9.6 Requirements for HS-DSCH and HS-SCCH reception in CELL_FACH state
25.1013GPPRelease 17TSUser Equipment (UE) radio transmission and reception (FDD)
The requirements determined in this section apply for UE being able to receive HS-DSCH and HS-SCCH in CELL_FACH state.
9.6.1 HS-DSCH demodulation requirements (Single Link)
The receiver single link performance of the High Speed Physical Downlink Shared Channel (HS-DSCH) is determined by the RLC SDU error rate (RLC SDU ER).
9.6.1.1 Requirement QPSK, Fixed Reference Channel (FRC) H-Set 3
The requirements are specified in terms of a minimum RLC SDU error rate (RLC SDU ER) for the DL reference channel H-Set 3 (QPSK version) specified in A.7.1.3, with the addition of the parameters in Table 9.61 and the downlink physical channel setup according to Table C.12A. For the test parameters specified in Table 9.61, for the value of HS-DSCH-1 Ec/Ior specified in Table 9.62 the measured RLC SDU ER shall be less than or equal to the corresponding specified value of RLC SDU ER.
Table 9.61: Test Parameters for Testing QPSK FRCs H-Set 3
|
Parameter |
Unit |
Test 1 |
||||||
|
Phase reference |
P-CPICH |
|||||||
|
|
dBm/3.84 MHz |
-60 |
||||||
|
Redundancy and constellation version coding sequence |
{0,2,5,6} |
|||||||
|
Number of HARQ transmission |
4 |
|||||||
|
NOTE: The HS-SCCH-1 and HS-PDSCH shall be transmitted continuously with constant power. HS-SCCH-1 shall only use the identity of the UE under test for those TTI intended for the UE. NOTE: The HS-PDSCH is transmitted using all four HARQ transmissions cycling through the different redundancy and constellation versions. |
||||||||
Table 9.62: Minimum requirement QPSK, Fixed Reference Channel (FRC) H-Set 3
|
Test Number |
Propagation Conditions |
Reference value |
|
|
HS-PDSCH |
RLC SDU ER |
||
|
1 |
VA30 |
-6 |
0.82 |
(dB)
= 0 dB9.6.2 HS-SCCH Detection Performance
The detection performance of the HS-SCCH is determined by RLC SDU error rate (RLC SDU ER).
9.6.2.1 HS-SCCH Type 1 Single Link Performance
For the test parameters specified in Table 9.63, for the value of HS-SCCH-1 Ec/Ior specified in Table 9.64 the measured RLC SDU ER shall be less than or equal to the corresponding specified value of RLC SDU ER. The downlink physical channel setup according to Table C.12B.
Table 9.63: Test parameters for HS-SCCH detection – single link
|
Parameter |
Unit |
Test 1 |
Test 2 |
Test 3 |
|||
|
|
dBm/3.84 MHz |
-60 |
|||||
|
Phase reference |
– |
P-CPICH |
|||||
|
P-CPICH |
dB |
-10 |
|||||
|
HS-SCCH UE Identity ( |
HS-SCCH-1: 1010101010101010 |
||||||
|
HS-DSCH TF of UE1 |
TF corresponding to CQI1 |
||||||
|
HS-SCCH-1 transmission pattern |
The HS-SCCH-1 shall be transmitted continuously with constant power. |
||||||
|
HS-PDSCH transmission pattern |
The HS-PDSCH shall be transmitted continuously with constant power, without re-transmissions. |
||||||
|
HS-SCCH-1 TTI Signalling Pattern |
– |
The identity of the UE under test shall be used on every fourth TTI. |
|||||
,
, …, 
)Table 9.64: Minimum requirement for HS-SCCH detection – single link
|
Test Number |
Propagation Conditions |
Reference value |
||
|
HS-SCCH-1 |
|
RLC SDU ER |
||
|
3 |
VA30 |
-10 |
0 |
0.01 |
(dB)
(dB)