6.2.4 Additional Maximum Power Reduction (A-MPR)

36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification

Tools: ARFCN - Frequency Conversion for 5G NR/LTE/UMTS/GSM

Editor’s note: The following aspects are either missing or not yet determined:

– TT and test points are TBD.

6.2.4.1 Test purpose

Additional ACLR and spectrum emission requirements can be signalled by the network to indicate that the UE shall also meet additional requirements in a specific deployment scenario. To meet these additional requirements, Additional Maximum Power Reduction A-MPR is allowed for the output power as specified in Table 6.2.2.3-1. Unless stated otherwise, an A-MPR of 0 dB shall be used.

6.2.4.2 Test applicability

The requirements of this test apply in test case 6.6.2.2 Additional Spectrum Emission Mask for network signalled values NS_03, NS_04, NS_06, NS_07, NS_11, NS_20, NS_21, NS_27 and NS_35 to all types of E-UTRA Power Class 3 UE release 8 and forward.

The requirements of this test apply in test case 6.6.3.3 Additional Spurious Emissions for network signalled values NS_05, NS_07, NS_08, NS_09, NS_11, NS_12, NS_13, NS_14, NS_15, NS_16, NS_17, NS_18, NS_19, NS_20, NS_21, NS_22, NS_23, NS_24, NS_25, NS_27, NS_28, NS_29, NS_30, NS 31, NS_36, NS_38, NS_39, NS_45, NS_56 to all types of E-UTRA Power Class 3 UE release 8 and forward.

NOTE: As a result TC 6.2.4 has not been included in the test case applicability table 4.1-1, TS 36.521-2. This does not preclude the test from being used for R&D or other purposes if deemed useful.

6.2.4.3 Minimum conformance requirements

For UE Power Class 3 the specific requirements and identified sub-clauses are specified in Table 6.2.4.3-1 along with the allowed A-MPR values that may be used to meet these requirements. The allowed A-MPR values specified below in Table 6.2.4.3-1 to 6.2.4.3-31 are in addition to the allowed MPR requirements specified in clause 6.2.3. For the UE maximum output power modified by A-MPR, the power limits specified in clause 6.2.5 apply.

Table 6.2.4.3-1: Additional Maximum Power Reduction (A-MPR) / Spectrum Emission requirements

Network Signalling value	Requirements (sub-clause)	E-UTRA Band	Channel bandwidth (MHz)	Resources Blocks (N_RB)	A-MPR (dB)
NS_01	6.6.2.1.1	Table 5.2-1	1.4,3,5,10,15,20	Table 5.4.2-1	N/A
NS_03	6.6.2.2.3.1	2,4,10, 23, 25,35,36, 66, 70	3	>5	≤ 1
			5	>6	≤ 1
			10	>6	≤ 1
			15	>8	≤ 1
			20	>10	≤ 1
NS_04	6.6.2.2.3.2	41	5	>6	≤1
NS_04	6.6.2.2.3.2	41	10, 15, 20	Table 6.2.4.3-2
NS_04	6.6.2.2.3.2, 6.6.3.3.3.1	41	5,10, 15, 20	Table 6.2.4.3-3, Table 6.2.4.3-4
NS_05	6.6.3.3.3.2	1	10,15,20	≥ 50 ¹	≤ 1 ¹
		1	15, 20	Table 6.2.4.3-5 ²
		65 ³	10,15,20	≥ 50	≤ 1 ¹
		65 ³	15,20	Table 6.2.4.3-5 ²
NS_06	6.6.2.2.3.3	12, 13, 14, 17	1.4, 3, 5, 10	Table 5.4.2-1	N/A
NS_06	6.6.2.2.3.3	85	5,10	Table 5.4.2-1	N/A
NS_07	6.6.2.2.3.3 6.6.3.3.3.3	13	10	Table 6.2.4.3-6	Table 6.2.4.3-6
NS_08	6.6.3.3.3.4	19	10, 15	> 44	≤ 3
NS_09	6.6.3.3.3.5	21	10, 15	> 40	≤ 1
		21	10, 15	> 55	≤ 2
		74 ⁶	10, 15	> 40	≤ 1
		74 ⁶	10, 15	> 55	≤ 2
NS_10		20	15, 20	Table 6.2.4.3-7	Table 6.2.4.3-7
NS_11	6.6.2.2.1 6.6.3.3.3.6	23¹	1.4, 3, 5, 10,15,20	Table 6.2.4.3-8	Table 6.2.4.3-8
NS_12	6.6.3.3.3.7	26	1.4, 3, 5, 10, 15	Table 6.2.4.3-9, Table 6.2.4.3-10	Table 6.2.4.3-9, Table 6.2.4.3-10
NS_13	6.6.3.3.3.8	26	5	Table 6.2.4.3-11	Table 6.2.4.3-11
NS_14	6.6.3.3.3.9	26	10, 15	Table 6.2.4.3-12	Table 6.2.4.3-12
NS_15	6.6.3.3.3.10	26	1.4, 3, 5, 10, 15	Table 6.2.4.3-13 Table 6.2.4.3-14	Table 6.2.4.3-13, Table 6.2.4.3-14
NS_16	6.6.3.3.3.11	27	3, 5, 10	Table 6.2.4.3-15, Table 6.2.4.3-16, Table 6.2.4.3-17
NS_17	6.6.3.3.3.12	28	5, 10	Table 5.4.2-1	N/A
NS_18	6.6.3.3.3.13	28	5	≥ 2	≤ 1
NS_18	6.6.3.3.3.13	28	10, 15, 20	≥ 1	≤ 4
NS_19	6.6.3.3.3.14	44	10, 15, 20	Table 6.2.4.3-18	Table 6.2.4.3-18
NS_20	6.2.2 6.6.2.2.1 6.6.3.3.3.15	23	5, 10, 15, 20	Table 6.2.4.3-19	Table 6.2.4.3-19
NS_21	6.6.2.2.3.1 6.6.3.3.3.16	30	5, 10	Table 6.2.4.3-20	Table 6.2.4.3-20
NS_22	6.6.3.3.3.17	42, 43	5, 10, 15, 20	Table 6.2.4.3-21
NS_23	6.6.3.3.3.18	42, 43	5, 10, 15, 20	N/A
NS_24	6.6.3.3.3.19	65 ⁴	5, 10, 15, 20	Table 6.2.4.3-22
NS_25	6.6.3.3.3.20	65 ⁴	5, 10, 15, 20	Table 6.2.4.3-23
…
NS_27	6.6.2.2.3.4, 6.6.3.3.3.21	48	5, 10, 15, 20	Table 6.2.4.3-24
NS_28	6.2.2A, 6.6.3.3.22	46 (NOTE 5)	20	Table 6.2.4-25	NS_28
NS_29	6.2.2A, 6.6.2.3.1a, 6.6.3.3.23	46 (NOTE 5)	20	Table 6.2.4-26	NS_29
NS_30	6.2.2A, 6.6.3.3.24	46 (NOTE 5)	20	Table 6.2.4-27	NS_30
NS_31	6.2.2A, 6.6.3.3.25	46 (NOTE 5)	20	Table 6.2.4-28	NS_31
NS_32	–	–	–	–	–
NS_35	6.6.2.2.3.5	71	5, 10, 15, 20	N/A
NS_36		68	5, 10, 15	Table 6.2.4.3-29
…
NS_38	6.6.3.3.3.27	74	3, 5, 10, 15, 20	Table 6.2.4.3-30
NS_39	6.6.3.3.3.28	74	10, 15, 20	Table 6.2.4.3-31
…
NS_45	6.6.3.3.3.29	53	1.4, 3, 5, 10	N/A
..
NS_56	6.6.3.3.3.31	24	5, 10	Table 6.2.4.3-32
Note 1 Applicable when the lower edge of the assigned E-UTRA UL channel bandwidth frequency is larger than or equal to the upper edge of PHS band (1915.7 MHz) + 4 MHz + the channel BW assigned, where channel BW is as defined in subclause 5.6. A-MPR for operations below this frequency is not covered in this version of specifications except for the channel assignments in Note2 as the emissions requirement in 6.6.3.3.3.2 may not be met. For 10MHz channel bandwidth whose carrier frequency is larger than or equal to 1945 MHz or 15 MHz channel bandwidth whose carrier frequency is larger than or equal to 1947.5 MHz, no A-MPR applies. Note 2 Applicable when carrier frequency is 1932.5 MHz for 15MHz channel bandwidth or 1930 MHz for 20MHz channel bandwidth case. Note 3: Applicable when the E-UTRA carrier is within 1920-1980 MHz. Note 4: Applicable when the upper edge of the channel bandwidth frequency is greater than 1980MHz. Note 5: Applicable only for an LAA Scell configured in Band 46.

Table 6.2.4.3-2: A-MPR for NS_04 for bandwidths > 5MHz (Rel-11 and earlier)

Channel bandwidth [MHz]	Parameters	Region A	Region B		Region C
10	RB_start ¹	0 – 12	13 – 36		37 – 49
	RB_start ¹+ L_CRB² [RBs]	N/A (Note 3)	14 – 37	>37	N/A (Note 3)
	A-MPR [dB]	≤3dB	0	≤2dB	≤3dB
15	RB_start ¹	0 – 18	19 – 55		56 – 74
	RB_start ¹+ L_CRB² [RBs]	N/A (Note 3)	20 – 56	>56	N/A (Note 3)
	A-MPR [dB]	≤3dB	0	≤2dB	≤3dB
20	RB_start ¹	0 – 24	25 – 74		75 – 99
	RB_start ¹+ L_CRB² [RBs]	N/A (Note 3)	26 – 75	>75	N/A (Note 3)
	A-MPR [dB]	≤3dB	0	≤2dB	≤3dB
Note 1: RB_start indicates the lowest RB index of transmitted resource blocks. Note 2: L_CRB is the length of a contiguous resource block allocation. Note 3: Any RB allocation that starts in Region A or C is allowed the specified A-MPR. Note 4: For intra-subframe frequency hopping which intersects regions, notes 1 and 2 apply on a per slot basis. Note 5: For intra-subframe frequency hopping which intersects regions, the larger A-MPR value may be applied for both slots in the subframe.

Table 6.2.4-3: A-MPR requirements for "NS_04" with bandwidth >5MHz (Rel-12 to Rel-13 and bit 2 of modifiedMPRbehavior = 0)

Channel bandwidth [MHz]	Parameters
5	Fc [MHz]	≤ 2499.5						> 2499.5
	RB_start	0 – 8				9 – 24		0 – 24
	L_CRB [RBs]	> 0				> 0		> 0
	A-MPR [dB]	≤ 2				0		0
10	Fc [MHz]	≤ 2504						> 2504
	RB_start	0 – 8				9 – 35	36 – 49	0 – 49
	L_CRB[RBs]	≤ 15	> 15 and < 25		≥ 25	N/A	> 0	> 0
	RB_start+ L_CRB [RBs]	N/A	N/A		N/A	≥ 45	N/A	N/A
	A-MPR [dB]	≤ 3	≤ 1		≤ 2	≤ 1	0	0
15	Fc [MHz]	≤ 2510.8						> 2510.8
	RB_start	0 – 13				14 – 59	60 – 74	0 – 74
	L_CRB[RBs]	≤ 18 or ≥ 36		> 18 and < 36		N/A	> 0	> 0
	RB_start+ L_CRB [RBs]	N/A		N/A		≥ 62	N/A	N/A
	A-MPR [dB]	≤ 3		≤ 1		≤ 1	0	0
20	Fc [MHz]	≤ 2517.5						> 2517.5
	RB_start	0 – 22				23 – 76	77 – 99	0 – 99
	L_CRB[RBs]	≤ 18 or ≥ 40		> 18 and < 40		N/A	> 0	> 0
	RB_start+ L_CRB [RBs]	N/A		N/A		≥ 86	N/A	N/A
	A-MPR [dB]	≤ 3		≤ 1		≤ 1	0	0
NOTE 1: RB_start indicates the lowest RB index of transmitted resource blocks NOTE 2: L_CRB is the length of a contiguous resource block allocation NOTE 3: For intra-subframe frequency hopping which intersects regions, notes 1 and 2 apply on a per slot basis NOTE 4: For intra-subframe frequency hopping which intersects regions, the larger A-MPR value may be applied for both slots in the subframe

Table 6.2.4.3-4: A-MPR requirements for "NS_04" for Power Class 3 UE (Rel-12 and later and bit 2 of modifiedMPRbehavior = 1)

Channel bandwidth [MHz]	Parameters
5	Fc [MHz]	≤ 2500.5						> 2500.5
	RB_start	0 – 8				9 – 24		0 – 24
	L_CRB [RBs]	> 0				> 0		> 0
	A-MPR [dB]	≤ 2				0		0
10	Fc [MHz]	≤ 2504						> 2504
	RB_start	0 – 8				9 – 35	36 – 49	0 – 49
	L_CRB[RBs]	≤ 15	> 15 and < 25		≥ 25	N/A	> 0	> 0
	RB_start+ L_CRB [RBs]	N/A	N/A		N/A	≥ 45	N/A	N/A
	A-MPR [dB]	≤ 3	≤ 1		≤ 2	≤ 1	0	0
15	Fc [MHz]	≤ 2510.8						> 2510.8
	RB_start	0 – 13				14 – 59	60 – 74	0 – 74
	L_CRB[RBs]	≤ 18 or ≥ 36		> 18 and < 36		N/A	> 0	> 0
	RB_start+ L_CRB [RBs]	N/A		N/A		≥ 62	N/A	N/A
	A-MPR [dB]	≤ 3		≤ 1		≤ 1	0	0
20	Fc [MHz]	≤ 2517.5						> 2517.5
	RB_start	0 – 22				23 – 76	77 – 99	0 – 99
	L_CRB[RBs]	≤ 18 or ≥ 40		> 18 and < 40		N/A	> 0	> 0
	RB_start+ L_CRB [RBs]	N/A		N/A		≥ 86	N/A	N/A
	A-MPR [dB]	≤ 3		≤ 1		≤ 1	0	0
NOTE 1: RB_start indicates the lowest RB index of transmitted resource blocks NOTE 2: L_CRB is the length of a contiguous resource block allocation NOTE 3: For intra-subframe frequency hopping which intersects regions, notes 1 and 2 apply on a per slot basis NOTE 4: For intra-subframe frequency hopping which intersects regions, the larger A-MPR value may be applied for both slots in the subframe

Table 6.2.4.3-5: A-MPR for "NS_05"

Channel Bandwidth [MHz]

Parameters

Fc [MHz]

1932.5

RB_start

0-7

8 – 66

67-74

L_CRB [RBs]

≥1

≤30

31 – 54

>54

≤6

A-MPR [dB]

≤11

≤3

≤5

≤1

Fc [MHz]

1930

RB_start

0-23

24-75

76-99

L_CRB [RBs]

≥1

≤24

25 – 40

41 – 50

> 50

≤6

A-MPR [dB]

≤11

≤3

≤5

≤10

≤5

≤1

Table 6.2.4.3-6: A-MPR for "NS_07"

Parameters	Region A		Region B				Region C
RB_start ¹	0 – 12		13 –18		19 – 42		43 – 49
L_CRB² [RBs]	6 – 8	1 to 5 and 9-50	<8	≥8	<18	≥18	≤2	>2
A-MPR [dB]	≤8	≤12	0	≤12	0	≤6	≤3	0
Note 1: RB_start indicates the lowest RB index of transmitted resource blocks Note 2: L_CRB is the length of a contiguous resource block allocation Note 3: For intra-subframe frequency hopping between two regions, notes 1 and 2 apply on a per slot basis. Note 4: For intra-subframe frequency hopping between two regions, the larger A-MPR value of the two regions may be applied for both slots in the subframe.

Table 6.2.4.3-7: A-MPR for "NS_10"

Channel bandwidth [MHz]	Parameters	Region A
15	RB_start ¹	0 – 10
	L_CRB [RBs]	1 -20
	A-MPR [dB]	≤ 2
20	RB_start ¹	0 – 15
	L_CRB [RBs]	1 -20
	A-MPR [dB]	≤ 5
Note 1: RB_start indicates the lowest RB index of transmitted resource blocks. Note 2: L_CRB is the length of a contiguous resource block allocation. Note 3: For intra-subframe frequency hopping which intersects Region A, notes 1 and 2 apply on a per slot basis. Note 4: For intra-subframe frequency hopping which intersect Region A, the larger A-MPR value may be applied for both slots in the subframe.

Table 6.2.4.3-8: A-MPR for NS_11

Channel Bandwidth [MHz]

Parameters

Fc [MHz]

<2004

≥2004

L_CRB [RBs]

1-15

A-MPR [dB]

≤5

≤ 1

Fc [MHz]

<2004

2004 ≤ Fc <2007

≥2007

L_CRB [RBs]

1-25

1-6 & 15-25

8-12

A-MPR [dB]

≤7

≤ 4

≤ 1

Fc [MHz]

2005 ≤ Fc <2015

2015

RB_start

0-49

L_CRB [RBs]

1-50

A-MPR [dB]

≤ 12

Fc [MHz]

<2012.5

RB_start

0-4

5-21

22-56

57-74

L_CRB [RBs]

≥1

7-50

0-6 & ≥50

≤25

>25

A-MPR [dB]

≤15

≤7

≤10

≤6

≤15

Fc [MHz]

2012.5

RB_start

0-12

13-39

40-65

66-74

L_CRB [RBs]

≥1

≥30

<30

≥ (69 – RB_start)

≥1

A-MPR [dB]

≤10

≤6

≤2

≤6.5

Fc [MHz]

2010

RB_start

0-12

13-29

30-68

69-99

L_CRB [RBs]

≥1

10-60

1-9 & >60

1-24

≥25

≥1

A-MPR [dB]

≤15

≤7

≤10

≤7

≤15

Table 6.2.4.3-9: A-MPR for "NS_12" (Rel-11 and earlier)

Channel bandwidth [MHz]	Parameters	Region A		Region B
1.4	RB_start	0		1-2
	L_CRB [RBs]	≤3	≥4	≥4
	A-MPR [dB]	≤3	≤6	≤3
3	RB_start	0-3		4-5
	L_CRB [RBs]	4-9	1-3 and 10-15	≥9
	A-MPR [dB]	≤4	≤3	≤3
5	RB_start	0-6		7-9
	L_CRB [RBs]	≤8	≥9	≥15
	A-MPR [dB]	≤5	≤3	≤3

Table 6.2.4.3-10: A-MPR for "NS_12" (Rel-12 and later)

Channel bandwidth [MHz]	Parameters	Region A		Region B
1.4	RB_start	0		1-2
	L_CRB [RBs]	≤3	≥4	≥4
	A-MPR [dB]	≤3	≤6	≤3
3	RB_start	0-3		4-5
	L_CRB [RBs]	1-15		≥9
	A-MPR [dB]	≤4		≤3
5	RB_start	0-6		0-9
	L_CRB [RBs]	≤8		≥9
	A-MPR [dB]	≤5		≤3
10	RB_start	0-15		0-22
	L_CRB [RBs]	≤18		≥20
	A-MPR [dB]	≤4		≤2
15	RB_start	0-30		0-30
	L_CRB [RBs]	≤30		≥32
	A-MPR [dB]	≤4		≤3

Table 6.2.4.3-11: A-MPR for "NS_13"

Channel bandwidth [MHz]	Parameters	Region A
5	RB_start	0-2
	L_CRB [RBs]	≤5	≥18
	A-MPR [dB]	≤3	≤2

Table 6.2.4.3-12: A-MPR for "NS_14"

Channel bandwidth [MHz]	Parameters	Region A
10	RB_start	0
	L_CRB [RBs]	≤5	≥50
	A-MPR [dB]	≤3	≤1
15	RB_start	≤8
	L_CRB [RBs]	≤16	≥50
	A-MPR [dB]	≤3	≤1

Table 6.2.4.3-13: A-MPR for "NS_15" for E-UTRA highest channel edge ≤ 845 MHz

Channel bandwidth [MHz]	Parameters	Region A	Region B	Region C
5	RB_end [RB]			19-24
	L_CRB [RB]			≥18
	A-MPR [dB]			≤2
10	RB_end [RB]	0-4	29-44	45-49
	L_CRB [RB]	≤2	≥24	>0
	A-MPR [dB]	≤4	≤4	≤9
15	RB_end [RB]	0-12	44-61	62-74
	L_CRB [RB]	≤2	≥20	>0
	A-MPR [dB]	≤4	≤5	≤9

Table 6.2.4.3-14: A-MPR for "NS_15" for E-UTRA highest channel edge > 845 MHz and ≤ 849 MHz

Channel bandwidth

[MHz]

Parameters

Region A

Region B

Region C

1.4

RB_end [RB]

4-5

A-MPR [dB]

≤3

RB_end [RB]

0-1

8-12

13-14

L_CRB [RB]

≤2

≥8

A-MPR [dB]

≤4

≤9

RB_end [RB]

0-4

12-19

20-24

L_CRB [RB]

≤2

≥8

A-MPR [dB]

≤4

≤5

≤9

RB_end [RB]

0-12

23-36

37-49

L_CRB [RB]

≤2

≥15

A-MPR [dB]

≤4

≤6

≤9

RB_end [RB]

0-20

26-53

54-74

L_CRB [RB]

≤2

≥20

A-MPR [dB]

≤4

≤5

≤9

Table 6.2.4.3-15: A-MPR for “NS_16” with channel lower edge at ≥807 MHz and <808.5 MHz

Channel band-width [MHz]	Parameter	Region A	Region B	Region C	Region D	Region E
3 MHz	RB_start	0	1-2
	L_CRB [RBs]	≥12	12
	A-MPR [dB]	≤2	≤1
5 MHz	RB_start	0-1	2	2-9	2-5
	L_CRB [RBs]	1 – 25	12	15-18	20
	A-MPR [dB]	≤5	≤1	≤2	≤3
10 MHz	RB_start	0 – 8	0-14		15-20	15-24
	L_CRB [RBs]	1 – 12	15-20	≥24	≥30	24-27
	A-MPR [dB]	≤5	≤3	≤7	≤3	≤1

Table 6.2.4.3-16: A-MPR for “NS_16” with channel lower edge at ≥808.5 MHz and <812 MHz

Channel band-width [MHz]	Parameter	Region A	Region B	Region C	Region D	Region E
5 MHz	RB_start	0	0-1	1-5
	L_CRB [RBs]	16-20	≥24	16-20
	A-MPR [dB]	≤2	≤3	≤1
10 MHz	RB_start	0-6		0-10	0-14	11-20
	L_CRB [RBs]	1-12	15-20	24-32	≥36	24-32
	A-MPR [dB]	≤5	≤2	≤4	≤5	≤1

Table 6.2.4.3-17: A-MPR for “NS_16” with channel lower edge at ≥812 MHz

Channel band-width [MHz]	Parameter	Region A	Region B	Region C	Region D
10 MHz	RB_start	0 – 9	0	1-14	0-5
	L_CRB [RBs]	27-32	36-40	36-40	≥45
	A-MPR [dB]	≤1	≤2	≤1	≤3

Table 6.2.4.3-18: A-MPR for “NS_19”

Channel bandwidth [MHz]	Parameters	Region A		Region B
10	RB_start			0-6
	L_CRB [RBs]			≥40
	A-MPR [dB]			≤1
15	RB_start	0-6		7-20
	L_CRB [RBs]	≤18	≥36	≥42
	A-MPR [dB]	≤2	≤3	≤2
20	RB_start	0-14		15-30
	L_CRB [RBs]	≤40	≥45	≥50
	A-MPR [dB]	≤2	≤3	≤2

Table 6.2.4.3-19: A-MPR for “NS_20”

Channel bandwidth [MHz]

Parameters

Fc (MHz)

< 2007.5

2007.5 ≤ Fc < 2012.5

2012.5 ≤ Fc ≤ 2017.5

RB_start

≤24

0-3

4-6

≤24

L_CRB (RBs)

15-19

≥20

≥18

1-25

A-MPR [dB]

≤17

≤1

≤4

≤2

≤ 0

Fc (MHz)

2005

RB_start

0-25

26-34

35-49

L_CRB (RBs)

8-15

>15

A-MPR [dB]

≤16

≤2

≤5

≤ 6

Fc (MHz)

2015

RB_start

0-5

6-10

L_CRB (RBs)

≥32

≥40

A-MPR [dB]

≤4

≤2

Fc (MHz)

2012.5

RB_start

0-14

15-24

25-39

61-74

L_CRB (RBs)

1-9 & 40-75

10-39

24-29

≥30

≥36

≤6

A-MPR [dB]

≤11

≤6

≤1

≤7

≤5

≤6

Fc (MHz)

2010

RB_start

0-21

22-31

32-38

39-49

50-69

70-99

L_CRB (RBs)

1-9 & 31-75

10-30

≥15

≥24

≥25

A-MPR [dB]

≤17

≤12

≤6

≤9

≤7

≤5

≤16

NOTE 1: When NS_20 is signalled the minimum requirements for the 10 MHz bandwidth are specified for E‑UTRA UL carrier centre frequencies of 2005 MHz or 2015 MHz.

NOTE 2: When NS_20 is signalled the minimum requirements for the 15 MHz channel bandwidth are specified for E‑UTRA UL carrier centre frequency of 2012.5 MHz.

Table 6.2.4.3-20: A-MPR for "NS_21"

Channel Bandwidth [MHz]	Parameters	Region A		Region B
10	RB_start	0 – 6	0 – 6	N/A	N/A
	RB_end	N/A	N/A	43 – 49	43 – 49
	L_CRB [RBs]	1 – 2	3 – 12, 32 – 50	1 – 2	3 – 12, 32 – 50
	A-MPR [dB]	≤ 4	≤ 3	≤ 4	≤ 3

Table 6.2.4.3-21: A-MPR for "NS_22"

Channel bandwidth [MHz]	Parameters	Region A	Region B	Region C	Region D
5	No A-MPR is needed for 5 MHz channel bandwidth
10	RB_start	0-13	0-17	≤ 6	≥12
	L_CRB [RBs]	> 36	33-36	≤ 32	≤ 32
	RBstart + LCRB [RBs]	N/A	N/A	N/A	≥44
	A-MPR [dB]	≤ 4	≤ 3	≤ 3	≤ 3
15	RB_start	0-24	0-38	≤ 14	≥ 23
	L_CRB [RBs]	> 50	37-50	≤ 36	≤ 36
	RBstart + LCRB [RBs]	N/A	N/A	N/A	≥59
	A-MPR [dB]	≤ 5	≤ 4	≤ 3	≤ 3
20	RB_start	0-35	0-51	≤ 21	≥ 31
	L_CRB [RBs]	> 64	49-64	≤ 48	≤ 48
	RBstart + LCRB [RBs]	N/A	N/A	N/A	≥79
	A-MPR [dB]	≤ 5	≤ 4	≤ 3	≤ 3
NOTE 1: RB_start indicates the lowest RB index of transmitted resource blocks NOTE 2: L_CRB is the length of a contiguous resource block allocation NOTE 3: For intra-subframe frequency hopping between two regions, notes 1 and 2 apply on a per slot basis. NOTE 4: For intra-subframe frequency hopping between two regions, the larger A-MPR value of the two regions may be applied for both slots in the subframe.

Table 6.2.4.3-22: A-MPR for "NS_24"

Channel Bandwidth [MHz]	Parameters
5	Fc [MHz]	Fc > [1987.5]
	RB_start	0 – 24
	L_CRB [RBs]	0 – 24
	A-MPR [dB]	≤ 10
10	Fc [MHz]	1975 < Fc ≤ 1985							1985<Fc≤1995		Fc>1995
	RB_start	0 – 1	2 – 14		15 – 26	36 – 49			0 – 49		0 – 49
	L_CRB [RBs]	> 10	≥ 35		N/A	≤ 2		> 11	0 – 49		0 – 49
	RB_end	N/A	N/A		> 48	N/A		N/A	N/A		N/A
	A-MPR [dB]	≤ 2	≤ 2		1	≤ 3		≤ 1	≤ 9		≤ 17
15	Fc [MHz]	1972.5 < Fc ≤ 1987.5								Fc > 1987.5
	RB_start	0 – 11					12 – 74			0 – 74
	L_CRB [RBs]	≤ 45		> 45			> 3			0 – 74
	RB_end	N/A		N/A			≥ 45			N/A
	A-MPR [dB]	≤ 2		≤ 8			≤ 7			≤ 17
20	Fc [MHz]	Fc > 1970
	RB_start	0 – 99
	L_CRB [RBs]	0 – 99
	A-MPR [dB]	≤ 17

Table 6.2.4.3-23: A-MPR for "NS_25"

Channel Bandwidth [MHz]

Parameters

Fc [MHz]

Fc > [1997.5]

RB_start

0 – 9

10 – 24

L_CRB [RBs]

> 12

N/A

RB_end

N/A

≥ 22

A-MPR [dB]

≤ 5

≤ 2

Fc [MHz]

1975 < Fc ≤ 1985

1985 < Fc ≤ 1995

Fc > 1995

RB_start

0-1

2-49

1 – 18

19-49

0-6

7-15

16-49

L_CRB [RBs]

> 10

N/A

≤ 25

> 25

N/A

> 20

N/A

RB_end

N/A

> 48

N/A

> 42

N/A

> 35

A-MPR [dB]

≤ 1

≤ 5

≤ 1

≤ 10

≤ 7

≤ 11

Fc [MHz]

1972.5 < Fc ≤ 1987.5

Fc > 1987.5

RB_start

0 – 4

5 – 30

31 – 62

63 – 74

0 – 74

L_CRB [RBs]

≥ 15

≥ 45

N/A

0 – 74

RB_end

N/A

> 71

N/A

A-MPR [dB]

≤ 4

≤ 3

≤ 1

≤ 13

Fc [MHz]

1970 < Fc ≤ 1990

Fc > 1990

RB_start

0 – 13

14 – 40

41 – 99

0 – 99

L_CRB [RBs]

N/A

≥ 32

N/A

0 – 99

RB_end

N/A

> 72

N/A

A-MPR [dB]

≤ 11

≤13

≤ 13

Table 6.2.4.3-24: A-MPR for "NS_27“

Parameters
Channel bandwidth [MHz]	RB_start	RB_end	L_CRB	A-MPR
15	0 – 6		≤ 15	≤ 4 dB
		68 – 74	≤ 15	≤ 4 dB
	≥ 0		≥ 60	≤ 2 dB
20	0 – 12		≤ 20	≤ 4 dB
		87 – 99	≤ 20	≤ 4 dB
	13 – 15		≤ 3	≤ 1 dB
		84 – 86	≤ 3	≤ 1 dB
	≥ 0		≥ 60	≤ 3 dB

Table 6.2.4-25: A-MPR for "NS_28"

Parameters
Channel Bandwidth [MHz]	Carrier centre frequency (F_C) [MHz]	Uplink resource allocation	A-MPR [dB]
20	5160¹, 5340², 5480¹	L = 10 (RIV = 19)	9
	5160¹, 5340², 5480¹	Any other RIV	8
	5700³	L = 10 (RIV = 19)	[9]
	5700³	Any other RIV	[8]
	5180³, 5200³, 5220³, 5240³, 5260³, 5280³, 5300³, 5320³, 5500³, 5520³, 5540³, 5560³, 5580³, 5600³, 5620³, 5640³, 5660³, 5680³	L = 10 (RIV = 19)	2
		Any other RIV	2
NOTE 1: Applies also for carrier centre frequencies at a frequency offset of +100 kHz or +200 kHz from the carrier centre frequency stated. NOTE 2: Applies also for carrier centre frequencies at a frequency offset of-200 kHz or -100 kHz from the carrier centre frequency stated. NOTE 3: Applies also for carrier centre frequencies at a frequency offset of -200 kHz, -100 kHz, 100 kHz or +200 kHz from the carrier centre frequency stated. NOTE 4: The carrier centre frequencies and corresponding EARFCN allowed for operation in Band 46 are specified in [12]. The uplink resource allocation is defined in Clause 8.1.4 of [10].

Table 6.2.4-26: A-MPR for "NS_29"

Parameters
Channel Bandwidth [MHz]	Carrier centre frequency (F_C) [MHz]	Uplink resource allocation	A-MPR [dB]
20	5180¹, 5200¹, 5220¹, 5240¹, 5260¹, 5280¹, 5300¹, 5320¹, 5500¹, 5520¹, 5540¹, 5560¹, 5580¹, 5600¹, 5620¹, 5640¹, 5660¹, 5680¹, 5700¹	L = 10 (RIV = 19)	2
		Any other RIV	1
NOTE 1: Applies also for carrier centre frequencies at a frequency offset of -200 kHz, -100 kHz, 100 kHz or +200 kHz from the carrier centre frequency stated NOTE 2: The carrier centre frequencies and corresponding EARFCN allowed for operation in Band 46 are specified in [12]. The uplink resource allocation is defined in Clause 8.1.4 of [10].

Table 6.2.4-27: A-MPR for "NS_30"

Parameters
Channel Bandwidth [MHz]	Carrier centre frequency (F_C) [MHz]	Uplink resource allocation	A-MPR [dB]
20	5160¹, 5240²	L = 10 (RIV = 19)	15
	5160¹, 5240²	Any other RIV	16
	5180³, 5320³	L = 10 (RIV = 19)	3
	5180³, 5320³	Any other RIV	3
	5480¹	L = 10 (RIV = 19)	11
	5480¹	Any other RIV	11
	5700³	L = 10 (RIV = 19)	[6]
	5700³	Any other RIV	[6]
	5180³, 5200³, 5220³, 5240³, 5260³, 5280³, 5300³, 5500³, 5520³, 5540³, 5560³, 5580³, 5600³, 5620³, 5640³, 5660³, 5680³	L = 10 (RIV = 19)	1
		Any other RIV	N/A
NOTE 1: Applies also for carrier centre frequencies at a frequency offset of +100 kHz or +200 kHz from the carrier centre frequency stated. NOTE 2: Applies also for carrier centre frequencies at a frequency offset of-200 kHz or -100 kHz from the carrier centre frequency stated. NOTE 3: Applies also for carrier centre frequencies at a frequency offset of -200 kHz, -100 kHz, 100 kHz or +200 kHz from the carrier centre frequency stated. NOTE 4: The carrier centre frequencies and corresponding EARFCN allowed for operation in Band 46 are specified in [12]. The uplink resource allocation is defined in Clause 8.1.4 of [10]. The uplink resource allocation is defined in Clause 8.1.4 of [10].

Table 6.2.4-28: A-MPR for "NS_31"

Parameters
Channel Bandwidth [MHz]	Carrier centre frequency (F_C) [MHz]	Uplink resource allocation	A-MPR [dB]
20	5160¹, 5180³, 5200³, 5220³, 5240²	L = 10 (RIV = 19)	7
	5160¹, 5180³, 5200³, 5220³, 5240²	Any other RIV	7
	5260¹, 5340², 5480¹	L = 10 (RIV = 19)	6
	5260¹, 5340², 5480¹	Any other RIV	6
	5700³, 5825³	L = 10 (RIV = 19)	[6]
	5700³, 5825³	Any other RIV	[6]
	5745³	L = 10 (RIV = 19)	[6]
	5745³	Any other RIV	[6]
	5280³, 5300³, 5320³, 5500³, 5520³, 5540³, 5560³, 5580³, 5600³, 5620³, 5640³, 5660³, 5680³, 5765³, 5785³, 5805³, 5825³	L = 10 (RIV = 19)	2
		Any other RIV	1
NOTE 1: Applies also for carrier centre frequencies at a frequency offset of +100 kHz or +200 kHz from the carrier centre frequency stated. NOTE 2: Applies also for carrier centre frequencies at a frequency offset of-200 kHz or -100 kHz from the carrier centre frequency stated. NOTE 3: Applies also for carrier centre frequencies at a frequency offset of -200 kHz, -100 kHz, 100 kHz or +200 kHz from the carrier centre frequency stated. NOTE 4: The carrier centre frequencies and corresponding EARFCN allowed for operation in Band 46 are specified in [12]. The uplink resource allocation is defined in Clause 8.1.4 of [10].

Table 6.2.4.3-29: A-MPR for “NS_36”

Channel Bandwidth [MHz]	Parameters
5 MHz	Fc [MHz]	700.5 ≤ Fc < 705.5
	RB_start	0		1-4
	L_CRB [RBs]	1	≥ 15	≥ 15	24
	A-MPR [dB]	≤ 2	≤ 4	≤ 1	≤ 3
10 MHz	Fc [MHz]	703 ≤ Fc < 708
	RB_start	0 – 8	9 – 12	13 – 39	40 – 43
	L_CRB [RBs]	> 0	> 12	> 16	> 0
	A-MPR [dB]	≤ 10	≤ 8	≤ 6	≤ 6
15 MHz	Fc [MHz]	Fc = 705.5
	RB_start	0 – 16	17 – 23	24 – 56	57 – 60
	L_CRB [RBs]	> 0	> 12	> 20	< 6
	A-MPR [dB]	≤ 10	≤ 9	≤ 7	≤ 6
NOTE 1: RBstart indicates the lowest RB index of transmitted resource blocks NOTE 2: LCRB is the length of a contiguous resource block allocation NOTE 3: For intra-subframe frequency hopping between two regions, notes 1 and 2 apply on a per slot basis. For intra-slot or intra-subslot frequency hopping between two regions, notes 1 and 2 apply on a per T_{no_hopping} basis. NOTE 4: For intra-subframe frequency hopping between two regions, the larger A-MPR value of the two regions may be applied for both slots in the subframe. For intra-slot frequency hopping between two regions, the larger A-MPR value may be applied for the slot. For intra-subslot frequency hopping between two regions, the larger A-MPR value may be applied for the subslot.

Table 6.2.4.3-30: A-MPR for "NS_38"

Channel Bandwidth

[MHz]

Carrier centre frequency (F_C)

[MHz]

Parameters

Region A

Region B

Region C

Region D

Region E

1428.5 ≤ F_C < 1431.5

RB_start

1– 2

3 – 6

L_CRB [RBs]

≥2

≥ 3

5-7

≥8

A-MPR [dB]

≤ 11

≤ 16

≤ 9

≤ 15

≤ 12

≤ 14

1429.5 ≤ F_C < 1434.5

RB_start

0 – 1

2 – 4

5 – 7

8 – 10

L_CRB [RBs]

≥3

4-6

≥ 7

8-10

≥11

12-14

≥15

A-MPR [dB]

≤ 12

≤ 16

≤ 13

≤ 16

≤ 12

≤ 15

≤ 10

≤ 12

1432 ≤ F_C < 1442

RB_start

1 – 4

5 – 9

10 – 14

15 – 21

L_CRB [RBs]

3-4

≥5

5-8

≥ 9

9-16

≥17

15-23

≥24

24-29

≥30

A-MPR [dB]

≤ 13

≤ 16

≤ 13

≤ 16

≤ 13

≤ 16

≤ 11

≤ 14

≤ 11

≤ 13

1434.5 ≤ F_C < 1447.5

RB_start

0 -1

2 – 7

8 – 17

18 – 23

24 – 30

L_CRB [RBs]

5-10

≥11

8-12

≥ 13

15-25

≥26

26-40

≥41

≥ 36

A-MPR [dB]

≤ 14

≤ 16

≤ 13

≤ 16

≤ 13

≤ 16

≤ 12

≤ 14

≤ 12

1437 ≤ F_C < 1450

RB_start

0 -4

5 – 9

10 – 19

20 – 29

30 – 40

L_CRB [RBs]

6-10

≥11

11-20

≥ 21

17-32

≥33

28-45

≥46

41-54

≥55

A-MPR [dB]

≤ 13

≤ 16

≤ 13

≤ 16

≤ 13

≤ 16

≤ 12

≤ 14

≤ 11

≤ 13

Table 6.2.4.3-31: A-MPR for "NS_39"

Channel Bandwidth [MHz]	Carrier centre frequency (F_C) [MHz]	Parameters	Region A			Region B		Region C
10	1462 < F_C ≤1465	RB_start	43-50
		L_CRB [RBs]	≤ 3	> 3 and ≤ 25	≥ 32
		A-MPR [dB]	≤ 4	≤ 3	≤ 3
15	1456.3 < F_C ≤ 1462.5	RB_start	56-75			64-75		60-75
		L_CRB [RBs]	≥ 36			≥ 13 and ≤ 35		≥ 5 and ≤ 12	< 5
		A-MPR [dB]	≤ 3			≤ 2		≤ 3	≤ 4
20	1450.8 < F_C ≤ 1460	RB_start	71-100			>76
		L_CRB [RBs]	≥ 36			≥ 7 and ≤ 35	< 7
		A-MPR [dB]	≤ 3			≤ 3	≤ 4

For PRACH, PUCCH and SRS transmissions, the allowed A-MPR is according to that specified for PUSCH QPSK modulation for the corresponding transmission bandwidth.

For each subframe, the A-MPR is evaluated per slot and given by the maximum value taken over the transmission(s) within the slot; the maximum A-MPR over the two slots is then applied for the entire subframe.

The normative reference for this requirement is TS 36.101 clause 6.2.4.

Table 6.2.4.3-32: A-MPR for "NS_56"

Channel bandwidth confined to 1627.5- 1637.5MHz
Channel bandwidth	Carrier centre frequency (F_C) (MHz)	Parameters	Region A	Region B	Region C	Region D	Region E	Region F	Region G
5 MHz	1630.0, 1630.3	RB_start	≤ 8	≤ 8	N/A	N/A	N/A	N/A	N/A
		L_CRB [RBs]	≤ 8	> 8	N/A	N/A	N/A	N/A	N/A
		A-MPR [dB]	8	2	N/A	N/A	N/A	N/A	N/A
	1635.0	No A-MPR needed
	1649.0
	1654.0
10 MHz	1632.5	RB_start	≤ 5	≤ 18	≤ 18	≥ 35	≥ 35	≥ 40	≥ 40
		L_CRB [RBs]	≤ 5	≤ 12	> 12	≤ 7	> 7	≤ 7	> 7
		A-MPR [dB]	7	5	7	4	2	5	3
	1651.5	No A-MPR needed

6.2.4.4 Test description

6.2.4.4.1 Initial condition

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies, and channel bandwidths based on E-UTRA operating bands specified in table 5.4.2.1-1. All of these configurations shall be tested with applicable test parameters for each channel bandwidth, and are shown in table 6.2.4.4.1-1 through table 6.2.4.4.1-26. The details of the uplink reference measurement channels (RMCs) are specified in Annex A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.

Table 6.2.4.4.1-1: Test Configuration Table (network signalled value "NS_03")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					NC
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Low range, Mid range, High range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					Lowest, 5MHz, 10MHz, Highest
Test Parameters for NS_03 A-MPR
		Downlink Configuration			Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation		Mod’n	RB allocation
			FDD	TDD		FDD	TDD
1	1.4MHz	N/A for A-MPR testing.			QPSK	6	6
2	1.4MHz				QPSK	5	5
3	1.4MHz				16QAM (Note 6)	5	5
4	3MHz				QPSK	15	15
5	3MHz				QPSK	4	4
6	3MHz				16QAM (Note 6)	15	15
7	3MHz				16QAM (Note 6)	4	4
8	5MHz				QPSK	25	25
9	5MHz				QPSK	8	8
10	5MHz				QPSK	6	6
11	5MHz				16QAM (Note 6)	25	25
12	5MHz				16QAM (Note 6)	8	8
13	10MHz				QPSK	50	50
14	10MHz				QPSK	12	12
15	10MHz				QPSK	6	6
16	10MHz				16QAM (Note 6)	50 (Note 4)	50 (Note 4)
17	10MHz				16QAM (Note 6)	12	12
18	15MHz				QPSK	75	75
19	15MHz				QPSK	16	16
20	15MHz				QPSK	8	8
21	15MHz				16QAM (Note 6)	75 (Note 4)	75 (Note 4)
22	15MHz				16QAM (Note 6)	16	16
23	20MHz				QPSK	100	100
24	20MHz				QPSK	18	18
25	20MHz				QPSK	10	10
26	20MHz				16QAM (Note 6)	100 (Note 4)	100 (Note 4)
27	20MHz				16QAM (Note 6)	18	18
Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 3: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 4: Applies only for UE-Categories ≥2. Note 5: For band 23, above table only applies to mid and high range test frequencies. Low range test frequencies will be covered by NS_11 test configuration table. Note 6: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-2: Test Configuration Table (network signalled value "NS_04")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low range, Mid range, High range Additional test frequencies for Rel-12 to Rel-13 and bit 2 of modifiedMPRbehavior = 0: For 5 MHz bandwidth: 2499.6 MHz, N_UL= 39696 For 10 MHz bandwidth: 2504.1 MHz, N_UL= 39731 For 15 MHz bandwidth: 2510.9 MHz, N_UL= 39799 For 20 MHz bandwidth: 2517.6 MHz, N_UL= 39866 Additional test frequencies for Rel-12 and later and bit 2 of modifiedMPRbehavior = 1: For 5 MHz bandwidth: 2500.6 MHz, N_UL= 39686 For 10 MHz bandwidth: 2504.1 MHz, N_UL= 39731 For 15 MHz bandwidth: 2510.9 MHz, N_UL= 39799 For 20 MHz bandwidth: 2517.6 MHz, N_UL= 39866
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10 MHz, 15 MHz, 20MHz
Test Parameters for NS_04 A-MPR
		Downlink Configuration		Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation TDD	Mod’n	RB allocation TDD	RB_start TDD
1 (Note 6)	5MHz	N/A for A-MPR testing		QPSK	25	0
2 (Note 6)	5MHz			QPSK	8	Note 3
3(Note 6)	5MHz			QPSK	6	Note 3
4 (Note 6)	5MHz			16QAM (Note 5)	25	0
5 (Note 6)	5MHz			16QAM (Note 5)	8	Note 3
6 (Note 6)	10MHz			QPSK	1	0
7 (Note 6)	10MHz			QPSK	12	0
8 (Note 6)	10MHz			QPSK	50	0
9 Note 6)	10MHz			16QAM (Note 5)	50 (Note 4)	0
10 (Note 6)	10MHz			QPSK	24	13
11 (Note 6)	10MHz			16QAM (Note 5)	24	13
12 (Note 6)	10MHz			QPSK	36	13
13 (Note 6)	10MHz			QPSK	12	37
14 (Note 6)	10MHz			QPSK	1	49
15 (Note 6)	15MHz			QPSK	1	0
16 (Note 6)	15MHz			QPSK	16	0
17 (Note 6)	15MHz			QPSK	75	0
18 (Note 6)	15MHz			16QAM (Note 5)	75 (Note 4)	0
19 (Note 6)	15MHz			QPSK	36	19
20 (Note 6)	15MHz			16QAM (Note 5)	36 (Note 4)	19
21 (Note 6)	15MHz			QPSK	50	19
22 (Note 6)	15MHz			QPSK	18	56
23 (Note 6)	15MHz			QPSK	1	74
24 (Note 6)	20MHz			QPSK	1	0
25 (Note 6)	20MHz			QPSK	18	0
26 (Note 6)	20MHz			QPSK	100	0
27 (Note 6)	20MHz			16QAM (Note 5)	100 (Note 4)	0
28 (Note 6)	20MHz			QPSK	50	25
29 (Note 6)	20MHz			16QAM (Note 5)	50 (Note 4)	25
30 (Note 6)	20MHz			QPSK	75	25
31 (Note 6)	20MHz			QPSK	25	75
32 (Note 6)	20MHz			QPSK	1	99
33 (Note 8)	5MHz			QPSK	1	0
34 (Note 8)	5MHz			QPSK	16	9
35 (Note 9)	5MHz			QPSK	25	0
36 (Note 8)	5MHz			16QAM (Note 5)	16	9
37 (Note 9)	5MHz			16QAM (Note 5)	25	0
38 (Note 8)	10MHz			QPSK	1	0
39 (Note 8)	10MHz			QPSK	1	49
40 (Note 8)	10MHz			QPSK	24	0
41 (Note 8)	10MHz			QPSK	40	10
42 (Note 7)	10MHz			QPSK	50	0
43 (Note 7)	10MHz			16QAM (Note 5)	50 (Note 4)	0
44 (Note 8)	15MHz			QPSK	1	0
45 (Note 8)	15MHz			QPSK	1	74
46 (Note 8)	15MHz			QPSK	32	0
47 (Note 8)	15MHz			QPSK	60	15
48 (Note 7)	15MHz			QPSK	75	0
49 (Note 7)	15MHz			16QAM (Note 5)	75 (Note 4)	0
50 (Note 8)	20MHz			QPSK	1	0
51 (Note 8)	20MHz			QPSK	1	99
52 (Note 8)	20MHz			QPSK	36	0
53 (Note 8)	20MHz			QPSK	75	25
54 (Note 7)	20MHz			QPSK	100	0
55 (Note 7)	20MHz			16QAM (Note 5)	100 (Note 4)	0
Note 1: Test Channel Bandwidths are checked separately for E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The configuration ID will be used to map the applicable Test Configuration to be corresponding Test Requirement in subclause 6.2.4 as not all combinations are necessarily required based on the applicability of the UE. Note 3: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 4: Applies only for UE-Categories ≥2. Note 5: The 16QAM configurations shall not apply to UEs which support UL 64QAM. Note 6: Applies only for Rel-11 and earlier. Note 7: Applies only for Rel-12 and later. Note 8: Applies only for Rel-12 and later and Low Range. Note 9: Applies only for Rel-12 and later and Mid, High Range and additional test frequencies.

Table 6.2.4.4.1-3: Test Configuration Table (network signalled value "NS_05")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low range, Mid range In case of Low range: – For 5MHz Channel Bandwidth: 1927.2MHz (NUL = 18072) – For 10 MHz Channel Bandwidth: 1934.7 MHz (NUL = 18147) – For 15 MHz Channel Bandwidth: 1932.5 MHz (NUL = 18125) – For 20 MHz Channel Bandwidth: 1930 MHz (NUL = 18100)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_05 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	5MHz	N/A for A-MPR testing		QPSK	1	0
2	5MHz			QPSK	1	24
3	5MHz			QPSK	25	0
4	10MHz			QPSK	1	0
5	10MHz			QPSK	1	49
6	10MHz			QPSK	12	0
7	10MHz			QPSK	12	38
8	10MHz			QPSK	48	0
9	10MHz			QPSK	48	2
10 (Note 8)	10MHz			QPSK	50	0
11 (Note 8)	10MHz			16QAM (Note 7)	50 (Note 4)	0
12 (Note 9)	15MHz			QPSK	1	8
13 (Note 9)	15MHz			QPSK	1	66
14 (Note 9)	15MHz			QPSK	16	8
15 (Note 9)	15MHz			QPSK	16	51
16 (Note 9)	15MHz			QPSK	30	8
17 (Note 9)	15MHz			QPSK	30	37
18 (Note 9)	20MHz			QPSK	1	24
19 (Note 9)	20MHz			QPSK	1	75
20 (Note 9)	20MHz			QPSK	18	24
21 (Note 9)	20MHz			QPSK	18	58
22 (Note 9)	20MHz			QPSK	24	24
23 (Note 9)	20MHz			QPSK	24	52
24 (Note 10)	15MHz			QPSK	1	0
25 (Note 10)	15MHz			QPSK	1	74
26 (Note 10)	15MHz			QPSK	16	0
27 (Note 10)	15MHz			QPSK	16	59
28 (Note 10)	15MHz			QPSK	48	0
29 (Note 10)	15MHz			QPSK	48	27
30 (Note 10)	15MHz			QPSK	75	0
31 (Note 10)	15MHz			16QAM (Note 7)	75 (Note 4)	0
32 (Note 10)	20MHz			QPSK	1	0
33 (Note 10)	20MHz			QPSK	1	99
34 (Note 10)	20MHz			QPSK	18	0
35 (Note 10)	20MHz			QPSK	18	82
36 (Note 10)	20MHz			QPSK	48	0
37 (Note 10)	20MHz			QPSK	48	52
38 (Note 10)	20MHz			QPSK	100	0
39 (Note 10)	20MHz			16QAM (Note 7)	100 (Note 4)	0
40 (Note 11)	10MHz			QPSK	50	0
41 (Note 11)	10MHz			16QAM (Note 7)	50 (Note 4)	0
42 (Note 11)	15MHz			QPSK	1	0
43 (Note 11)	15MHz			QPSK	75	0
44 (Note 11)	15MHz			QPSK	16	8
45 (Note 11)	15MHz			QPSK	30	8
46 (Note 11)	15MHz			QPSK	54	8
47 (Note 11)	15MHz			QPSK	64	8
48 (Note 11)	15MHz			QPSK	1	74
49 (Note 11)	15MHz			QPSK	6	69
50 (Note 11)	15MHz			QPSK	8	67
51 (Note 11)	20MHz			QPSK	1	0
52 (Note 11)	20MHz			QPSK	100	0
53 (Note 11)	20MHz			QPSK	18	24
54 (Note 11)	20MHz			QPSK	24	24
55 (Note 11)	20MHz			QPSK	40	24
56 (Note 11)	20MHz			QPSK	50	24
57 (Note 11)	20MHz			QPSK	72	24
58 (Note 11)	20MHz			QPSK	1	99
59 (Note 11)	20MHz			QPSK	6	94
60 (Note 11)	20MHz			QPSK	24	76
61 (Note 12)	10MHz			QPSK	50	0
62 (Note 12)	10MHz			16QAM (Note 7)	50 (Note 4)	0
63 (Note 12)	15MHz			QPSK	1	0
64 (Note 12)	15MHz			QPSK	1	74
65 (Note 12)	15MHz	QPSK	16	0
66 (Note 12)	15MHz	QPSK	16	59
67 (Note 12)	15MHz	QPSK	48	0
68 (Note 12)	15MHz	QPSK	48	27
69 (Note 12)	15MHz	QPSK	75	0
70 (Note 12)	15MHz	16QAM (Note 7)	75 (Note 4)	0
71 (Note 12)	20MHz	QPSK	1	0
72 (Note 12)	20MHz	QPSK	1	99
73 (Note 12)	20MHz	QPSK	18	0
74 (Note 12)	20MHz	QPSK	18	82
75 (Note 12)	20MHz	QPSK	48	0
76 (Note 12)	20MHz	QPSK	48	52
77 (Note 12)	20MHz	QPSK	100	0
78 (Note 12)	20MHz	16QAM (Note 7)	100 (Note 4)	0
Note 1: Void Note 2: Void Note 3: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 4: Applies only for UE-Categories ≥2. Note 5: Void. Note 6: Void. Note 7: The 16QAM configurations shall not apply to UEs which support UL 64QAM. Note 8: Applies when bit number 1 in modifiedMPRbehavior = 0 (Rel-11 minimum requirements apply) for Band1 and not available for Band65. Note 9: Applies for low range and when bit number 1 in modifiedMPRbehavior = 0 (Rel-11 minimum requirements apply) for Band1 and not available for Band65. Note 10: Applies for mid range and when bit number 1 in modifiedMPRbehavior = 0 (Rel-11 minimum requirements apply) for Band1 and not available for Band65. Note 11: Applies only for low range and when bit number 1 in modifiedMPRbehavior = 1 (Rel-12 minimum requirements apply) for Band1 and low range for Band65. Note 12: Applies only for mid range and when bit number 1 in modifiedMPRbehavior = 1 (Rel-12 minimum requirements apply) for Band1 and mid range for Band65. Note 13: ModifiedMPRbehavior is defined in annex J.1.

Table 6.2.4.4.1-4: Test Configuration Table (network signalled value "NS_06")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low range, Mid range, High range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				Lowest, 5MHz, 10MHz
Test Parameters for NS_06 A-MPR
		Downlink Configuration		Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	1.4MHz	N/A for A-MPR testing		QPSK	6
2	1.4MHz			QPSK	5
3	1.4MHz			16QAM (Note 4)	5
4	5MHz			QPSK	25
5	5MHz			QPSK	8
6	5MHz			16QAM (Note 4)	8
7	10MHz			QPSK	50
8	10MHz			QPSK	12
9	10MHz			16QAM (Note 4)	12
Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 3: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-5: Test Configuration Table (network signalled value "NS_07")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Mid range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				10MHz
Test Parameters for NS_07 A-MPR
		Downlink Configuration		Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	10MHz	N/A for A-MPR testing		QPSK	1	0
2	10MHz			QPSK	8	0
3	10MHz			QPSK	6	13
4	10MHz			QPSK	20	13
5	10MHz			QPSK	12	13
6	10MHz			16QAM (Note 3)	36 (Note 2)	13
7	10MHz			QPSK	16	19
8	10MHz			QPSK	12	19
9	10MHz			16QAM (Note 3)	16	19
10	10MHz			QPSK	30	19
11	10MHz			16QAM (Note 3)	30 (Note 2)	19
12	10MHz			QPSK	6	43
13	10MHz			QPSK	2	48
14	10MHz			QPSK	50	0
15	10MHz			QPSK	12	0
16	10MHz			16QAM (Note 3)	50 (Note 2)	0
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-6: Test Configuration Table (network signalled value "NS_08")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				High range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz
Test Parameters for NS_08 A-MPR
		Downlink Configuration		Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for A-MPR testing		QPSK	1
2	5MHz			QPSK	8
3	5MHz			QPSK	25
4	10MHz			QPSK	1
5	10MHz			QPSK	12
6	10MHz			QPSK	40
7	10MHz			QPSK	50
8	10MHz			16QAM (Note 5)	50 (Note 4)
9	15MHz			QPSK	1
10	15MHz			QPSK	16
11	15MHz			QPSK	40
12	15MHz			QPSK	75
13	15MHz			16QAM (Note 5)	75 (Note 4)
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 3: The RB_start of partial RB allocation shall be RB# 0 and RB# (max + 1 – RB allocation) of the channel bandwidth Note 4: Applies only for UE-Categories ≥2. Note 5: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-7: Test Configuration Table (network signalled value "NS_09")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				High range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for A-MPR testing		QPSK	1
2	5MHz			QPSK	8
3	5MHz			QPSK	25
4	10MHz			QPSK	1
5	10MHz			QPSK	12
6	10MHz			QPSK	40
7	10MHz			QPSK	50
8	10MHz			16QAM (Note 5)	50 (Note 4)
9	15MHz			QPSK	1
10	15MHz			QPSK	16
11	15MHz			QPSK	40
12	15MHz			QPSK	54
13	15MHz			QPSK	75
14	15MHz			16QAM (Note 5)	75 (Note 4)
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 3: The RB_start of partial RB allocation shall be RB# 0 and RB# (max + 1 – RB allocation) of the channel bandwidth Note 4: Applies only for UE-Categories ≥2. Note 5: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-8: Test Configuration Table (network signalled value "NS_10")

Void, not tested

Table 6.2.4.4.1-9: Test Configuration Table (network signalled value "NS_11")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				For 3 MHz Channel Bandwidth: a. 2001.5 MHz (N_UL= 25515) b. 2004.5 MHz (N_UL = 25545) For 5 MHz Channel Bandwidth a. 2002.5 MHz (N_UL = 25525) b. 2004.5 MHz (N_UL = 25545) c. 2007.5 MHz (N_UL = 25575) For 10 MHz Channel Bandwidth a. 2005 MHz (N_UL = 25550) b. 2005.5 MHz (N_UL = 25555) c. 2015 MHz (N_UL = 25650) For 15 MHz Channel Bandwidth a. 2007.5 MHz (N_UL = 25575) b. 2012.5 MHz (N_UL = 25625) For 20 MHz Channel Bandwidth a. 2010 MHz (N_UL = 25600)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				3MHz, 5MHz, 10MHz, 15MHz, 20MHz
				3MHz, 5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_11 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	3MHz	N/A for A-MPR testing		QPSK	6
2	3MHz			QPSK	15
3	3MHz			16QAM (Note 4)	6
4	3MHz			16QAM (Note 4)	15
5	5MHz			QPSK	1
6	5MHz			QPSK	8
7	5MHz			QPSK	25
8	5MHz			16QAM (Note 4)	8
9	5MHz			16QAM (Note 4)	25
10	10MHz			QPSK	1
11	10MHz			QPSK	12
12	10MHz			QPSK	50
13	10MHz			16QAM (Note 4)	12
14	10MHz			16QAM (Note 4)	50
14	10MHz			16QAM (Note 4)	(Note 3)
15	15MHz			QPSK	1
16	15MHz			QPSK	8
17	15MHz			QPSK	25
18	15MHz			QPSK	30
19	15MHz			QPSK	75
20	15MHz			16QAM (Note 4)	8
21	15MHz			16QAM (Note 4)	25
22	15MHz			16QAM (Note 4)	30
23	15MHz			16QAM (Note 4)	75
24	20MHz			QPSK	1
25	20MHz			QPSK	10
26	20MHz			QPSK	25
27	20MHz			QPSK	100
28	20MHz			16QAM (Note 4)	10
29	20MHz			16QAM (Note 4)	25
30	20MHz			16QAM (Note 4)	100
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 3: Applies only for UE-Categories ≥2. Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-10: Test Configuration Table (network signalled value "NS_12")

Initial Conditions
Test Environment				NC
(as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies				For 1.4 MHz Channel Bandwidth: UL 814.9 MHz (N_UL = 26699) For 3 MHz Channel Bandwidth: UL 815.7 MHz (N_UL = 26707) For 5 MHz Channel Bandwidth: UL 816.7 MHz (N_UL = 26717) For 10 MHz Channel Bandwidth: UL 819.2 MHz (N_UL = 26742) For 15 MHz Channel Bandwidth: UL 821.7 MHz (N_UL = 26767)
(as specified in TS 36.508 [7] subclause 4.3.1)
Test Channel Bandwidths				1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz
(as specified in TS 36.508 [7] subclause 4.3.1)				1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	1.4 MHz	N/A for A-MPR testing.		QPSK	1	0
2	1.4 MHz			QPSK	6	0
3	1.4 MHz			QPSK	1	1
4	1.4 MHz			QPSK	5	1
5	1.4 MHz			16QAM (Note 3)	6	0
6 (Note 1)	3 MHz			QPSK	4	0
7 (Note 1)	3 MHz			QPSK	10	0
8	3 MHz			QPSK	4	4
9	3 MHz			QPSK	10	4
10 (Note 1)	3 MHz			16QAM (Note 3)	15	0
11	5 MHz			QPSK	8	0
12	5 MHz			QPSK	15	0
13	5 MHz			QPSK	8	7
14 (Note 1)	5 MHz			QPSK	15	7
15	5 MHz			16QAM (Note 3)	25	0
16 (Note 2)	10 MHz			QPSK	18	0
17 (Note 2)	10 MHz			QPSK	18	16
18 (Note 2)	10 MHz			16QAM (Note 4, 3)	50	0
19 (Note 2)	15 MHz			QPSK	30	0
20 (Note 2)	15 MHz			QPSK	30	31
21 (Note 2)	15 MHz			16QAM (Note 4, 3)	75	0
Note 1: Only for UEs of Rel-11 and earlier Note 2: Only for UEs of Rel-12 and later Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM. Note 4 : Applies only for UE-Categories ≥2.

Table 6.2.4.4.1-11: Test Configuration Table (network signalled value "NS_13")

Initial Conditions
Test Environment				NC
(as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies				For 1.4 MHz Channel Bandwidth: UL 819.7 MHz (N_UL = 26747) For 3 MHz Channel Bandwidth: UL 820.5 MHz (N_UL = 26755) For 5 MHz Channel Bandwidth: UL 821.5 MHz (N_UL = 26765)
(as specified in TS 36.508 [7] subclause 4.3.1)
Test Channel Bandwidths				1.4 MHz, 3MHz and 5 MHz
(as specified in TS 36.508 [7] subclause 4.3.1)				1.4 MHz, 3MHz and 5 MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1 (Note 1)	1.4 MHz	N/A for A-MPR testing.		QPSK	6	0
2 (Note 1)	3 MHz			QPSK	15	0
3	5 MHz			QPSK	1	0
4	5 MHz			QPSK	25	0
5	5 MHz			QPSK	15	0
6	5 MHz			QPSK	15	7
7	5 MHz			16QAM (Note 2)	25	0
Note 1: Only for UEs of Rel-12 and later Note 2: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-12: Test Configuration Table (network signalled value "NS_14")

Initial Conditions
Test Environment				NC
(as specified in TS 36.508 [7] subclause 4.1)				NC
Test Frequencies				For 10 MHz Channel Bandwidth: UL 829 MHz (N_UL = 26840) For 15 MHz Channel Bandwidth: Mid range
(as specified in TS 36.508 [7] subclause 4.3.1)
Test Channel Bandwidths				10 MHz, 15 MHz
(as specified in TS 36.508 [7] subclause 4.3.1)				10 MHz, 15 MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation	Mod’n	RB allocation FDD	RBstart FDD
1	10 MHz	N/A for A-MPR testing.		QPSK	1	0
2	10 MHz			QPSK	25	0
3	10 MHz			QPSK	50	0
4	10 MHz			QPSK	25	1
5 (Note 1)	10 MHz			16QAM (Note 2)	50	0
6	15 MHz			QPSK	8	0
7	15 MHz			QPSK	25	0
8	15 MHz			QPSK	75	0
9	15 MHz			QPSK	50	15
10 (Note 1)	15 MHz			16QAM (Note 2)	75	0
Note 1: Applies only for UE-Categories ≥2. Note 2: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-13: Test Configuration Table (network signalled value "NS_15")

Initial Conditions

Test Environment

(as specified in TS 36.508 [7] subclause 4.1)

Test Frequencies

(as specified in TS 36.508 [7] subclause 4.3.1)

For 1.4 MHz Channel Bandwidth: High range

For 3 MHz Channel Bandwidth: UL 843.5 MHz (N_UL = 26985) or High range

For 5 MHz Channel Bandwidth: UL 842.5 MHz (N_UL = 26975) or High range

For 10 MHz Channel Bandwidth: UL 840 MHz (N_UL = 26950) or High range

For 15 MHz Channel Bandwidth: UL 837.5 MHz (N_UL = 26925) or High range

Test Channel Bandwidths

(as specified in TS 36.508 [7] subclause 4.3.1)

1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz

Test Parameters for Channel Bandwidths

Downlink Configuration

Uplink Configuration

Configuration ID

Ch BW

Mod’n

RB allocation

Mod’n

RB allocation FDD

RBstart FDD

1 (note 3)

1.4 MHz

N/A for A-MPR testing.

QPSK

2 (note 3)

1.4 MHz

16QAM

(Note 4)

3 (note 3)

3 MHz

QPSK

4 (note 3)

3 MHz

QPSK

5 (note 3)

3 MHz

16QAM

(Note 4)

6 (note 2)

3 MHz

QPSK

7 (note 3)

5 MHz

QPSK

8 (note 3)

5 MHz

QPSK

9 (note 3)

5 MHz

16QAM

(Note 4)

10 (note 2)

5 MHz

QPSK

11 (note 2)

5 MHz

QPSK

12 (note 3)

10 MHz

QPSK

13 (note 3)

10 MHz

QPSK

14 (note 3)

10 MHz

QPSK

15 (note 3)

10 MHz

QPSK

16 (note 3)

10 MHz

QPSK

17 (note 3)

10 MHz

QPSK

18 (note 1, 3)

10 MHz

16QAM

(Note 4)

19 (note 2)

10 MHz

QPSK

20 (note 2)

10 MHz

QPSK

21 (note 3)

15 MHz

QPSK

22 (note 3)

15 MHz

QPSK

23 (note 3)

15 MHz

QPSK

24 (note 1, 3)

15 MHz

16QAM

(Note 4)

25 (note 2)

15 MHz

QPSK

26 (note 2)

15 MHz

QPSK

Note 1: Applies only for UE-Categories ≥2.

Note 2: Applicable only test frequency < high range.

Note 3: Applicable only to high range frequency testing.

Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-14: Test Configuration Table (network signalled value "NS_16")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)							NC
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)							For 1.4 MHz Channel Bandwidth: Low range For 3 MHz Channel Bandwidth: Low range, 810 MHz (N_UL= 27070) For 5 MHz Channel Bandwidth: Low range, 811 MHz (N_UL= 27080), 814.5 MHz (N_UL= 27115) For 10 MHz Channel Bandwidth: Low range, 813.5 MHz (N_UL= 27105), 817 MHz (N_UL= 27140)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)							1.4 MHz, 3 MHz, 5 MHz, 10 MHz
Test Parameters for Channel Bandwidths
				Downlink Configuration			Uplink Configuration
Configuration ID		Ch BW		Mod’n	RB allocation		Mod’n		RB allocation FDD		RBstart FDD
1	1.4 MHz		N/A for A-MPR testing.			QPSK		1		0
2	1.4 MHz					QPSK		6		0
3	1.4 MHz					16QAM (Note 4)		6		0
4	3 MHz					QPSK		1		0
5		3 MHz					QPSK		12		1
6		3 MHz					QPSK		15		0
7		3 MHz					16QAM (Note 4)		15		0
8		5 MHz					QPSK		1		0
9		5 MHz					QPSK		12		2
10		5 MHz					QPSK		18		2
11		5 MHz					QPSK		20		0
12		5 MHz					QPSK		20		2
13		5 MHz					QPSK		25		0
14		5 MHz					16QAM (Note 4)		25		0
15		10 MHz					QPSK		1		0
16 (Note 2)	10 MHz					QPSK		1		10
17 (Note 2)		10 MHz					QPSK		20		0
18 (Note 2)		10 MHz					QPSK		27		15
19 (Note 2)		10 MHz					QPSK		32		15
20		10 MHz					QPSK		32		0
21		10 MHz					QPSK		50		0
22 (Note 1)		10 MHz					16QAM (Note 4)		50		0
23 (Note 3)		10 MHz					QPSK		40		0
24 (Note 3)		10 MHz					QPSK		40		1
Note 1: Applies only for UE-Categories ≥2. Note 2: Applies only for 10 MHz channel for Low Range, and 813.5 MHz Note 3: Applies only for 10 MHz channel for 817 MHz range Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-15: Test Configuration Table (network signalled value "NS_17")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Mid range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for A-MPR testing		QPSK	1
2	5MHz			QPSK	8
3	5MHz			QPSK	25
4	5MHz			16QAM (Note 4)	25 (Note 3)
5	10MHz			QPSK	1
6	10MHz			QPSK	12
7	10MHz			QPSK	50
8	10MHz			16QAM (Note 4)	50 (Note 3)
Note 1: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 2: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 3: Applies only for UE-Categories ≥2. Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-16: Test Configuration Table (network signalled value "NS_18")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for A-MPR testing		QPSK	1
2	5MHz			QPSK	8
3	5MHz			QPSK	25
4	5MHz			16QAM (Note 4)	25 (Note 3)
5	10MHz			QPSK	1
6	10MHz			QPSK	12
7	10MHz			QPSK	50
8	10MHz			16QAM (Note 4)	50 (Note 3)
9	15MHz			QPSK	1
10	15MHz			QPSK	16
11	15MHz			QPSK	75
12	15MHz			16QAM (Note 4)	75 (Note 3)
13	20MHz			QPSK	1
14	20MHz			QPSK	18
15	20MHz			QPSK	100
16	20MHz			16QAM (Note 4)	100 (Note 3)
Note 1: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 2: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 3: Applies only for UE-Categories ≥2. Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-17: Test Configuration Table (network signalled value "NS_19")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				3MHz, 10MHz, 15MHz, 20MHz
Test Parameters for Channel Bandwidths
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	3MHz	N/A		QPSK	15
2	3MHz			16QAM (Note 4)	15 (Note 3)
3	10MHz			QPSK	40
4	10MHz			16QAM (Note 4)	40 (Note 3)
5	15MHz			QPSK	1
6	15MHz			QPSK	18
7	15MHz			QPSK	36
8	15MHz			QPSK	45
9	15MHz			16QAM (Note 4)	45 (Note 3)
10	20MHz			QPSK	1
11	20MHz			QPSK	40
12	20MHz			QPSK	45
13	20MHz			QPSK	50
14	20MHz			16QAM (Note 4)	50 (Note 3)
Note 1: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 2: The RBstart of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 3: Applies only for UE-Categories ≥2. Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-18: Test Configuration Table (network signalled value "NS_20")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				For 5 MHz Channel Bandwidth a. 2002.5 MHz (N_UL = 25525) b. 2007.5 MHz (N_UL = 25575) c. 2012.5 MHz (N_UL = 25625) d. 2017.5 MHz (N_UL = 25675) For 10 MHz Channel Bandwidth a. 2005 MHz (N_UL = 25550) b. 2015 MHz (N_UL = 25650) For 15 MHz Channel Bandwidth a. 2012.5 MHz (N_UL = 25625) For 20 MHz Channel Bandwidth a. 2010 MHz (N_UL = 25600)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_20 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for A-MPR testing		QPSK	8
2	5MHz			QPSK	15
3	5MHz			QPSK	25
4	5MHz			16QAM (Note 4)	15
5	5MHz			16QAM (Note 4)	25
6	10MHz			QPSK	8
7	10MHz			QPSK	12
8	10MHz			QPSK	50
9	10MHz			16QAM (Note 4)	12
10	10MHz			16QAM (Note 4)	50
10	10MHz			16QAM (Note 4)	(Note 3)
11	15MHz			QPSK	6
12	15MHz			QPSK	25
13	15MHz			QPSK	36
14	15MHz			QPSK	75
15	15MHz			16QAM (Note 4)	25
16	15MHz			16QAM (Note 4)	36
17	15MHz			16QAM (Note 4)	75
18	20MHz			QPSK	8
19	20MHz			QPSK	18
20	20MHz			QPSK	25
21	20MHz			QPSK	75
22	20MHz			QPSK	100
23	20MHz			16QAM (Note 4)	18
24	20MHz			16QAM (Note 4)	25
25	20MHz			16QAM (Note 4)	75
26	20MHz			16QAM (Note 4)	100
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 3: Applies only for UE-Categories ≥2. Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-19: Test Configuration Table (network signalled value "NS_21")

Initial Conditions

Test Environment

(as specified in TS 36.508 [7] subclause 4.1)

Test Frequencies

(as specified in TS 36.508 [7] subclause 4.3.1)

Low range or High range

Test Channel Bandwidths

(as specified in TS 36.508 [7] subclause 4.3.1)

5 MHz, 10 MHz

Test Parameters for Channel Bandwidths

Downlink Configuration

Uplink Configuration

Configuration ID

Ch BW

Mod’n

RB allocation

Mod’n

RB allocation FDD

RBstart FDD

1 (note 2)

5 MHz

QPSK

2 (note 2)

5 MHz

QPSK

3 (note 2)

10 MHz

QPSK

4 (note 3)

10 MHz

QPSK

5 (note 2)

10 MHz

QPSK

6 (note 3)

10 MHz

QPSK

7 (note 3)

10 MHz

QPSK

8 (note 1, 3)

10 MHz

16QAM

(Note 4)

Note 1: Applies only for UE-Categories ≥2.

Note 2: Applicable only to low range frequency testing.

Note 3: Applicable only to high range frequency testing.

Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-20: Test Configuration Table (network signalled value "NS_22")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range, Mid Range, High Range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_22 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation TDD	RB_start TDD
1	5MHz	N/A for A-MPR testing		QPSK	1	0
2	5MHz			QPSK	25	0
3	5MHz			QPSK	1	24
4	5MHz			16QAM	1	0
5	5MHz			16QAM	1	24
6	10MHz			QPSK	50	0
7	10MHz			QPSK	36	0
8	10MHz			QPSK	1	0
9	10MHz			QPSK	1	49
10	10MHz			16QAM	1	0
11	10MHz			16QAM	1	49
12	15MHz			QPSK	75	0
13	15MHz			QPSK	50	0
14	15MHz			QPSK	1	0
15	15MHz			QPSK	1	74
16	15MHz			16QAM	1	0
17	15MHz			16QAM	1	74
18	20MHz			QPSK	100	0
19	20MHz			QPSK	64	0
20	20MHz			QPSK	1	0
21	20MHz			QPSK	1	99
22	20MHz			16QAM	1	0
23	20MHz			16QAM	1	99
Note 1: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-21: Test Configuration Table (network signalled value "NS_23")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low Range, Mid Range, High Range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_23 A-MPR
		Downlink Configuration		Uplink Configuration
Configuration ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation TDD	RB_start TDD
1	5MHz	N/A for A-MPR testing		QPSK	1	0
2	5MHz			QPSK	1	24
3	5MHz			QPSK	25	0
4	5MHz			16QAM	1	0
5	5MHz			16QAM	1	24
6	10MHz			QPSK	50	0
7	15MHz			QPSK	75	0
8	20MHz			QPSK	100	0
Note 1: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-22: Test Configuration Table (network signalled value "NS_24")

	Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)						Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)						Refer to F_ULin test parameters with following: 5 MHz CH BW: 1985 MHz (N_UL = 131722) 2007.5 MHz (N_UL= high range) 10 MHz CH BW: 1980 MHz (N_UL = 131672) 1990 MHz (N_UL = 131772) 2005 MHz (N_UL= high range) 15 MHZ CH BW: 1980 MHz (N_UL = 131672) 1990 MHz (N_UL = 131772) 2002.5 MHz (N_UL= high range) 20 MHz CH BW: 2000 MHz (N_UL= high range)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)						5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_24 A-MPR
				Downlink Configuration		Uplink Configuration
Configuration ID		F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1		2007.5	5MHz	N/A for A-MPR testing		QPSK	1	0
2		2007.5	5MHz			QPSK	8	17
3		2007.5	5MHz			QPSK	25	0
4 (Notes 2,3)		2007.5	5MHz			16QAM	25	0
5		1985	5MHz			QPSK	8	17
6		1980	10MHz			QPSK	12	1
7 (Notes 2,3)		1980	10MHz			16QAM	50	0
8		1980	10MHz			QPSK	48	2
9		1980	10MHz			QPSK	25	25
10		1980	10MHz			QPSK	1	49
11		1980	10MHz			QPSK	12	38
12 (Notes 2,3)		1980	10MHz			16QAM	12	38
13		1980	10MHz			QPSK	3	47
14		1980	10MHz			QPSK	8	1
15		1990	10MHz			QPSK	1	0
16		1990	10MHz			QPSK	12	38
17 (Notes 2,3)		1990	10MHz			16QAM	50	0
18		2005	10MHz			QPSK	12	38
19		2005	10MHz			QPSK	50	0
20 (Notes 2,3)		2005	10MHz			16QAM	50	0
21		1980	15MHz			QPSK	1	11
22		1980	15MHz			QPSK	16	11
23		1980	15MHz			QPSK	45	11
24 (Notes 2,3)		1980	15MHz			16QAM	50	0
25		1980	15MHz			QPSK	16	28
26		1980	15MHz			QPSK	16	59
27		1980	15MHz			QPSK	60	15
28		1980	15MHz			QPSK	30	12
29		2002.5	15MHz			QPSK	1	0
30		2002.5	15MHz			QPSK	16	59
31 (Notes 2,3)		2002.5	15MHz			16QAM	16	59
32 (Notes 2,3)		2002.5	15MHz			16QAM	75	0
33		2000	20MHz			QPSK	1	0
34		2000	20MHz			QPSK	18	82
35 (Notes 2,3)		2000	20MHz			16QAM	18	82
36 (Notes 2,3)		2000	20MHz			16QAM	100	0
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-23: Test Configuration Table (network signalled value "NS_25")

	Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)						Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)						Refer to F_ULin test parameters with following: 5 MHz CH BW: 2007.5 MHz (N_UL= high range) 10 MHz CH BW: 1980 MHz (N_UL = 131672) 1990 MHz (N_UL = 131772) 2005 MHz (N_UL= high range) 15 MHZ CH BW: 1980 MHz (N_UL = 131672) 1990 MHz (N_UL = 131772) 2002.5 MHz (N_UL= high range) 20 MHz CH BW: 2000 MHz (N_UL= high range)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)						5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_25 A-MPR
				Downlink Configuration		Uplink Configuration
Configuration ID		F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1		2007.5	5MHz	N/A for A-MPR testing		QPSK	25	0
2 (Notes 2,3)		2007.5	5MHz			16QAM	25	0
3		2007.5	5MHz			QPSK	8	9
4		2007.5	5MHz			QPSK	1	24
5		2007.5	5MHz			QPSK	8	17
6 (Notes 2,3)		2007.5	5MHz			16QAM	8	17
7		1980	10MHz			QPSK	12	1
8 (Notes 2,3)		1980	10MHz			16QAM	50	0
9 (Notes 2,3)		1980	10MHz			16QAM	48	2
10		1980	10MHz			QPSK	25	25
11		1980	10MHz			QPSK	1	49
12		1980	10MHz			QPSK	12	38
13		1990	10MHz			QPSK	12	0
14		1990	10MHz			QPSK	25	0
15		1990	10MHz			QPSK	50	0
16 (Notes 2,3)		1990	10MHz			16QAM	25	0
17		1990	10MHz			QPSK	48	2
18		1990	10MHz			QPSK	30	19
19 (Notes 2,3)		1990	10MHz			16QAM	30	19
20		1990	10MHz			QPSK	12	31
21		2005	10MHz			QPSK	1	0
22		2005	10MHz			QPSK	12	6
23		2005	10MHz			QPSK	50	0
24 (Notes 2,3)		2005	10MHz			16QAM	50	0
25		2005	10MHz			QPSK	40	10
26 (Notes 2,3)		2005	10MHz			16QAM	40	10
27		2005	10MHz			QPSK	32	18
28 (Notes 2,3)		2005	10MHz			16QAM	32	18
29		2005	10MHz			QPSK	12	23
30		1980	15MHz			QPSK	16	4
31		1980	15MHz			QPSK	75	0
32		1980	15MHz			QPSK	60	15
33 (Notes 2,3)		1980	15MHz			16QAM	40	35
34		1980	15MHz			QPSK	1	74
35		1980	15MHz			QPSK	12	63
36		1980	15MHz			QPSK	16	55
37		2002.5	15MHz			QPSK	1	0
38		2002.5	15MHz			QPSK	16	0
39 (Notes 2,3)		2002.5	15MHz			16QAM	16	0
40 (Notes 2,3)		2002.5	15MHz			16QAM	1	0
41		1980	20MHz			QPSK	1	0
42		1980	20MHz			QPSK	18	0
43 (Notes 2,3)		1980	20MHz			16QAM	100	0
44		1980	20MHz			QPSK	64	36
45		1980	20MHz			QPSK	18	72
46 (Notes 2,3)		1980	20MHz			16QAM	54	46
47		1980	20MHz			QPSK	18	55
48		2000	20MHz			QPSK	1	0
49		2000	20MHz			QPSK	18	72
50 (Notes 2,3)		2000	20MHz			16QAM	18	72
51 (Notes 2,3)		2000	20MHz			16QAM	100	0
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-24: Test Configuration Table (network signalled value "NS_27")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to Frequency columnin test parameters
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_27 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	Frequency	Ch BW	Mod’n	RB allocation TDD	Mod’n	RB allocation TDD	RB_start TDD
1	Low/Mid	5MHz	N/A for A-MPR testing		QPSK	1	0
2	High	5MHz			QPSK	1	24
3	Low/Mid/High	5MHz			QPSK	25	0
4	Low/Mid/High	5MHz			16QAM	25	0
5	Low/Mid	10MHz			QPSK	1	0
6	High	10MHz			QPSK	1	49
7	Low/Mid/High	10MHz			QPSK	50	0
8 (Note 2)	Low/Mid/High	10MHz			16QAM	50	0
9	Low/Mid	15MHz			QPSK	1	0
10	Low	15MHz			QPSK	1	7
11	Low/Mid	15MHz			QPSK	16	0
12	High	15MHz			QPSK	1	74
13	High	15MHz			QPSK	1	67
14	High	15MHz			QPSK	16	0
15	Low/Mid/High	15MHz			QPSK	75	0
16 (Note 2)	Low/Mid/High	15MHz			16QAM	75	0
17	Low/Mid	20MHz			QPSK	1	0
18	Low	20MHz			QPSK	1	13
19	Low	20MHz			QPSK	1	16
20	Low/Mid	20MHz			QPSK	24	0
21	High	20MHz			QPSK	1	99
22	High	20MHz			QPSK	1	86
23	High	20MHz			QPSK	1	83
24	High	20MHz			QPSK	24	0
25	Low/Mid/High	20MHz			QPSK	100	0
26 (Note 2)	Low/Mid/High	20MHz			16QAM	100	0
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-25: Test Configuration Table (network signalled value "NS_35")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)				Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)				Low range, Mid range, High range
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)				5MHz, 10MHz, 15MHz, 20MHz
Test Parameters for NS_35 A-MPR
		Downlink Configuration		Uplink Configuration
Configura-tion ID	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD
1	5MHz	N/A for A-MPR testing		QPSK	25
2	5MHz			QPSK	8
3	5MHz			16QAM (Note 4)	8
4	10MHz			QPSK	50
5	10MHz			QPSK	12
6	10MHz			16QAM (Note 4)	12
7	15MHz			QPSK	75
8	15MHz			QPSK	16
9	15MHz			16QAM (Note 4)	16
10	20MHz			QPSK	100
11	20MHz			QPSK	18
12	20MHz			16QAM (Note 4)	18
Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 3: The RB_start of partial RB allocation shall be RB# 0 and RB# (max +1 – RB allocation) of the channel bandwidth. Note 4: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-26: Test Configuration Table (network signalled value "NS_36")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 700.5 MHz (N_UL = low range) 705.5 MHz (N_UL=132747) 10 MHz CH BW: 703 MHz (N_UL = low range) 708 MHz (N_UL = 132772) 15 MHz CH BW: 705.5 MHz (N_UL = low range) 710.5 MHz (N_UL =132797 )
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz, 15MHz
Test Parameters for NS_36 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	700.5	5MHz	N/A for A-MPR testing		QPSK	1	0
2	700.5	5MHz			QPSK	25	0
3	700.5	5MHz			QPSK	20	1
4	700.5	5MHz			QPSK	24	1
5	700.5	5MHz			QPSK	12	0
6 (Notes 2,3)	700.5	5MHz			16QAM	12	0
7	705.5	5MHz			QPSK	25	0
8 (Notes 2,3)	705.5	5MHz			16QAM	25	0
9	703	10MHz			QPSK	50	0
10	703	10MHz			QPSK	1	0
11	703	10MHz			QPSK	40	9
12	703	10MHz			QPSK	36	13
13	703	10MHz			QPSK	10	40
14	703	10MHz			QPSK	6	44
15	708	10MHz			QPSK	50	0
16 (Notes 2,3)	708	10MHz			16QAM	50	0
17	705.5	15MHz			QPSK	75	0
18	705.5	15MHz			QPSK	50	17
19	705.5	15MHz			QPSK	50	24
20	705.5	15MHz			QPSK	1	57
21	705.5	15MHz			QPSK	10	17
22	705.5	15MHz			QPSK	18	24
23 (Notes 2,3)	705.5	15MHz			16QAM	18	24
24	710.5	15MHz			QPSK	75	0
25	710.5	15MHz			16QAM	75	0
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Table 6.2.4.4.1-27: Test Configuration Table (network signalled value "NS_56")

Initial Conditions
Test Environment (as specified in TS 36.508 [7] subclause 4.1)					Normal
Test Frequencies (as specified in TS 36.508 [7] subclause 4.3.1)					Refer to F_ULin test parameters with following: 5 MHz CH BW: 1630 MHz (low range) 10 MHz CH BW: 1632.5 MHz (low range)
Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1)					5MHz, 10MHz
Test Parameters for NS_56 A-MPR
			Downlink Configuration		Uplink Configuration
Configuration ID	F_UL	Ch BW	Mod’n	RB allocation FDD	Mod’n	RB allocation FDD	RB_start FDD
1	1630	5MHz	N/A for A-MPR testing		QPSK	1	0
2	1630	5MHz			QPSK	25	0
3 (Notes 2,3)	1630	5MHz			16QAM	25	0
4	1632.5	10MHz			QPSK	1	0
5	1632.5	10MHz			QPSK	12	0
6	1632.5	10MHz			QPSK	50	0
7 (Notes 2,3)	1632.5	10MHz			16QAM	50	0
8	1632.5	10MHz			QPSK	1	6
9	1632.5	10MHz			QPSK	1	35
10	1632.5	10MHz			QPSK	1	40
11	1632.5	10MHz			QPSK	1	49
12	1632.5	10MHz			QPSK	15	35
13	1632.5	10MHz			QPSK	10	40
14 (Notes 2,3)	1632.5	10MHz			16QAM	10	40
Note 1: The Configuration ID will be used to map the applicable Test Configuration to the corresponding Test Requirement in subclause 6.2.4.5 as not all combinations are necessarily required based on the applicability of the UE. Note 2: Applies only for UE-Categories ≥2. Note 3: The 16QAM configurations shall not apply to UEs which support UL 64QAM.

Editor’s note: The following lines belong at the end of section 6.2.4.4.1. As new tables are added to this section, these lines should always follow the tables.

1. Connect the SS to the UE antenna connectors as shown in Figure TS 36.508 [7] Annex A, Figure A.3.

2. The parameter settings for the cell are set up according to TS 36.508 [7] clause 4.4.3.

3. Downlink signals are initially set up according to Annex C.0, C.1, and C.3.0, and uplink signals according to Annex H.1 and H.3.0.

4. The UL Reference Measurement channels are set according to the applicable table from Table 6.2.4.4.1-1 to Table 6.2.4.4.1-26.

5. Propagation conditions are set according to Annex B.0.

6. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.2.4.4.3.

6.2.4.4.2 Test procedure

1. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to the applicable table from Table 6.2.4.4.1-1 to Table 6.2.4.4.1-26. Since the UE has no payload data to send, the UE transmits uplink MAC padding bits on the UL RMC.

2. Send continuously uplink power control "up" commands in the uplink scheduling information to the UE until the UE transmits at P_UMAX level.

3. Measure the mean power of the UE in the channel bandwidth of the radio access mode. The period of measurement shall be at least the continuous duration one sub-frame (1ms). For TDD slots with transient periods are not under test.

6.2.4.4.3 Message contents

Message contents are according to TS 36.508 [7] subclause 4.6, with the following exceptions for each network signalled value.

6.2.4.4.3.1 Message contents exceptions (network signalled value "NS_03")

1. Information element additionalSpectrumEmission is set to NS_03. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.1-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_03"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	3 (NS_03)

6.2.4.4.3.2 Message contents exceptions (network signalled value "NS_04")

1. Information element additionalSpectrumEmission is set to NS_04. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.2-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_04"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	4 (NS_04)

6.2.4.4.3.3 Message contents exceptions (network signalled value "NS_05")

1. Information element additionalSpectrumEmission is set to NS_05. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.3-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_05"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	5 (NS_05)

6.2.4.4.3.4 Message contents exceptions (network signalled value "NS_06")

1. Information element additionalSpectrumEmission is set to NS_06. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.4-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_06"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	6 (NS_06)

6.2.4.4.3.5 Message contents exceptions (network signalled value "NS_07")

1. Information element additionalSpectrumEmission is set to NS_07. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.5-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_07"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	7 (NS_07)

6.2.4.4.3.6 Message contents exceptions (network signalled value "NS_08")

1. Information element additionalSpectrumEmission is set to NS_08. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.6-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_08"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	8 (NS_08)

6.2.4.4.3.7 Message contents exceptions (network signalled value "NS_09")

1. Information element additionalSpectrumEmission is set to NS_09. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.7-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_09"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	9 (NS_09)

6.2.4.4.3.8 Message contents exceptions (network signalled value "NS_10")

Void

6.2.4.4.3.9 Message contents exceptions (network signalled value "NS_11")

1. Information element additionalSpectrumEmission is set to NS_11. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.9-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_11"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	11 (NS_11)

6.2.4.4.3.10 Message contents exceptions (network signalled value "NS_12")

1. Information element additionalSpectrumEmission is set to NS_12. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.10-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_12"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	12 (NS_12)

6.2.4.4.3.11 Message contents exceptions (network signalled value "NS_13")

1. Information element additionalSpectrumEmission is set to NS_13. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.11-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_13"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	13 (NS_13)

6.2.4.4.3.12 Message contents exceptions (network signalled value "NS_14")

1. Information element additionalSpectrumEmission is set to NS_14. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.12-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_14"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	14 (NS_14)

6.2.4.4.3.13 Message contents exceptions (network signalled value "NS_15")

1. Information element additionalSpectrumEmission is set to NS_15. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.13-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_15"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	15 (NS_15)

6.2.4.4.3.14 Message contents exceptions (network signalled value "NS_16")

1. Information element additionalSpectrumEmission is set to NS_16. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.14-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_16"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	16 (NS_16)

6.2.4.4.3.15 Message contents exceptions (network signalled value "NS_17")

1. Information element additionalSpectrumEmission is set to NS_17. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.15-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_17"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	17 (NS_17)

6.2.4.4.3.16 Message contents exceptions (network signalled value "NS_18")

1. Information element additionalSpectrumEmission is set to NS_18. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.16-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_18"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	18 (NS_18)

6.2.4.4.3.17 Message contents exceptions (network signalled value "NS_19")

1. Information element additionalSpectrumEmission is set to NS_19. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.17-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_19"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	19 (NS_19)

6.2.4.4.3.18 Message contents exceptions (network signalled value "NS_20")

1. Information element additionalSpectrumEmission is set to NS_20. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.18-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_20"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	20 (NS_20)

6.2.4.4.3.19 Message contents exceptions (network signalled value "NS_21")

1. Information element additionalSpectrumEmission is set to NS_21. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.19-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_21"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	21 (NS_21)

6.2.4.4.3.20 Message contents exceptions (network signalled value "NS_22")

Table 6.2.4.4.3.20-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_22"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	22 (NS_22)

6.2.4.4.3.21 Message contents exceptions (network signalled value "NS_23")

Table 6.2.4.4.3.21-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_23"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	23 (NS_23)

6.2.4.4.3.22 Message contents exceptions (network signalled value "NS_24")

1. Information element additionalSpectrumEmission is set to NS_24. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.22-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_24"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	24 (NS_24)

6.2.4.4.3.23 Message contents exceptions (network signalled value "NS_25")

1. Information element additionalSpectrumEmission is set to NS_25. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.23-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_25"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	25 (NS_25)

6.2.4.4.3.24 Reserved

6.2.4.4.3.25 Message contents exceptions (network signalled value "NS_27")

1. Information element additionalSpectrumEmission is set to NS_27. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.1-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_27"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	27 (NS_27)

6.2.4.4.3.26 Message contents exceptions (network signalled value "NS_35")

1. Information element additionalSpectrumEmission is set to NS_35. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.26-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_35"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	32
additionalSpectrumEmission-v10l0	35 (NS_35)

6.2.4.4.3.27 Message contents exceptions (network signalled value "NS_36")

1. Information element additionalSpectrumEmission is set to NS_36. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.27-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_36"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	32
additionalSpectrumEmission-v10l0	36 (NS_36)

6.2.4.4.3.28 Message contents exceptions (network signalled value "NS_38")

1. Information element additionalSpectrumEmission is set to NS_38. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.28-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_38"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	32
additionalSpectrumEmission-v10l0	38 (NS_38)

6.2.4.4.3.29 Message contents exceptions (network signalled value "NS_39")

1. Information element additionalSpectrumEmission is set to NS_39. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.29-1: SystemInformationBlockType2: Additional spurious emissions test requirement for "NS_39"

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	32
additionalSpectrumEmission-v10l0	39 (NS_39)

6.2.4.4.3.30 Message contents exceptions (network signalled value "NS_45")

1. Information element additionalSpectrumEmission is set to NS_45. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.30-1: SystemInformationBlockType2: Additional spurious emissions requirement

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	45 (NS_45)

6.2.4.4.3.31 Message contents exceptions (network signalled value "NS_56")

1. Information element additionalSpectrumEmission is set to NS_56. This can be set in the SystemInformationblockType2 as part of the cell broadcast message. This exception indicates that the UE shall meet the additional spurious emission requirement for a specific deployment scenario.

Table 6.2.4.4.3.31-1: SystemInformationBlockType2: Additional spurious emissions requirement

Derivation Path: TS 36.508 [7] clause 4.4.3.3, Table 4.4.3.3-1
Information Element	Value/remark	Comment	Condition
additionalSpectrumEmission	56 (NS_56)

6.2.4.5 Test requirements

The maximum output power, derived in step 3 shall be within the range prescribed by the nominal maximum output power and tolerance in the applicable table from Table 6.2.4.5-1 to Table 6.2.4.5-29. The allowed A-MPR values specified in Table 6.2.4.3-1 are in addition to the allowed MPR requirements specified in clause 6.2.3. For the UE maximum output power modified by MPR and/or A-MPR, the power limits specified in Table 6.2.5.3-1 apply.

Table 6.2.4.5-1: UE Power Class test requirements (network signalled value "NS_03")
(for Bands 4, 10, 23, 35, 36, 66, and 70)

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	1	0	0	22	2.0	25.7	19.3
2	0	0	0	23	2.0	25.7	20.3
3	1	0	0	22	2.0	25.7	19.3
4	1	1	0	21	2.0	25.7	18.3
5	0	0	0	23	2.0	25.7	20.3
6	2	1	0	20	2.5	25.7	16.8
7	1	0	0	22	2.0	25.7	19.3
8	1	1	0	21	2.0	25.7	18.3
9	0	1	0	22	2.0	25.7	19.3
10	0	0	0	23	2.0	25.7	20.3
11	2	1	0	20	2.5	25.7	16.8
12	1	1	0	21	2.0	25.7	18.3
13	1	1	0	21	2.0	25.7	18.3
14	0	1	0	22	2.0	25.7	19.3
15	0	0	0	23	2.0	25.7	20.3
16	2	1	0	20	2.5	25.7	16.8
17	1	1	0	21	2.0	25.7	18.3
18	1	1	0	21	2.0	25.7	18.3
19	0	1	0	22	2.0	25.7	19.3
20	0	0	0	23	2.0	25.7	20.3
21	2	1	0	20	2.5	25.7	16.8
22	1	1	0	21	2.0	25.7	18.3
23	1	1	0	21	2.0	25.7	18.3
24	0	1	0	22	2.0	25.7	19.3
25	0	0	0	23	2.0	25.7	20.3
26	2	1	0	20	2.5	25.7	16.8
27	1	1	0	21	2.0	25.7	18.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4.5-2: UE Power Class test requirements (network signalled value "NS_03")
(for Bands 2 and 25)

Configuration ID	EUTRA band	Test Freq.	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	2, 25	Mid					23	+2.7 / -3.7
1	2, 25	Low, High					23	+2.7 / -5.7
2	2, 25	Mid					23	+2.7 / -2.7
2	2, 25	Low, High					23	+2.7 / -4.2
3	2, 25	Mid					23	+2.7 / -3.7
3	2, 25	Low, High					23	+2.7 / -5.7
4	2, 25	Mid					23	+2.7 / -4.7
4	2, 25	Low, High					23	+2.7 / -7.7
5	2, 25	Mid					23	+2.7 / -2.7
5	2, 25	Low, High					23	+2.7 / -4.2
6	2, 25	Mid					23	+2.7 / -6.2
6	2, 25	Low, High					23	+2.7 / -9.2
7	2, 25	Mid					23	+2.7 / -3.7
7	2, 25	Low, High					23	+2.7 / -5.7
8	2, 25	All					23	+2.7 / -4.7
9	2, 25	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -3.7
9	2, 25	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -5.7
10	2, 25	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -2.7
10	2, 25	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -4.2
11	2, 25	All					23	+2.7 / -6.2
12	2, 25	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -4.7
12	2, 25	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -7.7
13	2, 25	All					23	+2.7 / -4.7
14	2, 25	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -3.7
14	2, 25	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -5.7
15	2, 25	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -2.7
15	2, 25	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -4.2
16	2, 25	All					23	+2.7 / -6.2
17	2, 25	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -4.7
17	2, 25	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -7.7
18	2, 25	All					23	+2.7 / -4.7
19	2, 25	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -3.7
19	2, 25	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -5.7
20	2, 25	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -2.7
20	2, 25	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -4.2
21	2, 25	All					23	+2.7 / -6.2
22	2, 25	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -4.7
22	2, 25	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -7.7
23	2, 25	All					23	+2.7 / -4.7
24	2, 25	All					23	+2.7 / -3.7
25	2, 25	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -2.7
25	2, 25	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -4.2
26	2, 25	All					23	+2.7 / -6.2
27	2, 25	All					23	+2.7 / -4.7

Table 6.2.4.5-3: UE Power Class test requirements (network signalled value "NS_04")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	1	1	0	21	2.0	25.7	18.3
2 (RBstart=0; Low Range)	0	1	1.5	20.5	2.5	25.7	17.3
2 (RBstart=0; Mid, High Range)	0	1	0	22	2.0	25.7	19.3
2 (RBstart=17; Low, Mid Range)	0	1	0	22	2.0	25.7	19.3
2 (RBstart=17; High Range)	0	1	1.5	20.5	2.5	25.7	17.3
3 (RBstart=0; Low Range)	0	0	1.5	21.5	2.0	25.7	18.8
3 (RBstart=0; Mid, High Range)	0	0	0	23	2.0	25.7	20.3
3 (RBstart=19; Low, Mid Range)	0	0	0	23	2.0	25.7	20.3
3 (RBstart=19; High Range)	0	0	1.5	21.5	2.0	25.7	18.8
4	1	1	0	21	2.0	25.7	18.3
5 (RBstart=0; Low Range)	1	1	1.5	19.5	3.5	25.7	15.3
5 (RBstart=0; Mid, High Range)	1	1	0	21	2.0	25.7	18.3
5 (RBstart=17; Low, Mid Range)	1	1	0	21	2.0	25.7	18.3
5 (RBstart=17; High Range)	1	1	1.5	19.5	3.5	25.7	15.3
6 (Low Range)	0	3	1.5	18.5	4.0	25.7	13.8
6 (Mid, High Range)	0	3	0	20	2.5	25.7	16.8
7 (Low Range)	0	3	1.5	18.5	4.0	25.7	13.8
7 (Mid, High Range)	0	3	0	20	2.5	25.7	16.8
8	1	3	0	19	3.5	25.7	14.8
9	2	3	0	18	4.0	25.7	13.3
10	1	0	0	22	2.0	25.7	19.3
11	2	0	0	21	2.0	25.7	18.3
12	1	2	0	20	2.5	25.7	16.8
13 (Low, Mid Range)	0	3	0	20	2.5	25.7	16.8
13 (High Range)	0	3	1.5	18.5	4.0	25.7	13.8
14 (Low, Mid Range)	0	3	0	20	2.5	25.7	16.8
14 (High Range)	0	3	1.5	18.5	4.0	25.7	13.8
15 (Low Range)	0	3	1.5	18.5	4.0	25.7	13.8
15 (Mid, High Range)	0	3	0	20	2.5	25.7	16.8
16 (Low, Mid Range)	0	3	1.5	18.5	4.0	25.7	13.8
16 (High Range)	0	3	0	20	2.5	25.7	16.8
17	1	3	0	19	3.5	25.7	14.8
18	2	3	0	18	4.0	25.7	13.3
19	1	0	0	22	2.0	25.7	19.3
20	2	0	0	21	2.0	25.7	18.3
21	1	2	0	20	2.5	25.7	16.8
22	1	3	0	19	2.0	25.7	16.3
23 (Low, Mid Range)	0	3	0	20	2.5	25.7	16.8
23 (High Range)	0	3	1.5	18.5	4.0	25.7	13.8
24 (Low Range)	0	3	1.5	18.5	4.0	25.7	13.8
24 (Mid, High Range)	0	3	0	20	2.5	25.7	16.8
25 (Low Range)	0	3	1.5	18.5	4.0	25.7	13.8
25 (Mid, High Range)	0	3	0	20	2.5	25.7	16.8
26	1	3	0	19	3.5	25.7	14.8
27	2	3	0	18	4.0	25.7	13.3
28	1	0	0	22	2.0	25.7	19.3
29	2	0	0	21	2.0	25.7	18.3
30	1	2	0	20	2.5	25.7	16.8
31	1	3	0	19	3.5	25.7	14.8
32 (Low, Mid Range)	0	3	0	20	2.5	25.7	16.8
32 (High Range)	0	3	1.5	18.5	4.0	25.7	13.8
33	0	2	1.5	19.5	3.5	25.7	15.3
34	1	0	0	22	2.0	25.7	19.3
35	1	0	0	22	2.0	25.7	19.3
36	2	0	0	21	2.0	25.7	18.3
37	2	0	0	21	2.0	25.7	18.3
38	0	3	1.5	18.5	4.0	25.7	13.8
39	0	0	0	23	2.0	25.7	20.3
40	1	1	0	21	2.0	25.7	18.3
41	1	1	0	21	2.0	25.7	18.3
42 (Low Range)	1	2	0	20	2.5	25.7	16.8
42 (Mid, High Range, 2504.1 MHz)	1	0	0	22	2.0	25.7	19.3
43 (Low Range)	2	2	0	19	3.5	25.7	14.8
43 (Mid, High Range, 2504.1 MHz )	2	0	0	21	2.0	25.7	18.3
44	0	3	1.5	18.5	4.0	25.7	13.8
45	0	0	0	23	2.0	25.7	20.3
46	1	1	0	21	2.0	25.7	18.3
47	1	1	0	21	2.0	25.7	18.3
48 (Low Range)	1	3	0	19	3.5	25.7	14.8
48 (Mid, High Range, 2510.9 MHz)	1	0	0	22	2.0	25.7	19.3
49 (Low Range)	2	3	0	18	4.0	25.7	13.3
49 (Mid, High Range, 2510.9 MHz)	2	0	0	21	2.0	25.7	18.3
50	0	3	1.5	18.5	4.0	25.7	13.8
51	0	0	0	23	2.0	25.7	20.3
52	1	1	0	21	2.0	25.7	18.3
53	1	1	0	21	2.0	25.7	18.3
54 (Low Range)	1	3	0	19	3.5	25.7	14.8
54 (Mid, High Range, 2517.6 MHz)	1	0	0	22	2.0	25.7	19.3
55 (Low Range)	2	3	0	18	4.0	25.7	13.3
55 (Mid, High Range, 2517.6 MHz)	2	0	0	21	2.0	25.7	18.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4.5-4: UE Power Class test requirements (network signalled value "NS_05")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	0	0	0	23	2.0	25.7	20.3
2	0	0	0	23	2.0	25.7	20.3
3	1	0	0	22	2.0	25.7	19.3
4	0	0	0	23	2.0	25.7	20.3
5	0	0	0	23	2.0	25.7	20.3
6	0	0	0	23	2.0	25.7	20.3
7	0	0	0	23	2.0	25.7	20.3
8	1	0	0	22	2.0	25.7	19.3
9	1	0	0	22	2.0	25.7	19.3
10	1	1	0	21	2.0	25.7	18.3
11	2	1	0	20	2.5	25.7	16.8
12	0	0	0	23	2.0	25.7	20.3
13	0	0	0	23	2.0	25.7	20.3
14	0	0	0	23	2.0	25.7	20.3
15	0	0	0	23	2.0	25.7	20.3
16	1	0	0	22	2.0	25.7	19.3
17	1	0	0	22	2.0	25.7	19.3
18	0	0	0	23	2.0	25.7	20.3
19	0	0	0	23	2.0	25.7	20.3
20	0	0	0	23	2.0	25.7	20.3
21	0	0	0	23	2.0	25.7	20.3
22	1	0	0	22	2.0	25.7	19.3
23	1	0	0	22	2.0	25.7	19.3
24	0	0	0	23	2.0	25.7	20.3
25	0	0	0	23	2.0	25.7	20.3
26	0	0	0	23	2.0	25.7	20.3
27	0	0	0	23	2.0	25.7	20.3
28	1	0	0	22	2.0	25.7	19.3
29	1	0	0	22	2.0	25.7	19.3
30	1	1	0	21	2.0	25.7	18.3
31	2	1	0	20	2.5	25.7	16.8
32	0	0	0	23	2.0	25.7	20.3
33	0	0	0	23	2.0	25.7	20.3
34	0	0	0	23	2.0	25.7	20.3
35	0	0	0	23	2.0	25.7	20.3
36	1	0	0	22	2.0	25.7	19.3
37	1	0	0	22	2.0	25.7	19.3
38	1	1	0	21	2.0	25.7	18.3
39	2	1	0	20	2.5	25.7	16.8
40	1	1	0	21	2.0	25.7	18.3
41	2	1	0	20	2.5	25.7	16.8
42	0	11	0	12	6.0	25.7	5.3
43	1	11	0	11	6.0	25.7	4.3
44	0	0	0	23	2.0	25.7	20.3
45	1	0	0	22	2.0	25.7	19.3
46	1	3	0	19	3.5	25.7	14.8
47	1	5	0	17	5.0	25.7	11.3
48	0	5	0	18	4.0	25.7	13.3
49	0	5	0	18	4.0	25.7	13.3
50	0	1	0	22	2.0	25.7	19.3
51	0	11	0	12	6.0	25.7	5.3
52	1	11	0	11	6.0	25.7	4.3
53	0	0	0	23	2.0	25.7	20.3
54	1	0	0	22	2.0	25.7	19.3
55	1	3	0	19	3.5	25.7	14.8
56	1	5	0	17	5.0	25.7	11.3
57	1	10	0	12	6.0	25.7	5.3
58	0	5	0	18	4.0	25.7	13.3
59	0	5	0	18	4.0	25.7	13.3
60	1	1	0	21	2.0	25.7	18.3
61	1	0	0	22	2.0	25.7	19.3
62	2	0	0	21	2.0	25.7	18.3
63	0	0	0	23	2.0	25.7	20.3
64	0	0	0	23	2.0	25.7	20.3
65	0	0	0	23	2.0	25.7	20.3
66	0	0	0	23	2.0	25.7	20.3
67	1	0	0	22	2.0	25.7	19.3
68	1	0	0	22	2.0	25.7	19.3
69	1	0	0	22	2.0	25.7	19.3
70	2	0	0	21	2.0	25.7	18.3
71	0	0	0	23	2.0	25.7	20.3
72	0	0	0	23	2.0	25.7	20.3
73	0	0	0	23	2.0	25.7	20.3
74	0	0	0	23	2.0	25.7	20.3
75	1	0	0	22	2.0	25.7	19.3
76	1	0	0	22	2.0	25.7	19.3
77	1	1	0	21	2.0	25.7	18.3
78	2	1	0	20	2.5	25.7	16.8

Table 6.2.4.5-5: UE Power Class test requirements (network signalled value "NS_06")
(for Bands 13, 14, and 17)

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	13,14,17					23	+2.7 / -3.7
2	13,14,17					23	+2.7 / -2.7
3	13,14,17					23	+2.7 / -2.7
4	13,14,17					23	+2.7 / -3.7
5	13,14,17					23	+2.7 / -2.7
6	13,14,17					23	+2.7 / -3.7
7	13,14,17					23	+2.7 / -3.7
8	13,14,17					23	+2.7 / -2.7
9	13,14,17					23	+2.7 / -3.7

Table 6.2.4.5-6: UE Power Class test requirements (network signalled value "NS_06")
(for Band 12)

Configuration ID	EUTRA band	Test Freq.	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	12	Mid					23	+2.7 / -3.7
1	12	Low, High					23	+2.7 / -5.7
2	12	Mid					23	+2.7 / -2.7
2	12	Low, High					23	+2.7 / -4.2
3	12	Mid					23	+2.7 / -2.7
3	12	Low, High					23	+2.7 / -4.2
4	12	All					23	+2.7 / -3.7
5	12	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -2.7
5	12	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -4.2
6	12	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -3.7
6	12	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -5.7
7	12	All					23	+2.7 / -3.7
8	12	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -2.7
8	12	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -4.2
9	12	Low @ RB#(max+1-RB allocation), Mid, High @ RB#0					23	+2.7 / -3.7
9	12	Low @ RB#0, High @ RB#(max+1-RB allocation)					23	+2.7 / -5.7

Table 6.2.4.5-7: UE Power Class test requirements (network signalled value "NS_07")

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	13					23	+2.7 / -18.7
2	13					23	+2.7 / -13.7
3	13					23	+2.7 / -2.7
4	13					23	+2.7 / -19.7
5	13					23	+2.7 / -18.7
6	13					23	+2.7 / -20.7
7	13					23	+2.7 / -3.7
8	13					23	+2.7 / -2.7
9	13					23	+2.7 / -4.7
10	13					23	+2.7 / -12.7
11	13					23	+2.7 / -13.7
12	13					23	+2.7 / -2.7
13	13					23	+2.7 / -6.2
14	13					23	+2.7 / -19.7
15	13					23	+2.7 / -18.7
16	13					23	+2.7 / -20.7

Table 6.2.4.5-8: UE Power Class test requirements (network signalled value "NS_08")

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	19					23	+2.7 / -2.7
2	19					23	+2.7 / -2.7
3	19					23	+2.7 / -3.7
4	19					23	+2.7 / -2.7
5	19					23	+2.7 / -2.7
6	19					23	+2.7 / -3.7
7	19					23	+2.7 / -8.2
8	19					23	+2.7 / -9.7
9	19					23	+2.7 / -2.7
10	19					23	+2.7 / -2.7
11	19					23	+2.7 / -3.7
12	19					23	+2.7 / -8.2
13	19					23	+2.7 / -9.7

Table 6.2.4.5-9: UE Power Class test requirements (network signalled value "NS_09")

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	21					23	+2.7 / -2.7
2	21					23	+2.7 / -2.7
3	21					23	+2.7 / -3.7
4	21					23	+2.7 / -2.7
5	21					23	+2.7 / -2.7
6	21					23	+2.7 / -3.7
7	21					23	+2.7 / -4.7
8	21					23	+2.7 / -6.2
9	21					23	+2.7 / -2.7
19	21					23	+2.7 / -2.7
11	21					23	+2.7 / -3.7
12	21					23	+2.7 / -4.7
13	21					23	+2.7 / -6.2
14	21					23	+2.7 / -8.2

Table 6.2.4.5-10: UE Power Class test requirements (network signalled value "NS_10")

Void, not tested

Table 6.2.4.5-11: UE Power Class test requirements (network signalled value "NS_11 for Band 23")

Configuration ID	EUTRA Band	Centre Frequency	Class 3 (dBm)	Tol. (dB)
1a	23	2001.5 MHz	23	+ 2.7 / -11.7
1a	23	2001.5 MHz	23	+ 2.7 / -11.7
1b	23	2004.5 MHz	23	+ 2.7 / -4.7
1b	23	2004.5 MHz	23	+ 2.7 / -4.7
2a	23	2001.5 MHz	23	+ 2.7 / -11.7
2a	23	2001.5 MHz	23	+ 2.7 / -11.7
2b	23	2004.5 MHz	23	+ 2.7 / -4.7
2b	23	2004.5 MHz	23	+ 2.7 / -4.7
3a	23	2001.5 MHz	23	+ 2.7 / -12.7
3a	23	2001.5 MHz	23	+ 2.7 / -12.7
3b	23	2004.5 MHz	23	+ 2.7 / -6.2
3b	23	2004.5 MHz	23	+ 2.7 / -6.2
4a	23	2001.5 MHz	23	+ 2.7 / -12.7
4a	23	2001.5 MHz	23	+ 2.7 / -12.7
4b	23	2004.5 MHz	23	+ 2.7 / -6.2
4b	23	2004.5 MHz	23	+ 2.7 / -6.2
5a	23	2002.5 MHz	23	+ 2.7 / -12.7
5a	23	2002.5 MHz	23	+ 2.7 / -12.7
5b	23	2004.5 MHz	23	+ 2.7 / -8.2
5b	23	2004.5 MHz	23	+ 2.7 / -8.2
5c	23	2007.5 MHz	23	+ 2.7 / -2.7
5c	23	2007.5 MHz	23	+ 2.7 / -2.7
6a	23	2002.5 MHz	23	+ 2.7 / -12.7
6a	23	2002.5 MHz	23	+ 2.7 / -12.7
6b	23	2004.5 MHz	23	+ 2.7 / -2.7
6b	23	2004.5 MHz	23	+ 2.7 / -2.7
6c	23	2007.5 MHz	23	+ 2.7 / -3.7
6c	23	2007.5 MHz	23	+ 2.7 / -3.7
7a	23	2002.5 MHz	23	+ 2.7 / -13.7
7a	23	2002.5 MHz	23	+ 2.7 / -13.7
7b	23	2004.5 MHz	23	+ 2.7 / -9.7
7b	23	2004.5 MHz	23	+ 2.7 / -9.7
7c	23	2007.5 MHz	23	+ 2.7 / -4.7
7c	23	2007.5 MHz	23	+ 2.7 / -4.7
8a	23	2002.5 MHz	23	+ 2.7 / -13.7
8a	23	2002.5 MHz	23	+ 2.7 / -13.7
8b	23	2004.5 MHz	23	+ 2.7 / -3.7
8b	23	2004.5 MHz	23	+ 2.7 / -3.7
8c	23	2007.5 MHz	23	+ 2.7 / -4.7
8c	23	2007.5 MHz	23	+ 2.7 / -4.7
9a	23	2002.5 MHz	23	+ 2.7 / -14.7
9a	23	2002.5 MHz	23	+ 2.7 / -14.7
9b	23	2004.5 MHz	23	+ 2.7 / -11.7
9b	23	2004.5 MHz	23	+ 2.7 / -11.7
9c	23	2007.5 MHz	23	+ 2.7 / -6.2
9c	23	2007.5 MHz	23	+ 2.7 / -6.2
10a	23	2005 MHz	23	+ 2.7 / -17.7
10a	23	2005 MHz	23	+ 2.7 / -17.7
10b	23	2005.5 MHz	23	+ 2.7 / -17.7
10c	23	2015 MHz	23	+ 2.7 / -2.7
11a	23	2005 MHz	23	+ 2.7 / -17.7
11a	23	2005 MHz	23	+ 2.7 / -17.7
11b	23	2005.5 MHz	23	+ 2.7 / -17.7
11c	23	2015 MHz	23	+ 2.7 / -2.7
12a	23	2005 MHz	23	+ 2.7 / -18.7
12a	23	2005 MHz	23	+ 2.7 / -18.7
12b	23	2005.5 MHz	23	+ 2.7 / -18.7
12c	23	2015 MHz	23	+ 2.7 / -3.7
13a	23	2005 MHz	23	+ 2.7 / -18.7
13a	23	2005 MHz	23	+ 2.7 / -18.7
13b	23	2005.5 MHz	23	+ 2.7 / -18.7
13c	23	2015 MHz	23	+ 2.7 / -3.7
14a	23	2005 MHz	23	+ 2.7 / -20.7
14b	23	2005.5 MHz	23	+ 2.7 / -20.7
14c	23	2015 MHz	23	+ 2.7 / -4.7
15a	23	2007.5 MHz	23	+ 2.7 / -21.7
15b	23	2012.5 MHz	23	+ 2.7 / -16.7
16a	23	2007.5 MHz	23	+ 2.7 / -13.7
16b (Note 1)	23	2012.5 MHz	23	+ 2.7 / -13.2
16b (Note 2)	23	2012.5 MHz	23	+ 2.7 / -12.2
17a	23	2007.5 MHz	23	+ 2.7 / -3.7
17b	23	2012.5 MHz	23	+ 2.7 / -3.7
18a	23	2007.5 MHz	23	+ 2.7 / -12.7
18b	23	2012.5 MHz	23	+ 2.7 / -12.7
19a	23	2007.5 MHz	23	+ 2.7 / -16.7
19b	23	2012.5 MHz	23	+ 2.7 / -8.7
20a	23	2007.5 MHz	23	+ 2.7 / -13.7
20b (Note 1)	23	2012.5 MHz	23	+ 2.7 / -13.2
20b (Note 2)	23	2012.5 MHz	23	+ 2.7 / -13.2
21a	23	2007.5 MHz	23	+ 2.7 / -4.7
21b	23	2012.5 MHz	23	+ 2.7 / -3.7
22a	23	2007.5 MHz	23	+ 2.7 / -13.7
22b	23	2012.5 MHz	23	+ 2.7 / -13.7
23a	23	2007.5 MHz	23	+ 2.7 / -17.7
23b	23	2012.5 MHz	23	+ 2.7 / -9.7
24	23	2010 MHz	23	+ 2.7 / -20.7
25	23	2010 MHz	23	+ 2.7 / -2.7
26	23	2010 MHz	23	+ 2.7 / -13.7
27	23	2010 MHz	23	+ 2.7 / -16.7
28	23	2010 MHz	23	+ 2.7 / -3.7
29	23	2010 MHz	23	+ 2.7 / -14.7
30	23	2010 MHz	23	+ 2.7 / -17.7
30	23	2010 MHz	23	+ 2.7 / -17.7
Note 1: RB_start = RB# 0 Note 2: RB_start = RB# (max +1 – RB allocation)

Table 6.2.4.5-12: UE Power Class 3 test requirements (network signalled value "NS_12")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	0	3	1.5	18.5	4	25.7	13.8
2	1	4	1.5	16.5	5	25.7	10.8
3	0	0	1.5	21.5	2	25.7	18.8
4	0	3	1.5	18.5	4	25.7	13.8
5	2	4	1.5	15.5	5	25.7	9.8
6	0	4	1.5	17.5	5	25.7	11.8
7	1	3	1.5	17.5	5	25.7	11.8
8	0	0	1.5	21.5	2	25.7	18.8
9	1	3	1.5	17.5	5	25.7	11.8
10	2	4	1.5	15.5	5	25.7	9.8
11	0	4	1.5	17.5	5	25.7	11.8
12	1	3	1.5	17.5	5	25.7	11.8
13	0	0	1.5	21.5	2	25.7	18.8
14	1	3	0	19	3,5	25.7	14.8
15	2	3	0	18	4	25.7	13.3
16	1	4	1.5	16.5	5	25.7	10.8
17	1	0	0	22	2	25.7	19.3
18	2	2	0	19	2	25.7	16.3
19	1	4	0	18	4	25.7	13.3
20	1	0	0	22	2	25.7	19.3
21	2	3	0	18	4	25.7	13.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4.5-13: UE Power Class 3 test requirements (network signalled value "NS_13")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	1	0	0	22	2	25.7	19.3
2	1	0	0	22	2	25.7	19.3
3	0	3	0	20	2.5	25.7	16.8
4	1	2	0	20	2.5	25.7	16.8
5	1	0	0	22	2	25.7	19.3
6	1	0	0	22	2	25.7	19.3
7	2	2	0	19	3.5	25.7	14.8
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4.5-14: UE Power Class 3 test requirements (network signalled value "NS_14")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	0	3	0	20	2.5	25.7	16.8
2	1	0	0	22	2	25.7	19.3
3	1	1	0	21	2	25.7	18.3
4	1	0	0	22	2	25.7	19.3
5	2	1	0	20	2,5	25.7	16.8
6	0	3	0	20	2.5	25.7	16.8
7	1	0	0	22	2	25.7	19.3
8	1	1	0	21	2	25.7	18.3
9	1	0	0	22	2	25.7	19.3
10	2	1	0	20	2,5	25.7	16.8
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4.5-15: UE Power Class test requirements (network signalled value "NS_15")

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	26					23	+2.7 / -4.2
2	26					23	+2.7 / -12.2
3	26					23	+2.7 / -5.7
4	26					23	+2.7 / -12.2
5	26					23	+2.7 / -19.2
6	26					23	+2.7 / -3.7
7	26					23	+2.7 / -4.2
8	26					23	+2.7 / -11.7
9	26					23	+2.7 / -17.7
10	26					23	+2.7 / -3.7
11	26					23	+2.7 / -6.2
12	26					23	+2.7 / -17.2
13	26					23	+2.7 / -8.2
14	26					23	+2.7 / -2.7
15	26					23	+2.7 / -3.7
16	26					23	+2.7 / -12.7
17	26					23	+2.7 / -15.7
18	26					23	+2.7 / -17.7
19	26					23	+2.7 / 3.7-
20	26					23	+2.7 / -9.7
21	26					23	+2.7 / -3.7
22	26					23	+2.7 / -3.7
23	26					23	+2.7 / -11.7
24	26					23	+2.7 / -17.7
25	26					23	+2.7 / -3.7
26	26					23	+2.7 / -11.7

Table 6.2.4.5-16A: UE Power Class test requirements (network signalled value "NS_16") when lower channel edge is at 807 MHz

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	27					23	+2.7/-2.7
2	27					23	+2.7/-3.7
3	27					23	+2.7-4.7
4	27					23	+2.7/-2.7
5	27					23	+2.7 / -4.7
6	27					23	+2.7 / -6.2
7	27					23	+2.7 / -8.2
8	27					23	+2.7 / -9.7
9	27					23	+2.7 / -4.7
10	27					23	+2.7 / -6.2
11	27					23	+2.7 / -11.7
12	27					23	+2.7 / -8.2
13	27					23	+2.7 / -11.7
14	27					23	+2.7 / -12.7
15	27					23	+2.7 / -9.7
16	27					23	+2.7/-2.7
17	27					23	+2.7 / -8.2
18	27					23	+2.7 / -4.7
19	27					23	+2.7 / -8.2
20	27					23	+2.7 / -13.7
21	27					23	+2.7 / -13.7
22	27					23	+2.7 / -14.7
23	27					23	+2.7 / -13.7
24	27					23	+2.7 / -13.7

Table 6.2.4.5-16B: UE Power Class test requirements (network signalled value "NS_16") when lower channel edge is at 808.5 MHz

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	27					23	+2.7/-2.7
2	27					23	+2.7/-3.7
3	27					23	+2.7/-5.2
4	27					23	+2.7/-2.7
5	27					23	+2.7 / -3.7
6	27					23	+2.7 / -3.7
7	27					23	+2.7 / -4.7
8	27					23	+2.7 / -2.7
9	27					23	+2.7 / -3.7
10	27					23	+2.7 / -4.7
11	27					23	+2.7 / -6.2
12	27					23	+2.7 / -6.2
13	27					23	+2.7 / -8.2
14	27					23	+2.7 / -9.7
15	27					23	+2.7 / -9.7
16	27					23	+2.7/-2.7
17	27					23	+2.7 / -6.2
18	27					23	+2.7 / -4.7
19	27					23	+2.7 / -4.7
20	27					23	+2.7 / -9.7
21	27					23	+2.7 / -11.7
22	27					23	+2.7 / -12.7
23	27					23	+2.7 / -11.7
24	27					23	+2.7 / -11.7

Table 6.2.4.5-16C: UE Power Class test requirements (network signalled value "NS_16") when lower channel edge is at 812 MHz

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	27					23	+2.7/-2.7
2	27					23	+2.7/-3.7
3	27					23	+2.7/-4.7
4	27					23	+2.7/-2.7
5	27					23	+2.7 / -3.7
6	27					23	+2.7 / -3.7
7	27					23	+2.7 / -4.7
8	27					23	+2.7 / -2.7
9	27					23	+2.7 / -3.7
10	27					23	+2.7 / -3.7
11	27					23	+2.7 / -3.7
12	27					23	+2.7 / -3.7
13	27					23	+2.7 / -3.7
14	27					23	+2.7 / -4.7
15	27					23	+2.7 / -2.7
16						23	+2.7/-2.7
17	27					23	+2.7 / -3.7
18	27					23	+2.7 / -3.7
19	27					23	+2.7 / -3.7
20	27					23	+2.7 / -4.7
21	27					23	+2.7 / -8.2
22	27					23	+2.7 / -9.7
23	27					23	+2.7 / -6.2
24	27					23	+2.7 / -4.7

Table 6.2.4.5-17: UE Power Class test requirements (network signalled value "NS_17")

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	28					23	+2.7 / -3.2
2	28					23	+2.7 / -3.2
3	28					23	+2.7 / -4.2
4	28					23	+2.7 / -5.2
5	28					23	+2.7 / -3.2
6	28					23	+2.7 / -3.2
7	28					23	+2.7 / -4.2
8	28					23	+2.7 / -5.2

Table 6.2.4.5-18: UE Power Class test requirements (network signalled value "NS_18")

Configuration ID	EUTRA band	Class 1 (dBm)	Tol. (dB)	Class 2 (dBm)	Tol. (dB)	Class 3 (dBm)	Tol. (dB)
1	28					23	+2.7 / -3.2
2	28					23	+2.7 / -4.2
3	28					23	+2.7 / -5.2
4	28					23	+2.7 / -6.2
5	28					23	+2.7 / -7.2
6	28					23	+2.7 / -7.2
7	28					23	+ 2.7 / -8.7
8	28					23	+2.7 / -9.2
9	28					23	+2.7 / -7.2
10	28					23	+2.7 / -7.2
11	28					23	+2.7 / -8.7
12	28					23	+2.7 / -9.2
13	28					23	+2.7 / -7.2
14	28					23	+2.7 / -7.2
15	28					23	+2.7 / -8.7
16	28					23	+2.7 / -9.2

Table 6.2.4.5-19: UE Power Class test requirements (network signalled value "NS_19")

Configuration ID	Test Freq	RB location	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	Low	Full RB	1	0	1.5	20.5	2.5	25.7	17.3
2	Low	Full RB	2	0	1.5	19.5	3.5	25.7	15.3
3	Low	Low	1	1	0	21	2	25.7	18.3
3	Low	High	1	0	0	22	2	25.7	19.3
4	Low	Low	2	1	0	20	2.5	25.7	16.8
4	Low	High	2	0	0	21	2	25.7	18.3
5	Low	Low	0	2	1.5	19.5	3.5	25.7	15.3
5	Low	High	0	0	0	23	2	25.7	20.3
6	Low	Low	1	2	1.5	18.5	4	25.7	13.8
6	Low	High	1	0	0	22	2.5	25.7	18.8
7	Low	Low	1	3	0	19	3.5	25.7	14.8
7	Low	High	1	0	0	22	2	25.7	19.3
8	Low	Low	1	3	0	19	3.5	25.7	14.8
8	Low	High	1	0	0	22	2	25.7	19.3
9	Low	Low	2	3	0	18	4	25.7	13.3
9	Low	High	2	0	0	21	2	25.7	18.3
10	Low	Low	0	2	1.5	19.5	3.5	25.7	15.3
10	Low	High	0	0	0	23	2	25.7	20.3
11	Low	Low	1	2	0	20	2.5	25.7	16.8
11	Low	High	1	0	0	22	2	25.7	19.3
12	Low	Low	1	3	0	19	3.5	25.7	14.8
12	Low	High	1	0	0	22	2	25.7	19.3
13	Low	Low	1	3	0	19	3.5	25.7	14.8
13	Low	High	1	0	0	22	2	25.7	19.3
14	Low	Low	2	3	0	18	4	25.7	13.3
14	Low	High	2	0	0	21	2	25.7	18.3
Note 1: Lower limit is assuming ΔTIB,c is zero. If non-zero, PCMAX,c will decrease and T(PCMAX_L,c) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4.5-20: UE Power Class test requirements (network signalled value "NS_20 for Band 23")

Configuration ID	EUTRA Band	Centre Frequency	Class 3 (dBm)	Tol. (dB)
1a	23	2002.5 MHz	23	+ 2.7 / -24.7 (Note 1)
1a	23	2002.5 MHz	23	+ 2.7 / -24.7 (Note 1)
1b	23	2007.5 MHz	23	+ 2.7 / -2.7
1b	23	2007.5 MHz	23	+ 2.7 / -2.7
1c	23	2012.5 MHz	23	+ 2.7 / -2.7
1c	23	2012.5 MHz	23	+ 2.7 / -2.7
1d	23	2017.5 MHz	23	+ 2.7 / -2.7
1d	23	2017.5 MHz	23	+ 2.7 / -2.7
2a	23	2002.5 MHz	23	+ 2.7 / -23.7 (Note 1)
2a	23	2002.5 MHz	23	+ 2.7 / -23.7 (Note 1)
2b	23	2007.5 MHz	23	+ 2.7 / -7.7
2b	23	2007.5 MHz	23	+ 2.7 / -7.7
2c	23	2012.5 MHz	23	+ 2.7 / -7.7
2c	23	2012.5 MHz	23	+ 2.7 / -7.7
2d	23	2017.5 MHz	23	+ 2.7 / -3.7
2d	23	2017.5 MHz	23	+ 2.7 / -3.7
3a	23	2002.5 MHz	23	+ 2.7 / -23.7 (Note 1)
3a	23	2002.5 MHz	23	+ 2.7 / -23.7 (Note 1)
3b	23	2007.5 MHz	23	+ 2.7 / -11.7
3b	23	2007.5 MHz	23	+ 2.7 / -11.7
3c	23	2012.5 MHz	23	+ 2.7 / -11.7
3c	23	2012.5 MHz	23	+ 2.7 / -11.7
3d	23	2017.5 MHz	23	+ 2.7 / -3.7
3d	23	2017.5 MHz	23	+ 2.7 / -3.7
4a	23	2002.5 MHz	23	+ 2.7 / -23.7 (Note 1)
4a	23	2002.5 MHz	23	+ 2.7 / -23.7 (Note 1)
4b	23	2007.5 MHz	23	+ 2.7 / -7.7
4b	23	2007.5 MHz	23	+ 2.7 / -7.7
4c	23	2012.5 MHz	23	+ 2.7 / -7.7
4c	23	2012.5 MHz	23	+ 2.7 / -7.7
4d	23	2017.5 MHz	23	+ 2.7 / -3.7
4d	23	2017.5 MHz	23	+ 2.7 / -3.7
5a	23	2002.5 MHz	23	+ 2.7 / -23.7 (Note 1)
5a	23	2002.5 MHz	23	+ 2.7 / -23.7 (Note 1)
5b	23	2007.5 MHz	23	+ 2.7 / -11.7
5b	23	2007.5 MHz	23	+ 2.7 / -11.7
5c	23	2012.5 MHz	23	+ 2.7 / -11.7
5c	23	2012.5 MHz	23	+ 2.7 / -11.7
5d	23	2017.5 MHz	23	+ 2.7 / -3.7
5d	23	2017.5 MHz	23	+ 2.7 / -3.7
6a	23	2005 MHz	23	+ 2.7 / -21.7 (Note 1)
6a	23	2005 MHz	23	+ 2.7 / -21.7 (Note 1)
6b	23	2015 MHz	23	+ 2.7 / -2.7
6b	23	2015 MHz	23	+ 2.7 / -2.7
7a	23	2005 MHz	23	+ 2.7 / -7.7 (Note 1)
7a	23	2005 MHz	23	+ 2.7 / -7.7 (Note 1)
7b	23	2015 MHz	23	+ 2.7 / -2.7
7b	23	2015 MHz	23	+ 2.7 / -2.7
8a	23	2005 MHz	23	+ 2.7 / -11.7 (Note 1)
8b	23	2015 MHz	23	+ 2.7 / -8.7
9a	23	2005 MHz	23	+ 2.7 / -8.7 (Note 1)
9a	23	2005 MHz	23	+ 2.7 / -8.7 (Note 1)
9b	23	2015 MHz	23	+ 2.7 / -3.7
10a	23	2005 MHz	23	+ 2.7 / -11.7 (Note 1)
10b	23	2005 MHz	23	+ 2.7 / -8.7
10b	23	2005 MHz	23	+ 2.7 / -8.7
11	23	2012.5 MHz	23	+ 2.7 / -11.7
12	23	2012.5 MHz	23	+ 2.7 / -7.7
13	23	2012.5 MHz	23	+ 2.7 / -11.7
13	23	2012.5 MHz	23	+ 2.7 / -11.7
14	23	2012.5 MHz	23	+ 2.7 / -17.7
15	23	2012.5 MHz	23	+ 2.7 / -8.7
16	23	2012.5 MHz	23	+ 2.7 / -12.7
17	23	2012.5 MHz	23	+ 2.7 / -18.7
18	23	2010 MHz	23	+ 2.7 / -22.7
19	23	2010 MHz	23	+ 2.7 / -14.7
20	23	2010 MHz	23	+ 2.7 / -13.7 (Note 1)
21	23	2010 MHz	23	+ 2.7 / -8.7 (Note 1)
22	23	2010 MHz	23	+ 2.7 / -11.7 (Note 1)
23	23	2010 MHz	23	+ 2.7 / -15.7 (Note 1)
24	23	2010 MHz	23	+ 2.7 / -14.7 (Note 1)
25	23	2010 MHz	23	+ 2.7 / -19.7 (Note 1)
26	23	2010 MHz	23	+ 2.7 / -12.7 (Note 1)
Note 1: The output power within 2000-2005 MHz shall not be higher than 7.7 dBm

Table 6.2.4.5-21: UE Power Class 3 test requirements (network signalled value "NS_21 for Band 30")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	0	0	0	23	2.0	25.7	20.3
2	1	0	0	22	2.0	25.7	19.3
3	0	4	0	19	3.5	25.7	14.8
4	0	4	0	19	3.5	25.7	14.8
5	1	0	0	22	2.0	25.7	19.3
6	0	3	0	20	2.5	25.7	16.8
7	1	3	0	19	3.5	25.7	14.8
8	2	3	0	18	4.0	25.7	13.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4.5-22: UE Power Class Test requirements (network signalled value "NS_22")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	0	0	0	23	2.0	26	19
2	1	0	0	22	2.0	26	18
3	0	0	0	23	2.0	26	19
4	1	0	0	22	2.0	26	18
5	1	0	0	22	2.0	26	18
6	1	4	0	18	4.0	26	13
7	1	3	0	19	3.5	26	14.5
8	0	3	0	20	2.5	26	16
9	0	3	0	20	2.5	26	16
10	1	3	0	19	3.5	26	14.5
11	1	3	0	19	3.5	26	14.5
12	1	5	0	17	5.0	26	11
13	1	4	0	18	4.0	26	13
14	0	3	0	20	2.5	26	16
15	0	3	0	20	2.5	26	16
16	1	3	0	19	3.5	26	14.5
17	1	3	0	19	3.5	26	14.5
18	1	5	0	17	5.0	26	11
19	1	4	0	18	4.0	26	13
20	0	3	0	20	2.5	26	16
21	0	3	0	20	2.5	26	16
22	1	3	0	19	3.5	26	14.5
23	1	3	0	19	3.5	26	14.5
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4.5-23: UE Power Class Test requirements (network signalled value "NS_23")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	0	0	0	23	2.0	25.7	20.3
2	0	0	0	23	2.0	25.7	20.3
3	1	0	0	22	2.0	25.7	19.3
4	1	0	0	22	2.0	25.7	19.3
5	1	0	0	22	2.0	25.7	19.3
6	1	0	0	22	2.0	25.7	19.3
7	1	0	0	22	2.0	25.7	19.3
8	1	0	0	22	2.0	25.7	19.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4.5-24: UE Power Class 3 test requirements (network signalled value "NS_24")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	0	10	0	13	5.0	25.7	7.3
2	0	10	0	13	5.0	25.7	7.3
3	1	10	0	12	6.0	25.7	5.3
4	2	10	0	11	6.0	25.7	4.3
5	0	0	0	23	2.0	25.7	20.3
6	0	2	0	21	2.0	25.7	18.3
7	2	2	0	19	3.5	25.7	14.8
8	1	2	0	20	2.5	25.7	16.8
9	1	1	0	21	2.0	25.7	18.3
10	0	3	0	20	2.5	25.7	16.8
11	0	1	0	22	2.0	25.7	19.3
12	1	1	0	21	2.0	25.7	18.3
13	0	0	0	23	2.0	25.7	20.3
14	0	0	0	23	2.0	25.7	20.3
15	0	9	0	14	5.0	25.7	8.3
16	0	9	0	14	5.0	25.7	8.3
17	1	9	0	13	5.0	25.7	7.3
18	0	17	0	6	7.0	25.7	-1.7
19	1	17	0	5	7.0	25.7	-2.7
20	2	17	0	4	7.0	25.7	-3.7
21	0	2	0	21	2.0	25.7	18.3
22	0	2	0	21	2.0	25.7	18.3
23	1	2	0	20	2.5	25.7	16.8
24	2	8	0	13	5.0	25.7	7.3
25	0	0	0	23	2.0	25.7	20.3
26	0	7	0	16	5.0	25.7	10.3
27	1	7	0	15	5.0	25.7	9.3
28	0	0	0	23	2.0	25.7	20.3
29	0	17	0	6	7.0	25.7	-1.7
30	0	17	0	6	7.0	25.7	-1.7
31	1	17	0	5	7.0	25.7	-2.7
32	2	17	0	4	7.0	25.7	-3.7
33	0	17	0	6	7.0	25.7	-1.7
34	0	17	0	6	7.0	25.7	-1.7
35	1	17	0	5	7.0	25.7	-2.7
36	2	17	0	4	7.0	25.7	-3.7
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4.5-25: UE Power Class 3 test requirements (network signalled value "NS_25")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	1	5	0	17	5.0	25.7	11.3
2	2	5	0	16	5.0	25.7	10.3
3	0	0	0	23	2.0	25.7	20.3
4	0	2	0	21	2.0	25.7	18.3
5	0	2	0	21	2.0	25.7	18.3
6	1	2	0	20	2.5	25.7	16.8
7	0	2	0	21	2.0	25.7	18.3
8	2	2	0	19	3.5	25.7	14.8
9	1	2	0	20	2.5	25.7	16.8
10	1	1	0	21	2.0	25.7	18.3
11	0	3	0	20	2.5	25.7	16.8
12	0	1	0	22	2.0	25.7	19.3
13	0	1	0	22	2.0	25.7	19.3
14	1	1	0	21	2.0	25.7	18.3
15	1	5	0	17	5.0	25.7	11.3
16	2	1	0	20	2.5	25.7	16.8
17	1	5	0	17	5.0	25.7	11.3
18	1	1	0	21	2.0	25.7	18.3
19	2	1	0	20	2.5	25.7	16.8
20	0	0	0	23	2.0	25.7	20.3
21	0	10	0	13	5.0	25.7	7.3
22	0	10	0	13	5.0	25.7	7.3
23	1	10	0	12	6.0	25.7	5.3
24	2	10	0	11	6.0	25.7	4.3
25	1	7	0	15	5.0	25.7	9.3
26	2	7	0	14	5.0	25.7	8.3
27	1	11	0	11	6.0	25.7	4.3
28	2	11	0	10	6.0	25.7	3.3
29	0	0	0	23	2.0	25.7	20.3
30	0	4	0	19	3.5	25.7	14.8
31	1	4	0	18	4.0	25.7	13.3
32	1	3	0	19	3.5	25.7	14.8
33	2	1	0	20	2.5	25.7	16.8
34	0	1	0	22	2.0	25.7	19.3
35	0	1	0	22	2.0	25.7	19.3
36	0	0	0	23	2.0	25.7	20.3
37	0	13	0	10	6.0	25.7	3.3
38	0	13	0	10	6.0	25.7	3.3
39	1	13	0	9	6.0	25.7	2.3
40	2	13	0	8	6.0	25.7	1.3
41	0	11	0	12	6.0	25.7	5.3
42	0	11	0	12	6.0	25.7	5.3
43	2	11	0	10	6.0	25.7	3.3
44	1	11	0	11	6.0	25.7	4.3
45	0	13	0	10	6.0	25.7	3.3
46	2	13	0	8	6.0	25.7	1.3
47	0	0	0	23	2.0	25.7	20.3
48	0	13	0	10	6.0	25.7	3.3
49	0	13	0	10	6.0	25.7	3.3
50	1	13	0	9	6.0	25.7	2.3
51	2	13	0	8	6.0	25.7	1.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4.5-26: Reserved

Table 6.2.4.5-27: UE Power Class 3 test requirements (network signalled value "NS_27")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	MAX{T_L, T(P_{CMAX_L,c})} (dB)	Upper limit (dBm)	Lower limit (dBm)
1	0	0	0	23	3	26.0	19
2	0	0	0	23	3	26.0	19
3	1	0	0	22	3	26.0	18
4	2	0	0	21	3	26.0	17
5	0	0	0	23	3	26.0	19
6	0	0	0	23	3	26.0	19
7	1	0	0	22	3	26.0	18
8	2	0	0	21	3	26.0	17
9	0	4	0	19	3.5	26.0	14.5
10	0	0	0	23	3	26.0	19
11	0	0	0	23	3	26.0	19
12	0	4	0	19	3.5	26.0	14.5
13	0	0	0	23	3	26.0	19
14	0	0	0	23	3	26.0	19
15	1	2	0	20	3	26.0	16
16	2	2	0	19	3.5	26.0	14.5
17	0	4	0	19	3.5	26.0	14.5
18	0	1	0	22	3	26.0	18
19	0	0	0	23	3	26.0	19
20	1	0	0	22	3	26.0	18
21	0	4	0	19	3.5	26.0	14.5
22	0	1	0	22	3	26.0	18
23	0	0	0	23	3	26.0	19
24	1	0	0	22	3	26.0	18
25	1	3	0	19	3.5	26.0	14.5
26	2	3	0	18	4.0	26.0	13
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4.5-28: UE Power Class 3 test requirements (network signalled value "NS_35")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	0	0	0	23	2	25.7	18.8
2	0	0	0	23	2	25.7	18.8
3	0	0	0	23	2	25.7	18.8
4	0	0	0	23	2	25.7	18.8
5	0	0	0	23	2	25.7	18.8
6	0	0	0	23	2	25.7	18.8
7	0	0	0	23	2	25.7	18.8
8	0	0	0	23	2	25.7	18.8
9	0	0	0	23	2	25.7	18.8
10	0	0	0	23	2	25.7	18.8
11	0	0	0	23	2	25.7	18.8
12	0	0	0	23	2	25.7	18.8
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4.5-29: UE Power Class 3 test requirements (network signalled value "NS_36")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	0	2	0	21	2	25.7	18.3
2	1	4	0	18	4	25.7	13.3
3	1	1	0	21	2	25.7	18.3
4	1	3	0	19	3.5	25.7	14.8
5	1	0	0	22	2	25.7	19.3
6	2	0	0	21	2	25.7	18.3
7	1	0	0	22	2	25.7	19.3
8	2	0	0	21	2	25.7	18.3
9	1	10	0	12	6	25.7	5.3
10	0	10	0	13	5	25.7	7.3
11	1	8	0	14	5	25.7	8.3
12	1	6	0	16	5	25.7	10.3
13	0	6	0	17	5	25.7	11.3
14	0	0	0	23	2	25.7	20.3
15	1	0	0	22	2	25.7	19.3
16	2	0	0	21	2	25.7	18.3
17	1	10	0	12	6	25.7	5.3
18	1	9	0	13	5	25.7	7.3
19	1	7	0	15	5	25.7	9.3
20	0	6	0	17	5	25.7	11.3
21	0	0	0	23	2	25.7	20.3
22	1	0	0	22	2	25.7	19.3
23	2	0	0	21	2	25.7	18.3
24	1	0	0	22	2	25.7	19.3
25	2	0	0	21	2	25.7	18.3
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.

Table 6.2.4.5-30: UE Power Class 3 test requirements (network signalled value "NS_56")

Configuration ID	MPR (dB)	A-MPR (dB)	ΔT_C,c (dB)	P_CMAX,c (dBm)	T(P_{CMAX_L,c}) (dB)	Upper limit (dBm)	Lower limit (dBm)
1	0	8	0	15	5	25.7	9.3
2	1	2	0	20	2.5	25.7	16.8
3	2	2	0	19	3.5	25.7	14.8
4	0	7	0	16	5	25.7	10.3
5	0	5	0	18	4	25.7	13.3
6	1	7	0	15	5	25.7	9.3
7	2	7	0	14	5	25.7	8.3
8	0	5	0	18	4	25.7	13.3
9	0	4	0	19	3.5	25.7	14.8
10	0	5	0	18	4	25.7	13.3
11	0	5	0	18	4	25.7	13.3
12	1	2	0	20	2.5	25.7	16.3
13	0	3	0	20	2.5	25.7	16.3
14	1	3	0	19	3.5	25.7	14.8
Note 1: Lower limit is assuming Δ_TIB,c is zero. If non-zero, P_CMAX,c will decrease and T(P_{CMAX_L,c}) may be higher resulting in different test requirements according to Table 6.2.5.3-1.