C.2 Environmental requirements for the UE
25.1023GPPRelease 17TSUser Equipment (UE) radio transmission and reception (TDD)
The requirements in this clause apply to all types of UE(s)
C.2.1 Temperature
The UE shall fulfil all the requirements in the full temperature range of:
Table C.1
|
+15C – +35 C |
for normal conditions (with relative humidity of 25 % to 75 %); |
|
-10C ‑ +55C |
for extreme conditions (see IEC publications 68‑2‑1 and 68‑2‑2) |
Outside this temperature range the UE, if powered on, shall not make ineffective use of the radio frequency spectrum. In no case shall the UE exceed the transmitted levels as defined in S25.102 for extreme operation.
C.2.2 Voltage
The UE shall fulfil all the requirements in the full voltage range, i.e. the voltage range between the extreme voltages.
The manufacturer shall declare the lower and higher extreme voltages and the approximate shutdown voltage. For the equipment that can be operated from one or more of the power sources listed below, the lower extreme voltage shall not be higher, and the higher extreme voltage shall not be lower than that specified below.
Table C.2
|
Power source |
Lower extreme voltage |
Higher extreme voltage |
Normal conditions voltage |
|
AC mains |
0,9 * nominal |
1,1 * nominal |
nominal |
|
Regulated lead acid battery |
0,9 * nominal |
1,3 * nominal |
1,1 * nominal |
|
Non regulated batteries: Leclanché/lithium Mercury/nickel cadmium |
0,85 * nominal 0,90 * nominal |
Nominal Nominal |
Nominal Nominal |
Outside this voltage range the UE if powered on, shall not make ineffective use of the radio frequency spectrum. In no case shall the UE exceed the transmitted levels as defined in S4.01A for extreme operation. In particular, the UE shall inhibit all RF transmissions when the power supply voltage is below the manufacturer declared shutdown voltage.
C.2.3 Vibration
The UE shall fulfil all the requirements when vibrated at the following frequency/amplitudes:
Table C.3
|
Frequency |
ASD (Acceleration Spectral Density) random vibration |
|
5 Hz to 20 Hz |
0,96 m2/s3 |
|
20 Hz to 500 Hz |
0,96 m2/s3 at 20 Hz, thereafter ‑3 dB/Octave |
Outside the specified frequency range the UE, if powered on, shall not make ineffective use of the radio frequency spectrum. In no case shall the UE exceed the transmitted levels as defined in S4.01A for extreme operation.
Annex D (informative):
Terminal capabilities (TDD)
Void
[Note: All UE capabilities can be found in 3GPP TS 25.306]
Annex E (informative):
Change history
|
TSG |
29 |
CR |
R |
Title |
Cat |
Curr |
New |
Work Item |
|
RP-29 |
Rel-7 version created based on v6.2.0 |
7.0.0 |
||||||
|
RP-29 |
RP-050501 |
0153 |
Introduction of UMTS 2.6GHz operating band for TDD |
B |
6.1.0 |
7.0.0 |
RinImp-UMTS2600TDD |
|
|
RP-29 |
RP-050501 |
0154 |
UMTS 2.6 GHz TDD Propagation Conditions |
B |
6.1.0 |
7.0.0 |
RinImp-UMTS2600TDD |
|
|
RP-29 |
RP-050501 |
0155 |
UMTS 2.6 GHz TDD UE Receiver Specifications |
B |
6.1.0 |
7.0.0 |
RinImp-UMTS2600TDD |
|
|
RP-29 |
RP-050501 |
0156 |
2 |
Channel Raster and UARFCN for 3.84 Mcps TDD in UMTS 2.6 GHz |
B |
6.1.0 |
7.0.0 |
RinImp-UMTS2600TDD |
|
RP-29 |
RP-050501 |
0157 |
Introduction of UMTS 2.6 GHz new operating band for 1.28Mcps TDD |
B |
6.1.0 |
7.0.0 |
RinImp-UMTS2600TDD |
|
|
RP-29 |
RP-050501 |
0158 |
Introduction of Propagation Conditions for UMTS 2.6 GHz for 1.28Mcps TDD |
B |
6.1.0 |
7.0.0 |
RinImp-UMTS2600TDD |
|
|
RP-29 |
RP-050501 |
0159 |
Introduction of UMTS 2.6 GHz requirements for blocking and spurious emission of UE receiver for 1.28Mcps TDD |
B |
6.1.0 |
7.0.0 |
RinImp-UMTS2600TDD |
|
|
RP-30 |
RP-050740 |
0160 |
1 |
Additional UE Tx Spurious Emission for co-existence with 2.6 GHz FDD |
B |
7.0.0 |
7.1.0 |
RinImp-UMTS2600TDD |
|
RP-31 |
RP-060104 |
0162 |
1 |
Modifications to HSDPA test parameters for 1.28Mcps TDD |
A |
7.1.0 |
7.2.0 |
TEI6 |
|
RP-31 |
RP-060113 |
0163 |
1 |
MBMS Requirements for MCCH & MTCH channels |
B |
7.1.0 |
7.2.0 |
MBMS-RAN-RF-TDD |
|
RP-32 |
RP-060313 |
0165 |
2 |
1.28Mcps TDD MBMS UE performance requirements |
B |
7.2.0 |
7.3.0 |
MBMS-RAN-RF-TDD |
|
RP-32 |
RP-060309 |
0166 |
1 |
7.68 Mcps Frequency Band & Channel Arrangement |
B |
7.2.0 |
7.3.0 |
VHCRTDD-RF |
|
RP-32 |
RP-060309 |
0167 |
2 |
7.68 Mcps UE Transmitter Characteristics |
B |
7.2.0 |
7.3.0 |
VHCRTDD-RF |
|
RP-32 |
RP-060309 |
0168 |
7.68 Mcps UE Receiver Characteristics |
B |
7.2.0 |
7.3.0 |
VHCRTDD-RF |
|
|
RP-32 |
RP-060309 |
0169 |
7.68 Mcps – Channel Performance |
B |
7.2.0 |
7.3.0 |
VHCRTDD-RF |
|
|
RP-32 |
RP-060309 |
0170 |
1 |
7.68 Mcps Measurement Channels & Propagation Conditions |
B |
7.2.0 |
7.3.0 |
VHCRTDD-RF |
|
RP-33 |
RP-060522 |
0180 |
HS-SCCH performance requirement for 3.84 Mcps TDD option and 7.68 Mcps TDD option |
7.3.0 |
7.4.0 |
TEI7 |
||
|
RP-33 |
RP-060516 |
0185 |
1 |
Out of band blocking for 3.84 Mcps and 7.68 Mcps TDD UE operating in 2010-2025 MHz of band (a) in Japan. |
7.3.0 |
7.4.0 |
TEI7 |
|
|
RP-33 |
RP-060517 |
0190 |
Clarification of Tx spurious emission level from 3.84 Mcps and 7.68 MCps TDD UE into PHS band |
7.3.0 |
7.4.0 |
TEI7 |
||
|
RP-33 |
RP-060529 |
0192 |
Editorial corrections to 3.84 Mcps TDD UE performances on MBMS. |
7.3.0 |
7.4.0 |
TEI7 |
||
|
RP-33 |
RP-060528 |
0193 |
Performance requirements for 3.84 Mcps E-DCH associated downlink signalling channels: E-AGCH and E-HICH |
7.3.0 |
7.4.0 |
TEI7 |
||
|
RP-33 |
RP-060526 |
0194 |
7.68 Mcps Operations in 2.6 GHz band |
7.3.0 |
7.4.0 |
TEI7 |
||
|
RP-33 |
RP-060530 |
0195 |
Clarification of 7.68 Mcps TDD UE ACLR at +/- 10 MHz offset. |
7.3.0 |
7.4.0 |
MBMS-RAN-RF-TDD |
||
|
RP-33 |
RP-060530 |
0196 |
Performance requirements for 3.84 Mcps E-DCH associated downlink signalling channels: E-AGCH and E-HICH |
7.3.0 |
7.4.0 |
EDCHTDD-RF |
||
|
RP-34 |
RP-060810 |
0200 |
Combined MBMS demodulation and Cell identification requirement for 1.28 Mcps TDD |
A |
7.4.0 |
7.5.0 |
TEI6 |
|
|
RP-34 |
RP-060818 |
0198 |
Performance requirements for 7.68 Mcps E-DCH associated downlink signalling channels: E-AGCH and E-HICH |
B |
7.4.0 |
7.5.0 |
TEI7 |
|
|
RP-34 |
RP-060816 |
0197 |
PLCCH Performance Requirement |
B |
7.4.0 |
7.5.0 |
RANimp-RABSE-CodOptLCRTDD |
|
|
RP-35 |
RP-070081 |
0209 |
Modificaiton to SEM for 1.28Mcps TDD |
A |
7.5.0 |
7.6.0 |
TEI4 |
|
|
RP-35 |
RP-070082 |
0201 |
Performance requirements for 7.68 Mcps E-DCH associated downlink signalling channels: E-AGCH and E-HICH |
B |
7.5.0 |
7.6.0 |
TEI7 |
|
|
RP-35 |
RP-070082 |
0203 |
Corrections & clarifications on 7.68 Mcps TDD MTCH demodulation test case. |
F |
7.5.0 |
7.6.0 |
TEI7 |
|
|
RP-35 |
RP-070085 |
0202 |
Performance requirements for MTCH using 16QAM in an extended delay spread environment |
B |
7.5.0 |
7.6.0 |
MBMSE-RANPhysTDD |
|
|
RP-35 |
RP-070085 |
0211 |
Performance requirement for MCCH in an extended delay spread environment |
B |
7.5.0 |
7.6.0 |
MBMSE-RANPhysTDD |
|
|
RP-36 |
RP-070376 |
0225 |
Performance requirements for MCCH in an extended delay spread environment. |
F |
7.6.0 |
7.7.0 |
MBMSE-RANPhysTDD |
|
|
RP-36 |
RP-070376 |
0212 |
1 |
MCCH & MTCH Channels Performances in TDD MBSFN |
B |
7.6.0 |
7.7.0 |
MBMSE-RANPhysTDD |
|
RP-36 |
RP-070376 |
0224 |
1 |
Performance requirements for MTCH using 16QAM in an extended delay spread environment. |
F |
7.6.0 |
7.7.0 |
MBMSE-RANPhysTDD |
|
RP-36 |
RP-070376 |
0213 |
1 |
Performance requirement for MTCH in a MBSFN TDD UE sharing the same platform with a FDD UE |
B |
7.6.0 |
7.7.0 |
MBMSE-RANPhysTDD |
|
RP-36 |
RP-070377 |
0223 |
1 |
Performance requirements for 1.28 Mcps E-DCH associated downlink signalling channels: E-AGCH and E-HICH |
B |
7.6.0 |
7.7.0 |
LCRTDD-EDCH-RF |
|
RP-36 |
RP-070373 |
0222 |
1 |
Updating of HSDPA demodulation performance requirements for 1.28Mcps TDD |
A |
7.6.0 |
7.7.0 |
TEI7 |
|
RP-36 |
RP-070373 |
0216 |
Updating of HSDPA demodulation performance requirements for 1.28Mcps TDD-FRC |
A |
7.6.0 |
7.7.0 |
TEI7 |
|
|
RP-36 |
RP-070373 |
0219 |
Updating of HSDPA demodulation performance requirements for 1.28Mcps TDD-VRC |
A |
7.6.0 |
7.7.0 |
TEI7 |
|
|
RP-37 |
RP-070651 |
0243 |
Change to HSDPA for 1.28 Mcps TDD |
F |
7.7.0 |
7.8.0 |
TEI7 |
|
|
RP-37 |
RP-070651 |
0240 |
Correction of UE maximum output power classes for 1.28 Mcps TDD option |
F |
7.7.0 |
7.8.0 |
TEI7 |
|
|
RP-37 |
RP-070651 |
0230 |
Inclusion of 7.68 Mcps in the scope of document |
D |
7.7.0 |
7.8.0 |
TEI7 |
|
|
RP-37 |
RP-070651 |
0232 |
Clarification of MBMS test for LCR TDD |
A |
7.7.0 |
7.8.0 |
TEI7 |
|
|
RP-37 |
RP-070652 |
0229 |
Requirements for maximum Input level for HS-PDSCH reception |
A |
7.7.0 |
7.8.0 |
TEI7 |
|
|
RP-37 |
RP-070654 |
0234 |
Performance Requirements for TDD MBSFN Channels |
B |
7.7.0 |
7.8.0 |
MBMSE-RANPhysTDD |
|
|
RP-38 |
RP-070935 |
0244 |
LCR TDD MBSFN UE demodulation performance requirements |
B |
7.8.0 |
7.9.0 |
MBMSE-RANPhysLCRTDD |
|
|
RP-38 |
RP-070937 |
0245 |
Relative delay corrections in Extended Delay Spread propagation condition |
F |
7.8.0 |
7.9.0 |
TEI7 |
|
|
RP-39 |
RP-080118 |
0250 |
Adding EVM requirement for UL 16QAM |
F |
7.9.0 |
7.10.0 |
LCRTDD-EDCH-RF |
|
|
RP-39 |
RP-080118 |
0251 |
1 |
Adding requirements for MBSFN capable UE (dedicated carrier case) |
F |
7.9.0 |
7.10.0 |
MBMS-RANPhysLCRTDD |
|
RP-39 |
RP-080119 |
0246 |
Omissions of minimum requirements for blocking characteristics |
F |
7.9.0 |
7.10.0 |
TEI6 |
|
|
RP-39 |
RP-080119 |
0249 |
Deleting redundant notes for receiver spurious emissions |
F |
7.9.0 |
7.10.0 |
TEI6 |
|
|
RP-40 |
RP-080324 |
0263 |
Clarification of MCCH Physical Channel for MBSFN |
F |
7.10.0 |
7.11.0 |
MBMSE-RANPhysTDD |
|
|
RP-40 |
RP-080324 |
0262 |
Correction to MTCH parameters for demodulation test in TDD MBSFN |
F |
7.10.0 |
7.11.0 |
MBMSE-RANPhysTDD |
|
|
RP-40 |
RP-080324 |
0257 |
Corrections for LCR TDD MBMS |
F |
7.10.0 |
7.11.0 |
MBMSE-RANPhysTDD |
|
|
RP-40 |
RP-080324 |
0256 |
MBSFN Reference Channel |
F |
7.10.0 |
7.11.0 |
MBMSE-RANPhysTDD |
|
|
RP-40 |
RP-080384 |
0260 |
UMTS2.3 GHz TDD: UE receiver characteristics & propagation conditions for 1.28Mcps TDD |
B |
7.11.0 |
8.0.0 |
RinImp8-UMTS2300TDD |
|
|
RP-40 |
RP-080384 |
0259 |
UMTS2.3 GHz TDD: UE transmitter Characteristics for 2.3GHz LCR TDD |
B |
7.11.0 |
8.0.0 |
RinImp8-UMTS2300TDD |
|
|
RP-40 |
RP-080384 |
0258 |
New band introduction for 25.102 |
B |
7.11.0 |
8.0.0 |
RinImp8-UMTS2300TDD |
|
|
RP-41 |
RP-080 |
270 |
Demodulation requirements of fixed reference channels for 1.28Mcps TDD option 64QAM DL |
F |
8.0.0 |
8.1.0 |
RANimp-64Qam1.28TDD |
|
|
RP-41 |
RP-080628 |
0269 |
RF requirements in later releases |
A |
8.0.0 |
8.1.0 |
RinImp8-UMTS2300TDD |
|
|
RP-41 |
RP-080628 |
0264 |
1 |
UE RF capabilitiy information update |
F |
8.0.0 |
8.1.0 |
RinImp8-UMTS2300TDD |
|
RP-42 |
RP-080899 |
0279 |
1 |
UE reference measurement channel and performance requirement for 384kbps service |
A |
8.1.0 |
8.2.0 |
TEI4 |
|
RP-42 |
RP-080939 |
0280 |
Introduction of band 1880-1920MHz for 25.102 |
B |
8.1.0 |
8.2.0 |
Rimp9-UMTS1880TDD |
|
|
RP-42 |
RP-080946 |
0281 |
Adding the demodulation requirements for 1.28Mcps TDD Option 64QAM DL. |
B |
8.1.0 |
8.2.0 |
RANimp-64Qam1.28TDD |
|
|
RP-42 |
RP-080946 |
0282 |
Adding the requirement of maximum input level for 1.28Mcps TDD option 64QAM DL |
B |
8.1.0 |
8.2.0 |
RANimp-64Qam1.28TDD |
|
|
RP-42 |
RP-080941 |
0273 |
Additional minimum requirements for LCR TDD UE Adjacent Channel Selectivity |
F |
8.1.0 |
8.2.0 |
TEI8 |
|
|
RP-43 |
RP-090169 |
0288 |
Correction on MBSFN MCCH Slot Format |
A |
8.2.0 |
8.3.0 |
MBMSE-RANPhysTDD |
|
|
RP-43 |
RP-090169 |
0284 |
Correction on MBSFN MCCH Slot Format |
F |
8.2.0 |
8.3.0 |
TEI7 |
|
|
RP-43 |
RP-090194 |
0289 |
Introduction of 3.84Mcps TDD MBSFN IMB |
B |
8.2.0 |
8.3.0 |
MBSFN-DOB |
|
|
RP-43 |
RP-090197 |
0285 |
UMTS1880MHz: Transmitter spurious emission |
F |
8.2.0 |
8.3.0 |
Rlnlmp9-UMTS1880TDD |
|
|
RP-43 |
RP-090197 |
0286 |
UMTS1880MHz: Receiver characteristic and propagation condition for UE |
F |
8.2.0 |
8.3.0 |
Rlnlmp9-UMTS1880TDD |
|
|
RP-44 |
RP-090539 |
0300 |
Correction concerning scope of applicability for Extended Delay Spread propagation conditions |
A |
8.3.0 |
8.4.0 |
MBMSE-RANPhysTDD |
|
|
RP-44 |
RP-090554 |
0290 |
HS-DSCH performance requirements for 1.28Mcps TDD MIMO |
F |
8.3.0 |
8.4.0 |
RANimp-LCRMIMO |
|
|
RP-44 |
RP-090554 |
0291 |
HS-SCCH performance requirements for 1.28Mcps TDD MIMO |
F |
8.3.0 |
8.4.0 |
RANimp-LCRMIMO |
|
|
RP-44 |
RP-090554 |
0292 |
CQI reporting performance requirements for 1.28Mcps TDD MIMO |
F |
8.3.0 |
8.4.0 |
RANimp-LCRMIMO |
|
|
RP-44 |
RP-090556 |
0294 |
Correction on 64QAM Reference measurement channel for 1.28Mcps TDD. (Technically Endorsed CR in R4-50bis – R4-091184) |
F |
8.3.0 |
8.4.0 |
TEI8 |
|
|
RP-44 |
RP-090557 |
0296 |
Definition of DL reference measurement channel for IMB |
F |
8.3.0 |
8.4.0 |
MBSFN-DOB |
|
|
RP-44 |
RP-090557 |
0295 |
1 |
Accommodation of the IMB reference bearer in the receiver characteristics of clause 7 |
F |
8.3.0 |
8.4.0 |
MBSFN-DOB |
|
RP-44 |
RP-090557 |
0301 |
Addition of Performance Requirements for IMB MCCH |
F |
8.3.0 |
8.4.0 |
MBSFN-DOB |
|
|
RP-44 |
RP-090557 |
0302 |
Addition of Performance Requirements for IMB MTCH |
F |
8.3.0 |
8.4.0 |
MBSFN-DOB |
|
|
RP-44 |
RP-090560 |
0303 |
Addition of new requirement of new E-AGCH type 2 |
B |
8.3.0 |
8.4.0 |
RANimp-LCRCPC |
|
|
RP-45 |
RP-090818 |
0306 |
Correction to TS25.102 defining the abbreviations MCCH and MTCH |
F |
8.4.0 |
8.5.0 |
MBSFN-DOB |
|
|
0307 |
Addition of performance requirements for IMB MTCH |
F |
8.4.0 |
8.5.0 |
MBSFN-DOB |
|||
|
0309 |
1 |
Addition of Performance Requirements for IMB MCCH |
F |
8.4.0 |
8.5.0 |
MBSFN-DOB |
||
|
RP-45 |
RP-090821 |
0305 |
Correction of reference channel for category 29-30 UE |
F |
8.4.0 |
8.5.0 |
RANimp-MIMOLCR |
|
|
0308 |
1 |
Clarification of test configuration for UE with multiple antennas |
F |
8.4.0 |
8.5.0 |
RANimp-MIMOLCR |
||
|
RP-45 |
RP-090825 |
0304 |
Revision of 64QAM Reference channel |
F |
8.4.0 |
8.5.0 |
TEI8 |
|
|
RP-46 |
RP-091285 |
0313 |
|
UE performance requirements in high speed train condition for LCR TDD (Technically endorsed at RAN 4 52bis in R4-093542) |
B |
8.5.0 |
9.0.0 |
RinImp9-LCRTDD350 |
|
RP-47 |
RP-100256 |
0327 |
1 |
Maximum output power with multi-code for TDD |
A |
9.0.0 |
9.1.0 |
TEI7 |
|
RP-47 |
RP-100256 |
0324 |
Demodulation of DCH in moving conditions for TDD |
A |
9.0.0 |
9.1.0 |
TEI7 |
|
|
RP-47 |
RP-100256 |
0321 |
Demodulation of DCH in birth-death conditions for TDD |
A |
9.0.0 |
9.1.0 |
TEI7 |
|
|
RP-47 |
RP-100248 |
0328 |
Modification to IMB receiver characteristic requirements |
A |
9.0.0 |
9.1.0 |
MBSFN-DOB |
|
|
RP-47 |
RP-100273 |
0318 |
Additional performance requirements in high speed train conditions for LCR TDD |
F |
9.0.0 |
9.1.0 |
RinImp9- LCRTDD350 |
|
|
RP-49 |
RP-100913 |
0331 |
Correction of 1.28Mcps TDD spectrum emission mask requirement |
A |
9.1.0 |
9.2.0 |
TEI7 |
|
|
RP-50 |
RP-101326 |
0344 |
|
Introduction of new constant BLER test cases |
A |
9.2.0 |
9.3.0 |
TEI7 |
|
RP-50 |
RP-101339 |
0336 |
1 |
Modification of transport block size to DL reference measurement channel for IMB MBSFN only Ues |
A |
9.2.0 |
9.3.0 |
MBSFN-DOB |
|
RP-50 |
RP-101339 |
0338 |
1 |
Modification of transport block size to performance requirements for demodulation of IMB MBSFN MTCH |
A |
9.2.0 |
9.3.0 |
MBSFN-DOB |
|
RP-50 |
RP-101339 |
0340 |
1 |
Correcting the data rate naming of performance requirements for demodulation of IMB MBSFN MCCH |
A |
9.2.0 |
9.3.0 |
MBSFN-DOB |
|
RP-50 |
RP-101351 |
0341 |
2 |
Introduction of UE requirements for 1.28Mcps TDD MC-HSUPA |
B |
9.3.0 |
10.0.0 |
TDD_MC_HSUPA |
|
RP-51 |
RP-110341 |
00350 |
– |
Correction of Maximum Input Level Test for HS-PDSCH Transmission for 1.28Mcps TDD |
A |
10.0.0 |
10.1.0 |
TEI8 |
|
RP-51 |
RP-110335 |
00354 |
– |
Introduction of new DL power control TC, wind up effects for 1.28Mcps TDD |
A |
10.0.0 |
10.1.0 |
TEI7 |
|
RP-52 |
RP-110798 |
0355 |
|
Introduction of performance requirements for 1.28Mcps TDD MU-MIMO |
B |
10.1.0 |
10.2.0 |
MUMIMO_LCR_TDD-Perf |
|
RP-53 |
RP-111245 |
0359 |
1 |
Introduction of new DL power control TC, initial convergence for 1.28Mcps TDD |
A |
10.2.0 |
10.3.0 |
TEI7 |
|
RP-54 |
RP-111694 |
0361 |
UE demodulation performance requirements under multiple-cell scenario for 1.28Mcps TDD |
F |
10.3.0 |
11.1.0 |
LCR_TDD_UE_demod_mc-Perf |
|
|
RP-56 |
RP-120765 |
0365 |
|
Clarification of the scope of Band a for 1.28 Mcps TDD option |
A |
11.1.0 |
11.2.0 |
TEI8 |
|
RP-56 |
RP-120793 |
0366 |
|
Introduction of Band 44 |
B |
11.1.0 |
11.2.0 |
LTE_APAC700-Core |
|
RP-56 |
RP-120765 |
0370 |
|
Additional spurious emissions requirements for PHS |
A |
11.1.0 |
11.2.0 |
TEI8 |
|
RP-57 |
RP-121296 |
0374 |
|
Correction of frequency band number in Table 5.2 in 25.102 (R11) |
A |
11.2.0 |
11.3.0 |
TEI8 |
|
RP-59 |
RP-130287 |
377 |
|
Update of UE co-existence requirement towards UTRA TDD bands in China |
F |
11.3.0 |
11.4.0 |
TEI11 |
|
RP-59 |
RP-130287 |
376 |
|
Correction of UE co-existence requirement towards UTRA TDD bands in China |
F |
11.3.0 |
11.4.0 |
TEI11 |
|
RP-60 |
RP-130764 |
378 |
Co-existence around 3500 MHz |
F |
11.4.0 |
11.5.0 |
RInImp8-UMTSLTE3500 |
|
|
RP-62 |
RP-131939 |
379 |
|
Receiver spurious emissions corrections |
F |
11.5.0 |
11.6.0 |
TEI11 |
|
SP-65 |
– |
– |
– |
Update to Rel-12 version (MCC) |
– |
11.6.0 |
12.0.0 |
|
|
SP-70 |
– |
– |
– |
Update to Rel-13 version (MCC) |
– |
12.0.0 |
13.0.0 |
|
|
RP-75 |
– |
– |
– |
Update to Rel-14 version (MCC) |
– |
13.0.0 |
14.0.0 |
|
Change history |
|||||||
|
Date |
Meeting |
TDoc |
CR |
Rev |
Cat |
Subject/Comment |
New version |
|
2018-06 |
SA#80 |
– |
– |
– |
– |
Update to Rel-15 version (MCC) |
15.0.0 |
|
2020-06 |
SA#88 |
– |
– |
– |
– |
Update to Rel-16 version (MCC) |
16.0.0 |
|
2022-03 |
SA#95 |
Update to Rel-17 version (MCC) |
17.0.0 |
||||