26.6.11 Test of classmark
3GPP51.010-1Mobile Station (MS) conformance specificationPart 1: Conformance specificationTS
References to Class Mark related PICS values are provided in the table 26.6.11a and 26.6.11b.
Table 26.6.11a: Mobile Station Classmark 2 information element
Item |
IE |
Values |
Mnemonic |
||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 |
Revision level |
Revision level Bits
|
TSPC_Revision_Level_GSM_Phase_1 TSPC_Revision_Level_GSM_Phase_2 TSPC_Revision_Level_MS_supporting_R99_or_later |
||||||||||||||||||||||||||||||||||||||||||||||||
2 |
ES IND |
Bit 5
|
TSPC_Controlled_Early_Classmark_Sending |
||||||||||||||||||||||||||||||||||||||||||||||||
3 |
A5/1 |
|
TSPC_Feat_A51 |
||||||||||||||||||||||||||||||||||||||||||||||||
4 |
RF power capability |
When T-GSM 380, T-GSM 410, GSM 450, GSM 480, GSM 710, GSM 750, T-GSM 810, GSM 850, GSM 900 P, E T [or R] band is used Bits
Other values are reserved When the GSM 1800 or GSM 1900 band is used Bits
Other values are reserved When UMTS is used, an MS not supporting any GSM band or a multiband GSM MS Bits
Other values are reserved |
TSPC_Type_GSM_Class2 TSPC_Type_GSM_Class3 TSPC_Type_GSM_Class4 TSPC_Type_GSM_Class5 TSPC_Type_DCS_Class1 TSPC_Type_DCS_Class2 TSPC_Type_DCS_Class3 TSPC_Type_PCS_Class1 TSPC_Type_PCS_Class2 TSPC_Type_PCS_Class3 |
||||||||||||||||||||||||||||||||||||||||||||||||
5 |
PS capability |
Bit 7
|
TSPC_AddInfo_PseudoSynch |
||||||||||||||||||||||||||||||||||||||||||||||||
6 |
SS Screening Indicator |
Bits
|
TSPC_SS_Screening_Indictator_in_CM2 |
||||||||||||||||||||||||||||||||||||||||||||||||
7 |
SM capability |
Bit 4
|
TSPC_Serv_TS21 |
||||||||||||||||||||||||||||||||||||||||||||||||
8 |
VBS notification reception |
Bit 3
|
TSPC_VBS_Notification_Reception |
||||||||||||||||||||||||||||||||||||||||||||||||
9 |
VGCS notification reception |
Bit 2
|
TSPC_VCGS_Notification_Reception |
||||||||||||||||||||||||||||||||||||||||||||||||
10 |
Frequency Capability |
When a GSM 900 band is used Bit 1
|
TSPC_Type_GSM_E_Band TSPC_Type_GSM_R_Band |
||||||||||||||||||||||||||||||||||||||||||||||||
11 |
CM3 |
Bit 8
|
TSPC_ClassMK3_Info_available |
||||||||||||||||||||||||||||||||||||||||||||||||
12 |
LCS VA Capability |
Bit 6
|
TSPC_Location_Request_via_CS_Domain |
||||||||||||||||||||||||||||||||||||||||||||||||
13 |
UCS2 treatment |
Bit 5
|
TSPC_UCS2_treatment |
||||||||||||||||||||||||||||||||||||||||||||||||
14 |
SoLSA |
Bit 4
|
TSPC_SoLSA |
||||||||||||||||||||||||||||||||||||||||||||||||
15 |
CM Service Prompt |
Bit 3
|
TSPC_CM_Service_Prompt |
||||||||||||||||||||||||||||||||||||||||||||||||
16 |
A5/3 |
Bit 2
|
TSPC_Feat_A53 |
||||||||||||||||||||||||||||||||||||||||||||||||
17 |
A5/2 |
Bit 1
|
Shall not be supported anymore |
Table 26.6.11b: Mobile Station Classmark 3 Information Element
Item |
IE |
Values |
Mnemonic |
---|---|---|---|
1 |
Multiband supported |
000 101 110 001 010 100 Band 1 supported Bit 1 0 P-GSM not supported 1 P-GSM supported Band 2 supported Bit 2 0 E-GSM or R-GSM not supported 1 E-GSM or R-GSM supported Band 3 supported Bit 3 0 GSM 1800 not supported 1 GSM 1800 supported |
TSPC_Type_GSM_P_Band TSPC_Type_GSM_E_Band TSPC_Type_GSM_R_Band TSPC_Type_DCS_Band Note: Due to the shared radio frequency channel numbers between DCS 1800 and PCS 1900, even if both DCS_1800_BAND and PCS_1900_BAND are set to TRUE, the MS can only ever indicate support for one of these bands |
2 |
A5 bits |
A5/4 0 Encryption algorithm A5/4 not available 1 Encryption algorithm A5/4 available A5/5 0 Encryption algorithm A5/5 not available 1 Encryption algorithm A5/5 available A5/6 0 Encryption algorithm A5/6 not available 1 Encryption algorithm A5/6 available A5/7 0 Encryption algorithm A5/7 not available 1 Encryption algorithm A5/7 available |
TSPC_Feat_A54 A5/5 Feature is not available and should set to 0 A5/6 Feature is not available and should set to 0 A5/7 Feature is not available and should set to 0 |
3 |
Associated Radio capability 1 and 2 |
4 bit fields If either of P-GSM or E-GSM or R-GSM is supported, the radio capability 1 field indicates the radio capability for P-GSM, E-GSM or R-GSM, and the radio capability 2 field indicates the radio capability for GSM 1800 if supported, and is spare otherwise. If none of P-GSM or E-GSM or R-GSM are supported, the radio capability 1 field indicates the radio capability for GSM 1800, and the radio capability 2 field is spare. The radio capability contains the binary coding of the power class associated with the band indicated in multiband support bits (see 3GPP TS 45.005 [33]). |
TSPC_Type_GSM_Class2 TSPC_Type_GSM_Class3 TSPC_Type_GSM_Class4 TSPC_Type_GSM_Class5 TSPC_Type_DCS_Class1 TSPC_Type_DCS_Class2 TSPC_Type_DCS_Class3 |
4 |
R-GSM band Associated Radio Capability |
3 bit field In case where the R-GSM band is supported the R-GSM band associated radio capability field contains the binary coding of the power class associated (see 3GPP TS 45.005) (regardless of the number of GSM bands supported). A mobile station supporting the R-GSM band shall also when appropriate, (see 10.5.1.6) indicate its support in the ‘FC’ bit in the Mobile Station Classmark 2 information element. NOTE: The coding of the power class for P-GSM, E-GSM, R-GSM and GSM 1800 in radio capability 1 and/or 2 is different to that used in the Mobile Station Classmark 1 and Mobile Station Classmark 2 information elements. |
TSPC_Type_GSM_Class2 TSPC_Type_GSM_Class3 TSPC_Type_GSM_Class4 TSPC_Type_GSM_Class5 |
5 |
HSCSD Multi Slot Class |
5 bit field In case the MS supports the use of multiple timeslots for HSCSD then the HSCSD Multi Slot Class field is coded as the binary representation of the multislot class defined in 3GPP TS 45.002 [32]. |
TSPC_Type_HSCSD_Multislot |
6 |
UCS2 treatment |
0 the ME has a preference for the default alphabet over UCS2. 1 the ME has no preference between the use of the default alphabet and the use of UCS2. |
TSPC_UCS2_treatment |
7 |
Extended Measurement Capability |
0 the MS does not support Extended Measurements 1 the MS supports Extended Measurements |
TSPC_Extended_Measurement_Capability |
8 |
SMS_VALUE (Switch-Measure-Switch) |
Bits microseconds) microseconds) microseconds) microseconds) |
TSPC_SMS_VALUE_SMS |
9 |
SM_VALUE (Switch-Measure) |
Bits 4 3 2 1 microseconds) microseconds) microseconds) microseconds) |
TSPC_SMS_VALUE_SM |
10 |
MS Positioning Method |
MS assisted E-OTD Bit 5 0 MS assisted E-OTD not supported 1 MS assisted E-OTD supported MS based E-OTD Bit 4 0 MS based E-OTD not supported 1 MS based E-OTD supported MS assisted GPS Bit 3 0 MS assisted GPS not supported 1 MS assisted GPS supported MS based GPS Bit 2 0 MS based GPS not supported 1 MS based GPS supported MS Conventional GPS Bit 1 0 conventional GPS not supported 1 conventional GPS supported |
TSPC_EOTD_ASSIST TSPC_EOTD_MS_BASED TSPC_A-GPS_Assist TSPC_A-GPS_Based TSPC_Conv-GPS |
11 |
ECSD Multi Slot class |
An MS that supports ECSD shall include this field to indicate its ECSD capability. Whether the MS is capable of 8-PSK modulation in uplink is indicated by the value of the Modulation Capability field in the 8-PSK struct. The ECSD Multi Slot Class field is coded as the binary representation of the multislot class defined in 3GPP TS 45.002 [32]. |
TSPC_Type_ECSD_Multislot_Class |
12 |
8-PSK struct |
0 8-PSK struct not present 1 8-PSK struct present Note: The MS shall include the 8-PSK struct if it supports ECSD or DTM EGPRS or both |
TSPC_8-PSK_Struct |
13 |
Modulation Capability |
0 8-PSK supported for downlink reception only 1 8-PSK supported for uplink transmission and downlink reception |
TSPC_8-PSK_Struct TSPC_Type_DTM_EGPRS_8PSK_uplink TSPC_Type_ECSD_8PSK_uplink |
14 |
8-PSK RF Power Capability 1 |
Bits 2 1 0 0 Reserved 0 1 Power class E1 1 0 Power class E2 1 1 Power class E3 |
TSPC_8-PSK_Struct TSPC_8-PSK_PowerCap1 TSPC_Type_GSM_ClassE1 TSPC_Type_GSM_ClassE2 TSPC_Type_GSM_ClassE3 TSPC_Type_GSM_850_ClassE1 TSPC_Type_GSM_850_ClassE2 TSPC_Type_GSM_850_ClassE3 |
15 |
8-PSK RF Power Capability 2 |
Bits 2 1 0 0 Reserved 0 1 Power class E1 1 0 Power class E2 1 1 Power class E3 |
TSPC_8-PSK_Struct TSPC_8-PSK_PowerCap2 TSPC_Type_DCS_ClassE1 TSPC_Type_DCS_ClassE2 TSPC_Type_DCS_ClassE3 TSPC_Type_PCS_ClassE1 TSPC_Type_PCS_ClassE2 TSPC_Type_PCS_ClassE3 |
16 |
GSM 400 Bands Supported |
Bits GSM 450 not supported GSM 480 not supported GSM 480 supported |
TSPC_Type_GSM_450_Band TSPC_Type_GSM_480_Band |
17 |
GSM 400 Associated Radio Capability |
4 Bit field If either GSM 450 or GSM 480 or both is supported, the GSM 400 Associated Radio Capability field indicates the radio capability for GSM 450 and/or GSM 480. The radio capability contains the binary coding of the power class associated with the band indicated in GSM 400 Bands Supported bits (see 3GPP TS 45.005 [33]). NOTE: The coding of the power class for GSM 450 and GSM 480 in GSM 400 Associated Radio Capability is different to that used in the Mobile Station Classmark 1 and Mobile Station Classmark 2 information elements. |
TSPC_Type_GSM_400_Class2 TSPC_Type_GSM_400_Class3 TSPC_Type_GSM_400_Class4 TSPC_Type_GSM_400_Class5 |
18 |
GSM 850 Associated Radio Capability |
4 Bit field See the semantic rule for the sending of this field. This field indicates whether GSM 850 band is supported and its associated radio capability. The radio capability contains the binary coding of the power class associated with the GSM 850 band (see 3GPP TS 45.005 [33]). Note: the coding of the power class for GSM 850 in GSM 850 Associated Radio Capability is different to that used in the Mobile Station Classmark 1 and Mobile Station Classmark 2 information elements. |
TSPC_Type_GSM_850_Class2 TSPC_Type_GSM_850_Class3 TSPC_Type_GSM_850_Class4 TSPC_Type_GSM_850_Class5 |
19 |
GSM 1900 Associated Radio Capability |
4 Bit field See the semantic rule for the sending of this field. This field indicates whether GSM 1900 band is supported and its associated radio capability. The radio capability contains the binary coding of the power class associated with the GSM 1900 band (see 3GPP TS 45.005 [33]). Note: the coding of the power class for GSM 1900 in GSM 1900 Associated Radio Capability is different to that used in the Mobile Station Classmark 1 and Mobile Station Classmark 2 information elements. |
TSPC_Type_PCS_Class1 TSPC_Type_PCS_Class2 TSPC_Type_PCS_Class3 |
20 |
UMTS FDD Radio Access Technology Capability |
0 UMTS FDD not supported |
TSPC_Type_UTRAN_FDD |
21 |
UMTS 3.84 Mcps TDD Radio Access Technology Capability |
0 UMTS 3.84 Mcps TDD not supported |
TSPC_Type_UTRAN3.84_TDD |
22 |
CDMA 2000 Radio Access Technology Capability |
0 CDMA2000 not supported |
TSPC_CDMA2000 |
23 |
DTM GPRS Multi Slot Class |
Bit network shall interpret this as ‘01’ supported supported supported |
TSPC_DTM_GPRS_Multislot_Class_1 TSPC_DTM_GPRS_Multislot_Class_5 TSPC_DTM_GPRS_Multislot_Class_9 TSPC_DTM_GPRS_Multislot_Class_11 |
24 |
Single Slot DTM |
0 Single Slot DTM not supported |
TSPC_DTM_GPRS_Singleslot_Allocation TSPC_DTM_EGPRS_Singleslot_Allocation |
25 |
DTM EGPRS Multi Slot Class |
This field indicates the DTM GPRS multislot capabilities of the MS. It is coded as follows: If a multislot class type 1 MS indicates the support of a DTM GPRS multislot class for which three uplink timeslots can be assigned, the mobile station shall support Extended Dynamic Allocation. This field shall contain one of the following values if the DTM GPRS High Multi Slot Class field is present:
The same multislot capability is applicable also for EGPRS2 if supported. |
TSPC_DTM_EGPRS_Multislot_Class_5 TSPC_DTM_EGPRS_Multislot_Class_9 TSPC_DTM_EGPRS_Multislot_Class_11 |
26 |
Single Band Support |
This field shall be sent if the mobile station supports UMTS and one and only one GSM band with the exception of R-GSM; this field shall not be sent otherwise |
TSPC_SingleBand_Support |
27 |
GSM Band |
Bits 4 3 2 1 0 0 0 0 E-GSM supported 0 0 0 1 P-GSM supported 0 0 1 0 GSM 1800 supported 0 0 1 1 GSM 450 supported 0 1 0 0 GSM 480 supported 0 1 0 1 GSM 850 supported 0 1 1 0 GSM 1900 supported 0 1 1 1 GSM 750 supported 1 0 0 0 GSM 710 supported 1 0 0 1 T-GSM 810 supported |
TSPC_Type_GSM_P_Band TSPC_Type_GSM_E_Band TSPC_Type_DCS_Band TSPC_Type_GSM_450_Band TSPC_Type_GSM_480_Band TSPC_Type_PCS_Band TSPC_Type_GSM_750_Band TSPC_Type_GSM_850_Band TSPC_Type_GSM_710_Band TSPC_Type_T_GSM_810_Band |
28 |
GSM 750 Associated Radio Capability |
See the semantic rule for the sending of this field. This field indicates whether GSM 750 band is supported and its associated radio capability. The radio capability contains the binary coding of the power class associated with the GSM 750 band (see 3GPP TS 45.005 [33]). NOTE: The coding of the power class for GSM 750 in GSM 750 Associated Radio Capability is different to that used in the Mobile Station Classmark 1 and Mobile Station Classmark 2 information elements. |
TSPC_Type_GSM_750_Class2 TSPC_Type_GSM_750_Class3 TSPC_Type_GSM_750_Class4 TSPC_Type_GSM_750_Class5 |
29 |
UMTS 1.28 Mcps TDD Radio Access Technology Capability |
0 UMTS 1.28 Mcps TDD not supported |
TSPC_Type_UTRAN1.28_TDD |
30 |
GERAN Feature Package 1 |
0 GERAN feature package 1 not supported. |
TSPC_GERAN_FEATURE_PACKAGE_1 |
31 |
Extended DTM GPRS Multi Slot Class |
DGMSC Bit 2 1 Bit 2 1 0 0 0 0 Unused. If received, it shall be interpreted as ‘01 00’ 0 0 0 1 Unused. If received, it shall be interpreted as ‘01 00’ 0 0 1 0 Unused. If received, it shall be interpreted as ‘01 00’ 0 0 1 1 Unused. If received, it shall be interpreted as ‘01 00’ 0 1 0 0 Multislot class 5 supported 0 1 0 1 Multislot class 6 supported 0 1 1 0 Unused. If received, it shall be interpreted as ‘01 00’ 0 1 1 1 Unused. If received, it shall be interpreted as ‘01 00’ 1 0 0 0 Multislot class 9 supported 1 0 0 1 Multislot class 10 supported 1 0 1 0 Unused. If received, it shall be interpreted as ‘10 00’ 1 0 1 1 Unused. If received, it shall be interpreted as ‘10 00’ 1 1 0 0 Multislot class 11 supported 1 1 0 1 Unused. If received, it shall be interpreted as ’11 00’ 1 1 1 0 Unused. If received, it shall be interpreted as ’11 00’ 1 1 1 1 Unused. If received, it shall be interpreted as ’11 00’ The presence of this field indicates that the MS supports combined fullrate and halfrate GPRS channels in the downlink.When this field is not present, the MS supports the multislot class indicated by the DTM GPRS Multi Slot Class field. If this field is included, it shall contain one of the following values if the DTM GPRS High Multi Slot Class field is present:
Multislot class 11 if DTM GPRS High Multi Slot Class is set to indicate Classes 32/37, 33/38 or Classes 42, 43, 44. |
TSPC_DTM_GPRS_Multislot_Class_5 TSPC_DTM_GPRS_Multislot_Class_6 TSPC_DTM_GPRS_Multislot_Class_9 TSPC_DTM_GPRS_Multislot_Class_10 TSPC_DTM_GPRS_Multislot_Class_11 TSPC_DTM_GPRS_Multislot_Class31 Or TSPC_DTM_GPRS_Multislot_Class36 Or TSPC_DTM_GPRS_Multislot_Class41 TSPC_DTM_GPRS_Multislot_Class32 Or TSPC_DTM_GPRS_Multislot_Class37 TSPC_DTM_GPRS_Multislot_Class33 Or TSPC_DTM_GPRS_Multislot_Class38 or TSPC_DTM_GPRS_Multislot_Class42 TSPC_DTM_GPRS_Multislot_Class43 TSPC_DTM_GPRS_Multislot_Class44 |
32 |
Extended DTM EGPRS Multi Slot Class |
This field is not considered when the DTM EGPRS Multi Slot Class field is not included. This field indicates the extended DTM EGPRS multislot capabilities of the MS and shall be interpreted in conjunction with the DTM EGPRS Multi Slot Class field. This field is coded as the Extended DTM GPRS Multi Slot Class field. The presence of this field indicates that the MS supports combined fullrate and halfrate GPRS channels in the downlink. When this field is not present, the MS supports the multislot class indicated by the DTM EGPRS Multi Slot Class field. If this field is included, it shall contain one of the following values if the DTM EGPRS High Multi Slot Class field is present: – Multislot class 10 if DTM EGPRS High Multi Slot Class is set to indicate Class 31/36 or Class 41; – Multislot class 11 if DTM EGPRS High Multi Slot Class is set to indicate Classes 32/37, 33/38 or Classes 42, 43, 44. |
TSPC_DTM_EGPRS_Multislot_Class_10 TSPC_DTM_EGPRS_Multislot_Class_11 TSPC_DTM_EGPRS_Multislot_Class_31 TSPC_DTM_EGPRS_Multislot_Class_36 TSPC_DTM_EGPRS_Multislot_Class_41 TSPC_DTM_EGPRS_Multislot_Class_32 TSPC_DTM_EGPRS_Multislot_Class_37 TSPC_DTM_EGPRS_Multislot_Class_33 TSPC_DTM_EGPRS_Multislot_Class_38 TSPC_DTM_EGPRS_Multislot_Class_42 TSPC_DTM_EGPRS_Multislot_Class_43 TSPC_DTM_EGPRS_Multislot_Class_44 |
33 |
High Multislot Capability |
This field indicates the support of multislot classes 30 to 45, see 3GPP TS 45.002 [32]. The High Multislot Capability is individually combined with each multislot class field sent by the MS (the possible multislot class fields are: GPRS multislot class, EGPRS multislot class) to extend the related multislot class with the rule described in the MS Radio Access Capability IE. The same capability is applicable also to EGPRS2 if supported. |
TSPC_Type_GPRS_Multislot_Class30 to TSPC_Type_GPRS_Multislot_Class45 TSPC_Type_EGPRS_Multislot_Class30 to TSPC_Type_EGPRS_Multislot_Class45 |
34 |
GERAN Iu Mode Capabilities |
This field indicates if the mobile station supports GERAN Iu mode. Furthermore, it indicates the GERAN Iu mode capabilities of the mobile station. The field shall be included if the mobile station supports GERAN Iu mode. If the field is not present, the mobile station does not support GERAN Iu mode. |
TSPC_GERAN_IuMode_Capability |
35 |
FLO Iu Capability |
0 FLO in GERAN Iu mode not supported 1 FLO in GERAN Iu mode supported |
TSPC_FLO_Iu_Capability |
36 |
GERAN Feature Package 2 |
0 GERAN feature package 2 not supported. |
TSPC_GERAN_FEATURE_PACKAGE_2 |
37 |
Void |
||
38 |
GMSK Multislot Power Profile |
Bits 2 1 0 0 GMSK_MULTISLOT_POWER_PROFILE 0 0 1 GMSK_MULTISLOT_POWER_PROFILE 1 1 0 GMSK_MULTISLOT_POWER_PROFILE 2 1 1 GMSK_MULTISLOT_POWER_PROFILE 3 |
TSPC_Type_GMSK_Multislot_Power_Profile_0 TSPC_Type_GMSK_Multislot_Power_Profile_1 TSPC_Type_GMSK_Multislot_Power_Profile_2 TSPC_Type_GMSK_Multislot_Power_Profile_3 |
39 |
8-PSK Multislot Power Profile |
Bits 2 1 0 0 8-PSK_MULTISLOT_POWER_PROFILE 0 0 1 8-PSK_MULTISLOT_POWER_PROFILE 1 1 0 8-PSK_MULTISLOT_POWER_PROFILE 2 1 1 8-PSK_MULTISLOT_POWER_PROFILE 3 |
TSPC_Type_8-PSK_Multislot_Power_Profile_0 TSPC_Type_8-PSK_Multislot_Power_Profile_1 TSPC_Type_8-PSK_Multislot_Power_Profile_2 TSPC_Type_8-PSK_Multislot_Power_Profile_3 |
40 |
T-GSM 400 Bands Supported |
Bits |
TSPC_Type_T_GSM_380_Band TSPC_Type_T_GSM_410_Band |
41 |
T-GSM 400 Associated Radio Capability |
If either T-GSM 410 or T-GSM 380 or both is supported, the T-GSM 400 Associated Radio Capability field indicates the radio capability for T-GSM 410 and/or T-GSM 380. The radio capability contains the binary coding of the power class associated with the band indicated in T-GSM 400 Bands Supported bits (see 3GPP TS 45.005 [33]). NOTE: The coding of the power class for T-GSM 410 and T-GSM 380 in T-GSM 400 Associated Radio Capability is different to that used in the Mobile Station Classmark 1 and Mobile Station Classmark 2 information elements. |
TSPC_Type_T_GSM_400_Class2 TSPC_Type_T_GSM_400_Class3 TSPC_Type_T_GSM_400_Class4 TSPC_Type_T_GSM_400_Class5 |
42 |
T-GSM 900 Associated Radio Capability |
See the semantic rule for the sending of this field. This field indicates whether T-GSM 900 band is supported and its associated radio capability. The radio capability contains the binary coding of the power class associated with the T-GSM 900 band (see 3GPP TS 45.005 [33]). Note: the coding of the power class for T-GSM 900 in T-GSM 900 Associated Radio Capability is different to that used in the Mobile Station Classmark 1 and Mobile Station Classmark 2 information elements. |
Shall not be supported anymore |
43 |
Downlink Advanced Receiver Performance |
Bits 2 1 0 0 Downlink Advanced Receiver Performance not supported 0 1 Downlink Advanced Receiver Performance – phase I supported 1 0 Downlink Advanced Receiver Performance – phase II supported NOTE 1) |
TSPC_DARP_Phase1 TSPC_DARP_Phase2 |
44 |
DTM Enhancements Capability |
This field indicates whether the mobile station supports enhanced DTM CS establishment and enhanced DTM CS release or not. It is coded as follows: 0 The mobile station does not support enhanced DTM CS establishment and enhanced DTM CS release procedures. |
TSPC_Enhanced_DTM_CS |
45 |
DTM GPRS High Multi Slot Class |
Bit |
TSPC_DTM_GPRS_Multislot_Class_31 TSPC_DTM_GPRS_Multislot_Class_32 TSPC_DTM_GPRS_Multislot_Class_33 TSPC_DTM_GPRS_Multislot_Class_36 TSPC_DTM_GPRS_Multislot_Class_37 TSPC_DTM_GPRS_Multislot_Class_38 TSPC_DTM_GPRS_Multislot_Class_41 TSPC_DTM_GPRS_Multislot_Class_42 TSPC_DTM_GPRS_Multislot_Class_43 TSPC_DTM_GPRS_Multislot_Class_44 |
46 |
Offset required |
0 The mobile station does not require the offset |
TSPC_Offset_Required |
47 |
DTM EGPRS High Multi Slot Class |
This field indicates the DTM EGPRS multislot capabilities of the MS. This field may be included only if the mobile station supports EGPRS DTM. This field is coded as the DTM GPRS High Multi Slot Class field. When this field is not present, the MS supports the DTM multislot class indicated by the DTM EGPRS Multi Slot Class field. The values ‘0 0 1’, ‘0 1 0’ and ‘0 1 1’ shall be interpreted as indicating DTM EGPRS multislot class 36, 37 or 38 respectively if the Offset required field indicates that the Timing Advance offset t0 is required; in all other cases those codepoints shall be interpreted as indicating DTM EGPRS multislot class 31, 32 or 33 respectively. The same multislot capability is applicable also for EGPRS2 if supported |
TSPC_DTM_EGPRS_Multislot_Class_31 TSPC_DTM_EGPRS_Multislot_Class_32 TSPC_DTM_EGPRS_Multislot_Class_33 TSPC_DTM_EGPRS_Multislot_Class_36 TSPC_DTM_EGPRS_Multislot_Class_37 TSPC_DTM_EGPRS_Multislot_Class_38 |
48 |
Repeated ACCH Capability |
1 bit field This field indicates whether the MS supports Repeated SACCH and Repeated Downlink FACCH (see 3GPP TS 44.006 [76]). It is coded as follows: 0 The mobile station does not support Repeated SACCH An MS that only supports Repeated Downlink FACCH shall set this bit field to ‘0’. NOTE 1) |
TSPC_Repeated_SACCH TSPC_Repeated_FACCH |
49 |
GSM 710 Associated Radio Capability |
See the semantic rule for the sending of this field. This field indicates whether GSM 710 band is supported and its associated radio capability. The radio capability contains the binary coding of the power class associated with the GSM 710 band (see 3GPP TS 45.005 [33]). NOTE: The coding of the power class for GSM 710 in GSM 710 Associated Radio Capability is different to that used in the Mobile Station Classmark 1 and Mobile Station Classmark 2 information elements. |
TSPC_Type_GSM_710_Class2 TSPC_Type_GSM_710_Class3 TSPC_Type_GSM_710_Class4 TSPC_Type_GSM_710_Class5 |
50 |
T-GSM 810 Associated Radio Capability |
See the semantic rule for the sending of this field. This field indicates whether T- GSM 810 band is supported and its associated radio capability. The radio capability contains the binary coding of the power class associated with the T-GSM 810 band (see 3GPP TS 45.005 [33]). NOTE: The coding of the power class for T-GSM 810 in T-GSM 810 Associated Radio Capability is different to that used in the Mobile Station Classmark 1 and Mobile Station Classmark 2 information elements. |
TSPC_Type_T_GSM_810_Class2 TSPC_Type_T_GSM_810_Class3 TSPC_Type_T_GSM_810_Class4 TSPC_Type_T_GSM_810_Class5 |
51 |
Ciphering Mode Setting Capability |
0 The mobile station does not support the Ciphering Mode Setting IE in the 1 The mobile station supports the Ciphering Mode Setting IE in the DTM ASSIGNMENT COMMAND |
TSPC_Ciphering_Mode_Setting_Cap |
52 |
Additional Positioning Capabilities |
0 The mobile station does not support additional positioning capabilities which can be retrieved using RRLP |
TSPC_Additional_Positioning_Cap |
53 |
E-UTRA FDD support |
Bit 0 E-UTRA FDD not supported 1 E-UTRA FDD supported |
TSPC_Type_E-UTRA_FDD |
54 |
E-UTRA TDD support |
Bit 0 E-UTRA TDD not supported 1 E-UTRA TDD supported |
TSPC_Type_E-UTRA_TDD |
55 |
E-UTRA Measurement and Reporting support |
Bit 0 E-UTRAN Neighbour Cell measurements and measurement reporting while having an RR connection 1 E-UTRAN Neighbour Cell measurements and measurement reporting while having an RR connection |
TSPC_E-UTRA_Measurement_Reporting |
56 |
Priority Based Cell Reselection |
Bit 0 Priority-based cell reselection not supported 1 Priority-based cell reselection supported |
TSPC_Priority_Based_Cell_Reselection |
57 |
UTRA CSG Cells Reporting |
Bit 0 Reporting of UTRAN CSG cells not supported 1 Reporting of UTRAN CSG cells supported |
TSPC_UTRA_CSG_Cells_Reporting |
58 |
VAMOS Level |
Bits 2 1 0 0 VAMOS not supported 0 1 VAMOS I supported 1 0 VAMOS II supported 1 1 VAMOS III supported. (NOTE 1) |
TSPC_VAMOS_Type1 TSPC_VAMOS_Type2 TSPC_VAMOS_Type3 |
59 |
TIGHTER Capability |
Bits 2 1 0 0 TIGHTER not supported (NOTE 2) |
(TSPC_TIGHTER_SPEECH_SIGNALLING OR TSPC_TIGHTER_GPRS_EGPRS OR TSPC_TIGHTER_EGPRS2) AND TSPC_DARP_Phase1 |
60 |
Selective Ciphering of Downlink SACCH |
Bit 0 Selective Ciphering of Downlink SACCH not supported 1 Selective Ciphering of Downlink SACCH supported |
TSPC_Selective_Ciphering_DL_SACCH |
61 |
ER Band Support |
Bit 0 ER-GSM not supported 1 ER-GSM supported NOTE 3) |
TSPC_Type_ER_GSM_Band |
NOTE 1: An MS indicating support for VAMOS (Item 58) shall also indicate support for either “Downlink Advanced Receiver Performance – phase I” or “Downlink Advanced Receiver Performance – phase II” (Item 43), and for “Repeated SACCH and Repeated Downlink FACCH” (Item 48). NOTE 2: An MS indicating support for TIGHTER (Item 59) shall also indicate support for “Downlink Advanced Receiver Performance – phase I” (Item 43), ((TSPC_TIGHTER_SPEECH_SIGNALLING OR TSPC_TIGHTER_GPRS_EGPRS OR TSPC_TIGHTER_EGPRS2) AND (TSPC_DARP_Phase1)) NOTE 3: An MS indicating the support of ER-GSM shall also indicate support for R-GSM band (Item 1 and 4)( TSPC_Type_GSM_R_Band) |
26.6.11.1 Classmark change
This procedure allows the MS to indicate to the network that a change in the classmark (e.g. due to addition of power amplification) has taken place.
26.6.11.1.1 Conformance requirements
If the RF power capability of the MS is changed during a call, this change shall be signalled to the network.
If the RF power capability of the MS is changed in idle mode, the up to date RF power capability shall be signalled to the network during RR connection establishment.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.4.10.
26.6.11.1.2 Test purpose
To verify that if the RF power capability or any other capability indicated in a Classmark IE of the MS is changed during a call, the change is communicated on the DCCH to the network.
To verify that if the RF power capability or any other capability indicated in a Classmark IE of the MS is changed in idle mode, the out of date capabilities are not communicated to the network during RR connection establishment.
26.6.11.1.3 Method of test
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
The MS is in the "idle, updated" state, with a TMSI allocated and with no additional power amplification applied.
Specific PICS statements
- TSPC_Type_xxx (all appropriate power classes)
- TSPC_AddInfo_Full_rate_version_1
- TSPC_AddInfo_Full_rate_version_2
- TSPC_AddInfo_Full_rate_version_3
PIXIT statements
–
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated and with no additional power amplification applied.
Test Procedure
With the MS in idle mode, the RF power capability shall be changed by the addition of power amplification, after which the MS is made to originate a call. The new RF power capability shall be included in the CM SERVICE REQUEST message. After the call has reached the Call Control state U10, the RF power capability of the MS is changed by removal of the additional power amplification. The MS shall send a CLASSMARK CHANGE message indicating the new RF power capability. The RF power capability is then changed by adding the power amplification. The MS shall again send a CLASSMARK CHANGE message indicating the new RF power capability. The call is then released by the SS.
With the MS in idle mode, the power amplification is removed. The SS then pages the MS, which in the PAGING RESPONSE message shall indicate the correct RF power capability.
Finally the SS transmits a CHANNEL RELEASE to end the test.
Maximum Duration of Test
5 minutes, including 1 minute for any necessary operator actions.
Expected Sequence
Step |
Direction |
Message |
Comments |
1 |
——– |
——– |
Add power amplification. |
2 |
——– |
——– |
The MS shall be made to originate a call. |
3 |
MS -> SS |
CHANNEL REQUEST |
Establ. Cause = "Originating call" NECI not equal to one. |
4 |
SS -> MS |
IMMEDIATE ASSIGNMENT |
|
5 |
MS -> SS |
CM SERVICE REQUEST |
The "Mobile Station Classmark 2" IE shall indicate the new RF power capability. |
6 |
SS -> MS |
CM SERVICE ACCEPT |
|
7 |
MS -> SS |
SETUP |
|
8 |
SS -> MS |
CALL PROCEEDING |
|
9 |
SS -> MS |
ALERTING |
|
10 |
SS -> MS |
ASSIGNMENT COMMAND |
The Channel Mode is a non-signalling mode arbitrarily selected from the full rate capabilities declared for the MS |
11 |
MS -> SS |
ASSIGNMENT COMPLETE |
|
12 |
SS -> MS |
CONNECT |
|
13 |
MS -> SS |
CONNECT ACKNOWLEDGE |
|
14 |
——– |
——– |
Remove the power amplification. |
15 |
MS -> SS |
CLASSMARK CHANGE |
The "Mobile Station Classmark 2" IE shall indicate the new power capability. |
16 |
——– |
——– |
Add power amplification. |
17 |
MS -> SS |
CLASSMARK CHANGE |
The "Mobile Station Classmark 2" IE shall indicate the new power capability. |
18 |
SS -> MS |
CHANNEL RELEASE |
|
19 |
——– |
——– |
Remove the power amplification. |
——– |
——– |
The SS waits 12 s to allow the MS to perform cell reselection. |
|
20 |
SS -> MS |
PAGING REQUEST TYPE 1 |
|
21 |
MS -> SS |
CHANNEL REQUEST |
Establ. Cause = "Answer to paging". |
22 |
SS -> MS |
IMMEDIATE ASSIGNMENT |
|
23 |
MS -> SS |
PAGING RESPONSE |
The "Mobile Station Classmark 2" IE shall indicate the new power capability. |
24 |
SS -> MS |
CHANNEL RELEASE |
Specific Message Contents
None.
26.6.11.2 Classmark interrogation
This procedure allows the network to request the MS to supply all its classmark information to the network.
Networks may systematically use this procedure (e.g. during location updating) and, it if is incorrectly implemented in the MS, the basic connection establishment procedure may systematically fail.
26.6.11.2.1 Conformance requirements
On receipt of a CLASSMARK ENQUIRY message, the MS sends a CLASSMARK CHANGE message to the network containing the Mobile Station Classmark 2 information element and depending upon the contents of this information element, possibly the Mobile Station Classmark 3 information element.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.4.11 and 9.1.11.1.
3GPP TS 04.13 subclause 5.2.9.
26.6.11.2.2 Test purpose
To verify that if the network requests the MS to supply all its classmark information then this information is communicated on the DCCH to the network.
26.6.11.2.3 Method of test
Initial Conditions
System Simulator:
1 cell, default parameters.
Mobile Station:
"Idle, updated", with TMSI allocated.
Specific PICS statements
–
PIXIT statements
–
Foreseen Final State of the MS
"Idle, updated", with TMSI allocated.
Test Procedure
The MS is switched off (or has its power removed).
The SS then sets the IMSI attach-detach flag in the SYSTEM INFORMATION messages so that the MS shall perform a location update when switched on.
The MS is switched on (or its power is re-applied). The MS then initiates a location update attempt. After the mobile has sent the LOCATION UPDATING REQUEST message, the SS transmits a CLASSMARK ENQUIRY message. The MS shall be ready to transmit the CLASSMARK CHANGE message before 300 ms after the end of the CLASSMARK ENQUIRY message. The contents of the Mobile Station Classmark 2 Information element and the contents of Mobile Station Classmark 3 information element is recorded and compared to the corresponding PICS/PIXIT statement as shown in table 26.6.11a and 26.6.11b.
The term "ready to transmit" is defined in 3GPP TS 04.13.
Then the SS transmits a LOCATION UPDATING ACCEPT message that does not contain a Mobile Identity IE.
Maximum Duration of Test
2 minutes.
Expected Sequence
Step |
Direction |
Message |
Comments |
1 |
MS |
The MS is switched off (or has its power removed). |
|
2 |
SS |
IMSI attach-detach flag changed. |
|
3 |
MS |
The MS is switched on (or its power is re-applied). |
|
4 |
MS -> SS |
CHANNEL REQUEST |
|
5 |
SS -> MS |
IMMEDIATE ASSIGNMENT |
|
6 |
MS -> SS |
LOCATION UPDATING REQUEST |
|
7 |
SS -> MS |
CLASSMARK ENQUIRY |
|
8 |
MS -> SS |
CLASSMARK CHANGE |
This message shall be ready to be transmitted before 300 ms after the completion of step 7. SS compares the contents of the Mobile Station Classmark 2/3 Information elements to the corresponding PICS/PIXIT statements. |
9 |
SS -> MS |
LOCATION UPDATING ACCEPT |
|
10 |
SS -> MS |
CHANNEL RELEASE |
Specific Message Contents
Contents of LOCATION UPDATING ACCEPT message:
Protocol Discriminator |
MM message |
Skip Indicator |
0000 |
Message Type |
00000010 |
Location Area Identification |
|
– Mobile Country Code |
001 decimal |
– Mobile Network Code |
01 decimal (PCS 1 900: 011 decimal) |
– Location Area Code |
0001H |
Mobile Identity |
Not present |
Follow on proceed |
Not present |
26.6.11.3 Classmark interrogation / UTRAN Classmark Change
This procedure allows the network to request the MS to supply all its classmark information to the network. In addition the network may request a MS supporting UTRAN to send the UTRAN classmark information.
Networks may systematically use this procedure (e.g. during location updating) and, it if is incorrectly implemented in the MS, the basic connection establishment procedure may systematically fail.
If the last timeslot of the message block containing a CLASSMARK ENQUIRY message occurs at time T, then the MS shall be ready to transmit the CLASSMARK CHANGE message before T + 300 ms.
26.6.11.3.1 Conformance requirements
On receipt of a CLASSMARK ENQUIRY message, the MS sends a CLASSMARK CHANGE message to the network containing the Mobile Station Classmark 2 information element and depending upon the contents of this information element, possibly the Mobile Station Classmark 3 information element.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.4.11 and 9.1.11.1.
3GPP TS 04.13 subclause 5.2.9.
26.6.11.3.2 Test purpose
To verify that if the network requests the MS to supply all its classmark information, including the UTRA Classmark information, then this information is communicated on the DCCH to the network.
26.6.11.3.3 Method of test
Initial Conditions
System Simulator:
1 cell, default parameters. In SI3 is ATT flag is set to 1 and Early Classmark Sending Control flag is set to Low.
Mobile Station:
Powered off.
Specific PICS statements
–
PIXIT statements
Test Procedure
The MS is switched on (or its power is re-applied). The MS then initiates a location update attempt. After the mobile has sent the LOCATION UPDATING REQUEST message, the SS transmits a CLASSMARK ENQUIRY message. The MS shall be ready to transmit the CLASSMARK CHANGE message within 300 ms after the end of the CLASSMARK ENQUIRY message. The contents of the Mobile Station Classmark 2 Information element and the contents of Mobile Station Classmark 3 information element are compared to the corresponding PICS/PIXIT statements as shown in table 26.6.11a and 26.6.11b.
The term "ready to transmit" is defined in 3GPP TS 04.13.
Then the SS transmits a LOCATION UPDATING ACCEPT message that does not contain a Mobile Identity IE.
Maximum Duration of Test
2 minutes.
Expected Sequence
Step |
Direction |
Message |
Comments |
1 |
MS |
The MS is switched on. |
|
2 |
MS -> SS |
CHANNEL REQUEST |
|
3 |
SS -> MS |
IMMEDIATE ASSIGNMENT |
|
4 |
MS -> SS |
LOCATION UPDATING REQUEST |
|
5 |
SS -> MS |
CLASSMARK ENQUIRY |
|
6 |
MS -> SS |
CLASSMARK CHANGE |
This message shall be ready transmitted within 300 ms after the completion of step 5. If MS support UMTS FDD: UMTS FDD Radio Access Capability = 1 If MS support UMTS TDD: UMTS TDD Radio Access Capability = 1 Contents as declared in PICS/ PIXIT. |
7 |
MS -> SS |
UTRAN Classmark Change |
Contents as declared in PIXIT. |
8 |
SS -> MS |
LOCATION UPDATING ACCEPT |
|
9 |
SS -> MS |
CHANNEL RELEASE |
Specific Message Contents
Content of CLASSMARK ENQUIRY message:
Protocol Discriminator |
RR management |
Skip Indicator |
0000 |
Message Type |
00010011 |
Classmark Enquiry Mask value part |
00001100, note |
Note CLASSMARK CHANGE message is requested; UTRAN CLASSMARK CHANGE message is requested; CDMA2000 CLASSMARK CHANGE message not requested; and GERAN IU MODE CLASSMARK CHANGE message not requested. |
Contents of LOCATION UPDATING ACCEPT message:
Protocol Discriminator |
MM message |
Skip Indicator |
0000 |
Message Type |
00000010 |
Location Area Identification |
|
– Mobile Country Code |
001 decimal |
– Mobile Network Code |
01 decimal (PCS 1 900: 011 decimal) |
– Location Area Code |
0001H |
Mobile Identity |
Not present |
Follow on proceed |
Not present |
26.6.11.4 Early UTRAN Classmark Sending
This procedure allows the network to request the MS to supply all its classmark information to the network. In addition the network may request a MS supporting UTRAN to send the UTRAN classmark information.
Networks may systematically use this procedure (e.g. during location updating) and, it if is incorrectly implemented in the MS, the basic connection establishment procedure may systematically fail.
26.6.11.4.1 Conformance requirements
Early classmark sending consists in the mobile station sending as early as possible after access a CLASSMARK CHANGE message to provide the network with additional classmark information. In addition a MS supporting UTRAN sends a UTRAN Classmark Change message; an MS supporting CDMA2000 sends a CDMA2000 Classmark Change. When a CLASSMARK CHANGE message and one or more additional UTRAN Classmark Change or CDMA2000 Classmark Change messages are to be sent, the CLASSMARK CHANGE message shall be sent first.
….
A mobile station which implements the support of one or more 3G Radio Access Technology shall also implement the « Controlled Early Classmark Sending » option; in this case neither UTRAN CLASSMARK CHANGE nor CDMA2000 CLASSMARK CHANGE message shall be sent by the mobile if prohibited by the 3G Early Classmark Sending Restriction parameter in the last reception in the accessed cell of the SYSTEM INFORMATION TYPE 3 message or the PACKET SYSTEM INFORMATION TYPE 2 message (see 3GPP TS 04.60). If the PACKET SYSTEM INFORMATION TYPE 2 messages have been received, but the 3G Early Classmark Sending Restriction flag is not included, the mobile station shall assume neither UTRAN nor cdma2000 classmark change message shall be sent with the Early Classmark Sending.
During a contention resolution procedure, if the last timeslot of the block containing a Layer 2 UA frame, occurs at time T, then the MS shall be ready to transmit the CLASSMARK CHANGE message, if applicable (see GSM 04.06 [3] and GSM 04.08 [4]), before T + 40 ms.
References
3GPP TS 04.08 / 3GPP TS 44.018 subclauses 3.3.1.1.4.1 and 9.1.11.1.
3GPP TS 04.13 subclause 5.2.9.
26.6.11.4.2 Test purpose
To verify that if the network requests the MS to supply all its classmark information, including the UTRAN Classmark information, then this information is communicated on the DCCH to the network. The request of the classmark information is indicated in SYSTEM INFORMATION TYPE 3.
26.6.11.4.3 Method of test
Initial Conditions
System Simulator:
1 cell, default parameters.
The SS shall transmit SI3 with ATT flag is set to 1 and both Early Classmark Sending Restriction and 3G Early Classmark Sending Restriction parameter set to High.
Mobile Station:
Powered off.
Specific PICS statements
–
PIXIT statements
- Contents of Mobile Station Classmark 2 information element
- Contents of Mobile Station Classmark 3 information element
- Contents of UTRAN Classmark Change information
Test Procedure
The MS is switched on (or its power is re-applied). The MS then initiates a location update attempt. After the mobile has sent the LOCATION UPDATING REQUEST message, the MS transmits the CLASSMARK CHANGE and UTRAN CLASSMARK CHANGE messages.
Then the SS transmits a LOCATION UPDATING ACCEPT message that does not contain a Mobile Identity IE.
Maximum Duration of Test
2 minutes.
Expected Sequence
Step |
Direction |
Message |
Comments |
1 |
MS |
The MS is switched on. |
|
2 |
MS -> SS |
CHANNEL REQUEST |
|
3 |
SS -> MS |
IMMEDIATE ASSIGNMENT |
|
4 |
MS -> SS |
LOCATION UPDATING REQUEST |
(SABM) |
5 |
SS -> MS |
LOCATION UPDATING REQUEST |
(UA) |
6 |
MS -> SS |
CLASSMARK CHANGE |
This message shall be transmitted within 69 ms after the completion of step 5. If MS support UMTS FDD: UMTS FDD Radio Access Capability = 1 If MS support UMTS TDD: UMTS TDD Radio Access Capability = 1 Contents as declared in PIXIT. |
7 |
MS -> SS |
UTRAN CLASSMARK CHANGE |
Contents as declared in PIXIT. |
8 |
SS -> MS |
LOCATION UPDATING ACCEPT |
|
9 |
SS -> MS |
CHANNEL RELEASE |
Specific Message Contents
Contents of LOCATION UPDATING ACCEPT message:
Protocol Discriminator |
MM message |
Skip Indicator |
0000 |
Message Type |
00000010 |
Location Area Identification |
|
– Mobile Country Code |
001 decimal |
– Mobile Network Code |
01 decimal (PCS 1 900: 011 decimal) |
– Location Area Code |
0001H |
Mobile Identity |
Not present |
Follow on proceed |
Not present |