F.2 UTRAN connection set up
37.571-13GPPPart 1: Conformance test specificationRelease 16TSUser Equipment (UE) conformance specification for UE positioning
F.2.1 Initial conditions
System Simulator:
– 1 cell, default parameters. The default system information, as specified in clause 6.1 of TS 34.108 [28], is broadcast with the exceptions of SIB15, SIB15.1, SIB15.2 and SIB15.3 which are not broadcast.
User Equipment:
– The UE shall be operated in Normal Propagation Conditions as specified in clause 5.2.1 of TS 34.108 [28].
– The UE is in state "MM idle" state with valid TMSI and CKSN.
– The UE is in state "PMM idle" with valid P-TMSI.
F.2.2 Procedures
CS Domain
Step |
Direction |
Message |
Comments |
|
UE |
SS |
|||
1 |
<– |
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
2 |
<– |
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
3 |
–> |
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
4 |
<– |
RRC CONNECTION SETUP (CCCH) |
RRC |
|
5 |
–> |
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
6 |
–> |
PAGING RESPONSE |
RR |
|
7 |
<– |
AUTHENTICATION REQUEST |
MM |
|
8 |
–> |
AUTHENTICATION RESPONSE |
MM |
|
9 |
<– |
SECURITY MODE COMMAND |
RRC |
|
10 |
–> |
SECURITY MODE COMPLETE |
RRC |
PS Domain
Step |
Direction |
Message |
Comments |
|
UE |
SS |
|||
1 |
<– |
PAGING TYPE1 (PCCH) |
Paging (PS domain, PMSI or IMSI) |
|
2 |
–> |
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
3 |
<– |
RRC CONNECTION SETUP (CCCH) |
RRC |
|
4 |
–> |
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC (Transport Channel: DCH or FACH) |
|
5 |
–> |
SERVICE REQUEST |
GMM |
|
6 |
<– |
AUTHENTICATION REQUEST |
GMM |
|
7 |
–> |
AUTHENTICATION RESPONSE |
GMM |
|
8 |
<– |
SECURITY MODE COMMAND |
RRC |
|
9 |
–> |
SECURITY MODE COMPLETE |
RRC |
F.2.3 Specific message contents
The default message contents specified in clause 9.1 of TS 34.108 [28] will be used for the Moving Scenario and Periodic Update test. For all Minimum Performance TTFF Tests the default message contents specified in clause 9.1 of TS 34.108 [28] will be used with the following exception.
Contents of PAGING TYPE1:
Information Element |
Value/remark |
Paging Cause |
Terminating High Priority Signalling |
Contents of RRC CONNECTION SETUP:
For A-GNSS performance testing in CELL_DCH state: The RRC Connection Setup is defined in clause 9.1.1 of TS 34.108 [28] "Contents of RRC CONNECTION SETUP message: UM (Transition to CELL_DCH)".
For A-GNSS performance testing in CELL_FACH state: The RRC Connection Setup is defined in clause 9.1.1 of TS 34.108 [28] "Contents of RRC CONNECTION SETUP message: UM (Transition to CELL_FACH)".
Contents of RRC CONNECTION SETUP COMPLETE:
Information Element |
Value/remark |
UE radio access capability |
|
– UE positioning capability |
Defines the A-GNSS mode the UE supports (UE-based, UE-assisted, or both). UE shall be tested for all modes it supports. |