6.5.1E Frequency Error for UE category 0

36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification

6.5.1E.1 Test purpose

Same test purpose as in clause 6.5.1.1.

6.5.1E.2 Test applicability

This test case applies to all types of E-UTRA UE release 12 and forward of UE category 0.

6.5.1E.3 Minimum conformance requirements

Same minimum conformance requirements as in clause 6.5.1.3.

6.5.1E.4 Test description

6.5.1E.4.1 Initial condition

Same initial conditions as in clause 6.5.1.4.1 with following exceptions:

– Instead of Table 6.5.1.4.1-1 🡪 use Table 6.5.1E.4.1-1.

– Connect SS to the UE antenna connectors as shown in TS 36.508[7] Annex A Figure A.3 using only main UE Tx/Rx antenna.

Table 6.5.1E.4.1-1: Test Configuration Table

Initial Conditions

Test Environment as specified in

TS 36.508[7] subclause 4.1

NC, TL/VL, TL/VH, TH/VL, TH/VH

Test Frequencies as specified in

TS36.508 [7] subclause 4.3.1

Low range, Mid range, High range

Test Channel Bandwidths as specified in

TS 36.508 [7] subclause 4.3.1

Lowest, 5MHz, Highest

Test Parameters for Channel Bandwidths

Downlink Configuration

Uplink Configuration

Ch BW

Mod’n

RB allocation

Mod’n

RB allocation

FDD and HD-FDD

TDD

FDD and HD-FDD

TDD

1.4MHz

QPSK

6

6

QPSK

6

6

3MHz

QPSK

14

14

QPSK

15

15

5MHz

QPSK

14

14

QPSK

25

25

5MHz

QPSK

14

N/A

QPSK

20

N/A

5MHz

QPSK

14

N/A

QPSK

15

N/A

10MHz

QPSK

14

14

QPSK

50

36

10MHz

QPSK

14

N/A

QPSK

25

N/A

10MHz

QPSK

14

N/A

QPSK

20

N/A

10MHz

QPSK

14

N/A

QPSK

15

N/A

15MHz

QPSK

14

14

QPSK

36

36

15MHz

QPSK

14

N/A

QPSK

36

N/A

15MHz

QPSK

14

N/A

QPSK

25

N/A

15MHz

QPSK

14

N/A

QPSK

20

N/A

20MHz

QPSK

14

14

QPSK

36

36

20MHz

QPSK

14

N/A

QPSK

36

N/A

20MHz

QPSK

14

N/A

QPSK

25

N/A

20MHz

QPSK

14

N/A

QPSK

20

N/A

Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, which applicable channel bandwidths are specified in Table 5.4.2.1-1.

Note 2: Depending on E-UTRA band, only the appropriate Uplink RB allocation value according to table 7.3.3-2 is tested per Test Channel Bandwidth.
6.5.1E.4.2 Test procedure

Same test procedure as in clause 6.5.1.4.2 with following exception for HD-FDD:

– In step 4, slots with transient periods are not under test. Half-duplex guard sub frame are not under test.

6.5.1E.4.3 Message contents

Message contents are according to TS 36.508 [7] subclause 4.6 with the exceptions in subclause 7.3.4.3 and Table 7.3.3-3.

6.5.1E.5 Test requirement

The 20 frequency error Δf results must fulfil the test requirement:

|Δf| ≤ (0.1 PPM + 15 Hz)