15.2.2 UE Rx-Tx time difference measurement period for dual positioning frequency layer in FR1 SA
37.571-13GPPPart 1: Conformance test specificationRelease 16TSUser Equipment (UE) conformance specification for UE positioning
15.2.2.1 Test purpose
The purpose of the test is to verify that the UE Rx-Tx measurement period meets the requirements specified in TS 38.133 [50] clause 9.9.4.5 in AWGN propagation condition in FR1 in standalone scenario when dual positioning frequency layers are configured.
15.2.2.2 Test applicability
This test applies to all types of NR UE release 16 onwards that supports Multi-RTT positioning.
15.2.2.3 Minimum conformance requirements
Same as defined in clause 15.2.1.3.
15.2.2.4 Test description
The test defines three possible test configurations; specified in Table 15.2.2.4-1. The UE is only required to be tested in one of the supported test configurations.
Table 15.2.2.4-1: Test Configurations
Test Configuration |
Description |
1 |
15 kHz SSB SCS, 10 MHz bandwidth, FDD duplex mode |
2 |
15 kHz SSB SCS, 10 MHz bandwidth, TDD duplex mode |
3 |
30 kHz SSB SCS, 40 MHz bandwidth, TDD duplex mode |
Note: The UE is only required to be tested in one of the supported test configurations. |
15.2.2.4.1 Initial conditions
Test Environment: Normal, as defined in TS 38.508-1 [45] clause 4.1.
Frequencies to be tested: Low Range for Cell 1 and High Range for Cell2, as defined in TS 38.508-1 [45] clause 4.3.1.
Channel bandwidth to be tested: are specified in Table 15.2.2.4-1.
1. Connect the SS and AWGN noise sources to the UE antenna connector or antenna connectors as shown in Annex A, Figure A.13.
2. The general test parameter settings are set up according to Table 15.2.2.5-1 and Table 15.2.2.5-2.
3. Propagation conditions are set according to clause 4.14.2.
4. Message contents are defined in clause 15.2.2.4.3.
5. There are two cells in the test: PCell (Cell 1) and a neighbour cell (Cell 2). Cell 1 and Cell2 are on different RF channels in FR1.
15.2.2.4.2 Test procedure
Same as defined in clause 15.2.1.4.2.
15.2.2.4.3 Message contents
Table 15.2.2.4.3-1: RESET UE POSITIONING STORED INFORMATION
Derivation Path: 38.509 [44] clause 6.6 |
|||
Information Element |
Value/remark |
Comment |
Condition |
UE Positioning Technology |
0 0 0 0 0 1 1 0 |
Multi-RTT |
Table 15.2.2.4.3-2: RRCReconfiguration
Derivation Path: TS 38.508-1 [45],, table 4.6.1-13 |
||||
Information Element |
Value/remark |
Comment |
Condition |
|
RRCReconfiguration ::= SEQUENCE { |
||||
criticalExtensions CHOICE { |
||||
rrcReconfiguration SEQUENCE { |
||||
radioBearerConfig |
||||
nonCriticalExtension SEQUENCE { |
||||
masterCellGroup SEQUENCE { |
CellGroupConfig |
|||
spCellConfig SEQUENCE { |
||||
spCellConfigDedicated SEQUENCE { |
||||
uplinkConfig SEQUENCE { |
||||
initialUplinkBWP SEQUENCE { |
||||
srs-Config CHOICE { |
||||
setup |
As defined in Table 15.2.2.4.3-3 |
|||
} |
||||
} |
||||
} |
||||
} |
||||
} |
||||
} |
||||
} |
||||
} |
||||
} |
||||
} |
Table 15.2.2.4.3-3: SRS-Config (Table 15.2.1.4.3-2)
Derivation Path: TS 38.508-1 [45], Table 4.6.3-182 |
|||
Information Element |
Value/remark |
Comment |
Condition |
SRS-Config ::= SEQUENCE { |
|||
srs-ResourceSetToReleaseList |
Not present |
||
srs-ResourceSetToAddModList |
Not present |
||
srs-ResourceToReleaseList |
Not present |
||
srs-ResourceToAddModList |
Not present |
||
tpc-Accumulation |
Not present |
||
srs-RequestDCI-1-2-r16 |
Not present |
||
srs-RequestDCI-0-2-r16 |
Not present |
||
srs-ResourceSetToAddModListDCI-0-2-r16 |
Not present |
||
srs-ResourceSetToReleaseListDCI-0-2-r16 |
Not present |
||
srs-PosResourceSetToReleaseList-r16 |
Not present |
||
srs-PosResourceSetToAddModList-r16 SEQUENCE (SIZE(1..maxNrofSRS-PosResourceSets-r16)) OF SRS-PosResourceSet-r16 { |
1 entry |
||
SRS-PosResourceSet-r16[1] SEQUENCE { |
entry 1 |
||
srs-PosResourceSetId-r16 |
0 |
||
srs-PosResourceIdList-r16 SEQUENCE (SIZE(1..maxNrofSRS-ResourcesPerSet)) OF SRS-PosResourceId-r16 { |
1 entry |
||
SRS-PosResourceId-r16 |
0 |
1 entry |
|
} |
|||
resourceType CHOICE { |
|||
periodic SEQUENCE { |
|||
} |
|||
} |
|||
alpha-r16 |
alpha0 |
||
p0-r16 |
0 |
||
pathlossReferenceRS-Pos-r16 |
Not present |
||
} |
|||
srs-PosResourceToReleaseList-r16 |
Not present |
||
srs-PosResourceToAddModList-r16 SEQUENCE (SIZE(1..maxNrofSRS-PosResources-r16)) OF SRS-PosResource-r16 { |
1 entry |
||
SRS-PosResource-r16[1] SEQUENCE { |
entry 1 |
||
srs-PosResourceId-r16 |
0 |
||
transmissionComb-r16 CHOICE { |
|||
n4-r16 SEQUENCE { |
|||
combOffset-n4-r16 |
0 |
||
cyclicShift-n4-r16 |
0 |
||
} |
|||
} |
|||
resourceMapping-r16 SEQUENCE { |
|||
startPosition-r16 |
0 |
||
nrofSymbols-r16 |
n4 |
||
} |
|||
freqDomainShift-r16 |
0 |
||
freqHopping-r16 SEQUENCE { |
|||
c-SRS-r16 |
Matches NRB,c Table 15.2.2.5-1 |
||
} |
|||
groupOrSequenceHopping-r16 |
neither |
||
resourceType-r16 CHOICE { |
|||
periodic-r16 SEQUENCE { |
|||
periodicityAndOffset-p-r16 CHOICE { |
|||
sl160 |
20 |
Configuration 1 and Configuration 2 |
|
sl320 |
40 |
Configuration 3 |
|
} |
|||
} |
|||
} |
|||
sequenceId-r16 |
0 |
||
spatialRelationInfoPos-r16 |
Not present |
||
} |
|||
} |
|||
} |
Table 15.2.2.4.3-4: LPP Request Capabilities
Information Element |
Value/remark |
nr-Multi-RTT-RequestCapabilities-r16 |
TRUE |
Table 15.2.2.4.3-5: LPP RequestLocationInformation
Derivation Path: 37.355 clause 6.2 |
|||
Information Element |
Value/remark |
Comment |
Condition |
LPP-Message ::= SEQUENCE { |
|||
transactionID SEQUENCE { |
|||
initiator |
locationServer |
||
transactionNumber |
1 |
||
} |
|||
endTransaction |
FALSE |
||
sequenceNumber |
Not present |
||
acknowledgement |
Not present |
||
lpp-MessageBody CHOICE { |
|||
c1 CHOICE { |
|||
requestLocationInformation SEQUENCE { |
|||
criticalExtensions CHOICE { |
|||
c1 CHOICE { |
|||
requestLocationInformation-r9 SEQUENCE { |
|||
commonIEsRequestLocationInformation SEQUENCE { |
|||
locationInformationType |
locationMeasurementsRequired |
||
triggeredReporting |
Not present |
||
periodicalReporting |
Not present |
||
additionalInformation |
onlyReturnInformationRequested |
||
qos SEQUENCE { |
|||
horizontalAccuracy |
Not present |
||
verticalCoordinateRequest |
FALSE |
||
verticalAccuracy |
Not present |
||
responseTime SEQUENCE { |
|||
time |
20 |
||
responseTimeEarlyFix-r12 |
Not present |
Rel-12 onwards |
|
} |
|||
velocityRequest |
FALSE |
||
} |
|||
environment |
Not present |
||
locationCoordinateTypes |
Not present |
||
velocityTypes |
Not present |
||
} |
|||
a-gnss-RequestLocationInformation |
Not present |
||
otdoa-RequestLocationInformation |
Not present |
||
ecid-RequestLocationInformation |
Not present |
||
epdu-RequestLocationInformation |
Not Present |
||
sensor-RequestLocationInformation-r13 |
Not present |
||
tbs-RequestLocationInformation-r13 |
Not present |
||
wlan-RequestLocationInformation-r13 |
Not present |
||
bt-RequestLocationInformation-r13 |
Not present |
||
nr-ECID-RequestLocationInformation-r16 |
Not present |
||
nr-Multi-RTT-RequestLocationInformation-r16 SEQUENCE { |
|||
nr-UE-RxTxTimeDiffMeasurementInfoRequest-r16 |
Not present |
||
nr-RequestedMeasurements-r16 |
bit 0 = 1 (prsrsrpReq) |
||
nr-AssistanceAvailability-r16 |
FALSE |
||
nr-Multi-RTT-ReportConfig-r16 SEQUENCE { |
|||
maxDL-PRS-RxTxTimeDiffMeasPerTRP-r16 |
Not present |
||
timingReportingGranularityFactor-r16 |
Not present |
||
} |
|||
additionalPaths-r16 |
Not present |
||
} |
|||
nr-DL-AoD-RequestLocationInformation-r16 |
Not present |
||
nr-DL-TDOA-RequestLocationInformation-r16 |
Not present |
||
} |
|||
} |
|||
} |
|||
} |
|||
} |
|||
} |
Table 15.2.2.4.3-6: LPP ProvideAssistanceData
Derivation Path: 37.355 clause 6.2 |
|||
Information Element |
Value/remark |
Comment |
Condition |
LPP-Message ::= SEQUENCE { |
|||
transactionID SEQUENCE { |
|||
initiator |
locationServer |
||
transactionNumber |
(0..255) |
||
} |
|||
endTransaction |
TRUE |
||
sequenceNumber |
Not present |
||
acknowledgement |
Not present |
||
lpp-MessageBody CHOICE { |
|||
c1 CHOICE { |
|||
provideAssistanceData SEQUENCE { |
|||
criticalExtensions CHOICE { |
|||
c1 CHOICE { |
|||
provideAssistanceData-r9 SEQUENCE { |
|||
commonIEsProvideAssistanceData |
Not present |
||
a-gnss-ProvideAssistanceData |
Not present |
||
otdoa-ProvideAssistanceData |
Not present |
||
epdu-Provide-AssistanceData |
Not present |
||
sensor-ProvideAssistanceData-r15 |
Not present |
||
tbs-ProvideAssistanceData-r15 |
Not present |
||
wlan-ProvideAssistanceData-r15 |
Not present |
||
nr-Multi-RTT-ProvideAssistanceData-r16 SEQUENCE { |
|||
nr-DL-PRS-AssistanceData |
As defined in Table 15.2.2.4.3-7 |
||
nr-SelectedDL-PRS-IndexList-r16 |
Not present |
||
nr-Multi-RTT-Error-r16 |
Not present |
||
} |
|||
nr-DL-AoD-ProvideAssistanceData-r16 |
Not present |
||
nr-DL-TDOA-ProvideAssistanceData-r16 |
Not present |
||
} |
|||
} |
|||
} |
|||
} |
|||
} |
|||
} |
Table 15.2.2.4.3-7: NR-DL-PRS-AssistanceData
Derivation Path: 37.355 clause 6.4.3 |
|||
Information Element |
Value/remark |
Comment |
Condition |
NR-DL-PRS-AssistanceData-r16 ::= SEQUENCE { |
|||
nr-DL-PRS-ReferenceInfo-r16 SEQUENCE { |
|||
dl-PRS-ID-r16 |
0 |
||
nr-DL-PRS-ResourceID-List-r16 |
Not present |
||
nr-DL-PRS-ResourceSetID-r16 |
Not present |
||
} |
|||
nr-DL-PRS-AssistanceDataList-r16 SEQUENCE (SIZE (1..nrMaxFreqLayers-r16)) OF NR-DL-PRS-AssistanceDataPerFreq-r16 { |
2 entries |
||
NR-DL-PRS-AssistanceDataPerFreq-r16[1] SEQUENCE { |
entry 1 |
||
nr-DL-PRS-PositioningFrequencyLayer-r16 SEQUENCE { |
|||
dl-PRS-SubcarrierSpacing-r16 |
kHz15 |
Configuration 1 and Configuration 2 |
|
kHz30 |
Configuration 3 |
||
dl-PRS-ResourceBandwidth-r16 |
21 |
104 PRBs |
Configuration 1 and Configuration 2 |
28 |
132 PRBs |
Configuration 3 |
|
dl-PRS-StartPRB-r16 |
0 |
||
dl-PRS-PointA-r16 |
absoluteFrequencyPointA as defined for the DL frequency of the Cell 1 |
||
dl-PRS-CombSizeN-r16 |
n4 |
||
dl-PRS-CyclicPrefix-r16 |
normal |
||
} |
|||
nr-DL-PRS-AssistanceDataPerFreq-r16 SEQUENCE (SIZE (1..nrMaxTRPsPerFreq-r16)) OF NR-DL-PRS-AssistanceDataPerTRP-r16{ |
1 entry |
||
NR-DL-PRS-AssistanceDataPerTRP-r16[1] SEQUENCE { |
entry 1 |
Cell 1 |
|
dl-PRS-ID-r16 |
0 |
||
nr-PhysCellID-r16 |
Cell 1 |
||
nr-CellGlobalID-r16 |
Cell 1 |
||
nr-ARFCN-r16 |
Cell 1 |
||
nr-DL-PRS-SFN0-Offset-r16 SEQUENCE { |
|||
sfn-Offset-r16 |
0 |
||
integerSubframeOffset-r16 |
0 |
||
} |
|||
nr-DL-PRS-ExpectedRSTD-r16 |
0 |
||
nr-DL-PRS-ExpectedRSTD-Uncertainty-r16 |
0 |
||
nr-DL-PRS-Info-r16 |
As specified in Table 15.2.2.4.3-8 |
||
} |
|||
} |
|||
} |
|||
NR-DL-PRS-AssistanceDataPerFreq-r16[2] SEQUENCE { |
entry 2 |
||
nr-DL-PRS-PositioningFrequencyLayer-r16 SEQUENCE { |
|||
dl-PRS-SubcarrierSpacing-r16 |
kHz15 |
Configuration 1 and Configuration 2 |
|
kHz30 |
Configuration 3 |
||
dl-PRS-ResourceBandwidth-r16 |
21 |
104 PRBs |
Configuration 1 and Configuration 2 |
28 |
132 PRBs |
Configuration 3 |
|
dl-PRS-StartPRB-r16 |
0 |
||
dl-PRS-PointA-r16 |
absoluteFrequencyPointA as defined for the DL frequency of the Cell 2 |
||
dl-PRS-CombSizeN-r16 |
n4 |
||
dl-PRS-CyclicPrefix-r16 |
normal |
||
} |
|||
nr-DL-PRS-AssistanceDataPerFreq-r16 SEQUENCE (SIZE (1..nrMaxTRPsPerFreq-r16)) OF NR-DL-PRS-AssistanceDataPerTRP-r16{ |
1 entry |
||
NR-DL-PRS-AssistanceDataPerTRP-r16[1] SEQUENCE { |
entry 1 |
Cell 2 |
|
dl-PRS-ID-r16 |
1 |
||
nr-PhysCellID-r16 |
Cell 2 |
||
nr-CellGlobalID-r16 |
Cell 2 |
||
nr-ARFCN-r16 |
Cell 2 |
||
nr-DL-PRS-SFN0-Offset-r16 SEQUENCE { |
|||
sfn-Offset-r16 |
0 |
||
integerSubframeOffset-r16 |
0 |
||
} |
|||
nr-DL-PRS-ExpectedRSTD-r16 |
23 |
About 3 s |
|
nr-DL-PRS-ExpectedRSTD-Uncertainty-r16 |
39 |
About 5 s |
|
nr-DL-PRS-Info-r16 |
As specified in Table 15.2.2.4.3-8 |
||
} |
|||
} |
|||
} |
|||
} |
|||
} |
Table 15.2.2.4.3-8: NR-DL-PRS-Info
Derivation Path: 37.355 clause 6.4.3 |
|||
Information Element |
Value/remark |
Comment |
Condition |
NR-DL-PRS-Info-r16 ::= SEQUENCE { |
|||
nr-DL-PRS-ResourceSetList-r16 SEQUENCE (SIZE (1..nrMaxSetsPerTrp-r16)) OF NR-DL-PRS-ResourceSet-r16 { |
1 entry |
||
NR-DL-PRS-ResourceSet-r16[1] SEQUENCE { |
entry 1 |
||
nr-DL-PRS-ResourceSetID-r16 |
0 |
||
dl-PRS-Periodicity-and-ResourceSetSlotOffset-r16 CHOICE { |
|||
scs15-r16 CHOICE { |
Configuration 1 and Configuration 2 |
||
n160-r16 |
10 |
||
} |
|||
scs30-r16 CHOICE { |
Configuration 3 |
||
n160-r16 |
20 |
||
} |
|||
dl-PRS-ResourceRepetitionFactor-r16 |
Not present |
||
dl-PRS-ResourceTimeGap-r16 |
s1 |
||
dl-PRS-NumSymbols-r16 |
n4 |
||
dl-PRS-MutingOption1-r16 SEQUENCE { |
|||
dl-prs-MutingBitRepetitionFactor-r16 |
Not present |
||
nr-option1-muting-r16 CHOICE { |
|||
po2-r16 |
10 |
Cell 1 |
|
01 |
Cell 2 |
||
} |
|||
} |
|||
dl-PRS-MutingOption2-r16 |
Not present |
||
dl-PRS-ResourcePower-r16 |
27 |
||
dl-PRS-ResourceList-r16 SEQUENCE (SIZE (1..nrMaxResourcesPerSet-r16)) OF NR-DL-PRS-Resource-r16 { |
1 entry |
||
NR-DL-PRS-Resource-r16[1] SEQUENCE { |
entry 1 |
||
nr-DL-PRS-ResourceID-r16 |
0 |
||
dl-PRS-SequenceID-r16 |
0 |
||
dl-PRS-CombSizeN-AndReOffset-r16 CHOICE { |
|||
n4-r16 |
0 |
||
} |
|||
dl-PRS-ResourceSlotOffset-r16 |
4 |
||
dl-PRS-ResourceSymbolOffset-r16 |
0 |
||
dl-PRS-QCL-Info-r16 |
Not present |
||
} |
|||
} |
|||
} |
|||
} |
|||
} |
Table 15.2.2.4.3-9: LPP ProvideLocation Information
Derivation Path: 37.355 clause 6.5.12 |
||||
Information Element |
Value/remark |
Comment |
Condition |
|
LPP-Message ::= SEQUENCE { |
||||
transactionID SEQUENCE { |
||||
initiator |
locationServer |
|||
transactionNumber |
1 |
|||
} |
||||
endTransaction |
TRUE |
|||
sequenceNumber |
(0..255) |
|||
acknowledgement |
||||
lpp-MessageBody CHOICE { |
||||
c1 CHOICE { |
||||
provideLocationInformation SEQUENCE { |
||||
criticalExtensions CHOICE { |
||||
c1 CHOICE { |
||||
provideLocationInformation-r9 SEQUENCE { |
||||
commonIEsProvideLocationInformation |
Not present. |
|||
a-gnss-ProvideLocationInformation |
Not present |
|||
otdoa-ProvideLocationInformation |
Not present |
|||
ecid-ProvideLocationInformation |
Not present |
|||
epdu-ProvideLocationInformation |
Not present |
|||
sensor-ProvideLocationInformation-r13 |
Not present |
|||
tbs-ProvideLocationInformation-r13 |
Not present |
|||
wlan-ProvideLocationInformation-r13 |
Not present |
|||
bt-ProvideLocationInformation-r13 |
Not present |
|||
nr-ECID-ProvideLocationInformation-r16 |
Not present |
|||
nr-Multi-RTT-ProvideLocationInformation-r16 SEQUENCE { |
||||
nr-Multi-RTT-SignalMeasurementInformation-r16 SEQUENCE { |
||||
nr-Multi-RTT-MeasList-r16 SEQUENCE (SIZE(1..nrMaxTRPs-r16)) OF NR-Multi-RTT-MeasElement-r16 { |
2 entries |
|||
NR-Multi-RTT-MeasElement-r16[1] SEQUENCE { |
entry 1 |
|||
dl-PRS-ID-r16 |
INTEGER (0..255) |
|||
nr-PhysCellID-r16 |
||||
nr-CellGlobalID-r16 |
||||
nr-ARFCN-r16 |
||||
nr-DL-PRS-ResourceID-r16 |
||||
nr-DL-PRS-ResourceSetID-r16 |
||||
nr-UE-RxTxTimeDiff-r16 |
Present. Any value acceptable. |
|||
nr-AdditionalPathList-r16 |
||||
nr-TimeStamp-r16 |
||||
nr-TimingQuality-r16 |
||||
nr-DL-PRS-RSRP-Result-r16 |
||||
nr-Multi-RTT-AdditionalMeasurements-r16 |
||||
} |
||||
NR-Multi-RTT-MeasElement-r16[2] SEQUENCE { |
entry 2 |
|||
dl-PRS-ID-r16 |
INTEGER (0..255) |
|||
nr-PhysCellID-r16 |
||||
nr-CellGlobalID-r16 |
||||
nr-ARFCN-r16 |
||||
nr-DL-PRS-ResourceID-r16 |
||||
nr-DL-PRS-ResourceSetID-r16 |
||||
nr-UE-RxTxTimeDiff-r16 |
Present. Any value acceptable. |
|||
nr-AdditionalPathList-r16 |
||||
nr-TimeStamp-r16 |
||||
nr-TimingQuality-r16 |
||||
nr-DL-PRS-RSRP-Result-r16 |
||||
nr-Multi-RTT-AdditionalMeasurements-r16 |
||||
} |
||||
} |
||||
nr-NTA-Offset-r16 |
||||
} |
||||
nr-Multi-RTT-Error-r16 |
||||
} |
||||
nr-DL-AoD-ProvideLocationInformation-r16 |
Not present |
|||
} |
||||
} |
||||
} |
||||
} |
||||
} |
||||
} |
||||
} |
15.2.2.5 Test requirement
Table 15.2.2.5-1 and Table 15.2.2.5-2 define the primary level settings not including the test tolerances for the test.
Table 15.2.2.5-1: General test parameters
Parameter |
Unit |
Test configuration |
Value |
Comment |
Active cell |
1, 2, 3 |
Cell 1 |
Cell 1 is the PCell in NR-Multi-RTT-ProvideAssistanceData [49]. |
|
Neighbour cell |
1, 2, 3 |
Cell 2 |
Cell 2 is a neighbour cell in NR-Multi-RTT-ProvideAssistanceData [49]. |
|
RF Channel Number |
1, 2, 3 |
1 |
For Cell 1 |
|
RF Channel Number |
1, 2, 3 |
2 |
For Cell 2 |
|
BWchannel |
MHz |
1 |
10: NRB,c = 52 |
|
2 |
10: NRB,c = 52 |
|||
3 |
40: NRB,c = 106 |
|||
SSB configuration |
1 |
SSB.1 FR1 |
||
2 |
SSB.1 FR1 |
|||
3 |
SSB.2 FR1 |
|||
SMTC configuration |
1 |
SMTC.2 |
||
2 |
SMTC.1 |
|||
3 |
SMTC.1 |
|||
Measurement gap |
1, 2, 3 |
GP#24 or GP#0 Note 1 |
||
CP length |
1, 2, 3 |
Normal |
||
DRX |
1, 2, 3 |
OFF |
||
Time offset between serving and neighbour cells |
μs |
1, 2, 3 |
3 |
Synchronous cells |
T1 |
s |
1, 2, 3 |
5 |
|
T2 |
s |
1, 2, 3 |
10 |
|
Note 1: GP#24 is configured if UE supports MG#24, otherwise GP#0 is configured. |
Table 15.2.2.5-2: Cell specific test parameters
Parameter |
Unit |
Test configuration |
Cell 1 |
Cell 2 |
||
T1 |
T2 |
T1 |
T2 |
|||
TDD configuration |
1 |
N/A |
N/A |
|||
2 |
TDDConf.1.1 |
TDDConf.1.1 |
||||
3 |
TDDConf.2.1 |
TDDConf.2.1 |
||||
PDSCH RMC configuration |
1 |
SR.1.1 FDD |
N/A |
|||
2 |
SR.1.1 TDD |
|||||
3 |
SR.2.1 TDD |
|||||
RMSI CORESET RMC configuration |
1 |
CR.1.1 FDD |
N/A |
|||
2 |
CR.1.1 TDD |
|||||
3 |
CR.2.1 TDD |
|||||
Dedicated CORESET RMC configuration |
1 |
CCR.1.1 FDD |
N/A |
|||
2 |
CCR.1.1 TDD |
|||||
3 |
CCR.2.1 TDD |
|||||
OCNG Patterns |
1, 2, 3 |
OP.1 |
OP.1 |
|||
TRS Configuration |
1 |
TRS.1.1 FDD |
N/A |
|||
2 |
TRS.1.1 TDD |
|||||
3 |
TRS.1.2 TDD |
|||||
Initial BWP configuration |
1, 2, 3 |
DLBWP.0.1 ULBWP.0.1 |
N/A |
|||
Active DL BWP configuration |
1, 2, 3 |
DLBWP.1.1 |
N/A |
|||
Active UL BWP configuration |
1, 2, 3 |
ULBWP.1.1 |
N/A |
|||
PRS configuration |
1 |
PRS.1.2 FR1 |
PRS.1.2 FR1 |
|||
2 |
PRS.1.2 FR1 |
PRS.1.2 FR1 |
||||
3 |
PRS.2.2 FR1 |
PRS.2.2 FR1 |
||||
PRS muting info |
1, 2, 3 |
‘10’ |
‘01’ |
|||
SRS configuration |
1 |
POS-SRS.1 |
N/A |
|||
2 |
POS-SRS.1 |
N/A |
||||
3 |
POS-SRS.2 |
N/A |
||||
Note 2 |
dBm/SCS |
1 |
-98 |
|||
2 |
-98 |
|||||
3 |
-95 |
|||||
Note 2 |
dBm/15 kHz |
1 |
-98 |
|||
2 |
||||||
3 |
||||||
PRS |
dB |
1 |
-Infinity |
-3 |
-Infinity |
-13 |
2 |
||||||
3 |
||||||
PRS |
dB |
1 |
-Infinity |
-2.4 |
-Infinity |
-12.4 |
2 |
||||||
3 |
||||||
PRS-RSRP Note 3 |
dBm/SCS kHz |
1 |
-Infinity |
-100.4 |
-Infinity |
-110.4 |
2 |
-Infinity |
-100.4 |
-Infinity |
-110.4 |
||
3 |
-Infinity |
-97.4 |
-Infinity |
-107.4 |
||
Io |
dBm/9.36 MHz |
1 |
N/A |
-68.07 |
N/A |
-69.81 |
dBm/9.36 MHz |
2 |
-68.07 |
-69.81 |
|||
dBm/38.16 MHz |
3 |
-61.98 |
-63.562 |
|||
Propagation Condition |
1, 2, 3 |
AWGN |
||||
Note 1: The resources for uplink transmission are assigned to the UE prior to the start of time period T2. Note 2: Interference from other cells and noise sources not specified in the test is assumed to be constant over subcarriers and time and shall be modelled as AWGN of appropriate power for to be fulfilled. Note 3: PRS-RSRP levels have been derived from other parameters for information purposes. They are not settable parameters themselves. |
The UE Rx-Tx time difference measurement period fulfils the requirements specified in clause 15.2.2.2.
The response time is equal to the LPP time IE value plus the test tolerance. The LPP time IE value is derived from the Rx-Tx measurement period plus ΔT, where ΔT = 50 ms, giving a value of 19570 ms assuming durationOfPRS-ProcessingSymbols-r16 is 0.125 ms and durationOfPRS-ProcessingSymbolsInEveryTms is 1280 ms. Including the test tolerance of 300 ms results in 19870ms. This is rounded up to the next allowed LPP value of 20 seconds. The RSTD measurement reporting delay in the test is derived from the following expression, the parameters specified in clause 15.2.1.3.
The rate of successful tests during repeated tests shall be at least 90% with a confidence level of 95%.