Test 1

Test 2

PCFICH/PDCCH/PHICH parameters

R.14 FDD

R.6 FDD

As specified in TS 36.521-3 [25] clause A.2.1.

OCNG Patterns defined in TS 36.521-3 [25] clause D.1

OP.7 FDD

OP.6 FDD

OCNG shall be used such that both cells are fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols (other than those in the PRS subframes).

Reference cell

Cell 1

Cell 1 on RF channel number 1

Neighbour cell

Cell 2

Cell 2 on RF channel number 2

E-UTRA RF Channel Number

1,2

Two FDD carrier frequencies are used.

Channel Bandwidth (BW_channel)

MHz

1.4

10

GapOffset

18

11

For Cell 1

Gap Pattern ID

0

0

For Cell 1

PRS Bandwidth

RB

6

50

PRS configuration Index ^{Note 2}

Cell 1: 12

Cell 2: 19

Cell 1: 2

Cell 2: 12

As defined in 3GPP TS 36.211 [26]

PRS subframe offset

7

10

For Cell 2

Number of consecutive positioning downlink subframes ^{Note 2}

6

1

As defined in 3GPP TS 36.211 [26]

prs-MutingInfo ^{Note 2}

Cell 1: ‘1111111100000000’

Cell 2: ‘1111111100000000’

See section 6.5.1.2 in 3GPP TS 36.355 [4] for more information

Cell ID^{Note 2}

Cell 1: 0

Cell 2: 1

Expected RSTD^{Note 1}

μs

Cell 2: 1

Other neighbour cells: randomly between -3 and 3

The expected RSTD is what is expected at the receiver. The corresponding parameter in the OTDOA assistance data specified in TS 36.355 [4] is the expectedRSTD indicator

Expected RSTD uncertainty for all neighbour cells ^{Note 1}

μs

5

The corresponding parameter in the OTDOA assistance data specified in TS 36.355 [4] is the expectedRSTD-Uncertainty index

CP length ^{Note 2}

Normal

DRX

OFF

Radio frame receive time offset between the cells at the UE antenna connector ^{Note 3}

μs

Cell 2 to Cell 1: 3

Cell 2 to Cell 1: -3

PRS are transmitted from synchronous cells

Number of cells provided in OTDOA assistance data

16

The list includes the reference cell (received in OTDOA-ReferenceCellInfo [4]) on RF channel 1 and 15 other cells on RF channel 2, all received in OTDOA-ProvideAssistanceData [4].

^{Note 4}

ms

10240

Derived according to the RSTD measurement requirements specified in Section 8.1.2.6.5 in TS 36.133 [23].

NOTE 1: Parameters “Expected RSTD” and “Expected RSTD uncertainty for all neighbour cells” in Table 9.2.4.4.1-1 are not settable parameters. These are parameters signalled in LPP only. For the values to be used in LPP see Table 9.2.4.4.3-4 and TS 37.571-5 [20], clause 7.2.2.

NOTE 2: Parameters “PRS Bandwidth”, “PRS configuration index”, “Number of consecutive positioning downlink subframes”, “prs-MutingInfo”, “Cell ID” and “CP length” in Table 9.2.4.4.1-1 are settable parameters and also parameters signalled in LPP. For all the values to be used in LPP see Table 9.2.4.4.3-4 and TS 37.571-5 [20], clause 7.2.2.

NOTE 3: The parameter “Radio frame receive time offset between the cells at the UE antenna connector” is not a settable parameter but is used to set the “true RSTD” values in step 6 of clause 9.2.4.4.1.

NOTE 4: The parameter “” is not a settable parameter but is used to set the LPP “time” value in Table 9.2.4.4.3-3. The value of the LPP time IE is set to + T ms, where T = 150 ms, giving a value of 10390 ms. This is rounded up to the next allowed LPP value of 11 seconds.

Information Element

Value/remark

Comment

Condition

LPP-Message ::= SEQUENCE {

lpp-MessageBody CHOICE {

c1 CHOICE {

requestLocationInformation SEQUENCE {

criticalExtensions CHOICE {

c1 CHOICE {

requestLocationInformation-r9 SEQUENCE {

commonIEsRequestLocationInformation

SEQUENCE {

qos SEQUENCE {

responseTime SEQUENCE {

time

11

See Note 4 of Table 9.2.4A.4.1-1

}

}

}

}

}

}

}

}

}

}