6.2.3 Maximum Power Reduction (MPR)
36.521-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 1: Conformance testingRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification
Editor’s note:
– Requirement for Band 44 is not yet finalised due to square brackets in core specification TS 36.101 Table 6.2.2-1.
– Test requirements values in this section need to be reviewed in order to take into account notes in Table 6.2.5.3-2: ΔTIB,c regarding ΔTIB,c and asymmetric lower tolerances in table 6.2.2.3-1.
6.2.3.1 Test purpose
The number of RB identified in Table 6.2.3.3-1 is based on meeting the requirements for adjacent channel leakage ratio and the maximum power reduction (MPR) due to Cubic Metric (CM).
Simple scaling can be used to derive the requirement for other bandwidth based on the previously agreed value for 5MHz channel bandwidth.
6.2.3.2 Test applicability
The requirements of this test apply in test cases 6.6.2.3 Adjacent Channel Leakage power Ratio to all types of E-UTRA Power Class 3 UE release 8 and forward
NOTE: As a result TC 6.2.3 has not been included in the test case applicability table 4.1-1, TS 36.521-2. This does not preclude the test from being used for R&D or other purposes if deemed useful.
6.2.3.3 Minimum conformance requirements
For UE Power Class 3, the allowed Maximum Power Reduction (MPR) for the maximum output power in Table 6.2.2.3-1 due to higher order modulation and transmit bandwidth configuration (resource blocks) is specified in Table 6.2.3.3-1.
Table 6.2.3.3-1: Maximum Power Reduction (MPR) for Power Class 3
|
Modulation |
Channel bandwidth / Transmission bandwidth configuration [RB] |
MPR (dB) |
|||||
|
1.4 MHz |
3.0 MHz |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
||
|
QPSK |
> 5 |
> 4 |
> 8 |
> 12 |
> 16 |
> 18 |
≤ 1 |
|
16 QAM |
≤ 5 |
≤ 4 |
≤ 8 |
≤ 12 |
≤ 16 |
≤ 18 |
≤ 1 |
|
16 QAM |
> 5 |
> 4 |
> 8 |
> 12 |
> 16 |
> 18 |
≤ 2 |
For PRACH, PUCCH and SRS transmission, the allowed MPR is according to that specified for PUSCH QPSK modulation for the corresponding transmission bandwidth.
For each subframe, the MPR is evaluated per slot and given by the maximum value taken over the transmission(s) within the slot, the maximum MPR over the two slots is then applied for the entire subframe.
For the UE maximum output power modified by MPR, the power limits specified in subclause 6.2.5.3 apply.
The normative reference for this requirement is TS 36.101 clause 6.2.3.
6.2.3.4 Test description
6.2.3.4.1 Initial condition
Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.
The initial test configurations consist of environmental conditions, test frequencies, and channel bandwidths based on E-UTRA operating bands specified in table 5.4.2.1-1. All of these configurations shall be tested with applicable test parameters for each channel bandwidth, and are shown in table 6.2.3.4.1-1. The details of the uplink reference measurement channels (RMCs) are specified in Annexes A.2. Configurations of PDSCH and PDCCH before measurement are specified in Annex C.2.
Table 6.2.3.4.1-1: Test Configuration Table
|
Initial Conditions |
|||||
|
Test Environment as specified in TS 36.508 [7] subclause 4.1 |
Normal, TL/VL, TL/VH, TH/VL, TH/VH |
||||
|
Test Frequencies as specified in TS 36.508 [7] subclause 4.3.1 |
Low range, Mid range, High range |
||||
|
Test Channel Bandwidths as specified in TS 36.508 [7] subclause 4.3.1 |
Lowest, 5MHz, 10MHz, Highest |
||||
|
Test Parameters for Channel Bandwidths |
|||||
|
Downlink Configuration |
Uplink Configuration |
||||
|
Ch BW |
N/A for Maximum Power Reduction (MPR) test case |
Mod’n |
RB allocation |
||
|
FDD |
TDD |
||||
|
1.4MHz |
QPSK |
5 |
5 |
||
|
1.4MHz |
QPSK |
6 |
6 |
||
|
1.4MHz |
16QAM |
5 |
5 |
||
|
1.4MHz |
16QAM |
6 |
6 |
||
|
3.0MHz |
QPSK |
4 |
4 |
||
|
3.0MHz |
QPSK |
15 |
15 |
||
|
3.0MHz |
16QAM |
4 |
4 |
||
|
3.0MHz |
16QAM |
15 |
15 |
||
|
5MHz |
QPSK |
8 |
8 |
||
|
5MHz |
QPSK |
25 |
25 |
||
|
5MHz |
16QAM |
8 |
8 |
||
|
5MHz |
16QAM |
25 |
25 |
||
|
10MHz |
QPSK |
12 |
12 |
||
|
10MHz |
QPSK |
50 |
50 |
||
|
10MHz |
16QAM |
12 |
12 |
||
|
10MHz |
16QAM |
50 (Note 3) |
50 (Note 3) |
||
|
15MHz |
QPSK |
16 |
16 |
||
|
15MHz |
QPSK |
75 |
75 |
||
|
15MHz |
16QAM |
16 |
16 |
||
|
15MHz |
16QAM |
75 (Note 3) |
75 (Note 3) |
||
|
20MHz |
QPSK |
18 |
18 |
||
|
20MHz |
QPSK |
100 |
100 |
||
|
20MHz |
16QAM |
18 |
18 |
||
|
20MHz |
16QAM |
100 (Note 3) |
100 (Note 3) |
||
|
Note 1: Test Channel Bandwidths are checked separately for each E-UTRA band, the applicable channel bandwidths are specified in Table 5.4.2.1-1. Note 2: The RBstart of partial RB allocation shall be RB#0 and RB# (max + 1 – RB allocation) of the channel bandwidth. Note 3: Applies only for UE-Categories ≥2. |
|||||
1. Connect the SS and interfering sources to the UE antenna connectors as shown in TS 36.508 [7] Annex A Figure A.3.
2. The parameter settings for the cell are set up according to TS 36.508 [7] subclause 4.4.3.
3. Downlink signals are initially set up according to Annex C.0, C.1, and C.3.0, and uplink signals according to Annex H.1 and H.3.0.
4. The UL Reference Measurement channels are set according to Table 6.2.3.4.1-1.
5. Ensure the UE is in State 3A-RF according to TS 36.508 [7] clause 5.2A.2. Message contents are defined in clause 6.2.2.4.3.
6.2.3.4.2 Test procedure
1. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 for C_RNTI to schedule the UL RMC according to Table 6.2.3.4.1-1. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC
2. Send continuously uplink power control "up" commands in the uplink scheduling information to the UE to ensure that the UE transmits at PUMAX level.
3. Measure the mean power of the UE in the channel bandwidth of the radio access mode. The period of measurement shall be at least the continuous duration one sub-frame (1ms). For TDD slots with transient periods are not under test.
6.2.3.4.3 Message contents
Message contents are according to TS 36.508 [7] subclause 4.6.
6.2.3.5 Test requirements
The maximum output power, derived in step 2 shall be within the range prescribed by the nominal maximum output power and tolerance in Table 6.2.3.5-1.
Table 6.2.3.5-1: UE Power Class test requirements
|
E-UTRA Band |
Class 1 (dBm) |
Tol. (Db) |
Class 2 (dBm) |
Tol. (dB) |
Class 3 (dBm) |
QPSK partial RB allocation Tol. (dB)) |
QPSK full RB allocation Tol. (dB)) |
16QAM partial RB allocation Tol. (dB) |
16QAM full RB allocation Tol. (dB) |
|
1 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
2 |
23 |
±2.71 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -4.7 |
||||
|
3 |
23 |
±2.71 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -4.7 |
||||
|
4 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
5 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
6 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
7 |
23 |
±2.71 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -4.7 |
||||
|
8 |
23 |
±2.71 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -4.7 |
||||
|
9 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
10 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
11 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
12 |
23 |
±2.71 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -4.7 |
||||
|
13 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
14 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
… |
|||||||||
|
17 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
18 |
23 |
±2.73 |
+2.7 / 3 -3.7 |
+2.7 / 3 -3.7 |
+2.7 / 3 -4.7 |
||||
|
19 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
20 |
23 |
±2.71 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -4.7 |
||||
|
21 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
22 |
23 |
+3.0/-4.5 |
+3.0/-5.5 |
+3.0/-5.5 |
+3.0/-6.5 |
||||
|
23 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
24 |
23 |
±2.7 |
+2.7 / 1,2 -4.7 |
+2.7 / 1,2 -4.7 |
+2.7 / 1,2 -5.7 |
||||
|
25 |
23 |
±2.71 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -4.7 |
||||
|
26 |
23 |
±2.71 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -4.7 |
||||
|
27 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
28 |
23 |
+2.7/-3.2 |
+2.7/-4.2 |
+2.7/-4.2 |
+2.7/-5.2 |
||||
|
30 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
31 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
… |
|||||||||
|
33 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
34 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
35 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
36 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
37 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
38 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
39 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
40 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
41 |
23 |
±2.71 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -4.7 |
||||
|
42 |
23 |
+3.0 / -4.0 |
+3.0 / -5.0 |
+3.0 / -5.0 |
+3.0 / -6.0 |
||||
|
43 |
23 |
+3.0 / -4.0 |
+3.0 / -5.0 |
+3.0 / -5.0 |
+3.0 / -6.0 |
||||
|
44 |
23 |
+2.7/ [-3.7] |
+2.7 / [-4.7] |
+2.7 / [-4.7] |
+2.7 / [-5.7] |
||||
|
45 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
… |
|||||||||
|
65 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
66 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
… |
|||||||||
|
68 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
… |
|||||||||
|
70 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
72 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
… |
|||||||||
|
74 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
85 |
23 |
±2.71 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -3.7 |
+2.7 / 1,2 -4.7 |
||||
|
87 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
88 |
23 |
±2.7 |
+2.7 / -3.7 |
+2.7 / -3.7 |
+2.7 / -4.7 |
||||
|
Note 1: For transmission bandwidths (Figure 5.4.2-1) confined within FUL_low and FUL_low + 4 MHz or FUL_high – 4 MHz and FUL_high, the maximum output power requirement is relaxed by reducing the lower tolerance limit by 1.5 dB. Note 2: For the UE maximum output power modified by MPR, the power limits specified in Table 6.2.5.3-1 apply Note 3: For a UE that supports both Band 18 and Band 26, the maximum output power requirement is relaxed by reducing the lower tolerance limit by 1.5dB for transmission bandwidths confined within 815 MHz and 818 MHz |
|||||||||