E.2 List of UARFCN used for UTRA FDD bands
25.1013GPPRelease 17TSUser Equipment (UE) radio transmission and reception (FDD)
The UARFCN numbering scheme detailed in clauses 5.4.3 and 5.4.4 of this specification is summarized for information in Table E.1. The table shows the UARFCN assigned to all UTRA FDD operating bands, starting with the lowest UARFCN and continuing up to the highest one assigned.
Each band may have two table entries, one for the “general” numbers and one for the “additional” ones, as specified in Table 5.2. The entries in Table E.1 are explained as follows:
Band range: The size of the frequency range for the UTRA FDD band specified in Table 5.0.
Range res.: The size of the frequency range corresponding to the UARFCN range that has been “reserved” in 3GPP for possible future extensions of the band.
Formula offset: The offset parameter (FUL_Offset or FDL_Offset) in the formula, used to calculate the UARFCN as specified in Clause 5.4.3.
Assigned/reserved: Indicates the significance of the UARFCN and corresponding frequencies listed as follows:
Start res. Start of the UARFCN range reserved for the band.
Min. The lowest UARFCN assigned to the band.
Max. The highest UARFCN assigned to the band.
End res. End of the UARFCN range reserved for the band.
NU, ND: Uplink and downlink UARFCN.
FUL, FDL: Corresponding uplink and downlink frequencies.
(Add.): Refers to the additional UARFCN (on the 100 kHz raster) as specified in Table 5.1A.
Note that bands V and VI are shown with common entries in Table E.1, since their UARFCN ranges are completely overlapping.
Table E.1: UARFCN used for the UTRA FDD bands
Uplink UARFCN |
Downlink UARFCN |
|||||||||
UTRA FDD Band |
Band range [MHz] |
Range res. [MHz] |
Formula offset FUL_Offset [MHz] |
Assigned/Reserved |
NU |
FUL [MHz] |
Formula offset FDL_Offset [MHz] |
Assigned/Reserved |
ND |
FDL [MHz] |
II (Add.) |
2×60 |
2×60 |
1850.1 |
Start res. |
0 |
1850.1 |
1850.1 |
Start res. |
400 |
1930.1 |
Min. |
12 |
1852.5 |
Min. |
412 |
1932.5 |
|||||
Max. |
287 |
1907.5 |
Max. |
687 |
1987.5 |
|||||
End res. |
299 |
1909.9 |
End res. |
699 |
1989.9 |
|||||
XIX |
2×15 |
2×15 |
770 |
Start res. |
300 |
830.0 |
735 |
Start res. |
700 |
875.0 |
Min. |
312 |
832.4 |
Min. |
712 |
877.4 |
|||||
Max. |
363 |
842.6 |
Max. |
763 |
887.6 |
|||||
End res. |
374 |
844.8 |
End res. |
774 |
889.8 |
|||||
XIX (Add.) |
2×15 |
2×15 |
755.1 |
Start res. |
375 |
830.1 |
720.1 |
Start res. |
775 |
875.1 |
Min. |
387 |
832.5 |
Min. |
787 |
877.5 |
|||||
Max. |
437 |
842.5 |
Max. |
837 |
887.5 |
|||||
End res. |
449 |
844.9 |
End res. |
849 |
889.9 |
|||||
XXI |
2×15 |
2×15 |
1358 |
Start res. |
450 |
1448.0 |
1326 |
Start res. |
850 |
1496.0 |
Min. |
462 |
1450.4 |
Min. |
862 |
1498.4 |
|||||
Max. |
512 |
1460.4 |
Max. |
912 |
1508.4 |
|||||
End res. |
524 |
1462.8 |
End res. |
924 |
1510.8 |
|||||
V (Add.) |
2×25 (V) 2×10 (VI) |
2×25 |
670.1 |
Start res. |
770 |
824.1 |
670.1 |
Start res. |
995 |
869.1 |
Min. (V) |
782 |
826.5 |
Min. (V) |
1007 |
871.5 |
|||||
Min. (VI) |
812 |
832.5 |
Min. (VI) |
1037 |
877.5 |
|||||
Max. (VI) |
837 |
837.5 |
Max. (VI) |
1062 |
882.5 |
|||||
Max. (V) |
862 |
842.5 |
Max. (V) |
1087 |
887.5 |
|||||
End res. |
894 |
848.9 |
End res. |
1119 |
893.9 |
|||||
III |
2×75 |
2×75 |
1525 |
Start res. |
925 |
1710.0 |
1575 |
Start res. |
1150 |
1805.0 |
Min. |
937 |
1712.4 |
Min. |
1162 |
1807.4 |
|||||
Max. |
1288 |
1782.6 |
Max. |
1513 |
1877.6 |
|||||
End res. |
1299 |
1784.8 |
End res. |
1524 |
1879.8 |
|||||
IV |
2×45 |
2×45 |
1450 |
Start res. |
1300 |
1710.0 |
1805 |
Start res. |
1525 |
2110.0 |
Min. |
1312 |
1712.4 |
Min. |
1537 |
2112.4 |
|||||
Max. |
1513 |
1752.6 |
Max. |
1738 |
2152.6 |
|||||
End res. |
1524 |
1754.8 |
End res. |
1749 |
2154.8 |
|||||
IV |
2×45 |
2×45 |
1380.1 |
Start res. |
1650 |
1710.1 |
1735.1 |
Start res. |
1875 |
2110.1 |
Min. |
1662 |
1712.5 |
Min. |
1887 |
2112.5 |
|||||
Max. |
1862 |
1752.5 |
Max. |
2087 |
2152.5 |
|||||
End res. |
1874 |
1754.9 |
End res. |
2099 |
2154.9 |
|||||
VII |
2×70 |
2×70 |
2100 |
Start res. |
2000 |
2500.0 |
2175 |
Start res. |
2225 |
2620.0 |
Min. |
2012 |
2502.4 |
Min. |
2237 |
2622.4 |
|||||
Max. |
2338 |
2567.6 |
Max. |
2563 |
2687.6 |
|||||
End res. |
2349 |
2569.8 |
End res. |
2574 |
2689.8 |
|||||
VII |
2×70 |
2×70 |
2030.1 |
Start res. |
2350 |
2500.1 |
2105.1 |
Start res. |
2575 |
2620.1 |
Min. |
2362 |
2502.5 |
Min. |
2587 |
2622.5 |
|||||
Max. |
2687 |
2567.5 |
Max. |
2912 |
2687.5 |
|||||
End res. |
2699 |
2569.9 |
End res. |
2924 |
2689.9 |
|||||
VIII |
2×35 |
2×35 |
340 |
Start res. |
2700 |
880.0 |
340 |
Start res. |
2925 |
925.0 |
Min. |
2712 |
882.4 |
Min. |
2937 |
927.4 |
|||||
Max. |
2863 |
912.6 |
Max. |
3088 |
957.6 |
|||||
End res. |
2874 |
914.8 |
End res. |
3099 |
959.8 |
|||||
X |
2×60 |
2×60 |
1135 |
Start res. |
2875 |
1710.0 |
1490 |
Start res. |
3100 |
2110.0 |
Min. |
2887 |
1712.4 |
Min. |
3112 |
2112.4 |
|||||
Max. |
3163 |
1767.6 |
Max. |
3388 |
2167.6 |
|||||
End res. |
3174 |
1769.8 |
End res. |
3399 |
2169.8 |
|||||
X |
2×60 |
2×60 |
1075.1 |
Start res. |
3175 |
1710.1 |
1430.1 |
Start res. |
3400 |
2110.1 |
Min. |
3187 |
1712.5 |
Min. |
3412 |
2112.5 |
|||||
Max. |
3462 |
1767.5 |
Max. |
3687 |
2167.5 |
|||||
End res. |
3474 |
1769.9 |
End res. |
3699 |
2169.9 |
|||||
XI |
2×20 |
2×20 |
733 |
Start res. |
3475 |
1428.0 |
736 |
Start res. |
3700 |
1476.0 |
Min. |
3487 |
1430.4 |
Min. |
3712 |
1478.4 |
|||||
Max. |
3562 |
1445.4 |
Max. |
3787 |
1493.4 |
|||||
End res. |
3574 |
1447.8 |
End res. |
3799 |
1495.8 |
|||||
XII |
2×17 |
2×17 |
-22 |
Start res. |
3605 |
699.0 |
-37 |
Start res. |
3830 |
729.0 |
Min. |
3617 |
701.4 |
Min. |
3842 |
731.4 |
|||||
Max. |
3678 |
713.6 |
Max. |
3903 |
743.6 |
|||||
End res. |
3689 |
715.8 |
End res. |
3914 |
745.8 |
|||||
XII (Add.) |
2×17 |
2×17 |
-39.9 |
Start res. |
3695 |
699.1 |
-54.9 |
Start res. |
3920 |
729.1 |
Min. |
3707 |
701.5 |
Min. |
3932 |
731.5 |
|||||
Max. |
3767 |
713.5 |
Max. |
3992 |
743.5 |
|||||
End res. |
3779 |
715.9 |
End res. |
4004 |
745.9 |
|||||
XIII |
2×10 |
2×10 |
21 |
Start res. |
3780 |
777.0 |
-55 |
Start res. |
4005 |
746.0 |
Min. |
3792 |
779.4 |
Min. |
4017 |
748.4 |
|||||
Max. |
3818 |
784.6 |
Max. |
4043 |
753.6 |
|||||
End res. |
3829 |
786.8 |
End res. |
4054 |
755.8 |
|||||
XIII (Add.) |
2×10 |
2×10 |
11.1 |
Start res. |
3830 |
777.1 |
-64.9 |
Start res. |
4055 |
746.1 |
Min. |
3842 |
779.5 |
Min. |
4067 |
748.5 |
|||||
Max. |
3867 |
784.5 |
Max. |
4092 |
753.5 |
|||||
End res. |
3879 |
786.9 |
End res. |
4104 |
755.9 |
|||||
XIV |
2×10 |
2×10 |
12 |
Start res. |
3880 |
788.0 |
-63 |
Start res. |
4105 |
758.0 |
Min. |
3892 |
790.4 |
Min. |
4117 |
760.4 |
|||||
Max. |
3918 |
795.6 |
Max. |
4143 |
765.6 |
|||||
End res. |
3929 |
797.8 |
End res. |
4154 |
767.8 |
|||||
XIV (Add.) |
2×10 |
2×10 |
2.1 |
Start res. |
3930 |
788.1 |
-72.9 |
Start res. |
4155 |
758.1 |
Min. |
3942 |
790.5 |
Min. |
4167 |
760.5 |
|||||
Max. |
3967 |
795.5 |
Max. |
4192 |
765.5 |
|||||
End res. |
3979 |
797.9 |
End res. |
4204 |
767.9 |
|||||
V |
2×25 (V) 2×10 (VI) |
2×25 |
0 |
Start res. |
4120 |
824.0 |
0 |
Start res. |
4345 |
869.0 |
Min. (V) |
4132 |
826.4 |
Min. (V) |
4357 |
871.4 |
|||||
Min. (VI) |
4162 |
832.4 |
Min. (VI) |
4387 |
877.4 |
|||||
Max. (VI) |
4188 |
837.6 |
Max. (VI) |
4413 |
882.6 |
|||||
Max. (V) |
4233 |
846.6 |
Max. (V) |
4458 |
891.6 |
|||||
End res. |
4244 |
848.8 |
End res. |
4469 |
893.8 |
|||||
XX |
2×30 |
2×30 |
-23 |
Start res. |
4275 |
832.0 |
-109 |
Start res. |
4500 |
791.0 |
Min. |
4287 |
834.4 |
Min. |
4512 |
793.4 |
|||||
Max. |
4413 |
859.6 |
Max. |
4638 |
818.6 |
|||||
End res. |
4424 |
861.8 |
End res. |
4649 |
820.8 |
|||||
XXII |
80 |
80 |
2525 |
Start res. |
4425 |
3410.0 |
2580 |
Start res. |
4650 |
3510.0 |
Min. |
4437 |
3412.4 |
Min. |
4662 |
3512.4 |
|||||
Max. |
4813 |
3487.6 |
Max. |
5038 |
3587.6 |
|||||
Stop res. |
4824 |
3489.8 |
Stop res. |
5049 |
3589.8 |
|||||
XXV |
2×65 |
2×65 |
875 |
Start res. |
4875 |
1850 |
910 |
Start res. |
5100 |
1930 |
Min. |
4887 |
1852.4 |
Min. |
5112 |
1932.4 |
|||||
Max. |
5188 |
1912.6 |
Max. |
5413 |
1992.6 |
|||||
End res. |
5199 |
1914.8 |
End res. |
5424 |
1994.8 |
|||||
XXV (Add.) |
2×65 |
2×65 |
639.1 |
Start res. |
6055 |
1850.1 |
674.1 |
Start res. |
6280 |
1930.1 |
Min. |
6067 |
1852.5 |
Min. |
6292 |
1932.5 |
|||||
Max. |
6367 |
1912.5 |
Max. |
6592 |
1992.5 |
|||||
End res. |
6379 |
1914.9 |
End res. |
6604 |
1994.9 |
|||||
XXVI |
2×35 |
2×35 |
-291 |
Start res. |
5525 |
814.0 |
-291 |
Start res. |
5750 |
859.0 |
Min. |
5537 |
816.4 |
Min. |
5762 |
861.4 |
|||||
Max. |
5688 |
846.6 |
Max. |
5913 |
891.6 |
|||||
End res. |
5699 |
848.8 |
End res. |
5924 |
893.8 |
|||||
XXVI (Add.) |
2×35 |
2×35 |
-325.9 |
Start res |
5700 |
814.1 |
-325.9 |
Start res |
5925 |
859.1 |
Min. |
5712 |
816.5 |
Min. |
5937 |
861.5 |
|||||
Max. |
5862 |
846.5 |
Max. |
6087 |
891.5 |
|||||
End res. |
5874 |
848.9 |
End res. |
6099 |
893.9 |
|||||
XXXII |
44 |
44 |
N/A |
131 |
Start res |
6605 |
1452.0 |
|||
Min. |
6617 |
1454.4 |
||||||||
Max. |
6813 |
1493.6 |
||||||||
End res. |
6824 |
1495.8 |
||||||||
XXXII (Add.) |
44 |
44 |
N/A |
87.1 |
Start res |
6825 |
1452.1 |
|||
Min. |
6637 |
1454.5 |
||||||||
Max. |
7012 |
1489.5 |
||||||||
End res. |
7024 |
1491.9 |
||||||||
IX |
2×35 |
2×35 |
0 |
Start res. |
8750 |
1750.0 |
0 |
Start res. |
9225 |
1845.0 |
Min. |
8762 |
1752.4 |
Min. |
9237 |
1847.4 |
|||||
Max. |
8912 |
1782.4 |
Max. |
9387 |
1877.4 |
|||||
End res. |
8924 |
1784.8 |
End res. |
9399 |
1879.8 |
|||||
II |
2×60 |
2×60 |
0 |
Start res. |
9250 |
1850.0 |
0 |
Start res. |
9650 |
1930.0 |
Min. |
9262 |
1852.4 |
Min. |
9662 |
1932.4 |
|||||
Max. |
9538 |
1907.6 |
Max. |
9938 |
1987.6 |
|||||
End res. |
9549 |
1909.8 |
End res. |
9949 |
1989.8 |
|||||
I |
2×60 |
2×60 |
0 |
Start res. |
9600 |
1920.0 |
0 |
Start res. |
10550 |
2110.0 |
Min. |
9612 |
1922.4 |
Min. |
10562 |
2112.4 |
|||||
Max. |
9888 |
1977.6 |
Max. |
10838 |
2167.6 |
|||||
End res. |
9899 |
1979.8 |
End res. |
10849 |
2169.8 |
Annex F (informative):
Change history
Date |
Meeting |
TDoc |
CR |
Rev |
Cat |
Subject/Comment |
New version |
RP-37 |
Rel-7 version created based on v7.9.0 |
8.0.0 |
|||||
RP-37 |
RP-070658 |
0567 |
B |
Introduction of UMTS1500 requirements (Rel-8) |
8.0.0 |
||
RP-37 |
RP-070654 |
0571 |
1 |
B |
MBSFN FDD UE dem req |
8.0.0 |
|
RP-38 |
RP-070934 |
0578 |
A |
Correction to UE Relative code domain power accuracy |
8.1.0 |
||
RP-38 |
RP-070934 |
0580 |
1 |
A |
Introduction of requirements for UE capable of receiving HS-DSCH and HS-SCCH in CELL_FACH state |
8.1.0 |
|
RP-38 |
RP-070936 |
0576 |
A |
Editorial correction to the RV sequence of the MIMO FRC |
8.1.0 |
||
RP-38 |
RP-070937 |
0575 |
A |
Correction to extreme condition voltages for Lithium batteries in table D.2.2 |
8.1.0 |
||
RP-39 |
RP-080121 |
0593 |
A |
Correct reference to MIMO dual-stream channel model for MIMO CQI dual-stream requirements |
8.2.0 |
||
RP-39 |
RP-080121 |
0594 |
A |
HS-SCCH Type nominator |
8.2.0 |
||
RP-39 |
RP-080121 |
0592 |
1 |
A |
Nominal Peak Data Rate and redundancy versions in MIMO FRC Tests |
8.2.0 |
|
RP-39 |
RP-080124 |
0583 |
2 |
B |
Introduction of UMTS700EMC requirements |
8.2.0 |
|
RP-39 |
RP-080165 |
0598 |
B |
Addition of 15 code HSDPA demodulation requirements for 16QAM and QPSK |
8.2.0 |
||
RP-39 |
RP-080166 |
0582 |
1 |
B |
Specification of enhanced performance requirements type 3i for HSDPA based on receiver diversity and interference-aware chip level equaliser |
8.2.0 |
|
RP-39 |
RP-080167 |
0595 |
A |
Correct reference to H-Set for 64-QAM max input test |
8.2.0 |
||
RP-40 |
RP-080326 |
0606 |
F |
Correction of UMTS700 UE blocking and intermodulation values |
8.3.0 |
||
RP-40 |
RP-080328 |
0608 |
2 |
B |
Introduction of Cat 19-20 demodulation requirement and cleanup of HS-DSCH requirement applicability. |
8.3.0 |
|
RP-40 |
RP-080323 |
0600 |
A |
Correction to MIMO propagation conditions |
8.3.0 |
||
RP-40 |
RP-080323 |
0611 |
A |
HS-DSCH transport Format used for HS-SCCH type 3 requirements |
8.3.0 |
||
RP-40 |
RP-080321 |
0603 |
A |
Correction to Rx Spurious Emissions |
8.3.0 |
||
RP-40 |
RP-080321 |
0601 |
A |
Correction to Annex A.8.1 |
8.3.0 |
||
RP-41 |
RP-080629 |
0618 |
A |
Correction to F-DPCH TPC error rate requirement |
8.4.0 |
||
RP-41 |
RP-080629 |
0621 |
1 |
A |
TS25.101: UTRA UE Power Class |
8.4.0 |
|
RP-41 |
RP-080631 |
0614 |
1 |
F |
CQI reporting test for single link with varying Ior/Ioc |
8.4.0 |
|
RP-41 |
RP-080631 |
0626 |
1 |
F |
MIMO CQI reporting bias tests |
8.4.0 |
|
RP-41 |
RP-080631 |
0627 |
F |
Clarification of HSDPA performance requirement applicability |
8.4.0 |
||
RP-41 |
RP-080625 |
624 |
1 |
F |
CQI reporting test in fading conditions for 64QAM+MIMO |
8.4.0 |
|
RP-42 |
RP-080898 |
635 |
1 |
A |
Introduction of fading CQI requirement at higher geometry for 64QAM operation |
8.5.0 |
|
RP-42 |
RP-080927 |
631 |
1 |
A |
Clarification of HST propagation conditions |
8.5.0 |
|
RP-42 |
RP-080947 |
640 |
1 |
B |
Introduction of E-AI requirements |
8.5.0 |
|
RP-42 |
RP-080948 |
641 |
B |
Introduction of CQI reporting test requirements for DC-HSDPA |
8.5.0 |
||
RP-42 |
RP-080948 |
639 |
3 |
B |
Introduction of DC-HSDPA requirements |
8.5.0 |
|
RP-42 |
RP-080948 |
638 |
4 |
B |
Introduction of FRC requirements for Dual cell HSDPA operation |
8.5.0 |
|
RP-42 |
RP-080942 |
636 |
F |
CQI reporting test for STTD and CL1 with varying Ior/Ioc |
8.5.0 |
||
Correction to version number shown in title line |
8.5.1 |
||||||
RP-043 |
RP-090168 |
644 |
1 |
A |
Correction to requirement tables for 9.2.1 and 9.2.4. |
8.6.0 |
|
RP-043 |
RP-090168 |
648 |
1 |
F |
Dual Cell HSDPA CQI Requirements in AWGN |
8.6.0 |
|
RP-043 |
RP-090168 |
658 |
A |
Correction of HS-SCCH power in CQI tests |
8.6.0 |
||
RP-043 |
RP-090168 |
649 |
1 |
F |
Correction to FRC requirements for DC HSDPA |
8.6.0 |
|
RP-043 |
RP-090168 |
651 |
F |
25.101 CR Tx-Rx frequency separation for DC-HSDPA |
8.6.0 |
||
RP-043 |
RP-090168 |
653 |
F |
25.101 CR clarification of CQI reporting requirement for DC-HSDPA |
8.6.0 |
||
RP-043 |
RP-090196 |
650 |
1 |
F |
25.101 CR E-DCH phase discontinuity test requirement |
8.6.0 |
|
RP-043 |
RP-090196 |
654 |
1 |
F |
Corrections of out of band blocking |
8.6.0 |
|
RP-044 |
RP-090539 |
660 |
A |
Clarifications for CQI Reporting Requirements of HSDPA. (Technically Endorsed CR in R4-50bis – R4-091235) |
8.7.0 |
||
RP-044 |
RP-090539 |
662 |
F |
Correction to MIMO Propagation Conditions. (Technically Endorsed CR in R4-50bis – R4-091433) |
8.7.0 |
||
RP-044 |
RP-090539 |
666 |
1 |
A |
Correction to FRC H-Set 8 definition |
8.7.0 |
|
RP-044 |
RP-090546 |
667 |
F |
Introduction of a new Compressed Mode pattern for E-UTRAN measurements |
8.7.0 |
||
RP-044 |
RP-090555 |
669 |
F |
Removal of square brackets for DC-HSDPA Type 3i demodulation tests |
8.7.0 |
||
RP-044 |
RP-090559 |
661 |
B |
Introduction of Extended UMTS800 requirements |
9.0.0 |
||
RP-45 |
RP-090820 |
673 |
1 |
A |
Update of DC HSDPA CQI requirements |
9.1.0 |
|
RP-46 |
RP-091286 |
676 |
1 |
B |
Introduction of Extended UMTS1500 requirements for TS25.101 (Technically endorsed at RAN 4 52bis in R4-093624) |
9.2.0 |
|
RP-46 |
RP-091290 |
679 |
1 |
B |
Combination of DC-HSDPA and MIMO, CQI requirements (Technically endorsed at RAN 4 52bis in R4-093831) |
9.2.0 |
|
RP-46 |
RP-091290 |
680 |
2 |
B |
Combination of DC-HSDPA and MIMO, FRC requirements (Technically endorsed at RAN 4 52bis in R4-093832) |
9.2.0 |
|
RP-46 |
RP-091290 |
681 |
1 |
B |
Combination of DC-HSDPA and MIMO, RF requirements (Technically endorsed at RAN 4 52bis in R4-093833) |
9.2.0 |
|
RP-46 |
RP-091288 |
682 |
1 |
B |
RF transmitter requirements for DC-HSUPA (Technically endorsed at RAN 4 52bis in R4-094072) |
9.2.0 |
|
RP-46 |
RP-091289 |
683 |
|
B |
25.101 CR introduction of Dual Band DC-HSDPA (Technically Endorsed in R4-52, R4-093464) |
9.2.0 |
|
RP-46 |
RP-091291 |
689 |
2 |
B |
Introduction of requirements for TxAA falback mode |
9.2.0 |
|
RP-46 |
RP-091296 |
690 |
|
A |
Clarification of CQI reporting requirement applicability |
9.2.0 |
|
RP-46 |
RP-091372 |
694 |
A |
RAN5 related changes to enhanced CELL_FACH test case |
9.2.0 |
||
RP-47 |
RP-100248 |
702 |
A |
Correction of H-Set 11 requirement for type 3 and type 3i receivers |
9.3.0 |
||
RP-47 |
RP-100270 |
697 |
F |
Correction of CQI requirements for DC_MIMO |
9.3.0 |
||
RP-47 |
RP-100271 |
703 |
1 |
F |
HS-SCCH requirements for TxAA fallback extension |
9.3.0 |
|
RP-47 |
RP-100263 |
696 |
B |
Introduction of UMTS in 800 MHz for Europe requirements in TS 25.101 |
9.3.0 |
||
RP-47 |
RP-100267 |
699 |
1 |
B |
Tx-Rx frequency separation for DC-HSUPA |
9.3.0 |
|
RP-47 |
RP-100267 |
698 |
2 |
B |
Introduction of Rx core requirements for DC-HSUPA |
9.3.0 |
|
RP-48 |
RP-100624 |
712 |
|
A |
Editorial correction of note in varying geometry testcases |
9.4.0 |
|
RP-48 |
RP-100626 |
704 |
1 |
F |
25.101 CR spurious emission requirements for DC-HSUPA in band XX |
9.4.0 |
|
RP-48 |
RP-100631 |
714 |
1 |
F |
Small correction to parameters for testing MIMO FRC H-Set11/11A |
9.4.0 |
|
RP-48 |
RP-100631 |
713 |
|
F |
DC-MIMO-HSDPA; Removal of brackets from CQI Requirements |
9.4.0 |
|
RP-49 |
RP-100918 |
725 |
A |
Corrections to CQI reporting requirements |
9.5.0 |
||
RP-49 |
RP-100921 |
728 |
F |
Correction to Rx core requirements for DC-HSUPA |
9.5.0 |
||
RP-49 |
RP-100921 |
722 |
F |
Clarification of primary uplink frequency and secondary uplink frequency |
9.5.0 |
||
RP-50 |
RP-101334 |
745 |
|
A |
Correction to Band XII frequency range |
9.6.0 |
|
RP-50 |
RP-101339 |
742 |
1 |
A |
Correction to Downlink Physical Channels in DC-HSDPA Tests |
9.6.0 |
|
RP-50 |
RP-101348 |
751 |
1 |
F |
Correction to core requirements for DB-DC-HSDPA with bands II/IV combination |
9.6.0 |
|
RP-50 |
RP-101348 |
747 |
2 |
F |
Clarification on carrier spacing for DC-HSDPA with MIMO |
9.6.0 |
|
RP-50 |
RP-101353 |
733 |
2 |
B |
Introduction of frequency bands for 4C-HSDPA |
10.0.0 |
|
RP-50 |
RP-101353 |
750 |
1 |
B |
25.101 CR Introduction of Tx Core Requirements for DB-DC-HSDPA and dual band 4C-HSDPA with bands II/IV combination |
10.0.0 |
|
RP-50 |
RP-101353 |
737 |
1 |
B |
25.101 CR introduction of Rx core requirements for 4C-HSDPA |
10.0.0 |
|
RP-50 |
RP-101361 |
748 |
|
B |
Protection of E-UTRA Band 24 |
10.0.0 |
|
Correction of reference to table 7.1aB in section 7.3.1 |
10.0.1 |
||||||
RP-51 |
RP-110354 |
0754 |
1 |
F |
Introduction of Rx core requirements for DB-DC-HSDPA and dual band 4C-HSDPA |
10.1.0 |
|
RP-51 |
RP-110345 |
0765 |
1 |
A |
Correction to Downlink Physical Channels in DC-HSDPA receiver sensitivity |
10.1.0 |
|
RP-51 |
RP-110354 |
0766 |
1 |
F |
Introduction of Tx core requirements for DB-DC-HSDPA and dual band 4C-HSDPA for I/VIII and I/V band combinations |
10.1.0 |
|
RP-51 |
RP-110407 |
0768 |
1 |
B |
HSDPA MIMO demodulation performance requirements due to asymmetric P-CPICH/S-CPICH power settings |
10.1.0 |
|
RP-51 |
RP-110345 |
0771 |
– |
A |
DC-HSUPA Rx core requirements for band XI and band XXI |
10.1.0 |
|
RP-51 |
RP-110341 |
0776 |
– |
A |
Correction of UARFCN range for Band XII |
10.1.0 |
|
RP-51 |
RP-110336 |
0779 |
– |
A |
Correction of OOBB interferer frequency ranges for Band XII |
10.1.0 |
|
RP-51 |
RP-110355 |
0783 |
– |
A |
25.101 CR: Correction of out of band blocking for DB-DC-HSDPA configuration 3 (Rel-10) |
10.1.0 |
|
RP-51 |
RP-110346 |
0785 |
2 |
F |
25.101 CR Introduction of demodulation performance for DB-DC-HSDPA (rel-10) |
10.1.0 |
|
RP-51 |
RP-110355 |
0788 |
3 |
B |
CR for the addition of the new band combinations and the TX core requirements for band I-XI and II-V |
10.1.0 |
|
RP-51 |
RP-110355 |
0789 |
3 |
B |
CR for RX core requirements for band I-XI and II-V |
10.1.0 |
|
RP-51 |
RP-110341 |
0793 |
1 |
A |
CR for the modification of the UE relative code domain power accuracy |
10.1.0 |
|
RP-52 |
RP-110798 |
797 |
|
B |
CR for the introduction of TX core requirements for band I-XI and II-V |
10.2.0 |
|
RP-52 |
RP-110798 |
798 |
|
B |
25.101 CR Introduction of Rx core requirements for Band combinations II-V and I-XI |
10.2.0 |
|
RP-52 |
RP-110801 |
799 |
|
B |
HSDPA MIMO CQI reporting requirements due to asymmetric P-CPICH/S-CPICH power settings |
10.2.0 |
|
RP-52 |
RP-110801 |
811 |
|
B |
HSDPA MIMO CQI reporting requirements due to asymmetric P-CPICH/S-CPICH power settings |
10.2.0 |
|
RP-52 |
RP-110812 |
812 |
|
B |
UTRAN UE spurious emission requirements to protect E-UTRA band 23 |
10.2.0 |
|
RP-52 |
RP-110795 |
813 |
|
F |
UTRAN UE spurious emission requirements to protect E-UTRA band 24 |
10.2.0 |
|
RP-52 |
RP-110796 |
816 |
|
F |
Additional Spurious requirement extension due to EN spec change |
10.2.0 |
|
RP-52 |
RP-110801 |
807 |
1 |
B |
Clarification on retransmission for MIMO workaround |
10.2.0 |
|
RP-52 |
RP-110804 |
805 |
3 |
B |
Expanded 1900 MHz addition to 25.101 |
10.2.0 |
|
RP-53 |
RP-111252 |
846 |
|
A |
Correction of UE Relative code domain power accuracy requirements for TS 25.101 REL-10 |
10.3.0 |
|
RP-53 |
RP-111253 |
843 |
|
A |
Clarification of spectrum emission mask requirements |
10.3.0 |
|
RP-53 |
RP-111254 |
829 |
|
A |
Clarification of ACLR requirements for DC-HSUPA |
10.3.0 |
|
RP-53 |
RP-111255 |
838 |
1 |
B |
Add Band XXII for LTE/UMTS 3500 (FDD) to TS 25.101 |
10.3.0 |
|
RP-53 |
RP-111262 |
837 |
1 |
F |
Fixing UARFCN numbers in 25.101 |
10.3.0 |
|
RP-53 |
RP-111264 |
830 |
1 |
F |
UE core requirements for Band XXV |
10.3.0 |
|
RP-53 |
RP-111270 |
818 |
|
B |
Completion of UE demodulation performance requirements for 4C-HSDPA |
10.3.0 |
|
RP-53 |
RP-111270 |
819 |
1 |
B |
Introduction of UE CQI reporting requirements for 4C-HSDPA |
10.3.0 |
|
RP-54 |
RP-111690 |
848 |
F |
Non applicable UARFCN numbers |
10.4.0 |
||
RP-54 |
RP-111735 |
850 |
F |
Alignment with TS 36.101 on 3500MHz |
10.4.0 |
||
RP-54 |
RP-111686 |
851 |
F |
Introduction of missing ACS case 2 requirement for single band 4C-HSDPA |
10.4.0 |
||
RP-54 |
RP-111696 |
849 |
B |
Introduction of single band 4C-HSDPA II-4 |
11.0.0 |
||
RP-55 |
RP-120306 |
860 |
1 |
B |
Introduction of Band 26/XXVI to TS 25.101 |
11.1.0 |
|
RP-55 |
RP-120297 |
862 |
|
A |
Correction of frequency range for spurious emission requirements |
11.1.0 |
|
RP-56 |
RP-120775 |
866 |
– |
A |
Correction to H-Set 8 |
11.2.0 |
|
RP-56 |
RP-120771 |
874 |
1 |
A |
Introduction of Japanese Regulatory Requirements to W-CDMA Band VIII (R11) |
11.2.0 |
|
RP-56 |
RP-120786 |
876 |
2 |
B |
Introduction of 8C-HSDPA operation in 25.101 and rx core requirements |
11.2.0 |
|
RP-56 |
RP-120793 |
881 |
– |
B |
Introduction of Band 28 |
11.2.0 |
|
RP-56 |
RP-120779 |
883 |
– |
A |
Correction of TX power step size tolerance for HS-DPCCH |
11.2.0 |
|
RP-56 |
RP-120793 |
884 |
1 |
B |
Introduction of Band 44 |
11.2.0 |
|
RP-56 |
RP-120763 |
888 |
– |
A |
Correction to numbers of HS-SCCH for DC-HSDPA |
11.2.0 |
|
RP-56 |
RP-120791 |
889 |
2 |
B |
Introduction of E850_LB (Band 27) to TS 25.101 |
11.2.0 |
|
RP-56 |
RP-120766 |
895 |
– |
A |
Correction of PHS protection requirements for TS 25.101 |
11.2.0 |
|
RP-56 |
RP-120610 |
899 |
2 |
B |
Introduction of non contiguous 4C-HSDPA core requirements definition |
11.2.0 |
|
RP-57 |
RP-121300 |
892a |
– |
A |
Corrections of spurious emission band UE co-existence applicable in Japan |
11.3.0 |
|
RP-57 |
RP-121309 |
899a |
1 |
F |
Missing allowed de-sensitization for single band 4C-HSDPA |
11.3.0 |
|
RP-57 |
RP-121299 |
905 |
1 |
A |
Correction of DC-HSUPA core requirements |
11.3.0 |
|
RP-57 |
RP-121314 |
906 |
1 |
F |
Removal of [] in NC-4C-HSDPA core requirements |
11.3.0 |
|
RP-57 |
RP-121318 |
907 |
1 |
B |
Performance requirements for 8C-HSDPA |
11.3.0 |
|
RP-57 |
RP-121312 |
909 |
– |
A |
DC-HSUPA for Band XXII |
11.3.0 |
|
RP-57 |
RP-121317 |
910 |
– |
B |
Modification of the MPR/CM for 8C-HSDPA |
11.3.0 |
|
RP-57 |
RP-121340 |
911 |
– |
F |
Correction of the HS-DPCCH power step range |
11.3.0 |
|
RP-57 |
RP-121320 |
912 |
– |
B |
Tx requirements for I-2-VIII-2 and II-1-V-2 |
11.3.0 |
|
RP-57 |
RP-121320 |
913 |
1 |
B |
Missing requirements for I-2-VIII-2 and II-1-V-2 |
11.3.0 |
|
RP-58 |
RP-121867 |
927 |
|
A |
Japanese regulatory requirements for DC-HSUPA spurious emissions |
11.4.0 |
|
RP-58 |
RP-121856 |
931 |
|
A |
Alignment of inconsistent Rx core requirements with dual uplinks |
11.4.0 |
|
RP-58 |
RP-121908 |
933 |
1 |
B |
Introduction of UL MIMO to TS 25.101 |
11.4.0 |
|
RP-58 |
RP-121876 |
934 |
1 |
B |
CR to TS 25.101 due to introduction of CLTD |
11.4.0 |
|
RP-58 |
RP-121901 |
935 |
|
B |
Introduction of Band 29 |
11.4.0 |
|
RP-58 |
RP-121876 |
937 |
|
B |
F-TPICH out of quality handling for UL CLTD and UL MIMO |
11.4.0 |
|
RP-58 |
RP-121877 |
918 |
1 |
B |
CR to TS 25.101 due to introduction of OLTD |
11.4.0 |
|
RP-58 |
RP-121848 |
923 |
|
A |
Introducing the additional frequency bands of 5 MHz x 2 in 1.7 GHz in Japan to Band III |
11.4.0 |
|
RP-58 |
RP-121867 |
925 |
|
A |
Cleaning of 25.101 Performance sections Rel-11 The CR was not implemented as it was not based on the latest version of the spec |
11.4.0 |
|
RP-59 |
RP-130287 |
941 |
1 |
F |
CR for Cleaning of 25.101 Rel-11 |
11.5.0 |
|
RP-59 |
RP-130287 |
942 |
1 |
F |
Band 41 requirements for operation in China and Japan |
11.5.0 |
|
RP-59 |
RP-130281 |
940 |
1 |
B |
CR for Non contiguous Carrier aggregation UE demodulation performance |
11.5.0 |
|
RP-59 |
RP-130271 |
939 |
|
F |
Some corrections on requirements of ULTD for TS 25.101 |
11.5.0 |
|
RP-59 |
RP-130270 |
938 |
1 |
F |
Removal of bracket from CR F-TPICH out of quality handling for UL CLTD and UL MIMO |
11.5.0 |
|
RP-60 |
RP-130762 |
948 |
|
A |
Adding definition of UE maximum output power for DC-HSUPA |
11.6.0 |
|
RP-60 |
RP-130762 |
951 |
|
A |
Correction to center frequency offset for additional spectrum emissions mask |
11.6.0 |
|
RP-60 |
RP-130768 |
952 |
|
F |
Correction to Definitions list |
11.6.0 |
|
RP-60 |
RP-130768 |
955 |
1 |
F |
Co-existence with 2.6GHz bands |
11.6.0 |
|
RP-60 |
RP-130768 |
964 |
|
F |
Introduction of F-TPICH demodulation performance requirements in F-TPICH out-of-quality handling requirements |
11.6.0 |
|
RP-60 |
RP-130766 |
967 |
|
A |
Carrier aggregation in multi-RAT UTRA and E-UTRA terminals |
11.6.0 |
|
RP-60 |
RP-130764 |
973 |
|
A |
Editorial CR for 25.101 rel-11 |
11.6.0 |
|
RP-60 |
RP-130791 |
960 |
|
B |
Introduction of Band 30 |
12.0.0 |
|
RP-60 |
RP-130790 |
971 |
|
B |
Protection of LTE 450 band |
12.0.0 |
|
RP-61 |
RP-131280 |
988 |
|
A |
CM and MPR for DC-HSUPA with 16QAM |
12.1.0 |
|
RP-61 |
RP-131304 |
989 |
|
A |
Introduction of UE demodulation performance requirements for Multiflow HSDPA |
12.1.0 |
|
RP-61 |
RP-131304 |
990 |
|
A |
Introduction of UE CQI reporting performance requirements for Multiflow HSDPA |
12.1.0 |
|
RP-62 |
RP-131925 |
1004 |
|
A |
Missing update on reference input power adjustment for a dual band device |
12.2.0 |
|
RP-62 |
RP-131933 |
1010 |
|
A |
CSI testing for MIMO mode with 4 transmit antennas |
12.2.0 |
|
RP-62 |
RP-131932 |
1015 |
|
A |
Introduction of UE requirements for determination of Common E-RGCH Radio Link(s) in Cell_FACH |
12.2.0 |
|
RP-62 |
RP-131967 |
1016 |
|
F |
Band 41 deployment in Japan |
12.2.0 |
|
RP-62 |
RP-131933 |
992 |
|
A |
HS-PDSCH performance requirements for MIMO mode with 4 transmit antennas |
12.2.0 |
|
RP-62 |
RP-131929 |
996 |
|
A |
Clarification on the applicability of MIMO performance for a UE supporting NC-MC-HSDPA |
12.2.0 |
|
RP-63 |
RP-140375 |
1028 |
|
A |
Editorial corrections to UE RF core requirements in TS 25.101 |
12.3.0 |
|
RP-63 |
RP-140369 |
1018 |
|
A |
Removing [] in 25.101 in the context of Four transmit antennas for HSDPA |
12.3.0 |
|
RP-64 |
RP-140926 |
1034 |
2 |
B |
Introduction of Band XXXII and Band I+XXXII |
12.4.0 |
|
RP-64 |
RP-140945 |
1033 |
|
D |
Editorial correction of note in clause 4.4 |
12.4.0 |
|
RP-65 |
RP-141543 |
1040 |
B |
Addition of demodulation requirement for BCH mapped to S-CCPCH |
12.5.0 |
||
RP-65 |
RP-141529 |
1042 |
A |
Maximum allowed UL TX power for Band XXVI coexistence with Public Safety |
12.5.0 |
||
RP-65 |
RP-141238 |
1043 |
B |
CR on UMTS HetNet Enhancements |
12.5.0 |
||
RP-66 |
RP-142168 |
1054 |
|
B |
UMTS HetNet Enhancements requirements for power control |
12.6.0 |
|
RP-66 |
RP-142167 |
1049 |
1 |
B |
25.101 CR on performance requirements for UE DCH demodulation during handover due to introduction of DCH enhancements |
12.6.0 |
|
RP-66 |
RP-142167 |
1051 |
1 |
B |
25.101 CR on performance requirements for UE DCH demodulation in static and multipath fading conditions due to introduction of DCH enhancements |
12.6.0 |
|
RP-66 |
RP-142170 |
1053 |
1 |
B |
25.101 CR on E-AGCH performance requirements with TDM granting |
12.6.0 |
|
RP-66 |
RP-142188 |
1059 |
1 |
F |
TS25.101 removal of brackets (RF) |
12.6.0 |
|
RP-66 |
RP-142153 |
1055 |
1 |
F |
UMTS HetNet Enhancements impact on cubic metric (MPR) |
12.6.0 |
|
RP-66 |
RP-142167 |
1048 |
2 |
B |
25.101 CR on new reference measurement channels due to introduction of DCH enhancements |
12.6.0 |
|
RP-66 |
RP-142167 |
1050 |
2 |
B |
25.101 CR on performance requirements for downlink power control due to introduction of DCH enhancements |
12.6.0 |
|
RP-67 |
RP-150385 |
1060 |
F |
TX UE spurious emissions alignment with 36.101 |
12.7.0 |
||
RP-67 |
RP-150385 |
1061 |
F |
RX UE spurious emissions simplification |
12.7.0 |
||
RP-67 |
RP-150385 |
1062 |
F |
Removal of square brackets of cubic metric (MPR) for UMTS HetNet Enhancements |
12.7.0 |
||
RP-68 |
RP-150957 |
1067 |
F |
Receiver spurious emissions requirements for downlink-only bands (Band XXXII) |
12.8.0 |
||
RP-69 |
RP-151483 |
1070 |
1 |
F |
Correction on RX spurious emissions of Band VI and XIX |
12.9.0 |
|
RP-69 |
RP-151483 |
1071 |
1 |
F |
UMTS UE co-existence requirements from the Japanese bands to the frequency range of 3400-3600 MHz |
12.9.0 |
|
RP-69 |
RP-151492 |
1073 |
A |
Correction to table C.24 title |
12.9.0 |
||
RP-69 |
RP-151477 |
1075 |
F |
Correction in the available channel list when DPCCH2 is configured |
12.9.0 |
||
RP-69 |
RP-151483 |
1076 |
F |
Correction of notes for UE additional TX/RX spurious emissions requirements |
12.9.0 |
||
RP-69 |
RP-151492 |
1074 |
B |
Introduction of the Multiflow 3F-4C configuration |
13.0.0 |
||
RP-70 |
RP-152171 |
1084 |
– |
B |
Introduction of Band 65 to TS 25.101 |
13.1.0 |
|
RP-70 |
RP-152157 |
1086 |
– |
B |
Introduction of Band 67 |
13.1.0 |
|
RP-70 |
RP-152172 |
1087 |
– |
B |
Introduction of Band 66 |
13.1.0 |
|
RP-70 |
RP-152140 |
1088 |
1 |
B |
25.101CR to introduce DB-DC-HSUPA |
13.1.0 |
|
RP-70 |
RP-152142 |
1089 |
1 |
B |
Out-of-synchronization requirement for UTRA TPC algorithm 3 |
13.1.0 |
|
RP-70 |
RP-152175 |
1090 |
– |
B |
Introduction of Region 3 requirement in Band 65 |
13.1.0 |
|
RP-70 |
RP-152144 |
1091 |
1 |
B |
Introduction of Dual Carrier HSUPA enhancements for UTRAN CS in TS 25.101 |
13.1.0 |
|
RP-70 |
RP-152173 |
1092 |
– |
B |
Introduction of 1447-1467MHz Band into 25.101 |
13.1.0 |
|
03/2016 |
RP-71 |
RP-160484 |
1093 |
1 |
B |
Introduction of TPC decoding requirement due to TPC algorithm 3 |
13.2.0 |
03/2016 |
RP-71 |
RP-160487 |
1099 |
1 |
A |
CR on ILPC Exceptions |
13.2.0 |
2016-05 |
Correction to RP-71 entries in change history table above |
13.2.1 |
|||||
2016/06 |
RP-72 |
RP-161125 |
1101 |
– |
B |
Introduction of Band 70 to 25.101 |
14.0.0 |
2017/09 |
RP-77 |
RP-171952 |
1102 |
B |
Introduction of Band 71 to TS25.101 |
15.0.0 |
|
2017/09 |
RP-77 |
RP-171948 |
1103 |
B |
Introduction of the FDD L-band (Band 74) into TS 25.101 |
15.0.0 |
|
2017/09 |
RP-77 |
RP-171946 |
1104 |
1 |
B |
Addition of band 72 protection TS 25.101 |
15.0.0 |
2017/09 |
RP-77 |
RP-171949 |
1105 |
1 |
B |
Introduction of L-band for SDL, TDD and FDD for TS 25.101 |
15.0.0 |
2017/09 |
RP-77 |
RP-171950 |
1106 |
B |
Protection of E-UTRA Extended 1.5 GHz SDL bands 75 and 76 |
15.0.0 |
|
2017/12 |
RP-78 |
RP-172593 |
1107 |
1 |
B |
Introduction of Band 73 into TS 25.101 |
15.1.0 |
2018-03 |
RAN#79 |
RP-180279 |
1109 |
B |
CR to 25.101: Introduction of Band 85 (B12-extended) |
15.2.0 |
|
2018-03 |
RAN#79 |
RP-180278 |
1110 |
B |
Introduction of TDD 3.3-3.4GHz band (band 52) |
15.2.0 |
|
2018-12 |
RAN#82 |
RP-182376 |
1112 |
1 |
B |
Introduction of band 53 into TS 25.101 |
16.0.0 |
2019-03 |
RAN#83 |
RP-190401 |
1115 |
A |
Introduction of NR protection in TS25.101 |
16.1.0 |
Change history |
|||||||
Date |
Meeting |
TDoc |
CR |
Rev |
Cat |
Subject/Comment |
New version |
2022-03 |
SA#95 |
Update to Rel-17 version (MCC) |
17.0.0 |