11.8.2 MS to SS direction
3GPP51.010-1Mobile Station (MS) conformance specificationPart 1: Conformance specificationTS
In the whole subclause 11.8.2, "1)" and "2)" stand for:
1) Not applicable in a CALL CONFIRMED message.
2) Not applicable in a CALL CONFIRMED message responding to a SETUP message with no BC-IE (PSTN-originated call with single numbering scheme).
If the MS supports only Full Rate:
Radio Channel Requirement in Octet 3: |
– |
0 |
1 |
– |
– |
– |
– |
– |
Full rate support only mobile station |
Else
Radio Channel Requirement in Octet 3: |
– |
1 |
x |
– |
– |
– |
– |
– |
Dual rate mobile station |
11.8.2.1 BS 21 to 26 – Asynchronous Service
If the MS supports only SAP I.440/I.450:
SAP in Octet 5: |
– |
– |
– |
– |
– |
0 |
0 |
1 |
I.440/I.450 |
If the MS supports only SAP X.28 non dedicated PAD:
SAP in Octet 5: |
– |
– |
– |
– |
– |
1 |
0 |
1 |
X.28 nond |
Else:
SAP in Octet 5: |
– |
– |
– |
– |
– |
x |
0 |
1 |
I.440/I.450 or X.28 nond |
The use of the alternative configuration "Autobauding modem type 1" in BS 22 to BS 26 is the same as indicated for BS 21 in subclauses 11.8.2.1.1.1 and 11.8.2.1.1.2.
11.8.2.1.1 BS 21
11.8.2.1.1.1 3,1 kHz Audio, Transparent
BC GSM = 04 0X X2 X8 8X 21 X1 XX X1 (CX)
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
x |
x |
x |
x |
Length (7 or 8) depending on the presence of octet 7. |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
1 |
0 |
Info. Transfer Cap.: 3,1 kHz Audio |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
x |
x |
Structure |
|||||||
1 |
Duplex Mode |
||||||||
0 |
Configuration: Point to Point |
||||||||
0 |
Negotiation of Intermediate Rate Requested: No meaning |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
0 |
Rate Adaptation: No |
|||||||
x |
0 |
1 |
Signalling Access Protocol |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
1 |
Synchronous / Asynchronous: Asynchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
x |
Number of Stop Bits, Depending of the TE Configuration |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
x |
Number of Data Bits, Depending of the TE Configuration |
||||||||
0 |
0 |
0 |
1 |
User Rate: 0,3 kbit/s |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
x |
Intermediate Rate: 8kbit/s |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
x |
x |
x |
Parity, Depending of the TE Configuration |
||||||
Octet 6c |
1 |
Extension |
|||||||
x |
x |
Connection Element |
|||||||
0 |
0 |
0 |
0 |
1 |
Modem Type: V.21 |
If the mobile station supports only Transparent mode or responds with a CALL CONFIRMED message:
Structure in Octet 4: |
– |
1 |
1 |
– |
– |
– |
– |
– |
Unstructured |
Intermediate rate in Octet 6b: |
– |
1 |
0 |
– |
– |
– |
– |
– |
8 kbit/s |
Connection element in Octet 6c: |
– |
0 |
0 |
– |
– |
– |
– |
– |
Transparent |
1) If the mobile station supports both Transparent and Non Transparent modes:
Structure in Octet 4: |
– |
0 |
0 |
– |
– |
– |
– |
– |
SDU Integrity |
Intermediate rate in Octet 6b: |
– |
1 |
1 |
– |
– |
– |
– |
– |
16 kbit/s |
Connection element in Octet 6c: |
– |
1 |
x |
– |
– |
– |
– |
– |
Both T or NT preferred |
User Information L2 protocol in Octet 7 (see Non Transparent service)
2) The following configuration is also authorised in the SETUP message:
Connection element in Octet 6c: |
– |
1 |
x |
– |
– |
– |
– |
– |
Both T or NT preferred |
Modem type in Octet 6c (if CE = "both": |
– |
– |
– |
0 |
1 |
0 |
0 |
0 |
Autobauding Type 1 |
11.8.2.1.1.2 3,1 kHz Audio, Non Transparent
BC GSM = 04 0X X2 XX 8X 21 X1 6X X1 (CX)
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
x |
x |
x |
x |
Length (7 or 8) depending on presence of octet 7. |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
1 |
0 |
Info. Transfer Cap.: 3,1 kHz Audio |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
0 |
0 |
Structure: SDU Integrity |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
x |
Negotiation of Intermediate Rate Requested |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
0 |
Rate Adaptation: No |
|||||||
x |
0 |
1 |
Signalling Access Protocol |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
1 |
Synchronous / Asynchronous: Asynchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
x |
Number of Stop Bits, Depending of the TE Configuration |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
x |
Number of Data Bits, Depending of the TE Configuration |
||||||||
0 |
0 |
0 |
1 |
User Rate: 0,3 kbit/s |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
1 |
Intermediate Rate: 16kbit/s |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
x |
x |
x |
Parity, Depending of the TE Configuration |
||||||
Octet 6c |
1 |
Extension |
|||||||
x |
x |
Connection Element: NT, (Both T or Both NT)1) |
|||||||
0 |
0 |
0 |
0 |
1 |
Modem Type: V.21 |
||||
Octet 7 (need not be present) |
1 |
Extension |
|||||||
1 |
0 |
Layer 2 Id. |
|||||||
0 |
1 |
x |
0 |
0 |
User Inform. layer 2 protocol, Depending on the TE Configuration |
The following configuration is also authorised:
Modem type in Octet 6c: |
– |
– |
– |
0 |
1 |
0 |
0 |
0 |
Autobauding Type 1 |
Depending of the type of flow control supported by the TE, the coding of octet 7 is different. The value ISO 6429 (0 1000) means "Inband flow control" and the value COPnoFLCT (0 1100) means "No flow control".
11.8.2.1.1.3 2) UDI, Transparent
BC GSM = 04 0X X1 X8 8X 21 X1 XX X0
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
x |
x |
x |
x |
Length (7 or 8) depending on the presence of octet 7 |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
0 |
1 |
Info. Transfer Cap.: UDI |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
x |
x |
Structure |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
0 |
Negotiation of Intermediate Rate Requested: No meaning |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
1 |
Rate Adaptation: V.110 |
|||||||
x |
0 |
1 |
Signalling Access Protocol |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
1 |
Synchronous / Asynchronous: Asynchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
x |
Number of Stop Bits, Depending of the TE Configuration |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
x |
Number of Data Bits, Depending of the TE Configuration |
||||||||
0 |
0 |
0 |
1 |
User Rate: 0,3 kbit/s |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
x |
Intermediate Rate |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
x |
x |
x |
Parity, Depending of the TE Configuration |
||||||
Octet 6c |
1 |
Extension |
|||||||
x |
x |
Connection Element |
|||||||
0 |
0 |
0 |
0 |
0 |
Modem Type: None |
If the mobile station supports only Transparent mode or responds with a CALL CONFIRMED message:
Structure in Octet 4: |
– |
1 |
1 |
– |
– |
– |
– |
– |
Unstructured |
Intermediate rate in Octet 6b: |
– |
1 |
0 |
– |
– |
– |
– |
– |
8 kbit/s |
Connection element in Octet 6c: |
– |
0 |
0 |
– |
– |
– |
– |
– |
Transparent |
1) If the mobile station supports both Transparent and Non Transparent modes:
Structure in Octet 4: |
– |
0 |
0 |
– |
– |
– |
– |
– |
SDU Integrity |
Intermediate rate in Octet 6b: |
– |
1 |
1 |
– |
– |
– |
– |
– |
16 kbit/s |
Connection element in Octet 6c: |
– |
1 |
x |
– |
– |
– |
– |
– |
Both T or NT preferred |
User Information L2 protocol in Octet 7 (see Non Transparent service).
11.8.2.1.1.4 2) UDI, Non Transparent
BC GSM = 04 0X X1 XX 8X 21 X1 6X X0 (CX)
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
x |
x |
x |
x |
Length (7 or 8) depending on presence of octet 7. |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
0 |
1 |
Info. Transfer Cap.: UDI |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
0 |
0 |
Structure: SDU Integrity |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
x |
Negotiation of Intermediate Rate Requested |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
1 |
Rate Adaptation: V.110 |
|||||||
x |
0 |
1 |
Signalling Access Protocol |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
1 |
Synchronous / Asynchronous: Asynchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
x |
Number of Stop Bits, Depending of the TE Configuration |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
x |
Number of Data Bits, Depending of the TE Configuration |
||||||||
0 |
0 |
0 |
1 |
User Rate: 0,3 kbit/s |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
1 |
Intermediate Rate: 16kbit/s |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
x |
x |
x |
Parity, Depending of the TE Configuration |
||||||
Octet 6c |
1 |
Extension |
|||||||
x |
x |
Connection Element: NT, (Both T or Both NT) 1) |
|||||||
0 |
0 |
0 |
0 |
0 |
Modem Type: None |
||||
Octet 7 (need not be present) |
1 |
Extension |
|||||||
1 |
0 |
Layer 2 Id. |
|||||||
0 |
1 |
x |
0 |
0 |
User Inform. layer 2 protocol, Depending of the TE Configuration |
Depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control". If octet 7 is present, the value ISO 6429 (0 1000) means "Inband flow control" and the value COPnoFLCT (0 1100) means "No flow control".
11.8.2.1.2 BS 22
Same as BS 21 except:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
1 |
0 |
1,2 kbit/s |
|
If different from "none", |
Modem Type Octet 6c: |
– |
– |
– |
0 |
0 |
0 |
1 |
0 |
Modem V.22 |
In case of 3,1 kHz Audio non transparent service, depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control".
11.8.2.1.3 BS 24
Same as BS 21 except:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
1 |
1 |
2,4 kbit/s |
|
If different from "none", |
Modem Type Octet 6c: |
– |
– |
– |
0 |
0 |
0 |
1 |
1 |
Modem V.22bis |
1 |
0 |
1 |
Modem V.26ter |
In case of 3,1kHz Audio non transparent service, depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control".
11.8.2.1.4 BS 25
Same as BS 21 except:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
0 |
4,8 kbit/s |
|
If different from "none", |
Modem Type Octet 6c: |
– |
– |
– |
0 |
0 |
1 |
1 |
0 |
Modem V.32 |
In case of 3,1 kHz Audio non transparent service, depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control".
11.8.2.1.5 BS 26
Same as BS 21 except:
NIRR in Octet 4: |
– |
– |
– |
– |
– |
– |
0 |
– |
no meaning |
|
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
1 |
9,6 kbit/s |
|
Interm. Rate in Octet 6b: |
– |
1 |
1 |
– |
– |
– |
– |
– |
16 kbit/s |
|
If different from "none", |
Modem Type Octet 6c: |
– |
– |
– |
0 |
0 |
1 |
1 |
0 |
Modem V.32 |
In case of 3,1kHz Audio non transparent service, depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control".
11.8.2.1.6 BS 23
Same as BS 21 except:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
1 |
1 |
1,2 kbit/s/75 bit/s |
|
If different from "none", |
Modem Type Octet 6c: |
– |
– |
– |
0 |
0 |
1 |
0 |
0 |
Modem V.23 |
In case of 3,1kHz Audio non transparent service, depending of the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control".
11.8.2.2 BS 31 to 34 – Synchronous Service
11.8.2.2.1 BS 32
11.8.2.2.1.1 3,1 kHz Audio, Transparent, non-X.32 case
BC GSM = 04 07 X2 X8 81 20 13 43 83
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
1 |
Length |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement : Spare |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
1 |
0 |
Info. Transfer Cap.: 3,1 kHz Audio |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
1 |
1 |
Structure: Unstructured |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
0 |
Negotiation of Intermediate Rate Requested: No meaning |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
0 |
Rate Adaptation: No |
|||||||
0 |
0 |
1 |
Signalling Access Protocol: I.440 / I.450 |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
0 |
Synchronous / Asynchronous: Synchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
0 |
Number of Stop Bits: NA |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
1 |
Number of Data Bits: NA |
||||||||
0 |
0 |
1 |
1 |
User Rate: 2,4 kbit/s |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
0 |
Intermediate Rate: 8kbit/s |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
0 |
1 |
1 |
Parity: NA |
||||||
Octet 6c |
1 |
Extension |
|||||||
0 |
0 |
Connection Element: Transparent |
|||||||
0 |
0 |
x |
x |
1 |
Modem Type: V.22 bis or V.26 ter |
11.8.2.2.1.2 2) UDI, Transparent mode, non-X.32 case
BC GSM = 04 07 X1 X8 8X 20 13 43 80
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
1 |
Length |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
0 |
1 |
Info. Transfer Cap.: UDI |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
1 |
1 |
Structure: Unstructured |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
0 |
Negotiation of Intermediate Rate Requested: No meaning |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
1 |
Rate Adaptation: V.110 |
|||||||
0 |
x |
x |
Signalling Access Protocol |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
0 |
Synchronous / Asynchronous: Synchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
0 |
Number of Stop Bits: NA |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
1 |
Number of Data Bits: NA |
||||||||
0 |
0 |
1 |
1 |
User Rate: 2,4 kbit/s |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
0 |
Intermediate Rate: 8kbit/s |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
0 |
1 |
1 |
Parity: NA |
||||||
Octet 6c |
1 |
Extension |
|||||||
0 |
0 |
Connection Element: Transparent |
|||||||
0 |
0 |
0 |
0 |
0 |
Modem Type: none |
If the mobile station supports only SAP I.440/450
SAP in Octet 5: |
– |
– |
– |
– |
– |
0 |
0 |
1 |
I.440/I.450 |
If the MS supports only SAP X.21
SAP in Octet 5: |
– |
– |
– |
– |
– |
0 |
1 |
0 |
X.21 |
Else
SAP in Octet 5: |
– |
– |
– |
– |
– |
0 |
x |
x |
I.440/I.450 or X.21 |
11.8.2.2.1.3 3,1 kHz Audio, Transparent mode, X.32 case (Packet Service)
BC GSM = 04 0X X2 X8 86 20 13 X3 X3 (C6)
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
1 |
Length |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
1 |
0 |
Info. Transfer Cap.: 3,1 kHz Audio |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
x |
x |
Structure |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
0 |
Negotiation of Intermediate Rate Requested: No meaning |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
0 |
Rate Adaptation: No |
|||||||
1 |
1 |
0 |
Signalling Access Protocol: X.32 |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
0 |
Synchronous / Asynchronous: Synchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
0 |
Number of Stop Bits: NA |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
1 |
Number of Data Bits: NA |
||||||||
0 |
0 |
1 |
1 |
User Rate: 2,4 kbit/s |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
x |
Intermediate Rate |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
0 |
1 |
1 |
Parity: NA |
||||||
Octet 6c |
1 |
Extension |
|||||||
x |
x |
Connection Element: Transparent |
|||||||
0 |
0 |
x |
x |
1 |
Modem Type: V.22 bis or V.26 ter |
||||
If the mobile station supports only Transparent mode or responds with a CALL CONFIRMED message:
Structure in Octet 4: |
– |
1 |
1 |
– |
– |
– |
– |
– |
Unstructured |
Intermediate rate in Octet 6b: |
– |
1 |
0 |
– |
– |
– |
– |
– |
8 kbit/s |
Connection element in Octet 6c: |
– |
0 |
0 |
– |
– |
– |
– |
– |
Transparent |
1) If the mobile station supports both Transparent and Non Transparent modes:
Structure in Octet 4: |
– |
0 |
0 |
– |
– |
– |
– |
– |
SDU Integrity |
Intermediate rate in Octet 6b: |
– |
1 |
1 |
– |
– |
– |
– |
– |
16 kbit/s |
Connection element in Octet 6c: |
– |
1 |
x |
– |
– |
– |
– |
– |
Both T or NT preferred |
UIL2P in Octet 7 |
– |
– |
– |
0 |
0 |
1 |
1 |
0 |
X.25 |
11.8.2.2.1.4 3,1 kHz Audio, Non Transparent mode, X.32 case (Packet Service)
BC GSM = 04 08 A2 XX 86 20 13 63 X3 C6
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
0 |
Length |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
1 |
0 |
Info. Transfer Cap.: 3,1 kHz Audio |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
0 |
0 |
Structure: SDU integrity |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
x |
Negotiation of Intermediate Rate Requested |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
0 |
Rate Adaptation: No |
|||||||
1 |
1 |
0 |
Signalling Access Protocol: X.32 |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
0 |
Synchronous / Asynchronous: Synchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
0 |
Number of Stop Bits: NA |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
1 |
Number of Data Bits: NA |
||||||||
0 |
0 |
1 |
1 |
User Rate: 2,4 kbit/s |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
1 |
Intermediate Rate: 16kbit/s |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
0 |
1 |
1 |
Parity: NA |
||||||
Octet 6c |
1 |
Extension |
|||||||
x |
x |
Connection Element: NT, (Both T or Both NT)1) |
|||||||
0 |
0 |
x |
x |
1 |
Modem Type: V.22 bis or V.26 ter |
||||
Octet 7 |
1 |
Extension |
|||||||
1 |
0 |
Layer 2 Id. |
|||||||
0 |
0 |
1 |
1 |
0 |
X.25 |
11.8.2.2.1.5 2) UDI, Non Transparent mode, X.32 case (Packet Service)
BC GSM = 04 08 X1 XX 96 20 13 63 A0 C6
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
0 |
Length |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
0 |
1 |
Info. Transfer Cap.: UDI |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
0 |
0 |
Structure: SDU integrity |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
x |
Negotiation of Intermediate Rate Requested |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
1 |
0 |
Rate Adaptation: X.31 flagstuffing |
|||||||
1 |
1 |
0 |
Signalling Access Protocol: X.32 |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
0 |
Synchronous / Asynchronous: Synchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
0 |
Number of Stop Bits: NA |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
1 |
Number of Data Bits: NA |
||||||||
0 |
0 |
1 |
1 |
User Rate: 2,4 kbit/s |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
1 |
Intermediate Rate: 16kbit/s |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
0 |
1 |
1 |
Parity: NA |
||||||
Octet 6c |
1 |
Extension |
|||||||
0 |
1 |
Connection Element: Non Transparent |
|||||||
0 |
0 |
0 |
0 |
0 |
Modem Type: None |
||||
Octet 7 |
1 |
Extension |
|||||||
1 |
0 |
Layer 2 Id. |
|||||||
0 |
0 |
1 |
1 |
0 |
X.25 |
11.8.2.2.2 BS 31
For non X.32 case only, same as BS 32 except:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
1 |
0 |
1,2 kbit/s |
|
If different from "none", |
Modem Type Octet 6c: |
– |
– |
– |
0 |
0 |
0 |
1 |
0 |
Modem V.22 |
BS31 for Packet Service does not exist.
11.8.2.2.3 BS 33
Same as BS 32 except:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
0 |
4,8 kbit/s |
|
If different from "none", |
Modem Type Octet 6c: |
– |
– |
– |
0 |
0 |
1 |
1 |
0 |
Modem V.32 |
11.8.2.2.4 BS 34
Same as BS 32 except:
NIRR in Octet 4: |
– |
– |
– |
– |
– |
– |
0 |
– |
no meaning |
|
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
1 |
9,6 kbit/s |
|
Interm. Rate in Octet 6b: |
– |
1 |
1 |
– |
– |
– |
– |
– |
16 kbit/s |
|
If different from "none", |
Modem Type Octet 6c: |
– |
– |
– |
0 |
0 |
1 |
1 |
0 |
Modem V.32 |
11.8.2.3 BS 41 to 46 – PAD Access Asynchronous
11.8.2.3.1 2) BS 41
11.8.2.3.1.1 2) UDI, Transparent
BC GSM = 04 0X X1 X8 8C 21 X1 XX X0 (CX)
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
1 |
Length |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
0 |
1 |
Info. Transfer Cap.: UDI |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
x |
x |
Structure |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
0 |
Negotiation of Intermediate Rate Requested: No meaning |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
1 |
Rate Adaptation: V.110 |
|||||||
1 |
0 |
0 |
Signalling Access Protocol: X.28 dedicated universal NUI |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
1 |
Synchronous / Asynchronous: Asynchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
x |
Number of Stop Bits, Depending of the TE Configuration |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
x |
Number of Data Bits, Depending of the TE Configuration |
||||||||
0 |
0 |
0 |
1 |
User Rate: 0,3 kbit/s |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
x |
Intermediate Rate |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
x |
x |
x |
Parity, Depending of the TE Configuration |
||||||
Octet 6c |
1 |
Extension |
|||||||
x |
x |
Connection Element |
|||||||
0 |
0 |
0 |
0 |
0 |
Modem Type: None |
If the mobile station supports only Transparent mode or responds with a CALL CONFIRMED message:
Structure in Octet 4: |
– |
1 |
1 |
– |
– |
– |
– |
– |
Unstructured |
Intermediate rate in Octet 6b: |
– |
1 |
0 |
– |
– |
– |
– |
– |
8 kbit/s |
Connection element in Octet 6c: |
– |
0 |
0 |
– |
– |
– |
– |
– |
Transparent |
1) If the mobile station supports both Transparent and Non Transparent modes:
Structure in Octet 4: |
– |
0 |
0 |
– |
– |
– |
– |
– |
SDU Integrity |
Intermediate rate in Octet 6b: |
– |
1 |
1 |
– |
– |
– |
– |
– |
16 kbit/s |
Connection element in Octet 6c: |
– |
1 |
x |
– |
– |
– |
– |
– |
Both T or NT preferred |
User Information L2 Protocol (see Non Transparent service).
11.8.2.3.1.2 2) UDI, Non transparent
BC GSM = 04 08 X1 XX 8C 21 X1 6X X0 CX
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
0 |
Length. |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
0 |
1 |
Info. Transfer Cap.: UDI |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
0 |
0 |
Structure: SDU Integrity |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
x |
Negotiation of Intermediate Rate Requested |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
1 |
Rate Adaptation: V.110 |
|||||||
1 |
0 |
0 |
Signalling Access Protocol: X.28 dedicated PAD, universal NUI |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
1 |
Synchronous / Asynchronous: Asynchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
x |
Number of Stop Bits, Depending of the TE Configuration |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
x |
Number of Data Bits, Depending of the TE Configuration |
||||||||
0 |
0 |
0 |
1 |
User Rate: 0,3 kbit/s |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
1 |
Intermediate Rate: 16kbit/s |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
x |
x |
x |
Parity, Depending of the TE Configuration |
||||||
Octet 6c |
1 |
Extension |
|||||||
x |
x |
Connection Element: NT, (Both T or Both NT)1) |
|||||||
0 |
0 |
0 |
0 |
0 |
Modem Type: None |
||||
Octet 7 |
1 |
Extension |
|||||||
1 |
0 |
Layer 2 Id. |
|||||||
0 |
1 |
x |
0 |
0 |
User Inform. layer 2 protocol: Depending on the TE Configuration |
Depending on the type of flow control supported by the TE, octet 7 is present or not. If not present, it means "outband flow control". If octet 7 is present, the value COPnoFLCT (01100) means "No flow control".
11.8.2.3.2 BS 42
Same as BS 41 except:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
1 |
0 |
1,2 kbit/s |
11.8.2.3.3 BS 44
Same as BS 41 except:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
1 |
1 |
2,4 kbit/s |
11.8.2.3.4 BS 45
Same as BS 41 except:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
0 |
4,8 kbit/s |
11.8.2.3.5 BS 46
Same as BS 41 except:
NIRR in Octet 4 |
– |
– |
– |
– |
– |
– |
0 |
– |
no meaning |
|
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
1 |
9,6 kbit/s |
|
Interm. Rate in Octet 6b: |
– |
1 |
1 |
– |
– |
– |
– |
– |
16 kbit/s |
11.8.2.3.6 BS 43
Same as BS 41 except:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
1 |
1 |
1,2 kbit/s 75bit/s |
11.8.2.4 BS 51 to 53 – Packet Service Synchronous
11.8.2.4.1 2) BS 51
BC GSM = 04 08 X1 X8 96 20 13 63 A0 C6
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
0 |
Length |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
0 |
1 |
Info. Transfer Cap.: UDI |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
0 |
0 |
Structure: Unstructured |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
0 |
Negotiation of Intermediate Rate Requested: No meaning |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
1 |
0 |
Rate Adaptation: X.31 flag. |
|||||||
1 |
1 |
0 |
Signalling Access Protocol: X.32 |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
0 |
Synchronous / Asynchronous: Synchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
0 |
Number of Stop Bits: NA |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
1 |
Number of Data Bits: NA |
||||||||
0 |
0 |
1 |
1 |
User Rate: 2,4 kbit/s |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
1 |
Intermediate Rate: 16kbit/s |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
0 |
1 |
1 |
Parity: NA |
||||||
Octet 6c |
1 |
Extension |
|||||||
0 |
1 |
Connection Element: Non Transparent |
|||||||
0 |
0 |
0 |
0 |
0 |
Modem Type: None |
||||
Octet 7 |
1 |
Extension |
|||||||
1 |
0 |
Layer 2 Id. |
|||||||
0 |
0 |
1 |
1 |
0 |
X.25 |
11.8.2.4.2 BS 52
Same as BS 51 except:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
0 |
4,8 kbit/s |
11.8.2.4.3 BS 53
Same as BS 51 except:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
1 |
9,6 kbit/s |
11.8.2.5 BS 61 – Alternate Speech / Data
The first BC is coded as follows:
IF: speech full rate version 2 is supported by the mobile, see subclause 11.8.2.9.2;
ELSE: see subclause 11.8.2.9.1.
The repeat Indicator in the Setup message is coded "Circular for successive selection (alternate)": D1.
The second BC in the Setup message is coded as described below.
11.8.2.5.1 Speech/Asynchronous Data, Transparent
BC GSM = 04 0X X2 X8 81 21 XX XX XX (CX)
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
1 |
Length |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
1 |
0 |
Info. Transfer Cap.: 3,1 kHz Audio |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
x |
x |
Structure |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
0 |
Negotiation of Intermediate Rate Requested: No meaning |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
0 |
Rate Adaptation: No |
|||||||
0 |
0 |
1 |
Signalling Access Protocol: I.440 / I.450 |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
1 |
Synchronous / Asynchronous: Asynchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
x |
Number of Stop Bits, Depending of the TE Configuration |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
x |
Number of Data Bits, Depending of the TE Configuration |
||||||||
x |
x |
x |
x |
User Rate |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
x |
Intermediate Rate |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
x |
x |
x |
Parity, Depending of the TE Configuration |
||||||
Octet 6c |
1 |
Extension |
|||||||
x |
x |
Connection Element |
|||||||
0 |
x |
x |
x |
x |
Modem Type |
If the mobile station supports only Transparent mode or responds with a CALL CONFIRMED message:
Structure in Octet 4: |
– |
1 |
1 |
– |
– |
– |
– |
– |
Unstructured |
Intermediate rate in Octet 6b: |
– |
1 |
x |
– |
– |
– |
– |
– |
Depending on the user rate |
Connection element in Octet 6c: |
– |
0 |
0 |
– |
– |
– |
– |
– |
Transparent |
1) If the mobile station supports both Transparent and Non Transparent modes
Structure in Octet 4: |
– |
0 |
0 |
– |
– |
– |
– |
– |
SDU Integrity |
Intermediate rate in Octet 6b: |
– |
1 |
1 |
– |
– |
– |
– |
– |
16 kbit/s |
Connection element in Octet 6c: |
– |
1 |
x |
– |
– |
– |
– |
– |
Both T or NT preferred |
User Information L2 protocol in Octet 7 (see Non Transparent service)
Depending of the user rate supported by the MS, the user rate, the modem type and the intermediate rate change:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
0 |
1 |
0,3 kbit/s |
|
Intermediate rate in Octet 6b: |
– |
1 |
0 |
– |
– |
– |
– |
– |
8 kbit/s in Transparent mode |
|
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
0 |
0 |
1 |
Modem V.21 |
1) The following configuration is also authorised if CE = Both:
Modem type in Octet 6c: |
– |
– |
– |
0 |
1 |
0 |
0 |
0 |
Autobauding Type 1 |
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
1 |
0 |
1,2 kbit/s |
|
Intermediate rate in Octet 6b: |
– |
1 |
0 |
– |
– |
– |
– |
– |
8 kbit/s in Transparent mode |
|
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
0 |
1 |
0 |
Modem V.22 |
1) The following configuration is also authorised if CE = Both:
Modem type in Octet 6c: |
– |
– |
– |
0 |
1 |
0 |
0 |
0 |
Autobauding Type 1 |
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
1 |
1 |
2,4 kbit/s |
|
Intermediate rate in Octet 6b: |
– |
1 |
0 |
– |
– |
– |
– |
– |
8 kbit/s in Transparent mode |
|
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
0 |
1 |
1 |
Modem V.22bis |
|
1 |
0 |
1 |
Modem V.26ter |
1) The following configuration is also authorised if CE = Both:
Modem type in Octet 6c: |
– |
– |
– |
0 |
1 |
0 |
0 |
0 |
Autobauding Type 1 |
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
0 |
4,8 kbit/s |
|
Intermediate rate in Octet 6b: |
– |
1 |
0 |
– |
– |
– |
– |
– |
8 kbit/s in Transparent mode |
|
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
1 |
1 |
0 |
Modem V.32 |
1) The following configuration is also authorised if CE = Both:
Modem type in Octet 6c: |
– |
– |
– |
0 |
1 |
0 |
0 |
0 |
Autobauding Type 1 |
NIRR in Octet 4: |
– |
– |
– |
– |
– |
– |
0 |
– |
no meaning |
|
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
1 |
9,6 kbit/s |
|
Intermediate rate in Octet 6b: |
– |
1 |
1 |
– |
– |
– |
– |
– |
16 kbit/s in Transparent mode |
|
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
1 |
1 |
0 |
Modem V.32 |
1) The following configuration is also authorised if CE = Both:
Modem type in Octet 6c: |
– |
– |
– |
0 |
1 |
0 |
0 |
0 |
Autobauding Type 1 |
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
1 |
1 |
1,2 kbits/s 75bit/2 |
|
Intermediate rate in Octet 6b: |
– |
1 |
0 |
– |
– |
– |
– |
– |
8 kbit/s in Transparent mode |
|
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
1 |
0 |
0 |
Modem V.23 |
1) The following configuration is also authorised if CE = Both:
Modem type in Octet 6c: |
– |
– |
– |
0 |
1 |
0 |
0 |
0 |
Autobauding Type 1 |
11.8.2.5.2 Speech/Asynchronous Data, Non Transparent
BC GSM = 04 0X X2 XX 81 21 XX 6X XX (CX)
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
x |
x |
x |
x |
Length (7 or 8) depending on presence of octet 7. |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
1 |
0 |
Info. Transfer Cap.: 3,1 kHz Audio |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
0 |
0 |
Structure: SDU Integrity |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
x |
Negotiation of Intermediate Rate Requested |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
0 |
Rate Adaptation: No |
|||||||
0 |
0 |
1 |
Signalling Access Protocol: I.440 / I.450 |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
1 |
Synchronous / Asynchronous: Asynchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
x |
Number of Stop Bits, Depending of the TE Configuration |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
x |
Number of Data Bits, Depending of the TE Configuration |
||||||||
x |
x |
x |
x |
User Rate |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
1 |
Intermediate Rate: 16kbit/s |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
x |
x |
x |
Parity, Depending of the TE Configuration |
||||||
Octet 6c |
1 |
Extension |
|||||||
x |
x |
Connection Element: NT, (Both T or Both NT)1) |
|||||||
0 |
x |
x |
x |
x |
Modem Type |
||||
Octet 7 (may not be present) |
1 |
Extension |
|||||||
1 |
0 |
Layer 2 Id. |
|||||||
0 |
1 |
x |
0 |
0 |
User Inform. layer 2 protocol, Depending of the TE Configuration |
Depending of the type of flow control supported by the TE, the coding of octet 7 is different. The value ISO 6429 (0 1000) means "Inband flow control" and the value COPnoFLCT (0 1100) means "No flow control". The "Outband Flow control is not allowed with V.21 modem).
Depending of the user rate supported by the MS, the user rate and the modem type change:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
0 |
1 |
0,3 kbit/s |
||
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
0 |
0 |
1 |
Modem V.21 |
||
– |
– |
– |
0 |
1 |
0 |
0 |
0 |
Autobauding Type 1 |
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
1 |
0 |
1,2 kbit/s |
||
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
0 |
1 |
0 |
Modem V.22 |
||
– |
– |
– |
0 |
1 |
0 |
0 |
0 |
Autobauding Type 1 |
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
1 |
1 |
2,4 kbit/s |
||
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
0 |
1 |
1 |
Modem V.22bis |
||
1 |
0 |
1 |
Modem V.26ter |
||||||||
– |
– |
– |
0 |
1 |
0 |
0 |
0 |
Autobauding Type 1 |
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
0 |
4,8 kbit/s |
||
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
1 |
1 |
0 |
Modem V.32 |
||
– |
– |
– |
0 |
1 |
0 |
0 |
0 |
Autobauding Type 1 |
NIRR in Octet 4: |
– |
– |
– |
– |
– |
– |
0 |
– |
no meaning |
||
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
1 |
9,6 kbit/s |
||
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
1 |
1 |
0 |
Modem V.32 |
||
– |
– |
– |
0 |
1 |
0 |
0 |
0 |
Autobauding Type 1 |
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
1 |
1 |
1,2 kbit/s 75bit/s |
||
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
1 |
0 |
0 |
Modem V.23 |
||
– |
– |
– |
0 |
1 |
0 |
0 |
0 |
Autobauding Type 1 |
11.8.2.5.3 Speech/Synchronous Data
BC GSM = 04 07 X2 X8 81 20 1X X3 8X
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
1 |
Length |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
1 |
0 |
Info. Transfer Cap.: 3,1 kHz Audio |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
1 |
1 |
Structure: Unstructured |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
0 |
Negotiation of Intermediate Rate Requested: No meaning |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
0 |
Rate Adaptation: No |
|||||||
0 |
0 |
1 |
Signalling Access Protocol: I.440 / I.450 |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
0 |
Synchronous / Asynchronous: Synchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
0 |
Number of Stop Bits: NA |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
1 |
Number of Data Bits: NA |
||||||||
x |
x |
x |
x |
User Rate |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
x |
Intermediate Rate |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
0 |
1 |
1 |
Parity: NA |
||||||
Octet 6c |
1 |
Extension |
|||||||
0 |
0 |
Connection Element: Transparent |
|||||||
0 |
x |
x |
x |
x |
Modem Type |
Depending of the user rate supported by the MS, the user rate, the modem type and the intermediate rate change:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
1 |
0 |
1,2 kbit/s |
|
Intermediate rate in Octet 6b: |
– |
1 |
0 |
– |
– |
– |
– |
– |
8 kbit/s |
|
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
0 |
1 |
0 |
Modem V.22 |
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
1 |
1 |
2,4 kbit/s |
|
Intermediate rate in Octet 6b: |
– |
1 |
0 |
– |
– |
– |
– |
– |
8 kbit/s |
|
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
0 |
1 |
1 |
Modem V.22bis |
|
1 |
0 |
1 |
Modem V.26ter |
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
0 |
4,8 kbit/s |
|
Intermediate rate in Octet 6b: |
– |
1 |
0 |
– |
– |
– |
– |
– |
8 kbit/s |
|
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
1 |
1 |
0 |
Modem V.32 |
NIRR in Octet 4: |
– |
– |
– |
– |
– |
– |
0 |
– |
no meaning |
|
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
1 |
9,6 kbit/s |
|
Intermediate rate in Octet 6b: |
– |
1 |
1 |
– |
– |
– |
– |
– |
16 kbit/s |
|
Modem type in Octet 6c: |
– |
– |
– |
0 |
0 |
1 |
1 |
0 |
Modem V.32 |
11.8.2.6 BS 81 – Speech followed by Data
The first BC is coded as follows:
IF: speech full rate version 2 is supported by the mobile, see subclause 11.8.2.9.2.
ELSE: see subclause 11.8.2.9.1.
The repeat Indicator in the Setup message is coded "Circular for successive selection ‘mode 1 alternate mode 2’ : D1".
The second BC in the Setup message is coded as described below.
11.8.2.6.1 Speech followed by Asynchronous Data
See subclauses 11.8.2.5.1 and 11.8.2.5.2.
11.8.2.6.2 Speech followed by Synchronous Data
See subclause 11.8.2.5.3.
11.8.2.7 TS 61 – Alternate Speech / Facsimile group 3
The first BC is coded as follows:
IF: speech full rate version 2 is supported by the mobile, see subclause 11.8.2.9.2.
ELSE: see subclause 11.8.2.9.1.
The repeat Indicator in the Setup message is coded "Circular for successive selection (alternate)": D1.
The second BC in the Setup message is coded as described below.
11.8.2.7.1 TS 61 – Alternate Speech / Facsimile group 3, Transparent
BC GSM = 04 07 X3 X8 81 20 1X X3 80
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
1 |
Length |
Octet 3 |
1 |
Extension |
|||||||
y |
y |
Radio Channel Requirement: Spare |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
1 |
1 |
Info. Transfer Cap.: FAX3 |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
1 |
1 |
Structure: Unstructured |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
0 |
Negotiation of Intermediate Rate Requested: No meaning |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
0 |
Rate Adaptation: No |
|||||||
0 |
0 |
1 |
Signalling Access Protocol: NA |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
0 |
Synchronous / Asynchronous: synchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
0 |
Number of Stop Bits: NA |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
1 |
Number of Data Bits: NA |
||||||||
x |
x |
x |
x |
User Rate |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
x |
Intermediate Rate |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
0 |
1 |
1 |
Parity: NA |
||||||
Octet 6c |
1 |
Extension |
|||||||
0 |
0 |
Connection Element: Transparent |
|||||||
0 |
0 |
0 |
0 |
0 |
Modem Type: None |
Depending of the user rate supported by the MS, the user rate and the intermediate rate change:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
1 |
1 |
2,4 kbit/s |
|
Interm. Rate in Octet 6b: |
– |
1 |
0 |
– |
– |
– |
– |
– |
8 kbit/s |
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
0 |
4,8 kbit/s |
|
Interm. Rate in Octet 6b: |
– |
1 |
0 |
– |
– |
– |
– |
– |
8 kbit/s |
NIRR in Octet 4: |
– |
– |
– |
– |
– |
– |
0 |
– |
no meaning |
|
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
1 |
9,6 kbit/s |
|
Interm. Rate in Octet 6b: |
– |
1 |
1 |
– |
– |
– |
– |
– |
16 kbit/s |
11.8.2.7.2 TS 61 – Alternate Speech / Facsimile group 3, Non Transparent
BC GSM = 04 07 X3 XX 81 20 1X 63 X0 66
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element: Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
1 |
Length |
Octet 3 |
1 |
Extension |
|||||||
y |
y |
Radio Channel Requirement: Spare |
|||||||
0 |
Coding Standard: GSM |
||||||||
0 |
Transfer Mode: Circuit |
||||||||
0 |
1 |
1 |
Info. Transfer Cap.: FAX3 |
||||||
Octet 4 |
1 |
Extension |
|||||||
y |
Spare |
||||||||
0 |
0 |
Structure: SDU Integrity |
|||||||
1 |
Duplex Mode: Full duplex |
||||||||
0 |
Configuration: Point to Point |
||||||||
x |
Negotiation of Intermediate Rate Requested |
||||||||
0 |
Establishment: Demand |
||||||||
Octet 5 |
1 |
Extension |
|||||||
0 |
0 |
Access Id |
|||||||
0 |
0 |
Rate Adaptation: No |
|||||||
0 |
0 |
1 |
Signalling Access Protocol: NA |
||||||
Octet 6 |
0 |
Extension |
|||||||
0 |
1 |
Layer 1 Id: Default |
|||||||
0 |
0 |
0 |
0 |
User Information Layer 1 Protocol |
|||||
0 |
Synchronous / Asynchronous: synchronous |
||||||||
Octet 6a |
0 |
Extension |
|||||||
0 |
Number of Stop Bits: NA |
||||||||
0 |
Negotiation: In band Negotiation not possible |
||||||||
1 |
Number of Data Bits: NA |
||||||||
x |
x |
x |
x |
User Rate |
|||||
Octet 6b |
0 |
Extension |
|||||||
1 |
1 |
Intermediate Rate: 16 kbit/s |
|||||||
0 |
NIC on TX: Not Required |
||||||||
0 |
NIC on RX: Not Supported |
||||||||
0 |
1 |
1 |
Parity: NA |
||||||
Octet 6c |
1 |
Extension |
|||||||
x |
x |
Connection Element |
|||||||
0 |
0 |
0 |
0 |
0 |
Modem Type: None |
||||
Octet 7 |
1 |
Extension |
|||||||
1 |
0 |
Layer 2 Id |
|||||||
0 |
0 |
1 |
1 |
0 |
X.25 |
The user rate supported by the MS may have the following values:
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
0 |
1 |
1 |
2,4 kbit/s |
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
0 |
4,8 kbit/s |
NIRR in Octet 4: |
– |
– |
– |
– |
– |
– |
0 |
– |
no meaning |
|
User Rate in Octet 6a: |
– |
– |
– |
– |
0 |
1 |
0 |
1 |
9,6 kbit/s |
If present, Octet 7 shall have the following value:
UI2LP in Octet 7 |
– |
– |
– |
0 |
0 |
1 |
1 |
0 |
X.25 |
11.8.2.8 TS 62 – Automatic Facsimile group 3
The repeat Indicator in the Setup message is not available.
The BC GSM is coded as described in subclause 11.8.2.7.
11.8.2.9 TS 11 and TS 12 – Speech
11.8.2.9.1 Support of only full/half rate speech version 1
The BC in the Setup message is coded as described below.
BC GSM = 04 01 X0
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element : Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
0 |
0 |
0 |
1 |
Length |
Octet 3 |
1 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard : GSM |
||||||||
0 |
Transfer Mode : Circuit |
||||||||
0 |
0 |
0 |
Info. Transfer Cap. : speech |
11.8.2.9.2 Support of speech full rate version 2 (Enhanced Full Rate)
This BC will be used by MS supporting EFR as the most advanced speech version. Those supporting EFR and newer codec speech version such as speech version 3, half rate speech version 2 will not use this BC.
The BC is coded as described below.
BC GSM = 04 0X X0 0X XX (8X)
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element : Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
0 |
x |
x |
x |
Length |
Octet 3 |
0 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard : GSM |
||||||||
0 |
Transfer Mode : Circuit |
||||||||
0 |
0 |
0 |
Info. Transfer Cap. : speech |
||||||
Octet_3a_1 |
0 |
Extension |
|||||||
0 |
Coding |
||||||||
0 |
0 |
Spare |
|||||||
0 |
x |
x |
x |
Speech version indication |
|||||
Octet_3a_2 |
x |
Extension |
|||||||
0 |
Coding |
||||||||
0 |
0 |
Spare |
|||||||
0 |
x |
x |
x |
Speech version indication |
|||||
Octet_3a_3 |
1 |
Extension |
|||||||
0 |
Coding |
||||||||
0 |
0 |
Spare |
|||||||
0 |
x |
x |
x |
Speech version indication |
IF the MS supports only Full Rate:
Octet 2 |
0 |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
Length |
Radio Channel Requirement in Octet 3: |
– |
0 |
1 |
– |
– |
– |
– |
– |
Full rate support only mobile station/preference as in octets3a_etc |
Octet_3a_1 |
– |
– |
– |
– |
– |
0 |
x |
0 |
x=0 : full rate speech version 1 x=1 : full rate speech version 2 |
Octet_3a_2 |
1 |
– |
– |
– |
– |
0 |
x |
0 |
x=0 : full rate speech version 1 x=1 : full rate speech version 2 |
The speech indication in Octet_3a_1 shall be different from the one in Octet_3a_2.
Octet _3a_3 is not present.
ELSE
Octet 2 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Length |
Radio Channel Requirement in Octet 3: |
– |
1 |
x |
– |
– |
– |
– |
– |
x=0 or 1 :Dual rate mobile station/ preference as in octets3a_etc |
Octet_3a_1 |
– |
– |
– |
– |
– |
0 |
x |
x |
(0,0) :full rate speech version 1 (1,0) : full rate speech version 2 (0,1) : half rate speech version 1 |
Octet_3a_2 |
0 |
– |
– |
– |
– |
0 |
x |
x |
(0,0) :full rate speech version 1 (1,0) : full rate speech version 2 ( 0,1) : half rate speech version 1 |
Octet_3a_3 |
1 |
– |
– |
– |
– |
0 |
x |
x |
(0,0) :full rate speech version 1 (1,0) : full rate speech version 2 ( 0,1) : half rate speech version 1 |
Each speech indication in Octet_3a_i shall be different from the one in Octet_3a_j, ij.
11.8.2.9.3 Support of full rate speech version 2 (EFR) and full and/or half rate speech version 3 (AMR)
The BC is coded as described below.
BC GSM: 04 0X X0 0X 0X XX (XX) (8X)
Octet 1 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Information Element : Bearer Capability |
Octet 2 |
0 |
0 |
0 |
0 |
0 |
x |
x |
x |
Length |
Octet 3 |
0 |
Extension |
|||||||
x |
x |
Radio Channel Requirement |
|||||||
0 |
Coding Standard : GSM |
||||||||
0 |
Transfer Mode : Circuit |
||||||||
0 |
0 |
0 |
Info. Transfer Cap. : speech |
||||||
Octet_3a_1 |
0 |
Extension |
|||||||
0 |
Coding |
||||||||
0 |
0 |
Spare |
|||||||
0 |
x |
x |
x |
Speech version indication |
|||||
Octet_3a_2 |
0 |
Extension |
|||||||
0 |
Coding |
||||||||
0 |
0 |
Spare |
|||||||
0 |
x |
x |
x |
Speech version indication |
|||||
Octet_3a_3 |
x |
Extension |
|||||||
0 |
Coding |
||||||||
0 |
0 |
Spare |
|||||||
0 |
x |
x |
x |
Speech version indication |
|||||
Octet_3a_4 |
x |
Extension |
|||||||
0 |
Coding |
||||||||
0 |
0 |
Spare |
|||||||
0 |
x |
x |
x |
Speech version indication |
|||||
Octet_3a_5 |
1 |
Extension |
|||||||
0 |
Coding |
||||||||
0 |
0 |
Spare |
|||||||
0 |
x |
x |
x |
Speech version indication |
IF the MS supports only Full Rate speech version 1 and full rate speech version 2 and full rate speech version 3:
Octet 2 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
0 |
Length |
Radio Channel Requirement in Octet 3: |
– |
0 |
1 |
– |
– |
– |
– |
– |
Full rate support only mobile station/preference as in octets3a_etc |
Octet_3a_1 |
– |
– |
– |
– |
– |
x |
x |
0 |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 |
Octet_3a_2 |
– |
– |
– |
– |
– |
x |
x |
0 |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 |
Octet_3a_3 |
1 |
– |
– |
– |
– |
x |
x |
0 |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 |
Each speech indication in Octet_3a_i shall be different from the one in Octet_3a_j, ij.
ELSE IF the MS supports Full Rate speech version 1 and full rate speech version 2 and full rate speech version 3 and half rate speech version 1
Octet 2 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
1 |
Length |
Radio Channel Requirement in Octet 3: |
– |
1 |
x |
– |
– |
– |
– |
– |
x=0 or 1 :Dual rate mobile station/ preference as in octets3a_etc |
Octet_3a_1 |
– |
– |
– |
– |
– |
x |
x |
x |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 (0,0,1): half rate speech version 1 |
Octet_3a_2 |
– |
– |
– |
– |
– |
x |
x |
x |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 (0,0,1): half rate speech version 1 |
Octet_3a_3 |
0 |
– |
– |
– |
– |
x |
x |
x |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 (0,0,1): half rate speech version 1 |
Octet_3a_4 |
1 |
– |
– |
– |
– |
x |
x |
x |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 (0,0,1): half rate speech version 1 |
Each speech indication in Octet_3a_i shall be different from the one in Octet_3a_j, ij.
ELSE IF the MS supports Full Rate speech version 1 and full rate speech version 2 and full rate speech version 3 and half rate speech version 3
Octet 2 |
0 |
0 |
0 |
0 |
0 |
1 |
0 |
1 |
Length |
Radio Channel Requirement in Octet 3: |
– |
0 |
1 |
– |
– |
– |
– |
– |
Dual rate mobile station/ preference as in octets3a_etc |
Octet_3a_1 |
– |
– |
– |
– |
– |
x |
x |
x |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 (1,0,1): half rate speech version 3 |
Octet_3a_2 |
– |
– |
– |
– |
– |
x |
x |
x |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 (1,0,1): half rate speech version 3 |
Octet_3a_3 |
0 |
– |
– |
– |
– |
x |
x |
x |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 (1,0,1): half rate speech version 3 |
Octet_3a_4 |
1 |
– |
– |
– |
– |
x |
x |
x |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 (1,0,1): half rate speech version 3 |
Each speech indication in Octet_3a_i shall be different from the one in Octet_3a_j, ij.
ELSE IF the MS supports Full Rate speech version 1 and full rate speech version 2 and full rate speech version 3 and half rate speech version 1 and half rate speech version 3.
Octet 2 |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
0 |
Length |
Radio Channel Requirement in Octet 3: |
– |
1 |
x |
– |
– |
– |
– |
– |
x=0 or 1 :Dual rate mobile station/ preference as in octets3a_etc |
Octet_3a_1 |
– |
– |
– |
– |
– |
x |
x |
x |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 (0,0,1): half rate speech version 1 (1,0,1) half rate speech version 3 |
Octet_3a_2 |
– |
– |
– |
– |
– |
x |
x |
x |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 (0,0,1): half rate speech version 1 (1,0,1) half rate speech version 3 |
Octet_3a_3 |
0 |
– |
– |
– |
– |
x |
x |
x |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 (0,0,1): half rate speech version 1 (1,0,1) half rate speech version 3 |
Octet_3a_4 |
0 |
– |
– |
– |
– |
x |
x |
x |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 (0,0,1): half rate speech version 1 (1,0,1) half rate speech version 3 |
Octet_3a_5 |
1 |
– |
– |
– |
– |
x |
x |
x |
(0,0,0): full rate speech version 1 (0,1,0): full rate speech version 2 (1,0,0): full rate speech version 3 (0,0,1): half rate speech version 1 (1,0,1) half rate speech version 3 |
Each speech indication in Octet_3a_i shall be different from the one in Octet_3a_j, ij.3