31.1 Number identification supplementary services

3GPP51.010-1Mobile Station (MS) conformance specificationPart 1: Conformance specificationTS

31.1.1 CLIP

31.1.1.1 Normal operation

Conformance requirement:

3GPP TS 04.81 subclause 1.1.

Purpose:

To test that the MS presents to the user the calling number presented to it in an incoming SETUP message.

Specific PICS Statements

– Supported MT circuit switched basic services (TSPC_AddInfo_MTsvc)

PIXIT Statements

– Description of display for CLIP.

– Support of displaying the calling party subaddress.

Initial conditions

System Simulator:

1 cell, default parameters.

Mobile Station:

The MS is in MM-state "idle, updated" with valid TMSI and CKSN.

The SIM in the MS under test has CLIP enabled.

Foreseen final state of the MS

State U7

Maximum duration of test

30 s.

Procedure:

Set up an MT call to the MS under test. The SETUP message shall include a calling party BCD number information element and a calling party subaddress information element.

Expected sequence

Step

Direction

Message

Comments

1

SS -> MS

PAGING REQUEST

SS sends paging

2

MS -> SS

CHANNEL REQUEST

3

SS -> MS

IMMEDIATE ASSIGNMENT

(SDCCH)

4

MS -> SS

PAGING RESPONSE

5

SS -> MS

AUTHENTICATION REQUEST

6

MS -> SS

AUTHENTICATION RESPONSE

7

SS -> MS

CIPHERING MODE COMMAND

8

MS -> SS

CIPHERING MODE COMPLETE

9

SS -> MS

SETUP

Shall include a valid calling party BCD number and calling party subaddress

10

MS -> SS

CALL CONFIRMED

11

MS -> SS

ALERTING

12

MS

Depending on the PICS, the MS shall display the calling party BCD number and calling party subaddress

31.1.1.2 Interrogation

31.1.1.2.1 Interrogation accepted

Conformance requirement:

3GPP TS 04.81 subclause 1.2.

Test purpose

To test the correct operation of the interrogation procedure, and correct display of the response from the SS in the case of successful interrogation.

Initial conditions

System Simulator:

1 cell, default parameters.

Mobile Station:

The MS is "idle updated".

Specific PICS Statements

PIXIT Statements

– Description of the user’s commands and of display of the answers from the network for interrogation of CLIP.

Foreseen final state of the MS

The MS is "idle updated".

Test procedure

By means of appropriate MMI functions (using either 3GPP TS 02.30 or manufacturer defined MMI), the user requests interrogation of CLIP for all basic service groups.

Upon receipt of the operation (in a REGISTER message), the system simulator answers with a RELEASE COMPLETE message with the Facility information element containing the return result of the InterrogateSS operation.

The SS transaction is released and the dedicated channel is released.

Maximum duration of test

3 minutes.

Expected sequence

Step

Direction

Message

Comments

1

MS

The MS is made to initiate an interrogation of CLIP (all)

2

MS -> SS

CHANNEL REQUEST

with establishment cause "Other procedures which can be completed with an SDCCH"

3

SS -> MS

IMMEDIATE ASSIGNMENT

4

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

5

SS -> MS

CM SERVICE ACCEPT

6

MS -> SS

REGISTER

7

SS -> MS

RELEASE COMPLETE

InterrogateSS operation Return_result

8

SS -> MS

CHANNEL RELEASE

Specific message content

step 6 – CLIP

– protocol discriminator: non call related SS message.

– message type: REGISTER.

– facility:

invoke = Interrogation

Supplementary service code = CLIP.

Basic service code: no Bearer Service present, no teleservice present.

31.1.1.2.2 Interrogation rejected

Conformance requirement

3GPP TS 04.81 subclause 1.2.

Test purpose

To test the correct operation of the interrogation procedure, and correct display of the response from the SS in the case of an error response and an invoke problem.

Initial conditions

System Simulator:

1 cell, default parameters.

Mobile Station:

The MS is in CC state U10.

Specific PICS Statements

PIXIT Statements

– Description of the user’s commands and of display of the answers from the network for interrogation of CLIP.

Foreseen final state of the MS

The MS is in CC state U10.

Test procedure

By means of appropriate MMI functions (using either 3GPP TS 02.30 or manufacturer defined MMI), the user requests interrogation of CLIP for all basic service groups.

Upon receipt of the operation (in a REGISTER message),the system simulator answers with a RELEASE COMPLETE message with the Facility information element containing a Return_error(error: SS not available) of the InterrogateSS operation.

The system simulator sends STATUS ENQUIRY, the MS responds with STATUS message indicating CC state U10.

Then again, by means of appropriate MMI functions as defined by the basic public MMI described in 3GPP TS 02.30, the user requests interrogation of CLIP for all basic service groups.

Upon receipt of the REGISTER message, the system simulator answers with the RELEASE COMPLETE message (same PD and TI that in the REGISTER message) with the Facility information element containing a reject(invoke_problem: resource limitation) of the InterrogateSS operation.

The system simulator sends STATUS ENQUIRY, the MS responds with STATUS message indicating CC state U10.

Maximum duration of test

3 minutes.

Expected sequence

Step

Direction

Message

Comments

1

MS

The MS is made to initiate an interrogation for CLIP (all)

2

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

3

SS -> MS

CM SERVICE ACCEPT

4

MS -> SS

REGISTER

5

SS -> MS

RELEASE COMPLETE

InterrogateSS operation Return_error

6

SS -> MS

STATUS ENQUIRY

7

MS -> SS

STATUS

CC state U10

8

MS

The MS is made to initiate an interrogation of CLIP (all)

9

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

10

SS -> MS

CM SERVICE ACCEPT

11

MS -> SS

REGISTER

12

SS -> MS

RELEASE COMPLETE

InterrogateSS operation Reject

13

MS

provide correct MMI user indication

14

SS -> MS

STATUS ENQUIRY

15

MS -> SS

STATUS

CC state U10

Specific message content

step 4, 11 – CLIP

– protocol discriminator: non call related SS message.

– message type: REGISTER.

– facility:

invoke = Interrogation

Supplementary service code = CLIP.

Basic service code:no Bearer Service present, no teleservice present.

step 5 – CLIP

– protocol discriminator: non call related SS message.

– transaction identifier: same TI as previous REGISTER message.

– message type: RELEASE COMPLETE.

– facility:

return error code: SS not available.

For the return error the invoke ID must be the same as in the invoke of the InterrogateSS operation.

step 12 –

– protocol discriminator: non call related SS message.

– transaction identifier: same TI as previous REGISTER message.

– message type: RELEASE COMPLETE.

– facility:

reject code: resource limitation.

For the reject the invoke ID must be the same as in the invoke of the InterrogateSS operation.

31.1.2 CLIR

31.1.2.1 Normal operation – requesting presentation of CLI

Conformance requirement:

3GPP TS 04.81 subclause 2.2.

Test Purpose

To test that when the CLIR presentation mode is temporary (presentation restricted), it is possible for the subscriber to present his CLI on a per call basis.

Method of test

Specific PICS Statements

– Supported MO circuit switched basic services (TSPC_AddInfo_MOsvc)

PIXIT Statements

Initial conditions

System Simulator:

1 cell, default parameters.

Mobile Station:

The SIM in the MS under test has CLIR enabled with CLIR presentation mode "temporary (presentation restricted)".

The MS is in MM-state "idle, updated" with valid TMSI and CKSN.

The MS is brought into the state U0.1 by using table 26.8.1.2/1.

Foreseen final state of the MS

U1, call initiated.

Maximum duration of test

30 s.

Test procedure

An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Using MMI commands, the MS is made to initiate an outgoing call with CLI presented. When the MS is requesting a MM-connection, the SS will indicate acceptance by sending a CM SERVICE ACCEPT message. The MS shall respond with SETUP. The SETUP message shall contain the CLIR suppression information element.

Expected sequence

Step

Direction

Message

Comments

1

SS -> MS

CM SERVICE ACCEPT

2

MS -> SS

SETUP

with CLIR suppression information element

31.1.2.2 Normal operation – requesting restriction of CLI presentation

Conformance requirement:

3GPP TS 04.81 subclause 2.3.

Test Purpose

To test that when the CLIR presentation mode is temporary (presentation allowed), it is possible for the subscriber to present his CLI on a per call basis.

Procedure

Using MMI commands, the MS is made to initiate an outgoing call with CLI restricted.

Requirements:

The SETUP message sent by the MS shall include the CLIR invocation information element.

Method of test

Specific PICS Statements

– Supported MO circuit switched basic services (TSPC_AddInfo_MOsvc)

PIXIT Statements

Initial conditions

System Simulator:

1 cell, default parameters.

Mobile Station:

The SIM in the MS under test has CLIR enabled with CLIR presentation mode "temporary (presentation allowed)".

The MS is in MM-state "idle, updated" with valid TMSI and CKSN.

The MS is brought into the state U0.1 by using table 26.8.1.2/1.

Foreseen final state of the MS

U1, call initiated.

Maximum duration of test

30 s.

Test procedure

An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Using MMI commands, the MS is made to initiate an outgoing call with CLI restricted. When the MS is requesting a MM-connection, the SS will indicate acceptance by sending a CM SERVICE ACCEPT message. The MS shall respond with SETUP. The SETUP message sent by the MS shall include the CLIR invocation information element.

Expected sequence

Step

Direction

Message

Comments

1

SS -> MS

CM SERVICE ACCEPT

2

MS -> SS

SETUP

with CLIR invocation information element

31.1.2.3 Interrogation

31.1.2.3.1 Interrogation accepted

Conformance requirement:

3GPP TS 04.81 subclause 2.4.

Applicability

MS supporting the CLIR supplementary service.

Test purpose

To test the correct operation of the interrogation procedure, and correct display of the response from the SS in the case of successful interrogation.

Initial conditions

System Simulator:

1 cell, default parameters.

Mobile Station:

The MS is "idle updated".

Specific PICS Statements

PIXIT Statements

– Description of the user’s commands and of display of the answers from the network for interrogation of CLIR.

Foreseen final state of the MS

The MS is "idle updated".

Test procedure

By means of appropriate MMI functions (using either 3GPP TS 02.30 or manufacturer defined MMI), the user requests interrogation of CLIR for all basic service groups.

Upon receipt of the operation (in a REGISTER message), the system simulator answers with a RELEASE COMPLETE message with the Facility information element containing the return result of the InterrogateSS operation.

The SS transaction is released and the dedicated channel is released.

Maximum duration of test

3 minutes.

Expected sequence

Step

Direction

Message

Comments

1

MS

The MS is made to initiate an interrogation of CLIR (all)

2

MS -> SS

CHANNEL REQUEST

with establishment cause "Other procedures which can be completed with an SDCCH"

3

SS -> MS

IMMEDIATE ASSIGNMENT

4

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

5

SS -> MS

CM SERVICE ACCEPT

6

MS -> SS

REGISTER

7

SS -> MS

RELEASE COMPLETE

InterrogateSS operation Return_result

8

SS -> MS

CHANNEL RELEASE

Specific message content

step 6 – CLIR

– protocol discriminator: non call related SS message.

– message type: REGISTER.

– facility:

invoke = Interrogation:

Supplementary service code = CLIR.

Basic service code: no Bearer Service present, no teleservice present.

31.1.2.3.2 Interrogation rejected

Conformance requirement

3GPP TS 04.81 subclause 2.4.

Test purpose

To test the correct operation of the interrogation procedure, and correct display of the response from the SS in the case of an error response and an invoke problem.

Initial conditions

System Simulator:

1 cell, default parameters.

Mobile Station:

The MS is in CC state U10.

Specific PICS Statements

PIXIT Statements

– Description of the user’s commands and of display of the answers from the network for interrogation of CLIR.

Foreseen final state of the MS

The MS is in CC state U10.

Test procedure

By means of appropriate MMI functions (using either 3GPP TS 02.30 or manufacturer defined MMI), the user requests interrogation of CLIR for all basic service groups.

Upon receipt of the operation (in a REGISTER message),the system simulator answers with a RELEASE COMPLETE message with the Facility information element containing a Return_error(error: SS not available) of the InterrogateSS operation.

The system simulator sends STATUS ENQUIRY, the MS responds with STATUS message indicating CC state U10.

Then again, by means of appropriate MMI functions as defined by the basic public MMI described in 3GPP TS 02.30, the user requests interrogation of CLIR for all basic service groups.

Upon receipt of the REGISTER message, the system simulator answers with the RELEASE COMPLETE message (same PD and TI that in the REGISTER message) with the Facility information element containing a reject(invoke_problem: resource limitation) of the InterrogateSS operation.

The system simulator sends STATUS ENQUIRY, the MS responds with STATUS message indicating CC state U10.

Maximum duration of test

3 minutes.

Expected sequence

Step

Direction

Message

Comments

1

MS

The MS is made to initiate an interrogation for CLIR (all)

2

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

3

SS -> MS

CM SERVICE ACCEPT

4

MS -> SS

REGISTER

5

SS -> MS

RELEASE COMPLETE

InterrogateSS operation Return_error

6

SS -> MS

STATUS ENQUIRY

7

MS -> SS

STATUS

CC state U10

8

MS

The MS is made to initiate an interrogation of CLIR (all)

9

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

10

SS -> MS

CM SERVICE ACCEPT

11

MS -> SS

REGISTER

12

SS -> MS

RELEASE COMPLETE

InterrogateSS operation Reject

13

MS

provide correct MMI user indication

14

SS -> MS

STATUS ENQUIRY

15

MS -> SS

STATUS

CC state U10

Specific message content

step 4, 11 – CLIR

– protocol discriminator: non call related SS message.

– message type: REGISTER.

– facility:

invoke = Interrogation:

Supplementary service code = CLIR.

Basic service code:no Bearer Service present, no teleservice present.

step 5 – CLIR

– protocol discriminator: non call related SS message.

– transaction identifier: same TI as previous REGISTER message.

– message type: RELEASE COMPLETE.

– facility:

return error code: SS not available.

For the return error the invoke ID must be the same as in the invoke of the InterrogateSS operation.

step 12 –

– protocol discriminator: non call related SS message.

– transaction identifier: same TI as previous REGISTER message.

– message type: RELEASE COMPLETE.

– facility:

reject code: resource limitation.

For the reject the invoke ID must be the same as in the invoke of the InterrogateSS operation.

31.1.3 COLP

31.1.3.1 Normal operation

Conformance requirement:

3GPP TS 04.81 subclause 3.1.

Purpose:

To test that the MS displays the connected number presented to it in an incoming CONNECT message.

Method of test

Specific PICS Statements

– Supported MO circuit switched basic services (TSPC_AddInfo_MOsvc)

PIXIT Statements

– Description of display for COLP.

Initial conditions

System Simulator:

1 cell, default parameters.

Mobile Station:

The SIM in the MS under test has COLP enabled.

The MS is in MM-state "idle, updated" with valid TMSI and CKSN.

The MS is brought into the state U1 by using table 26.8.1.2/4.

Foreseen final state of the MS

U10, call active.

Maximum duration of test

30 s.

Test procedure

1. An MO circuit switched basic service is selected that is supported by the MS; if the MS supports MO telephony, the selected basic service is telephony. If necessary, the MS is configured for that basic service. Then, the MS is made to initiate a call. The CC entity of the MS is brought to the state U4. The SS sends a CONNECT message to the MS containing a connected number information element and a connected party subaddress information element. The MS shall respond by sending a CONNECT ACKNOWLEDGE message. The MS shall correctly display the connected line information.

Expected sequence, procedure 1

Step

Direction

Message

Comments

1

SS -> MS

CONNECT

See specific message contents

2

MS -> SS

CONNECT ACKNOWLEDGE

3

MS

The MS shall correctly display the connected line information

Specific message contents

CONNECT

Connected number information element

Presentation indicator

Presentation allowed

Screening indicator

User provided, not screened

Connected subaddress

Any valid subaddress

31.1.3.2 Interrogation

31.1.3.2.1 Interrogation accepted

Conformance requirement:

3GPP TS 04.81 subclause 3.2.

Test purpose

To test the correct operation of the interrogation procedure, and correct display of the response from the SS in the case of successful interrogation.

Initial conditions

System Simulator:

1 cell, default parameters.

Mobile Station:

The MS is "idle updated".

Specific PICS Statements

PIXIT Statements

– Description of the user’s commands and of display of the answers from the network for interrogation of COLP.

Foreseen final state of the MS

The MS is "idle updated".

Test procedure

By means of appropriate MMI functions (using either 3GPP TS 02.30 or manufacturer defined MMI), the user requests interrogation of COLP for all basic service groups.

Upon receipt of the operation (in a REGISTER message), the system simulator answers with a RELEASE COMPLETE message with the Facility information element containing the return result of the InterrogateSS operation.

The SS transaction is released and the dedicated channel is released.

Maximum duration of test

3 minutes.

Expected sequence

Step

Direction

Message

Comments

1

MS

The MS is made to initiate an interrogation of COLP (all)

2

MS -> SS

CHANNEL REQUEST

with establishment cause "Other procedures which can be completed with an SDCCH"

3

SS -> MS

IMMEDIATE ASSIGNMENT

4

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

5

SS -> MS

CM SERVICE ACCEPT

6

MS -> SS

REGISTER

7

SS -> MS

RELEASE COMPLETE

InterrogateSS operation Return_result

8

SS -> MS

CHANNEL RELEASE

Specific message content

step 6 – COLP

– protocol discriminator: non call related SS message.

– message type: REGISTER.

– facility:

invoke = Interrogation:

Supplementary service code = COLP.

Basic service code: no Bearer Service present, no teleservice present.

31.1.3.2.2 Interrogation rejected

Conformance requirement

3GPP TS 04.81 subclause 3.2.

Test purpose

To test the correct operation of the interrogation procedure, and correct display of the response from the SS in the case of an error response and an invoke problem.

Initial conditions

System Simulator:

1 cell, default parameters.

Mobile Station:

The MS is in CC state U10.

Specific PICS Statements

PIXIT Statements

– Description of the user’s commands and of display of the answers from the network for interrogation of COLP.

Foreseen final state of the MS

The MS is in CC state U10.

Test procedure

By means of appropriate MMI functions (using either 3GPP TS 02.30 or manufacturer defined MMI), the user requests interrogation of COLP for all basic service groups.

Upon receipt of the operation (in a REGISTER message),the system simulator answers with a RELEASE COMPLETE message with the Facility information element containing a Return_error(error: SS not available) of the InterrogateSS operation.

The system simulator sends STATUS ENQUIRY, the MS responds with STATUS message indicating CC state U10.

Then again, by means of appropriate MMI functions as defined by the basic public MMI described in 3GPP TS 02.30, the user requests interrogation of COLP for all basic service groups.

Upon receipt of the REGISTER message, the system simulator answers with the RELEASE COMPLETE message (same PD and TI that in the REGISTER message) with the Facility information element containing a reject(invoke_problem: resource limitation) of the InterrogateSS operation.

The system simulator sends STATUS ENQUIRY, the MS responds with STATUS message indicating CC state U10.

Maximum duration of test

3 minutes.

Expected sequence

Step

Direction

Message

Comments

1

MS

The MS is made to initiate an interrogation for COLP (all)

2

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

3

SS -> MS

CM SERVICE ACCEPT

4

MS -> SS

REGISTER

5

SS -> MS

RELEASE COMPLETE

InterrogateSS operation Return_error

6

SS -> MS

STATUS ENQUIRY

7

MS -> SS

STATUS

CC state U10

8

MS

The MS is made to initiate an interrogation of COLP (all)

9

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

10

SS -> MS

CM SERVICE ACCEPT

11

MS -> SS

REGISTER

12

SS -> MS

RELEASE COMPLETE

InterrogateSS operation Reject

13

MS

provide correct MMI user indication

14

SS -> MS

STATUS ENQUIRY

15

MS -> SS

STATUS

CC state U10

Specific message content

step 4, 11 – COLP

– protocol discriminator: non call related SS message.

– message type: REGISTER.

– facility:

invoke = Interrogation:

Supplementary service code = COLP.

Basic service code:no Bearer Service present, no teleservice present.

step 5 – COLP

– protocol discriminator: non call related SS message.

– transaction identifier: same TI as previous REGISTER message.

– message type: RELEASE COMPLETE.

– facility:

return error code: SS not available.

For the return error the invoke ID must be the same as in the invoke of the InterrogateSS operation.

step 12 –

– protocol discriminator: non call related SS message.

– transaction identifier: same TI as previous REGISTER message.

– message type: RELEASE COMPLETE.

– facility:

reject code: resource limitation.

For the reject the invoke ID must be the same as in the invoke of the InterrogateSS operation.

31.1.4 COLR

31.1.4.1 Interrogation

31.1.4.1.1 Interrogation accepted

Conformance requirement:

3GPP TS 04.81 subclause 4.2.

Test purpose

To test the correct operation of the interrogation procedure, and correct display of the response from the SS in the case of successful interrogation.

Initial conditions

System Simulator:

1 cell, default parameters.

Mobile Station:

The MS is "idle updated".

Specific PICS Statements

PIXIT Statements

– Description of the user’s commands and of display of the answers from the network for interrogation of COLR.

Foreseen final state of the MS

The MS is "idle updated".

Test procedure

By means of appropriate MMI functions (using either 3GPP TS 02.30 or manufacturer defined MMI), the user requests interrogation of COLR for all basic service groups.

Upon receipt of the operation (in a REGISTER message), the system simulator answers with a RELEASE COMPLETE message with the Facility information element containing the return result of the InterrogateSS operation.

The SS transaction is released and the dedicated channel is released.

Maximum duration of test

3 minutes.

Expected sequence

Step

Direction

Message

Comments

1

MS

The MS is made to initiate an interrogation of COLR (all)

2

MS -> SS

CHANNEL REQUEST

with establishment cause "Other procedures which can be completed with an SDCCH"

3

SS -> MS

IMMEDIATE ASSIGNMENT

4

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

5

SS -> MS

CM SERVICE ACCEPT

6

MS -> SS

REGISTER

7

SS -> MS

RELEASE COMPLETE

InterrogateSS operation Return_result

8

SS -> MS

CHANNEL RELEASE

Specific message content

step 6 – COLR

– protocol discriminator: non call related SS message.

– message type: REGISTER.

– facility:

invoke = Interrogation:

Supplementary service code = COLR.

Basic service code: no Bearer Service present, no teleservice present.

31.1.4.1.2 Interrogation rejected

Conformance requirement

3GPP TS 04.81 subclause 4.2.

Test purpose

To test the correct operation of the interrogation procedure, and correct display of the response from the SS in the case of an error response and an invoke problem.

Initial conditions

System Simulator:

1 cell, default parameters.

Mobile Station:

The MS is in CC state U10.

Specific PICS Statements

PIXIT Statements

– Description of the user’s commands and of display of the answers from the network for interrogation of COLR.

Foreseen final state of the MS

The MS is in CC state U10.

Test procedure

By means of appropriate MMI functions (using either 3GPP TS 02.30 or manufacturer defined MMI), the user requests interrogation of COLR for all basic service groups.

Upon receipt of the operation (in a REGISTER message),the system simulator answers with a RELEASE COMPLETE message with the Facility information element containing a Return_error(error: SS not available) of the InterrogateSS operation.

The system simulator sends STATUS ENQUIRY, the MS responds with STATUS message indicating CC state U10.

Then again, by means of appropriate MMI functions as defined by the basic public MMI described in 3GPP TS 02.30, the user requests interrogation of COLR for all basic service groups.

Upon receipt of the REGISTER message, the system simulator answers with the RELEASE COMPLETE message (same PD and TI that in the REGISTER message) with the Facility information element containing a reject(invoke_problem: resource limitation) of the InterrogateSS operation.

The system simulator sends STATUS ENQUIRY, the MS responds with STATUS message indicating CC state U10.

Maximum duration of test

3 minutes.

Expected sequence

Step

Direction

Message

Comments

1

MS

The MS is made to initiate an interrogation for COLR (all)

2

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

3

SS -> MS

CM SERVICE ACCEPT

4

MS -> SS

REGISTER

5

SS -> MS

RELEASE COMPLETE

InterrogateSS operation Return_error

6

SS -> MS

STATUS ENQUIRY

7

MS -> SS

STATUS

CC state U10

8

MS

The MS is made to initiate a interrogation of COLR (all)

9

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

10

SS -> MS

CM SERVICE ACCEPT

11

MS -> SS

REGISTER

12

SS -> MS

RELEASE COMPLETE

InterrogateSS operation Reject

13

MS

provide correct MMI user indication

14

SS -> MS

STATUS ENQUIRY

15

MS -> SS

STATUS

CC state U10

Specific message content

step 4, 11 – COLR

– protocol discriminator: non call related SS message.

– message type: REGISTER.

– facility:

invoke = Interrogation:

Supplementary service code = COLR.

Basic service code:no Bearer Service present, no teleservice present.

step 5 – COLR

– protocol discriminator: non call related SS message.

– transaction identifier: same TI as previous REGISTER message.

– message type: RELEASE COMPLETE.

– facility:

return error code: SS not available.

For the return error the invoke ID must be the same as in the invoke of the InterrogateSS operation.

step 12 –

– protocol discriminator: non call related SS message.

– transaction identifier: same TI as previous REGISTER message.

– message type: RELEASE COMPLETE.

– facility:

reject code: resource limitation.

For the reject the invoke ID must be the same as in the invoke of the InterrogateSS operation.

31.1.4.2 Void

31.1.5 CNAP

31.1.5.1.1 Normal Operation – Name indication contained in Setup message

Conformance requirements

3GPP TS 24.096 subclause 4.1

Purpose

To test that the MS presents to the user the name information of the calling party to the called party at call setup time for all incoming calls.

Specific PICS Statements

– Supported MT circuit switched basic services (TSPC_AddInfo_MTsvc)

PIXIT Statements

– Description of display for CNAP.

Initial Conditions

System Simulator:

1 cell, default parameters

Mobile Station:

The MS is in MM-state “idle, updated” with valid TMSI and CKSN

Foreseen final state of the MS

Stae U7

Maximum Duration of Test

3 minutes.

Procedure

Set up an MT Call to the MS under test. The SS sends the Name Indication in the Facilty IE of the CC Setup

Expected Sequence

Step

Direction

Message

Comments

1

SS -> MS

PAGING REQUEST

SS sends paging

2

MS -> SS

CHANNEL REQUEST

3

SS -> MS

IMMEDIATE ASSIGNMENT

(SDCCH)

4

MS -> SS

PAGING RESPONSE

5

SS -> MS

AUTHENTICATION REQUEST

6

MS -> SS

AUTHENTICATION RESPONSE

7

SS -> MS

CIPHERING MODE COMMAND

8

MS -> SS

CIPHERING MODE COMPLETE

9

SS -> MS

SETUP

Shall include Facility (Invoke = NotifySS (CNAP, nameIndicator ))

Signal IE included

10

MS -> SS

CALL CONFIRMED

11

MS -> SS

ALERTING

12

MS

Depending on the PICS, the MS shall display the calling nameIndicator

Specific message content

step 9 – CNAP nameIndicator settings:

– namePresentationAllowed

– NameSet: “TESTNAME”

31.1.5.1.2 Normal Operation – Name indication contained in Facility message

Conformance requirements

3GPP TS 24.096 subclause 4.1

Purpose

To test that the MS presents to the user the name information of the calling party to the called party at call setup time for all incoming calls.

Specific PICS Statements

– Supported MT circuit switched basic services (TSPC_AddInfo_MTsvc)

PIXIT Statements

– Description of display for CNAP.

Initial Conditions

System Simulator:

1 cell, default parameters

Mobile Station:

The MS is in MM-state “idle, updated” with valid TMSI and CKSN

Foreseen final state of the MS

Stae U7

Maximum Duration of Test

3 minutes.

Procedure

Set up an MT Call to the MS under test. The SS sends the Name Indication in a Facilty message

Expected Sequence

Step

Direction

Message

Comments

1

SS -> MS

PAGING REQUEST

SS sends paging

2

MS -> SS

CHANNEL REQUEST

3

SS -> MS

IMMEDIATE ASSIGNMENT

(SDCCH)

4

MS -> SS

PAGING RESPONSE

5

SS -> MS

AUTHENTICATION REQUEST

6

MS -> SS

AUTHENTICATION RESPONSE

7

SS -> MS

CIPHERING MODE COMMAND

8

MS -> SS

CIPHERING MODE COMPLETE

9

SS -> MS

SETUP

Signal IE included

10

MS -> SS

CALL CONFIRMED

11

MS -> SS

ALERTING

12

SS -> MS

FACILITY

Facility (Invoke=NotifiSS (CNAP, nameIndicator))

13

MS

Depending on the PICS, the MS shall display the calling nameIndicator

Specific message content

step 10 – CNAP nameIndicator settings:

– namePresentationAllowed

– NameSet: “TESTNAME”

31.1.5.2.1 Interrogation accepted

Conformance requirements

3GPP TS 24.096 subclause 4.2

Purpose

To test the correct operation of the interrogation procedure, and correct display of the response from the SS in the case of successful interrogation

Initial Conditions

System Simulator:

1 cell, default parameters

Mobile Station:

The MS is “Idle Updated”

Specific PICS Statements

PIXIT Statements

– Description of the user’s commands and of display of the answers from the network for interrogation of CNAP.

Forseen final state of the MS

The MS is Idle Updated

Maximum Duration of Test

3 minutes.

Procedure

By mean´s of appropriate MMI functions (using either 3GPP TS 02.30 or manufacturer defined MMI), the users requests interrogation of CNAP for all basic service groups.

Upon receipt of the operation (in a register message), the system simulator answers with a RELEASE COMPLETE message with the Facility information element containing the return result of the InterrogtaeSS operation .

The SS transaction is released and the dedicated channel is released

Expected Sequence

Step

Direction

Message

Comments

1

MS

The MS is made to initiate an interrogation of CNAP (all)

2

MS -> SS

CHANNEL REQUEST

with establishment cause "Other procedures which can be completed with an SDCCH"

3

SS -> MS

IMMEDIATE ASSIGNMENT

4

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

5

SS -> MS

CM SERVICE ACCEPT

6

MS -> SS

REGISTER

Facility (Invoke = InterrogateSS (CNAP))

7

SS -> MS

RELEASE COMPLETE

Facility (Return Result = InterrogateSS (ss-status))

8

SS -> MS

CHANNEL RELEASE

Specific message content

step 6 – CNAP

– protocol discriminator: non call related SS message.

– message type: REGISTER.

– facility:

invoke = Interrogation

Supplementary service code = CNAP.

Basic service code: no Bearer Service present, no teleservice present.

31.1.5.2.2 Interrogation rejected

Conformance requirements

3GPP TS 24.096 subclause 4.2

Purpose

To test the correct operation of the interrogation procedure, and correct display of the response from the SS in the case of an error response and an invoke problem.

Specific PICS Statements

PIXIT Statements

– Description of the user’s commands and of display of the answers from the network for interrogation of CNAP.

Initial Conditions

System Simulator:

1 cell, default parameters

Mobile Station:

The MS is in CC state U10

Maximum Duration of Test

3 minutes.

Procedure

By means of appropriate MMI functions (using either 3GPP TS 02.30 or manufacturer defined MMI), the user requests interrogation of CNAP for all basic service groups.

Upon receipt of the operation (in a REGISTER message),the system simulator answers with a RELEASE COMPLETE message with the Facility information element containing a Return_error (error: SS not available) of the InterrogateSS operation.

The system simulator sends STATUS ENQUIRY, the MS responds with STATUS message indicating CC state U10.

Then again, by means of appropriate MMI functions as defined by the basic public MMI described in 3GPP TS 02.30, the user requests interrogation of CNAP for all basic service groups.

Upon receipt of the REGISTER message, the system simulator answers with the RELEASE COMPLETE message (same PD and TI that in the REGISTER message) with the Facility information element containing a reject (invoke_problem: resource limitation) of the InterrogateSS operation.

The system simulator sends STATUS ENQUIRY, the MS responds with STATUS message indicating CC state U10.

Expected Sequence

Step

Direction

Message

Comments

1

MS

The MS is made to initiate an interrogation for CNAP (all)

2

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

3

SS -> MS

CM SERVICE ACCEPT

4

MS -> SS

REGISTER

5

SS -> MS

RELEASE COMPLETE

InterrogateSS operation Return_error

6

SS -> MS

STATUS ENQUIRY

7

MS -> SS

STATUS

CC state U10

8

MS

The MS is made to initiate an interrogation of CNAP (all)

9

MS -> SS

CM SERVICE REQUEST

cause: "supplementary service activation"

10

SS -> MS

CM SERVICE ACCEPT

11

MS -> SS

REGISTER

12

SS -> MS

RELEASE COMPLETE

InterrogateSS operation Reject

13

MS

provide correct MMI user indication

14

SS -> MS

STATUS ENQUIRY

15

MS -> SS

STATUS

CC state U10

Specific message content

step 4, 11 – CNAP

– protocol discriminator: non call related SS message.

– message type: REGISTER.

– facility:

invoke = Interrogation

Supplementary service code = CNAP.

Basic service code:no Bearer Service present, no teleservice present.

step 5 – CNAP

– protocol discriminator: non call related SS message.

– transaction identifier: same TI as previous REGISTER message.

– message type: RELEASE COMPLETE.

– facility:

return error code: SS not available.

For the return error the invoke ID must be the same as in the invoke of the InterrogateSS operation.

step 12 –

– protocol discriminator: non call related SS message.

– transaction identifier: same TI as previous REGISTER message.

– message type: RELEASE COMPLETE.

– facility:

reject code: resource limitation.

For the reject the invoke ID must be the same as in the invoke of the InterrogateSS operation.