10.2A TDD RSTD Measurement Reporting Delay for Carrier Aggregation for 20 MHz Bandwidth
37.571-13GPPPart 1: Conformance test specificationRelease 16TSUser Equipment (UE) conformance specification for UE positioning
10.2A.1 Test purpose
Same as defined in clause 10.2.1.
NOTE: This test verifies the requirement which is independent of channel bandwidth and is performed according to the principle defined in clause 4.7.5.
10.2A.2 Test applicability
This test applies to all types of E-UTRA TDD UE release 10 and forward that supports UE-assisted OTDOA for Carrier Aggregation.
10.2A.3 Minimum conformance requirements
Same as defined in clause 10.2.3.
The normative reference for this requirement is TS 36.133 [23] clause 8.4.3, 8.4.4 and A.8.17.4.
10.2A.4 Test description
10.2A.4.1 Initial conditions
Same as defined in clause 10.2.4.1 except that the values of the parameters in Table 10.2A.4.1-1 will replace the values of the corresponding parameters in Table 10.2.4.1-1.
Channel bandwidth to be tested: 20 MHz.
Table 10.2A.4.1-1: General test parameters for E-UTRAN TDD RSTD measurement reporting delay under fading propagation conditions for carrier aggregation for 20 MHz
Parameter |
Unit |
Value |
Comment |
|
Test 1 |
Test 2 |
|||
PCFICH/PDCCH/PHICH parameters |
DL Reference Measurement Channel R.10 TDD |
As specified in TS 36.521-3 [25] clause A.2.2 |
||
Channel Bandwidth (BWchannel) |
MHz |
20 |
||
PRS Transmission Bandwidth |
RB |
100 |
PRS are transmitted over the system bandwidth |
|
Note 1: See Table 10.2.4.1-1 for the other parameters. Note 2: This test verifies the requirement which is independent of channel bandwidth and is performed according to the principle defined in clause 4.7.5. |
10.2A.4.2 Test procedure
Same as defined in clause 10.2.4.2.
10.2A.4.3 Message contents
Same as defined in clause 10.2.4.3.
10.2A.5 Test requirement
Same as defined in clause 10.2.5 except that the values of the parameters in Table 10.2A.5-1 and Table 10.2A.5-2 will replace the values of the corresponding parameters in Table 10.2.5-1 and Table 10.2.5-2, respectively.
Table 10.2A.5-1: Cell-specific test parameters for E-UTRAN TDD RSTD measurement reporting delay under fading propagation conditions during T1 for carrier aggregation for 20 MHz
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
OCNG patterns defined in TS 36.521-3 [25] clause D.2 |
OP.7 TDD |
N/A |
N/A |
|
Io Note 1 |
dBm/ 18 MHz |
-64.21 |
N/A |
N/A |
Note 1: Io levels have been derived from other parameters for information purposes. They are not settable parameters themselves. Note 2: See Table 10.2.5-1 for the other parameters. |
Table 10.2A.5-2: Cell-specific test parameters for E-UTRAN TDD RSTD measurement reporting delay under fading propagation conditions during T2 and T3 for carrier aggregation for 20 MHz
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
|||
T2 |
T3 |
T2 |
T3 |
T2 |
T3 |
||
OCNG patterns defined in TS 36.521-3 [25] clause D.2 |
OP.7 TDD |
OP.8 TDD |
OP.8 TDD |
N/A |
|||
Io Note 1 |
dBm/ 18 MHz |
-66.93 |
N/A |
N/A |
-63.67 |
-67.09 |
N/A |
Note 1: Io levels have been derived from other parameters for information purposes. They are not settable parameters themselves. Note 2: See Table 10.2.5-2 for the other parameters. |