10.1C FDD RSTD Measurement Reporting Delay for Carrier Aggregation for 10 MHz+5 MHz Bandwidth

37.571-13GPPPart 1: Conformance test specificationRelease 16TSUser Equipment (UE) conformance specification for UE positioning

10.1C.1 Test purpose

Same as defined in clause 10.1.1.

NOTE: This test verifies the requirement which is independent of channel bandwidth and is performed according to the principle defined in clause 4.7.5.

10.1C.2 Test applicability

This test applies to all types of E-UTRA FDD UE release 12 and forward that supports UE-assisted OTDOA for Carrier Aggregation.

10.1C.3 Minimum conformance requirements

Same as defined in clause 10.1.3.

The normative reference for this requirement is TS 36.133 [23] clause 8.4.3, 8.4.4 and A.8.17.5.

10.1C.4 Test description

10.1C.4.1 Initial conditions

Same as defined in clause 10.1.4.1 except that the values of the parameters in Table 10.1C.4.1-1 will replace the values of the corresponding parameters in Table 10.1.4.1-1.

Channel bandwidth to be tested: Cell 1: 10 MHz, Cell 2 and Cell 3: 5 MHz.

Table 10.1C.4.1-1: General test parameters for E-UTRAN FDD RSTD measurement reporting delay under fading propagation conditions for carrier aggregation for 10 MHz + 5 MHz

Parameter

Unit

Value

Comment

Test 1

Test 2

PCFICH/PDCCH/PHICH parameters

Cell 1: R.6 FDD

Cell 2: R.11 FDD

Cell 3: R.11 FDD

Cell 1: R.6 FDD

Cell 2: R.11 FDD

Cell 3: R.11 FDD

As specified in TS 36.521-3 [25] clause A.2.1

Channel Bandwidth (BWchannel)

MHz

Cell 1: 10

Cell 2: 5

Cell 3: 5

Cell 1: 10

Cell 2: 5

Cell 3: 5

PRS Transmission Bandwidth

RB

Cell 1: 50

Cell 2: 25

Cell 3: 25

Cell 1: 50

Cell 2: 25

Cell 3: 25

PRS are transmitted over the system bandwidth

PRS occasion length

Cell 1: 1

Cell 2: 2

Cell 3: 2

Cell 1: 1

Cell 2: 2

Cell 3: 2

Note 1: See Table 10.1.4.1-1 for the other parameters.

Note 2: This test verifies the requirement which is independent of channel bandwidth and is performed according to the principle defined in section 4.7.5.

10.1C.4.2 Test procedure

Same as defined in clause 10.1.4.2.

10.1C.4.3 Message contents

Same as defined in clause 10.1.4.3.

10.1C.5 Test requirement

Same as defined in clause 10.1.5 except that the values of the parameters in Table 10.1C.5-1 and Table 10.1C.5-2 will replace the values of the corresponding parameters in Table 10.1.5-1 and Table 10.1.5-2, respectively.

Table 10.1C.5-1: Cell-specific test parameters for E-UTRAN FDD RSTD measurement reporting delay under fading propagation conditions during T1 for carrier aggregation for 10 MHz + 5 MHz

Parameter

Unit

Cell 1

Cell 2

Cell 3

Io Note 1

dBm/

9 MHz

-67.22

N/A

N/A

dBm/

4.5 MHz

N/A

N/A

N/A

Note 1: Io levels have been derived from other parameters for information purposes. They are not settable parameters themselves.

Note 2: See Table 10.1.5-1 for the other parameters.

Table 10.1C.5-2: Cell-specific test parameters for E-UTRAN FDD RSTD measurement reporting delay under fading propagation conditions during T2 and T3 for carrier aggregation for 10 MHz + 5 MHz

Parameter

Unit

Cell 1

Cell 2

Cell 3

T2

T3

T2

T3

T2

T3

OCNG patterns defined in TS 36.521-3 [25] clause D.1

OP.5 FDD

OP.19 FDD

OP.19 FDD

N/A

Io Note 1

dBm/

9 MHz

-69.94

N/A

N/A

N/A

N/A

N/A

dBm/

4.5 MHz

N/A

N/A

N/A

-69.69

-73.12

N/A

Note 1: Io levels have been derived from other parameters for information purposes. They are not settable parameters themselves.

Note 2: See Table 10.1.5-2 for the other parameters.