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

2. Send continuously uplink power control "up" commands in the uplink scheduling information to the UE until the UE transmits at P_UMAX level.

3. Measure the mean power of the UE in the channel bandwidth of the radio access mode according to the test configuration, which shall meet the requirements described in Tables 6.2.4.5-1 to 6.2.4.5‑27 for Power Class 3 UEs or 6.2.4_1.5-2 for Power Class 2 UEs as appropriate. The period of the measurement shall be at least one sub-frame (1ms).

4. Measure the power of the transmitted signal with a measurement filter of bandwidths according to Table 6.6.3.3.5.1-1 to 6.6.3.3.5.21-1 as appropriate. The centre frequency of the filter shall be stepped in contiguous steps according to the same table. For NS_07 measurements made in a bandwidth of 6.25kHz, measurement parameter settings defined in table 6.6.3.3.4.2-1 shall be used. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

Table 6.6.3.3.4.2-1: Measurement setup for NS_07

	Option 1: Measurement with No RMS VBW available	Option2 Measurement with VBW Filtering on Power scale
VBW	>=62.5 kHz (10 times or more the RBW)	<=43Hz
RBW	<=6.25kHz	<=6.25kHz
Detector type	Averages signal envelope during each measurement point, such as "RMS detector"	Peak
Averaging mode (Trace averaging)	Power (RMS voltage)	Power (RMS voltage), as controlled by "Average Type"
Average Type (applies to detector)	Power (RMS voltage) (automatically occurs with "RMS detector")	Not applicable
Average Type (applies to VBW filter)	Not applicable	Power (RMS voltage)
Number of averages	30, to reduce variance as required, or use an even longer sweep time	1 or use an even narrower VBW filter, thus a longer sweep time
Sweep time	[Don’t specify]	Sweep rate (span divided by sweep time) <= 0.8 * RBW*VBW

6.6.3.3.4.3 Message contents

6.6.3.3.4.3.1 Message contents exceptions (network signalled value "NS_04")

1. Information element additionalSpectrumEmission is set to NS_04. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.1-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_04" for Power Class 2

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	4 (NS_04)

6.6.3.3.4.3.2 Message contents (network signalled value "NS_05")

Message contents are according to TS 36.508 [7] subclause 4.6, with the following exceptions:

1. Information element additionalSpectrumEmission is set to NS_05. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.2-1: SystemInformationBlockType2: Additional spurious emissions requirement

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	5 (NS_05)

6.6.3.3.4.3.3 Message contents (network signalled value "NS_07")

Message contents are according to TS 36.508 [7] subclause 4.6, with the following exceptions:

1. Information element additionalSpectrumEmission is set to NS_07. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.3-1: SystemInformationBlockType2: Additional spurious emissions requirement

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	7 (NS_07)

6.6.3.3.4.3.4 Message contents (network signalled value "NS_08")

Message contents are according to TS 36.508 [7] subclause 4.6, with the following exceptions:

1. Information element additionalSpectrumEmission is set to NS_08. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.4-1: SystemInformationBlockType2: Additional spurious emissions requirement

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	8 (NS_08)

6.6.3.3.4.3.5 Message contents (network signalled value "NS_09")

Message contents are according to TS 36.508 [7] subclause 4.6, with the following exceptions:

1. Information element additionalSpectrumEmission is set to NS_09. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.5-1: SystemInformationBlockType2: Additional spurious emissions requirement

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	9 (NS_09)

6.6.3.3.4.3.6 Message contents exceptions (network signalled value "NS_11")

1. Information element additionalSpectrumEmission is set to NS_11. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.6-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_11"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	11 (NS_11)

6.6.3.3.4.3.7 Message contents exceptions (network signalled value "NS_12")

1. Information element additionalSpectrumEmission is set to NS_12. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.7-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_12"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	12 (NS_12)

6.6.3.3.4.3.8 Message contents exceptions (network signalled value "NS_13")

1. Information element additionalSpectrumEmission is set to NS_13. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.8-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_13"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	13 (NS_13)

6.6.3.3.4.3.9 Message contents exceptions (network signalled value "NS_14")

1. Information element additionalSpectrumEmission is set to NS_14. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.9-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_14"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	14 (NS_14)

6.6.3.3.4.3.10 Message contents exceptions (network signalled value "NS_15")

1. Information element additionalSpectrumEmission is set to NS_15. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.10-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_15"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	15 (NS_15)

6.6.3.3.4.3.11 Message contents exceptions (network signalled value "NS_16")

1. Information element additionalSpectrumEmission is set to NS_16. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.11-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_16"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	16 (NS_16)

6.6.3.3.4.3.12 Message contents exceptions (network signalled value "NS_17")

1. Information element additionalSpectrumEmission is set to NS_17. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.12-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_17"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	17 (NS_17)

6.6.3.3.4.3.13 Message contents exceptions (network signalled value "NS_18")

1. Information element additionalSpectrumEmission is set to NS_18. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.13-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_18"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	18 (NS_18)

6.6.3.3.4.3.14 Message contents exceptions (network signalled value "NS_19")

1. Information element additionalSpectrumEmission is set to NS_19. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.14-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_19"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	19 (NS_19)

6.6.3.3.4.3.15 Message contents exceptions (network signalled value "NS_20")

1. Information element additionalSpectrumEmission is set to NS_20. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.15-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_20"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	20 (NS_20)

6.6.3.3.4.3.16 Message contents exceptions (network signalled value "NS_21")

1. Information element additionalSpectrumEmission is set to NS_21. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.16-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_21"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	21 (NS_21)

6.6.3.3.4.3.17 Message contents exceptions (network signalled value "NS_22")

1. Information element additionalSpectrumEmission is set to NS_22. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.17-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_22"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	22(NS_23)

6.6.3.3.4.3.18 Message contents exceptions (network signalled value "NS_23")

1. Information element additionalSpectrumEmission is set to NS_23. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.18-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_23"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	23(NS_23)

6.6.3.3.4.3.19 Message contents exceptions (network signalled value "NS_24")

1. Information element additionalSpectrumEmission is set to NS_24. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.19-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_24"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	24 (NS_24)

6.6.3.3.4.3.20 Message contents exceptions (network signalled value "NS_25")

1. Information element additionalSpectrumEmission is set to NS_25. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.20-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_25"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	25 (NS_25)

6.6.3.3.4.3.21 Message contents exceptions (network signalled value "NS_27")

1. Information element additionalSpectrumEmission is set to NS_27. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.21-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_27"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	27(NS_27)

6.6.3.3.4.3.22 Message contents exceptions (network signalled value "NS_36")

1. Information element additionalSpectrumEmission is set to NS_36. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.22-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_36”

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	32
additionalSpectrumEmission-v10l0	36 (NS_36)

6.6.3.3.4.3.23 Message contents exceptions (network signalled value "NS_38")

1. Information element additionalSpectrumEmission is set to NS_38. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.23-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_38”

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	32
additionalSpectrumEmission-v10l0	38 (NS_38)

6.6.3.3.4.3.24 Message contents exceptions (network signalled value "NS_39")

1. Information element additionalSpectrumEmission is set to NS_39. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.24-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_39”

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	32
additionalSpectrumEmission-v10l0	39 (NS_39)

6.6.3.3.4.3.25 Message contents exceptions (network signalled value "NS_45")

1. Information element additionalSpectrumEmission is set to NS_45. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.25-1: SystemInformationBlockType2: Additional spurious emissions requirement

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	45 (NS_45)

6.6.3.3.4.3.26 Message contents exceptions (network signalled value "NS_44")

1. Information element additionalSpectrumEmission is set to NS_44. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.26-1: SystemInformationBlockType2: Additional spurious emissions requirement

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	44 (NS_44)

6.6.3.3.4.3.27 Message contents exceptions (network signalled value "NS_56")

1. Information element additionalSpectrumEmission is set to NS_56. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3.4.3.27-1: SystemInformationBlockType2: Additional spurious emissions requirement

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	56 (NS_56)

6.6.3.3.5 Test requirement

This clause specifies the requirements for the specified E-UTRA band for an additional spectrum emission requirement with protected bands as indicated from table 6.6.3.3.5.1-1 to table 6.6.3.3.5.25-2.

6.6.3.3.5.1 Test requirement (network signalled value “NS_04”)

When "NS 04" is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-3 or 6.2.4_1.5-2 as appropriate, and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.1-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.1-1: Additional requirements

Frequency band	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
Frequency band	5, 10, 15, 20 MHz	Measurement bandwidth
2490.5 MHz ≤ f < 2495 MHz	-13	1 MHz
9 kHz < f < 2490.5 MHz	-25	1 MHz

6.6.3.3.5.2 Test requirement (network signalled value "NS_05")

When "NS_05" is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-4 as appropriate,

and

the measured average power of spurious emission, derived in step 2, shall not exceed the described requirements for the corresponding Release as defined in Table 6.6.3.3.5.2-0. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.2-0: Applicable requirements per UE release

UE Release

Rel-10 and earlier

Rel-11

(number 1 bit in modifiedMPRbehavior=0)

Rel-11

(number 1 bit in modifiedMPRbehavior=1)

Rel-12 and later

Applicable Requirements

Table 6.6.3.3.5.2-1

6.6.3.3.5.2-2

Table 6.6.3.3.5.2-1

6.6.3.3.5.2-2

Table 6.6.3.3.5.2-3

Table 6.6.3.3.5.2-1: Additional test requirements (PHS) (Rel-11 and earlier)

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)				Measurement bandwidth
Frequency band (MHz)	5 MHz	10 MHz	15 MHz	20 MHz	Measurement bandwidth
1884.5 f 1915.7^*1	-41	-41	-41	-41	300 KHz
Note 1: Applicable when the lower edge of the assigned E-UTRA UL channel bandwidth frequency is larger than or equal to the upper edge of PHS band (1915.7 MHz) + 4 MHz + the Channel BW assigned, where Channel BW is as defined in sub-clause 5.4.2. Additional restrictions apply for operations below this point.

The requirements in Table 6.6.3.3.5.2-1 apply with the additional restrictions specified in Table 6.6.3.3.5.2-2 when the lower edge of the assigned E-UTRA UL channel bandwidth frequency is less than the upper edge of PHS band (1915.7 MHz) + 4 MHz + the channel BW assigned.

Table 6.6.3.3.5.2-2: RB restrictions for additional requirement (PHS)

15 MHz channel bandwidth with f_c = 1932.5 MHz
RB_start	0-7	8-66	67-74
L_CRB	N/A	≤ MIN(30, 67 – RB_start)	N/A
20 MHz channel bandwidth with f_c = 1930 MHz
RB_start	0-23	24-75	76-99
L_CRB	N/A	≤ MIN(24, 76 – RB_start)	N/A

Table 6.6.3.3.5.2-3: Additional test requirements (PHS) (Rel-12 and onwards)

Frequency band

(MHz)

Channel bandwidth / Spectrum emission limit (dBm)

Measurement bandwidth

MHz

1884.5 f 1915.7

-41

300 KHz

6.6.3.3.5.3 Test requirement (network signalled value "NS_07")

When "NS_07" is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-7 as appropriate,

and

– the measured average power of spurious emission, derived in step 4, shall not exceed the described value in Table 6.6.3.3.5.3-1. These requirements also apply for the frequency ranges that are less than Δf_OOB(MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.3-1: Additional requirements (network signalled value "NS_07")

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	10 MHz
769 ≤ f ≤ 775	-55.5	6.25 kHz
Note: The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB

6.6.3.3.5.4 Test requirement (network signalled value "NS_08")

When "NS_08" is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-8 as appropriate,

and

the measured average power of spurious emission, derived in step 4, shall not exceed the described value in Table 6.6.3.3.5.4-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.4-1: Additional requirements (network signalled value "NS_08")

Frequency band

(MHz)

Channel bandwidth / Spectrum emission limit (dBm)

Measurement bandwidth

5MHz

10MHz

15MHz

860 ≤ f ≤ 895

-40

1 MHz

6.6.3.3.5.5 Test requirement (network signalled value "NS_09")

When "NS_09" is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-9 as appropriate,

and

– the measured average power of spurious emission, derived in step 4, shall not exceed the described value in table 6.6.3.3.5.5-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.5-1: Additional requirements (network signalled value "NS_09")

Frequency band

(MHz)

Channel bandwidth / Spectrum emission limit (dBm)

Measurement bandwidth

5MHz

10MHz

15MHz

1475.9 ≤ f ≤ 1510.9

-35

1 MHz

NOTE 1: To improve measurement accuracy, A-MPR values for NS_09 specified in Table 6.2.4.3-1 in sub-clause 6.2.4 are derived based on 100 kHz RBW.

6.6.3.3.5.6 Test requirement (network signalled value "NS_11")

When "NS 11" is indicated in the cell:

the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-11 as appropriate,

and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.6-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.6-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth	Note
Frequency band (MHz)	1.4, 3, 5, 10, 15, 20 MHz	Measurement bandwidth	Note
E-UTRA Band 2	-50	1 MHz
1998 ≤ f ≤ 1999	-21	1 MHz
1997 ≤ f < 1998	-27	1 MHz
1996 ≤ f < 1997	-32	1 MHz
1995 ≤ f < 1996	-37	1 MHz
1990 ≤ f < 1995	-40	1 MHz

6.6.3.3.5.7 Test requirement (network signalled value "NS_12")

When "NS 12" is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-12 as appropriate,

and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.7-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.7-1: Additional requirements

Frequency band (MHz)	Channel bandwidth/ Spectrum emission limit (dBm)	Measurement bandwidth
	1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz
806 ≤ f ≤ 813.5	-42	6.25 kHz
NOTE 1: The requirement applies for E-UTRA carriers with lower channel edge at or above 814.2 MHz. NOTE 2: The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB.

6.6.3.3.5.8 Test requirement (network signalled value "NS_13")

When "NS 13" is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-13 as appropriate,

and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.8-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.8-1: Additional requirements

Frequency band (MHz)	Channel bandwidth/ Spectrum emission limit (dBm)	Measurement bandwidth
	1.4, 3, 5 MHz
806 ≤ f ≤ 816	-42	6.25 kHz
NOTE 1: The requirement applies for E-UTRA carriers with lower channel edge at or above 819 MHz. NOTE 2: The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB.

6.6.3.3.5.9 Test requirement (network signalled value "NS_14")

When "NS 14" is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-14 as appropriate,

and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.9-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.9-1: Additional requirements

Frequency band (MHz)	Channel bandwidth/ Spectrum emission limit (dBm)	Measurement bandwidth
	10 MHz, 15 MHz
806 ≤ f ≤ 816	-42	6.25 kHz
NOTE 1: The requirement applies for E-UTRA carriers with lower channel edge at or above 824 MHz. NOTE 2: The emissions measurement shall be sufficiently power averaged to ensure a standard deviation < 0.5 dB.

6.6.3.3.5.10 Test requirement (network signalled value "NS_15")

When "NS 15" is indicated in the cell:

the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-15 as appropriate,

and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.10-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.10-1: Additional requirements

Frequency band

(MHz)

Channel bandwidth / Spectrum emission limit (dBm)

Measurement bandwidth

Note

1.4, 3, 5, 10, 15 MHz

851 ≤ f ≤ 859

-53

6.25 kHz

6.6.3.3.5.11 Test requirement (network signalled value "NS_16")

When "NS 16" is indicated in the cell:

the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-16 as appropriate,

and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.11-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.11-1: Additional requirements

Frequency band

(MHz)

Channel bandwidth / Spectrum emission limit (dBm)

Measurement bandwidth

Note

1.4, 3, 5, 10 MHz

790 ≤ f ≤ 803

-32

1 MHz

6.6.3.3.5.12 Test requirement (network signalled value "NS_17")

When "NS 17" is indicated in the cell:

the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-17 as appropriate,

and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.12-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.12-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth	Note
	5, 10 MHz
470 ≤ f ≤ 710	-26.2	6 MHz	1
Note 1: Applicable when the assigned E-UTRA carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz.

6.6.3.3.5.13 Test requirement (network signalled value "NS_18")

When "NS 18" is indicated in the cell:

the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-18 as appropriate,

and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.13-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.13-1: Additional requirements

Frequency band

(MHz)

Channel bandwidth / Spectrum emission limit (dBm)

Measurement bandwidth

Note

5, 10, 15, 20 MHz

692 ≤ f ≤ 698

-26.2

6 MHz

6.6.3.3.5.14 Test requirement (network signalled value "NS_19")

When "NS 19" is indicated in the cell:

the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-19 as appropriate,

and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.14-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.14-1: Additional requirements

Frequency band

(MHz)

Channel bandwidth / Spectrum emission limit (dBm)

Measurement bandwidth

Note

3, 5, 10, 15, 20 MHz

662 ≤ f ≤ 694

-25

8 MHz

6.6.3.3.5.15 Test requirement (network signalled value "NS_20")

When "NS 20" is indicated in the cell:

the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-20 as appropriate,

and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.15-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.15-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth	Note
Frequency band (MHz)	5, 10, 15, 20 MHz	Measurement bandwidth	Note
1990 ≤ f < 1999	-40	1 MHz
1999 ≤ f ≤ 2000	-40	Note 1
Note 1: The measurement bandwidth is 1% of the applicable E-UTRA channel bandwidth (5.4.2.1-1).

6.6.3.3.5.16 Test requirement (network signalled value “NS_21”)

When “NS_21” is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-21 as appropriate, and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.16-1. These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.16-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
Frequency band (MHz)	5, 10 MHz	Measurement bandwidth
2200 ≤ f < 2288	-40	1 MHz
2288 ≤ f < 2292	-37	1 MHz
2292 ≤ f < 2296	-31	1 MHz
2296 ≤ f < 2300	-25	1 MHz
2320 ≤ f < 2324	-25	1 MHz
2324 ≤ f < 2328	-31	1 MHz
2328 ≤ f < 2332	-37	1 MHz
2332 ≤ f ≤ 2395	-40	1 MHz

6.6.3.3.5.17 Test requirement (network signalled value “NS_22”)

When "NS 22" is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-22 as appropriate, and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.17-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.17-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	MBW
	5, 10, 15, 20 MHz
3400 ≤ f ≤ 3800	-23 (NOTE 1, NOTE 3)	5 MHz
	-40 (NOTE 2)	1 MHz
NOTE 1: This requirement applies within an offset between 5 MHz and 25 MHz from the lower and from the upper edge of the channel bandwidth, whenever these frequencies overlap with the specified frequency band. NOTE 2: This requirement applies from 3400 MHz to 25 MHz below the lower E-UTRA channel edge and from 25 MHz above the upper E-UTRA channel edge to 3800 MHz. NOTE 3: This emission limit might imply risk of harmful interference to UE(s) operating in the protected operating band

6.6.3.3.5.18 Test requirement (network signalled value “NS_23”)

When "NS 23" is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-23 as appropriate, and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.18-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.18-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	MBW
	5, 10, 15, 20 MHz
3400 ≤ f ≤ 3800	-23 (NOTE 1, NOTE 4)	5 MHz
	-40 (NOTE 2)	1 MHz
NOTE 1: This requirement applies within an offset between 5 MHz + F_{offset_NS_23} and 25 MHz + F_{offset_NS_23} from the lower and from the upper edges of the channel bandwidth, whenever these frequencies overlap with the specified frequency band. NOTE 2: This requirement applies from 3400 MHz to 25 MHz + F_{offset_NS_23} below the lower E-UTRA channel edge and from 25 MHz + Foffset_{_NS_23} above the upper E-UTRA channel edge to 3800 MHz. NOTE 3: F_{offset_NS_23} is: 0 MHz for 5 MHz channel BW, 5 MHz for 10 MHz channel BW, 9 MHz for 15 MHz channel BW and 12 MHz for 20 MHz channel BW. NOTE 4: This emission limit might imply risk of harmful interference to UE(s) operating in the protected operating band.

6.6.3.3.5.19 Test requirement (network signalled value “NS_24”)

When "NS 24" is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-24 as appropriate, and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.19-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.19-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	5 MHz, 10 MHz, 15 MHz, 20 MHz
Band 34	-50	MHz
Note 1:This requirement applies at a frequency offset equal or larger than 5 MHz from the upper edge of the channel bandwidth, whenever these frequencies overlap with the specified frequency band.

6.6.3.3.5.20 Test requirement (network signalled value “NS_25”)

When "NS 25" is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-25 as appropriate, and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.20-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.20-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	5 MHz, 10 MHz, 15 MHz, 20 MHz
Band 34	-40	MHz
Note 1:This requirement applies at a frequency offset equal or larger than 5 MHz from the upper edge of the channel bandwidth, whenever these frequencies overlap with the specified frequency band.

6.6.3.3.5.21 Test requirement (network signalled value “NS_27”)

When "NS 27" is indicated in the cell:

the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-27 as appropriate,

and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.21-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.21-1: Additional requirements

Frequency band	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
Frequency band	5, 10, 15, 20 MHz	Measurement bandwidth
9 kHz f 3530 MHz	-40	1 MHz

6.6.3.3.5.22 Test requirement (network signalled value “NS_36”)

When "NS 36" is indicated in the cell:

the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-29 as appropriate,

and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.22-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.22-1: Additional requirements

Frequency band

(MHz)

Channel bandwidth /

Spectrum emission limit

(dBm)

Measurement bandwidth

5 MHz, 10 MHz and 15 MHz

470 ≤ f ≤ 694

-42

8MHz

6.6.3.3.5.23 Test requirement (network signalled value “NS_38”)

When "NS 38" is indicated in the cell:

the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-29 as appropriate,

and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.23-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.23-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
	1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz, 20 MHz
1400 ≤ f ≤ 1427	-32	27MHz
NOTE 1: This requirement shall be verified with UE transmission power of 15 dBm.

6.6.3.3.5.24 Test requirement (network signalled value “NS_39”)

When "NS 39" is indicated in the cell:

the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4.5-29 as appropriate,

and

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.24-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.24-1: Additional requirements

Frequency band

(MHz)

Channel bandwidth /

Spectrum emission limit

(dBm)

Measurement bandwidth

1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz, 20 MHz

1475 ≤ f ≤ 1488

-28

1MHz

6.6.3.3.5.25 Test requirement (network signalled value “NS_45”)

When "NS 45" is indicated in the cell:

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.25-1 & Table 6.6.3.3.5.25-2. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.25-1: Additional requirements

Table 6.6.3.3.5.25-1: Additional requirements for 1.4,3 and 5 MHz channel bandwidths

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
Frequency band (MHz)	1.4 MHz, 3 MHz, 5 MHz	Measurement bandwidth
0.009 < f ≤ 2477.5	-25	1 MHz
2477.5 < f ≤ 2478.5	-13	1 MHz
2478.5< f ≤ 2483.5	-10	1 MHz
2495 ≤ f < 2501	-13	1 MHz
2501 ≤ f ≤ 5^th harmonic of the upper frequency edge of the UL operating band	-25	1 MHz

Table 6.6.3.3.5.25-2: Additional requirements for 10 MHz channel bandwidths

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth
Frequency band (MHz)	10 MHz	Measurement bandwidth
0.009 < f ≤ 2473.5	-25	1 MHz
2473.5 < f ≤ 2478.5	-13	1 MHz
2478.5< f ≤ 2483.5	-10	1 MHz
2495 ≤ f < 2505	-13	1 MHz
2505 ≤ f ≤ 5^th harmonic of the upper frequency edge of the UL operating band	-25	1 MHz

6.6.3.3.5.26 Test requirement (network signalled value “NS_44”)

When "NS 44" is indicated in the cell:

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.26-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.26-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit (dBm)	Measurement bandwidth	NOTE
Frequency band (MHz)	5, 10, 15, 20	Measurement bandwidth	NOTE
2620-2645	-15.5	5MHz	1
2645-2690	-40	1MHz	1
Note 1: The E-UTRA carrier with channel bandwidth is confined within 2570 MHz and 2615 MHz.

6.6.3.3.5.27 Test requirement (network signalled value “NS_56”)

When "NS 56" is indicated in the cell:

– the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3.5.27-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3.5.27-1: Additional requirements

Frequency band (MHz)	Channel bandwidth / Spectrum emission limit¹ (dBm)	Measurement bandwidth	NOTE
Frequency band (MHz)	5 MHz, 10MHz	Measurement bandwidth	NOTE
1541 ≤ f ≤ 1559	-102	2kHz	Averaged over any 2 millisecond active transmission interval
1559≤ f ≤ 1608	-85	700Hz
1608≤ f ≤ 1610	-85 +5/2 (f-1608)	700Hz
1610≤ f ≤ 1625	-80+ 66/15 (f-1610)	700Hz
1541 ≤ f ≤ 1608	-75	1MHz	Averaged over any 2 millisecond active transmission interval
1608≤ f ≤ 1610	-75 + 5/2 (f-1608)	1MHz
1610≤ f ≤ 1627.5	-70+ 57/17.5 (f-1610)	1MHz
1627.5	-37	4kHz
1638.5 ≤f ≤ 1645.5	-28	4kHz
1657.5 ≤f ≤ 1660.5	-28	4kHz
NOTE 1: The EIRP requirement in regulation is converted to conducted requirement using a 0 dBi antenna.

6.6.3.3_1 Additional spurious emissions for UL 64QAM

6.6.3.3_1.1 Test purpose

Same test purpose as in clause 6.6.3.3.1.

6.6.3.3_1.2 Test applicability

This test case applies to all types of E-UTRA UE from release 13 and forward that support UL 64QAM.

6.6.3.3_1.3 Minimum conformance requirements

Same minimum conformance requirements as in clause 6.6.3.3.3.

6.6.3.3_1.4 Test description

6.6.3.3_1.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and channel bandwidths based on E-UTRA operating bands specified in table 5.4.2.1-1. All of these configurations shall be tested with applicable test parameters for each channel bandwidth, and are shown in Table 6.6.3.3_1.4.1-1 through Table 6.6.3.3_1.4.1-21. The details of the uplink reference measurement channels (RMCs) are specified in Annexes A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.3_1.4.1-1: Test Configuration Table (network signalled value "NS_04")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range, Mid Range, High Range Additional test frequencies for Rel-12 to Rel-13 and bit 2 of modifiedMPRbehavior = 0: For 5 MHz bandwidth: 2499.6 MHz, N_UL= 39696 For 10 MHz bandwidth: 2504.1 MHz, N_UL= 39731 For 15 MHz bandwidth: 2510.9 MHz, N_UL= 39799 For 20 MHz bandwidth: 2517.6 MHz, N_UL= 39866 Additional test frequencies for Rel-12 and later and bit 2 of modifiedMPRbehavior = 1: For 5 MHz bandwidth: 2500.6 MHz, N_UL= 39686 For 10 MHz bandwidth: 2504.1 MHz, N_UL= 39731 For 15 MHz bandwidth: 2510.9 MHz, N_UL= 39799 For 20 MHz bandwidth: 2517.6 MHz, N_UL= 39866
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_04 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1 (Note 1)	5MHz	N/A for A-MPR testing		64QAM	16	9
2 (Note 2)	5MHz			64QAM	25	0
3	10MHz			64QAM	50	0
4	15MHz			64QAM	75	0
5	20MHz			64QAM	100	0
Note 1: Only applicable for Low Range. Note 2: Only applicable for Mid, High Range and additional test frequencies. Note 3: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_04.

Table 6.6.3.3_1.4.1-2: Test Configuration Table (network signalled value "NS_05")

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1			Normal
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1			Low range, Mid range In case of Low range: – For 5MHz Channel Bandwidth: 1927.2MHz (N_UL = 18072) – For 10MHz Channel Bandwidth: 1934.7MHz (N_UL = 18147) – For 15MHz Channel Bandwidth: 1932.5MHz (N_UL = 18125) – For 20MHz Channel Bandwidth: 1930MHz (N_UL = 18100)
Test Channel Bandwidths as specified in TS 36.508 [7] subclause 4.3.1			5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
	Downlink Configuration			Uplink Configuration
Ch BW	Mod’n	RB allocation		Mod’n	RB allocation
		FDD	TDD		FDD	TDD
5MHz	N/A for Additional Spurious Emissions testing			64QAM	25	NA
10MHz				64QAM	50 (Note 1)
15MHz				64QAM	75 (Note 1)
20MHz				64QAM	100 (Note 1)
10MHz				64QAM	50 (Note 2)
15MHz				64QAM	75 (Note 2)
20MHz				64QAM	100 (Note 2)
Note 1: Applies only for Low Range. Note 2: Applies only for Mid Range. Note 3: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_05.

Table 6.6.3.3_1.4.1-3: Test Configuration Table (network signalled value "NS_07")

Initial Conditions
Test Environment as specified in TS 36.508 [7] subclause 4.1				NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1				Mid range
Test Channel Bandwidths as specified in TS 36.508 [7] subclause 4.3.1				10MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Test Number	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation	RB_start
1	10MHz	N/A for Additional Spurious Emissions testing.		64QAM	36	13
2	10MHz			64QAM	16	19
3	10MHz			64QAM	30	19
4	10MHz			64QAM	50	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_07.

Table 6.6.3.3_1.4.1-4: Test Configuration Table (network signalled value "NS_08")

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1			Normal
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1			High range
Test Channel Bandwidths as specified in TS 36.508 [7] subclause 4.3.1			5MHz, 10MHz, 15MHz
Test Parameters for Channel Bandwidths
	Downlink Configuration			Uplink Configuration
Ch BW	Mod’n	RB allocation		Mod’n	RB allocation
		FDD	TDD		FDD	TDD
5MHz	N/A for Additional Spurious Emissions testing			64QAM	25	N/A
10MHz				64QAM	50
15MHz				64QAM	75
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_08.

Table 6.6.3.3_1.4.1-5: Test Configuration Table (network signalled value "NS_09")

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1			Normal
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1			High range
Test Channel Bandwidths as specified in TS 36.508 [7] subclause 4.3.1			5MHz, 10MHz, 15MHz
Test Parameters for Channel Bandwidths
	Downlink Configuration			Uplink Configuration
Ch BW	Mod’n	RB allocation		Mod’n	RB allocation
		FDD	TDD		FDD	TDD
5MHz	N/A for Additional Spurious Emissions testing			64QAM	25	N/A
10MHz				64QAM	50
15MHz				64QAM	75
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_09.

Table 6.6.3.3_1.4.1-6: Test Configuration Table (network signalled value "NS_11")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
				Normal
Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1)				For 3 MHz Channel Bandwidth: a. 2001.5 MHz (N_UL= 25515) b. 2004.5 MHz (N_UL = 25545) For 5 MHz Channel Bandwidth a. 2002.5 MHz (N_UL = 25525) b. 2004.5 MHz (N_UL = 25545) c. 2007.5 MHz (N_UL = 25575) For 10 MHz Channel Bandwidth a. 2005 MHz (N_UL = 25550) b. 2005.5 MHz (N_UL = 25555) c. 2015 MHz (N_UL = 25650) For 15 MHz Channel Bandwidth a. 2007.5 MHz (N_UL = 25575) b. 2012.5 MHz (N_UL = 25625) For 20 MHz Channel Bandwidth a. 2010 MHz (N_UL = 25600)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				3MHz, 5MHz, 10MHz, 15MHz, 20MHz
				3MHz, 5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_11 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	3MHz	N/A for Additional Spurious Emissions testing.		64QAM	6
2	3MHz			64QAM (Note 3)	15
3	5MHz			64QAM	8
4	5MHz			64QAM (Note 3)	25
5	10MHz			64QAM	12
6	10MHz			64QAM (Note 3)	50
7	15MHz			64QAM (Note 3)	8
8	15MHz			64QAM (Note 3)	25
9	15MHz			64QAM (Note 3)	30
10	15MHz			64QAM (Note 3)	75
11	20MHz			64QAM (Note 3)	10
12	20MHz			64QAM (Note 3)	25
13	20MHz			64QAM (Note 3)	100
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 3: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_11.

Table 6.6.3.3_1.4.1-7: Test Configuration Table (network signalled value "NS_12")

Initial Conditions
Test Environment				NC
(as specified in TS 36.508 [7] subclause 4.1)
Test Frequencies				For 1.4 MHz Channel Bandwidth: UL 814.9 MHz (NUL = 26699) For 5 MHz Channel Bandwidth: UL 816.7 MHz (NUL = 26717) For 10 MHz Channel Bandwidth: UL 819.2 MHz (NUL = 26742) For 15 MHz Channel Bandwidth: UL 821.7 MHz (NUL = 26767)
(as specified in TS36.508 [7] subclause 4.3.1)
Test Channel Bandwidths				1.4 MHz, 5 MHz, 10 MHz and 15 MHz
(as specified in TS 36.508 [7] subclause 4.3.1)
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Test Number	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	1.4 MHz	N/A for Additional Spurious Emissions testing		64QAM	6	0
2	5 MHz			64QAM	25	0
3	10 MHz			64QAM	50	0
4	15 MHz			64QAM	75	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_12.

Table6.6.3.3_1.4.1-8: Test Configuration Table (network signalled value "NS_13")

Initial Conditions
Test Environment				NC
(as specified in TS 36.508 [7] subclause 4.1)
Test Frequencies				For 5 MHz Channel Bandwidth: UL 821.5 MHz (NUL = 26765)
(as specified in TS36.508 [7] subclause 4.3.1)
Test Channel Bandwidths				5 MHz
(as specified in TS 36.508 [7] subclause 4.3.1)
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Test Number	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	5 MHz	N/A for Additional Spurious Emissions testing		64QAM	25	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_13.

Table 6.6.3.3_1.4.1-9: Test Configuration Table (network signalled value "NS_14")

Initial Conditions
Test Environment				NC
(as specified in TS 36.508 [7] subclause 4.1)
Test Frequencies				For 10 MHz Channel Bandwidth: UL 829 MHz (N_UL = 26840) For 15 MHz Channel Bandwidth: Mid range
(as specified in TS36.508 [7] subclause 4.3.1)
Test Channel Bandwidths				10 MHz, 15 MHz
(as specified in TS 36.508 [7] subclause 4.3.1)
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Test Number	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	10 MHz	N/A for Additional Spurious Emissions testing		64QAM	50	0
2	15 MHz			64QAM	75	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_14.

Table 6.6.3.3_1.4.1-10: Test Configuration Table (network signalled value "NS_15")

Initial Conditions

Test Environment

(as specified in TS 36.508 [7] subclause 4.1)

Test Frequencies

(as specified in TS36.508 [7] subclause 4.3.1)

High range

Test Channel Bandwidths

(as specified in TS 36.508 [7] subclause 4.3.1)

1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz

Test Parameters for Channel Bandwidths

Downlink Configuration

Uplink Configuration

Configuration ID

Ch BW

Mod’n

RB allocation

Mod’n

RB allocation FDD

RBstart FDD

1.4 MHz

N/A for Additional Spurious Emissions testing

64QAM

3 MHz

64QAM

5 MHz

64QAM

10 MHz

64QAM

15 MHz

64QAM

Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_15.

Table 6.6.3.3_1.4.1-11: Test Configuration Table (network signalled value "NS_16")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1)				For 1.4 MHz Channel Bandwidth: Low range For 3 MHz Channel Bandwidth: Low range, 810 MHz (N_UL= 27070) For 5 MHz Channel Bandwidth: Low range, 811 MHz (N_UL= 27080) , 814.5 MHz (N_UL= 27115) For 10 MHz Channel Bandwidth: Low range, 813.5 MHz (N_UL= 27105), 817 MHz (N_UL= 27140)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				1.4 MHz, 3 MHz, 5 MHz, 10 MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	1.4 MHz	N/A for Additional Spurious Emissions testing.		64QAM	6	0
2	3 MHz			64QAM	15	0
3	5 MHz			64QAM	25	0
4	10 MHz			64QAM	50	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_16.

Table 6.6.3.3_1.4.1-12: Test Configuration Table (network signalled value "NS_17")

Initial Conditions
Test Environment (as specified in TS 36.508[7] subclause 4.1)				Normal
Test Frequencies (as specified inTS36.508 [7] subclause 4.3.1)				Mid range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for Additional Spurious Emissions testing.		64QAM	25

2	10MHz			64QAM	50

Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_17.

Table 6.6.3.3_1.4.1-13: Test Configuration Table (network signalled value "NS_18")

Initial Conditions
Test Environment (as specified in TS 36.508[7] subclause 4.1)				Normal
Test Frequencies (as specified inTS36.508 [7] subclause 4.3.1)				Low range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for Additional Spurious Emissions testing.		64QAM	25
2	10MHz			64QAM	50
3	15MHz			64QAM	75
4	20MHz			64QAM	100
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_18.

Table 6.6.3.3_1.4.1-14: Test Configuration Table (network signalled value "NS_19")

Initial Conditions
Test Environment (as specified in TS 36.508[7] subclause 4.1)				Normal
Test Frequencies (as specified inTS36.508 [7] subclause 4.3.1)				Low range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				3MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation TDD
1	3MHz	N/A for Additional Spurious Emissions testing.		64QAM	15
2	10MHz			64QAM	40
3	15MHz			64QAM	45
4	20MHz			64QAM	50
Note 1: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 2: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_19.

Table 6.6.3.3_1.4.1-15: Test Configuration Table (network signalled value "NS_20")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
				Normal
Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1)				For 5 MHz Channel Bandwidth a. 2002.5 MHz (N_UL = 25525) b. 2007.5 MHz (N_UL = 25575) c. 2012.5 MHz (N_UL = 25625) d. 2017.5 MHz (N_UL = 25675) For 10 MHz Channel Bandwidth a. 2005 MHz (N_UL = 25550) b. 2015 MHz (N_UL = 25650) For 15 MHz Channel Bandwidth a. 2012.5 MHz (N_UL = 25625) For 20 MHz Channel Bandwidth a. 2010 MHz (N_UL = 25600)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_20 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for Additional Spurious Emissions testing.		64QAM (Note 3)	15
2	5MHz			64QAM (Note 3)	25
3	10MHz			64QAM	12
4	10MHz			64QAM (Note 3)	50
5	15MHz			64QAM (Note 3)	25
6	15MHz			64QAM (Note 3)	36
7	15MHz			64QAM (Note 3)	75
8	20MHz			64QAM	18
9	20MHz			64QAM (Note 3)	25
10	20MHz			64QAM (Note 3)	75
11	20MHz			64QAM (Note 3)	100
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 3: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_20.

Table 6.6.3.3_1.4.1-16: Test Configuration Table (network signalled value "NS_21")

Initial Conditions

Test Environment

(as specified in TS 36.508 [7] subclause 4.1)

Test Frequencies

(as specified in TS36.508 [7] subclause 4.3.1)

High range

Test Channel Bandwidths

(as specified in TS 36.508 [7] subclause 4.3.1)

10 MHz

Test Parameters for Channel Bandwidths

Downlink Configuration

Uplink Configuration

Configuration ID

Ch BW

Mod’n

RB allocation

Mod’n

RB allocation FDD

RBstart FDD

1 (note 1)

10 MHz

N/A for Additional Spurious Emissions testing.

64QAM

Note 1: Applicable only to high range frequency testing.

Note 2: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_21.

Table 6.6.3.3_1.4.1-17: Test Configuration Table (network signalled value "NS_22")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range, Mid Range, High Range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_22 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation TDD	RB_start TDD
1	5MHz	N/A for A-MPR testing		64QAM	1	0
2	5MHz			64QAM	1	24
3	10MHz			64QAM	1	0
4	10MHz			64QAM	1	49
5	15MHz			64QAM	1	0
6	15MHz			64QAM	1	74
7	20MHz			64QAM	1	0
8	20MHz			64QAM	1	99
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_22.

Table 6.6.3.3_1.4.1-18: Test Configuration Table (network signalled value "NS_23")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range, Mid Range, High Range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz
Test Parameters for NS_23 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation TDD	RB_start TDD
1	5MHz	N/A for A-MPR testing		64QAM	1	0
2	5MHz			64QAM	1	24
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_23.

Table 6.6.3.3_1.4.1-19: Test Configuration Table (network signalled value "NS_24")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 2007.5 MHz (N_UL= high range) 10 and 15 MHz CH BW: 1980 MHz (N_UL = 131672) 1990 MHz (N_UL = 131772) 20 MHz CH BW: 2000 MHz (N_UL= high range)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_24 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	2007.5	5MHz	N/A for A-MPR testing		64QAM	25	0
2	1980	10MHz			64QAM	50	0
3	1990	10MHz			64QAM	50	0
4	1980	15MHz			64QAM	75	0
5	2000	20MHz			64QAM	100	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_24.

Table 6.6.3.3_1.4.1-20: Test Configuration Table (network signalled value "NS_25")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 2007.5 MHz (N_UL= high range)10 and 15 MHz CH BW: 1980 MHz (N_UL = 131672) 1990 MHz (N_UL = 131772) 20 MHz CH BW: 2000 MHz (N_UL= high range)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_25 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	2007.5	5MHz	N/A for A-MPR testing		64QAM	25	0
2	1980	10MHz			64QAM	50	0
3	1990	10MHz			64QAM	50	0
4	1980	15MHz			64QAM	75	0
5	1980	20MHz			64QAM	100	0
6	2000	20MHz			64QAM	100	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_25.

Table 6.6.3.3_1.4.1-21: Test Configuration Table (network signalled value "NS_27")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to Frequency columnin test parameters
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_27 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	Frequency	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	Low/Mid/High	5MHz			64QAM	25	0
2	Low/Mid/High	10MHz			64QAM	50	0
3	Low/Mid/High	15MHz			64QAM	75	0
4	Low/Mid/High	20MHz			64QAM	100	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_27.

Table 6.6.3.3_1.4.1-22: Test Configuration Table (network signalled value "NS_36")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 700.5 MHz (N_UL = low range) 705.5 MHz (N_UL=132747) 10 MHz CH BW: 703 MHz (N_UL = low range) 708 MHz (N_UL = 132772) 15 MHz CH BW: 705.5 MHz (N_UL = low range) 710.5 MHz (N_UL =132797 )
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz
Test Parameters for NS_36 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	700.5	5MHz	N/A for A-MPR testing		64QAM	25	0
2	705.5	5MHz			64QAM	25	0
3	703	10MHz			64QAM	50	0
4	708	10MHz			64QAM	50	0
5	705.5	15MHz			64QAM	75	0
6	710.5	15MHz			64QAM	75	0
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Void. Note 3: Void. Note 4: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_36.

Table 6.6.3.3_1.4.1-23: Test Configuration Table (network signalled value "NS_56")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 1630 MHz (low range) 10 MHz CH BW: 1632.5 MHz (low range)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz
Test Parameters for NS_56 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	1630	5MHz	N/A for A-MPR testing		64QAM	1	0
2	1630	5MHz			64QAM	25	0
3	1632.5	10MHz			64QAM	1	0
4	1632.5	10MHz			64QAM	50	0
Note 1: The 64QAM configurations shall not apply to UEs for which TC 6.6.3.3_2 is executed with network signalled value NS_56.

Editor’s note: The following lines belong at the end of section 6.6.3.3_1.4.1. As new tables are added to this section, these lines should always follow the tables.

1. Connect the SS to the UE to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure A.7.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals are initially set up according to Annex C0, C.1 and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Table 6.6.3.3_1.4.1-1 to Table 6.6.3.3_1.4.1-22 depending on network signal value.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.3_1.4.3.

6.6.3.3_1.4.2 Test procedure

Same test procedure as in clause 6.6.3.3.4.2.

6.6.3.3_1.4.3 Message contents

Same message contents as in clause 6.6.3.3.4.3.

6.6.3.3_1.5 Test requirement

Same test requirement as in clause 6.6.3.3.5.

6.6.3.3_2 Additional spurious emissions for UL 256QAM

6.6.3.3_2.1 Test purpose

Same test purpose as in clause 6.6.3.3.1.

6.6.3.3_2.2 Test applicability

This test case applies to all types of E-UTRA UE from release 14 and forward that support UL 256QAM.

6.6.3.3_2.3 Minimum conformance requirements

Same minimum conformance requirements as in clause 6.6.3.3.3.

6.6.3.3_2.4 Test description

6.6.3.3_2.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and channel bandwidths based on E-UTRA operating bands specified in table 5.4.2.1-1. All of these configurations shall be tested with applicable test parameters for each channel bandwidth, and are shown in Table 6.6.3.3_2.4.1-1 through Table 6.6.3.3_2.4.1-22. The details of the uplink reference measurement channels (RMCs) are specified in Annexes A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.3_2.4.1-1: Test Configuration Table (network signalled value "NS_04")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range, Mid Range, High Range Additional test frequencies for Rel-12 to Rel-13 and bit 2 of modifiedMPRbehavior = 0: For 5 MHz bandwidth: 2499.6 MHz, N_UL= 39696 For 10 MHz bandwidth: 2504.1 MHz, N_UL= 39731 For 15 MHz bandwidth: 2510.9 MHz, N_UL= 39799 For 20 MHz bandwidth: 2517.6 MHz, N_UL= 39866 Additional test frequencies for Rel-12 and later and bit 2 of modifiedMPRbehavior = 1: For 5 MHz bandwidth: 2500.6 MHz, N_UL= 39686 For 10 MHz bandwidth: 2504.1 MHz, N_UL= 39731 For 15 MHz bandwidth: 2510.9 MHz, N_UL= 39799 For 20 MHz bandwidth: 2517.6 MHz, N_UL= 39866
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1 (Note 1)	5MHz	N/A for Additional Spurious Emissions testing		256QAM	16	9
2 (Note 2)	5MHz			256QAM	25	0
3	10MHz			256QAM	50	0
4	15MHz			256QAM	75	0
5	20MHz			256QAM	100	0
Note 1: Only applicable for Low Range. Note 2: Only applicable for Mid, High Range and additional test frequencies.

Table 6.6.3.3_2.4.1-2: Test Configuration Table (network signalled value "NS_05")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low range, Mid range In case of Low range: – For 5 MHz Channel Bandwidth: 1927.2 MHz (NUL = 18072) – For 10 MHz Channel Bandwidth: 1934.7 MHz (NUL = 18147) – For 15 MHz Channel Bandwidth: 1932.5 MHz (NUL = 18125) – For 20 MHz Channel Bandwidth: 1930 MHz (NUL = 18100)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for Additional Spurious Emissions testing		256QAM	25
2 (Note 1)	10MHz			256QAM	50
3(Note 1)	15MHz			256QAM	75
4 (Note 1)	20MHz			256QAM	100
5 (Note 2)	10MHz			256QAM	50
6 (Note 2)	15MHz			256QAM	75
7 (Note 2)	20MHz			256QAM	100
Note 1: Applies only for Low Range. Note 2: Applies only for Mid Range.

Table 6.6.3.3_2.4.1-3: Test Configuration Table (network signalled value "NS_07")

Initial Conditions
Test Environment as specified in TS 36.508 [7] subclause 4.1				NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1				Mid range
Test Channel Bandwidths as specified in TS 36.508 [7] subclause 4.3.1				10MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation	RBstart
1	10MHz	N/A for Additional Spurious Emissions testing		256QAM	36	13
2	10MHz			256QAM	16	19
3	10MHz			256QAM	30	19
4	10MHz			256QAM	50	0

Table 6.6.3.3_2.4.1-4: Test Configuration Table (network signalled value "NS_08")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				High range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for Additional Spurious Emissions testing		256QAM	25
2	10MHz			256QAM	50
3	15MHz			256QAM	75

Table 6.6.3.3_2.4.1-5: Test Configuration Table (network signalled value "NS_09")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				High range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for Additional Spurious Emissions testing		256QAM	25
2	10MHz			256QAM	50
3	15MHz			256QAM	75

Table 6.6.3.3_2.4.1-6: Test Configuration Table (network signalled value "NS_11")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
				Normal
Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1)				For 3 MHz Channel Bandwidth: a. 2001.5 MHz (NUL = 25515) b. 2004.5 MHz (NUL = 25545) For 5 MHz Channel Bandwidth a. 2002.5 MHz (NUL = 25525) b. 2004.5 MHz (NUL = 25545) c. 2007.5 MHz (NUL = 25575) For 10 MHz Channel Bandwidth a. 2005 MHz (NUL = 25550) b. 2005.5 MHz (NUL = 25555) c. 2015 MHz (NUL = 25650) For 15 MHz Channel Bandwidth a. 2007.5 MHz (NUL = 25575) b. 2012.5 MHz (NUL = 25625) For 20 MHz Channel Bandwidth a. 2010 MHz (NUL = 25600)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				3MHz, 5MHz, 10MHz, 15MHz, 20MHz
				3MHz, 5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	3MHz	N/A for Additional Spurious Emissions testing		256QAM	15
2	5MHz			256QAM	25
3	10MHz			256QAM	50
4	15MHz			256QAM	8
5	15MHz			256QAM	25
6	15MHz			256QAM	30
7	15MHz			256QAM	75
8	20MHz			256QAM	10
9	20MHz			256QAM	25
10	20MHz			256QAM	100
Note 1: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth.

Table 6.6.3.3_2.4.1-7: Test Configuration Table (network signalled value "NS_12")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1)				For 1.4 MHz Channel Bandwidth: UL 814.9 MHz (NUL = 26699) For 5 MHz Channel Bandwidth: UL 816.7 MHz (NUL = 26717) For 10 MHz Channel Bandwidth: UL 819.2 MHz (NUL = 26742) For 15 MHz Channel Bandwidth: UL 821.7 MHz (NUL = 26767)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				1.4 MHz, 5 MHz, 10 MHz and 15 MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	1.4 MHz	N/A for Additional Spurious Emissions testing		256QAM	6	0
2	5 MHz			256QAM	25	0
3	10 MHz			256QAM	50	0
4	15 MHz			256QAM	75	0

Table6.6.3.3_2.4.1-8: Test Configuration Table (network signalled value "NS_13")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1)				For 5 MHz Channel Bandwidth: UL 821.5 MHz (NUL = 26765)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5 MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	5 MHz	N/A for Additional Spurious Emissions testing		256QAM	25	0

Table 6.6.3.3_2.4.1-9: Test Configuration Table (network signalled value "NS_14")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1)				For 10 MHz Channel Bandwidth: UL 829 MHz (N_UL = 26840) For 15 MHz Channel Bandwidth: Mid range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				10 MHz, 15 MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	10 MHz	N/A for Additional Spurious Emissions testing		256QAM	50	0
2	15 MHz			256QAM	75	0

Table 6.6.3.3_2.4.1-10: Test Configuration Table (network signalled value "NS_15")

Initial Conditions

Test Environment

(as specified in TS 36.508 [7] subclause 4.1)

Test Frequencies

(as specified in TS36.508 [7] subclause 4.3.1)

High range

Test Channel Bandwidths

(as specified in TS 36.508 [7] subclause 4.3.1)

1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz

Test Parameters for Channel Bandwidths

Downlink Configuration

Uplink Configuration

Configuration ID

Ch BW

Mod’n

RB allocation

Mod’n

RB allocation FDD

RBstart FDD

1.4 MHz

N/A for Additional Spurious Emissions testing

256QAM

3 MHz

256QAM

5 MHz

256QAM

10 MHz

256QAM

15 MHz

256QAM

Table 6.6.3.3_2.4.1-11: Test Configuration Table (network signalled value "NS_16")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1)				For 1.4 MHz Channel Bandwidth: Low range For 3 MHz Channel Bandwidth: Low range, 810 MHz (N_UL= 27070) For 5 MHz Channel Bandwidth: Low range, 811 MHz (N_UL= 27080) , 814.5 MHz (N_UL= 27115) For 10 MHz Channel Bandwidth: Low range, 813.5 MHz (N_UL= 27105), 817 MHz (N_UL= 27140)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				1.4 MHz, 3 MHz, 5 MHz, 10 MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	1.4 MHz	N/A for Additional Spurious Emissions testing		256QAM	6	0
2	3 MHz			256QAM	15	0
3	5 MHz			256QAM	25	0
4	10 MHz			256QAM	50	0

Table 6.6.3.3_2.4.1-12: Test Configuration Table (network signalled value "NS_17")

Initial Conditions
Test Environment (as specified in TS 36.508[7] subclause 4.1)				Normal
Test Frequencies (as specified inTS36.508 [7] subclause 4.3.1)				Mid range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for Additional Spurious Emissions testing		256QAM	25
2	10MHz			256QAM	50

Table 6.6.3.3_2.4.1-13: Test Configuration Table (network signalled value "NS_18")

Initial Conditions
Test Environment (as specified in TS 36.508[7] subclause 4.1)				Normal
Test Frequencies (as specified inTS36.508 [7] subclause 4.3.1)				Low range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for Additional Spurious Emissions testing		256QAM	25
2	10MHz			256QAM	50
3	15MHz			256QAM	75
4	20MHz			256QAM	100

Table 6.6.3.3_2.4.1-14: Test Configuration Table (network signalled value "NS_19")

Initial Conditions
Test Environment (as specified in TS 36.508[7] subclause 4.1)				Normal
Test Frequencies (as specified inTS36.508 [7] subclause 4.3.1)				Low range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				3MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation TDD
1	3MHz	N/A for Additional Spurious Emissions testing		256QAM	15
2	10MHz			256QAM	40
3	15MHz			256QAM	45
4	20MHz			256QAM	50
Note 1: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth.

Table 6.6.3.3_2.4.1-15: Test Configuration Table (network signalled value "NS_20")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal

Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1)				For 5 MHz Channel Bandwidth a. 2002.5 MHz (N_UL = 25525) b. 2007.5 MHz (N_UL = 25575) c. 2012.5 MHz (N_UL = 25625) d. 2017.5 MHz (N_UL = 25675) For 10 MHz Channel Bandwidth a. 2005 MHz (N_UL = 25550) b. 2015 MHz (N_UL = 25650) For 15 MHz Channel Bandwidth a. 2012.5 MHz (N_UL = 25625) For 20 MHz Channel Bandwidth a. 2010 MHz (N_UL = 25600)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz

Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD

1	5MHz	N/A for Additional Spurious Emissions testing		256QAM	15
2	5MHz			256QAM	25
3	10MHz			256QAM	50
4	15MHz			256QAM	25
5	15MHz			256QAM	36
6	15MHz			256QAM	75
7	20MHz			256QAM	25
8	20MHz			256QAM	75
9	20MHz			256QAM	100
Note 1: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth.

Table 6.6.3.3_2.4.1-16: Test Configuration Table (network signalled value "NS_21")

Initial Conditions

Test Environment

(as specified in TS 36.508 [7] subclause 4.1)

Test Frequencies

(as specified in TS36.508 [7] subclause 4.3.1)

High range

Test Channel Bandwidths

(as specified in TS 36.508 [7] subclause 4.3.1)

10 MHz

Test Parameters for Channel Bandwidths

Downlink Configuration

Uplink Configuration

Configuration ID

Ch BW

Mod’n

RB allocation

Mod’n

RB allocation FDD

RBstart FDD

10 MHz

N/A for Additional Spurious Emissions testing.

256QAM

Table 6.6.3.3_2.4.1-17: Test Configuration Table (network signalled value "NS_22")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range, Mid Range, High Range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation TDD	RB_start TDD
1	5MHz	N/A for Additional Spurious Emissions testing		256QAM	1	0
2	5MHz			256QAM	1	24
3	10MHz			256QAM	1	0
4	10MHz			256QAM	1	49
5	15MHz			256QAM	1	0
6	15MHz			256QAM	1	74
7	20MHz			256QAM	1	0
8	20MHz			256QAM	1	99

Table 6.6.3.3_2.4.1-18: Test Configuration Table (network signalled value "NS_23")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range, Mid Range, High Range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation TDD	RB_start TDD
1	5MHz	N/A for Additional Spurious Emissions testing		256QAM	1	0
2	5MHz			256QAM	1	24

Table 6.6.3.3_2.4.1-19: Test Configuration Table (network signalled value "NS_24")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 2007.5 MHz (N_UL= high range) 10 and 15 MHz CH BW: 1980 MHz (N_UL = 131672) 1990 MHz (N_UL = 131772) 20 MHz CH BW: 2000 MHz (N_UL= high range)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	2007.5	5MHz	N/A for Additional Spurious Emissions testing		256QAM	25	0
2	1980	10MHz			256QAM	50	0
3	1990	10MHz			256QAM	50	0
4	1980	15MHz			256QAM	75	0
5	2000	20MHz			256QAM	100	0

Table 6.6.3.3_2.4.1-20: Test Configuration Table (network signalled value "NS_25")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 2007.5 MHz (N_UL= high range)10 and 15 MHz CH BW: 1980 MHz (N_UL = 131672) 1990 MHz (N_UL = 131772) 20 MHz CH BW: 2000 MHz (N_UL= high range)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	2007.5	5MHz	N/A for Additional Spurious Emissions testing		256QAM	25	0
2	1980	10MHz			256QAM	50	0
3	1990	10MHz			256QAM	50	0
4	1980	15MHz			256QAM	75	0
5	1980	20MHz			256QAM	100	0
6	2000	20MHz			256QAM	100	0

Table 6.6.3.3_2.4.1-21: Test Configuration Table (network signalled value "NS_27")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to Frequency columnin test parameters
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
			Downlink Configuration		Uplink Configuration
Configuration ID	Frequency	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	Low/Mid/High	5MHz	N/A for Additional Spurious Emissions testing		256QAM	25	0
2	Low/Mid/High	10MHz			256QAM	50	0
3	Low/Mid/High	15MHz			256QAM	75	0
4	Low/Mid/High	20MHz			256QAM	100	0

Table 6.6.3.3_2.4.1-22: Test Configuration Table (network signalled value "NS_36")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 700.5 MHz (N_UL = low range) 705.5 MHz (N_UL=132747) 10 MHz CH BW: 703 MHz (N_UL = low range) 708 MHz (N_UL = 132772) 15 MHz CH BW: 705.5 MHz (N_UL = low range) 710.5 MHz (N_UL =132797 )
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz
Test Parameters for Channel Bandwidths
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	700.5	5MHz	N/A for Additional Spurious Emissions testing		256QAM	25	0
2	705.5	5MHz			256QAM	25	0
3	703	10MHz			256QAM	50	0
4	708	10MHz			256QAM	50	0
5	705.5	15MHz			256QAM	75	0
6	710.5	15MHz			256QAM	75	0

Table 6.6.3.3_2.4.1-23: Test Configuration Table (network signalled value "NS_56")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 1630 MHz (low range) 10 MHz CH BW: 1632.5 MHz (low range)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz
Test Parameters for NS_56 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	1630	5MHz	N/A for A-MPR testing		256QAM	1	0
2	1630	5MHz			256QAM	25	0
3	1632.5	10MHz			256QAM	1	0
4	1632.5	10MHz			256QAM	50	0

Editor’s note: The following lines belong at the end of section 6.6.3.3_2.4.1. As new tables are added to this section, these lines should always follow the tables.

1. Connect the SS to the UE to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure A.7.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals are initially set up according to Annex C0, C.1 and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Table 6.6.3.3_2.4.1-1 to Table 6.6.3.3_2.4.1-22 depending on network signal value.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.3_2.4.3.

6.6.3.3_2.4.2 Test procedure

1. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 6.6.3.3_2.4.1-1 to 6.6.3.3_2.4.1-22. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

2. Send continuously uplink power control "up" commands in the uplink scheduling information to the UE until the UE transmits at P_UMAX level.

3. Measure the mean power of the UE in the channel bandwidth of the radio access mode according to the test configuration, which shall meet the requirements described in Tables 6.2.4_4.5-1 to 6.2.4_4.5‑29 for Power Class 3 UEs as appropriate. The period of the measurement shall be at least one sub-frame (1ms).

4. Measure the power of the transmitted signal with a measurement filter of bandwidths according to Table 6.6.3.3.5.1-1 to 6.6.3.3.5.22-1 as appropriate. The centre frequency of the filter shall be stepped in contiguous steps according to the same table. For NS_07 measurements made in a bandwidth of 6.25kHz, measurement parameter settings defined in table 6.6.3.3.4.2-1 shall be used. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

6.6.3.3_2.4.3 Message contents

Same message contents as in clause 6.6.3.3.4.3.

6.6.3.3_2.5 Test requirement

Same test requirement as in clause 6.6.3.3.5.

6.6.3.3A Additional spurious emissions for CA

Editor’s note: Test configuration for CA_41C (CA_NS_04) needs further analysed.

6.6.3.3A.1 Additional spurious emissions for CA (intra-band contiguous DL CA and UL CA)

6.6.3.3A.1.1 Test purpose

To verify that UE transmitter does not cause unacceptable interference to other channels or other systems in terms of transmitter spurious emissions in intra-band contiguous carrier aggregation under the deployment scenarios where additional requirements are specified.

6.6.3.3A.1.2 Test applicability

This test case applies to all types of E-UTRA UE release 10 and forward that support intra-band contiguous DL CA and UL CA but do not support UL 64QAM or UL 256QAM.

6.6.3.3A.1.3 Minimum conformance requirements

This clause specifies the requirements for the specified E-UTRA band for an additional spectrum emission for CA requirement with protected bands as indicated from Table 6.6.3.3A.1.3.1-1 to Table 6.6.3.3A.1.3.6-1.

6.6.3.3A.1.3.1 Minimum conformance requirements for CA_1C (network signalled value "CA_NS_01")

When "CA_NS_01" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3A.1.3.1-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1A.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3A.1.3.1-1: Additional requirements (PHS) for CA

Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Note
E-UTRA band 34	F_{DL_low}	–	F_{DL_high}	-50	1
Frequency range	1884.5	–	1915.7	-41	0.3	1
Note 1: Applicable when the aggregated channel bandwidth is confined within frequency range 1940 – 1980 MHz

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3A.1.

6.6.3.3A.1.3.2 Minimum conformance requirements for CA_1C (network signalled value “CA_NS_02")

When “CA_NS_02” is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3A.1.3.2-1. These requirements also apply for the frequency ranges that are less than Δf_OOB(MHz) in Table 6.6.3.1A.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3A.1.3.2-1: Additional requirements for CA

Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)
E-UTRA band 34	F_{DL_low}	–	F_{DL_high}	-50	1
Frequency range	1900	–	1915	-15.5	5
Frequency range	1915	–	1920	+1.6	5

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3A.2.

6.6.3.3A.1.3.3 Minimum requirement for CA_1C (network signalled value “CA_NS_03”)

When “CA_NS_03” is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3A.1.3.3-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1A.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3A.1.3.3-1: Additional requirement for CA

Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)
E-UTRA band 34	F_{DL_low}	–	F_{DL_high}	-50	1
Frequency range	1880	–	1895	-40	1
Frequency range	1895	–	1915	-15.5	5
Frequency range	1915	–	1920	+1.6	5

6.6.3.3A.1.3.4 Minimum requirement for CA_38C (network signalled value "CA_NS_05")

When "CA_NS_05" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3A.1.3.4-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1A.1.3-1 from the edge of the aggregated channel bandwidth.

Table 6.6.3.3A.1.3.4-1: Additional requirements

Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)
Frequency range	2620	–	2645	-15.5	5
Frequency range	2645	–	2690	-40	1

6.6.3.3A.1.3.5 Minimum requirement for CA_7C (network signalled value "CA_NS_06")

When "CA_NS_06" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3A.1.3.5-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1A.3-1 from the edge of the aggregated channel bandwidth.

Table 6.6.3.3A.1.3.5-1: Additional requirements

Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)
Frequency range	2570	–	2575	+1.6	5
Frequency range	2575	–	2595	-15.5	5
Frequency range	2595	–	2620	-40	1

6.6.3.3A.1.3.6 Minimum requirement for CA_39C (network signalled value "CA_NS_07")

When "CA_NS_07" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3A.1.3.6-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1A.1.3-1 from the edge of the aggregated channel bandwidth.

Table 6.6.3.3A.1.3.6-1: Additional requirements

Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
Frequency range	1805	–	1855	-40	1	1
Frequency range	1855	–	1880	-15.5	5	1, 2, 3
NOTE 1: This requirement is applicable for carriers with aggregated channel bandwidths confined in 1885-1920 MHz. NOTE 2: These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.0-1 from the edge of the aggregated channel bandwidth. NOTE 3: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band.

6.6.3.3A.1.3.7 Minimum requirement for CA_42C (network signalled value "CA_NS_08")

When "CA_NS_08" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3A.7-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1A.1.3-1 from the edge of the aggregated channel bandwidth.

Table 6.6.3.3A.1.7-1: Additional requirements

Frequency band (MHz)	Aggregated bandwidth / Spectrum emission limit (dBm)	MBW
	25, 30, 35, 40 MHz (Note 1)
3400 ≤ f ≤ 3800	-23 (Note 2, Note 4)	5 MHz
	-40 (Note 3)	1 MHz
NOTE 1: Possible aggregated bandwidth for CA_42C as specified in Table 5.4.2A.1-1. NOTE 2: This requirement applies within an offset between 5 MHz and 25 MHz from the lower and from the upper edge of the channel bandwidth, whenever these frequencies overlap with the specified frequency band. NOTE 3: This requirement applies from 3400 MHz to 25 MHz below the lower E-UTRA channel edge and from 25 MHz above the upper E-UTRA channel edge to 3800 MHz. NOTE 4: This emission limit might imply risk of harmful interference to UE(s) operating in the protected operating band.

6.6.3.3A.1.3.8 Minimum requirement for CA_41C (network signalled value "CA_NS_04"

When "CA_NS_04" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3A.1.3.8-1. This requirement also applies for the frequency ranges that are less than F_OOB (MHz) in Table 6.6.3.1A.1.3-1 from the edge of the aggregated channel bandwidth.

Table 6.6.3.3A.1.3.8-1: Additional requirements

Frequency band	Spectrum emission limit (dBm)	Measurement bandwidth
2490.5 MHz ≤ f < 2495 MHz	-13	1 MHz
9 kHz < f < 2490.5 MHz	-25	1 MHz

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3A.3.

6.6.3.3A.1.4 Test description

6.6.3.3A.1.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and CC combinations based on E-UTRA CA configurations specified in table 5.4.2A.1-1. All of these configurations shall be tested with applicable test parameters for each CA Configuration, and are shown in tables’ 6.6.3.3A.1.4.1-1 to 6.6.3.3A.1.4.1-3. The details of the uplink reference measurement channels (RMCs) are specified in Annexes A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.3A.1.4.1-1: Test Configuration Table for CA (network signalled value “CA_NS_01”)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						Lowest N_{RB_agg}Highest N_{RB_agg}
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	QPSK	1		P_1@0	S_0@0
2	75	75		QPSK	150		P_75@0	S_75@0
3	75	75		QPSK	45		P_45@7	S_0@0
4	75	75		QPSK	8		P_0@0	S_8@67
5	75	75		QPSK	129		P_75@0	S_54@0
6	75	75		QPSK	2		P_1@0	S_1@74
7	100	100		QPSK	200		P_100@0	S_100@0
8	100	100		QPSK	1		P_1@0	S_0@0
9	100	100		QPSK	175		P_75@25	S_100@0
10	100	100		QPSK	25		P_0@0	S_25@75
11	100	100		QPSK	64		P_64@24	S_0@0
12	100	100		QPSK	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

Table 6.6.3.3A.1.4.1-2: Test Configuration Table for CA (network signalled value "CA_NS_02")

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						Lowest N_{RB_agg} Highest N_{RB_agg}
Test Parameters for CA Configurations
ID	CA Configuration / NR_{B_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	QPSK	1		P_1@0	S_0@0
2	75	75		QPSK	75		P_75@0	S_0@0
3	75	75		QPSK	129		P_75@0	S_54@0
4	75	75		QPSK	129		P_54@21	S_75@0
5	75	75		QPSK	1		P_0@0	S_1@74
6	75	75		QPSK	1		P_0@0	S_1@54
7	75	75		QPSK	2		P_1@0	S_1@74
8	100	100		QPSK	1		P_1@0	S_0@0
9	100	100		QPSK	1		P_1@21	S_0@0
10	100	100		QPSK	90		P_90@0	S_0@0
11	100	100		QPSK	180		P_100@0	S_80@0
12	100	100		QPSK	1		P_0@0	S_1@99
13	100	100		QPSK	1		P_0@0	S_1@83
14	100	100		QPSK	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

Table 6.6.3.3A.1.4.1-3: Test Configuration Table for CA (network signalled value “CA_NS_03”)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						Lowest N_{RB_agg}Highest N_{RB_agg}
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	QPSK	1		P_1@0	S_0@0
2	75	75		QPSK	1		P_1@21	S_0@0
3	75	75		QPSK	75		P_75@0	S_0@0
4	75	75		QPSK	90		P_75@0	S_15@0
5	75	75		QPSK	150		P_75@0	S_75@0
6	75	75		QPSK	1		P_0@0	S_1@74
7	75	75		QPSK	1		P_0@0	S_1@44
8	75	75		QPSK	2		P_1@0	S_1@74
9	100	100		QPSK	1		P_1@0	S_0@0
10	100	100		QPSK	60		P_60@0	S_0@0
11	100	100		QPSK	1		P_1@63	S_0@0
12	100	100		QPSK	90		P_90@0	S_0@0
13	100	100		QPSK	164		P_100@0	S_64@0
14	100	100		QPSK	1		P_0@0	S_1@99
15	100	100		QPSK	1		P_0@0	S_1@70
16	100	100		QPSK	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

Table 6.6.3.3A.1.4.1-4: Test Configuration Table for CA (network signalled value “CA_NS_05”)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						Lowest N_{RB_agg}Highest N_{RB_agg}
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	QPSK	40		P_40@0	S_0@0
2	75	75		QPSK	80		P_50@25	S_30@0
3	75	75		QPSK	60		P_10@65	S_50@0
4	75	75		QPSK	65		P_1@74	S_64@0
5	75	75		QPSK	92		P_20@55	S_72@0
6	75	75		QPSK	2		P_1@0	S_1@74
7	100	100		QPSK	8		P_8@0	S_0@0
8	100	100		QPSK	40		P_40@0	S_0@0
9	100	100		QPSK	80		P_50@50	S_30@0
10	100	100		QPSK	150		P_60@40	S_90@0
11	100	100		QPSK	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

Table 6.6.3.3A.1.4.1-5: Test Configuration Table (network signalled value "CA_NS_06")

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						As in Table 6.2.4A.1.3.6-1
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	QPSK	5		P_5@0	S_0@0
2	75	75		QPSK	45		P_45@0	S_0@0
3	75	75		QPSK	75		P_60@15	S_15@0
4	75	75		QPSK	60		P_10@65	S_50@0
5	75	75		QPSK	90		P_18@57	S_72@0
6	75	75		QPSK	2		P_1@0	S_1@74
7	100	100		QPSK	10		P_10@0	S_0@0
8	100	100		QPSK	30		P_30@0	S_0@0
9	100	100		QPSK	100		P_75@25	S_25@0
10	100	100		QPSK	90		P_40@60	S_50@0
11	100	100		QPSK	96		P_15@85	S_81@0
12	100	100		QPSK	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1.

Table 6.6.3.3A.1.4.1-6: Test Configuration Table for CA (network signalled value “CA_NS_07”)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						As in Table 6.2.4A.1.3.7-1
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	100	25	N/A	QPSK	1		P_1@0	S_0@0
2	100	25		QPSK	85		P_80@20	S_5@0
3	100	25		QPSK	65		P_60@40	S_5@0
4	100	25		QPSK	35		P_30@70	S_5@0
5	100	25		QPSK	2		P_1@0	S_1@24
6	100	50		QPSK	1		P_1@1	S_0@0
7	100	50		QPSK	10		P_10@30	S_0@0
8	100	50		QPSK	30		P_30@30	S_0@0
9	100	50		QPSK	60		P_40@60	S_20@0
10	100	50		QPSK	30		P_10@90	S_20@0
11	100	50		QPSK	5		P_0@0	S_5@45
12	100	50		QPSK	2		P_1@0	S_1@49
13	100	75		QPSK	1		P_1@1	S_0@0
14	100	75		QPSK	40		P_40@20	S_0@0
15	100	75		QPSK	85		P_80@20	S_5@0
16	100	75		QPSK	40		P_0@0	S_40@20
17	100	75		QPSK	15		P_0@0	S_15@60
18	100	75		QPSK	2		P_1@0	S_1@74
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

Table 6.6.3.3A.1.4.1-7: Test Configuration Table for CA (network signalled value “CA_NS_08”)

FFS

Table 6.6.3.3A.1.4.1-8: Test Configuration Table for CA (network signalled value “CA_NS_04”)

Initial Conditions
Test Environment as specified in TS 36.508 [7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						As in Table 6.2.4A.1.3.4-1
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	100	50	N/A	QPSK	10		P_10@20	S_0@0
2	100	50		QPSK	60		P_50@50	S_10@0
3	100	50		QPSK	15		P_0@0	S_15@0
4	100	50		QPSK	2		P_1@0	S_1@49
5	75	75		QPSK	10		P_10@20	S_0@0
6	75	75		QPSK	75		P_30@45	S_45@0
7	75	75		QPSK	2		P_1@0	S_1@74
8	100	75		QPSK	10		P_10@20	S_0@0
9	100	75		QPSK	80		P_50@50	S_30@0
10	100	75		QPSK	20		P_0@0	S_20@15
11	100	75		QPSK	2		P_1@0	S_1@74
12	100	100		QPSK	10		P_10@25	S_0@0
13	100	100		QPSK	90		P_40@60	S_50@0
14	100	100		QPSK	15		P_0@0	S_15@40
15	100	100		QPSK	20		P_0@0	S_20@30
16	100	100			2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1.

1. Connect the SS to the UE to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure group A.33 as appropriate.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals for PCC are initially set up according to Annex C.0, C.1 and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Table 6.6.3.3A.1.4.1-1, Table 6.6.3.3A.1.4.1-2, Table 6.6.3.3A.1.4.1-3, Table 6.6.3.3A.1.4.1-4, Table 6.6.3.3A.1.4.1-5 or Table 6.6.3.3A.1.4.1-6 depending on network signal value.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.3A.1.4.3.

6.6.3.3A.1.4.2 Test procedure

1. Configure SCC according to Annex C.0, C.1 and Annex C.3.0 for all downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4. Message contents are defined in clause 6.6.3.3A.1.4.3

3. SS activates SCC by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC on both PCC and SCC, according to Table 6.6.3.3A.1.4.1-1, Table 6.6.3.3A.1.4.1-2, Table 6.6.3.3A.1.4.1-3, Table 6.6.3.3A.1.4.1-4, Table 6.6.3.3A.1.4.1-5 or Table 6.6.3.3A.1.4.1-6 depending on network signal value. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

5. Send continuously uplink power control “up” commands in every uplink scheduling information to the UE until the UE transmits at P_UMAX level.

6. Measure the mean power of the UE in the channel bandwidth of the radio access mode according to the test configuration, which shall meet the requirements described in Tables 6.2.4A.1.5-1 to 6.2.4A.1.5-7 as appropriate. The period of the measurement shall be at least one sub-frame (1ms).

7. Measure the power of the transmitted signal with a measurement filter of bandwidths according to Table 6.6.3.3A.1.5.1-1, 6.6.3.3A.1.5.2-1, 6.6.3.3A.1.5.3-1, 6.6.3.3A.1.5.4-1, 6.6.3.3A.1.5.5-1 and 6.6.3.3A.1.5.6-1 as appropriate. The centre frequency of the filter shall be stepped in contiguous steps according to the same table. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

6.6.3.3A.1.4.3 Message contents

Message contents are according to TS 36.508 [7] subclause 4.6, with the following exceptions for each network signalled value.

6.6.3.3A.1.4.3.1 Message contents (network signalled value "CA_NS_01")

1. Information element additionalSpectrumEmissionSCell-r10 is set to CA_NS_01. This can be set in the RadioResourceConfigCommonSCell-r10-DEFAULT as part of the common RRC messages. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3A.1.4.3.1-1: RadioResourceConfigCommonSCell-r10-DEFAULT: Additional spectrum emission test requirement for “CA_NS_01”

Derivation Path: TS 36.508 [7] clause 4.6.3, Table 4.6.3-13A
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmissionSCell-r10	1 (CA_NS_01)

6.6.3.3A.1.4.3.2 Message contents exceptions (network signalled value "CA_NS_02")

1. Information element additionalSpectrumEmissionSCell-r10 is set to CA_NS_02. This can be set in the RadioResourceConfigCommonSCell-r10-DEFAULT as part of the common RRC messages. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3A.1.4.3.2-1: RadioResourceConfigCommonSCell-r10-DEFAULT: Additional spectrum emission test requirement for “CA_NS_02”

Derivation Path: TS 36.508 [7] clause 4.6.3, Table 4.6.3-13A
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmissionSCell-r10	2 (CA_NS_02)

6.6.3.3A.1.4.3.3 Message contents exceptions (network signalled value “CA_NS_03")

1. Information element additionalSpectrumEmission is set to NS_08. This can be set in the RadioResourceConfigCommonSCell-r10-DEFAULT as part of the common RRC messages. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3A.1.4.3.3-1: RadioResourceConfigCommonSCell-r10-DEFAULT: Additional spectrum emission test requirement for “CA_NS_03”

Derivation Path: TS 36.508 [7] clause 4.6.3, Table 4.6.3-13A
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmissionSCell-r10	3 (CA_NS_03)

6.6.3.3A.1.4.3.4 Message contents exceptions (network signalled value “CA_NS_05")

1. Information element additionalSpectrumEmission is set to CA_NS_05. This can be set in the RadioResourceConfigCommonSCell-r10-DEFAULT as part of the common RRC messages. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3A.1.4.3.4-1: RadioResourceConfigCommonSCell-r10-DEFAULT: Additional spectrum emission test requirement for “CA_NS_05”

Derivation Path: TS 36.508 [7] clause 4.6.3, Table 4.6.3-13A
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmissionSCell-r10	5 (CA_NS_05)

6.6.3.3A.1.4.3.5 Message contents exceptions (network signalled value “CA_NS_06")

1. Information element additionalSpectrumEmission is set to CA_NS_06. This can be set in the RadioResourceConfigCommonSCell-r10-DEFAULT as part of the common RRC messages. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3A.1.4.3.5-1: RadioResourceConfigCommonSCell-r10-DEFAULT: Additional spectrum emission test requirement for “CA_NS_06”

Derivation Path: TS 36.508 [7] clause 4.6.3, Table 4.6.3-13A
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmissionSCell-r10	6 (CA_NS_06)

6.6.3.3A.1.4.3.6 Message contents exceptions (network signalled value “CA_NS_07")

1. Information element additionalSpectrumEmission is set to CA_NS_07. This can be set in the RadioResourceConfigCommonSCell-r10-DEFAULT as part of the common RRC messages. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3A.1.4.3.6-1: RadioResourceConfigCommonSCell-r10-DEFAULT: Additional spectrum emission test requirement for “CA_NS_07”

Derivation Path: TS 36.508 [7] clause 4.6.3, Table 4.6.3-13A
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmissionSCell-r10	7 (CA_NS_07)

6.6.3.3A.1.4.3.7 Message contents exceptions (network signalled value “CA_NS_08")

FFS

6.6.3.3A.1.4.3.8 Message contents exceptions (network signalled value “CA_NS_04")

1. Information element additionalSpectrumEmission is set to CA_NS_04. This can be set in the RadioResourceConfigCommonSCell-r10-DEFAULT as part of the common RRC messages. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.6.3.3A.1.4.3.8-1: RadioResourceConfigCommonSCell-r10-DEFAULT: Additional spectrum emission test requirement for “CA_NS_04”

Derivation Path: TS 36.508 [7] clause 4.6.3, Table 4.6.3-13A
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmissionSCell-r10	4 (CA_NS_04)

6.6.3.3A.1.5 Test requirement

This clause specifies the requirements for the specified E-UTRA band for an additional spectrum emission for CA requirement with protected bands as indicated from table 6.6.3.3A.1.5.1-1 to table 6.6.3.3A.1.5.6-1.

6.6.3.3A.1.5.1 Test requirement for CA (network signalled value "CA_NS_01")

When "CA_NS_01" is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4A.1.5-1 as appropriate,

and

the measured average power of spurious emission, derived in step 2, shall not exceed the described value in Table 6.6.3.3A.1.5.1-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1A.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3A.1.5.1-1: Additional requirements (PHS) for CA

Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Note
E-UTRA band 34	F_{DL_low}	–	F_{DL_high}	-50	1
Frequency range	1884.5	–	1915.7	-41	0.3	1
Note 1: Applicable when the aggregated channel bandwidth is confined within frequency range 1940 – 1980 MHz.

6.6.3.3A.1.5.2 Test requirement for CA (network signalled value “CA_NS_02")

When “CA_NS_02” is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4A.1.5-2 as appropriate,

and

the measured average power of spurious emission, derived in step 2, shall not exceed the described value in Table 6.6.3.3A.1.5.2-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1A.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3A.1.5.2-1: Additional requirements for CA

Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)
E-UTRA band 34	F_{DL_low}	–	F_{DL_high}	-50	1
Frequency range	1900	–	1915	-15.5	5
Frequency range	1915	–	1920	+1.6	5

6.6.3.3A.1.5.3 Test requirement for CA (network signalled value “CA_NS_03")

When “CA_NS_03” is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4A.1.5-3 as appropriate,

and

the measured average power of spurious emission, derived in step 2, shall not exceed the described value in Table 6.6.3.3A.1.5.3-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1A.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3A.1.5.3-1: Additional requirement for CA

Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)
E-UTRA band 34	F_{DL_low}	–	F_{DL_high}	-50	1
Frequency range	1880	–	1895	-40	1
Frequency range	1895	–	1915	-15.5	5
Frequency range	1915	–	1920	+1.6	5

6.6.3.3A.1.5.4 Test requirement for CA (network signalled value “CA_NS_05")

When “CA_NS_05” is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4A.1.5-5 as appropriate,

and

the measured average power of spurious emission, derived in step 2, shall not exceed the described value in Table 6.6.3.3A.1.5.4-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1A.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3A.1.5.4-1: Additional requirement for CA

Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)
Frequency range	2620	–	2645	-15.5	5
Frequency range	2645	–	2690	-40	1

6.6.3.3A.1.5.5 Test requirement for CA (network signalled value “CA_NS_06")

When “CA_NS_06” is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4A.1.5-6 as appropriate,

and

the measured average power of spurious emission, derived in step 2, shall not exceed the described value in Table 6.6.3.3A.1.5.5-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1A.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3A.1.5.5-1: Additional requirements

Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)
Frequency range	2570	–	2575	+1.6	5
Frequency range	2575	–	2595	-15.5	5
Frequency range	2595	–	2620	-40	1

6.6.3.3A.1.5.6 Test requirement for CA (network signalled value “CA_NS_07")

When “CA_NS_07” is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4A.1.5-7 as appropriate,

and

the measured average power of spurious emission, derived in step 2, shall not exceed the described value in Table 6.6.3.3A.1.5.6-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1A.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3A.1.5.6-1: Additional requirement for CA

Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
Frequency range	1805	–	1855	-40	1	1
Frequency range	1855	–	1880	-15.5	5	1, 2, 3
NOTE 1: This requirement is applicable for carriers with aggregated channel bandwidths confined in 1885-1920 MHz NOTE 2: The requirement also applies for the frequency ranges that are less than FOOB (MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.0-1 from the edge of the channel bandwidth. NOTE 3: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band.

6.6.3.3A.1.5.7 Test requirement for CA (network signalled value “CA_NS_08")

FFS

6.6.3.3A.1.5.8 Test requirement for CA (network signalled value “CA_NS_04")

When “CA_NS_04” is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4A.1.5-4 as appropriate,

and

the measured average power of spurious emission, derived in step 2, shall not exceed the described value in Table 6.6.3.3A.1.5.8-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1A.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3A.1.5.8-1: Additional requirement for CA

Frequency band	Spectrum emission limit (dBm)	Measurement bandwidth
2490.5 MHz ≤ f < 2495 MHz	-13	1 MHz
9 kHz < f < 2490.5 MHz	-25	1 MHz

6.6.3.3A.1_1 Additional spurious emissions for CA (intra-band contiguous DL CA and UL CA) for UL 64QAM

Editor’s note: For a transition period until RAN5#83, this test case in version 15.3.1 of 36.521-1 shall be used. This is to ensure no test coverage is lost before the UL 256QAM test case becomes available.

6.6.3.3A.1_1.1 Test purpose

Same test purpose as in clause 6.6.3.3A.1.1

6.6.3.3A.1_1.2 Test applicability

This test case applies to all types of E-UTRA UE from release 13 and forward that support intra-band contiguous DL CA, UL CA and UL 64QAM but do not support UL 256QAM.

6.6.3.3A.1_1.3 Minimum conformance requirements

Same minimum conformance requirements as in clause 6.6.3.3.3A.1.3

6.6.3.3A.1_1.4 Test description

6.6.3.3A.1_1.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and CC combinations based on E-UTRA CA configurations specified in table 5.4.2A.1-1. All of these configurations shall be tested with applicable test parameters for each CA Configuration, and are shown in tables’ 6.6.3.3A.1_1.4.1-1 to 6.6.3.3A.1_1.4.1-3. The details of the uplink reference measurement channels (RMCs) are specified in Annexes A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.3A.1_1.4.1-1: Test Configuration Table for CA (network signalled value “CA_NS_01”)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						Lowest N_{RB_agg}Highest N_{RB_agg}
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	64QAM	1		P_1@0	S_0@0
2	75	75		64QAM	150		P_75@0	S_75@0
3	75	75		64QAM	45		P_45@7	S_0@0
4	75	75		64QAM	8		P_0@0	S_8@67
5	75	75		64QAM	129		P_75@0	S_54@0
6	75	75		64QAM	2		P_1@0	S_1@74
7	100	100		64QAM	200		P_100@0	S_100@0
8	100	100		64QAM	1		P_1@0	S_0@0
9	100	100		64QAM	175		P_75@25	S_100@0
10	100	100		64QAM	25		P_0@0	S_25@75
11	100	100		64QAM	64		P_64@24	S_0@0
12	100	100		64QAM	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

Table 6.6.3.3A.1_1.4.1-2: Test Configuration Table for CA (network signalled value "CA_NS_02")

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						Lowest N_{RB_agg} Highest N_{RB_agg}
Test Parameters for CA Configurations
ID	CA Configuration / NR_{B_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	64QAM	1		P_1@0	S_0@0
2	75	75		64QAM	75		P_75@0	S_0@0
3	75	75		64QAM	129		P_75@0	S_54@0
4	75	75		64QAM	129		P_54@21	S_75@0
5	75	75		64QAM	1		P_0@0	S_1@74
6	75	75		64QAM	1		P_0@0	S_1@54
7	75	75		64QAM	2		P_1@0	S_1@74
8	100	100		64QAM	1		P_1@0	S_0@0
9	100	100		64QAM	1		P_1@21	S_0@0
10	100	100		64QAM	90		P_90@0	S_0@0
11	100	100		64QAM	180		P_100@0	S_80@0
12	100	100		64QAM	1		P_0@0	S_1@99
13	100	100		64QAM	1		P_0@0	S_1@83
14	100	100		64QAM	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

Table 6.6.3.3A.1_1.4.1-3: Test Configuration Table for CA (network signalled value “CA_NS_03”)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						Lowest N_{RB_agg}Highest N_{RB_agg}
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	64QAM	1		P_1@0	S_0@0
2	75	75		64QAM	1		P_1@21	S_0@0
3	75	75		64QAM	75		P_75@0	S_0@0
4	75	75		64QAM	90		P_75@0	S_15@0
5	75	75		64QAM	150		P_75@0	S_75@0
6	75	75		64QAM	1		P_0@0	S_1@74
7	75	75		64QAM	1		P_0@0	S_1@44
8	75	75		64QAM	2		P_1@0	S_1@74
9	100	100		64QAM	1		P_1@0	S_0@0
10	100	100		64QAM	60		P_60@0	S_0@0
11	100	100		64QAM	1		P_1@63	S_0@0
12	100	100		64QAM	90		P_90@0	S_0@0
13	100	100		64QAM	164		P_100@0	S_64@0
14	100	100		64QAM	1		P_0@0	S_1@99
15	100	100		64QAM	1		P_0@0	S_1@70
16	100	100		64QAM	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

Table 6.6.3.3A.1_1.4.1-4: Test Configuration Table for CA (network signalled value “CA_NS_05”)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						Lowest N_{RB_agg}Highest N_{RB_agg}
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	64QAM	40		P_40@0	S_0@0
2	75	75		64QAM	80		P_50@25	S_30@0
3	75	75		64QAM	60		P_10@65	S_50@0
4	75	75		64QAM	65		P_1@74	S_64@0
5	75	75		64QAM	92		P_20@55	S_72@0
6	75	75		64QAM	2		P_1@0	S_1@74
7	100	100		64QAM	8		P_8@0	S_0@0
8	100	100		64QAM	40		P_40@0	S_0@0
9	100	100		64QAM	80		P_50@50	S_30@0
10	100	100		64QAM	150		P_60@40	S_90@0
11	100	100		64QAM	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

Table 6.6.3.3A.1_1.4.1-5: Test Configuration Table (network signalled value "CA_NS_06")

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						As in Table 6.2.4A.1_1.3.6-1
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	64QAM	5		P_5@0	S_0@0
2	75	75		64QAM	45		P_45@0	S_0@0
3	75	75		64QAM	75		P_60@15	S_15@0
4	75	75		64QAM	60		P_10@65	S_50@0
5	75	75		64QAM	90		P_18@57	S_72@0
6	75	75		64QAM	2		P_1@0	S_1@74
7	100	100		64QAM	10		P_10@0	S_0@0
8	100	100		64QAM	30		P_30@0	S_0@0
9	100	100		64QAM	100		P_75@25	S_25@0
10	100	100		64QAM	90		P_40@60	S_50@0
11	100	100		64QAM	96		P_15@85	S_81@0
12	100	100		64QAM	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1.

Table 6.6.3.3A.1_1.4.1-6: Test Configuration Table for CA (network signalled value “CA_NS_07”)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						As in Table 6.2.4A.1_1.3.7-1
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	100	25	N/A	64QAM	1		P_1@0	S_0@0
2	100	25		64QAM	85		P_80@20	S_5@0
3	100	25		64QAM	65		P_60@40	S_5@0
4	100	25		64QAM	35		P_30@70	S_5@0
5	100	25		64QAM	2		P_1@0	S_1@24
6	100	50		64QAM	1		P_1@1	S_0@0
7	100	50		64QAM	10		P_10@30	S_0@0
8	100	50		64QAM	30		P_30@30	S_0@0
9	100	50		64QAM	60		P_40@60	S_20@0
10	100	50		64QAM	30		P_10@90	S_20@0
11	100	50		64QAM	5		P_0@0	S_5@45
12	100	50		64QAM	2		P_1@0	S_1@49
13	100	75		64QAM	1		P_1@1	S_0@0
14	100	75		64QAM	40		P_40@20	S_0@0
15	100	75		64QAM	85		P_80@20	S_5@0
16	100	75		64QAM	40		P_0@0	S_40@20
17	100	75		64QAM	15		P_0@0	S_15@60
18	100	75		64QAM	2		P_1@0	S_1@74
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

Table 6.6.3.3A.1_1.4.1-8: Test Configuration Table for CA (network signalled value “CA_NS_04”)

Initial Conditions
Test Environment as specified in TS 36.508 [7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						As in Table 6.2.4A.1_1.3.4-1
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	100	50	N/A	64QAM	10		P_10@20	S_0@0
2	100	50		64QAM	60		P_50@50	S_10@0
3	100	50		64QAM	15		P_0@0	S_15@0
4	100	50		64QAM	2		P_1@0	S_1@49
5	75	75		64QAM	10		P_10@20	S_0@0
6	75	75		64QAM	75		P_30@45	S_45@0
7	75	75		64QAM	2		P_1@0	S_1@74
8	100	75		64QAM	10		P_10@20	S_0@0
9	100	75		64QAM	80		P_50@50	S_30@0
10	100	75		64QAM	20		P_0@0	S_20@15
11	100	75		64QAM	2		P_1@0	S_1@74
12	100	100		64QAM	10		P_10@25	S_0@0
13	100	100		64QAM	90		P_40@60	S_50@0
14	100	100		64QAM	15		P_0@0	S_15@40
15	100	100		64QAM	20		P_0@0	S_20@30
16	100	100		64QAM	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1.

1. Connect the SS to the UE to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure group A.33 as appropriate.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals for PCC are initially set up according to Annex C.0, C.1 and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Table 6.6.3.3A.1_1.4.1-1, Table 6.6.3.3A.1_1.4.1-2, Table 6.6.3.3A.1_1.4.1-3, Table 6.6.3.3A.1_1.4.1-4, Table 6.6.3.3A.1_1.4.1-5 or Table 6.6.3.3A.1_1.4.1-6 depending on network signal value.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.3A.1_1.4.3.

6.6.3.3A.1_1.4.2 Test procedure

Same test procedure as in clause 6.6.3.3A.1.4.2 with following exceptions:

– In step 2: Instead of clause 6.6.3.3A.1.4.3  use clause 6.6.3.3A.1_1.4.3.

– In step 4: Instead of Table 6.6.3.3A.1.4.1-1, Table 6.6.3.3A.1.4.1-2, Table 6.6.3.3A.1.4.1-3, Table 6.6.3.3A.1.4.1-4, Table 6.6.3.3A.1.4.1-5 or Table 6.6.3.3A.1.4.1-6  use Table 6.6.3.3A.1_1.4.1-1, Table 6.6.3.3A.1_1.4.1-2, Table 6.6.3.3A.1_1.4.1-3, Table 6.6.3.3A.1_1.4.1-4, Table 6.6.3.3A.1_1.4.1-5 or Table 6.6.3.3A.1_1.4.1-6.

– In step 6: Instead of Tables 6.2.4A.1.5-1 to 6.2.4A.1.5-7  use Tables 6.2.4A.1_1.5-1 to 6.2.4A.1_1.5-7.

6.6.3.3A.1_1.4.3 Message contents

Same message contents as in clause 6.6.3.3A.1.4.3.

6.6.3.3A.1_1.5 Test requirement

Same test requirements as in clause 6.6.3.3A.1.5 with following exceptions:

– Instead of Tables 6.2.4A.1.5-1 to 6.2.4A.1.5-7  use Tables 6.2.4A.1_1.5-1 to 6.2.4A.1_1.5-7.

6.6.3.3A.1_2 Additional spurious emissions for CA (intra-band contiguous DL CA and UL CA) for UL 256QAM

6.6.3.3A.1_2.1 Test purpose

Same test purpose as in clause 6.6.3.3A.1.1

6.6.3.3A.1_2.2 Test applicability

This test case applies to all types of E-UTRA UE from release 14 and forward that support intra-band contiguous DL CA, UL CA and UL 256QAM.

6.6.3.3A.1_2.3 Minimum conformance requirements

Same minimum conformance requirements as in clause 6.6.3.3A.1.3

6.6.3.3A.1_2.4 Test description

6.6.3.3A.1_2.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and CC combinations based on E-UTRA CA configurations specified in table 5.4.2A.1-1. All of these configurations shall be tested with applicable test parameters for each CA Configuration, and are shown in tables 6.6.3.3A.1_2.4.1-1 to 6.6.3.3A.1_2.4.1-6. The details of the uplink reference measurement channels (RMCs) are specified in Annexes A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.3A.1_2.4.1-1: Test Configuration Table for CA (network signalled value “CA_NS_01”)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						Lowest N_{RB_agg}Highest N_{RB_agg}
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	256QAM	1		P_1@0	S_0@0
2	75	75		256QAM	150		P_75@0	S_75@0
3	75	75		256QAM	45		P_45@7	S_0@0
4	75	75		256QAM	8		P_0@0	S_8@67
5	75	75		256QAM	129		P_75@0	S_54@0
6	75	75		256QAM	2		P_1@0	S_1@74
7	100	100		256QAM	200		P_100@0	S_100@0
8	100	100		256QAM	1		P_1@0	S_0@0
9	100	100		256QAM	175		P_75@25	S_100@0
10	100	100		256QAM	25		P_0@0	S_25@75
11	100	100		256QAM	64		P_64@24	S_0@0
12	100	100		256QAM	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

Table 6.6.3.3A.1_2.4.1-2: Test Configuration Table for CA (network signalled value "CA_NS_02")

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						Lowest N_{RB_agg} Highest N_{RB_agg}
Test Parameters for CA Configurations
ID	CA Configuration / NR_{B_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	256QAM	1		P_1@0	S_0@0
2	75	75		256QAM	75		P_75@0	S_0@0
3	75	75		256QAM	129		P_75@0	S_54@0
4	75	75		256QAM	129		P_54@21	S_75@0
5	75	75		256QAM	1		P_0@0	S_1@74
6	75	75		256QAM	1		P_0@0	S_1@54
7	75	75		256QAM	2		P_1@0	S_1@74
8	100	100		256QAM	1		P_1@0	S_0@0
9	100	100		256QAM	1		P_1@21	S_0@0
10	100	100		256QAM	90		P_90@0	S_0@0
11	100	100		256QAM	180		P_100@0	S_80@0
12	100	100		256QAM	1		P_0@0	S_1@99
13	100	100		256QAM	1		P_0@0	S_1@83
14	100	100		256QAM	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

Table 6.6.3.3A.1_2.4.1-3: Test Configuration Table for CA (network signalled value “CA_NS_03”)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						Lowest N_{RB_agg}Highest N_{RB_agg}
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	256QAM	1		P_1@0	S_0@0
2	75	75		256QAM	1		P_1@21	S_0@0
3	75	75		256QAM	75		P_75@0	S_0@0
4	75	75		256QAM	90		P_75@0	S_15@0
5	75	75		256QAM	150		P_75@0	S_75@0
6	75	75		256QAM	1		P_0@0	S_1@74
7	75	75		256QAM	1		P_0@0	S_1@44
8	75	75		256QAM	2		P_1@0	S_1@74
9	100	100		256QAM	1		P_1@0	S_0@0
10	100	100		256QAM	60		P_60@0	S_0@0
11	100	100		256QAM	1		P_1@63	S_0@0
12	100	100		256QAM	90		P_90@0	S_0@0
13	100	100		256QAM	164		P_100@0	S_64@0
14	100	100		256QAM	1		P_0@0	S_1@99
15	100	100		256QAM	1		P_0@0	S_1@70
16	100	100		256QAM	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

Table 6.6.3.3A.1_2.4.1-4: Test Configuration Table for CA (network signalled value “CA_NS_05”)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						Lowest N_{RB_agg}Highest N_{RB_agg}
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	256QAM	40		P_40@0	S_0@0
2	75	75		256QAM	80		P_50@25	S_30@0
3	75	75		256QAM	60		P_10@65	S_50@0
4	75	75		256QAM	65		P_1@74	S_64@0
5	75	75		256QAM	92		P_20@55	S_72@0
6	75	75		256QAM	2		P_1@0	S_1@74
7	100	100		256QAM	8		P_8@0	S_0@0
8	100	100		256QAM	40		P_40@0	S_0@0
9	100	100		256QAM	80		P_50@50	S_30@0
10	100	100		256QAM	150		P_60@40	S_90@0
11	100	100		256QAM	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

Table 6.6.3.3A.1_2.4.1-5: Test Configuration Table (network signalled value "CA_NS_06")

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						As in Table 6.2.4A.1_2.3.6-1
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	75	75	N/A	256QAM	5		P_5@0	S_0@0
2	75	75		256QAM	45		P_45@0	S_0@0
3	75	75		256QAM	75		P_60@15	S_15@0
4	75	75		256QAM	60		P_10@65	S_50@0
5	75	75		256QAM	90		P_18@57	S_72@0
6	75	75		256QAM	2		P_1@0	S_1@74
7	100	100		256QAM	10		P_10@0	S_0@0
8	100	100		256QAM	30		P_30@0	S_0@0
9	100	100		256QAM	100		P_75@25	S_25@0
10	100	100		256QAM	90		P_40@60	S_50@0
11	100	100		256QAM	96		P_15@85	S_81@0
12	100	100		256QAM	2		P_1@0	S_1@99
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1.

Table 6.6.3.3A.1_2.4.1-6: Test Configuration Table for CA (network signalled value “CA_NS_07”)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 for different CA bandwidth classes, and PCC and SCCs are mapped onto physical frequencies according to Table 6.1-2.						C: Low and High range
Test CC Combination setting (N_{RB_agg}) as specified in subclause 5.4.2A.1 for the CA Configuration						As in Table 6.2.4A.1_2.3.7-1
Test Parameters for CA Configurations
ID	CA Configuration / N_{RB_agg}		DL Allocation (PDCCH on PCC)	CC MOD	UL Allocation
ID	PCC N_RB	SCCs N_RB	PCC & SCC RB allocation	CC MOD	N_{RB_alloc}		PCC & SCC RB allocations (L_CRB @ RB_start)
1	100	25	N/A	256QAM	1		P_1@0	S_0@0
2	100	25		256QAM	85		P_80@20	S_5@0
3	100	25		256QAM	65		P_60@40	S_5@0
4	100	25		256QAM	35		P_30@70	S_5@0
5	100	25		256QAM	2		P_1@0	S_1@24
6	100	50		256QAM	1		P_1@1	S_0@0
7	100	50		256QAM	10		P_10@30	S_0@0
8	100	50		256QAM	30		P_30@30	S_0@0
9	100	50		256QAM	60		P_40@60	S_20@0
10	100	50		256QAM	30		P_10@90	S_20@0
11	100	50		256QAM	5		P_0@0	S_5@45
12	100	50		256QAM	2		P_1@0	S_1@49
13	100	75		256QAM	1		P_1@1	S_0@0
14	100	75		256QAM	40		P_40@20	S_0@0
15	100	75		256QAM	85		P_80@20	S_5@0
16	100	75		256QAM	40		P_0@0	S_40@20
17	100	75		256QAM	15		P_0@0	S_15@60
18	100	75		256QAM	2		P_1@0	S_1@74
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1

1. Connect the SS to the UE to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure group A.33 as appropriate.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals for PCC are initially set up according to Annex C.0, C.1 and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Table 6.6.3.3A.1_2.4.1-1, Table 6.6.3.3A.1_2.4.1-2, Table 6.6.3.3A.1_2.4.1-3, Table 6.6.3.3A.1_2.4.1-4, Table 6.6.3.3A.1_2.4.1-5 or Table 6.6.3.3A.1_2.4.1-6 depending on network signal value.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.3A.1_2.4.3.

6.6.3.3A.1_2.4.2 Test procedure

Same test procedure as in clause 6.6.3.3A.1.4.2 with following exceptions:

– Instead of Tables 6.2.4A.1.5-1 to 6.2.4A.1.5-7  use Tables 6.2.4A.1_2.5-1 to 6.2.4A.1_2.5-7.

6.6.3.3A.1_2.4.3 Message contents

Same message contents as in clause 6.6.3.3A.1.4.3.

6.6.3.3A.1_2.5 Test requirement

Same test requirements as in clause 6.6.3.3A.1.5.1 with following exceptions:

– Instead of Tables 6.2.4A.1.5-1 to 6.2.4A.1.5-7  use Tables 6.2.4A.1_2.5-1 to 6.2.4A.1_2.5-7.

6.6.3.3A.2 Additional spurious emissions for CA (inter-band DL CA and UL CA)

6.6.3.3A.2.1 Test purpose

To verify that UE transmitter does not cause unacceptable interference to other channels or other systems in terms of transmitter spurious emissions in inter-band carrier aggregation under the deployment scenarios where additional requirements are specified.

6.6.3.3A.2.2 Test applicability

This test case applies to all types of E-UTRA UE release 11 and forward that support inter-band DL CA and UL CA but do not support UL 64QAM or UL 256QAM.

6.6.3.3A.2.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.3.3.

6.6.3.3A.2.4 Test description

6.6.3.3A.2.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state. For the UE maximum output power modified by A-MPR specified in table 6.6.3.3A.2.4.1-1, the power limits specified in subclause 6.2.5A.2.3 apply.

Table 6.6.3.3A.2.4.1-1: Additional spurious emissions for inter-band CA

Uplink CA Configuration	NS-value per CC (in same order as UL CA Configuration column)		Applicable emissions requirements (in same order as UL CA Configuration column)
CA_1A-3A^{Note 3} CA_1A-5A^{Note 3} CA_1A-7A^{Note 3} CA_1A-8A^{Note 3} CA_1A-18A^{Note 3} CA_1A-26A^{Note 3} CA_1A-42A^{Note 3}	NS_05	NS_01	Table 6.6.3.3.5.2-1	N/A
CA_1A-19A^{Note 3}	NS_05	NS_08	Table 6.6.3.3.5.2-1	Table 6.6.3.3.5.4-1
CA_1A-21A^{Note 3}	NS_05	NS_09	Table 6.6.3.3.5.2-1	Table 6.6.3.3.5.5-1
CA_2A-4A CA_2A-66A	NS_03	NS_03	N/A	N/A
CA_2A-12A CA_2A-13A CA_4A-12A CA_4A-13A CA_4A-17A	NS_03	NS_06	N/A	N/A
CA_2A-13A^{Note 3}, CA_4A-13A^{Note 3}	NS_03	NS_07	N/A	Table 6.6.3.3.5.3-1
CA_2A-30A^{Note 3}	NS_03	NS_21	N/A	Table 6.6.3.3.5.16-1
CA_2A-46A	NS_03	NS_28	N/A	Table 6.6.3.3.3.22-1
CA_2A-46A	NS_03	NS_29	N/A	Table 6.6.3.3.3.23-1
CA_2A-46A	NS_03	NS_30	N/A	Table 6.6.3.3.3.24-1 Table 6.6.3.3.3.24-2 Table 6.6.3.3.3.24-3
CA_2A-46A	NS_03	NS_31	N/A	Table 6.6.3.3.3.25-1 Table 6.6.3.3.3.25-2 Table 6.6.3.3.3.25-3 Table 6.6.3.3.3.25-4
CA_3A-5A CA_3A-7A CA_3A-8A CA_5A-7A	NS_01	NS_01	N/A	N/A
CA_3A-19A^{Note 3}	NS_01	NS_08	N/A	Table 6.6.3.3.5.4-1
CA_3A-20A CA_7A-20A	NS_01	NS_10	N/A	N/A
CA_3A-26A	NS_01	NS_12	N/A	Table 6.6.3.3.5.7-1
CA_3A-26A	NS_01	NS_13	N/A	Table 6.6.3.3.3.8-1
CA_3A-26A	NS_01	NS_14	N/A	Table 6.6.3.3.3.9-1
CA_3A-26A	NS_01	NS_15	N/A	Table 6.6.3.3.5.10-1
CA_2A-5A CA_2A-7ACA_4A-5A CA_4A-7A	NS_03	NS_01	N/A	N/A
CA_5A-12A CA_5A-17A	NS_01	NS_06	N/A	N/A
CA_5A-30A^{Note 3}	NS_01	NS_21	N/A	Table 6.6.3.3.5.16-1
CA_5A-66A	NS_01	NS_03	N/A	N/A
CA_7A-28A^{Note 3}	NS_01	NS_17	N/A	Table 6.6.3.3.5.12-1
CA_7A-28A^{Note 3}	NS_01	NS_18	N/A	Table 6.6.3.3.5.13-1
CA_19A-21A^{Note 3}	NS_08	NS_09	Table 6.6.3.3.5.4-1	Table 6.6.3.3.5.5-1
CA_1A-28A^{Note 3}	NS_05	NS_17	Table 6.6.3.3.5.2-1	Table 6.6.3.3.5.12-1
CA_12A-30A^{Note 3}	NS_06	NS_21	N/A	Table 6.6.3.3.5.16-1
CA_18A-28A	NS_01	NS_17	N/A	Table 6.6.3.3.5.12-1
Note 1: For CCs with NS_01, there are no additional requirements defined in 36.101. Only CCs with NS-value different than NS_01 and present in 6.6.3.3.3 needs to be tested. Note 2: A-MPR values for NS-values in this table are the same as in section 6.2.4.3. Note 3: No test required since the frequency range to test is unaffected by intermodulation products as described in section 4.3 in TR 36.905.

The initial test configurations consist of environmental conditions, test frequencies, and CC combinations based on E‑UTRA CA configurations specified in table 5.4.2A.1-2. All of these configurations shall be tested with applicable test parameters for each CA Configuration, and are shown in tables 6.6.3.3A.2.4.1-2 to 6.6.3.3A.2.4.1-9. The details of the uplink reference measurement channels (RMCs) are specified in Annexe A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.3A.2.4.1-2: Test Configuration Table (network signalled value NS_01/NS_12)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Low and High range for both PCC and SCC (Note 3)
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg(Note 2)
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_01)	SCC (NS_12)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations (L_CRB @ RB_start)
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations (L_CRB @ RB_start)
1	25	25	N/A for this test	QPSK	QPSK	8	8@7
2	25	25		16QAM	16QAM	10	8
3	25	25		QPSK	16QAM	8	8
4	50	50		QPSK	QPSK	12	12@16
5	50	50		16QAM	16QAM	15	18
6	50	50		QPSK	16QAM	12	18
7	100	75		QPSK	QPSK	15	16@31
8	100	75		16QAM	16QAM	20	30
9	100	75		QPSK	16QAM	15	30
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1. Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same NRB_agg. Only the combination with the highest NRB_PCC is tested. Note 3: For Low range place test point with RBstart=0. For High range place test point with RB_start=RB_end-L_CRB+1.

Table 6.6.3.3A.2.4.1-3: Test Configuration Table (network signalled value NS_01/NS_15)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Low and High range for both PCC and SCC (Note 3)
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg(Note 2)
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_01)	SCC (NS_15)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations (L_CRB @ RB_start)
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations (L_CRB @ RB_start)
1	25	25	N/A for this test	QPSK	QPSK	8	6@14
2	25	25		16QAM	16QAM	10	10@15
3	25	25		QPSK	16QAM	8	10@15
4	50	50		QPSK	QPSK	12	12@25
5	50	50		16QAM	16QAM	15	15@35
6	50	50		QPSK	16QAM	12	15@35
7	100	75		QPSK	QPSK	18	18@19
8	100	75		16QAM	16QAM	20	20@55
9	100	75		QPSK	16QAM	18	20@55
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1. Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same NRB_agg. Only the combination with the highest NRB_PCC is tested. Note 3: For Low range place test point with RBstart=0. For High range place test point with RB_start=RB_end-L_CRB+1.

Table 6.6.3.3A.2.4.1-4: Test Configuration Table (network signalled value NS_01/NS_17)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Low and High range for both PCC and SCC (Note 3)
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg(Note 2)
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_01)	SCC (NS_17)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
1	25	25	N/A for this test	QPSK	QPSK	6	6
2	25	25		16QAM	16QAM	25	25
3	25	25		16QAM	QPSK	25	6
4	25	50		QPSK	QPSK	6	12
5	25	50		16QAM	16QAM	25	25
6	25	50		16QAM	QPSK	25	12
7	50	50		QPSK	QPSK	12	12
8	50	50		16QAM	16QAM	50	25
9	50	50		16QAM	QPSK	50	12
10	100	50		QPSK	QPSK	16	12
11	100	50		16QAM	16QAM	50	25
12	100	50		16QAM	QPSK	50	12
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1 Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same NRB_agg. Only the combination with the highest NRB_PCC is tested. Note 3: For Low range place test point with RBstart=0. For High range place test point with RB_start=RB_end-L_CRB+1.

Table 6.6.3.3A.2.4.1-5: Test Configuration Table (network signalled value NS_05/NS_01)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Low range, Mid range for PCC In case of Low range: – For 5MHz Channel Bandwidth: 1927.2MHz (NUL = 18072) – For 10 MHz Channel Bandwidth: 1934.7 MHz (NUL = 18147) – For 20 MHz Channel Bandwidth: 1930 MHz (NUL = 18100) Mid range for SCC(Note 3)
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg(Note 2)
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_05)	SCC (NS_01)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
1	25	15	N/A for this test	QPSK	QPSK	6	4
2	25	15		16QAM	16QAM	25	6
3	25	15		16QAM	QPSK	25	4
4	25	25		QPSK	QPSK	6	6
5	25	25		16QAM	16QAM	25	25
6	25	25		16QAM	QPSK	25	6
7	25	50		QPSK	QPSK	6	12
8	25	50		16QAM	16QAM	25	25
9	25	50		16QAM	QPSK	25	12
10	50	50		QPSK	QPSK	12	12
11	50	50		16QAM	16QAM	50	25
12	50	50		16QAM	QPSK	50	12
13	100	50		QPSK	QPSK	18	12
14	100	50		16QAM	16QAM	50	25
15	100	50		16QAM	QPSK	50	12
16	100	75		QPSK	QPSK	18	16
17	100	75		16QAM	16QAM	50	25
18	100	75		16QAM	QPSK	50	16
19	100	100		QPSK	QPSK	18	18
20	100	100		16QAM	16QAM	50	25
21	100	100		16QAM	QPSK	50	18
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1 Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same NRB_agg. Only the combination with the highest NRB_PCC is tested. Note 3: For Low range place test point with RBstart=0. For Mid range place test point with RB_start=RB_end-L_CRB+1.

Table 6.6.3.3A.2.4.1-6: Test Configuration Table (network signalled value NS_03/NS_28)

Initial Conditions
Test Environment as specified in TS 36.508 [7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Mid range for PCC. For SCC a. 5340 MHz for config ID 1-4 b. 5520 MHz for config ID 5-8
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_06)	SCC (NS_21)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
1	25	100	N/A for this test	QPSK	QPSK	6	L=1
2	25	100		16QAM	16QAM	25	L=10
3	100	100		QPSK	QPSK	10	L=1
4	100	100		16QAM	16QAM	100	L=10
5	25	100		QPSK	QPSK	6	L=1
6	25	100		16QAM	16QAM	25	L=10
7	100	100		QPSK	QPSK	10	L=1
8	100	100		16QAM	16QAM	100	L=10
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-2. Note 2: For simplifying test, PCC is mapped to the first band of the combination as listed in Uplink CA Configuration column in Table 6.2.4A.2.4.1-1. Note 3: For partial RB allocation unless RBstart is explicitly defined, for Low range place test point with RBstart=0, for High range place test point with RB_start=RB_end-L_CRB+1.

Table 6.6.3.3A.2.4.1-7: Test Configuration Table (network signalled value NS_03/NS_29)

Initial Conditions
Test Environment as specified in TS 36.508 [7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Mid range for PCC. For SCC, for configuration ID: a. 5180 MHz for config ID 1-4 b. 5240 MHz for config ID 5-8 c. 5260 MHz for config ID 9-12 d. 5320 MHz for config ID 13-16 e. 5500 MHz for config ID 17-20 f. 5700 MHz for config ID 21-24
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_06)	SCC (NS_21)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
1	25	100	N/A for this test	QPSK	QPSK	6	L=1
2	25	100		16QAM	16QAM	25	L=10
3	100	100		QPSK	QPSK	10	L=1
4	100	100		16QAM	16QAM	100	L=10
5	25	100		QPSK	QPSK	6	L=1
6	25	100		16QAM	16QAM	25	L=10
7	100	100		QPSK	QPSK	10	L=1
8	100	100		16QAM	16QAM	100	L=10
9	25	100		QPSK	QPSK	6	L=1
10	25	100		16QAM	16QAM	25	L=10
11	100	100		QPSK	QPSK	10	L=1
12	100	100		16QAM	16QAM	100	L=10
13	25	100		QPSK	QPSK	6	L=1
14	25	100		16QAM	16QAM	25	L=10
15	100	100		QPSK	QPSK	10	L=1
16	100	100		16QAM	16QAM	100	L=10
17	25	100		QPSK	QPSK	6	L=1
18	25	100		16QAM	16QAM	25	L=10
19	100	100		QPSK	QPSK	10	L=1
20	100	100		16QAM	16QAM	100	L=10
21	25	100		QPSK	QPSK	6	L=1
22	25	100		16QAM	16QAM	25	L=10
23	100	100		QPSK	QPSK	10	L=1
24	100	100		16QAM	16QAM	100	L=10
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-2. Note 2: For simplifying test, PCC is mapped to the first band of the combination as listed in Uplink CA Configuration column in Table 6.2.4A.2.4.1-1. Note 3: For partial RB allocation unless RBstart is explicitly defined, for Low range place test point with RBstart=0, for High range place test point with RB_start=RB_end-L_CRB+1.

Table 6.6.3.3A.2.4.1-8: Test Configuration Table (network signalled value NS_03/NS_30)

Initial Conditions
Test Environment as specified in TS 36.508 [7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Low and High range for PCC. For SCC, for configuration ID: a. 5160 MHz for config ID 1-4 b. 5320 MHz for config ID 5-8 c. 5480 MHz for config ID 9-12 d. 5700 MHz for config ID 13-16 e. 5180 MHz for config ID 17-20
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_06)	SCC (NS_21)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
1	25	100	N/A for this test	QPSK	QPSK	6	L=1
2	25	100		16QAM	16QAM	25	L=10
3	100	100		QPSK	QPSK	10	L=1
4	100	100		16QAM	16QAM	100	L=10
5	25	100		QPSK	QPSK	6	L=1
6	25	100		16QAM	16QAM	25	L=10
7	100	100		QPSK	QPSK	10	L=1
8	100	100		16QAM	16QAM	100	L=10
9	25	100		QPSK	QPSK	6	L=1
10	25	100		16QAM	16QAM	25	L=10
11	100	100		QPSK	QPSK	10	L=1
12	100	100		16QAM	16QAM	100	L=10
13	25	100		QPSK	QPSK	6	L=1
14	25	100		16QAM	16QAM	25	L=10
15	100	100		QPSK	QPSK	10	L=1
16	100	100		16QAM	16QAM	100	L=10
17	25	100		QPSK	QPSK	6	L=1
18	25	100		16QAM	16QAM	25	L=10
19	100	100		QPSK	QPSK	10	L=1
20	100	100		16QAM	16QAM	100	L=10
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-2. Note 2: For simplifying test, PCC is mapped to the first band of the combination as listed in Uplink CA Configuration column in Table 6.2.4A.2.4.1-1. Note 3: For partial RB allocation unless RBstart is explicitly defined, for Low range place test point with RBstart=0, for High range place test point with RB_start=RB_end-L_CRB+1.

Table 6.6.3.3A.2.4.1-9: Test Configuration Table (network signalled value NS_03/NS_31)

Initial Conditions
Test Environment as specified in TS 36.508 [7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Low and High range for PCC. For SCC, for configuration ID: a. 5160 MHz for config ID 1-4 b. 5260 MHz for config ID 5-8 c. 5700 MHz for config ID 9-12 d. 5745 MHz for config ID 13-16 e. 5600 MHz for config ID 17-20
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_06)	SCC (NS_21)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
1	25	100	N/A for this test	QPSK	QPSK	6	L=1
2	25	100		16QAM	16QAM	25	L=10
3	100	100		QPSK	QPSK	10	L=1
4	100	100		16QAM	16QAM	100	L=10
5	25	100		QPSK	QPSK	6	L=1
6	25	100		16QAM	16QAM	25	L=10
7	100	100		QPSK	QPSK	10	L=1
8	100	100		16QAM	16QAM	100	L=10
9	25	100		QPSK	QPSK	6	L=1
10	25	100		16QAM	16QAM	25	L=10
11	100	100		QPSK	QPSK	10	L=1
12	100	100		16QAM	16QAM	100	L=10
13	25	100		QPSK	QPSK	6	L=1
14	25	100		16QAM	16QAM	25	L=10
15	100	100		QPSK	QPSK	10	L=1
16	100	100		16QAM	16QAM	100	L=10
17	25	100		QPSK	QPSK	6	L=1
18	25	100		16QAM	16QAM	25	L=10
19	100	100		QPSK	QPSK	10	L=1
20	100	100		16QAM	16QAM	100	L=10
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-2. Note 2: For simplifying test, PCC is mapped to the first band of the combination as listed in Uplink CA Configuration column in Table 6.2.4A.2.4.1-1. Note 3: For partial RB allocation unless RBstart is explicitly defined, for Low range place test point with RBstart=0, for High range place test point with RB_start=RB_end-L_CRB+1.

1. Connect the SS to the UE to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure group A.33 as appropriate.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals for PCC are initially set up according to Annex C.0, C.1 and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Tables 6.6.3.3A.2.4.1-2 to 6.6.3.3A.2.4.1-9 depending on network signal value.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.3A.2.4.3.

6.6.3.3A.2.4.2 Test procedures

1. Configure SCC according to Annex C.0, C.1 and Annex C.3.0 for all downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4. Message contents are defined in clause 6.6.3.3A.2.4.3

3. SS activates SCC by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Tables 6.6.3.3A.2.4.1-2 to 6.6.3.3A.2.4.1-9 as appropriate on both PCC and SCC. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

5. Send continuously uplink power control “up” commands in every uplink scheduling information to the UE until the UE transmits at P_UMAX level.

6. Measure the mean power of the UE in the channel bandwidth of the radio access mode according to the test configuration, which shall meet the requirements described in Tables 6.2.4A.2.5-1 to 6.2.4A.2.5-16 as appropriate. The period of the measurement shall be at least one sub-frame (1ms).

7. Measure the power of the transmitted signal with a measurement filter of bandwidths according to Tables 6.6.3.3.5.1-1 to 6.6.3.3.5.24-1 as appropriate. The centre frequency of the filter shall be stepped in contiguous steps according to the same table. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

6.6.3.3A.2.4.3 Message contents

Same message contents as in clause 6.2.4A.2.4.3.

6.6.3.3A.2.5 Test requirement

Same test requirements as in clause 6.6.3.3.5 depending on network signal value.

6.6.3.3A.2_1 Additional spurious emissions for CA (inter-band DL CA and UL CA) for UL 64QAM

6.6.3.3A.2_1.1 Test purpose

6.6.3.3A.2_1.2 Test applicability

This test case applies to all types of E-UTRA UE release 13 and forward that support inter-band DL CA and UL CA and UL 64QAM but do not support UL 256QAM.

6.6.3.3A.2_1.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.3.3.

6.6.3.3A.2_1.4 Test description

6.6.3.3A.2_1.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state. For the UE maximum output power modified by A-MPR specified in table 6.6.3.3A.2_1.4.1-1, the power limits specified in subclause 6.2.5A.2.3 apply.

Table 6.6.3.3A.2_1.4.1-1: Additional spurious emissions for inter-band CA

Uplink CA Configuration	NS-value per CC (in same order as UL CA Configuration column)		Applicable emissions requirements (in same order as UL CA Configuration column)
CA_1A-3A^{Note 3} CA_1A-5A CA_1A-7A CA_1A-8A CA_1A-18A^{Note 3} CA_1A-26A^{Note 3} CA_1A-42A^{Note 3}	NS_05	NS_01	Table 6.6.3.3.5.2-1	N/A
CA_2A-13A, CA_4A-13A	NS_03	NS_07	Table 6.6.2.2.3.1-1	Table 6.6.2.2.3.3-1 Table 6.6.3.3.3.3-1
CA_3A-26A	NS_01	NS_12	N/A	Table 6.6.3.3.3.7-1
CA_3A-26A	NS_01	NS_15	N/A	Table 6.6.3.3.3.10-1
CA_1A-19A^{Note 3}	NS_05	NS_08	Table 6.6.3.3.5.2-1	Table 6.6.3.3.5.4-1
CA_1A-21A^{Note 3}	NS_05	NS_09	Table 6.6.3.3.5.2-1	Table 6.6.3.3.5.5-1
CA_1A-28A^{Note 3}	NS_05	NS_17	Table 6.6.3.3.5.2-1	Table 6.6.3.3.5.12-1
CA_3A-19A^{Note 3}	NS_01	NS_08	N/A	Table 6.6.3.3.5.4-1
CA_19A-21A^{Note 3}	NS_08	NS_09	Table 6.6.3.3.5.4-1	Table 6.6.3.3.5.5-1
CA_18A-28A	NS_01	NS_17	N/A	Table 6.6.3.3.5.12-1
Note 1: For CCs with NS_01, there are no additional requirements defined in 36.101. Only CCs with NS-value different than NS_01 needs to be tested. Note 2: A-MPR values for NS-values in this table are the same as in section 6.2.4.3. Note 3: No test required since only A-Spur requirements apply, and the frequency range to test is unaffected by intermodulation products as described in section 4.3 in TR 36.905.

The initial test configurations consist of environmental conditions, test frequencies, and CC combinations based on E‑UTRA CA configurations specified in table 5.4.2A.1-2. All of these configurations shall be tested with applicable test parameters for each CA Configuration, and are shown in tables 6.6.3.3A.2_1.4.1-2 to 6.6.3.3A.2_1.4.1-5. The details of the uplink reference measurement channels (RMCs) are specified in Annexe A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.3A.2_1.4.1-2: Test Configuration Table (network signalled value NS_01/NS_12)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Low and High range for both PCC and SCC (Note 3)
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg(Note 2)
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_01)	SCC (NS_12)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations (L_CRB @ RB_start)
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations (L_CRB @ RB_start)
1	25	25	N/A for this test	QPSK	QPSK	8	8@7
2	25	25		64QAM	64QAM	10	8
3	25	25		QPSK	64QAM	8	8
4	50	50		QPSK	QPSK	12	12@16
5	50	50		64QAM	64QAM	15	18
6	50	50		QPSK	64QAM	12	18
7	100	75		QPSK	QPSK	15	16@31
8	100	75		64QAM	64QAM	20	30
9	100	75		QPSK	64QAM	15	30
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1. Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same NRB_agg. Only the combination with the highest NRB_PCC is tested. Note 3: For Low range place test point with RBstart=0. For High range place test point with RB_start=RB_end-L_CRB+1.

Table 6.6.3.3A.2_1.4.1-3: Test Configuration Table (network signalled value NS_01/NS_15)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Low and High range for both PCC and SCC (Note 3)
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg(Note 2)
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_01)	SCC (NS_15)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations (L_CRB @ RB_start)
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations (L_CRB @ RB_start)
1	25	25	N/A for this test	QPSK	QPSK	8	6@14
2	25	25		64QAM	64QAM	10	10@15
3	25	25		QPSK	64QAM	8	10@15
4	50	50		QPSK	QPSK	12	12@25
5	50	50		64QAM	64QAM	15	15@35
6	50	50		QPSK	64QAM	12	15@35
7	100	75		QPSK	QPSK	18	18@19
8	100	75		64QAM	64QAM	20	20@55
9	100	75		QPSK	64QAM	18	20@55
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1. Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same NRB_agg. Only the combination with the highest NRB_PCC is tested. Note 3: For Low range place test point with RBstart=0. For High range place test point with RB_start=RB_end-L_CRB+1.

Table 6.6.3.3A.2_1.4.1-4: Test Configuration Table (network signalled value NS_03/NS_07)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Low and High range for both PCC and SCC (Note 3)
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg(Note 2)
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_03)	SCC (NS_07)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
1	25	50	N/A for this test	QPSK	QPSK	6	6@13
2	25	50		64QAM	64QAM	25	50
3	25	50		QPSK	64QAM	6	50
4	50	50		QPSK	QPSK	6	6@13
5	50	50		64QAM	64QAM	50	50
6	50	50		QPSK	64QAM	6	50
7	100	50		QPSK	QPSK	10	6@13
8	100	50		64QAM	64QAM	100	50
9	100	50		QPSK	64QAM	10	50
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1. Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same NRB_agg. Only the combination with the highest NRB_PCC is tested. Note 3: For Low range place test point with RBstart=0. For High range place test point with RB_start=RB_end-L_CRB+1.

Table 6.6.3.3A.2_1.4.1-5: Test Configuration Table (network signalled value NS_05/NS_01)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Low and High range for both PCC and SCC (Note 3)
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg(Note 2)
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_05)	SCC (NS_01)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
1	25	15	N/A for this test	QPSK	QPSK	6	4
2	25	15		64QAM	64QAM	25	6
3	25	15		64QAM	QPSK	25	4
4	25	25		QPSK	QPSK	6	6
5	25	25		64QAM	64QAM	25	25
6	25	25		64QAM	QPSK	25	6
7	25	50		QPSK	QPSK	6	12
8	25	50		64QAM	64QAM	25	25
9	25	50		64QAM	QPSK	25	12
10	50	50		QPSK	QPSK	12	12
11	50	50		64QAM	64QAM	50	25
12	50	50		64QAM	QPSK	50	12
13	100	50		QPSK	QPSK	18	12
14	100	50		64QAM	64QAM	50	25
15	100	50		64QAM	QPSK	50	12
16	100	75		QPSK	QPSK	18	16
17	100	75		64QAM	64QAM	50	25
18	100	75		64QAM	QPSK	50	16
19	100	100		QPSK	QPSK	18	18
20	100	100		64QAM	64QAM	50	25
21	100	100		64QAM	QPSK	50	18
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1. Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same NRB_agg. Only the combination with the highest NRB_PCC is tested. Note 3: For Low range place test point with RBstart=0. For High range place test point with RB_start=RB_end-L_CRB+1.

Table 6.6.3.3A.2_1.4.1-6: Test Configuration Table (network signalled value NS_01/NS_17)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Low and High range for both PCC and SCC (Note 3)
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg(Note 2)
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_01)	SCC (NS_17)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
1	25	25	N/A for this test	QPSK	QPSK	6	6
2	25	25		64QAM	64QAM	25	25
3	25	25		64QAM	QPSK	25	6
4	25	50		QPSK	QPSK	6	12
5	25	50		64QAM	64QAM	25	25
6	25	50		64QAM	QPSK	25	12
7	50	50		QPSK	QPSK	12	12
8	50	50		64QAM	64QAM	50	25
9	50	50		64QAM	QPSK	50	12
10	100	50		QPSK	QPSK	16	12
11	100	50		64QAM	64QAM	50	25
12	100	50		64QAM	QPSK	50	12
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1 Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same NRB_agg. Only the combination with the highest NRB_PCC is tested. Note 3: For Low range place test point with RBstart=0. For High range place test point with RB_start=RB_end-L_CRB+1.

1. Connect the SS to the UE to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure group A.33 as appropriate.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals for PCC are initially set up according to Annex C.0, C.1 and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Tables 6.6.3.3A.2_1.4.1-2 to 6.6.3.3A.2_1.4.1-6 depending on network signal value.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.3A.2_1.4.3.

6.6.3.3A.2_1.4.2 Test procedures

Same test procedure as in clause 6.6.3.3A.2.4.2 with following exceptions:

– In step 2: Instead of clause 6.6.3.3A.2.4.3  use clause 6.6.3.3A.2_1.4.3.

– In step 4: Instead of Tables 6.6.3.3A.2.4.1-2 to 6.6.3.3A.2.4.1-9  use Tables 6.6.3.3A.2_1.4.1-2 to 6.6.3.3A.2_1.4.1-6.

– In step 6: Instead of Tables 6.2.4A.2.5-1 to 6.2.4A.2.5-16  use Tables 6.2.4A.2_1.5-1 to 6.2.4A.2_1.5-11.

– In step 7: Instead of Table 6.6.3.3A.2.4.1-1  use Table 6.6.3.3A.2_1.4.1-1.

6.6.3.3A.2_1.4.3 Message contents

Same message content as in clause 6.6.3.3A.2.4.3.

6.6.3.3A.2_1.5 Test requirement

Same test requirements as in clause 6.6.3.3A.2.5.

6.6.3.3A.2_2 Additional spurious emissions for CA (inter-band DL CA and UL CA) for UL 256QAM

6.6.3.3A.2_2.1 Test purpose

6.6.3.3A.2_2.2 Test applicability

This test case applies to all types of E-UTRA UE release 14 and forward that support inter-band DL CA and UL CA and UL 256QAM.

6.6.3.3A.2_2.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.6.3.3.3.

6.6.3.3A.2_2.4 Test description

6.6.3.3A.2_2.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state. For the UE maximum output power modified by A-MPR specified in subclause 6.2.4A.2_2, the power limits specified in subclause 6.2.5A.3 apply.

Table 6.6.3.3A.2_2.4.1-1 Additional spurious emissions for inter-band CA

Uplink CA Configuration	NS-value per CC (in same order as UL CA Configuration column)		Applicable emissions requirements (in same order as UL CA Configuration column)
CA_1A-3A^{Note 3} CA_1A-5 A^{Note 3} CA_1A-7 A^{Note 3} CA_1A-8 A^{Note 3} CA_1A-18A^{Note 3} CA_1A-26A^{Note 3} CA_1A-42A^{Note 3}	NS_05	NS_01	Table 6.6.3.3.5.2-1	N/A
CA_2A-13 A^{Note 3} CA_4A-13 A^{Note 3}	NS_03	NS_07	Table 6.6.2.2.3.1-1	Table 6.6.2.2.3.3-1 Table 6.6.3.3.3.3-1
CA_3A-26 A^{Note 3}	NS_01	NS_12	N/A	Table 6.6.3.3.3.7-1
CA_3A-26 A^{Note 3}	NS_01	NS_15	N/A	Table 6.6.3.3.3.10-1
CA_1A-19A^{Note 3}	NS_05	NS_08	Table 6.6.3.3.5.2-1	Table 6.6.3.3.5.4-1
CA_1A-21A^{Note 3}	NS_05	NS_09	Table 6.6.3.3.5.2-1	Table 6.6.3.3.5.5-1
CA_1A-28A	NS_05	NS_17	Table 6.6.3.3.5.2-1	Table 6.6.3.3.5.12-1
CA_3A-19A^{Note 3}	NS_01	NS_08	N/A	Table 6.6.3.3.5.4-1
CA_19A-21A^{Note 3}	NS_08	NS_09	Table 6.6.3.3.5.4-1	Table 6.6.3.3.5.5-1
CA_18A-28A	NS_01	NS_17	N/A	Table 6.6.3.3.5.12-1
Note 1: For CCs with NS_01, there are no additional requirements defined in 36.101. Only CCs with NS-value different than NS_01 needs to be tested. Note 2: A-MPR values for NS-values in this table are the same as in section 6.2.4.3. Note 3: No test required since only A-Spur requirements apply, and the frequency range to test is unaffected by intermodulation products as described in section 4.3 in TR 36.905.

The initial test configurations consist of environmental conditions, test frequencies, and CC combinations based on E‑UTRA CA configurations specified in table 5.4.2A.1-2. All of these configurations shall be tested with applicable test parameters for each CA Configuration, and are shown in tables 6.6.3.3A.2_2.4.1-2 to 6.6.3.3A.2_2.4.1-3. The details of the uplink reference measurement channels (RMCs) are specified in Annexe A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.3A.2_2.4.1-2: Test Configuration Table (network signalled value NS_05/NS_17)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Low range, Mid range for PCC In case of Low range: For 5MHz channel bandwidth: 1927.2MHz (NUL = 18072) For 10MHz channel bandwidth: 1934.7MHz (NUL = 18147) For 20MHz channel bandwidth: 1930MHz (NUL = 18100) Mid range for SCC (Note 3)
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg(Note 2)
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_01)	SCC (NS_12)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations (L_CRB @ RB_start)
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations (L_CRB @ RB_start)
1	25	25	N/A for this test	QPSK	QPSK	6	6
2	25	25		256QAM	256QAM	25	25
3	25	25		256QAM	QPSK	25	6
4	25	50		QPSK	QPSK	6	12
5	25	50		256QAM	256QAM	25	25
6	25	50		256QAM	QPSK	25	12
7	50	50		QPSK	QPSK	12	12
8	50	50		256QAM	256QAM	50	25
9	50	50		256QAM	QPSK	50	12
10	75	50		QPSK	QPSK	16	12
11	75	50		256QAM	256QAM	50	25
12	75	50		256QAM	QPSK	50	12
13	100	50		QPSK	QPSK	18	16
14	100	50		256QAM	256QAM	50	25
15	100	50		256QAM	QPSK	50	16
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1. Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same NRB_agg. Only the combination with the highest NRB_PCC is tested. Note 3: For Low range place test point with RBstart=0. For High range place test point with RB_start=RB_max-L_CRB+1.

Table 6.6.3.3A.2_2.4.1-3: Test Configuration Table (network signalled value NS_01/NS_17)

Initial Conditions
Test Environment as specified in TS 36.508[7] subclause 4.1						NC
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes						Low and High range for both PCC and SCC (Note 3)
Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.						Lowest and Highest N_RBagg(Note 2)
Test Parameters for CA Configurations
Config ID	CA Configuration / NRB_agg		DL Allocation	CC MOD		UL Allocation
	PCC (NS_01)	SCC (NS_17)	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
	NRB	NRB	PCC & SCC RB allocation	PCC	SCC	PCC & SCC RB allocations
1	25	25	N/A for this test	QPSK	QPSK	6	6
2	25	25		256QAM	256QAM	25	25
3	25	25		256QAM	QPSK	25	6
4	25	50		QPSK	QPSK	6	12
5	25	50		256QAM	256QAM	25	25
6	25	50		256QAM	QPSK	25	12
7	50	50		QPSK	QPSK	12	12
8	50	50		256QAM	256QAM	50	25
9	50	50		256QAM	QPSK	50	12
10	75	50		QPSK	QPSK	16	12
11	75	50		256QAM	256QAM	50	25
12	75	50		256QAM	QPSK	50	12
Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-1 Note 2: If the UE supports multiple CC Combinations in the CA Configuration with the same NRB_agg. Only the combination with the highest NRB_PCC is tested. Note 3: For Low range place test point with RBstart=0. For High range place test point with RB_start=RB_max-L_CRB+1.

1. Connect the SS to the UE to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure group A.33 as appropriate.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals for PCC are initially set up according to Annex C.0, C.1 and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Tables 6.6.3.3A.2_2.4.1-2 to 6.6.3.3A.2_2.4.1-3 depending on network signal value.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.3A.2_2.4.3.

6.6.3.3A.2_2.4.2 Test procedures

Same test procedure as in clause 6.6.3.3A.2.4.2 with the following exception:

– In step 2: Instead of clause 6.6.3.3A.2.4.3  use clause 6.6.3.3A.2_2.4.3.

– In step 4: Instead of Tables 6.6.3.3A.2.4.1-2 to 6.6.3.3A.2.4.1-9  use Tables 6.6.3.3A.2_2.4.1-2 to 6.6.3.3A.2_2.4.1-3.

– In step 6: Instead of Tables 6.2.4A.2.5-1 to 6.2.4A.2.5-16  use Tables 6.2.4A.2_2.5-1 to 6.2.4A.2_2.5-11.

6.6.3.3A.2_2.4.3 Message contents

Same message content as in clause 6.6.3.3A.2.4.3.

6.6.3.3A.2_2.5 Test requirement

Same test requirements as in clause 6.6.3.3A.2.5.6.6.3.3A.3 Additional spurious emissions for CA (intra-band non-contiguous DL CA and UL CA)

Editor’s note: No test case details specified because the additional maximum power reduction and the additional spurious emissions cannot be verified for the intra-band non-contiguous UL CA case due to A-MPR is N/A and no additional requirement is needed in current non-contiguous Uplink CA configuration CA_4A-4A according to Table 6.2.4A-2 in TS 36.101.

6.6.3.3A.3

6.6.3.3A.4 Additional spurious emissions for CA (3UL CA)

Editor’s notes: This test case is incomplete. The following items are missing or incomplete:

– Test configuration table is FFS

6.6.3.3A.4.1 Test purpose

To verify that UE transmitter does not cause unacceptable interference to other channels or other systems in terms of transmitter spurious emissions in intra-band contiguous carrier aggregation and inter-band carrier aggregation under the deployment scenarios where additional requirements are specified.

6.6.3.3A.4.2 Test applicability

This test case applies to all types of E-UTRA UE release 13 and forward that support intra-band contiguous or inter-band and 3UL CA but do not support UL 64QAM or UL 256QAM.

6.6.3.3A.4.3 Minimum conformance requirements

This clause specifies the requirements for the specified E-UTRA band for an additional spectrum emission for CA requirement with protected bands as indicated in Table 6.6.3.3A.4.3.1-1.

6.6.3.3A.4.3.1 Minimum conformance requirements for CA_39C-41A (network signalled value "CA_NS_07")

When "CA_NS_07" is indicated in the cell, the power of any UE emission shall not exceed the levels specified in Table 6.6.3.3A.4.3.1-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1A.3-1 from the edge of the aggregated channel bandwidth.

Table 6.6.3.3A.4.3.1-1: Additional requirements for CA

Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	Note
Frequency range	1805	–	1855	-40	1	1
Frequency range	1855	–	1880	-15.5	5	1, 2, 3
NOTE 1: This requirement is applicable for carriers with aggregated channel bandwidths confined in 1885-1920 MHz. NOTE 2: These requirements also apply for the frequency ranges that are less than F_OOB(MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.0-1 from the edge of the aggregated channel bandwidth. NOTE 3: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band.

The normative reference for this requirement is TS 36.101[2] subclause 6.6.3.3A.6.

6.6.3.3A.4.4 Test description

6.6.3.3A.4.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and CC combinations based on E-UTRA CA configurations specified in table 5.4.2A.1-1. All of these configurations shall be tested with applicable test parameters for each CA Configuration, and are shown in table 6.6.3.3A.4.4.1-1. The details of the uplink reference measurement channels (RMCs) are specified in Annexes A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.3A.4.4.1-1: Test Configuration Table for CA (network signalled value “CA_NS_07”)

FFS

1. Connect the SS to the UE to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure group A.33 as appropriate.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals for PCC are initially set up according to Annex C.0, C.1 and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Table 6.6.3.3A.4.4.1-1 with network signal value”CA_NS_07”.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.3A.4.4.3.

6.6.3.3A.4.4.2 Test procedure

1. Configure SCC according to Annex C.0, C.1 and Annex C.3.0 for all downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4. Message contents are defined in clause 6.6.3.3A.4.4.3

3. SS activates SCC by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC on both PCC and SCC, according to Table 6.6.3.3A.4.4.1-1 with network signal value”CA_NS_07”. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

5. Send continuously uplink power control “up” commands in every uplink scheduling information to the UE until the UE transmits at P_UMAX level.

7. Measure the power of the transmitted signal with a measurement filter of bandwidths according to Table 6.6.3.3A.4.5.1-1. The centre frequency of the filter shall be stepped in contiguous steps according to the same table. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

6.6.3.3A.4.4.3 Message contents

Message contents are according to TS 36.508 [7] subclause 4.6, with the following exceptions for each network signalled value.

6.6.3.3A.4.4.3.1 Message contents (network signalled value "CA_NS_07")

Table 6.6.3.3A.4.4.3.1-1: RadioResourceConfigCommonSCell-r10-DEFAULT: Additional spectrum emission test requirement for “CA_NS_07”

Derivation Path: TS 36.508 [7] clause 4.6.3, Table 4.6.3-13A
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmissionSCell-r10	7 (CA_NS_07)

6.6.3.3A.4.5 Test requirement

This clause specifies the requirements for the specified E-UTRA band for an additional spectrum emission for CA requirement with protected bands as indicated from table 6.6.3.3A.4.5.1-1.

6.6.3.3A.4.5.1 Test requirement for CA (network signalled value “CA_NS_07")

When “CA_NS_07” is indicated in the cell:

– the measured UE mean power in the channel bandwidth, derived in step 3, shall fulfil requirements in Table 6.2.4A.1.5-7 as appropriate,

and

the measured average power of spurious emission, derived in step 2, shall not exceed the described value in Table 6.6.3.3A.4.5.1-1. This requirement also applies for the frequency ranges that are less than Δf_OOB (MHz) in Table 6.6.3.1A.1.3-1 from the edge of the channel bandwidth.

Table 6.6.3.3A.4.5.1-1: Additional requirement for CA

Protected band	Frequency range (MHz)			Maximum Level (dBm)	MBW (MHz)	NOTE
Frequency range	1805	–	1855	-40	1	1
Frequency range	1855	–	1880	-15.5	5	1, 2, 3
NOTE 1: This requirement is applicable for carriers with aggregated channel bandwidths confined in 1885-1920 MHz NOTE 2: The requirement also applies for the frequency ranges that are less than FOOB (MHz) in Table 6.6.3.1.3-1 and Table 6.6.3.1A.0-1 from the edge of the channel bandwidth. NOTE 3: For these adjacent bands, the emission limit could imply risk of harmful interference to UE(s) operating in the protected operating band.

6.6.3.3A.5 Additional spurious emissions for CA (4UL CA)

Editor’s Note: This test case is incomplete. The following items are missing or are incomplete:

Test configuration table is TBD, because A-MPR test case for 4UL CA is incomplete
A-MPR related test requirements are TBD, because A-MPR test case for 4UL CA is incomplete

6.6.3.3A.5.1 Test purpose

6.6.3.3A.5.2 Test applicability

This test case applies to all types of E-UTRA UE release 11 and forward that support inter-band and 4UL CA.

6.6.3.3A.5.3 Minimum conformance requirements

Same minimum conformance requirements as in clause 6.6.3.3A.1.3

6.6.3.3A.5.4 Test description

6.6.3.3A.5.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state. For the UE maximum output power modified by A-MPR specified in table 6.6.3.3A.5.4.1-1, the power limits specified in subclause 6.2.5A.6.3 apply.

Table 6.6.3.3A.2.4.1-1: Additional spurious emissions for inter-band CA

Uplink CA Configuration	NS-value per CC (in same order as UL CA Configuration column)		Applicable emissions requirements (in same order as UL CA Configuration column)
CA_41C-42C	CA_NS_04	CA_NS_08	Table 6.6.3.3A.1.3.8-1	Table 6.6.3.3A.1.3.7-1
Note 1: A-MPR values for NS-values in this table are the same as in section 6.2.4.3.

The initial test configurations consist of environmental conditions, test frequencies, and CC combinations based on E-UTRA CA configurations specified in table 5.4.2A.1-2. All of these configurations shall be tested with applicable test parameters for each CA Configuration, and are shown in table 6.6.3.3A.5.4.1-2. The details of the uplink reference measurement channels (RMCs) are specified in Annexes A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.6.3.3A.5.4.1-2: Test Configuration Table (network signalled value CA_NS_04/CA_NS_08)

Initial Conditions

Test Environment as specified in TS 36.508 [7] subclause 4.1

Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 for different CA bandwidth classes

Low and High range for both PCC and SCC

Test CC Combination setting (NRB_agg) as specified in subclause 5.4.2A.1 for the CA Configuration across bandwidth combination sets supported by the UE.

Lowest and Highest N_RBagg

Test Parameters for CA Configurations

Config ID

CA Configuration / NRB_agg

DL Allocation

CC MOD

UL Allocation

PCC

SCC1

SCC2

SCC3

PCC & SCC RB allocation

PCC

SCC1

SCC2

SCC3

PCC & SCC RB allocations

NRB

TBD

N/A for this test

TBD

Note 1: CA Configuration Test CC Combination settings are checked separately for each CA Configuration. which applicable aggregated channel bandwidths are specified in Table 5.4.2A.1-2.

1. Connect the SS to the UE to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure group A.56 as appropriate.

2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.

3. Downlink signals for PCC are initially set up according to Annex C.0, C.1 and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to Table 6.6.3.3A.5.4.1-2.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.6.3.3A.5.4.3.

6.6.3.3A.5.4.2 Test procedure

1. Configure SCCs according to Annex C.0, C.1 and Annex C.3.0 for all downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [7] clause 5.2A.4. Message contents are defined in clause 6.6.3.3A.5.4.3

3. SS activates SCCs by sending the activation MAC-CE (Refer TS 36.321 [13], clauses 5.13, 6.1.3.8). Wait for at least 2 seconds (Refer TS 36.133, clauses 8.3.3.2).

4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC on both PCC and SCC, according to Table 6.6.3.3A.5.4.1-2. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

5. Send continuously uplink power control “up” commands in every uplink scheduling information to the UE until the UE transmits at P_UMAX level.

6. Measure the mean power of the UE in the channel bandwidth of the radio access mode according to the test configuration, which shall meet the requirements described in Tables TBD. The period of the measurement shall be at least one sub-frame (1ms).

7. Measure the power of the transmitted signal with a measurement filter of bandwidths according to Table 6.6.3.3A.1.5.1-1 to 6.6.3.3A.1.5.8-1 as appropriate. The centre frequency of the filter shall be stepped in contiguous steps according to the same table. The measured power shall be verified for each step. The measurement period shall capture the active time slots.

6.6.3.3A.5.4.3 Message contents

Same message contents as in clause 6.2.4A.5.4.3.

6.6.3.3A.5.5 Test requirement

Same test requirements as in clause 6.6.3.3A.1.5 depending on network signal value.