7.6.3E Additional requirement for single band NC-4C-HSDPA (Narrow band blocking)
25.1013GPPRelease 17TSUser Equipment (UE) radio transmission and reception (FDD)
This requirement is measure of a receiver’s ability to receive a W-CDMA signal at its assigned channel frequency in the presence of an unwanted narrow band interferer at a frequency, which is less than the nominal channel spacing.
7.6.3E.1 Single uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.7I and Table 7.7J.
Table 7.7I: Test parameters for narrow band blocking characteristics, single band NC-4C-HSDPA, single uplink operation
Parameter |
Unit |
Band IV |
|
Iblocking (GMSK) |
dBm |
-57 |
|
Fuw (offset) (NOTE 2, 3) |
MHz |
±2.7 |
|
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
|
NOTE 1: Iblocking (GMSK) is an interfering signal as defined in TS 45.004 [6]. NOTE 2: For single band NC-4C-HSPDA out-of-gap, negative offset refers to the assigned channel frequency of the lowest carrier belonging to the lower subblock of carriers, and positive offset refers to the assigned channel frequency of the highest carrier belonging to the higher subblock of carriers. NOTE 3: For single band NC-4C-HSPDA in-gap, negative offset refers to the assigned channel frequency of the lowest carrier belonging to the higher subblock of carriers, and positive offset refers to the assigned channel frequency of the highest carrier belonging to the lower subblock of carriers. |
Table 7.7J: Narrow band blocking requirements, single band NC-4C-HSDPA, single uplink operation
Single band NC-4C-HSDPA Configuration |
Test type |
DL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UL-DL carrier separation |
|
IV-1-5-1, IV-2-10-1, IV-2-15-2, IV-2-20-1, IV-2-25-2 |
In-gap |
IV |
<REFSENS>+10 dB |
<REFÎor>+10 dB |
Minimum |
|
IV-1-5-1, IV-2-10-1, IV-2-15-2, IV-2-20-1, IV-2-25-2 |
Out-of-gap |
IV |
<REFSENS>+10 dB |
<REFÎor>+10 dB |
Minimum |
|
NOTE: <REFSENS> and <REFÎor> refer to the HS-PDSCH_Ec<REFSENS> and the HS-PDSCH<REFÎor> as specified in Table 7.2E for single band NC-4C-HSDPA. |
7.6.3E.2 Dual uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.7K and Table 7.7L.
Table 7.7KTest parameters for narrow band blocking characteristics for single band NC-4C-HSDPA, dual uplink operation
Parameter |
Unit |
Band IV |
|
Iblocking (GMSK) |
dBm |
-57 |
|
Fuw (offset) (NOTE 2, 3) |
MHz |
±2.7 |
|
NOTE 1: Iblocking (GMSK) is an interfering signal as defined in TS 45.004 [6]. NOTE 2: For single band NC-4C-HSPDA out-of-gap, negative offset refers to the assigned channel frequency of the lowest carrier belonging to the lower subblock of carriers, and positive offset refers to the assigned channel frequency of the highest carrier belonging to the higher subblock of carriers. NOTE 3: For single band NC-4C-HSPDA in-gap, negative offset refers to the assigned channel frequency of the lowest carrier belonging to the higher subblock of carriers, and positive offset refers to the assigned channel frequency of the highest carrier belonging to the lower subblock of carriers. |
Table 7.7L: Narrow band blocking requirements, single band NC-4C-HSDPA, dual uplink operation
Single band NC-4C-HSDPA Configuration |
Test type |
DL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UE transmitted mean power (dBm) |
UL-DL carrier separation |
IV-2-10-1, IV-2-15-2, IV-2-20-1, IV-2-25-2 |
In-gap |
IV |
-102.8 |
-92.5 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
IV-2-10-1, IV-2-15-2, IV-2-20-1, IV-2-25-2 |
Out-of-gap |
IV |
-102.8 |
-92.5 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
NOTE 1 For the UE which supports DB-DC-HSDPA configuration in Table 5.0aA the < HS-PDSCH_Ec > and < Îor > are allowed to be increased by an amount defined in Table 7.12. NOTE 2 For the UE which supports dual band 4C-HSDPA configuration in Table 5.0aC the < HS-PDSCH_Ec > and < Îor > are allowed to be increased by an amount defined in Table 7.13. |