42.4.3 Macros and Default Message contents
3GPP51.010-1Mobile Station (MS) conformance specificationPart 1: Conformance specificationTS
42.4.3.1 Macros
In order to simplify the process of writing and coding test cases, macros are referenced in the expected signalling tables. These macros provide all additional signalling needed to complete the particular test but are not relevant to its purpose.
42.4.3.1.1 Void
42.4.3.1.2 Void
42.4.3.2 Default Messages
42.4.3.2.1 PACKET CELL CHANGE ORDER message
MESSAGE_TYPE |
0000 01 |
PAGE_MODE |
00 Normal Paging |
Referenced Address |
|
– |
10 (address is TLLI) |
– TLLI |
same as the value received from MS |
IMMEDIATE_REL |
1 (Immediate release of the on-going TBF.) |
ARFCN |
For GSM 900: 00 0001 0100 (ARFCN 20) For DCS 1 800 and PCS 1 900: 10 0100 1110 (ARFCN 590) For GSM 700, T-GSM 810: 01 1100 1001 (ARFCN 457) For GSM 850: 00 1001 0011 (ARFCN 147) |
BSIC |
For GSM 700, T-GSM 810, GSM 850 and GSM 900: 001101 For DCS 1 800 and PCS 1 900: 001101 |
NC Measurement Parameters |
|
NETWORK_CONTROL_ORDER |
0 0 NC0 |
{ 0 | 1 < NC_NON_DRX_PERIOD < NC_REPORTING_PERIOD_I < NC_REPORTING_PERIOD_T } |
0 No additional NC parameters |
NC Frequency list struct |
|
{ 0 | 1 < NC_FREQUENCY_LIST } |
0 No NC_FREQUENCY_LIST |
< padding bits > |
Spare Padding |
42.4.3.2.2 PACKET CELL CHANGE FAILURE message
MESSAGE_TYPE |
0000 00 |
TLLI |
same as the value received from MS |
ARFCN |
For GSM 900: 00 0001 0100 (ARFCN 20) For DCS 1 800 and PCS 1 900: 10 0100 1110 (ARFCN 590) For GSM 700, T-GSM 810: 01 1100 1001 (ARFCN 457) For GSM 850: 00 1001 0011 (ARFCN 147) |
BSIC |
For GSM 700, T-GSM 810, GSM 850 and GSM 900: 001101 For DCS 1 800 and PCS 1 900: 001101 |
CAUSE |
0 0 0 1 No response on target cell |
spare padding |
Spare Padding |
42.4.3.2.3 PACKET MEASUREMENT ORDER message
MESSAGE_TYPE |
0000 11 |
PAGE_MODE |
00 Normal Paging |
TLLI |
10 (address is TLLI) |
– |
Same as the value received from MS |
PMO_INDEX |
0 0 0 first message |
PMO_COUNT |
0 0 0 one message expected |
{ 0 | 1 < NC Measurement Parameters } |
1 NC Measurement Parameters available |
NC Measurement Parameters |
|
NETWORK_CONTROL_ORDER |
0 1 NC1 |
{ 0 | 1 < NC_NON_DRX_PERIOD < NC_REPORTING_PERIOD_I < NC_REPORTING_PERIOD_T } |
1 Additional NC parameters available NC_NON_DRX_PERIOD = 000 (No non-DRX mode after a measurement report has been sent) NC_REPORTING_PERIOD_I = 111 (61.44 sec) NC_REPORTING_PERIOD_T = 011 (3.84 sec) |
{ 0 | 1 < NC_FREQUENCY_LIST } |
0 No NC Frequency list struct available |
< padding bits > |
Spare Padding |