5 Frequency bands and channel arrangement
25.1013GPPRelease 17TSUser Equipment (UE) radio transmission and reception (FDD)
5.1 General
The information presented in this subclause is based on a chip rate of 3.84 Mcps.
NOTE: Other chip rates may be considered in future releases.
5.2 Frequency bands
a) UTRA/FDD is designed to operate in the following paired bands:
Table 5.0: UTRA FDD frequency bands
Operating Band |
UL Frequencies UE transmit, Node B receive |
DL frequencies UE receive, Node B transmit |
---|---|---|
I |
1920 – 1980 MHz |
2110 -2170 MHz |
II |
1850 -1910 MHz |
1930 -1990 MHz |
III |
1710-1785 MHz |
1805-1880 MHz |
IV |
1710-1755 MHz |
2110-2155 MHz |
V |
824 – 849 MHz |
869-894 MHz |
VI |
830-840 MHz |
875-885 MHz |
VII |
2500-2570 MHz |
2620-2690 MHz |
VIII |
880 – 915 MHz |
925 – 960 MHz |
IX |
1749.9-1784.9 MHz |
1844.9-1879.9 MHz |
X |
1710-1770 MHz |
2110-2170 MHz |
XI |
1427.9 – 1447.9 MHz |
1475.9 – 1495.9 MHz |
XII |
699 – 716 MHz |
729 – 746 MHz |
XIII |
777 – 787 MHz |
746 – 756 MHz |
XIV |
788 – 798 MHz |
758 – 768 MHz |
XV |
Reserved |
Reserved |
XVI |
Reserved |
Reserved |
XVII |
Reserved |
Reserved |
XVIII |
Reserved |
Reserved |
XIX |
830 – 845MHz |
875 – 890 MHz |
XX |
832 – 862 MHz |
791 – 821 MHz |
XXI |
1447.9 – 1462.9 MHz |
1495.9 – 1510.9 MHz |
XXII |
3410 – 3490 MHz |
3510 – 3590 MHz |
XXV |
1850 – 1915 MHz |
1930 – 1995 MHz |
XXVI |
814 – 849 MHz |
859 – 894 MHz |
XXXII1 |
N/A |
1452 – 1496 MHz |
NOTE 1: Restricted to UTRA operation when dual band is configured (e.g., DB-DC-HSDPA or dual band 4C-HSDPA). The down link frequenc(ies) of this band are paired with the uplink frequenc(ies) of the other FDD band (external) of the dual band configuration. |
b) Deployment in other frequency bands is not precluded
c) DB-DC-HSDPA is designed to operate in the following configurations:
Table 5.0aA DB-DC-HSDPA configurations
DB-DC-HSDPA Configuration |
UL Band |
DL Band A |
DL Band B |
---|---|---|---|
1 |
I or VIII |
I |
VIII |
2 |
II or IV |
II |
IV |
3 |
I or V |
I |
V |
4 |
I or XI |
I |
XI |
5 |
II or V |
II |
V |
6 |
I |
I |
XXXII |
d) Single band 4C-HSDPA is designed to operate in the following configurations:
Table 5.0aB Single band 4C-HSDPA configurations
Single band 4C-HSDPA Configuration |
Operating Band |
Number of DL carriers |
---|---|---|
I-3 |
I |
3 |
II-3 |
II |
3 |
II-4 |
II |
4 |
NOTE: Single band 4C-HSDPA configuration is numbered as (X-M) where X denotes the operating band and M denotes the number of DL carriers. |
e) Dual band 4C-HSDPA is designed to operate in the following configurations:
Table 5.0aC Dual band 4C-HSDPA configurations
Dual band 4C-HSDPA Configuration |
UL Band |
DL Band A |
Number of DL carriers in Band A |
DL Band B |
Number of DL carriers in Band B |
---|---|---|---|---|---|
I-2-VIII-1 |
I or VIII |
I |
2 |
VIII |
1 |
I-2-VIII-2 |
I or VIII |
I |
2 |
VIII |
2 |
I-1-VIII-2 |
I or VIII |
I |
1 |
VIII |
2 |
I-3-VIII-1 |
I or VIII |
I |
3 |
VIII |
1 |
II-1-IV-2 |
II or IV |
II |
1 |
IV |
2 |
II-2-IV-1 |
II or IV |
II |
2 |
IV |
1 |
II-2-IV-2 |
II or IV |
II |
2 |
IV |
2 |
I-1-V-2 |
I or V |
I |
1 |
V |
2 |
I-2-V-1 |
I or V |
I |
2 |
V |
1 |
I-2-V-2 |
I or V |
I |
2 |
V |
2 |
II-1-V-2 |
II or V |
II |
1 |
V |
2 |
I-1-XXXII-2 |
I |
I |
1 |
XXXII |
2 |
I-2-XXXII-1 |
I |
I |
2 |
XXXII |
1 |
NOTE: Dual band 4C-HSDPA configuration is numbered as (X-M-Y-N) where X denotes the DL Band A, M denotes the number DL carriers in the DL Band A, Y denotes the DL Band B, and N denotes the number of DL carriers in the DL Band B |
f) Single band 8C-HSDPA is designed to operate in the following configurations:
Table 5.0aD Single band 8C-HSDPA configurations
Single band 8C-HSDPA Configuration |
Operating Band |
Number of DL carriers |
---|---|---|
I-8 |
I |
8 |
NOTE: Single band 8C-HSDPA configuration is numbered as (X-M) where X denotes the operating band and M denotes the number of DL carriers. |
g) Single band NC-4C-HSDPA is designed to operate in the following configurations:
Table 5.0aE Single band NC-4C-HSDPA configurations
Single band NC-4C-HSDPA Configuration |
Operating Band |
Number of DL carriers in one subblock |
Gap between subblocks [MHz] |
Number of DL carriers in the other subblock |
---|---|---|---|---|
I-1-5-1 |
I |
1 |
5 |
1 |
I-2-5-1 |
I |
2 |
5 |
1 |
I-3-10-1 |
I |
3 |
10 |
1 |
IV-1-5-1 |
IV |
1 |
5 |
1 |
IV-2-10-1 |
IV |
2 |
10 |
1 |
IV-2-15-2 |
IV |
2 |
15 |
2 |
IV-2-20-1 |
IV |
2 |
20 |
1 |
IV-2-25-2 |
IV |
2 |
25 |
2 |
NOTE: Single band NC-4C-HSDPA configuration is numbered as (X-M-Y-N) where X denotes the operating band, M denotes the number of DL carriers in one subblock, Y denotes the gap between subblocks in MHz and N denotes the number of DL carriers in the other subblock. M and N can be switched |
h) DB-DC-HSUPA is designed to operate in the following configurations:
Table 5.0aF: Dual Band HSUPA Configurations
Dual band HSUPA Configuration together with DB-DC-HSDPA/DB-4C-HSDPA |
UL Band A/B |
Number of UL carriers in Band A/B |
DL Band A |
Number of DL carriers in Band A |
DL Band B |
Number of DL carriers in Band B |
---|---|---|---|---|---|---|
I-1-VIII-1 |
I and VIII |
1 |
I |
1 |
VIII |
1 |
I-2-VIII-1 |
I and VIII |
1 |
I |
2 |
VIII |
1 |
I-2-VIII-2 |
I and VIII |
1 |
I |
2 |
VIII |
2 |
I-1-VIII-2 |
I and VIII |
1 |
I |
1 |
VIII |
2 |
I-3-VIII-1 |
I and VIII |
1 |
I |
3 |
VIII |
1 |
I-1-V-1 |
I and V |
1 |
I |
1 |
V |
1 |
I-1-V-2 |
I and V |
1 |
I |
1 |
V |
2 |
I-2-V-1 |
I and V |
1 |
I |
2 |
V |
1 |
I-2-V-2 |
I and V |
1 |
I |
2 |
V |
2 |
II-1-V-1 |
II and V |
1 |
II |
1 |
V |
1 |
II-1-V-2 |
II and V |
1 |
II |
1 |
V |
2 |
5.3 TX-RX frequency separation
a) UTRA/FDD is designed to operate with the following TX-RX frequency separation
Table 5.0A: TX-RX frequency separation
Operating Band |
TX-RX frequency separation |
---|---|
I |
190 MHz |
II |
80 MHz. |
III |
95 MHz. |
IV |
400 MHz |
V |
45 MHz |
VI |
45 MHz |
VII |
120 MHz |
VIII |
45 MHz |
IX |
95 MHz |
X |
400 MHz |
XI |
48 MHz |
XII |
30 MHz |
XIII |
31 MHz |
XIV |
30 MHz |
XIX |
45 MHz |
XX |
41 MHz |
XXI |
48 MHz |
XXII |
100 MHz |
XXV |
80 MHz |
XXVI |
45MHz |
b) UTRA/FDD can support both fixed and variable transmit to receive frequency separation.
c) The use of other transmit to receive frequency separations in existing or other frequency bands shall not be precluded.
d) When configured to operate on dual cells in the DL with a single UL frequency, the TX-RX frequency separation in Table 5.0A shall be applied for the serving HS-DSCH cell. For bands XII, XIII and XIV, the TX-RX frequency separation in Table 5.0A shall be the minimum spacing between the UL and either of the DL carriers.
e) When configured to operate on dual cells in both the DL and UL, the TX-RX frequency separation in Table 5.0A shall be applied to the primary UL frequency and DL frequency of the serving HS-DSCH cell, and to the secondary UL frequency and the frequency of the secondary serving HS-DSCH cell respectively.
f) When configured to operate on single/dual band 4C-HSDPA or single band 8C-HSDPA or single band NC-4C-HSDPA with a single UL frequency, the TX-RX frequency separation in Table 5.0A shall be applied for the DL frequency of the serving HS-DSCH cell. When configured to operate on single/dual band 4C-HSDPA or single band 8C-HSDPA or single band NC-4C-HSDPA with dual UL frequencies, the TX-RX frequency separation in Table 5.0A shall be applied to the primary UL frequency and DL frequency of the serving HS-DSCH cell, and to the secondary UL frequency and the frequency of the 1st secondary serving HS-DSCH cell respectively.
g) For bands XII, XIII and XIV, all the requirements in TS 25.101 are applicable only for a single uplink carrier frequency, however dual cell uplink operation may be considered in future releases.
f) When configured to operate on dual band dual cell HSDPA or dual band 4C-HSDPA with dual band UL frequencies, the TX-RX frequency separation in Table 5.0A shall be applied to the primary UL frequency and DL frequency of the serving HS-DSCH cell, and to the secondary UL frequency and the frequency of the 1st secondary serving HS-DSCH cell respectively.
5.4 Channel arrangement
5.4.1 Channel spacing
The nominal channel spacing is 5 MHz, but this can be adjusted to optimise performance in a particular deployment scenario. In DC-HSDPA and DB-DC-HSDPA mode, the UE receives two cells simultaneously. In context of DC-HSDPA and DB-DC-HSDPA, a cell is characterized by a combination of scrambling code and a carrier frequency, see [21.905].
5.4.2 Channel raster
The channel raster is 200 kHz, for all bands which means that the centre frequency must be an integer multiple of 200 kHz. In addition a number of additional centre frequencies are specified according to table 5.1A, which means that the centre frequencies for these channels are shifted 100 kHz relative to the general raster.
5.4.3 Channel number
The carrier frequency is designated by the UTRA Absolute Radio Frequency Channel Number (UARFCN). For each operating Band, the UARFCN values are defined as follows:
Uplink: NU = 5 * (FUL – FUL_Offset), for the carrier frequency range FUL_low FUL FUL_high
Downlink: ND = 5 * (FDL – FDL_Offset), for the carrier frequency range FDL_low FDL FDL_high
For each operating Band, FUL_Offset, FUL_low FUL_high, FDL_Offset,, FDL_lowand FDL_high are defined in Table 5.1 for the general UARFCN. For the additional UARFCN, FUL_Offset, FDL_Offset and the specific FUL and FDL are defined in Table 5.1A.
Table 5.1: UARFCN definition (general)
Band |
UPLINK (UL) UE transmit, Node B receive |
DOWNLINK (DL) UE receive, Node B transmit |
||||
---|---|---|---|---|---|---|
UARFCN formula offset FUL_Offset [MHz] |
Carrier frequency (FUL) range [MHz] |
UARFCN formula offset FDL_Offset [MHz] |
Carrier frequency (FDL) range [MHz] |
|||
FUL_low |
FUL_high |
FDL_low |
FDL_high |
|||
I |
0 |
1922.4 |
1977.6 |
0 |
2112.4 |
2167.6 |
II |
0 |
1852.4 |
1907.6 |
0 |
1932.4 |
1987.6 |
III |
1525 |
1712.4 |
1782.6 |
1575 |
1807.4 |
1877.6 |
IV |
1450 |
1712.4 |
1752.6 |
1805 |
2112.4 |
2152.6 |
V |
0 |
826.4 |
846.6 |
0 |
871.4 |
891.6 |
VI |
0 |
832.4 |
837.6 |
0 |
877.4 |
882.6 |
VII |
2100 |
2502.4 |
2567.6 |
2175 |
2622.4 |
2687.6 |
VIII |
340 |
882.4 |
912.6 |
340 |
927.4 |
957.6 |
IX |
0 |
1752.4 |
1782.4 |
0 |
1847.4 |
1877.4 |
X |
1135 |
1712.4 |
1767.6 |
1490 |
2112.4 |
2167.6 |
XI |
733 |
1430.4 |
1445.4 |
736 |
1478.4 |
1493.4 |
XII |
-22 |
701.4 |
713.6 |
-37 |
731.4 |
743.6 |
XIII |
21 |
779.4 |
784.6 |
-55 |
748.4 |
753.6 |
XIV |
12 |
790.4 |
795.6 |
-63 |
760.4 |
765.6 |
XIX |
770 |
832.4 |
842.6 |
735 |
877.4 |
887.6 |
XX |
-23 |
834.4 |
859.6 |
-109 |
793.4 |
818.6 |
XXI |
1358 |
1450.4 |
1460.4 |
1326 |
1498.4 |
1508.4 |
XXII |
2525 |
3412.4 |
3487.6 |
2580 |
3512.4 |
3587.6 |
XXV |
875 |
1852.4 |
1912.6 |
910 |
1932.4 |
1992.6 |
XXVI |
-291 |
816.4 |
846.6 |
-291 |
861.4 |
891.6 |
XXXII1 |
N/A |
131 |
1454.4 |
1493.6 |
||
NOTE 1: Restricted to UTRA operation when dual band is configured (e.g., DB-DC-HSDPA or dual band 4C-HSDPA) |
Table 5.1A: UARFCN definition (additional channels)
Band |
UPLINK (UL) UE transmit, Node B receive |
DOWNLINK (DL) UE receive, Node B transmit |
||
---|---|---|---|---|
UARFCN formula offset FUL_Offset [MHz] |
Carrier frequency [MHz] (FUL) |
UARFCN formula offset FDL_Offset [MHz] |
Carrier frequency [MHz] (FDL) |
|
I |
– |
– |
– |
– |
II |
1850.1 |
1852.5, 1857.5, 1862.5, 1867.5, 1872.5, 1877.5, 1882.5, 1887.5, 1892.5, 1897.5, 1902.5, 1907.5 |
1850.1 |
1932.5, 1937.5, 1942.5, 1947.5, 1952.5, 1957.5, 1962.5, 1967.5, 1972.5, 1977.5, 1982.5, 1987.5 |
III |
– |
– |
– |
– |
IV |
1380.1 |
1712.5, 1717.5, 1722.5, 1727.5, 1732.5, 1737.5 1742.5, 1747.5, 1752.5 |
1735.1 |
2112.5, 2117.5, 2122.5, 2127.5, 2132.5, 2137.5, 2142.5, 2147.5, 2152.5 |
V |
670.1 |
826.5, 827.5, 831.5, 832.5, 837.5, 842.5 |
670.1 |
871.5, 872.5, 876.5, 877.5, 882.5, 887.5 |
VI |
670.1 |
832.5, 837.5 |
670.1 |
877.5, 882.5 |
VII |
2030.1 |
2502.5, 2507.5, 2512.5, 2517.5, 2522.5, 2527.5, 2532.5, 2537.5, 2542.5, 2547.5, 2552.5, 2557.5, 2562.5, 2567.5 |
2105.1 |
2622.5, 2627.5, 2632.5, 2637.5, 2642.5, 2647.5, 2652.5, 2657.5, 2662.5, 2667.5, 2672.5, 2677.5, 2682.5, 2687.5 |
VIII |
– |
– |
– |
– |
IX |
– |
– |
– |
– |
X |
1075.1 |
1712.5, 1717.5, 1722.5, 1727.5, 1732.5, 1737.5, 1742.5, 1747.5, 1752.5, 1757.5, 1762.5, 1767.5 |
1430.1 |
2112.5, 2117.5, 2122.5, 2127.5, 2132.5, 2137.5, 2142.5, 2147.5, 2152.5, 2157.5, 2162.5, 2167.5 |
XI |
– |
– |
– |
– |
XII |
–39.9 |
701.5, 706.5, 707.5, 712.5, 713.5 |
–54.9 |
731.5, 736.5, 737.5, 742.5, 743.5 |
XIII |
11.1 |
779.5, 784.5 |
-64.9 |
748.5, 753.5 |
XIV |
2.1 |
790.5, 795.5 |
-72.9 |
760.5, 765.5 |
XIX |
755.1 |
832.5, 837.5, 842.5 |
720.1 |
877.5, 882.5, 887.5 |
XX |
– |
– |
– |
– |
XXI |
– |
– |
– |
– |
XXII |
– |
– |
– |
– |
XXV |
639.1 |
1852.5, 1857.5, 1862.5,1867.5, 1872.5, 1877.5, 1882.5, 1887.5, 1892.5, 1897.5, 1902.5, 1907.5, 1912.5 |
674.1 |
1932.5, 1937.5, 1942.5, 1947.5, 1952.5, 1957.5, 1962.5, 1967.5, 1972.5, 1977.5, 1982.5, 1987.5, 1992.5 |
XXVI |
-325.9 |
816.5, 821.5, 826.5, 827.5, 831.5, 832.5, 836.5, 837.5, 841.5, 842.5, 846.5 |
-325.9 |
861.5, 866.5, 871.5, 872.5, 876.5, 877.5, 881.5, 882.5, 886,5, 887.5, 891.5 |
XXXII1 |
N/A |
87.1 |
1454.5, 1459.5, 1464.5, 1469.5, 1474.5, 1479.5, 1484.5, 1489.5 |
|
NOTE 1: Restricted to UTRA operation when dual band is configured (e.g., DB-DC-HSDPA or dual band 4C-HSDPA) |
5.4.4 UARFCN
The following UARFCN range shall be supported for each paired band
Table 5.2: UTRA Absolute Radio Frequency Channel Number
Band |
Uplink (UL) UE transmit, Node B receive |
Downlink (DL) UE receive, Node B transmit |
|||||||
---|---|---|---|---|---|---|---|---|---|
General |
Additional |
General |
Additional |
||||||
I |
9612 to 9888 |
– |
10562 to 10838 |
– |
|||||
II |
9262 to 9538 |
12, 37, 62, 87, 112, 137, 162, 187, 212, 237, 262, 287 |
9662 to 9938 |
412, 437, 462, 487, 512, 537, 562, 587, 612, 637, 662, 687 |
|||||
III |
937 to 1288 |
– |
1162 to 1513 |
– |
|||||
IV |
1312 to 1513 |
1662, 1687, 1712, 1737, 1762, 1787, 1812, 1837, 1862 |
1537 to 1738 |
1887, 1912, 1937, 1962, 1987, 2012, 2037, 2062, 2087 |
|||||
V |
4132 to 4233 |
782, 787, 807, 812, 837, 862 |
4357 to 4458 |
1007, 1012, 1032, 1037, 1062, 1087 |
|||||
VI |
4162 to 4188 |
812, 837 |
4387 to 4413 |
1037, 1062 |
|||||
VII |
2012 to 2338 |
2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687 |
2237 to 2563 |
2587, 2612, 2637, 2662, 2687, 2712, 2737, 2762, 2787, 2812, 2837, 2862, 2887, 2912 |
|||||
VIII |
2712 to 2863 |
– |
2937 to 3088 |
– |
|||||
IX |
8762 to 8912 |
– |
9237 to 9387 |
– |
|||||
X |
2887 to 3163 |
3187, 3212, 3237, 3262, 3287, 3312, 3337, 3362, 3387, 3412, 3437, 3462 |
3112 to 3388 |
3412, 3437, 3462, 3487, 3512, 3537, 3562, 3587, 3612, 3637, 3662, 3687 |
|||||
XI |
3487 to 3562 |
– |
3712 to 3787 |
– |
|||||
XII |
3617 to 3678 |
3707, 3732, 3737, 3762, 3767 |
3842 to 3903 |
3932, 3957, 3962, 3987, 3992 |
|||||
XIII |
3792 to 3818 |
3842, 3867 |
4017 to 4043 |
4067, 4092 |
|||||
XIV |
3892 to 3918 |
3942, 3967 |
4117 to 4143 |
4167, 4192 |
|||||
XIX |
312 to 363 |
387, 412, 437 |
712 to 763 |
787, 812, 837 |
|||||
XX |
4287 to 4413 |
– |
4512 to 4638 |
– |
|||||
XXI |
462 to 512 |
– |
862 to 912 |
– |
|||||
XXII |
4437 to 4813 |
– |
4662 to 5038 |
– |
|||||
XXV |
4887 to 5188 |
6067, 6092, 6117, 6142, 6167, 6192, 6217, 6242, 6267, 6292, 6317, 6342, 6367 |
5112 to 5413 |
6292, 6317, 6342, 6367, 6392, 6417, 6442, 6467, 6492, 6517, 6542, 6567, 6592 |
|||||
XXVI |
5537 to 5688 |
5712, 5737, 5762, 5767, 5787, 5792, 5812, 5817, 5837, 5842, 5862 |
5762 to 5913 |
5937, 5962, 5987, 5992, 6012, 6017, 6037, 6042, 6062, 6067, 6087 |
|||||
XXXII1 |
N/A |
6617 to 6813 |
6837, 6862, 6887, 6912, 6937, 6962, 6987, 7012 |
||||||
NOTE 1: Restricted to UTRA operation when dual band is configured (e.g., DB-DC-HSDPA or dual band 4C-HSDPA) |
NOTE: If the UE is on a network with Mobile Country Code set to Japan then it may assume that any DL UARFCN sent by the network from the overlapping region of Band V and Band VI is from Band VI. If the UE is on a network with a Mobile Country Code other than Japan then it may assume that any DL UARFCN sent by the network from the overlapping region of Band V and Band VI is from Band V.