9.2.1 HS-DSCH throughput for fixed reference channels

25.1023GPPRelease 17TSUser Equipment (UE) radio transmission and reception (TDD)

The performance requirements in this subclause apply for the reference measurement channels specified in Annex A.3.2.

During the Fixed Reference Channel tests the behaviour of the Node-B emulator in response to the ACK/NACK signalling field of the HS-SICH is specified in Table 9.8

Table 9.8: Node-B Emulator Behaviour in response to ACK/NACK/DTX

HS-SICH ACK/NACK Field State

Node-B Emulator Behaviour

ACK

ACK: new transmission using 1st redundancy and constellation version (RV)

NACK

NACK: retransmission using the next RV (up to the maximum permitted number or RV’s)

DTX

DTX: retransmission using the RV previously transmitted to the same H-ARQ process

NOTE: Performance requirements in this section assume a sufficient power allocation to HS-SCCH so that probability of reporting DTX is very low.

9.2.1.1 Category 1, 0.5Mbps UE class

For the parameters specified in Table 9.9, the measured throughput R shall exceed the throughput specified in Table 9.10 for each radio condition.

Table 9.9: Test parameters for fixed reference measurement channel, QPSK

Parameters

Unit

Test 1

Test 2

Test 3

Test 4

HS-PDSCH Modulation

–

QPSK*

Scrambling code and basic midamble code number**

–

1

Number of TS

–

2

HS-PDSCH Channelization Codes*

C(k,Q)

C(i,16)

i=1..10

Number of Hybrid ARQ processes

–

4

Maximum number of Hybrid ARQ transmissions

–

4

Redundancy and constellation version coding sequence

–

{0,0,0,0}

dB

-10

Ioc***

dBm/1.28MHz

-60

* Note Only QPSK is supported for this category UE.

**Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.

***Note: For multi-carrier reception, it refers to the interference power on each carrier.

Table 9.10: Performance requirements for fixed reference channel, QPSK

Test Number

Propagation conditions

[dB](Note1)

R (Throughput) [kbps](Note2)

1

PA3

10

160

2

PB3

10

170

3

VA30

10

161

4

VA120

10

153

Note 1: For multi-carrier reception, it refers to on each carrier.

Note 2: For multi-carrier reception, R refers to throughput on each carrier.

9.2.1.2 Category 4, 1.1Mbps UE class

For the parameters specified in Table 9.9-1, the measured throughput R shall exceed the throughput specified in Table 9.10-1 for each radio condition.

Table 9.9-1: Test parameters for fixed reference measurement channel, 16QAM

Parameters

Unit

Test 1

Test 2

Test 3

Test 4

HS-PDSCH Modulation

–

16QAM

Scrambling code and basic midamble code number*

–

1

Number of TS

–

2

HS-PDSCH Channelization Codes*

C(k,Q)

C(i,16)

i=1..12

Number of Hybrid ARQ processes

–

4

Maximum number of Hybrid ARQ transmissions

–

4

Redundancy and constellation version coding sequence

–

{6,2,1,5}

dB

-10.8

Ioc**

dBm/1.28MHz

-60

*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.

**Note: For multi-carrier reception, it refers to the interference power on each carrier.

Table 9.10-1: Performance requirements for QPSK, fixed reference channel, 16QAM

Test Number

Propagation conditions

[dB](Note1)

R (Throughput) [kbps](Note2)

1

PA3

15

388

2

PB3

15

347

3

VA30

15

316

4

VA120

15

274

Note 1: For multi-carrier reception, it refers to on each carrier.

Note 2: For multi-carrier reception, R refers to throughput on each carrier.

* Note: Test case in 9.2.1.1.1 can be used to test this kind of UE in case of QPSK.

9.2.1.3 Category 7, 1.6Mbps UE class

For the parameters specified in Table 9.9-2, the measured throughput R shall exceed the throughput specified in Table 9.10-2 for each radio condition.

Table 9.9-2: Test parameters for fixed reference measurement channel

Parameters

Unit

Test 1

Test 2

Test 3

Test 4

Test 5

Test 6

Test 7

Test 8

HS-PDSCH Modulation

–

QPSK

16QAM

Scrambling code and basic midamble code number*

–

1

Number of TS

–

3

Number of Hybrid ARQ processes

–

4

Maximum number of Hybrid ARQ transmissions

–

4

HS-PDSCH Channelization Codes*

C(k,Q)

C(i,16)

i=1..10

C(i,16)

i=1..12

Redundancy and constellation version coding sequence

–

{0,0,0,0}

{6,2,1,5}

dB

-10

-10.8

Ioc**

dBm/

1.28MHz

-60

*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.

**Note: For multi-carrier reception, it refers to the interference power on each carrier.

Table 9.10-2: Performance requirements for fixed reference channel

Test Number

Propagation conditions

[dB](Note1)

R (Throughput) [kbps](Note2)

1

PA3

10

270

2

PB3

10

278

3

VA30

10

259

4

VA120

10

242

5

PA3

15

488

6

PB3

15

471

7

VA30

15

431

8

VA120

15

377

Note 1: For multi-carrier reception, it refers to on each carrier.

Note 2: For multi-carrier reception, R refers to throughput on each carrier.

9.2.1.4 Category 10, 2.2Mbps UE class

For the parameters specified in Table 9.9-3, the measured throughput R shall exceed the throughput specified in Table 9.10-3 for each radio condition.

Table 9.9-3: Test parameters for fixed reference measurement channel

Parameters

Unit

Test 1

Test 2

Test 3

Test 4

Test 5

Test 6

Test 7

Test 8

HS-PDSCH Modulation

–

QPSK

16QAM

Scrambling code and basic midamble code number*

–

1

Number of TS

–

4

Number of Hybrid ARQ processes

–

4

Maximum number of Hybrid ARQ transmissions

–

4

HS-PDSCH Channelization Codes*

C(k,Q)

C(i,16)

i=1..10

C(i,16)

i=1..12

Redundancy and constellation version coding sequence

–

{0,0,0,0}

{6,2,1,5}

dB

-10

-10.8

Ioc**

dBm/

1.28MHz

-60

*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.

**Note: For multi-carrier reception, it refers to the interference power on each carrier.

Table 9.10-3: Performance requirements for fixed reference channel

Test Number

Propagation conditions

[dB](Note1)

R (Throughput) [kbps](Note2)

1

PA3

10

360

2

PB3

10

343

3

VA30

10

320

4

VA120

10

275

5

PA3

15

615

6

PB3

15

606

7

VA30

15

554

8

VA120

15

493

Note 1: For multi-carrier reception, it refers to on each carrier.

Note 2: For multi-carrier reception, R refers to throughput on each carrier.

9.2.1.5 Category 13, 2.8Mbps UE class

For the parameters specified in Table 9.9-4, the measured throughput R shall exceed the throughput specified in Table 9.10-4 for each radio condition.

Table 9.9-4: Test parameters for fixed reference measurement channel

Parameters

Unit

Test 1

Test 2

Test 3

Test 4

Test 5

Test 6

Test 7

Test 8

HS-PDSCH Modulation

–

QPSK

16QAM

Scrambling code and basic midamble code number*

–

1

Number of TS

–

5

Number of Hybrid ARQ processes

–

4

Maximum number of Hybrid ARQ transmissions

–

4

HS-PDSCH Channelization Codes*

C(k,Q)

C(i,16)

i=1..10

C(i,16)

i=1..12

Redundancy and constellation version coding sequence

–

{0,0,0,0}

{6,2,1,5}

dB

-10

-10.8

Ioc**

dBm/

1.28MHz

-60

*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.

**Note: For multi-carrier reception, it refers to the interference power on each carrier.

Table 9.10-4: Performance requirements for fixed reference channel

Test Number

Propagation conditions

[dB](Note1)

R (Throughput) [kbps](Note2)

1

PA3

10

461

2

PB3

10

470

3

VA30

10

438

4

VA120

10

409

5

PA3

15

890

6

PB3

15

810

7

VA30

15

730

8

VA120

15

630

Note 1: For multi-carrier reception, it refers to on each carrier.

Note 2: For multi-carrier reception, R refers to throughput on each carrier.

9.2.1.6 Category 16-24

For the parameters specified in Table 9.9-5, the measured throughput R shall exceed the throughput specified in Table 9.10-5 for each reference measurement channel in annex A.3.2.7.

Table 9.9-5: Test parameters for fixed reference measurement channels

Parameters

Unit

Test 1 (Category 16-18)

Test 2 (Category 19-21)

Test 3 (Category 22-24)

HS-PDSCH Modulation

–

64QAM

Scrambling code and basic midamble code number*

–

1

Number of TS

–

3

4

5

Number of Hybrid ARQ processes

–

4

Maximum number of Hybrid ARQ transmissions

–

4

HS-PDSCH Channelization Codes*

C(k,Q)

C(i,16)

i=1..14

Redundancy and constellation version coding sequence

–

{6,5,4,0}

dB

-11.46

Ioc**

dBm/

1.28MHz

-60

*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.

**Note: For multi-carrier reception, it refers to the interference power on each carrier.

Table 9.10-5: Performance requirements for fixed reference measurement channels

Test Number

Propagation conditions

[dB](Note1)

R (Throughput) [kbps](Note2)

1

PA3

18

660

2

PA3

18

875

3

PA3

18

1090

Note 1: For multi-carrier reception, it refers to on each carrier.

Note 2: For multi-carrier reception, R refers to throughput on each carrier.

9.2.1.7 Category 25

The requirements in this section apply when MIMO is configured. If MIMO is not configured, a category 25 UE should have the capability of category 18 according to [2].

For the parameters specified in Table 9.9-6, the measured throughput R shall exceed the throughput specified in Table 9.10-6 for the reference measurement channels in annex A.3.2.10.

For UE supporting Spreading Factor 1 only in dual stream transmission, the number of HS-PDSCH codes per TS should be configured to 1 and the HS-PDSCH_Ec/Ior should be 0dB in dual stream transmission, other parameters and the performance requirements are the same.

Table 9.9-6: Test parameters for fixed reference measurement channels

Parameters

Unit

Test 1

Test 2

Test 3

Test 4

HS-PDSCH Modulation

–

QPSK

16QAM

Scrambling code and basic midamble code number*

–

0

Number of TS

–

3

Number of Hybrid ARQ processes per stream

–

4

Maximum number of Hybrid ARQ transmissions

–

4

HS-PDSCH Channelization Codes*

C(k,Q)

C(i,16)

i=1..16

C(i,16)

i=1..16

Redundancy and constellation version coding sequence

–

{0,0,0,0}

{6,2,1,5}

dB

-12.04

-12.04

Stream Number Configuration

–

Fixed Dual Stream

Fixed Single Stream

(2nd Stream is not used)

Fixed Dual Stream

Fixed Single Stream

(2nd Stream is not used)

Ioc

dBm/ 1.28MHz

-60

*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.

Table 9.10-6: Performance requirements for fixed reference channels

Test Number

Propagation conditions

[dB]

R (Throughput) [kbps]

1

PA3

10

390

2

PA3

6

160

3

PA3

16

860

4

PA3

12

370

9.2.1.8 Category 26

The requirements in this section apply when MIMO is configured. If MIMO is not configured, a category 26 UE should have the capability of category 21 according to [2].

For the parameters specified in Table 9.9-7, the measured throughput R shall exceed the throughput specified in Table 9.10-7 for the reference measurement channels in annex A.3.2.11.

For UE supporting Spreading Factor 1 only in dual stream transmission, the number of HS-PDSCH codes per TS should be configured to 1 and the HS-PDSCH_Ec/Ior should be 0dB in dual stream transmission, other parameters and the performance requirements are the same.

Table 9.9-7: Test parameters for fixed reference measurement channels

Parameters

Unit

Test 1

Test 2

Test 3

Test 4

HS-PDSCH Modulation

–

QPSK

16QAM

Scrambling code and basic midamble code number*

–

0

Number of TS

–

4

Number of Hybrid ARQ processes per stream

–

4

Maximum number of Hybrid ARQ transmissions

–

4

HS-PDSCH Channelization Codes*

C(k,Q)

C(i,16)

i=1..16

C(i,16)

i=1..16

Redundancy and constellation version coding sequence

–

{0,0,0,0}

{6,2,1,5}

dB

-12.04

-12.04

Stream Number Configuration

–

Fixed Dual Stream

Fixed Single Stream

(2nd Stream is not used)

Fixed Dual Stream

Fixed Single Stream

(2nd Stream is not used)

Ioc

dBm/ 1.28MHz

-60

*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.

Table 9.10-7: Performance requirements for fixed reference channels

Test Number

Propagation conditions

[dB]

R (Throughput) [kbps]

1

PA3

10

650

2

PA3

6

220

3

PA3

16

950

4

PA3

12

380

9.2.1.9 Category 27

The requirements in this section apply when MIMO is configured. If MIMO is not configured, a category 27 UE should have the capability of category 24 according to [2].

For the parameters specified in Table 9.9-8, the measured throughput R shall exceed the throughput specified in Table 9.10-8 for the reference measurement channels in annex A.3.2.12.

For UE supporting Spreading Factor 1 only in dual stream transmission, the number of HS-PDSCH codes per TS should be configured to 1 and the HS-PDSCH_Ec/Ior should be 0dB in dual stream transmission, other parameters and the performance requirements are the same.

Table 9.9-8: Test parameters for fixed reference measurement channels

Parameters

Unit

Test 1

Test 2

Test 3

Test 4

HS-PDSCH Modulation

–

QPSK

16QAM

Scrambling code and basic midamble code number*

–

0

Number of TS

–

5

Number of Hybrid ARQ processes per stream

–

4

Maximum number of Hybrid ARQ transmissions

–

4

HS-PDSCH Channelization Codes*

C(k,Q)

C(i,16)

i=1..16

C(i,16)

i=1..16

Redundancy and constellation version coding sequence

–

{0,0,0,0}

{6,2,1,5}

dB

-12.04

-12.04

Stream Number Configuration

–

Fixed Dual Stream

Fixed Single Stream

(2nd Stream is not used)

Fixed Dual Stream

Fixed Single Stream

(2nd Stream is not used)

Ioc

dBm/ 1.28MHz

-60

*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.

Table 9.10-8: Performance requirements for fixed reference channels

Test Number

Propagation conditions

[dB]

R (Throughput) [kbps]

1

PA3

10

850

2

PA3

6

280

3

PA3

16

1200

4

PA3

12

500

9.2.1.10 Category 28

For the parameters specified in Table 9.9-9, the measured throughput R shall exceed the throughput specified in Table 9.10-9 for the reference measurement channels in annex A.3.2.13.

For UE supporting Spreading Factor 1 only in dual stream transmission, the number of HS-PDSCH codes per TS should be configured to 1 and the HS-PDSCH_Ec/Ior should be 0dB in dual stream transmission, other parameters and the performance requirements are the same.

Table 9.9-9: Test parameters for fixed reference measurement channels

Parameters

Unit

Test 1

Test 2

HS-PDSCH Modulation

–

64QAM

Scrambling code and basic midamble code number*

–

0

Number of TS

–

3

Number of Hybrid ARQ processes per stream

–

4

Maximum number of Hybrid ARQ transmissions

–

4

HS-PDSCH Channelization Codes*

C(k,Q)

C(i,16)

i=1..16

Redundancy and constellation version coding sequence

–

{6,5,4,0}

dB

-12.04

Stream Number Configuration

–

Fixed Dual Stream

Fixed Single Stream

(2nd Stream is not used)

Ioc

dBm/ 1.28MHz

-60

*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.

Table 9.10-9: Performance requirements for fixed reference channels

Test Number

Propagation conditions

[dB]

R (Throughput) [kbps]

1

PA3

20

800

2

PA3

18

540

9.2.1.11 Category 29

For the parameters specified in Table 9.9-10, the measured throughput R shall exceed the throughput specified in Table 9.10-10 for the reference measurement channels in annex A.3.2.14.

For UE supporting Spreading Factor 1 only in dual stream transmission, the number of HS-PDSCH codes per TS should be configured to 1 and the HS-PDSCH_Ec/Ior should be 0dB in dual stream transmission, other parameters and the performance requirements are the same.

Table 9.9-10: Test parameters for fixed reference measurement channels

Parameters

Unit

Test 1

Test 2

HS-PDSCH Modulation

–

64QAM

Scrambling code and basic midamble code number*

–

0

Number of TS

–

4

Number of Hybrid ARQ processes per stream

–

4

Maximum number of Hybrid ARQ transmissions

–

4

HS-PDSCH Channelization Codes*

C(k,Q)

C(i,16)

i=1..16

Redundancy and constellation version coding sequence

–

{6,5,4,0}

dB

-12.04

Stream Number Configuration

–

Fixed Dual Stream

Fixed Single Stream

(2nd Stream is not used)

Ioc

dBm/ 1.28MHz

-60

*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.

Table 9.10-10: Performance requirements for fixed reference channels

Test Number

Propagation conditions

[dB]

R (Throughput) [kbps]

1

PA3

20

1200

2

PA3

18

780

9.2.1.12 Category 30

For the parameters specified in Table 9.9-11, the measured throughput R shall exceed the throughput specified in Table 9.10-11 for the reference measurement channels in annex A.3.2.15.

For UE supporting Spreading Factor 1 only in dual stream transmission, the number of HS-PDSCH codes per TS should be configured to 1 and the HS-PDSCH_Ec/Ior should be 0dB in dual stream transmission, other parameters and the performance requirements are the same.

Table 9.9-11: Test parameters for fixed reference measurement channels

Parameters

Unit

Test 1

Test 2

HS-PDSCH Modulation

–

64QAM

Scrambling code and basic midamble code number*

–

0

Number of TS

–

5

Number of Hybrid ARQ processes per stream

–

4

Maximum number of Hybrid ARQ transmissions

–

4

HS-PDSCH Channelization Codes*

C(k,Q)

C(i,16)

i=1..16

Redundancy and constellation version coding sequence

–

{6,5,4,0}

dB

-12.04

Stream Number Configuration

–

Fixed Dual Stream

Fixed Single Stream

(2nd Stream is not used)

Ioc

dBm/ 1.28MHz

-60

*Note: Refer to TS 25.223 for definition of channelization codes, scrambling code and basic midamble code.

Table 9.10-11: Performance requirements for fixed reference channels

Test Number

Propagation conditions

[dB]

R (Throughput) [kbps]

1

PA3

20

1570

2

PA3

18

1000