9.3.5 HD-FDD intra-frequency RSTD Measurement Reporting Delay in CE Mode B

37.571-13GPPPart 1: Conformance test specificationRelease 16TSUser Equipment (UE) conformance specification for UE positioning

9.3.5.1 HD-FDD intra-frequency RSTD Measurement Reporting Delay in CE Mode B for Category M1

9.3.5.1.1 Test purpose

To verify that the RSTD measurement reporting delay for UE Category M1 meets the performance requirements in an environment with fading propagation conditions.

9.3.5.1.2 Test applicability

This test applies to E-UTRA HD-FDD UE Category M1 release 14 and forward that supports UE-assisted OTDOA and CE Mode B.

9.3.5.1.3 Minimum conformance requirements

Same as in clause 9.3.4.1.3.

The normative reference for this requirement is TS 36.133 [23] clause 8.13.3.3.3 and A.8.12.7.

9.3.5.1.4 Test description

9.3.5.1.4.1 Initial conditions

Same as in clause 9.3.1.1.4.1 but replacing Table 9.3.1.1.4.1-1 with Table 9.3.5.1.4.1-1

Table 9.3.5.1.4.1-1: General test parameters for E-UTRAN HD-FDD intra-frequency RSTD measurement reporting delay under fading propagation conditions

Parameter

Unit

Value

Comment

Reference cell

Cell 1

Reference cell is the cell in the OTDOA assistance data with respect to which the RSTD measurement is defined, as specified in 3GPP TS 36.214 [6] and 3GPP TS 36.355 [4]. The reference cell is the serving cell in this test case.

Neighbour cells

Cell 2 and Cell 3

Cell 2 and Cell 3 appear at random places in the neighbour cell list in the OTDOA assistance data, but Cell 2 always appears in the first half of the list, whilst Cell 3 appears in the second half of the list.

MPDCCH

DL Reference Measurement Channel R.8 HD-FDD

As specified in TS 36.521-3 [25] clause A.7.2

mPDCCH-startSF-UESS

10

Parameter G in which determines subframe k0 in which MPDCCH starts

Channel Bandwidth (BWchannel)

MHz

10

PRS Transmission Bandwidth Note 2

RB

50 Note 4

PRS are transmitted over the system bandwidth

PRS configuration index Note 2

311

This corresponds to periodicity of 320 ms and PRS subframe offset of DL subframes, as defined in 3GPP TS 36.211 [26], Table 6.10.4.3-1

Number of consecutive downlink positioning subframes Note 2

6

As defined in 3GPP TS 36.211 [26]. The number of subframes in a positioning occasion

Physical cell ID PCI Note 2

(PCI of Cell 1 – PCI of Cell 2)mod6=0

and

(PCI of Cell 1 – PCI of Cell 3)mod6=0

The cell PCIs are selected such that the relative shifts of PRS patterns among cells are as given by the test parameters

CP length Note 2

Normal

DRX

ON

DRX parameters are further specified in Table 9.3.1.1.4.1-2

Radio frame receive time offset between the cells at the UE antenna connector Note 3

μs

Cell 2 to Cell 1: 1

Cell 3 to Cell 1: -1

PRS are transmitted from synchronous cells

Expected RSTD Note 1

μs

Cell 2: 3

Cell 3: 3

Other neighbour cells: randomly between -3 and 3

The expected RSTD is what is expected at the receiver. The corresponding parameter in the OTDOA assistance data specified in TS 36.355 [4] is the expectedRSTD indicator

Expected RSTD uncertainty for all neighbour cells Note 1

μs

5

The corresponding parameter in the OTDOA assistance data specified in TS 36.355 [4] is the expectedRSTD-Uncertainty index

Number of cells provided in OTDOA assistance data

16

Including the reference cell

PRS muting info Note 2

Cell 1: ‘11110000’

Cell 2: ‘00001111’

Cell 3: ‘11110000’

Corresponds to prs-MutingInfo defined in TS 36.355 [4]

T1

s

3

The length of the time interval from the beginning of each test

T2

s

6.4

The length of the time interval that follows immediately after time interval T1

T3

s

6.4

The length of the time interval that follows immediately after time interval T2

Note 1: Parameters “Expected RSTD” and “Expected RSTD uncertainty for all neighbour cells” are not settable parameters. These are parameters signalled in LPP only. For the values to be used in LPP see Table 9.3.1.1.4.3-5 and TS 37.571-5 [20], clause 7.2.5.

Note 2: Parameters “PRS Transmission Bandwidth”, “PRS configuration index”, “Number of consecutive downlink positioning subframes”, “Physical cell ID PCI”, “CP length”, and “PRS muting info” are settable parameters and also parameters signalled in LPP. The values to be used for “Physical cell ID PCI” are as follows: Cell 1: 0, Cell 2: 6, Cell 3: 12. For all the values to be used in LPP see Table 9.3.1.1.4.3-5 and TS 37.571-5 [20], clause 7.2.5.

Note 3: The parameter “Radio frame receive time offset between the cells at the UE antenna connector” is not a settable parameter but is used to set the “true RSTD” values in step 6 of clause 9.3.1.1.4.1.

Note 4: If the PRS transmission bandwidth is larger than the UE RF bandwidth, the UE is measuring RSTD within its RF bandwidth.

9.3.5.1.4.2 Test procedure

Same as in clause 9.3.1.1.4.2 but using condition CEModeB.

9.3.5.1.4.3 Message contents

Same as in clause 9.3.4.1.4.3

9.3.5.1.5 Test requirement

Same as in clause 9.3.4.1.5.

9.3.5.2 HD-FDD intra-frequency RSTD Measurement Reporting Delay in CE Mode B for Category M2

9.3.5.2.1 Test purpose

To verify that the RSTD measurement reporting delay for UE Category M2 meets the performance requirements in an environment with fading propagation conditions.

9.3.5.2.2 Test applicability

This test applies to E-UTRA HD-FDD UE Category M2 release 14 and forward that supports UE-assisted OTDOA and CE Mode B.

9.3.5.2.3 Minimum conformance requirements

Same as in clause 9.3.4.1.3.

The normative reference for this requirement is TS 36.133 [23] clause 8.16.3.1.3 and A.8.12.7.

9.3.5.2.4 Test description

9.3.5.2.4.1 Initial conditions

Same as in clause 9.3.1.1.4.1 but replacing Table 9.3.1.1.4.1-1 with Table 9.3.5.2.4.1-1.

Table 9.3.5.2.4.1-1: General test parameters for E-UTRAN HD-FDD intra-frequency RSTD measurement reporting delay under fading propagation conditions

Parameter

Unit

Value

Comment

Test 1

Test 2

Reference cell

Cell 1

Reference cell is the cell in the OTDOA assistance data with respect to which the RSTD measurement is defined, as specified in 3GPP TS 36.214 [6] and 3GPP TS 36.355 [4]. The reference cell is the serving cell in this test case.

Neighbour cells

Cell 2 and Cell 3

Cell 2 and Cell 3 appear at random places in the neighbour cell list in the OTDOA assistance data, but Cell 2 always appears in the first half of the list, whilst Cell 3 appears in the second half of the list.

MPDCCH

DL Reference Measurement Channel R.8 HD-FDD

As specified in TS 36.521-3 [25] clause A.7.2

mPDCCH-startSF-UESS

10

Parameter G in which determines subframe k0 in which MPDCCH starts

Channel Bandwidth (BWchannel)

MHz

10

PRS Transmission Bandwidth Note 2

RB

50 Note 4

PRS are transmitted over the system bandwidth

PRS configuration index Note 2

311

This corresponds to periodicity of 320 ms and PRS subframe offset of DL subframes, as defined in 3GPP TS 36.211 [26], Table 6.10.4.3-1

Number of consecutive downlink positioning subframes Note 2

6

4

As defined in 3GPP TS 36.211 [26]. The number of subframes in a positioning occasion

Physical cell ID PCI Note 2

(PCI of Cell 1 – PCI of Cell 2)mod6=0

and

(PCI of Cell 1 – PCI of Cell 3)mod6=0

The cell PCIs are selected such that the relative shifts of PRS patterns among cells are as given by the test parameters

CP length Note 2

Normal

DRX

ON

DRX parameters are further specified in Table 9.3.1.1.4.1-2

Radio frame receive time offset between the cells at the UE antenna connector Note 3

μs

Cell 2 to Cell 1: 1

Cell 3 to Cell 1: -1

PRS are transmitted from synchronous cells

Expected RSTD Note 1

μs

Cell 2: 3

Cell 3: 3

Other neighbour cells: randomly between -3 and 3

The expected RSTD is what is expected at the receiver. The corresponding parameter in the OTDOA assistance data specified in TS 36.355 [4] is the expectedRSTD indicator

Expected RSTD uncertainty for all neighbour cells Note 1

μs

5

The corresponding parameter in the OTDOA assistance data specified in TS 36.355 [4] is the expectedRSTD-Uncertainty index

Number of cells provided in OTDOA assistance data

16

Including the reference cell

PRS muting info Note 2

Cell 1: ‘11110000’

Cell 2: ‘00001111’

Cell 3: ‘11110000’

Corresponds to prs-MutingInfo defined in TS 36.355 [4]

T1

s

3

The length of the time interval from the beginning of each test

T2

s

6.4

2.56

The length of the time interval that follows immediately after time interval T1

T3

s

6.4

2.56

The length of the time interval that follows immediately after time interval T2

Note 1: Parameters “Expected RSTD” and “Expected RSTD uncertainty for all neighbour cells” are not settable parameters. These are parameters signalled in LPP only. For the values to be used in LPP see Table 9.3.1.1.4.3-5 and TS 37.571-5 [20], clause 7.2.5.

Note 2: Parameters “PRS Transmission Bandwidth”, “PRS configuration index”, “Number of consecutive downlink positioning subframes”, “Physical cell ID PCI”, “CP length”, and “PRS muting info” are settable parameters and also parameters signalled in LPP. The values to be used for “Physical cell ID PCI” are as follows: Cell 1: 0, Cell 2: 6, Cell 3: 12. For all the values to be used in LPP see Table 9.3.1.1.4.3-5 and TS 37.571-5 [20], clause 7.2.5.

Note 3: The parameter “Radio frame receive time offset between the cells at the UE antenna connector” is not a settable parameter but is used to set the “true RSTD” values in step 6 of clause 9.3.1.1.4.1.

Note 4: If the PRS transmission bandwidth is larger than the UE RF bandwidth, the UE is measuring RSTD within its RF bandwidth.

9.3.5.2.4.2 Test procedure

Same as in clause 9.3.1.1.4.2 but using condition CEModeB and with the following additional step:

14. Repeat step 1-13 for each sub-test in Table 9.3.2.2.4.1-1 as appropriate.

9.3.5.2.4.3 Message contents

Same as in clause 9.3.4.2.4.3.

9.3.5.2.5 Test requirement

Same as in clause 9.3.4.2.5.

For the overall test to pass, the ratio of successful reported values in each sub-test shall be more than 90% with a confidence level of 95%.