13.17.4a Output RF spectrum in EGPRS2A configuration

3GPP51.010-1Mobile Station (MS) conformance specificationPart 1: Conformance specificationTS

13.17.4a.1 Definition

The output RF spectrum is the relationship between the frequency offset from the carrier and the power, measured in a specified bandwidth and time, produced by the MS due to the effects of modulation and power ramping.

Since the conformance requirement, test procedure and test requirement of GSMK modulated signal’s output RF spectrum are defined in subclause 13.16.3 for GPRS MS, being thereby defined also for all EGPRS MS in that section and the conformance requirement, test procedure and test requirement of 8-PSK modulated signal’s output RF spectrum in EGPRS configuration subclause 13.17.4, only 16-QAM modulated signal’s RF output spectrum conformance requirement, test procedure and test requirements are defined in this subclause.13.17.4a.2 Conformance requirement

1. The level of the output RF spectrum due to 16-QAM modulation shall be no more than that given in 3GPP TS 45.005, subclause 4.2.1, with the following lowest measurement limits:

– -36 dBm below 600 kHz offset from the carrier;

– -51 dBm for GSM 400, GSM 700, GSM 850 and GSM 900 or -56 dBm for DCS 1 800 and PCS 1 900 from 600 kHz out to less than 1 800 kHz offset from the carrier;

– -46 dBm for GSM 400, GSM 700, GSM 850 and GSM 900 or -51 dBm for DCS 1 800 and PCS 1 900 at and beyond 1 800 kHz offset from the carrier;

but with the following exceptions at up to -36 dBm:

– up to three bands of 200 kHz width centred on a frequency which is an integer multiple of 200 kHz in the combined range 600 kHz to 6 000 kHz above and below the carrier;

– up to 12 bands of 200 kHz width centred on a frequency which is an integer multiple of 200 kHz at more than 6 000 kHz offset from the carrier.

1.1 Under normal conditions; 3GPP TS 45.005, subclause 4.2.1.

1.2 Under extreme conditions; 3GPP TS 45.005, subclause 4.2.1; 3GPP TS 45.005, annex D subclauses D.2.1 and D.2.2.

2. The level of the output RF spectrum due to switching transients shall be no more than given in 3GPP TS 45.005, subclause 4.2.2, table "a) Mobile Station".

2.1 Under normal conditions; 3GPP TS 45.005, subclause 4.2.2.

2.2 Under extreme conditions; 3GPP TS 45.005, subclause 4.2.2; 3GPP TS 45.005 annex D subclauses D.2.1 and D.2.2.

3. When allocated a channel, the power emitted by the GSM 400, GSM 900 and DCS 1800 MS, in the band 935 MHz to 960 MHz shall be no more than -79 dBm, in the band 925 MHz to 935 MHz shall be no more than ‑67 dBm and in the band 1 805 MHz to 1 880 MHz shall be no more than -71 dBm, except in five measurements in each of the bands 925 MHz to 960 MHz and 1 805 MHz to 1 880 MHz, where exceptions at up to -36 dBm are permitted. For GSM 400 mobiles, in addition, a limit of -67 dBm shall apply in the frequency bands 460,4 MHz to 467,6 MHz and 488,8 MHz to 496 MHz.

For GSM 700, GSM 850 and PCS 1 900, the power emitted by MS, in the band of 728 MHz to 736 MHz shall be no more than -73 dBm, in the band of 736 MHz to 746 MHz shall be no more than -79 dBm, in the band of 747 MHz to 757 MHz shall be no more than -79 dBm, in the band of 757 MHz to 763 MHz shall be no more than -73 dBm, in the band 869 MHz to 894 MHz shall be no more than -79 dBm, in the band 1 930 MHz to 1 990 MHz shall be no more than -71 dBm except in five measurements in each of the bands 728 MHz to 746 MHz, 747 MHz to 763 MHz, 869 MHz to 894 MHz and 1 930 MHz to 1 990 MHz where exceptions at up to -36 dBm are permitted; 3GPP TS 45.005, subclause 4.3.3.

13.17.4a.3 Test purpose

1. To verify that the output RF spectrum due to 16-QAM modulation of an EGPRS MS does not exceed conformance requirement 1.

1.1 Under normal conditions.

1.2 Under extreme conditions.

2. To verify that the output RF spectrum due to 16-QAM modulation of an EGPRS MS does not exceed conformance requirement 1 in 16-QAM uplink multislot configuration.

2.1 Under normal conditions.

2.2 Under extreme conditions.

3. To verify that the output RF spectrum due to switching transients of 16-QAM modulated signals of an EGPRS MS does not exceed conformance requirement 2 when a reasonable margin is allowed for the effect of spectrum due to modulation.

3.1 Under normal conditions.

3.2 Under extreme conditions.

4. To verify that the output RF spectrum due to switching transients of 16-QAM modulated signals of an EGPRS MS does not exceed conformance requirement 2 in 16-QAM uplink multislot configuration when a reasonable margin is allowed for the effect of spectrum due to modulation.

4.1 Under normal conditions.

4.2 Under extreme conditions.

5. To verify that the MS spurious emissions in the MS receive band for 16-QAM modulated signals of an EGPRS MS do not exceed conformance requirement 3.

6. To verify that the MS spurious emissions in the MS receive band for 16-QAM modulated signals of an EGPRS MS do not exceed conformance requirement 3 in 16-QAM uplink multislot configuration.

NOTE: For EGPRS MS capable of 16-QAM multislot configuration in the uplink, the tests are executed only for multislot configuration.

13.17.4a.4 Method of test

Initial conditions

The test shall be run under the default EGPRS conditions defined in clause 50, with power control parameter ALPHA (α) set to 0.

The Test Mode defined in 3GPP TS 44.014 subclause 5.4 shall be utilised. If the MS is capable of both:

Mode (a) transmitting pseudo-random data sequence in RLC data blocks;

Mode (b) transmitting looped-back RLC data blocks;

then Mode (a) will be used.

The SS commands the MS to transmit with its maximum number of uplink slots, with 16-QAM modulation in hopping mode. The hopping pattern includes only three channels, namely one with an ARFCN in the Low ARFCN range, a second one with an ARFCN in the Mid ARFCN range and the third one with an ARFCN in the High ARFCN range.

The SS shall use a transmission level of 23 dBVemf(  ).

NOTE 1: Although the measurement is made whilst the MS is in hopping mode, each measurement is on one single channel.

NOTE 2: This test is specified in hopping mode as a simple means of making the MS change channel, it would be sufficient to test in non hopping mode and to cell re-select the MS between the three channels tested at the appropriate time.

NOTE 3: Mid ARFCN range for GSM 900 will use the range 63-65 ARFCN

13.17.4a.4.2 Test procedure

NOTE: When averaging is in use during frequency hopping mode, the averaging only includes bursts transmitted when the hopping carrier corresponds to the nominal carrier of the measurement.

a) In steps b) to h) the FT is equal to the hop pattern ARFCN in the Mid ARFCN range.

b) The other settings of the spectrum analyser are set as follows:

– Zero frequency scan;

– Resolution bandwidth: 30 kHz;

– Video bandwidth: 30 kHz;

– Video averaging: may be used, depending on the implementation of the test.

The video signal of the spectrum analyser is "gated" such that the spectrum generated by at least 40 of the symbols 87 to 132 of the burst in one of the active time slots is the only spectrum measured. This gating may be analogue or numerical, dependent upon the design of the spectrum analyser. Only measurements during transmitted bursts on the nominal carrier of the measurement are included. The spectrum analyser averages over the gated period and over 200 or 50 such bursts, using numerical and/or video averaging.

The MS is commanded to its maximum power control level in every transmitted time slot.

c) By tuning the spectrum analyser centre frequency to the measurement frequencies the power level is measured over 50 bursts at all multiples of 30 kHz offset from FT to < 1 800 kHz.

d) The resolution and video bandwidth on the spectrum analyser are adjusted to 100 kHz and the measurements are made at the following frequencies:

on every ARFCN from 1 800 kHz offset from the carrier to the edge of the relevant transmit band for each measurement over 50 bursts.

at 200 kHz intervals over the 2 MHz either side of the relevant transmit band for each measurement over 50 bursts.

For GSM 400 and DCS 1 800:

at 200 kHz intervals over the band 450 MHz to 496 MHz for each measurement over 50 bursts.

at 200 kHz intervals over the band 925 MHz to 960 MHz for each measurement over 50 bursts.

at 200 kHz intervals over the band 1 805 MHz to 1 880 MHz for each measurement over 50 bursts.

For GSM 900

at 200 kHz intervals over the band 925 MHz to 960MHz for each measurement over 50 bursts;

at 200 kHz intervals over the band 1805 MHz to 1880 MHz for each measurement over 50 bursts.

For GSM 700, GSM 850 and DCS 1 900:

at 200 kHz intervals over the band 728MHz to 746 MHz for each measurement over 50 bursts.

at 200 kHz intervals over the band 747 MHz to 763 MHz for each measurement over 50 bursts.

at 200 kHz intervals over the band 869 MHz to 894 MHz for each measurement over 50 bursts.

at 200 kHz intervals over the band 1 930 MHz to 1 990 MHz for each measurement over 50 bursts.

e) The MS is commanded to its minimum power control level. The spectrum analyser is set again as in b).

f) By tuning the spectrum analyser centre frequency to the measurement frequencies the power level is measured over 200 bursts at the following frequencies:

FT;

FT + 100 kHz FT – 100 kHz;

FT + 200 kHz FT – 200 kHz;

FT + 250 kHz FT – 250 kHz;

FT + 200 kHz * N FT – 200 kHz * N;

where N = 2, 3, 4, 5, 6, 7, and 8;

and FT = RF channel nominal centre frequency.

g) Steps a) to f) is repeated except that in step a) the spectrum analyzer is gated so that the burst of the next active time slot is measured.

h) The spectrum analyser settings are adjusted to:

– Zero frequency scan;

– Resolution bandwidth: 30 kHz;

– Video bandwidth: 100 kHz;

– Peak hold.

The spectrum analyser gating of the signal is switched off.

The MS is commanded to its maximum power control level in every transmitted time slot.

i) By tuning the spectrum analyser centre frequency to the measurement frequencies the power level is measured at the following frequencies:

FT + 400 kHz FT – 400 kHz;

FT + 600 kHz FT – 600 kHz;

FT + 1,2 MHz FT – 1,2 MHz;

FT + 1,8 MHz FT – 1,8 MHz;

where FT = RF channel nominal centre frequency.

The duration of each measurement (at each frequency) will be such as to cover at least 10 burst transmissions at FT.

j) Step i) is repeated for power control levels 7 and 11.

k) Steps b), f), h) and i) are repeated with FT equal to the hop pattern ARFCN in the Low ARFCN range except that in step h) the MS is commanded to power control level 11 rather than maximum power.

l) Steps b), f), h) and i) are repeated with FT equal to the hop pattern ARFCN in the High ARFCN range except that in step h) the MS is commanded to power control level 11 rather than maximum power.

m) Steps a) b) f) h), and i) are repeated under extreme test conditions (annex 1, TC2.2). except that at step h) the MS is commanded to power control level 11.

13.17.4a.5 Test requirements

For absolute measurements, performed on a temporary antenna connector, in the frequency band 450 MHz to 486 MHz or 777 MHz to 792 MHz or 824 MHz to 849 MHz or 880 MHz to 915 MHz or 1 710 MHz to 1 785 MHz or 1 850 MHz to 1 910 MHz, the temporary antenna connector coupling factor, determined according to subclause 13.3.4.2.2 and annex 1 GC7, for the nearest relevant frequency, will be used.

For absolute measurements, performed on a temporary antenna connector, in the frequency band 450 MHz to 486 MHz or 925 MHz to 960 MHz, the temporary antenna connector coupling factor, will be as determined according to annex 1 GC7 for GSM 400 or GSM 900 MS respectively. For a DCS 1 800 MS and PCS 1 900 MS 0 dB will be assumed.

For absolute measurements, performed on a temporary antenna connector, in the frequency band 1 805 MHz to 1 880 MHz, the temporary antenna connector coupling factor, will be as determined according to annex 1 GC7 for DCS 1 800 MS. For GSM 400 MS and GSM 900 MS 0 dB will be assumed.

For absolute measurements, performed on a temporary antenna connector, in the frequency band 728 MHz to 763 MHz, the temporary antenna connector coupling factor, will be as determined according to annex 1 GC7 for GSM 700 MS. For a GSM 400, GSM 850, GSM 900, DCS 1800 or PCS 1 900 MS 0 dB will be assumed.

For absolute measurements, performed on a temporary antenna connector, in the frequency band 869 to 894 MHz, the temporary antenna connector coupling factor, will be as determined according to annex 1 GC7 for GSM 850 MS. For a GSM 400, GSM 700, GSM 900, DCS 1800 or PCS 1 900 MS 0 dB will be assumed.

The figures in the tables below, at the listed frequencies from the carrier (kHz), are the maximum level (dB) relative to a measurement in 30 kHz bandwidth on the carrier (reference 3GPP TS 45.005 subclause 4.2.1).

a) For the modulation sidebands out to less than 1 800 kHz offset from the carrier frequency (FT) measured in step c), f), i), k), l) and m) the measured power level in dB relative to the power level measured at FT, for all types of MS, shall not exceed the limits derived from the values shown in table 13.17.4a-1 for GSM 400, GSM 700, GSM 850 and GSM 900 or table 13.17.4a-2 for DCS 1800 or 13.17.4a-3 for PCS 1900 MS, according to the actual transmit power and frequency offset from FT. However any failures in the combined range 600 kHz to less than 1 800 kHz above and below the carrier may be counted towards the exceptions allowed in test requirements c) below where.

Case 1: Normal symbol rate using linearised GMSK pulse-shaping filter and higher symbol rate using spectrally narrow pulse shaping filter

Case 2: Higher symbol rate using spectrally wide pulse shaping filter

Table 13.17.4a-1: GSM 400, GSM 700, GSM 850 and GSM 900 Spectrum
due to modulation out to less than 1 800 kHz offset

Power level

power levels in dB relative to the

measurement at FT

Frequency offset (kHz)

(dBm)

100

200

250

400

 600

< 1 800

Case 1

 39

+0,5

‑30

‑33

‑60

‑66

37

+0,5

‑30

‑33

‑60

‑64

35

+0,5

‑30

‑33

‑60

‑62

 33

+0,5

‑30

‑33

‑60*

‑60

Power

[100]

[200]

[250]

[400]

[600]

level

Case 2

 39

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

37

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

35

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

 33

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

The values above are subject to the minimum absolute levels (dBm) below.

-36

-36

-36

-36

-36

-51

NOTE: * For equipment supporting QPSK, 8-PSK, 16-QAM or 32-QAM, the requirement for these modulations is ‑54 dB.

NOTE: ** The requirement shall be [tbd] when the wideband pulse shaping filter with the tight spectrum mask is indicated (see Pulse Format Information Element in 3GPP TS 44.060).

NOTE: *** the requirement shall be [tbd] when the wide pulse shaping filter with the tight spectrum mask is indicated (see Pulse Format Information Element in 3GPP TS 44.060).

Table 13.17.4a-2: DCS 1800 Spectrum due to modulation out to less than 1 800 kHz offset

Power level

power levels in dB relative to the

measurement at FT

Frequency offset (kHz)

(dBm)

100

200

250

400

 600

< 1 800

Case 1

 36

+0,5

‑30

‑33

‑60

‑60

34

+0,5

‑30

‑33

‑60

‑60

32

+0,5

‑30

‑33

‑60

‑60

30

+0,5

‑30

‑33

‑60*

‑60

28

+0,5

‑30

‑33

‑60*

‑60

26

+0,5

‑30

‑33

‑60*

‑60

 24

+0,5

‑30

‑33

‑60*

‑60

Power

[100]

[200]

[250]

[400]

[600]

Level

Case 2

 36

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

34

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

32

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

30

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

28

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

26

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

 24

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

The values above are subject to the minimum absolute levels (dBm) below.

-36

-36

-36

-36

-56

NOTE: * For equipment supporting QPSK, 8-PSK, 16-QAM or 32-QAM, the requirement for these modulations is ‑54 dB.

NOTE: ** The requirement shall be [tbd] when the wideband pulse shaping filter with the tight spectrum mask is indicated (see Pulse Format Information Element in 3GPP TS 44.060).

NOTE: *** the requirement shall be [tbd] when the wide pulse shaping filter with the tight spectrum mask is indicated (see Pulse Format Information Element in 3GPP TS 44.060).

Table 13.17.4a-3: PCS 1900 Spectrum due to modulation out to less than 1800 kHz offset

Power level

power levels in dB relative to the

measurement at FT

Frequency offset (kHz)

(dBm)

100

200

250

400

 600

³ 1 200

< 1 200

< 1 800

Case 1

³ 33

+0,5

‑30

‑33

‑60

‑60

‑60

32

+0,5

‑30

‑33

‑60

‑60

‑60

30

+0,5

‑30

‑33

‑60*

‑60

‑60

28

+0,5

‑30

‑33

‑60*

‑60

‑60

26

+0,5

‑30

‑33

‑60*

‑60

‑60

£ 24

+0,5

‑30

‑33

‑60*

‑60

‑60

Power

[100]

[200]

[250]

[400]

[600]

 [800]

Level

< 1 800

Case 2

³ 33

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

[-60]

32

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

[-60]

30

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

[-60]

28

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

[-60]

26

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

[-60]

£ 24

[+0,5]

[-12.3]

[-25][**]

[-40][***]

[-55]

[-60]

The values above are subject to the minimum absolute levels (dBm) below.

-36

-36

-36

-36

-56

-56

NOTE: * For equipment supporting QPSK, 8-PSK, 16-QAM or 32-QAM, the requirement for these modulations is ‑54 dB.

NOTE: ** The requirement shall be [tbd] when the wideband pulse shaping filter with the tight spectrum mask is indicated (see Pulse Format Information Element in 3GPP TS 44.060).

NOTE: *** the requirement shall be [tbd] when the wide pulse shaping filter with the tight spectrum mask is indicated (see Pulse Format Information Element in 3GPP TS 44.060).

NOTE 1: For frequency offsets between 100 kHz and 600 kHz the requirement is derived by a linear interpolation between the points identified in the table with linear frequency and power in dB relative.

b) For the modulation sidebands from 1 800 kHz offset from the carrier frequency (FT) and out to 2 MHz beyond the edge of the relevant transmit band, measured in step d), the measured power level in dB relative to the power level measured at FT, shall not exceed the values shown in table 13.17.4a-4 for GSM 400, GSM 700, GSM 850 and GSM 900 or 13.17.4a-5 for DCS 1800 or 13.17.4a-6 for PCS 1900 according to the actual transmit power, frequency offset from FT and system on which the MS is designed to operate. However any failures in the combined range 1 800 kHz to 6 MHz above and below the carrier may be counted towards the exceptions allowed in test requirements c) below, and any other failures may be counted towards the exceptions allowed in test requirements d) below.

Table 13.17.4a-4: GSM 400, GSM 700, GSM 850 and GSM 900 Spectrum due to modulation from 1 800 kHz offset to the edge of the transmit band (wideband noise)

Power level

power levels in dB relative to the

measurement at FT

Frequency offset (kHz)

(dBm)

 1 800

 3 000

 6 000

< 3 000

< 6 000

Case 1

 39

‑66

‑69

‑71

37

‑64

‑67

‑69

35

‑62

‑65

‑67

 33

‑60

‑63

‑65

Power

 [800]

 1 800

 3 000

 6 000

level

< 1 800

< 3 000

< 6 000

Case 2

 39

[-60]

[-63]

[-65]

[-71]

[-71]

[-71]

[-71]

37

[-60]

[-63]

[-65]

35

[-60]

[-63]

[-65]

 33

[-60]

[-63]

[-65]

The values above are subject to the minimum absolute levels (dBm) below.

-46

-46

-46

-46

NOTE: * For equipment supporting QPSK, 8-PSK, 16-QAM or 32-QAM, the requirement for these modulations is ‑54 dB.

NOTE: ** The requirement shall be [tbd] when the wideband pulse shaping filter with the tight spectrum mask is indicated (see Pulse Format Information Element in 3GPP TS 44.060).

NOTE: *** the requirement shall be [tbd] when the wide pulse shaping filter with the tight spectrum mask is indicated (see Pulse Format Information Element in 3GPP TS 44.060).

Table 13.17.4a-5: DCS 1800 Spectrum due to modulation from 1800 kHz offset to the edge of the transmit band (wideband noise)

Power level

power levels in dB relative to the

measurement at FT

Frequency offset (kHz)

(dBm)

 1 800

 6 000

< 6 000

Case 1

 36

‑71

‑79

34

‑69

‑77

32

‑67

‑75

30

‑65

‑73

28

‑63

‑71

26

‑61

‑69

 24

‑59

‑67

Power

 [800]

 1 800

 3 000

 6 000

Level

< 1 800

< 3 000

< 6 000

Case 2

 36

[-60]

[-63]

[-65]

[-71]

[-71]

[-71]

[-71]

[-71]

[-71]

[-71]

34

[-60]

[-63]

[-65]

32

[-60]

[-63]

[-65]

30

[-60]

[-63]

[-65]

28

[-60]

[-63]

[-65]

26

[-60]

[-63]

[-65]

 24

[-60]

[-63]

[-65]

The values above are subject to the minimum absolute levels (dBm) below.

-51

-51

-51

-51

NOTE: * For equipment supporting QPSK, 8-PSK, 16-QAM or 32-QAM, the requirement for these modulations is ‑54 dB.

NOTE: ** The requirement shall be [tbd] when the wideband pulse shaping filter with the tight spectrum mask is indicated (see Pulse Format Information Element in 3GPP TS 44.060).

NOTE: *** the requirement shall be [tbd] when the wide pulse shaping filter with the tight spectrum mask is indicated (see Pulse Format Information Element in 3GPP TS 44.060).

Table 13.17.4a-6: PCS 1900 Spectrum due to modulation from 1800 kHz offset to the edge of the transmit band (wideband noise)

Power level

power levels in dB relative to the

measurement at FT

Frequency offset (kHz)

(dBm)

³ 1 800

³ 6 000

< 6 000

Case 1

³ 33

‑68

‑76

32

‑67

‑75

30

‑65

‑73

28

‑63

‑71

26

‑61

‑69

£ 24

‑59

‑67

Power

 1 800

 3 000

 6 000

Level

< 3 000

< 6 000

Case 2

³ 33

[-63]

[-65]

[-71]

[-71]

[-71]

[-71]

[-71]

[-71]

32

[-63]

[-65]

30

[-63]

[-65]

28

[-63]

[-65]

26

[-63]

[-65]

£ 24

[-63]

[-65]

The values above are subject to the minimum absolute levels (dBm) below.

-51

-51

-51

NOTE: * For equipment supporting QPSK, 8-PSK, 16-QAM or 32-QAM, the requirement for these modulations is ‑54 dB.

NOTE: ** The requirement shall be [tbd] when the wideband pulse shaping filter with the tight spectrum mask is indicated (see Pulse Format Information Element in 3GPP TS 44.060).

NOTE: *** the requirement shall be [tbd] when the wide pulse shaping filter with the tight spectrum mask is indicated (see Pulse Format Information Element in 3GPP TS 44.060).

c) Any failures (from a) and b) above) in the combined range 600 kHz to 6 MHz above and below the carrier should be re-checked for allowed spurious emissions. For each of the three ARFCN used, spurious emissions are allowed in up to three 200 kHz bands centred on an integer multiple of 200 kHz so long as no spurious emission exceeds -36 dBm. Any spurious emissions measured in a 30 kHz bandwidth which spans two 200 kHz bands can be counted towards either 200 kHz band, whichever minimizes the number of 200 kHz bands containing spurious exceptions.

d) Any failures (from b) above) beyond 6 MHz offset from the carrier should be re-checked for allowed spurious emissions. For each of the three ARFCN used, up to twelve spurious emissions are allowed so long as no spurious emission exceeds -36 dBm.

e) The MS spurious emissions in the bands 390.2 – 400 MHz and 420.2 – 430 MHz , 460,4 MHz to 467,6 MHz, 488,8 MHz to 496 MHz, 851- 866 MHz , 921 – 925 MHz, 925 MHz to 935 MHz, 935 MHz to 960 MHz, 1 805 MHz to 1 880 MHz, 1 850 MHz to 1 910 MHz, 1900 – 1920 MHz, 1920 – 1980 MHz, 2010 – 2025 MHz, 2110 – 2170 MHz and 2300-2400 MHz measured in step d), for all types of MS, shall not exceed the values shown in table 13.16.4-4.

As exceptions up to five measurements with a level up to ‑36 dBm are permitted in each of the bands 851MHz to 866 MHz, 925 MHz to 960 MHz, 1 805 MHz to 1 880 MHz, 1900 – 1920 MHz, 1920 – 1980 MHz, 2010 – 2025 MHz, and 2110 – 2170 MHz for each ARFCN used in the measurements. For GSM 400 MS, in addition, exceptions up to three measurements with a level up to ‑36 dBm are permitted in each of the bands 460,4 MHz to 467,6 MHz and 488,8 MHz to 496 MHz for each ARFCN used in the measurements.

A maximum of five exceptions with a level up to -36 dBm are permitted in each of the band 728 MHz to 746 MHz, 747 MHz to 763 MHz, 869 MHz to 894 MHz and 1 930 MHz to 1 990 MHz for each ARFCN used in the measurements.

Table 13.17.4a-7: Spurious emissions in the MS receive bands

Band

Spurious emissions level for GSM 400, GSM 900 and DCS 1800

Spurious emissions level for GSM 700, GSM 850 and PCS 1 900

(MHz)

(dBm)

(dBm)

390 to 430

-62 Applicable only for GSM 400 mobiles T-GSM 380 and T-GSM 410

460 to 496

-67 Applicable only for GSM 400 mobiles

851- 866

-79 Applicable only for T-GSM 810 MS

921 – 925

-60 Applicable only for R-GSM MS

918 – 925

-60 Applicable only for ER-GSM MS

925 to 935

-67

935 to 960

-79

1 805 to 1 880

1900 to1980

2010 to 2025

2110-2170

2300-2400

-71

-66

-66

-66

-66

728 to 736

-73

736 to 746

-79

747 to 757

-79

757 to763

-73

869 to 894

-79

1 930 to 1 990

-71

1 850 to 1 910

Comply with FCC rules for wideband PCS services (see 3GPP TS 05.05, subclause 4.3, applicable only for PCS)

f) For the power ramp sidebands of steps h), i) and k) the power levels must not exceed the values shown in table 13.17.4a-8 for GSM 700, GSM 850 and GSM 900 or table 13.17.4a-9 for DCS 1 800 and PCS 1900.

Table 13.17.4a-8: GSM700, GSM 850 and GSM 900 Spectrum due to switching transients

Power level

Maximum level for various offsets from carrier frequency

400 kHz

600 kHz

1 200 kHz

1 800 kHz

39 dBm

-13 dBm

-21 dBm

-21 dBm

-24 dBm

37 dBm

-15 dBm

-21 dBm

-21 dBm

-24 dBm

35 dBm

-17 dBm

-21 dBm

-21 dBm

-24 dBm

33 dBm

-19 dBm

-21 dBm

-21 dBm

-24 dBm

31 dBm

-21 dBm

-23 dBm

-23 dBm

-26 dBm

29 dBm

-23 dBm

-25 dBm

-25 dBm

-28 dBm

27 dBm

-23 dBm

-26 dBm

-27 dBm

-30 dBm

25 dBm

-23 dBm

-26 dBm

-29 dBm

-32 dBm

23 dBm

-23 dBm

-26 dBm

-31 dBm

-34 dBm

<= +21 dBm

-23 dBm

-26 dBm

-32 dBm

-36 dBm

Table 13.17.4a-9: DCS 1 800/PCS 1 900 Spectrum due to switching transients

Power level

Maximum level for various offsets from carrier frequency

400 kHz

600 kHz

1 200 kHz

1 800 kHz

36 dBm

-16 dBm

-21 dBm

-21 dBm

-24 dBm

34 dBm

-18 dBm

-21 dBm

-21 dBm

-24 dBm

32 dBm

-20 dBm

-22 dBm

-22 dBm

-25 dBm

30 dBm

-22 dBm

-24 dBm

-24 dBm

-27 dBm

28 dBm

-23 dBm

-25 dBm

-26 dBm

-29 dBm

26 dBm

-23 dBm

-26 dBm

-28 dBm

-31 dBm

24 dBm

-23 dBm

-26 dBm

-30 dBm

-33 dBm

22 dBm

-23 dBm

-26 dBm

-31 dBm

-35 dBm

<= +20 dBm

-23 dBm

-26 dBm

-32 dBm

-36 dBm

NOTE 2: These figures are different from the requirements in 3GPP TS 05.05 because at higher power levels it is the modulation spectrum which is being measured using a peak hold measurement. This allowance is given in the table.

NOTE 3: The figures for table 13.17.3-5 and table 13.17.3-6 assume that, using the peak hold measurement, the lowest level measurable is 8 dB above the level of the modulation specification using the 30 kHz bandwidth gated average technique for 400 kHz offset from the carrier. At 600 and 1 200 kHz offset the level is 6 dB above and at 1 800 kHz offset the level is 3 dB above. The figures for 1 800 kHz have assumed the 30 kHz bandwidth spectrum due to modulation specification at <1 800 kHz.