6.2.4_1 Additional Maximum Power Reduction (A-MPR) for HPUE

36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification

6.2.4_1.1 Test purpose

Same test purpose as in clause 6.2.4.1 with the follow exception:

– Instead of Table 6.2.2.3-1 🡪 use Table 6.2.2_1.3-1

6.2.4_1.2 Test applicability

The requirements of this test apply in test case 6.6.2.2 Additional Spectrum Emission Mask and 6.6.3.3 Additional spurious emissions for network signalled values NS_04, NS_06 and NS_44 to all types of E-UTRA Power Class 1 or Power Class 2 UE release 10 and forward.

NOTE: As a result TC 6.2.4_1 has not been included in the test case applicability table 4.1-1, TS 36.521-2. This does not preclude the test from being used for R&D or other purposes if deemed useful.

6.2.4_1.3 Minimum conformance requirements

For UE Power Class 1 or Power Class 2 the specific requirements and identified sub-clauses are specified in Table 6.2.4_1.3-1 along with the allowed A-MPR values that may be used to meet these requirements. The allowed A-MPR values specified in Table 6.2.4_1.3-1 are in addition to the allowed MPR requirements specified in clause 6.2.3_1. For the UE maximum output power modified by A-MPR, the power limits specified in clause 6.2.5_1 apply.

The normative reference for this requirement is TS 36.101 clause 6.2.4.

Table 6.2.4_1.3-1: Additional Maximum Power Reduction (A-MPR) / Spectrum Emission requirements

Network Signalling value

Requirements (sub-clause)

E-UTRA Band

Channel bandwidth (MHz)

Resources Blocks

(NRB)

A-MPR (dB)

NS_04

6.6.2.2.3.2, 6.6.3.3.3.1

41

5,10,15,20

Table 6.2.4_1.3-2

NS_06

6.6.2.2.3.3

12, 13, 14, 17

1.4, 3, 5, 10

Table 5.4.2-1

N/A

NS_44

6.6.3.3.33

38 (Note 1)

5, 10, 15, 20

Table 6.2.4_1.3-3

NOTE 1: Applicable for power class 2 UE in E-UTRA carrier with channel bandwidth is confined within 2570 MHz and 2615 MHz.

Table 6.2.4_1.3-2: A-MPR requirements for "NS_04" for Power Class 2 UE

Channel bandwidth [MHz]

Parameters

5

Fc [MHz]

≤ 2500.5

> 2500.5

RBstart

0 – 8

9 – 24

0 – 24

LCRB [RBs]

> 0

> 0

> 0

A-MPR [dB]

≤ 3

0

0

10

Fc [MHz]

≤ 2504

> 2504

RBstart

0 – 8

9 – 35

36 – 49

0 – 49

LCRB [RBs]

≤ 15

> 15 and < 25

≥ 25

N/A

> 0

> 0

RBstart + LCRB [RBs]

N/A

N/A

N/A

≥ 45

N/A

N/A

A-MPR [dB]

≤ 5

≤ 2

≤ 3

≤ 1

0

0

15

Fc [MHz]

≤ 2510.8

> 2510.8

RBstart

0 – 13

14 – 59

60 – 74

0 – 74

LCRB [RBs]

≤ 18

> 18 and < 36

≥ 36

N/A

> 0

> 0

RBstart + LCRB [RBs]

N/A

N/A

N/A

≥ 62

N/A

N/A

A-MPR [dB]

≤ 5

≤ 2

≤ 4

≤ 3

0

0

20

Fc [MHz]

≤ 2517.5

> 2517.5

RBstart

0 – 22

23 – 76

77 – 99

0 – 99

LCRB [RBs]

≤ 18

> 18 and < 40

≥ 40

N/A

> 0

> 0

RBstart + LCRB [RBs]

N/A

N/A

N/A

≥ 86

N/A

N/A

A-MPR [dB]

≤ 5

≤ 2

≤ 4

≤ 3

0

0

NOTE 1: RBstart indicates the lowest RB index of transmitted resource blocks

NOTE 2: LCRB is the length of a contiguous resource block allocation

NOTE 3: For intra-subframe frequency hopping which intersects regions, notes 1 and 2 apply on a per slot basis

NOTE 4: For intra-subframe frequency hopping which intersects regions, the larger A-MPR value may be applied for both slots in the subframe

For a power class 2 capable UE operating in Band 41, A-MPR according to Table 6.2.4.3-2, Table 6.2.4.3-3, or Table 6.2.4.3-4 for power class 3 is allowed when an IE P-max as defined in [5] of 23 dBm or lower is indicated in the cell or if the uplink/downlink configuration is 0 or 6.

Table 6.2.4_1.3-3: A-MPR requirements for "NS_44" for Power Class 2 UE

Channel bandwidth [MHz]

Parameters

10

Fc [MHz]

≥2605

<2605

RBstart

0 – 5

38-49

0 – 49

LCRB [RBs]

≥ 45

< 13

> 0

RBstart + LCRB [RBs]

N/A

NA

N/A

A-MPR [dB]

≤ 1

≤ 1

0

15

Fc [MHz]

≥2597.5

<2597.5

RBstart

0 – 18

19-30

54-74

0 – 74

LCRB [RBs]

N/A

≥ 45& <56

< 17

> 0

RBstart + LCRB [RBs]

≥ 63

N/A

NA

N/A

A-MPR [dB]

≤ 1

≤ 1

≤ 1

0

20

Fc [MHz]

≥2590

<2590

RBstart

0 – 31

32-55

70-99

0 – 99

LCRB [RBs]

N/A

≥ 45& <68

< 19

> 0

RBstart + LCRB [RBs]

≥ 76

N/A

NA

N/A

A-MPR [dB]

≤ 2

≤ 1

≤ 1

0

6.2.4_1.4 Test description

Same test description as in clause 6.2.4.4 with the following exceptions:

Instead of Table 6.2.4.4.1-1 to 6.2.4.4.1-26 🡪 use Table 6.2.4_1.4-1 or Table 6.2.4_1.4-2.

Table 6.2.4_1.4-1: Test Configuration Table (network signalled value "NS_04")

Initial Conditions

Test Environment

(as specified in TS 36.508 [7] subclause 4.1)

Normal

Test Frequencies

(as specified in TS 36.508 [7] subclause 4.3.1)

Low Range, Mid Range, High Range

Additional test frequencies:

For 5 MHz bandwidth:

2500.6 MHz, NUL= 39696

For 10 MHz bandwidth:

2504.1 MHz, NUL= 39731

For 15 MHz bandwidth:

2510.9 MHz, NUL= 39799

For 20 MHz bandwidth:

2517.6 MHz, NUL= 39866

Test Channel Bandwidths

(as specified in TS 36.508 [7] subclause 4.3.1)

5MHz, 10MHz, 15MHz, 20MHz

Test Parameters for NS_05 A-MPR

Downlink Configuration

Uplink Configuration

Configuration

ID

Ch BW

Mod’n

RB allocation FDD

Mod’n

RB allocation FDD

RBstart

FDD

1 (Note 1)

5MHz

N/A for A-MPR testing

QPSK

1

0

2 (Note 1)

5MHz

QPSK

16

9

3 (Note 2)

5MHz

QPSK

25

0

4 (Note 1)

5MHz

16QAM

16

9

5 (Note 2)

5MHz

16QAM

25

0

6 (Note 1)

10MHz

QPSK

1

0

7 (Note 1)

10MHz

QPSK

1

49

8 (Note 1)

10MHz

QPSK

24

0

9 (Note 1)

10MHz

QPSK

40

10

10

10MHz

QPSK

50

0

11

10MHz

16QAM

50

(Note 3)

0

12 (Note 1)

15MHz

QPSK

1

0

13 (Note 1)

15MHz

QPSK

1

74

14 (Note 1)

15MHz

QPSK

32

0

15 (Note 1)

15MHz

QPSK

60

15

16

15MHz

QPSK

75

0

17

15MHz

16QAM

75

(Note 3)

0

18 (Note 1)

20MHz

QPSK

1

0

19 (Note 1)

20MHz

QPSK

1

99

20 (Note 1)

20MHz

QPSK

36

0

21 (Note 1)

20MHz

QPSK

75

25

22

20MHz

QPSK

100

0

23

20MHz

16QAM

100

(Note 3)

0

Note 1: Only applicable for Low Range.

Note 2: Only applicable for Mid, High Range and additional test frequencies.

Note 3: Applies only for UE-Categories ≥2.

Table 6.2.4_1.4-2: Test Configuration Table (network signalled value "NS_06")

Initial Conditions

Test Environment

(as specified in TS 36.508 [7] subclause 4.1)

Normal

Test Frequencies

(as specified in TS 36.508 [7] subclause 4.3.1)

Low range, Mid range, High range

Test Channel Bandwidths

(as specified in TS 36.508 [7] subclause 4.3.1)

Lowest, 5MHz, 10MHz, Highest

Test Parameters for NS_06 A-MPR

Downlink Configuration

Uplink Configuration

Configuration

ID

Ch BW

Mod’n

RB allocation FDD

Mod’n

RB allocation FDD

1

5MHz

N/A for A-MPR testing

QPSK

25

2

5MHz

QPSK

8

3

5MHz

16QAM

8

4

10MHz

QPSK

50

5

10MHz

QPSK

12

6

10MHz

16QAM

12

Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1.

Note 2: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE.

Note 3: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth.

Table 6.2.4_1.4-3: Test Configuration Table (network signalled value "NS_44")

Initial Conditions

Test Environment

(as specified in TS 36.508 [7] subclause 4.1)

Normal

Test Frequencies

(as specified in TS 36.508 [7] subclause 4.3.1)

Low Range, Mid Range

Additional test frequencies:

For 5 MHz bandwidth:

2612.5 MHz, NUL= 38175

For 10 MHz bandwidth:

2610 MHz, NUL= 38150

For 15 MHz bandwidth:

2607.5 MHz, NUL= 38125

For 20 MHz bandwidth:

2605 MHz, NUL= 38100

Test Channel Bandwidths

(as specified in TS 36.508 [7] subclause 4.3.1)

5MHz, 10MHz, 15MHz, 20MHz

Test Parameters for NS_44 A-MPR

Downlink Configuration

Uplink Configuration

Configuration

ID

Frequency

Ch BW

Mod’n

RB allocation FDD

Mod’n

RB allocation FDD

RBstart

FDD

1

Note 1

5MHz

N/A for A-MPR testing

QPSK

1

24

2

Note 1

5MHz

QPSK

25

0

3

Note 1

5MHz

16QAM

1

24

4

Note 1

5MHz

16QAM

25

0

5

Note 1

10MHz

QPSK

1

49

6

Note 1

10MHz

QPSK

45

5

7

Low/Mid

10MHz

QPSK

50

0

8

Note 1

10MHz

16QAM

1

49

9

Note 1

10MHz

16QAM

45

5

10

Low/Mid

10MHz

16QAM

50

0

11

Note 1

15MHz

QPSK

75

0

12

Note 1

15MHz

QPSK

45

30

13

Note 1

15MHz

QPSK

1

74

14

Low/Mid

15MHz

QPSK

75

0

15

Note 1

15MHz

16QAM

75

0

16

Note 1

15MHz

16QAM

45

30

17

Note 1

15MHz

16QAM

1

74

18

Low/Mid

15MHz

16QAM

75

0

19

Mid/Note 1

20MHz

QPSK

100

0

20

Mid/Note 1

20MHz

QPSK

45

55

21

Mid/Note 1

20MHz

QPSK

1

99

22

Low

20MHz

QPSK

100

0

23

Mid/Note 1

20MHz

16QAM

100

0

24

Mid/Note 1

20MHz

16QAM

45

55

25

Mid/Note 1

20MHz

16QAM

1

99

26

Low

20MHz

16QAM

100

0

Note 1: Only applicable for additional test frequencies.

6.2.4_1.5 Test requirements

The maximum output power, derived in step 2 of clause 6.2.4_1.4.2 shall be within the range prescribed by the nominal maximum output power and tolerance in Table 6.2.4_1.5-1 and 6.2.4_1.5-2. The allowed A-MPR values specified in Table 6.2.4_1.3-1 are in addition to the allowed MPR requirements specified in clause 6.2.3_1. For the UE maximum output power modified by MPR and/or A-MPR, the power limits specified in Table 6.2.5_1.3-1 apply.

Table 6.2.4_1.5-1: HPUE Power Class 1 test requirements (network signalled value "NS_06")

Configuration ID

EUTRA band

Class 1 (dBm)

Tol. (dB)

1

14

31

+2.7 /

-4.7

2

14

31

+2.7 /

-3.7

3

14

31

+2.7 /

-4.7

4

14

31

+2.7 /

-4.7

5

14

31

+2.7 /

-3.7

6

14

31

+2.7 /

-4.7

Table 6.2.4_1.5-2: UE Power Class 2 test requirements (network signalled value "NS_04")

Configuration ID

MPR (dB)

A-MPR (dB)

ΔTC,c (dB)

PCMAX,c (dBm)

T(PCMAX_L,c) (dB)

Upper limit (dBm)

Lower limit (dBm)

1

0

3

1.5

21.5

2.0

28.7

18.8

2

1

0

0

25

2.0

28.7

22.3

3

1

0

0

25

2.0

28.7

22.3

4

2

0

0

24

2.0

28.7

21.3

5

2

0

0

24

2.0

28.7

21.3

6

0

5

1.5

19.5

3.5

28.7

15.3

7

0

0

0

26

2.0

28.7

23.3

8

1

2

0

23

2.0

28.7

20.3

9

1

1

0

24

2.0

28.7

21.3

10

(Low Range)

1

3

0

22

2.0

28.7

19.3

10

(Mid, High Range, 2504.1 MHz)

1

0

0

25

2.0

28.7

22.3

11

(Low Range)

2

3

0

24

2.0

28.7

18.3

11

(Mid, High Range, 2504.1 MHz )

2

0

0

24

2.0

28.7

21.3

12

0

5

1.5

19.5

3.5

28.7

15.3

13

0

0

0

26

2.0

28.7

23.3

14

1

2

0

23

2.0

28.7

20.3

15

1

3

0

22

2.0

28.7

19.3

16

(Low Range)

1

4

0

21

2.0

28.7

18.3

16

(Mid, High Range, 2510.9 MHz)

1

0

0

25

2.0

28.7

22.3

17

(Low Range)

2

4

0

24

2.5

28.7

16.8

17

(Mid, High Range, 2510.9 MHz)

2

0

0

25

2.0

28.7

21.3

18

0

5

1.5

19.5

3.5

28.7

15.3

19

0

0

0

26

2.0

28.7

23.3

20

1

2

0

23

2.0

28.7

20.3

21

1

3

0

22

2.0

28.7

19.3

22

(Low Range)

1

4

0

21

2.0

28.7

18.3

22

(Mid, High Range, 2517.6 MHz)

1

0

0

25

2.0

28.7

22.3

23

(Low Range)

2

4

0

20

2.5

28.7

16.8

23

(Mid, High Range, 2517.6 MHz)

2

0

0

24

2.0

28.7

21.3

Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4_1.5-3: UE Power Class 2 test requirements (network signalled value "NS_44")

Configuration ID

MPR (dB)

A-MPR (dB)

ΔTC,c (dB)

PCMAX,c (dBm)

T(PCMAX_L,c) (dB)

Upper limit (dBm)

Lower limit (dBm)

1

0

0

0

26

2.0

28.7

23.3

2

1

0

0

25

2.0

28.7

22.3

3

1

0

0

25

2.0

28.7

22.3

4

2

0

0

24

2.0

28.7

21.3

5

0

1

0

25

2.0

28.7

22.3

6

1

1

0

24

2.0

28.7

21.3

7

1

0

0

25

2.0

28.7

22.3

8

1

1

0

24

2.0

28.7

21.3

9

2

1

0

23

2.0

28.7

20.3

10

2

0

0

24

2.0

28.7

21.3

11

1

1

0

24

2.0

28.7

21.3

12

2

1

0

23

2.0

28.7

20.3

13

0

1

0

25

2.0

28.7

22.3

14

1

0

0

25

2.0

28.7

22.3

15

2

1

0

23

2.0

28.7

20.3

16

2

1

0

23

2.0

28.7

20.3

17

1

1

0

24

2.0

28.7

21.3

18

2

0

0

24

2.0

28.7

21.3

19

1

2

0

23

2.0

28.7

20.3

20

1

1

0

24

2.0

28.7

21.3

21

0

1

0

25

2.0

28.7

22.3

22

1

0

0

25

2.0

28.7

22.3

23

2

2

0

22

2.0

28.7

19.3

24

2

1

0

23

2.0

28.7

20.3

25

1

1

0

24

2.0

28.7

21.3

26

2

0

0

24

2.0

28.7

21.3

Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1.