10.4B TDD RSTD Measurement Accuracy for Carrier Aggregation for 5 MHz + 5 MHz bandwidth
37.571-13GPPPart 1: Conformance test specificationRelease 16TSUser Equipment (UE) conformance specification for UE positioning
10.4B.1 Test purpose
Same as defined in clause 10.4.1.
10.4B.2 Test applicability
This test applies to all types of E-UTRA TDD UE release 10 and forward that supports UE-assisted OTDOA for Carrier Aggregation.
10.4B.3 Minimum conformance requirements
Same as defined in clause 10.4.3.
The normative reference for this requirement is TS 36.133 [23] clause 9.1.12 and A.9.8.12.
10.4B.4 Test description
10.4B.4.1 Initial conditions
Same as defined in clause 10.4.4.1 except that the values of the parameters in Table 10.4B.4.1-1 will replace the values of the corresponding parameters in Table 10.4.4.1-1.
Channel bandwidth to be tested: 5 MHz.
Table 10.4B.4.1-1: General Test Parameters for RSTD Test for E-UTRAN TDD for Carrier Aggregation for 5 MHz + 5 MHz
Parameter |
Unit |
Value |
Comment |
PCFICH/PDCCH/PHICH parameters |
R.11 TDD |
As specified in clause TS 36.521-3 [25] clause A.2.2 |
|
OCNG Patterns defined in TS 36.521-3 [25] clause D.2 |
OP.10 TDD |
OCNG shall be used such that both cells are fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols (other than those in the PRS subframes). There is no PDSCH allocated in the subframe transmitting PRS. |
|
Channel Bandwidth (BWchannel) |
MHz |
5 |
|
PRS Bandwidth |
RB |
25 |
PRS Bandwidth bandwidth is as indicated in prs-Bandwidth in the OTDOA assistance data defined in 3GPP TS 36.355 [4]. |
Number of consecutive positioning downlink subframes |
2 |
As defined in 3GPP TS 36.211 [26] |
|
Note 1: See Table 10.4.4.1-1 for other general test parameters. |
10.4B.4.2 Test procedure
Same as defined in clause 10.4.4.2.
10.4B.4.3 Message contents
Same as defined in clause 10.4.4.3.
10.4B.5 Test requirement
Same as defined in clause 10.4.5 except that the value of the parameter in Table 10.4B.5-1 will replace the value of the corresponding parameter in Table 10.4.5-1 and the TDD RSTD accuracy shall meet the reported values in Table 10.4B.5-2.
Table 10.4B.5-1: Cell Specific Test Parameters for RSTD Test for E-UTRAN TDD for Carrier Aggregation for 5 MHz + 5 MHz bandwidth
Parameter |
Unit |
Cell1 |
Cell2 |
Cell3 |
Io Note1 |
dBm/4.5 MHz |
-73.05 |
-73.00 |
-73.00 |
Note 1: Io level has been derived from other parameters for information purposes. It is not settable parameter itself. Io values are derived in the case that there is no PBCH, PSS or SSS in the OFDM symbols carrying PRS Note 2: See Table 10.4.5-1 for other cell specific test parameters. |
Table 10.4B.5-2: RSTD TDD accuracy requirements for the reported values for Carrier Aggregation for 5 MHz+5 MHz bandwidth
Value |
|
Lowest reported value |
RSTD_6379 |
Highest reported value |
RSTD_6393 |