9.4 HS-SCCH Detection Performance

25.1013GPPRelease 17TSUser Equipment (UE) radio transmission and reception (FDD)

Tools: ARFCN - Frequency Conversion for 5G NR/LTE/UMTS/GSM

The detection performance of the HS-SCCH is determined by the probability of event E_m, which is declared when the UE is signaled on HS-SCCH-1, but DTX is observed in the corresponding HS-DPCCH ACK/NACK field. The probability of event E_m is denoted P(E_m).

9.4.1 HS-SCCH Type 1 Single Link Performance

For the test parameters specified in Table 9.50, for each value of HS-SCCH-1 E_c/I_or specified in Table 9.51 and Table 9.51A the measured P(E_m) shall be less than or equal to the corresponding specified value of P(E_m). Enhanced performance requirements type 1 specified in Table 9.51A are based on receiver diversity.

Table 9.50: Test parameters for HS-SCCH detection – single link

Parameter	Unit	Test 1	Test 2	Test 3
		dBm/3.84 MHz	-60
Phase reference		–	P-CPICH
P-CPICH		dB	-10
HS-SCCH UE Identity (,, …, )			HS-SCCH-1: 1010101010101010 (every third TTI only , UE under test addressed solely via HS-SCCH-1) HS-SCCH-2: 0001001010101010 HS-SCCH-3: 0001101010101010 HS-SCCH-4: 0001111110101010
HS-DSCH TF of UE1			TF corresponding to CQI1
HS-SCCH-1 transmission pattern			The HS-SCCH-1 shall be transmitted continuously with constant power.
HS-PDSCH transmission pattern			The HS-PDSCH shall be transmitted continuously with constant power.
HS-SCCH-1 TTI Signalling Pattern		–	The six sub-frame HS-SCCH-1 signalling pattern shall be “…XOOXOO…”, where “X” indicates TTI in which the HS-SCCH-1 uses the identity of the UE under test, and “O” indicates TTI in which the HS-SCCH-1 uses a different UE identity.

Table 9.51: Minimum requirement for HS-SCCH detection – single link

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-9	0	0.05
2	PA3	-9.9	5	0.01
3	VA30	-10	0	0.01

Table 9.51A: Enhanced requirement type 1 for HS-SCCH detection – single link

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-12.0	0	0.01
2	VA30	-15.6	0	0.01

9.4.2 HS-SCCH Type 1 Open Loop Diversity Performance

For the test parameters specified in Table 9.52, for each value of HS-SCCH-1 E_c/I_or specified in Table 9.53 and Table 9.54 the measured P(E_m) shall be less than or equal to the corresponding specified value of P(E_m). Enhanced performance requirements type 1 specified in Table 9.54 are based on receiver diversity.

Table 9.52: Test parameters for HS-SCCH detection – open loop diversity

Parameter	Unit	Test 1	Test 2	Test 3
		dBm/3.84 MHz	-60
Phase reference		–	P-CPICH
P-CPICH		dB	-10
HS-SCCH UE Identity (,, …, )			HS-SCCH-1: 1010101010101010 (every third TTI only,UE under test addressed solely via HS-SCCH-1) HS-SCCH-2: 0001001010101010 HS-SCCH-3: 0001101010101010 HS-SCCH-4: 0001111110101010
HS-DSCH TF of UE1			TF corresponding to CQI1
HS-SCCH-1 transmission pattern			The HS-SCCH-1 shall be transmitted continuously with constant power.
HS-PDSCH transmission pattern			The HS-PDSCH shall be transmitted continuously with constant power.
HS-SCCH-1 TTI Signalling Pattern		–	The six sub-frame HS-SCCH-1 signalling pattern shall be “…XOOXOO…”, where “X” indicates TTI in which the HS-SCCH-1 uses the identity of the UE under test, and “O” indicates TTI in which the HS-SCCH-1 uses a different UE identity.

Table 9.53: Minimum requirement for HS-SCCH detection – open loop diversity

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-11.6	0	0.05
2	PA3	-13.4	5	0.01
3	VA30	-11.5	0	0.01

Table 9.54: Enhanced requirement type 1 for HS-SCCH detection – open loop diversity

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-15.2	0	0.01
2	VA30	-16.4	0	0.01

9.4.3 HS-SCCH Type 3 Performance

For the test parameters specified in Table 9.55 with the downlink physical channel setup in Table C.12, for each value of HS-SCCH-1 E_c/I_or specified in Table 9.56 and Table 9.57 the measured P(E_m) shall be less than or equal to the corresponding specified value of P(E_m). The requirements in Table 9.56 and Table 9.57 assume STTD is enabled on HS-SCCH and DPCH. The requirements in Table 9.56 assume HS-SCCH Type 3 coding associated with single stream transmission on HS-DSCH. The requirements in Table 9.57 assume HS-SCCH Type 3 coding associated with dual stream transmission on HS-DSCH.

For the test parameters specified in Table 9.55 with the downlink physical channel setup in Table C.12E, for each value of HS-SCCH-1 E_c/I_or specified in Table 9.57a, Table 9.57b, Table 9.57c and Table 9.57d, the measured P(E_m) shall be less than or equal to the corresponding specified value of P(E_m). The requirements in Table 9.57a and Table 9.57b assume STTD is disabled on HS-SCCH and DPCH. The requirements in Table 9.57c and Table 9.57d assume STTD is enabled on HS-SCCH and DPCH. The requirements in Table 9.57a and Table 9.57c assume HS-SCCH Type 3 coding associated with single stream transmission on HS-DSCH. The requirements in Table 9.57b and Table 9.57d assume HS-SCCH Type 3 coding associated with dual stream transmission on HS-DSCH.

Minimum performance requirements specified in Table 9.56, 9.57, 9.57a, 9.57b, 9.57c and 9.57d are based on receiver diversity.

Table 9.55: Test parameters for HS-SCCH Type 3 detection

Parameter	Unit	Test 1	Test 2	Test 3	Test 4
			dBm/3.84 MHz	-60
HS-SCCH UE Identity (,, …, )				HS-SCCH-1: 1010101010101010 (every third TTI only,UE under test addressed solely via HS-SCCH-1) HS-SCCH-2: 0001001010101010 HS-SCCH-3: 0001101010101010 HS-SCCH-4: 0001111110101010
HS-DSCH TF of UE1				In case one transport block is signalled on HS-SCCH: One transport block with TF corresponding to CQI1 Precoding vector applied to HS-PDSCH shall cycle through the four possible options. In case two transport blocks are signalled on HS-SCCH: Two transport blocks with the same size and same number of OVSF codes as used in the case of transmitting only one transport block. Precoding matrix applied to HS-PDSCH shall cycle through the four possible options.
HS-SCCH-1 transmission pattern				The HS-SCCH-1 shall be transmitted continuously with constant power.
HS-PDSCH transmission pattern				The HS-PDSCH shall be transmitted continuously with constant power.
HS-SCCH-1 TTI Signalling Pattern			–	The six sub-frame HS-SCCH-1 signalling pattern shall be “…XOOXOO…”, where “X” indicates TTI in which the HS-SCCH-1 uses the identity of the UE under test, and “O” indicates TTI in which the HS-SCCH-1 uses a different UE identity.

Table 9.56: Minimum requirement for HS-SCCH Type 3 detection, single transport block case with downlink physical channel setup in Table C.12

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-15.6	0	0.01
2	VA3	-16.8	0	0.01

Table 9.57: Minimum requirement for HS-SCCH Type 3 detection, dual transport block case with downlink physical channel setup in Table C.12

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
3	PA3	-14.7	0	0.01
4	VA3	-16.0	0	0.01

Table 9.57a: Minimum requirement for HS-SCCH Type 3 detection, STTD disabled, single transport block case with downlink physical channel setup in Table C.12E

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-12.3	0	0.01
2	VA3	-14.9	0	0.01

Table 9.57b: Minimum requirement for HS-SCCH Type 3 detection, STTD disabled, dual transport block case with downlink physical channel setup in Table C.12E

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
3	PA3	-11.4	0	0.01
4	VA3	-14.2	0	0.01

Table 9.57c: Minimum requirement for HS-SCCH Type 3 detection, STTD enabled, single transport block case with downlink physical channel setup in Table C.12E

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-15.3	0	0.01
2	VA3	-16.7	0	0.01

Table 9.57d: Minimum requirement for HS-SCCH Type 3 detection, STTD enabled, dual transport block case with downlink physical channel setup in Table C.12E

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
3	PA3	-14.4	0	0.01
4	VA3	-15.8	0	0.01

9.4.4 HS-SCCH Type 3 Performance for MIMO only with single-stream restriction

For the test parameters specified in Table 9.57A1 with the downlink physical channel setup in Table C.12, for each value of HS-SCCH-1 E_c/I_or specified in Table 9.57A2 and Table 9.57A3 the measured P(E_m) shall be less than or equal to the corresponding specified value of P(E_m). The requirements in Table 9.57A2 and Table 9.57A3 assume STTD is enabled on HS-SCCH and DPCH. The requirements in Table 9.57A2 and Table 9.57A3 assume HS-SCCH Type 3 coding associated with single stream transmission on HS-DSCH. Performance requirements specified in Table 9.57A3 are based on receiver diversity.

For the test parameters specified in Table 9.57A1 with the downlink physical channel setup in Table C.12E, for each value of HS-SCCH-1 E_c/I_or specified in Table 9.57A4, Table 9.57A5, Table 9.57A6 and Table 9.57A7, the measured P(E_m) shall be less than or equal to the corresponding specified value of P(E_m). The requirements in Table 9.57A4 and Table 9.57A5 assume STTD is disabled on HS-SCCH and DPCH. The requirements in Table 9.57A6 and Table 9.57A7 assume STTD is enabled on HS-SCCH and DPCH. The requirements in Table 9.57A4, Table 9.57A5, Table 9.57A6 and Table 9.57A7 assume HS-SCCH Type 3 coding associated with single stream transmission on HS-DSCH. Performance requirements specified in Table 9.57A5 and Table 9.57A7 are based on receiver diversity.

Table 9.57A1: Test parameters for HS-SCCH Type 3 detection

Parameter	Unit	Test 1	Test 2
		dBm/3.84 MHz	-60
Phase reference		–	P-CPICH
P-CPICH		dB	-10
HS-SCCH UE Identity (,, …, )			HS-SCCH-1: 1010101010101010 (every third TTI only,UE under test addressed solely via HS-SCCH-1) HS-SCCH-2: 0001001010101010 HS-SCCH-3: 0001101010101010 HS-SCCH-4: 0001111110101010
HS-DSCH TF of UE1			One transport block with TF corresponding to CQI1 Precoding vector applied to HS-PDSCH shall cycle through the four possible options.
HS-SCCH-1 transmission pattern			The HS-SCCH-1 shall be transmitted continuously with constant power.
HS-PDSCH transmission pattern			The HS-PDSCH shall be transmitted continuously with constant power.
HS-SCCH-1 TTI Signalling Pattern		–	The six sub-frame HS-SCCH-1 signalling pattern shall be “…XOOXOO…”, where “X” indicates TTI in which the HS-SCCH-1 uses the identity of the UE under test, and “O” indicates TTI in which the HS-SCCH-1 uses a different UE identity.

Table 9.57A2: Minimum requirement for HS-SCCH Type 3 detection, single transport block case with downlink physical channel setup in Table C.12

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-8.9	0	0.01
2	VA3	-11.0	0	0.01

Table 9.57A3: Enhanced requirement type 1 for HS-SCCH Type 3 detection, single transport block case with downlink physical channel setup in Table C.12

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-15.6	0	0.01
2	VA3	-16.8	0	0.01

Table 9.57A4: Minimum requirement for HS-SCCH Type 3 detection, STTD disabled, single transport block case with downlink physical channel setup in Table C.12E

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-11.0	3	0.05
2	VA3	-8.7	0	0.01

Table 9.57A5: Enhanced requirement type 1 for HS-SCCH Type 3 detection, STTD disabled, single transport block case with downlink physical channel setup in Table C.12E

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-12.3	0	0.01
2	VA3	-14.9	0	0.01

Table 9.57A6: Minimum requirement for HS-SCCH Type 3 detection, STTD enabled, single transport block case with downlink physical channel setup in Table C.12E

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-8.4	0	0.01
2	VA3	-11.1	0	0.01

Table 9.57A7: Enhanced requirement type 1 for HS-SCCH Type 3 detection, STTD enabled, single transport block case with downlink physical channel setup in Table C.12E

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-15.3	0	0.01
2	VA3	-16.7	0	0.01

9.4.5 HS-SCCH Type 4 Performance

For the test parameters specified in Table 9.57B1 with the downlink physical channel setup in Table C.12G, for each value of HS-SCCH-1 E_c/I_or specified in Table 9.57B2 and Table 9.57B3 the measured P(E_m) shall be less than or equal to the corresponding specified value of P(E_m). The requirements in Table 9.57B2 and Table 9.57B3 assume STTD is disabled on HS-SCCH and DPCH. The requirements in Table 9.57B2 assume HS-SCCH Type 4 coding associated with single stream transmission on HS-DSCH. The requirements in Table 9.57B3 assume HS-SCCH Type 4 coding associated with four stream transmission on HS-DSCH.

Minimum performance requirements specified in Table 9.57B1, 9.57B2 are based on receiver diversity.

Table 9.57B1: Test parameters for HS-SCCH Type 4 detection

Parameter	Unit	Test 1	Test 2	Test 3	Test 4
	dBm/3.84 MHz	-60
HS-SCCH UE Identity (,, …, )		HS-SCCH-1: 1010101010101010 (every third TTI only,UE under test addressed solely via HS-SCCH-1) HS-SCCH-2: 0001001010101010 HS-SCCH-3: 0001101010101010 HS-SCCH-4: 0001111110101010
HS-DSCH TF of UE1		In case one transport block is signalled on HS-SCCH: One transport block with TF corresponding to CQI1 Precoding vector applied to HS-PDSCH shall cycle through all the possible options. In case four transport blocks are signalled on HS-SCCH: Three/four transport blocks with the same size and same number of OVSF codes as used in the case of transmitting only one transport block. Precoding matrix applied to HS-PDSCH shall cycle through all the possible options. Note that 2, 3 or 4 transport blocks will have the same HS-SCCH structure.
HS-SCCH-1 transmission pattern		The HS-SCCH-1 shall be transmitted continuously with constant power.
HS-PDSCH transmission pattern		The HS-PDSCH shall be transmitted continuously with constant power.
HS-SCCH-1 TTI Signalling Pattern	–	The six sub-frame HS-SCCH-1 signalling pattern shall be “…XOOXOO…”, where “X” indicates TTI in which the HS-SCCH-1 uses the identity of the UE under test, and “O” indicates TTI in which the HS-SCCH-1 uses a different UE identity.

Table 9.57B2: Minimum requirement for HS-SCCH Type 4 detection, single transport block case with downlink physical channel setup in Table C.12G

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-18	0	0.01
2	VA3	-19	0	0.01

Table 9.57B3: Minimum requirement for HS-SCCH Type 4 detection, four transport block case with downlink physical channel setup in Table C.12G

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
3	PA3	-21	5	0.01
4	VA3	-20	5	0.01

9.4.6 HS-SCCH Type 4 Performance for MIMO mode with Four Transmit Antennas Only with Dual-stream Restriction

For the test parameters specified in Table 9.57B4 with the downlink physical channel setup in Table C.12G, for each value of HS-SCCH-1 E_c/I_or specified in Table 9.57B5 and Table 9.57B6 the measured P(E_m) shall be less than or equal to the corresponding specified value of P(E_m). The requirements in Table 9.57B5 and Table 9.57B6 assume STTD is disabled on HS-SCCH and DPCH. The requirements in Table 9.57B5 and Table 9.57B6 assume HS-SCCH Type 4 coding associated with dual stream transmission on HS-DSCH. Performance requirements specified in Table 9.57B5 and 9.57B6 are based on (dual branches) receiver diversity.

Table 9.57B4: Test parameters for HS-SCCH Type 4 detection

Parameter	Unit		Test 1	Test 2	Test 3	Test 4
	dBm/3.84 MHz	-60
HS-SCCH UE Identity (,, …, )		HS-SCCH-1: 1010101010101010 (every third TTI only,UE under test addressed solely via HS-SCCH-1) HS-SCCH-2: 0001001010101010 HS-SCCH-3: 0001101010101010 HS-SCCH-4: 0001111110101010
HS-DSCH TF of UE1		In case one transport block is signalled on HS-SCCH: One transport block with TF corresponding to CQI1 Precoding vector applied to HS-PDSCH shall cycle through all the possible options. Two transport blocks are signalled on HS-SCCH: Two transport blocks with the same size and same number of OVSF codes as used in the case of transmitting only one transport block. Precoding matrix applied to HS-PDSCH shall cycle through all the possible options.
HS-SCCH-1 transmission pattern		The HS-SCCH-1 shall be transmitted continuously with constant power.
HS-PDSCH transmission pattern		The HS-PDSCH shall be transmitted continuously with constant power.
HS-SCCH-1 TTI Signalling Pattern	–	The six sub-frame HS-SCCH-1 signalling pattern shall be “…XOOXOO…”, where “X” indicates TTI in which the HS-SCCH-1 uses the identity of the UE under test, and “O” indicates TTI in which the HS-SCCH-1 uses a different UE identity.

Table 9.57B5: Enhanced requirement type 1 for HS-SCCH Type 4 detection, single transport block case with downlink physical channel setup in Table C.12G

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-17	5	0.01
2	VA3	-17.8	5	0.01

Table 9.57B6: Enhanced requirement type 1 for HS-SCCH Type 4 detection, dual transport block case with downlink physical channel setup in Table C.12G

Test Number	Propagation Conditions	Reference value
Test Number	Propagation Conditions	HS-SCCH-1 (dB)	(dB)
1	PA3	-19	10	0.01
2	VA3	-18.5	10	0.01