7.8 Intermodulation characteristics
25.1013GPPRelease 17TSUser Equipment (UE) radio transmission and reception (FDD)
Third and higher order mixing of the two interfering RF signals can produce an interfering signal in the band of the desired channel. Intermodulation response rejection is a measure of the capability of the receiver to receiver a wanted signal on its assigned channel frequency in the presence of two or more interfering signals which have a specific frequency relationship to the wanted signal.
7.8.1 Minimum requirement
The BER shall not exceed 0.001 for the parameters specified in Table 7.9.
Table 7.9: Receive intermodulation characteristics
Parameter |
Unit |
Level |
|
DPCH_Ec |
dBm/3.84 MHz |
<REFSENS> +3 dB |
|
Îor |
dBm/3.84 MHz |
<REFÎor> +3 dB |
|
Iouw1 (CW) |
dBm |
-46 |
|
Iouw2 mean power (modulated) |
dBm |
-46 |
|
Fuw1 (offset) |
MHz |
10 |
-10 |
Fuw2 (offset) |
MHz |
20 |
-20 |
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) N OTE 3 |
|
NOTE 1: Iouw2 (modulated) consists of the common channels needed for tests as specified in Table C.7 and 16 dedicated data channels as specified in Table C.6. NOTE 2: <REFSENS> and <REFÎor> refer to the DPCH_Ec<REFSENS> and the DPCH<REFÎor> as specified in Table 7.2. NOTE 3 :The UE transmitted mean power shall be reduced by 0.5dB for a UE operating in band XXII. |
7.8.1A Additional requirement for DC-HSDPA and DB-DC-HSDPA
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9AA.
Table 7.9AA: Receive intermodulation characteristics
Parameter |
Unit |
Level |
|
HS-PDSCH_Ec |
dBm/3.84 MHz |
<REFSENS> +3 dB |
|
Îor |
dBm/3.84 MHz |
<REFÎor> +3 dB |
|
Iouw1 (CW) |
dBm |
-46 |
|
Iouw2 mean power (modulated) |
dBm |
-46 |
|
Fuw1 (offset) (NOTE 2) |
MHz |
10 |
-10 |
Fuw2 (offset) (NOTE 2) |
MHz |
20 |
-20 |
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) N OTE 4 |
|
NOTE 1: Iouw2 (modulated) consists of the common channels needed for tests as specified in Table C.7 and 16 dedicated data channels as specified in Table C.6. NOTE 2: For DC-HSDPA, negative offset refers to the assigned channel frequency of the lowest carrier frequency used and positive offset refers to the assigned channel frequency of the highest carrier frequency used. For DB-DC-HSDPA, offset refers to the assigned channel frequencies of the individual cells. NOTE 3: <REFSENS> and <REFÎor> refers to the HS-PDSCH_Ec<REFSENS> and the HS-PDSCH<REFÎor> as specified in Table 7.2A for DC-HSDPA and Table 7.2B for DB-DC-HSDPA. NOTE 4 :The UE transmitted mean power shall be reduced by 0.5dB for a UE operating in band XXII. |
7.8.1B Additional requirement for DC-HSUPA
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9AB and Table 7.9AC.
Table 7.9AB: Receive intermodulation characteristics
Parameter |
Unit |
Level |
|
Iouw1 (CW) |
dBm |
-46 |
|
Iouw2 mean power (modulated) |
dBm |
-46 |
|
Fuw1 (offset) (NOTE 2) |
MHz |
10 |
-10 |
Fuw2 (offset) (NOTE 2) |
MHz |
20 |
-20 |
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) N OTE 3 |
|
NOTE 1: Iouw2 (modulated) consists of the common channels needed for tests as specified in Table C.7 and 16 dedicated data channels as specified in Table C.6. NOTE 2: For DC-HSUPA, negative offset refers to the assigned channel frequency of the lowest carrier frequency used and positive offset refers to the assigned channel frequency of the highest carrier frequency used. NOTE 3 :The UE transmitted mean power shall be reduced by 0.5dB for a UE operating in band XXII. |
Table 7.9AC: Reference input powers for intermod, DC-HSUPA.
Operating Band |
Unit |
HS-PDSCH_Ec |
Îor |
I |
dBm/3.84 MHz |
-105 |
-94.7 |
II |
dBm/3.84 MHz |
-105.3 |
-95 |
III |
dBm/3.84 MHz |
-104.1 |
-93.8 |
IV |
dBm/3.84 MHz |
-105 |
-94.7 |
V |
dBm/3.84 MHz |
-102 |
-91.7 |
VI |
dBm/3.84 MHz |
-102.2 |
-91.9 |
VII |
dBm/3.84 MHz |
-105.3 |
-95 |
VIII |
dBm/3.84 MHz |
-99.8 |
-89.5 |
IX |
dBm/3.84 MHz |
-104.6 |
-94.3 |
X |
dBm/3.84 MHz |
-105 |
-94.7 |
XI |
dBm/3.84 MHz |
-100 |
-89.7 |
XII |
dBm/3.84 MHz |
N/A |
N/A |
XIII |
dBm/3.84 MHz |
N/A |
N/A |
XIV |
dBm/3.84 MHz |
N/A |
N/A |
XIX |
dBm/3.84 MHz |
-102.2 |
-91.9 |
XX |
dBm/3.84 MHz |
TBD |
TBD |
XXI |
dBm/3.84 MHz |
-100 |
-89.7 |
XXII |
dBm/3.84 MHz |
-104.1 |
-93.8 |
XXV |
dBm/3.84 MHz |
-103.5 |
-93.2 |
XXVI |
dBm/3.84 MHz |
-99.8 |
-89.5 |
NOTE 1 For the UE which supports both Band III and Band IX operating frequencies, the reference sensitivity level of TBD dBm <REF_Ec,intermod> shall apply for Band IX. The corresponding <REFÎor,intermod> is TBD dBm NOTE 2 For the UE which supports both Band XI and Band XXI operating frequencies, the reference input power level is FFS. NOTE 3 For the UE which supports DB-DC-HSDPA configuration in Table 5.0aA the < HS-PDSCH_Ec > and < Îor > are allowed to be increased by an amount defined in Table 7.12. NOTE 4 For the UE which supports dual band 4C-HSDPA configuration in Table 5.0aC the < HS-PDSCH_Ec > and < Îor > are allowed to be increased by an amount defined in Table 7.13. |
7.8.1C Additional requirement for single band 4C-HSDPA
7.8.1C.1 Single uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9AD and Table 7.9AE.
Table 7.9AD: Test parameters for receive intermodulation characteristics, single band 4C-HSDPA, single uplink operation
Parameter |
Unit |
Level |
|
Iouw1 (CW) |
dBm |
-46 |
|
Iouw2 mean power (modulated) |
dBm |
-46 |
|
Fuw1 (offset) (NOTE 2) |
MHz |
10 |
-10 |
Fuw2 (offset) (NOTE 2) |
MHz |
20 |
-20 |
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
|
NOTE 1: Iouw2 (modulated) consists of the common channels needed for tests as specified in Table C.7 and 16 dedicated data channels as specified in Table C.6. NOTE 2: For single band 4C-HSDPA, negative offset refers to the assigned channel frequency of the lowest carrier frequencies, and positive offset refers to the assigned channel frequency of the highest carrier frequencies. |
Table 7.9AE: Intermodulation requirements, single band 4C-HSDPA, single uplink operation
Single band 4C-HSDPA Configuration |
DL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UL-DL carrier separation |
I-3 |
I |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
II-3, II-4 |
II |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
NOTE: <REFSENS> and <REFÎor> refer to the HS-PDSCH_Ec<REFSENS> and the HS-PDSCH<REFÎor> as specified in Table 7.2C for single band 4C-HSDPA. |
7.8.1C.2 Dual uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9AF and Table 7.9AG.
Table 7.9AF: Receive intermodulation characteristics for single band 4C-HSDPA, dual uplink operation
Parameter |
Unit |
Level |
|
Iouw1 (CW) |
dBm |
-46 |
|
Iouw2 mean power (modulated) |
dBm |
-46 |
|
Fuw1 (offset) (NOTE 2) |
MHz |
10 |
-10 |
Fuw2 (offset) (NOTE 2) |
MHz |
20 |
-20 |
NOTE 1: Iouw2 (modulated) consists of the common channels needed for tests as specified in Table C.7 and 16 dedicated data channels as specified in Table C.6. NOTE 2: For single band 4C-HSDPA, negative offset refers to the assigned channel frequency of the lowest carrier frequencies, and positive offset refers to the assigned channel frequency of the highest carrier frequencies. |
Table 7.9AG: Intermodulation requirements, single band 4C-HSDPA, dual uplink operation
Single band 4C-HSDPA Configuration |
DL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UE transmitted mean power (dBm) |
UL-DL carrier separation |
I-3 |
I |
-105 |
-94.7 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
II-3, II-4 |
II |
-105.3 |
-95.0 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
NOTE 1 For the UE which supports DB-DC-HSDPA configuration in Table 5.0aA the < HS-PDSCH_Ec > and < Îor > are allowed to be increased by an amount defined in Table 7.12. NOTE 2 For the UE which supports dual band 4C-HSDPA configuration in Table 5.0aC the < HS-PDSCH_Ec > and < Îor > are allowed to be increased by an amount defined in Table 7.13. |
7.8.1D Additional requirement for dual band 4C-HSDPA
7.8.1D.1 Single uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9AH and Table 7.9AI.
Table 7.9AH: Test parameters for receive intermodulation characteristics, dual band 4C-HSDPA, single uplink operation
Parameter |
Unit |
Level |
|
Iouw1 (CW) |
dBm |
-46 |
|
Iouw2 mean power (modulated) |
dBm |
-46 |
|
Fuw1 (offset) (NOTE 2) |
MHz |
10 |
-10 |
Fuw2 (offset) (NOTE 2) |
MHz |
20 |
-20 |
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
|
NOTE 1: Iouw2 (modulated) consists of the common channels needed for tests as specified in Table C.7 and 16 dedicated data channels as specified in Table C.6. NOTE 2: For dual band 4C-HSDPA, negative offset refers to the assigned channel frequency of the lowest carrier frequenc(ies) in each band, and positive offset refers to the assigned channel frequency of the highest carrier frequenc(ies) in each band. |
Table 7.9AI: Intermodulation requirements, dual band 4C-HSDPA, single uplink operation
Dual band 4C-HSDPA Configuration |
DL Band |
UL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UL-DL carrier separation |
I-2-VIII-1 I-3-VIII-1, I-2-VIII-2, I-1-VIII-2 |
I |
I |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
VIII |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
||
I |
VIII |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
|
VIII |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
||
II-1-IV-2 II-2-IV-1 II-2-IV-2 |
II |
II |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
IV |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
||
II |
IV |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
|
IV |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
||
I-1-V-2 I-2-V-1 I-2-V-2 |
I |
I |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
V |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
||
I |
V |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
|
V |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
||
II-1-V-2 |
II |
I |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
V |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
||
II |
V |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
|
V |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
||
I-1-XXXII-2 I-2-XXXII-1 |
I |
I |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
XXXII |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
||
NOTE: <REFSENS> and <REFÎor> refer to the HS-PDSCH_Ec<REFSENS> and the HS-PDSCH<REFÎor> as specified in Table 7.2D for dual band 4C-HSDPA. |
7.8.1D.2 Dual uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9AJ and Table 7.9AK.
Table 7.9AJ: Receive intermodulation characteristics for dual band 4C-HSDPA, dual uplink operation
Parameter |
Unit |
Level |
|
Iouw1 (CW) |
dBm |
-46 |
|
Iouw2 mean power (modulated) |
dBm |
-46 |
|
Fuw1 (offset) (NOTE 2) |
MHz |
10 |
-10 |
Fuw2 (offset) (NOTE 2) |
MHz |
20 |
-20 |
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
|
NOTE 1: Iouw2 (modulated) consists of the common channels needed for tests as specified in Table C.7 and 16 dedicated data channels as specified in Table C.6. NOTE 2: For dual band 4C-HSDPA, negative offset refers to the assigned channel frequency of the lowest carrier frequenc(ies) in each band, and positive offset refers to the assigned channel frequency of the highest carrier frequenc(ies) in each band. |
Table 7.9AK: Intermodulation requirements, dual band 4C-HSDPA, dual uplink operation
Dual band 4C-HSDPA Configuration |
DL Band |
UL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UE transmitted mean power (dBm) |
UL-DL carrier separation |
I-2-VIII-1 I-3-VIII-1 |
I |
I |
-104.2 |
-93.9 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
VIII |
-103.6 |
-93.3 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
I-2-VIII-2 |
I |
I |
-104.2 |
-93.9 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
VIII |
-103.6 |
-93.3 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
I |
VIII |
-104.8 |
-94.5 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
|
VIII |
-98.7 |
-88.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
I-1-VIII-2 |
I |
VIII |
-104.8 |
-94.5 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
VIII |
-98.7 |
-88.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
II-1-IV-2 |
II |
IV |
-103.1 |
-92.8 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
IV |
-103.4 |
-93.1 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
II-2-IV-1 |
II |
II |
-103.1 |
-92.8 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
IV |
-103.4 |
-93.1 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
II-2-IV-2 |
II |
II |
-103.1 |
-92.8 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
IV |
-103.4 |
-93.1 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
II |
IV |
-103.1 |
-92.8 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
|
IV |
-103.4 |
-93.1 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
I-1-V-2 |
I |
V |
-104.2 |
-93.9 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
V |
-101.1 |
-90.8 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
I-2-V-1 |
I |
I |
-104.2 |
-93.9 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
V |
-103.9 |
-93.6 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
I-2-V-2 |
I |
I |
-104.2 |
-93.9 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
V |
-103.9 |
-93.6 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
I |
V |
-104.2 |
-93.9 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
|
V |
-101.1 |
-90.8 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
II-1-V-2 |
II |
V |
-104.4 |
-94.1 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
V |
-101.1 |
-90.8 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
I-2-XXXII-1 |
I |
I |
-104.7 |
-94.4 |
20 (for Power class 3 and 3bis) |
Minimum |
XXXII |
-104.7 |
-94.4 |
20 (for Power class 3 and 3bis) |
Minimum |
7.8.1E Additional requirement for single band 8C-HSDPA
7.8.1E.1 Single uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9AL and Table 7.9AM.
Table 7.9AL: Test parameters for receive intermodulation characteristics, single band 8C-HSDPA, single uplink operation
Parameter |
Unit |
Level |
|
Iouw1 (CW) |
dBm |
-46 |
|
Iouw2 mean power (modulated) |
dBm |
-46 |
|
Fuw1 (offset) (NOTE 2) |
MHz |
10 |
-10 |
Fuw2 (offset) (NOTE 2) |
MHz |
20 |
-20 |
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
|
NOTE 1: Iouw2 (modulated) consists of the common channels needed for tests as specified in Table C.7 and 16 dedicated data channels as specified in Table C.6. NOTE 2: For single band 8C-HSDPA, negative offset refers to the assigned channel frequency of the lowest carrier frequency, and positive offset refers to the assigned channel frequency of the highest carrier frequency. |
Table 7.9AM: Intermodulation requirements, single band 8C-HSDPA, single uplink operation
Single band 8C-HSDPA Configuration |
DL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UL-DL carrier separation |
I-8 |
I |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
NOTE: <REFSENS> and <REFÎor> refer to the HS-PDSCH_Ec<REFSENS> and the HS-PDSCH<REFÎor> as specified in Table 7.2E for single band 8C-HSDPA. |
7.8.1E.2 Dual uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9AN and Table 7.9AO.
Table 7.9AN: Receive intermodulation characteristics for single band 8C-HSDPA, dual uplink operation
Parameter |
Unit |
Level |
|
Iouw1 (CW) |
dBm |
-46 |
|
Iouw2 mean power (modulated) |
dBm |
-46 |
|
Fuw1 (offset) (NOTE 2) |
MHz |
10 |
-10 |
Fuw2 (offset) (NOTE 2) |
MHz |
20 |
-20 |
NOTE 1: Iouw2 (modulated) consists of the common channels needed for tests as specified in Table C.7 and 16 dedicated data channels as specified in Table C.6. NOTE 2: For single band 8C-HSDPA, negative offset refers to the assigned channel frequency of the lowest carrier frequency, and positive offset refers to the assigned channel frequency of the highest carrier frequency. |
Table 7.9AO: Intermodulation requirements, single band 8C-HSDPA, dual uplink operation
Single band 8C-HSDPA Configuration |
DL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UE transmitted mean power (dBm) |
UL-DL carrier separation |
I-8 |
I |
-105 |
-94.7 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
NOTE 1 For the UE which supports DB-DC-HSDPA configuration in Table 5.0aA the < HS-PDSCH_Ec > and < Îor > are allowed to be increased by an amount defined in Table 7.12. NOTE 2 For the UE which supports dual band 4C-HSDPA configuration in Table 5.0aC the < HS-PDSCH_Ec > and < Îor > are allowed to be increased by an amount defined in Table 7.13. |
7.8.1F Additional requirement for single band NC-4C-HSDPA
7.8.1F.1 Single uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9AP and Table 7.9AQ.
Table 7.9AP: Test parameters for receive intermodulation characteristics, single band NC-4C-HSDPA, single uplink operation
Parameter |
Unit |
Level |
|
Iouw1 (CW) |
dBm |
-46 |
|
Iouw2 mean power (modulated) |
dBm |
-46 |
|
Fuw1 (offset) (NOTE 2) |
MHz |
10 |
-10 |
Fuw2 (offset) (NOTE 2) |
MHz |
20 |
-20 |
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
|
NOTE 1: Iouw2 (modulated) consists of the common channels needed for tests as specified in Table C.7 and 16 dedicated data channels as specified in Table C.6. NOTE 2: For single band NC-4C-HSPDA out-of-gap, negative offset refers to the assigned channel frequency of the lowest carrier belonging to the lower subblock of carriers, and positive offset refers to the assigned channel frequency of the highest carrier belonging to the higher subblock of carriers. |
Table 7.9AQ: Intermodulation requirements, single band NC-4C-HSDPA, single uplink operation
Single band NC-4C-HSDPA Configuration |
Test type |
DL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UL-DL carrier separation |
|
I-1-5-1, I-2-5-1, I-3-10-1 |
Out-of-gap |
I |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
|
IV-1-5-1, IV-2-10-1, IV-2-15-2, IV-2-20-1, IV-2-25-2 |
Out-of-gap |
IV |
<REFSENS>+3 dB |
<REFÎor>+3 dB |
Minimum |
|
NOTE: <REFSENS> and <REFÎor> refer to the HS-PDSCH_Ec<REFSENS> and the HS-PDSCH<REFÎor> as specified in Table 7.2E for single band NC-4C-HSDPA. |
7.8.1F.2 Dual uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9AR and Table 7.9AS.
Table 7.9AR: Receive intermodulation characteristics for single band NC-4C-HSDPA, dual uplink operation
Parameter |
Unit |
Level |
|
Iouw1 (CW) |
dBm |
-46 |
|
Iouw2 mean power (modulated) |
dBm |
-46 |
|
Fuw1 (offset) (NOTE 2) |
MHz |
10 |
-10 |
Fuw2 (offset) (NOTE 2) |
MHz |
20 |
-20 |
NOTE 1: Iouw2 (modulated) consists of the common channels needed for tests as specified in Table C.7 and 16 dedicated data channels as specified in Table C.6. NOTE 2: For single band NC-4C-HSPDA out-of-gap, negative offset refers to the assigned channel frequency of the lowest carrier belonging to the lower subblock of carriers, and positive offset refers to the assigned channel frequency of the highest carrier belonging to the higher subblock of carriers. |
Table 7.9AS: Intermodulation requirements, single band NC-4C-HSDPA, dual uplink operation
Single band NC-4C-HSDPA Configuration |
Test type |
DL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UE transmitted mean power (dBm) |
UL-DL carrier separation |
I-2-5-1, I-3-10-1 |
Out-of-gap |
I |
-105 |
-94.7 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
IV-2-10-1, IV-2-15-2, IV-2-20-1, IV-2-25-2 |
Out-of-gap |
IV |
-104.7 |
-94.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
NOTE 1 For the UE which supports DB-DC-HSDPA configuration in Table 5.0aA the < HS-PDSCH_Ec > and < Îor > are allowed to be increased by an amount defined in Table 7.12. NOTE 2 For the UE which supports dual band 4C-HSDPA configuration in Table 5.0aC the < HS-PDSCH_Ec > and < Îor > are allowed to be increased by an amount defined in Table 7.13. |
7.8.2 Minimum requirement (Narrow band)
The BER shall not exceed 0.001 for the parameters specified in Table 7.9A.
Table 7.9A: Receive intermodulation characteristics
Parameter |
Unit |
Band II, IV, V, X, XXV, XXVI |
Band III, VIII, XII, XIII, XIV |
||
DPCH_Ec |
dBm/3.84 MHz |
<REFSENS>+ 10 dB |
<REFSENS>+ 10 dB |
||
Îor |
dBm/3.84 MHz |
<REFÎor> + 10 dB |
<REFÎor> +10 dB |
||
Iouw1 (CW) |
dBm |
-44 |
-43 |
||
Iouw2 (GMSK) |
dBm |
-44 |
-43 |
||
Fuw1 (offset) |
MHz |
3.5 |
-3.5 |
3.6 |
-3.6 |
Fuw2 (offset) |
MHz |
5.9 |
-5.9 |
6.0 |
-6.0 |
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
|||
NOTE 1: Iouw2 (GMSK) is an interfering signal as defined in TS 45.004 [6]. NOTE 2: <REFSENS> and <REFÎor> refer to the DPCH_Ec<REFSENS> and the DPCH<REFÎor> as specified in Table 7.2. |
7.8.2A Additional requirement for DC-HSDPA and DB-DC-HSDPA (Narrow band)
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9B.
Table 7.9B: Receive intermodulation characteristics
Parameter |
Unit |
Band II, IV, V, X, XXV, XXVI |
Band III, VIII, XII, XIII, XIV |
||
HS-PDSCH_Ec |
dBm/3.84 MHz |
<REFSENS>+ 10 dB |
<REFSENS>+ 10 dB |
||
Îor |
dBm/3.84 MHz |
<REFÎor> + 10 dB |
<REFÎor> +10 dB |
||
Iouw1 (CW) |
dBm |
-44 |
-43 |
||
Iouw2 (GMSK) |
dBm |
-44 |
-43 |
||
Fuw1 (offset) (NOTE 2) |
MHz |
3.5 |
-3.5 |
3.6 |
-3.6 |
Fuw2 (offset) (NOTE 2) |
MHz |
5.9 |
-5.9 |
6.0 |
-6.0 |
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
|||
NOTE 1: Iouw2 (GMSK) is an interfering signal as defined in TS 45.004 [6]. NOTE 2: For DC-HSDPA, negative offset refers to the assigned channel frequency of the lowest carrier frequency used and positive offset refers to the assigned channel frequency of the highest carrier frequency used. For DB-DC-HSDPA, offset refers to the assigned channel frequencies of the individual cells. NOTE3: <REFSENS> and <REFÎor> refers to the HS-PDSCH_Ec<REFSENS> and the HS-PDSCH<REFÎor> as specified in Table 7.2A for DC-HSDPA and Table 7.2B for DB-DC-HSDPA. |
7.8.2B Additional requirement for DC-HSUPA (Narrow band)
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9C and Table 7.9D.
Table 7.9C: Receive intermodulation characteristics
Parameter |
Unit |
Band II, IV, V, X,XXV, XXVI |
Band III, VIII, XII, XIII, XIV |
||
Iouw1 (CW) |
dBm |
-44 |
-43 |
||
Iouw2 (GMSK) |
dBm |
-44 |
-43 |
||
Fuw1 (offset) (NOTE 2) |
MHz |
3.5 |
-3.5 |
3.6 |
-3.6 |
Fuw2 (offset) (NOTE 2) |
MHz |
5.9 |
-5.9 |
6.0 |
-6.0 |
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
|||
NOTE 1: Iouw2 (GMSK) is an interfering signal as defined in TS 45.004 [6]. NOTE 2: For DC-HSUPA, negative offset refers to the assigned channel frequency of the lowest carrier frequency used and positive offset refers to the assigned channel frequency of the highest carrier frequency used. |
Table 7.9D: Reference input powers for intermodulation, narrow-band, DC-HSUPA.
Operating Band |
Unit |
HS-PDSCH_Ec |
Îor |
II |
dBm/3.84 MHz |
-86.9 |
-76.6 |
III |
dBm/3.84 MHz |
-85.7 |
-75.4 |
IV |
dBm/3.84 MHz |
-86.9 |
-76.6 |
V |
dBm/3.84 MHz |
-86.9 |
-76.6 |
VIII |
dBm/3.84 MHz |
-85.6 |
-75.3 |
X |
dBm/3.84 MHz |
-86.9 |
-76.6 |
XII |
dBm/3.84 MHz |
N/A |
N/A |
XIII |
dBm/3.84 MHz |
N/A |
N/A |
XIV |
dBm/3.84 MHz |
N/A |
N/A |
XXV |
dBm/3.84 MHz |
-84.7 |
-74.4 |
XXVI |
dBm/3.84 MHz |
-85.6 |
-75.3 |
NOTE 1 For the UE which supports DB-DC-HSDPA configuration in Table 5.0aA the < HS-PDSCH_Ec > and < Îor > are allowed to be increased by an amount defined in Table 7.12. NOTE 2 For the UE which supports dual band 4C-HSDPA configuration in Table 5.0aC the < HS-PDSCH_Ec > and < Îor > are allowed to be increased by an amount defined in Table 7.13. |
7.8.2C Additional requirement for single band 4C-HSDPA (Narrow band)
7.8.2C.1 Single uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9DA and Table 7.9DB.
Table 7.9DA: Test parameters for receive narrow-band intermodulation characteristics, single band 4C-HSDPA, single uplink operation
Parameter |
Unit |
Band II |
|
Iouw1 (CW) |
dBm |
-44 |
|
Iouw2 (GMSK) |
dBm |
-44 |
|
Fuw1 (offset) (NOTE 2) |
MHz |
3.5 |
-3.5 |
Fuw2 (offset) (NOTE 2) |
MHz |
5.9 |
-5.9 |
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
|
NOTE 1: Iouw2 (GMSK) is an interfering signal as defined in TS 45.004 [6]. NOTE 2: For single band 4C-HSDPA, negative offset refers to the assigned channel frequency of the lowest carrier frequencies, and positive offset refers to the assigned channel frequency of the highest carrier frequencies. |
Table 7.9DB: Narrow-band intermodulation requirements, single band 4C-HSDPA, single uplink operation
Single band 4C-HSDPA Configuration |
DL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UL-DL carrier separation |
II-3, II-4 |
II |
<REFSENS>+15.5 dB |
<REFÎor>+15.5 dB |
Minimum |
NOTE: <REFSENS> and <REFÎor> refers to the HS-PDSCH_Ec<REFSENS> and the HS-PDSCH<REFÎor> as specified in Table 7.2C for single band 4C-HSDPA. |
7.8.2C.2 Dual uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9DC and Table 7.9DD.
Table 7.9DC: Test parameters for receive narrow-band intermodulation characteristics, single band 4C-HSDPA, dual uplink operation
Parameter |
Unit |
Band II |
|
Iouw1 (CW) |
dBm |
-44 |
|
Iouw2 (GMSK) |
dBm |
-44 |
|
Fuw1 (offset) (NOTE 2) |
MHz |
3.5 |
-3.5 |
Fuw2 (offset) (NOTE 2) |
MHz |
5.9 |
-5.9 |
NOTE 1: Iouw2 (GMSK) is an interfering signal as defined in TS 45.004 [6]. NOTE 2: For single band 4C-HSDPA, negative offset refers to the assigned channel frequency of the lowest carrier frequencies, and positive offset refers to the assigned channel frequency of the highest carrier frequencies. |
Table 7.9DD: Narrow-band intermodulation requirements, single band 4C-HSDPA, dual uplink operation
Single band 4C-HSDPA Configuration |
DL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UE transmitted mean power (dBm) |
UL-DL carrier separation |
II-3, II-4 |
II |
-86.9 |
-76.6 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
7.8.2D Additional requirement for dual band 4C-HSDPA (Narrow band)
7.8.2D.1 Single uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9E and Table 7.9F.
Table 7.9E: Test parameters for receive narrow-band intermodulation characteristics, dual band 4C-HSDPA, single uplink operation
Parameter |
Unit |
Band II, IV, V |
Band VIII |
||
Iouw1 (CW) |
dBm |
-44 |
-43 |
||
Iouw2 (GMSK) |
dBm |
-44 |
-43 |
||
Fuw1 (offset) (NOTE 2) |
MHz |
3.5 |
-3.5 |
3.6 |
-3.6 |
Fuw2 (offset) (NOTE 2) |
MHz |
5.9 |
-5.9 |
6.0 |
-6.0 |
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
|||
NOTE 1: Iouw2 (GMSK) is an interfering signal as defined in TS 45.004 [6]. NOTE 2: For dual band 4C-HSDPA, negative offset refers to the assigned channel frequency of the lowest carrier frequenc(ies) in each band, and positive offset refers to the assigned channel frequency of the highest carrier frequenc(ies) in each band. |
Table 7.9F: Narrow-band intermodulation requirements, dual band 4C-HSDPA, single uplink operation
Dual band 4C-HSDPA Configuration |
DL Band |
UL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UL-DL carrier separation |
I-2-VIII-1 I-3-VIII-1 I-2-VIII-2 I-1-VIII-2 |
VIII |
I |
<REFSENS>+16.6 dB |
<REFÎor>+16.6 dB |
Minimum |
VIII |
VIII |
<REFSENS>+16.6 dB |
<REFÎor>+16.6 dB |
Minimum |
|
II-1-IV-2 II-2-IV-1 II-2-IV-2 |
II |
II |
<REFSENS>+17 dB |
<REFÎor>+17 dB |
Minimum |
IV |
<REFSENS>+18.9 dB |
<REFÎor>+18.9 dB |
Minimum |
||
II |
IV |
<REFSENS>+17 dB |
<REFÎor>+17 dB |
Minimum |
|
IV |
<REFSENS>+18.9 dB |
<REFÎor>+18.9 dB |
Minimum |
||
I-1-V-2 I-2-V-1 I-2-V-2 |
V |
I |
<REFSENS>+17 dB |
<REFÎor>+17 dB |
Minimum |
V |
V |
<REFSENS>+17 dB |
<REFÎor>+17 dB |
Minimum |
|
II-1-V-2 |
II |
II |
<REFSENS>+16.5 dB |
<REFÎor>+16.5dB |
Minimum |
V |
<REFSENS>+16.5 dB |
<REFÎor>+16.5dB |
Minimum |
||
II |
V |
<REFSENS>+16.5dB |
<REFÎor>+16.5 dB |
Minimum |
|
V |
<REFSENS>+16.5dB |
<REFÎor>+16.5dB |
Minimum |
||
NOTE: <REFSENS> and <REFÎor> refers to the HS-PDSCH_Ec<REFSENS> and the HS-PDSCH<REFÎor> as specified in Table 7.2D for dual band 4C-HSDPA. |
7.8.2D.2 Dual uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9G and Table 7.9H.
Table 7.9G: Test parameters for receive narrow-band intermodulation characteristics, dual band 4C-HSDPA, dual uplink operation
Parameter |
Unit |
Band II, IV, V |
Band VIII |
||
Iouw1 (CW) |
dBm |
-44 |
-43 |
||
Iouw2 (GMSK) |
dBm |
-44 |
-43 |
||
Fuw1 (offset) (NOTE 2) |
MHz |
3.5 |
-3.5 |
3.6 |
-3.6 |
Fuw2 (offset) (NOTE 2) |
MHz |
5.9 |
-5.9 |
6.0 |
-6.0 |
NOTE 1: Iouw2 (GMSK) is an interfering signal as defined in TS 45.004 [6]. NOTE 2: For dual band 4C-HSDPA, negative offset refers to the assigned channel frequency of the lowest carrier frequenc(ies) in each band, and positive offset refers to the assigned channel frequency of the highest carrier frequenc(ies) in each band. |
Table 7.9H: Narrow-band intermodulation requirements, dual band 4C-HSDPA, dual uplink operation
Dual band 4C-HSDPA Configuration |
DL Band |
UL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UE transmitted mean power (dBm) |
UL-DL carrier separation |
I-2-VIII-1 I-3-VIII-1 |
VIII |
I |
-84.7 |
-74.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
I-2-VIII-2 |
VIII |
I |
-84.7 |
-74.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
VIII |
VIII |
-84.6 |
-74.3 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
|
I-1-VIII-2 |
VIII |
VIII |
-84.6 |
-74.3 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
II-1-IV-2 |
II |
IV |
-84.7 |
-74.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
IV |
-84.7 |
-74.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
II-2-IV-1 |
II |
II |
-84.7 |
-74.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
IV |
-84.7 |
-74.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
II-2-IV-2 |
II |
II |
-84.7 |
-74.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
IV |
-84.7 |
-74.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
II |
IV |
-84.7 |
-74.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
|
IV |
-84.7 |
-74.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
||
I-1-V-2 |
V |
V |
-85.7 |
-75.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
I-2-V-1 |
V |
I |
-85.7 |
-75.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
I-2-V-2 |
V |
I |
-85.7 |
-75.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
V |
V |
-85.7 |
-75.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
|
II-1-V-2 |
II |
V |
-85.7 |
-75.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
V |
-85.7 |
-75.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
7.8.2E Additional requirement for single band NC-4C-HSDPA (Narrow band)
7.8.2E.1 Single uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9I and Table 7.9J.
Table 7.9I: Test parameters for receive narrow-band intermodulation characteristics, single band NC-4C-HSDPA, single uplink operation
Parameter |
Unit |
Band IV |
|
Iouw1 (CW) |
dBm |
-44 |
|
Iouw2 (GMSK) |
dBm |
-44 |
|
Fuw1 (offset) (NOTE 2) |
MHz |
3.5 |
-3.5 |
Fuw2 (offset) (NOTE 2) |
MHz |
5.9 |
-5.9 |
UE transmitted mean power |
dBm |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
|
NOTE 1: Iouw2 (GMSK) is an interfering signal as defined in TS 45.004 [6]. NOTE 2: For single band NC-4C-HSPDA out-of-gap, negative offset refers to the assigned channel frequency of the lowest carrier belonging to the lower subblock of carriers, and positive offset refers to the assigned channel frequency of the highest carrier belonging to the higher subblock of carriers. |
Table 7.9J: Narrow-band intermodulation requirements, single band NC-4C-HSDPA, single uplink operation
Single band NC-4C-HSDPA Configuration |
Test type |
DL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UL-DL carrier separation |
IV-1-5-1, IV-2-10-1, IV-2-15-2, IV-2-20-1, IV-2-25-2 |
Out-of-gap |
IV |
<REFSENS>+10 dB |
<REFÎor>+10 dB |
Minimum |
NOTE: <REFSENS> and <REFÎor> refers to the HS-PDSCH_Ec<REFSENS> and the HS-PDSCH<REFÎor> as specified in Table 7.2E for single band NC-4C-HSDPA. |
7.8.2E.2 Dual uplink operation
The BLER measured on each individual cell shall not exceed 0.1 for the parameters specified in Table 7.9K and Table 7.9L.
Table 7.9DC: Test parameters for receive narrow-band intermodulation characteristics, single band NC-4C-HSDPA, dual uplink operation
Parameter |
Unit |
Band IV |
|
Iouw1 (CW) |
dBm |
-44 |
|
Iouw2 (GMSK) |
dBm |
-44 |
|
Fuw1 (offset) (NOTE 2) |
MHz |
3.5 |
-3.5 |
Fuw2 (offset) (NOTE 2) |
MHz |
5.9 |
-5.9 |
NOTE 1: Iouw2 (GMSK) is an interfering signal as defined in TS 45.004 [6]. NOTE 2: For single band NC-4C-HSPDA out-of-gap, negative offset refers to the assigned channel frequency of the lowest carrier belonging to the lower subblock of carriers, and positive offset refers to the assigned channel frequency of the highest carrier belonging to the higher subblock of carriers. |
Table 7.9L: Narrow-band intermodulation requirements, single band NC-4C-HSDPA, dual uplink operation
Single band NC-4C-HSDPA Configuration |
Test type |
DL Band |
HS-PDSCH_Ec (dBm/3.84MHz) |
Îor (dBm/3.84MHz) |
UE transmitted mean power (dBm) |
UL-DL carrier separation |
IV-2-10-1, IV-2-15-2, IV-2-20-1, IV-2-25-2 |
Out-of-gap |
IV |
-86.7 |
-76.4 |
20 (for Power class 3 and 3bis) 18 (for Power class 4) |
Minimum |
NOTE 1 For the UE which supports DB-DC-HSDPA configuration in Table 5.0aA the < HS-PDSCH_Ec > and < Îor > are allowed to be increased by an amount defined in Table 7.12. NOTE 2 For the UE which supports dual band 4C-HSDPA configuration in Table 5.0aC the < HS-PDSCH_Ec > and < Îor > are allowed to be increased by an amount defined in Table 7.13. |