9.3.6 TDD intra-frequency RSTD Measurement Reporting Delay in CE Mode B
37.571-13GPPPart 1: Conformance test specificationRelease 16TSUser Equipment (UE) conformance specification for UE positioning
9.3.6.1 TDD intra-frequency RSTD Measurement Reporting Delay in CE Mode B for Category M1
9.3.6.1.1 Test purpose
To verify that the RSTD measurement reporting delay for UE Category M1 meets the performance requirements in an environment with fading propagation conditions.
9.3.6.1.2 Test applicability
This test applies to E-UTRA TDD UE Category M1 release 14 and forward that supports UE-assisted OTDOA and CE Mode B.
9.3.6.1.3 Minimum conformance requirements
Same as in clause 9.3.4.1.3.
The intra-frequency requirements in this clause shall apply for all TDD special subframe configurations specified in TS 36.211 [26] and for the TDD uplink-downlink configurations as specified in Table 9.3.6.1.3-1.
Table 9.3.6.1.3-1: TDD uplink-downlink subframe configurations applicable for TDD intra-frequency requirements
PRS Transmission Bandwidth [RB] |
Applicable TDD uplink-downlink configurations |
6 |
1, 2, 3, 4 and 5 |
Note: Uplink-downlink configurations are specified in Table 4.2-2 in TS 36.211 [26]. |
The normative reference for this requirement is TS 36.133 [23] clause 8.13.3.3.2 and A.8.12.8.
9.3.6.1.4 Test description
9.3.6.1.4.1 Initial conditions
Same as in clause 9.3.1.1.4.1 but replacing Table 9.3.1.1.4.1-1 with Table 9.3.6.1.4.1-1
Table 9.3.6.1.4.1-1: General test parameters for E-UTRAN TDD intra-frequency RSTD measurement reporting delay under fading propagation conditions
Parameter |
Unit |
Value |
Comment |
Reference cell |
Cell 1 |
Reference cell is the cell in the OTDOA assistance data with respect to which the RSTD measurement is defined, as specified in 3GPP TS 36.214 [6] and 3GPP TS 36.355 [4]. The reference cell is the serving cell in this test case. |
|
Neighbour cells |
Cell 2 and Cell 3 |
Cell 2 and Cell 3 appear at random places in the neighbour cell list in the OTDOA assistance data, but Cell 2 always appears in the first half of the list, whilst Cell 3 appears in the second half of the list. |
|
MPDCCH |
DL Reference Measurement Channel R.16 TDD |
As specified in TS 36.521-3 [25] clause A.7.3 |
|
mPDCCH-startSF-UESS |
10 |
Parameter G in which determines subframe k0 in which MPDCCH starts |
|
Channel Bandwidth (BWchannel) |
MHz |
10 |
|
PRS Transmission Bandwidth Note 2 |
RB |
50 Note 4 |
PRS are transmitted over the system bandwidth |
PRS configuration index Note 2 |
304 |
This corresponds to periodicity of 320 ms and PRS subframe offset of DL subframes, as defined in 3GPP TS 36.211 [26], Table 6.10.4.3-1 |
|
Number of consecutive downlink positioning subframes Note 2 |
6 |
As defined in 3GPP TS 36.211 [26]. The number of subframes in a positioning occasion |
|
Physical cell ID PCI Note 2 |
(PCI of Cell 1 – PCI of Cell 2)mod6=0 and (PCI of Cell 1 – PCI of Cell 3)mod6=0 |
The cell PCIs are selected such that the relative shifts of PRS patterns among cells are as given by the test parameters |
|
TDD uplink-downlink configuration |
1 |
As specified in TS 36.211 [26], Clause 4.2; corresponds to a configuration with 5 ms switch-point periodicity and two downlink consecutive subframes |
|
TDD special subframe configuration |
6 |
As specified in TS 36.211 [26], Clause 4.2; corresponds to DwPTS of and UpPTS of |
|
CP length Note 2 |
Normal |
||
DRX |
ON |
DRX parameters are further specified in Table 9.3.1.1.4.1-2 |
|
Radio frame receive time offset between the cells at the UE antenna connector Note 3 |
μs |
Cell 2 to Cell 1: 1 Cell 3 to Cell 1: -1 |
PRS are transmitted from synchronous cells |
Expected RSTD Note 1 |
μs |
Cell 2: 3 Cell 3: 3 Other neighbour cells: randomly between -3 and 3 |
The expected RSTD is what is expected at the receiver. The corresponding parameter in the OTDOA assistance data specified in TS 36.355 [4] is the expectedRSTD indicator |
Expected RSTD uncertainty for all neighbour cells Note 1 |
μs |
5 |
The corresponding parameter in the OTDOA assistance data specified in TS 36.355 [4] is the expectedRSTD-Uncertainty index |
Number of cells provided in OTDOA assistance data |
16 |
Including the reference cell |
|
PRS muting info Note 2 |
Cell 1: ‘11110000’ Cell 2: ‘00001111’ Cell 3: ‘11110000’ |
Corresponds to prs-MutingInfo defined in TS 36.355 [4] |
|
T1 |
s |
3 |
The length of the time interval from the beginning of each test |
T2 |
s |
6.4 |
The length of the time interval that follows immediately after time interval T1 |
T3 |
s |
6.4 |
The length of the time interval that follows immediately after time interval T2 |
Note 1: Parameters “Expected RSTD” and “Expected RSTD uncertainty for all neighbour cells” are not settable parameters. These are parameters signalled in LPP only. For the values to be used in LPP see Table 9.3.1.1.4.3-5 and TS 37.571-5 [20], clause 7.2.5. Note 2: Parameters “PRS Transmission Bandwidth”, “PRS configuration index”, “Number of consecutive downlink positioning subframes”, “Physical cell ID PCI”, “CP length”, and “PRS muting info” are settable parameters and also parameters signalled in LPP. The values to be used for “Physical cell ID PCI” are as follows: Cell 1: 0, Cell 2: 6, Cell 3: 12. For all the values to be used in LPP see Table 9.3.1.1.4.3-5 and TS 37.571-5 [20], clause 7.2.5. Note 3: The parameter “Radio frame receive time offset between the cells at the UE antenna connector” is not a settable parameter but is used to set the “true RSTD” values in step 6 of clause 9.3.1.1.4.1. Note 4: If the PRS transmission bandwidth is larger than the UE RF bandwidth, the UE is measuring RSTD within its RF bandwidth. |
9.3.6.1.4.2 Test procedure
Same as in clause 9.3.1.1.4.2 but using condition CEModeB.
9.3.6.1.4.3 Message contents
Same as in clause 9.3.4.1.4.3
9.3.6.1.5 Test requirement
Table 9.3.6.1.5-1 and 9.3.6.1.5-2 define the primary level settings including test tolerances for the test.
Table 9.3.6.1.5-1: Cell-specific test parameters for E-UTRAN TDD intra-frequency RSTD measurement reporting delay under fading propagation conditions during T1
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
E-UTRA RF Channel Number |
1 |
1 |
1 |
|
Correlation Matrix and Antenna Configuration |
1×1 |
1×1 |
1×1 |
|
OCNG patterns defined in TS 36.521-3 [25] clause D.1 |
OP.11 TDD |
N/A |
N/A |
|
PBCH_RA |
dB |
0 |
N/A |
N/A |
PBCH_RB |
||||
PSS_RA |
||||
SSS_RA |
||||
PCFICH_RB |
||||
PHICH_RA |
||||
PHICH_RB |
||||
PDCCH_RA |
||||
PDCCH_RB |
||||
OCNG_RA Note 1 |
||||
OCNG_RB Note 1 |
||||
Note 3 |
dBm/ 15 kHz |
-95 |
||
PRS |
dB |
-Infinity |
-Infinity |
-Infinity |
Io Note 4 |
dBm/ 9 MHz |
-67.22 |
N/A |
N/A |
dB |
0 |
-Infinity |
-Infinity |
|
Propagation Condition |
ETU30 |
|||
Note 1: OCNG shall be used such that active cell (Cell 1) is fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols. Note 2: The resources for uplink transmission are assigned to the UE prior to the start of time period T2. Note 3: Interference from other cells and noise sources not specified in the test are assumed to be constant over subcarriers and time and shall be modelled as AWGN of appropriate power for to be fulfilled. Note 4: Io levels have been derived from other parameters and are given for information purpose. These are not settable test parameters. |
Table 9.3.6.1.5-2: Cell-specific test parameters for E-UTRAN TDD intra-frequency RSTD measurement reporting delay under fading propagation conditions during T2 and T3
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
||||||||
T2 |
T3 |
T2 |
T3 |
T2 |
T3 |
|||||||
E-UTRA RF Channel Number |
1 |
1 |
1 |
|||||||||
Correlation Matrix and Antenna Configuration |
1×1 |
1×1 |
1×1 |
|||||||||
OCNG patterns defined in TS 36.521-3 [25] clause D.1 |
OP.11 TDD |
OP.2 TDD |
OP.2 TDD |
N/A |
||||||||
PBCH_RA |
dB |
0 |
0 |
0 |
N/A |
|||||||
PBCH_RB |
||||||||||||
PSS_RA |
||||||||||||
SSS_RA |
||||||||||||
PCFICH_RB |
||||||||||||
PHICH_RA |
||||||||||||
PHICH_RB |
||||||||||||
PDCCH_RA |
||||||||||||
PDCCH_RB |
||||||||||||
OCNG_RA Note 1 |
||||||||||||
OCNG_RB Note 1 |
||||||||||||
PRS_RA |
dB |
-3 |
N/A |
N/A |
3 |
3 |
N/A |
|||||
Note 3 |
dBm/ 15 kHz |
-98 |
-95 |
-98 |
-95 |
-98 |
-95 |
|||||
PRS |
dB |
-12 |
-Infinity |
-Infinity |
-13 |
-13 |
-Infinity |
|||||
PRS Note 4 |
dB |
-12.21 |
-Infinity |
-Infinity |
-13 |
-13.27 |
-Infinity |
|||||
Io Note 4 |
dBm/ 9 MHz |
-69.92 |
-67.18 |
-69.92 |
-67.18 |
-69.92 |
-67.18 |
|||||
PRP Note 4 |
dBm/ 15 kHz |
-110 |
-Infinity |
-Infinity |
-108 |
-111 |
-Infinity |
|||||
RSRP Note 4 |
dBm/ 15 kHz |
-107 |
-104 |
-111 |
-111 |
-114 |
-Infinity |
|||||
Note 4 |
dB |
-9 |
-9 |
-13 |
-16 |
-16 |
-Infinity |
|||||
Propagation Condition |
ETU30 |
|||||||||||
Note 1: OCNG shall be used such that active cells (all, except Cell 3 in T3) are fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols other than those in the subframes with transmitted PRS. Note 2: The resources for uplink transmission are assigned to the UE prior to the start of time period T2. Note 3: Interference from other cells and noise sources not specified in the test are assumed to be constant over subcarriers and time and shall be modelled as AWGN of appropriate power for to be fulfilled. Note 4: If PRS_RA is not “N/A”,, PRS , Io, RSRP and PRP levels have been derived from other parameters and are given for information purpose. If PRS_RA is “N/A”, Io and RSRP levels have been derived from other parameters and are given for information purpose. These are not settable test parameters. Interference conditions shall be applied to all PRS symbols of DL positioning subframes. |
The response time is defined in clause 9.3.4.1.5.
The test tolerances are defined in clauses C.1.3 and C4.
The rate of successful tests during repeated tests shall be at least 90% with a confidence level of 95%.
9.3.6.2 TDD intra-frequency RSTD Measurement Reporting Delay in CE Mode B for Category M2
9.3.6.2.1 Test purpose
To verify that the RSTD measurement reporting delay for UE Category M2 meets the performance requirements in an environment with fading propagation conditions.
9.3.6.2.2 Test applicability
This test applies to E-UTRA TDD UE Category M2 release 14 and forward that supports UE-assisted OTDOA and CE Mode B.
9.3.6.2.3 Minimum conformance requirements
Same as in clause 9.3.6.1.3.
The intra-frequency requirements in this clause shall apply for all TDD special subframe configurations specified in TS 36.211 [26] and for the TDD uplink-downlink configurations as specified in Table 9.3.6.2.3-1.
Table 9.3.6.2.3-1: TDD uplink-downlink subframe configurations applicable for TDD intra-frequency requirements
PRS Transmission Bandwidth [RB] |
Applicable TDD uplink-downlink configurations |
6 |
1, 2, 3, 4 and 5 |
24 |
0, 1, 2, 3, 4, 5 and 6 |
Note: Uplink-downlink configurations are specified in Table 4.2-2 in TS 36.211 [26]. |
The normative reference for this requirement is TS 36.133 [23] clause 8.16.3.1.2 and A.8.12.8.
9.3.6.2.4 Test description
9.3.6.2.4.1 Initial conditions
Same as in clause 9.3.1.1.4.1 but replacing Table 9.3.1.1.4.1-1 with Table 9.3.6.2.4.1-1.
Table 9.3.6.2.4.1-1: General test parameters for E-UTRAN TDD intra-frequency RSTD measurement reporting delay under fading propagation conditions
Parameter |
Unit |
Value |
Comment |
|
Test 1 |
Test 2 |
|||
Reference cell |
Cell 1 |
Reference cell is the cell in the OTDOA assistance data with respect to which the RSTD measurement is defined, as specified in 3GPP TS 36.214 [6] and 3GPP TS 36.355 [4]. The reference cell is the serving cell in this test case. |
||
Neighbour cells |
Cell 2 and Cell 3 |
Cell 2 and Cell 3 appear at random places in the neighbour cell list in the OTDOA assistance data, but Cell 2 always appears in the first half of the list, whilst Cell 3 appears in the second half of the list. |
||
MPDCCH |
DL Reference Measurement Channel R.16 TDD |
As specified in TS 36.521-3 [25] clause A.7.3 |
||
mPDCCH-startSF-UESS |
10 |
Parameter G in which determines subframe k0 in which MPDCCH starts |
||
Channel Bandwidth (BWchannel) |
MHz |
10 |
||
PRS Transmission Bandwidth Note 2 |
RB |
50 Note 4 |
PRS are transmitted over the system bandwidth |
|
PRS configuration index Note 2 |
304 |
This corresponds to periodicity of 320 ms and PRS subframe offset of DL subframes, as defined in 3GPP TS 36.211 [26], Table 6.10.4.3-1 |
||
Number of consecutive downlink positioning subframes Note 2 |
6 |
4 |
As defined in 3GPP TS 36.211 [26]. The number of subframes in a positioning occasion |
|
Physical cell ID PCI Note 2 |
(PCI of Cell 1 – PCI of Cell 2)mod6=0 and (PCI of Cell 1 – PCI of Cell 3)mod6=0 |
The cell PCIs are selected such that the relative shifts of PRS patterns among cells are as given by the test parameters |
||
TDD uplink-downlink configuration |
1 |
As specified in TS 36.211 [26], Clause 4.2; corresponds to a configuration with 5 ms switch-point periodicity and two downlink consecutive subframes |
||
TDD special subframe configuration |
6 |
As specified in TS 36.211 [26], Clause 4.2; corresponds to DwPTS of and UpPTS of |
||
CP length Note 2 |
Normal |
|||
DRX |
ON |
DRX parameters are further specified in Table 9.3.1.1.4.1-2 |
||
Radio frame receive time offset between the cells at the UE antenna connector Note 3 |
μs |
Cell 2 to Cell 1: 1 Cell 3 to Cell 1: -1 |
PRS are transmitted from synchronous cells |
|
Expected RSTD Note 1 |
μs |
Cell 2: 3 Cell 3: 3 Other neighbour cells: randomly between -3 and 3 |
The expected RSTD is what is expected at the receiver. The corresponding parameter in the OTDOA assistance data specified in TS 36.355 [4] is the expectedRSTD indicator |
|
Expected RSTD uncertainty for all neighbour cells Note 1 |
μs |
5 |
The corresponding parameter in the OTDOA assistance data specified in TS 36.355 [4] is the expectedRSTD-Uncertainty index |
|
Number of cells provided in OTDOA assistance data |
16 |
Including the reference cell |
||
PRS muting info Note 2 |
Cell 1: ‘11110000’ Cell 2: ‘00001111’ Cell 3: ‘11110000’ |
Corresponds to prs-MutingInfo defined in TS 36.355 [4] |
||
T1 |
s |
3 |
The length of the time interval from the beginning of each test |
|
T2 |
s |
6.4 |
2.56 |
The length of the time interval that follows immediately after time interval T1 |
T3 |
s |
6.4 |
2.56 |
The length of the time interval that follows immediately after time interval T2 |
Note 1: Parameters “Expected RSTD” and “Expected RSTD uncertainty for all neighbour cells” are not settable parameters. These are parameters signalled in LPP only. For the values to be used in LPP see Table 9.3.1.1.4.3-5 and TS 37.571-5 [20], clause 7.2.5. Note 2: Parameters “PRS Transmission Bandwidth”, “PRS configuration index”, “Number of consecutive downlink positioning subframes”, “Physical cell ID PCI”, “CP length”, and “PRS muting info” are settable parameters and also parameters signalled in LPP. The values to be used for “Physical cell ID PCI” are as follows: Cell 1: 0, Cell 2: 6, Cell 3: 12. For all the values to be used in LPP see Table 9.3.1.1.4.3-5 and TS 37.571-5 [20], clause 7.2.5. Note 3: The parameter “Radio frame receive time offset between the cells at the UE antenna connector” is not a settable parameter but is used to set the “true RSTD” values in step 6 of clause 9.3.1.1.4.1. Note 4: If the PRS transmission bandwidth is larger than the UE RF bandwidth, the UE is measuring RSTD within its RF bandwidth. |
9.3.6.2.4.2 Test procedure
Same as in clause 9.3.1.1.4.2 but using condition CEModeB and with the following additional step:
14. Repeat step 1-13 for each sub-test in Table 9.3.2.2.4.1-1 as appropriate.
9.3.6.2.4.3 Message contents
Same as in clause 9.3.4.2.4.3.
9.3.6.2.5 Test requirement
The primary level settings including test tolerances for the test are defined in clause 9.3.6.1.5.
For Test 1, the response time is defined in clause 9.3.6.1.5.
For Test 2, the response time including test tolerance is 6.3 s. The response time is equal to the LPP time IE value plus the test tolerance. The LPP time IE value is derived from the RSTD reporting delay plus ΔT, where ΔT = Nrepx TTIDCCH = Nrepx 75 ms, giving a value of 5270 ms. This is rounded up to the next allowed LPP value of 6 seconds. The RSTD measurement reporting delay in the test is derived from the following expression , where =40 and =16 are the parameters specified in clause 9.3.1.1.3, Table 9.3.1.1.3‑1 and Note 4 of Table 9.3.6.2.4.1-1. This gives the total RSTD reporting delay of 5210 ms for the 15 neighbour cells including Cell 2 and Cell 3 with respect to the reference cell, Cell 1.
The test tolerances are defined in clauses C.1.3 and C4.
For the overall test to pass, the ratio of successful reported values in each sub-test shall be more than 90% with a confidence level of 95%.9.3.7 FDD intra-frequency RSTD Measurement Accuracy in CE Mode A.