26.11.5 Multiband signalling / Structured procedures

3GPP51.010-1Mobile Station (MS) conformance specificationPart 1: Conformance specificationTS

These tests applies only to multiband mobile stations.

26.11.5.1 Multiband signalling / Structured procedures / MS originated call / early assignment

26.11.5.1.1 Conformance requirements

1) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call, if it provides a human interface, shall display the dialled number.

2) An MS in MM state "idle, updated" and in RR idle mode, when made to initiate a call for a selected teleservice that is supported by the MS, shall start to initiate the immediate assignment procedure by sending a CHANNEL REQUEST message with correct establishment cause.

3) After the initial message the multiband MS shall send a CLASSMARK CHANGE message in the uplink block followed direct after the Layer 2 UA message sent from the network. The CLASSMARK CHANGE message shall contain information elements Mobile Station Classmark 2 and Mobile Station Classmark 3.

4) Subsequently after establishment of an MM connection, the MS shall send a SETUP message with correct parameters.

5) The call control entity of the Mobile Station in the "call initiated" state, in the "mobile originating call proceeding" state or in the "call delivered" state, shall, upon receipt of a CONNECT message:

– attach the user connection to the radio path;

– return a CONNECT ACKNOWLEDGE message.

6) Subsequently when the network initiates call clearing by sending a DISCONNECT message, the MS shall proceed to release the call by sending a RELEASE message.

7) On receipt of a CHANNEL RELEASE message, the MS shall disconnect the main signalling link.

References

Conformance requirement 1: 3GPP TS 02.07.

Conformance requirement 2: 3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.3.1.1.

Conformance requirement 3: 3GPP TS 04.08 / 3GPP TS 44.018 subclause 3.3.1.1.4.

Conformance requirement 4: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.2.1.1.

Conformance requirement 5: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.2.1.6.

Conformance requirement 6: 3GPP TS 04.08 / 3GPP TS 24.008 subclause 5.4.4.

Conformance requirement 7: 3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.4.13.1.

26.11.5.1.2 Test purpose

1) To verify that the MS in MM state "idle, updated" with a TMSI assigned, when made to initiate a call for a selected teleservice that is supported by the MS as declared in a PICS/PIXIT statement, displays the dialled number in the way described in a PICS/PIXIT statement.

2) To verify that the MS in MM state "idle, updated" and in RR idle mode, with a TMSI assigned, when made to initiate a call for a selected teleservice that is supported by the MS as declared in a PICS/PIXIT statement, starts to initiate an immediate assignment procedure by sending the CHANNEL REQUEST message with correct establishment cause.

3) To verify that a multiband MS is able to send an early CLASSMARK CHANGE on the DCCH uplink.

4) To verify that subsequently after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after completion of establishment of the main signalling link, after having sent a CM SERVICE REQUEST message, after having successfully performed the authentication and cipher mode setting procedures, the MS sends a SETUP message with correct parameters.

5) To verify that subsequently, after receipt of a CALL PROCEEDING message and of an HANDOVER COMMAND message allocating an appropriate TCH in another band, after having completed the traffic channel early assignment procedure by replying with the HANDOVER COMPLETE message, after receipt of an ALERTING message and a CONNECT message, the MS returns a CONNECT ACKNOWLEDGE message.

To verify that subsequently the MS has attached the user connection to the radio path. (This is checked by verifying that there is a point in time after transmission of the first L2 frame containing the (complete) CONNECT message, where the MS is sending appropriate speech or data frames whenever it does not have to transmit or acknowledge an I frame on layer 2 of the FACCH.)

6) To verify that subsequently upon the network initiating call clearing by sending a DISCONNECT message, the MS proceed to release the call with RELEASE.

7) To verify that subsequently, on receipt of a RELEASE COMPLETE message followed by a CHANNEL RELEASE message, the MS disconnects the main signalling link.

26.11.5.1.3 Method of test

Initial Conditions

System Simulator:

For 450/900 MS:

2 cells, A and B, with same LAI.

Cell A is a GSM 450 cell with default parameters.

Cell B is a GSM 900 cell with default parameters.

For 480/900 MS:

2 cells, A and B, with same LAI.

Cell A is a GSM 480 cell with default parameters.

Cell B is a GSM 900 cell with default parameters.

For 450/1800 MS:

2 cells, A and B, with same LAI.

Cell A is a GSM 450 cell with default parameters.

Cell B is a DCS 1 800 cell with default parameters.

For 480/1800 MS:

2 cells, A and B, with same LAI.

Cell A is a GSM 480 cell with default parameters.

Cell B is a DCS 1 800 cell with default parameters.

For 900/1 800 MS:

2 cells, A and B, with same LAI.

Cell A is a GSM 900 cell with default parameters.

Cell B is a DCS 1 800 cell with default parameters.

For 710/1900 MS, 750/1900 MS:

2 cells, A and B, with same LAI.

Cell A is a GSM 710 or GSM 750 cell with default parameters.

Cell B is a PCS 1 900 cell with default parameters.

For 850/1900 MS:

2 cells, A and B, with same LAI.

Cell A is a GSM 850 cell with default parameters.

Cell B is a PCS 1 900 cell with default parameters.

Mobile Station:

The MS is in MM-state idle, updated on cell A with valid TMSI.

Specific PICS statements:

– GSM 450 Band (TSPC_Type_GSM_450_Band)

– Standard GSM Band (P-GSM) (TSPC_Type_GSM_P_Band)

– Extended GSM Band (E-GSM) (TSPC_Type_GSM_E_Band)

– GSM 480 Band (TSPC_Type_GSM_480_Band)

– DCS 1800 band (TSPC_Type_DCS_Band)

– GSM 750 band (TSPC_Type_GSM_750_Band)

– GSM 710 band (TSPC_Type_GSM_710_Band)

PIXIT statements:

– Way to indicate mobile originated alerting.

-. Way to display the called number

Foreseen Final State of the MS

The MS is in MM-state idle, updated on cell B with valid TMSI.

Test procedure

The following test is performed for one teleservice supported by the MS:

– A teleservice is selected that is supported by the MS; if the MS supports speech, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.

– The MS is made to initiate a call on any frequency band supported by the MS. The call is established with early assignment. Having reached the active state, the call is cleared by the SS.

Maximum Duration of Test

1 minute.

Expected Sequence

Step

Direction

Message

Comments

1

MS

The "called number" is entered

2

MS -> SS

CHANNEL REQUEST

Establishment cause is "originating call and the network does not set the NECI bit to 1".

3

SS -> MS

IMMEDIATE ASSIGNMENT

4

MS -> SS

CM SERVICE REQUEST

Message is contained in SABM. Indicating early sending of CLASSMARK CHANGE

5

SS -> MS

UA (CM SERVICE REQUEST)

6

MS -> SS

CLASSMARK CHANGE

Indicating the frequency and power capability of the MS

7

SS -> MS

AUTHENTICATION REQUEST

8

MS -> SS

AUTHENTICATION RESP

SRES specifies correct value.

9

SS -> MS

CIPHERING MODE COMMAND

SS starts deciphering after sending the message.

10

MS -> SS

CIPHERING MODE COMPLETE

Shall be sent enciphered. All following messages shall be sent enciphered.

11

SS

SS starts ciphering.

12

MS -> SS

SETUP

13

SS -> MS

CALL PROCEEDING

14

SS -> MS

HANDOVER COMMAND

See specific message contents below.

15

MS -> SS

HANDOVER ACCESS

May or may not be sent. The sending of the

MS -> SS

HANDOVER ACCESS

HANDOVER ACCESS is optional as indicated in

MS -> SS

HANDOVER ACCESS

HANDOVER COMMAND.

MS -> SS

HANDOVER ACCESS

Handover Reference is included in the HANDOVER COMMAND.

Before completion of the 4 access bursts on the new DCCH, additional access bursts may also be sent on the SACCH

16

MS -> SS

SABM

Sent without information field

17

SS -> MS

UA

18

MS -> SS

HANDOVER COMPLETE

19

SS -> MS

ALERTING

20

MS

Depending on the PIXIT, an alerting indication is given

21

SS -> MS

CONNECT

22

MS -> SS

CONNECT ACKNOWLEDGE

23

MS

The appropriate bearer channel is through connected in both directions.

24

SS -> MS

DISCONNECT

25

MS -> SS

RELEASE

26

SS -> MS

RELEASE COMPLETE

27

SS -> MS

CHANNEL RELEASE

The main signalling link is released.

Specific Message Contents:

For 450/900 MS:

CM SERVICE REQUEST

as default except:

Information element

Value/remark

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

CLASSMARK CHANGE

as default except:

Information element

Value/remark

Protocol Discriminator

RR management

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

Additional MS Classmark information

– Band 1 (P-GSM) supported

According to PICS statement

– Band 2 (E-GSM) supported

According to PICS statement

– R-Band (R-GSM) supported

According to PICS statement

– ER-Band (ER-GSM) supported

According to PICS statement

– GSM 400 Band supported

According to PICS statement

– GSM 400 Associated radio capability

Corresponding to GSM 450 band

– Associated radio capability 1

Corresponding to GSM 900 band

– R-Band Associated radio capability

Corresponding to R-GSM 900 band

HANDOVER COMMAND

Information element

Value/remark

Protocol Discriminator

RR management

Cell Description

– NCC

1

– BCC

5

– BCCH Carrier Number

20

Channel description

– Channel type

TCH/F + ACCH’s

– Timeslot number

Arbitrary value

– Training sequence code

Chosen arbitrarily

– Hopping

Single RF channel

– ARFCN

50

Handover Reference

Chosen arbitrarily from the range (0,1…255)

Power Command & Access type

– Power level

Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.

– Access type control

Sending of HANDOVER ACCESS is optional

Synchronization Indication

pre-synchronized; ROT=0; NCI=0.

Timing Advance

same as in IMMEDIATE ASSIGNMENT

Mode of the First Channel

appropriate for the selected bearer service

For 480/900 MS:

CM SERVICE REQUEST

as default except:

Information element

Value/remark

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

CLASSMARK CHANGE

as default except:

Information element

Value/remark

Protocol Discriminator

RR management

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

Additional MS Classmark information

– Band 1 (P-GSM) supported

According to PICS statement

– Band 2 (E-GSM) supported

According to PICS statement

– GSM 400 Band supported

According to PICS statement

– R-Band (R-GSM) supported

According to PICS statement

– ER-Band (ER-GSM) supported

According to PICS statement

– GSM 400 Associated radio capability

Corresponding to GSM 400 band

– Associated radio capability 1

Corresponding to GSM 900 band

– R-Band Associated radio capability

Corresponding to R-GSM 900 band

HANDOVER COMMAND

Information element

Value/remark

Protocol Discriminator

RR management

Cell Description

– NCC

1

– BCC

5

– BCCH Carrier Number

20

Channel description

– Channel type

TCH/F + ACCH’s

– Timeslot number

Arbitrary value

– Training sequence code

Chosen arbitrarily

– Hopping

Single RF channel

– ARFCN

50

Handover Reference

Chosen arbitrarily from the range (0,1…255)

Power Command & Access type

– Power level

Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.

– Access type control

Sending of HANDOVER ACCESS is optional

Synchronization Indication

pre-synchronized; ROT=0; NCI=0.

Timing Advance

same as in IMMEDIATE ASSIGNMENT

Mode of the First Channel

appropriate for the selected bearer service

For 450/1 800 MS:

CM SERVICE REQUEST

as default except:

Information element

Value/remark

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

CLASSMARK CHANGE

as default except:

Information element

Value/remark

Protocol Discriminator

RR management

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

Additional MS Classmark information

– Band 3 (DCS 1 800) supported

According to PICS statement

– GSM 400 Band supported

According to PICS statement

– GSM 400 Associated radio capability

Corresponding to GSM 450 band

– Associated radio capability 2

Corresponding to DCS 1 800 band

HANDOVER COMMAND

Information element

Value/remark

Protocol Discriminator

RR management

Cell Description

– NCC

1

– BCC

5

– BCCH Carrier Number

590

Channel description

– Channel type

TCH/F + ACCH’s

– Timeslot number

Arbitrary value

– Training sequence code

Chosen arbitrarily

– Hopping

Single RF channel

– ARFCN

650

Handover Reference

Chosen arbitrarily from the range (0,1…255)

Power Command & Access type

– Power level

Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.

– Access type control

Sending of HANDOVER ACCESS is optional

Synchronization Indication

pre-synchronized; ROT=0; NCI=0.

Timing Advance

same as in IMMEDIATE ASSIGNMENT

Mode of the First Channel

appropriate for the selected bearer service

For 480/1 800 MS:

CM SERVICE REQUEST

as default except:

Information element

Value/remark

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

CLASSMARK CHANGE

as default except:

Information element

Value/remark

Protocol Discriminator

RR management

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

Additional MS Classmark information

– Band 3 (DCS 1 800) supported

According to PICS statement

– GSM 400 Band supported

According to PICS statement

– GSM 400 Associated radio capability

Corresponding to GSM 480 band

– Associated radio capability 2

Corresponding to DCS 1 800 band

HANDOVER COMMAND

Information element

Value/remark

Protocol Discriminator

RR management

Cell Description

– NCC

1

– BCC

5

– BCCH Carrier Number

590

Channel description

– Channel type

TCH/F + ACCH’s

– Timeslot number

Arbitrary value

– Training sequence code

Chosen arbitrarily

– Hopping

Single RF channel

– ARFCN

650

Handover Reference

Chosen arbitrarily from the range (0,1…255)

Power Command & Access type

– Power level

Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.

– Access type control

Sending of HANDOVER ACCESS is optional

Synchronization Indication

pre-synchronized; ROT=0; NCI=0.

Timing Advance

same as in IMMEDIATE ASSIGNMENT

Mode of the First Channel

appropriate for the selected bearer service

For 900/1 800 MS:

CM SERVICE REQUEST

as default except:

Information element

Value/remark

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

CLASSMARK CHANGE

as default except:

Information element

Value/remark

Protocol Discriminator

RR management

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

Additional MS Classmark information

– Band 1 (P-GSM) supported

According to PICS statement

– Band 2 (E-GSM) supported

According to PICS statement

– Band 3 (DCS 1 800) supported

According to PICS statement

– R-Band (R-GSM) supported

According to PICS statement

– ER-Band (ER-GSM) supported

According to PICS statement

– Associated radio capability 1

Corresponding to GSM 900 band

– Associated radio capability 2

Corresponding to DCS 1 800 band

– R-Band Associated radio capability

Corresponding to R-GSM 900 band

HANDOVER COMMAND

Information element

Value/remark

Protocol Discriminator

RR management

Cell Description

– NCC

1

– BCC

5

– BCCH Carrier Number

590

Channel description

– Channel type

TCH/F + ACCH’s

– Timeslot number

Arbitrary value

– Training sequence code

Chosen arbitrarily

– Hopping

Single RF channel

– ARFCN

650

Handover Reference

Chosen arbitrarily from the range (0,1…255)

Power Command & Access type

– Power level

Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.

– Access type control

Sending of HANDOVER ACCESS is optional

Synchronization Indication

pre-synchronized; ROT=0; NCI=0.

Timing Advance

same as in IMMEDIATE ASSIGNMENT

Mode of the First Channel

appropriate for the selected bearer service

For 710/1 900 MS, 750/1 900 MS:

CM SERVICE REQUEST

as default except:

Information element

Value/remark

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

CLASSMARK CHANGE

as default except:

Information element

Value/remark

Protocol Discriminator

RR management

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

Additional MS Classmark information

– GSM 710 Associated radio capability

Corresponding to GSM 710 band

– GSM 750 Associated radio capability

Corresponding to GSM 750 band

– PCS 1 900 Associated radio capability

Corresponding to PCS 1 900 band

HANDOVER COMMAND

Information element

Value/remark

Protocol Discriminator

RR management

Cell Description

– NCC

1

– BCC

5

– BCCH Carrier Number

590

Channel description

– Channel type

TCH/F + ACCH’s

– Timeslot number

Arbitrary value

– Training sequence code

Chosen arbitrarily

– Hopping

Single RF channel

– ARFCN

650

Handover Reference

Chosen arbitrarily from the range (0,1…255)

Power Command & Access type

– Power level

Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.

– Access type control

Sending of HANDOVER ACCESS is optional

Synchronization Indication

pre-synchronized; ROT=0; NCI=0.

Timing Advance

same as in IMMEDIATE ASSIGNMENT

Mode of the First Channel

appropriate for the selected bearer service

For 850/1 900 MS:

CM SERVICE REQUEST

as default except:

Information element

Value/remark

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

CLASSMARK CHANGE

as default except:

Information element

Value/remark

Protocol Discriminator

RR management

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

Additional MS Classmark information

– GSM 850 Associated radio capability

Corresponding to GSM 850

– PCS 1 900 Associated radio capability

Corresponding to PCS 1 900 band

HANDOVER COMMAND

Information element

Value/remark

Protocol Discriminator

RR management

Cell Description

– NCC

1

– BCC

5

– BCCH Carrier Number

590

Channel description

– Channel type

TCH/F + ACCH’s

– Timeslot number

Arbitrary value

– Training sequence code

Chosen arbitrarily

– Hopping

Single RF channel

– ARFCN

650

Handover Reference

Chosen arbitrarily from the range (0,1…255)

Power Command & Access type

– Power level

Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.

– Access type control

Sending of HANDOVER ACCESS is optional

Synchronization Indication

pre-synchronized; ROT=0; NCI=0.

Timing Advance

same as in IMMEDIATE ASSIGNMENT

Mode of the First Channel

appropriate for the selected bearer service

26.11.5.2 Structured procedures / MS terminated call / late assignment

26.11.5.2.1 Conformance requirement

1) After the initial message the multiband MS shall send a CLASSMARK CHANGE message in the uplink block followed direct after Layer 2 UA message sent from the network.

2) The MS shall acknowledge the SETUP message with a CALL CONFIRMED message, if compatibility checking was successful, the MS is not busy, and the user does not refuse the call.

3) The MS on acceptance of the call sends a CONNECT, otherwise user alerting is initiated.

4) The MS indicates acceptance of a call by sending a CONNECT message.

5) HANDOVER COMMAND is answered by HANDOVER COMPLETE.

6) For speech calls:

The mobile station shall attach the user connection at latest when sending the connect message, except if there is no compatible radio resource available at this time. In this case the attachment shall be delayed until such a resource becomes available.

For data calls:

The mobile station shall attach the user connection when receiving the CONNECT ACKNOWLEDGE message from the network.

Requirement reference:

Conformance requirement 1: 3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.3.1.1.4.

Conformance requirements 2, 3, 4: 3GPP TS 04.08 / 3GPP TS 24.008, subclauses 5.2.2.3.1, 5.2.2.3.2 and 5.2.2.5.

Conformance requirement 5: 3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.4.4.3.

Conformance requirement 6: 3GPP TS 04.08 / 3GPP TS 24.008, subclause 5.2.2.9.

26.11.5.2.2 Test purpose

1) To verify that a multiband MS is able to send an early CLASSMARK CHANGE message on the DCCH uplink.

2) To verify that the MS in "Idle, Updated" state with a TMSI assigned, after being paged by the network on the correct paging subchannel, after initiating the immediate assignment procedure by sending the CHANNEL REQUEST message, after receipt of an IMMEDIATE ASSIGNMENT message allocating an SDCCH, after having established the main signalling link, after having sent a PAGING RESPONSE message, after having performed successful authentication and cipher mode setting procedures, after receipt of a SETUP message containing a signal information element, returns a CALL CONFIRMED message followed by:

– an ALERTING message;

– or a CONNECT message.

3) To verify that in the situation of test purpose 1, if the MS sends an ALERTING message, the MS generates an alerting indication in the way described in a PIXIT statement.

4) To verify that subsequently the MS, if it had not yet sent a CONNECT message, upon acceptance of the call, sends a CONNECT message.

5) To verify that subsequently after receipt of an HANDOVER COMMAND ALLOCATING A tch IN another band, the MS sends an HANDOVER COMPLETE message.

6) To verify that subsequently the MS:

– if the call is a speech call: after sending the HANDOVER COMPLETE message has through connected the TCH in both directions (this is checked by verifying that after transmission of the first L2 frame containing the (complete) HANDOVER COMPLETE message, the MS is sending appropriate speech or data frames whenever it does not have to transmit or acknowledge an I frame on layer 2 of the FACCH).

– if the call is a data call: after receipt of a subsequent CONNECT ACKNOWLEDGE message through connects the TCH in both directions (this is checked by verifying that there is a point in time after transmission of the first L2 frame containing the (complete) CONNECT ACKNOWLEDGE message, where the MS is sending appropriate speech or data frames whenever it does not have to transmit or acknowledge an I frame on layer 2 of the FACCH).

26.11.5.2.3 Method of test

Initial Conditions

System Simulator:

For 450/900 MS:

2 cells, A and B, with same LAI.

Cell A is a GSM 450 cell with default parameters.

Cell B is a GSM 900 cell with default parameters.

For 480/900 MS:

2 cells, A and B, with same LAI.

Cell A is a GSM 480 cell with default parameters.

Cell B is a GSM 900 cell with default parameters.

For 450/1 800 MS:

2 cells, A and B, with same LAI.

Cell A is a GSM 450 cell with default parameters.

Cell B is a DCS 1 800 cell with default parameters.

For 480/1 800 MS:

2 cells, A and B, with same LAI.

Cell A is a GSM 480 cell with default parameters.

Cell B is a DCS 1 800 cell with default parameters.

For 900/1 800 MS:

2 cells, A and B, with same LAI.

Cell A is a GSM 900 cell with default parameters.

Cell B is a DCS 1 800 cell with default parameters.

For 710/1 900 MS, 750/1 900 MS:

2 cells, A and B, with same LAI.

Cell A is a GSM 710 or GSM 750 cell with default parameters.

Cell B is a PCS 1 900 cell with default parameters.

For 850/1 900 MS:

2 cells, A and B, with same LAI.

Cell A is a GSM 850 cell with default parameters.

Cell B is a PCS 1 900 cell with default parameters.

Mobile Station:

The MS is in MM-state idle, updated on cell A with valid TMSI.

Specific PICS statements:

– GSM 450 Band (TSPC_Type_GSM_450_Band)

– Standard GSM Band (P-GSM) (TSPC_Type_GSM_P_Band)

– Extended GSM Band (E-GSM) (TSPC_Type_GSM_E_Band)

– GSM 480 Band (TSPC_Type_GSM_480_Band)

– DCS 1800 band (TSPC_Type_DCS_Band)

– GSM 750 band (TSPC_Type_GSM_750_Band)

– GSM 710 band (TSPC_Type_GSM_710_Band)

PIXIT statements:

– Way to indicate mobile originated alerting.

-. Way to display the called number

Foreseen Final State of the MS

The MS is in MM-state idle, updated on cell B with valid TMSI.

Test procedure

A teleservice is selected that is supported by the MS; if the MS supports speech, the selected teleservice is speech. If necessary, the MS is configured for that teleservice.

The MS is paged on any frequency band supported by the MS and a MT call is established with late assignment (after CONNECT). The release of the call is initiated by the MS.

Maximum Duration of Test

40 s.

Expected Sequence

Step

Direction

Message

Comments

1

SS -> MS

PAGING REQUEST TYPE 1

Sent on the correct paging subchannel

2

MS -> SS

CHANNEL REQUEST

Establishment cause indicates "answer to paging".

3

SS -> MS

IMMEDIATE ASSIGNMENT

4

MS -> SS

PAGING RESPONSE

Message is contained in SABM.

5

SS -> MS

UA (PAGING RESPONSE)

6

MS -> SS

CLASSMARK CHANGE

Indicating the frequency and power capability of the MS

7

SS -> MS

AUTHENTICATION REQUEST

8

MS -> SS

AUTHENTICATION RESP

SRES specifies correct value.

9

SS -> MS

CIPHERING MODE COMMAND

SS starts deciphering after sending the message.

10

MS -> SS

CIPHERING MODE COMPLETE

Shall be sent enciphered. All following messages shall be sent enciphered.

11

SS

SS starts ciphering.

12

SS -> MS

SETUP

Message contains the signal IE.

13

MS -> SS

CALL CONFIRMED

A14

MS -> SS

CONNECT

B14

MS -> SS

ALERTING

B15

MS

An alerting indication as defined in an PIXIT statement is given by the MS.

B16

MS

The MS is made to accept the call in the way described in a PIXIT statement.

B18

MS -> SS

CONNECT

19

SS -> MS

HANDOVER COMMAND

See specific message contents below.

20

MS -> SS

HANDOVER ACCESS

Handover Reference is included in the

21

MS -> SS

HANDOVER ACCESS

HANDOVER COMMAND.

22

MS -> SS

HANDOVER ACCESS

23

MS -> SS

HANDOVER ACCESS

Before completion of the 4 access bursts on the new DCCH, additional access bursts may also be sent on the SACCH

24

MS -> SS

SABM

Sent without information field

25

SS -> MS

UA

26

MS -> SS

HANDOVER COMPLETE

27

MS

If the call is a speech call, the TCH shall be through connected in both directions.

28

SS -> MS

CONNECT ACKNOWLEDGE

29

MS

If the call is a data call, the MS shall through connect the TCH in both directions

30

MS

The MS is made to release the call.

31

MS -> SS

DISCONNECT

32

SS -> MS

RELEASE

33

MS -> SS

RELEASE COMPLETE

34

SS -> MS

CHANNEL RELEASE

The main signalling link is released.

Specific Message Contents:

For 450/900 MS:

PAGING RESPONSE

Information element

Value/remark

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

CLASSMARK CHANGE

Information element

Value/remark

Protocol Discriminator

RR management

Mobile station Classmark

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

Additional MS Classmark information

– Band 1 (P-GSM) supported

According to PICS statement

– Band 2 (E-GSM) supported

According to PICS statement

– GSM 400 Band supported

According to PICS statement

– R-Band (R-GSM) supported

According to PICS statement

– ER-Band (ER-GSM) supported

According to PICS statement

– GSM 400 Associated radio capability

Corresponding to GSM 450 band

– Associated radio capability 1

Corresponding to GSM 900 band

– R-Band Associated radio capability

Corresponding to R-GSM 900 band

HANDOVER COMMAND

Information element

Value/remark

Protocol Discriminator

RR management

Cell Description

– NCC

1

– BCC

5

– BCCH Carrier Number

20

Channel description

– Channel type

TCH/F + ACCH’s

– Timeslot number

Arbitrary value

– Training sequence code

Chosen arbitrarily

– Hopping

Single RF channel

– ARFCN

50

Handover Reference

Chosen arbitrarily from the range (0,1…255)

Power Command & Access type

– Power level

Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.

– Access type control

Sending of HANDOVER ACCESS is mandatory.

Synchronization Indication

pre-synchronized; ROT=0; NCI=0.

Timing Advance

same as in IMMEDIATE ASSIGNMENT

Mode of the first channel

appropriate for the selected bearer service

For 480/900 MS:

PAGING RESPONSE

Information element

Value/remark

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

CLASSMARK CHANGE

Information element

Value/remark

Protocol Discriminator

RR management

Mobile station Classmark

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

Additional MS Classmark information

– Band 1 (P-GSM) supported

According to PICS statement

– Band 2 (E-GSM) supported

According to PICS statement

– GSM 400 Band supported

According to PICS statement

– R-Band (R-GSM) supported

According to PICS statement

– ER-Band (ER-GSM) supported

According to PICS statement

– GSM 400 Associated radio capability

Corresponding to GSM 480 band

– Associated radio capability 1

Corresponding to GSM 900 band

– R-Band Associated radio capability

Corresponding to R-GSM 900 band

HANDOVER COMMAND

Information element

Value/remark

Protocol Discriminator

RR management

Cell Description

– NCC

1

– BCC

5

– BCCH Carrier Number

20

Channel description

– Channel type

TCH/F + ACCH’s

– Timeslot number

Arbitrary value

– Training sequence code

Chosen arbitrarily

– Hopping

Single RF channel

– ARFCN

50

Handover Reference

Chosen arbitrarily from the range (0,1…255)

Power Command & Access type

– Power level

Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.

– Access type control

Sending of HANDOVER ACCESS is mandatory.

Synchronization Indication

pre-synchronized; ROT=0; NCI=0.

Timing Advance

same as in IMMEDIATE ASSIGNMENT

Mode of the first channel

appropriate for the selected bearer service

For 450/1 800 MS:

PAGING RESPONSE

Information element

Value/remark

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

CLASSMARK CHANGE

Information element

Value/remark

Protocol Discriminator

RR management

Mobile station Classmark

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

Additional MS Classmark information

– Band 3 (DCS 1 800) supported

According to PICS statement

– GSM 400 Band supported

According to PICS statement

– GSM 400 Associated radio capability

Corresponding to GSM 450 band

– Associated radio capability 2

Corresponding to DCS 1 800 band

HANDOVER COMMAND

Information element

Value/remark

Protocol Discriminator

RR management

Cell Description

– NCC

1

– BCC

5

– BCCH Carrier Number

590

Channel description

– Channel type

TCH/F + ACCH’s

– Timeslot number

Arbitrary value

– Training sequence code

Chosen arbitrarily

– Hopping

Single RF channel

– ARFCN

650

Handover Reference

Chosen arbitrarily from the range (0,1…255)

Power Command & Access type

– Power level

Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.

– Access type control

Sending of HANDOVER ACCESS is mandatory.

Synchronization Indication

pre-synchronized; ROT=0; NCI=0.

Timing Advance

same as in IMMEDIATE ASSIGNMENT

Mode of the first channel

appropriate for the selected bearer service

For 480/1 800 MS:

PAGING RESPONSE

Information element

Value/remark

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

CLASSMARK CHANGE

Information element

Value/remark

Protocol Discriminator

RR management

Mobile station Classmark

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

Additional MS Classmark information

– Band 3 (DCS 1 800) supported

According to PICS statement

– GSM 400 Band supported

According to PICS statement

– GSM 400 Associated radio capability

Corresponding to GSM 480 band

– Associated radio capability 2

Corresponding to DCS 1 800 band

HANDOVER COMMAND

Information element

Value/remark

Protocol Discriminator

RR management

Cell Description

– NCC

1

– BCC

5

– BCCH Carrier Number

590

Channel description

– Channel type

TCH/F + ACCH’s

– Timeslot number

Arbitrary value

– Training sequence code

Chosen arbitrarily

– Hopping

Single RF channel

– ARFCN

650

Handover Reference

Chosen arbitrarily from the range (0,1…255)

Power Command & Access type

– Power level

Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.

– Access type control

Sending of HANDOVER ACCESS is mandatory.

Synchronization Indication

pre-synchronized; ROT=0; NCI=0.

Timing Advance

same as in IMMEDIATE ASSIGNMENT

Mode of the first channel

appropriate for the selected bearer service

For 900/1 800 MS:

PAGING RESPONSE

Information element

Value/remark

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

CLASSMARK CHANGE

Information element

Value/remark

Protocol Discriminator

RR management

Mobile station Classmark

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

Additional MS Classmark information

– Band 1 (P-GSM) supported

According to PICS statement

– Band 2 (E-GSM) supported

According to PICS statement

– Band 3 (DCS 1 800) supported

According to PICS statement

– R-Band (R-GSM) supported

According to PICS statement

– ER-Band (ER-GSM) supported

According to PICS statement

– Associated radio capability 1

Corresponding to GSM 900 band

– Associated radio capability 2

Corresponding to DCS 1 800 band

– R-Band Associated radio capability

Corresponding to R-GSM 900 band

HANDOVER COMMAND

Information element

Value/remark

Protocol Discriminator

RR management

Cell Description

– NCC

1

– BCC

5

– BCCH Carrier Number

590

Channel description

– Channel type

TCH/F + ACCH’s

– Timeslot number

Arbitrary value

– Training sequence code

Chosen arbitrarily

– Hopping

Single RF channel

– ARFCN

650

Handover Reference

Chosen arbitrarily from the range (0,1…255)

Power Command & Access type

– Power level

Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.

– Access type control

Sending of HANDOVER ACCESS is mandatory.

Synchronization Indication

pre-synchronized; ROT=0; NCI=0.

Timing Advance

same as in IMMEDIATE ASSIGNMENT

Mode of the first channel

appropriate for the selected bearer service

For 710/1 900 MS, 750/1 900 MS:

PAGING RESPONSE

Information element

Value/remark

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

CLASSMARK CHANGE

Information element

Value/remark

Protocol Discriminator

RR management

Mobile station Classmark

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

Additional MS Classmark information

– GSM 710 Associated radio capability

Corresponding to GSM 710 band

– GSM 750 Associated radio capability

Corresponding to GSM 750 band

– PCS 1 900 Associated radio capability

Corresponding to PCS 1 900 band

HANDOVER COMMAND

Information element

Value/remark

Protocol Discriminator

RR management

Cell Description

– NCC

1

– BCC

5

– BCCH Carrier Number

590

Channel description

– Channel type

TCH/F + ACCH’s

– Timeslot number

Arbitrary value

– Training sequence code

Chosen arbitrarily

– Hopping

Single RF channel

– ARFCN

650

Handover Reference

Chosen arbitrarily from the range (0,1…255)

Power Command & Access type

– Power level

Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.

– Access type control

Sending of HANDOVER ACCESS is mandatory.

Synchronization Indication

pre-synchronized; ROT=0; NCI=0.

Timing Advance

same as in IMMEDIATE ASSIGNMENT

Mode of the first channel

appropriate for the selected bearer service

For 850/1 900 MS:

PAGING RESPONSE

Information element

Value/remark

Mobile station Classmark 2

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

CLASSMARK CHANGE

Information element

Value/remark

Protocol Discriminator

RR management

Mobile station Classmark

– ES IND

Shall indicate early autonomous sending of CLASSMARK CHANGE

– RF power capability

corresponding to the frequency band in use

Additional MS Classmark information

– GSM 850 Associated radio capability

Corresponding to GSM 850 band

– PCS 1 900 Associated radio capability

Corresponding to PCS 1 900 band

HANDOVER COMMAND

Information element

Value/remark

Protocol Discriminator

RR management

Cell Description

– NCC

1

– BCC

5

– BCCH Carrier Number

590

Channel description

– Channel type

TCH/F + ACCH’s

– Timeslot number

Arbitrary value

– Training sequence code

Chosen arbitrarily

– Hopping

Single RF channel

– ARFCN

650

Handover Reference

Chosen arbitrarily from the range (0,1…255)

Power Command & Access type

– Power level

Arbitrarily chosen, but different to the one already in use and within the range supported by the MS.

– Access type control

Sending of HANDOVER ACCESS is mandatory.

Synchronization Indication

pre-synchronized; ROT=0; NCI=0.

Timing Advance

same as in IMMEDIATE ASSIGNMENT

Mode of the first channel

appropriate for the selected bearer service