7.3 Reference sensitivity
38.101-13GPPNRPart 1: Range 1 StandaloneRelease 17TSUser Equipment (UE) radio transmission and reception
7.3.1 General
The reference sensitivity power level REFSENS is the minimum mean power applied to each one of the UE antenna ports for all UE categories, at which the throughput shall meet or exceed the requirements for the specified reference measurement channel.
In later clauses of Clause 7 where the value of REFSENS is used as a reference to set the corresponding requirement:
in all bands, the UE shall be verified against those requirements by applying the REFSENS value in Table 7.3.2-1a, Table 7.3.2-1b and Table 7.3.2-1c or Table 7.3.2-1d with 2 Rx antenna ports tested;
for bands where the UE is required to be equipped with 4 Rx antenna ports, the UE shall additionally be verified against those requirements by applying the resulting REFSENS value derived from the requirement in Table 7.3.2-2 with 4 Rx antenna ports tested.
7.3.2 Reference sensitivity power level
The throughput shall be ≥ 95 % of the maximum throughput of the reference measurement channels as specified in Annexes A.2.2.2, A3.2 and A.3.3 (with one sided dynamic OCNG Pattern OP.1 FDD/TDD for the DL-signal as described in Annex A.5.1.1/A.5.2.1) with parameters specified in Table 7.3.2-1a, Table 7.3.2-1b, Table 7.3.2-1c, Table 7.3.2-1d and Table 7.3.2-2.
Table 7.3.2-1a: Two antenna port reference sensitivity QPSK PREFSENS for FDD bands
|
Operating band / SCS / Channel bandwidth |
|||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
|
Operating Band |
SCS kHz |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
25 MHz |
30 MHz (dBm) |
35 MHz (dBm) |
40 MHz |
45 MHz (dBm) |
50 MHz |
|
n1 |
15 |
-100.0 |
-96.8 |
-95.0 |
-93.8 |
-92.7 |
-91.9 |
-90.6 |
-90.1 |
-89.6 |
|
|
30 |
-97.1 |
-95.1 |
-94.0 |
-92.8 |
-92.0 |
-90.7 |
-90.2 |
-89.7 |
|||
|
60 |
-97.5 |
-95.4 |
-94.2 |
-93.0 |
-92.1 |
-90.9 |
-90.3 |
-89.7 |
|||
|
n2 |
15 |
-98 |
-94.8 |
-93 |
-91.8 |
-90.7 |
-84.1 |
-83.6 |
-81.5 |
||
|
30 |
-95.1 |
-93.1 |
-92 |
-90.8 |
-84.2 |
-83.7 |
-81.6 |
||||
|
60 |
-95.5 |
-93.4 |
-92.2 |
-90.9 |
-84.3 |
-83.8 |
-81.7 |
||||
|
n3 |
15 |
-97.0 |
-93.8 |
-92.0 |
-90.8 |
-89.7 |
-88.9 |
-86.2 |
-82.3 |
-81.3 |
-79.7 |
|
30 |
-94.1 |
-92.1 |
-91.0 |
-89.8 |
-89.0 |
-86.3 |
-82.4 |
-81.4 |
-79.8 |
||
|
60 |
-94.5 |
-92.4 |
-91.2 |
-90.0 |
-89.1 |
-86.4 |
-82.6 |
-81.5 |
-79.9 |
||
|
n5 |
15 |
-98.0 |
-94.8 |
-93.0 |
-86.8 |
-84.8 |
|||||
|
30 |
-95.1 |
-93.1 |
-88.6 |
-84.9 |
|||||||
|
n71 |
15 |
-98.0 |
-94.8 |
-93.0 |
-91.8 |
-90.7 |
-89.9 |
-89.2 |
-88.6 |
-81.5 |
|
|
30 |
-95.1 |
-93.1 |
-92.0 |
-90.8 |
-90.0 |
-89.3 |
-88.7 |
-81.5 |
|||
|
60 |
-95.5 |
-93.4 |
-92.2 |
-91.0 |
-90.1 |
-89.4 |
-88.9 |
-81.5 |
|||
|
n8 |
15 |
-97.0 |
-93.8 |
-91.4 |
-85.8 |
-78.4 |
|||||
|
30 |
-94.1 |
-91.7 |
-87.2 |
-78.5 |
|||||||
|
n12 |
15 |
-97.0 |
-93.8 |
-84.0 |
|||||||
|
30 |
-94.1 |
-84.1 |
|||||||||
|
n13 |
15 |
-97.0 |
-93.8 |
||||||||
|
30 |
-94.1 |
||||||||||
|
n14 |
15 |
-97.0 |
-93.8 |
||||||||
|
30 |
-94.1 |
||||||||||
|
n18 |
15 |
-100.0 |
-96.8 |
-95.0 |
|||||||
|
30 |
-97.1 |
-95.1 |
|||||||||
|
n20 |
15 |
-97.0 |
-93.8 |
-91.0 |
-89.8 |
||||||
|
30 |
-94.1 |
-91.1 |
-90.0 |
||||||||
|
n24 |
15 |
-100.0 |
-96.8 |
||||||||
|
30 |
-97.1 |
||||||||||
|
60 |
-97.5 |
||||||||||
|
n25 |
15 |
-96.5 |
-93.3 |
-91.5 |
-90.3 |
-89.3 |
-82.2 |
-81.7 |
-79.5 |
-77.6 |
|
|
30 |
-93.6 |
-91.6 |
-90.5 |
-89.4 |
-82.3 |
-81.8 |
-79.6 |
-77.7 |
|||
|
60 |
-94.0 |
-91.9 |
-90.7 |
-89.6 |
-82.4 |
-81.9 |
-79.7 |
-77.8 |
|||
|
n26 |
15 |
-97.56 |
-94.56 |
-92.76 |
-87.6 |
-84.5 |
-81.7 |
||||
|
30 |
-94.86 |
-92.76 |
-87.7 |
-84.6 |
-81.8 |
||||||
|
n28 |
15 |
-98.5 |
-95.5 |
-93.5 |
-90.8 |
-84.2 |
-78.5 |
||||
|
30 |
-95.6 |
-93.6 |
-91.0 |
-84.2 |
-78.6 |
||||||
|
n30 |
15 |
-99.0 |
-95.8 |
||||||||
|
30 |
-96.1 |
||||||||||
|
n65 |
15 |
-99.5 |
-96.3 |
-94.5 |
-93.3 |
-89.2 |
|||||
|
30 |
-96.6 |
-94.6 |
-93.5 |
-89.3 |
|||||||
|
60 |
-97.0 |
-94.9 |
-93.7 |
-89.4 |
|||||||
|
n66 |
15 |
-99.5 |
-96.3 |
-94.5 |
-93.3 |
-92.2 |
-91.4 |
-90.7 |
-90.1 |
-89.6 |
|
|
30 |
-96.6 |
-94.6 |
-93.5 |
-92.3 |
-91.5 |
-90.8 |
-90.2 |
-89.7 |
|||
|
60 |
-97.0 |
-94.9 |
-93.7 |
-92.5 |
-91.6 |
-90.9 |
-90.4 |
-89.8 |
|||
|
15 |
-100.0 |
-96.8 |
-95.0 |
-93.8 |
-92.7 |
||||||
|
n70 |
30 |
-97.1 |
-95.1 |
-94.0 |
-92.8 |
||||||
|
60 |
-97.5 |
-95.4 |
-94.2 |
-93.0 |
|||||||
|
n71 |
15 |
-97.2 |
-94.0 |
-91.6 |
-86.0 |
-84.1 |
-82.5 |
-80.7 |
|||
|
30 |
-94.3 |
-91.9 |
-87.4 |
-84.2 |
-82.6 |
-80.8 |
|||||
|
n74 |
15 |
-99.53 |
-96.33 |
-94.53 |
-89.33 |
||||||
|
30 |
-96.63 |
-94.63 |
-89.53 |
||||||||
|
60 |
-97.03 |
-94.93 |
-89.63 |
||||||||
|
n85 |
15 |
-97.0 |
-93.8 |
-84.0 |
|||||||
|
30 |
-94.1 |
-84.1 |
|||||||||
|
n100 |
15 |
-100 |
|||||||||
|
NOTE 1: Four Rx antenna ports shall be the baseline for this operating band except for two Rx vehicular UE. Four Rx antenna ports for RedCap UE is not supported for this operating band. NOTE 2: The transmitter shall be set to PUMAX as defined in clause 6.2.4 NOTE 3: The requirement is modified by -0.5 dB when the assigned NR channel bandwidth is confined within 1475.9 – 1510.9 MHz. NOTE 4: Void NOTE 5: Void NOTE 6: Values are modified by -0.5dB when carrier channel BW is between 865MHz and 894MHz. NOTE 7: Void. |
|||||||||||
Table 7.3.2-1b: Two antenna port reference sensitivity QPSK PREFSENS for TDD, SDL and FDD with variable duplex operation bands
|
Operating band / SCS / Channel bandwidth / REFSENS |
||||
|
Operating band |
SCS kHz |
Channel bandwidth (MHz) |
REFSENS (dBm)8 |
Duplex Mode |
|
n297 |
15 |
5,10 |
-97 + 10log10(NRB/25) |
SDL |
|
30 |
10 |
-94.1 + 10log10(NRB/24) |
||
|
n34 |
15 |
5, 10, 15 |
-100 + 10log10(NRB/25) |
TDD |
|
30 |
10, 15 |
-97.1 + 10log10(NRB/24) |
||
|
60 |
10, 15 |
-97.5 + 10log10(NRB/11) |
||
|
n381 |
15 |
5, 10, 15, 20, 25, 30, 40 |
-100 + 10log10(NRB/25) |
TDD |
|
30 |
10, 15, 20, 25, 30, 40 |
-97.1 + 10log10(NRB/24) |
||
|
60 |
10, 15, 20, 25, 30, 40 |
-97.5 + 10log10(NRB/11) |
||
|
n39 |
15 |
5, 10, 15, 20, 25, 30, 40 |
-100 + 10log10(NRB/25) |
TDD |
|
30 |
10, 15, 20, 25, 30, 40 |
-97.1 + 10log10(NRB/24) |
||
|
60 |
10, 15, 20, 25, 30, 40 |
-97.5 + 10log10(NRB/11) |
||
|
n40 |
15 |
5, 10, 15, 20, 25, 30, 40, 50 |
-100 + 10log10(NRB/25) |
TDD |
|
30 |
10, 15, 20, 25, 30, 40, 50, 60, 70, 80, 90, 100 |
-97.1 + 10log10(NRB/24) |
||
|
60 |
10, 15, 20, 25, 30, 40, 50, 60, 70, 80, 90, 100 |
-97.5 + 10log10(NRB/11) |
||
|
n411, n901 |
15 |
59, 10, 15, 20, 25, 30, 35, 40, 45, 50 |
-94.8 + 10log10(NRB/52) |
TDD |
|
30 |
10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100 |
-95.1 + 10log10(NRB/24) |
||
|
60 |
10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100 |
-95.5 + 10log10(NRB/11) |
||
|
n481 |
15 |
5, 10, 15, 20, 30, 40, 505 |
-99 + 10log10(NRB/25) |
TDD |
|
30 |
10, 15, 20, 30, 40, 505, 605, 705, 805, 905, 1005 |
-96.1 + 10log10(NRB/24) |
||
|
60 |
10, 15, 20, 30, 40, 505, 605, 705, 805, 905, 1005 |
-96.5 + 10log10(NRB/11) |
||
|
n50 |
15 |
5, 10, 15, 20, 30, 40, 50 |
-100 + 10log10(NRB/25) |
TDD |
|
30 |
10, 15, 20, 30, 40, 50, 60, 80 |
-97.1 + 10log10(NRB/24) |
||
|
60 |
10, 15, 20, 30, 40, 50, 60, 80 |
-97.5 + 10log10(NRB/11) |
||
|
n51 |
15 |
5 |
-100 |
TDD |
|
n53 |
15 |
5, 10 |
-100 + 10log10(NRB/25) |
TDD |
|
30 |
10 |
-97.1 |
||
|
60 |
10 |
-97.5 |
||
|
n677 |
15 |
5, 10, 15, 20 |
-100 + 10log10(NRB/25) |
SDL |
|
30 |
10, 15, 20 |
-97.1 + 10log10(NRB/24) |
||
|
n757 |
15 |
5,10,15,20,25,30,40,50 |
-100 + 10log10(NRB/25) |
SDL |
|
30 |
10,15,20,25,30,40,50 |
-97.1 + 10log10(NRB/24) |
||
|
60 |
10,15,20,25,30,40,50 |
-97.5 + 10log10(NRB/11) |
||
|
n767 |
15 |
5 |
-95.3 + 10log10(NRB/52) |
SDL |
|
n771,4 |
15 |
10, 15, 20, 25, 30, 40, 50 |
-95.3 + 10log10(NRB/52) |
TDD |
|
30 |
10, 15, 20, 25, 30, 40, 50, 60, 70, 80, 90, 100 |
-95.6 + 10log10(NRB/24) |
||
|
60 |
10, 15, 20, 25, 30, 40, 50, 60, 70, 80, 90, 100 |
-96.0 + 10log10(NRB/11) |
||
|
n781 |
15 |
10, 15, 20, 25, 30, 40, 50 |
-95.8 + 10log10(NRB/52) |
TDD |
|
30 |
10, 15, 20, 25, 30, 40, 50, 60, 70, 80, 90, 100 |
-96.1 + 10log10(NRB/24) |
||
|
60 |
10, 15, 20, 25, 30, 40, 50, 60, 70, 80, 90, 100 |
-96.5 + 10log10(NRB/11) |
||
|
n791 |
15 |
10, 20, 30, 40, 50 |
-95.8 + 10log10(NRB/52) |
TDD |
|
30 |
10, 20, 30, 40, 50, 60, 70, 80, 90, 100 |
-96.1 + 10log10(NRB/24) |
||
|
60 |
10, 20, 30, 40, 50, 60, 70, 80, 90, 100 |
-96.5 + 10log10(NRB/11) |
||
|
n91 |
15 |
5 |
-100 |
FDD |
|
n92 |
15 |
5,10,15,20 |
-100 + 10log10(NRB/25) |
FDD |
|
30 |
10,15,20 |
-97.1 + 10log10(NRB/24) |
||
|
n93 |
15 |
5 |
-100 |
FDD |
|
n94 |
15 |
5,10,15,20 |
-100 + 10log10(NRB/25) |
FDD |
|
30 |
10,15,20 |
-97.1 + 10log10(NRB/24) |
||
|
n101 |
15 |
5, 10 |
-100 + 10log10(NRB/25) |
TDD |
|
30 |
10 |
-97.1 + 10log10(NRB/24) |
||
|
n104 |
15 |
20, 30, 40, 50 |
-90.7 + 10log10(NRB/106) |
TDD |
|
30 |
20, 30, 40, 50, 60, 70, 80, 90, 100 |
-90.8 + 10log10(NRB/51) |
||
|
60 |
20, 30, 40, 50, 60, 70, 80, 90, 100 |
-91.1 + 10log10(NRB/24) |
||
|
NOTE 1: Four Rx antenna ports shall be the baseline for this operating band except for two Rx vehicular UE. Four Rx antenna ports for RedCap UE is not supported for this operating band. NOTE 2: The transmitter shall be set to PUMAX as defined in clause 6.2.4. NOTE 3: Void NOTE 4: The requirement is modified by -0.5 dB when the assigned UE channel bandwidth is confined within 3300 – 3800 MHz. NOTE 5: For these bandwidths, the minimum requirements are restricted to operation when carrier is configured as a downlink carrier part of CA configuration. NOTE 6: Void NOTE 7: For SDL bands, the reference sensitivity requirements shall be verified by inter-band CA combinations with SDL band, which are supported by UE. NOTE 8: The REFSENS value is rounded to the nearest number down to one decimal point. “NRB” in REFSENS formula is the maximum transmission bandwidth configuration as defined in Table 5.3.2-1. NOTE 9: 5 MHz only applies to n90, not n41 |
||||
For power class 2 UEs, certain degradation of the reference sensitivity in Table 7.3.2-1a is allowed. The maximum amount of degradation is specified in Table 7.3.2-1c, and in Table 7.3.2-1d for a UE that indicates txDiversity-r16 [15].
Table 7.3.2-1c Reference Sensitivity Degradation from PC3 to PC2 for FDD bands for UE not supporting Tx Diversity
|
Operating Band |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
25 MHz |
30 MHz (dB) |
35 MHz (dB) |
40 MHz |
45 MHz (dB) |
50 MHz |
|---|---|---|---|---|---|---|---|---|---|---|
|
n1 |
0 |
0 |
0 |
0 |
0 |
0 |
– |
0 |
0 |
0 |
|
n3 |
0.5 |
0.5 |
0.5 |
0.5 |
0.6 |
0.8 |
1.1 |
1.5 |
2.3 |
2.8 |
|
NOTE 1: The transmitter shall be set to PUMAX as defined in clause 6.2.4 |
||||||||||
Table 7.3.2-1d Reference Sensitivity Degradation from PC3 to PC2 for FDD bands for UE supporting Tx Diversity
|
Operating Band |
5 MHz |
10 MHz |
15 MHz |
20 MHz |
25 MHz |
30 MHz (dB) |
35 MHz (dB) |
40 MHz |
45 MHz (dB) |
50 MHz |
|---|---|---|---|---|---|---|---|---|---|---|
|
n1 |
0 |
0 |
0 |
0 |
0 |
0 |
– |
0 |
0 |
0 |
|
n3 |
1.4 |
1.5 |
1.5 |
1.5 |
1.6 |
1.7 |
2.8 |
5 |
5.5 |
6.0 |
|
NOTE 1: The transmitter shall be set to PUMAX as defined in clause 6.2G.4 |
||||||||||
For UE(s) equipped with 4 Rx antenna ports, reference sensitivity for 2Rx antenna ports in Table 7.3.2-1a and in Table 7.3.2-1b shall be modified by the amount given in ΔRIB,4R in Table 7.3.2-2 for the applicable operating bands.
Table 7.3.2-2: Four antenna port reference sensitivity allowance ΔRIB,4R
|
Operating band |
ΔRIB,4R (dB) |
|
n8, n28, n71 |
-2.71 |
|
n1, n2, n3, n30, n40, n7, n34, n38, n39, n41, n66, n70 |
-2.7 |
|
n48, n77, n78, n79, n104 |
-2.2 |
|
NOTE 1: 4 Rx operation is targeted for FWA form factor |
|
The reference receive sensitivity (REFSENS) requirement specified in Table 7.3.2-1a, Table 7.3.2-1b, Table 7.3.2-1c, Table 7.3.2-1d and Table 7.3.2-2 shall be met with uplink transmission bandwidth less than or equal to that specified in Table 7.3.2-3.
Table 7.3.2-3: Uplink configuration for reference sensitivity
|
Operating band / SCS (kHz) / Channel bandwidth (MHz) / Duplex mode |
|||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Operating Band |
SCS |
5 |
10 |
15 |
20 |
25 |
30 |
35 |
40 |
45 |
50 |
60 |
70 |
80 |
90 |
100 |
Duplex Mode |
|
n1 |
15 |
25 |
501 |
751 |
1001 |
1281 |
1281 |
1281 |
1281 |
1281 |
FDD |
||||||
|
30 |
24 |
361 |
501 |
641 |
641 |
641 |
641 |
641 |
|||||||||
|
60 |
101 |
18 |
24 |
301 |
301 |
301 |
301 |
301 |
|||||||||
|
n2 |
15 |
25 |
501 |
501 |
501 |
501 |
481 |
401 |
401 |
FDD |
|||||||
|
30 |
101 |
24 |
241 |
241 |
241 |
241 |
201 |
201 |
|||||||||
|
60 |
101 |
101 |
101 |
101 |
101 |
101 |
101 |
||||||||||
|
n3 |
15 |
25 |
501 |
501 |
501 |
501 |
501 |
501 |
501 |
501 |
501 |
FDD |
|||||
|
30 |
24 |
241 |
241 |
241 |
241 |
241 |
241 |
241 |
241 |
||||||||
|
60 |
101 |
101 |
101 |
101 |
101 |
101 |
101 |
101 |
101 |
||||||||
|
n5 |
15 |
25 |
251 |
201 |
201 |
Note 5 |
FDD |
||||||||||
|
30 |
121 |
101 |
101 |
Note 5 |
|||||||||||||
|
n7 |
15 |
25 |
501 |
751 |
751 |
721 |
641 |
451 |
451 |
451 |
FDD |
||||||
|
30 |
24 |
361 |
361 |
361 |
321 |
201 |
201 |
201 |
|||||||||
|
60 |
101 |
18 |
181 |
181 |
161 |
101 |
101 |
101 |
|||||||||
|
n8 |
15 |
25 |
251 |
201 |
201 |
Note 5 |
FDD |
||||||||||
|
30 |
121 |
101 |
101 |
Note 5 |
|||||||||||||
|
n12 |
15 |
201 |
201 |
201 |
FDD |
||||||||||||
|
30 |
101 |
101 |
|||||||||||||||
|
n13 |
15 |
201 |
201 |
FDD |
|||||||||||||
|
30 |
101 |
||||||||||||||||
|
n14 |
15 |
201 |
201 |
FDD |
|||||||||||||
|
30 |
101 |
||||||||||||||||
|
n18 |
15 |
25 |
251 |
251 |
FDD |
||||||||||||
|
30 |
101 |
101 |
|||||||||||||||
|
n20 |
15 |
25 |
201 |
202 |
202 |
FDD |
|||||||||||
|
30 |
101 |
102 |
102 |
||||||||||||||
|
n24 |
15 |
25 |
50 |
FDD |
|||||||||||||
|
30 |
24 |
||||||||||||||||
|
60 |
10 |
||||||||||||||||
|
n25 |
15 |
25 |
501 |
501 |
501 |
501 |
481 |
401 |
401 |
Note 5 |
FDD |
||||||
|
30 |
24 |
241 |
241 |
241 |
241 |
201 |
201 |
Note 5 |
|||||||||
|
60 |
101 |
101 |
101 |
101 |
101 |
101 |
101 |
Note 5 |
|||||||||
|
n26 |
15 |
25 |
251 |
251 |
251 |
Note 5 |
Note 5 |
FDD |
|||||||||
|
30 |
121 |
121 |
121 |
Note 5 |
Note 5 |
||||||||||||
|
n28 |
15 |
25 |
251 |
251 |
251 |
251 |
251 |
FDD |
|||||||||
|
30 |
101 |
101 |
101 |
101 |
101 |
||||||||||||
|
n30 |
15 |
201 |
201 |
FDD |
|||||||||||||
|
30 |
101 |
||||||||||||||||
|
n34 |
15 |
25 |
50 |
75 |
TDD |
||||||||||||
|
30 |
24 |
36 |
|||||||||||||||
|
60 |
10 |
18 |
|||||||||||||||
|
n38 |
15 |
25 |
50 |
75 |
100 |
128 |
160 |
216 |
TDD |
||||||||
|
30 |
24 |
36 |
50 |
64 |
75 |
100 |
|||||||||||
|
60 |
10 |
18 |
24 |
30 |
36 |
50 |
|||||||||||
|
n39 |
15 |
25 |
50 |
75 |
100 |
128 |
160 |
216 |
TDD |
||||||||
|
30 |
24 |
36 |
50 |
64 |
75 |
100 |
|||||||||||
|
60 |
10 |
18 |
24 |
30 |
36 |
50 |
|||||||||||
|
n40 |
15 |
25 |
50 |
75 |
100 |
128 |
160 |
216 |
270 |
TDD |
|||||||
|
30 |
24 |
36 |
50 |
64 |
75 |
100 |
128 |
162 |
180 |
216 |
243 |
270 |
|||||
|
60 |
10 |
18 |
24 |
30 |
36 |
50 |
64 |
75 |
90 |
100 |
120 |
135 |
|||||
|
n41, n90 |
15 |
256 |
50 |
75 |
100 |
128 |
160 |
180 |
216 |
240 |
270 |
TDD |
|||||
|
30 |
24 |
36 |
50 |
64 |
75 |
90 |
100 |
108 |
128 |
162 |
180 |
216 |
243 |
270 |
|||
|
60 |
10 |
18 |
24 |
30 |
36 |
40 |
50 |
54 |
64 |
75 |
90 |
100 |
120 |
135 |
|||
|
n48 |
15 |
25 |
50 |
75 |
100 |
160 |
216 |
TDD |
|||||||||
|
30 |
24 |
36 |
50 |
75 |
100 |
||||||||||||
|
60 |
10 |
18 |
24 |
36 |
50 |
||||||||||||
|
n50 |
15 |
25 |
50 |
75 |
100 |
160 |
216 |
270 |
TDD |
||||||||
|
30 |
24 |
36 |
50 |
75 |
100 |
128 |
162 |
Note 3 |
|||||||||
|
60 |
10 |
18 |
24 |
36 |
50 |
64 |
75 |
Note 3 |
|||||||||
|
n51 |
15 |
25 |
TDD |
||||||||||||||
|
n53 |
15 |
25 |
50 |
TDD |
|||||||||||||
|
30 |
24 |
||||||||||||||||
|
60 |
10 |
||||||||||||||||
|
n65 |
15 |
25 |
501 |
751 |
1001 |
1281 |
FDD |
||||||||||
|
30 |
24 |
361 |
501 |
641 |
|||||||||||||
|
60 |
101 |
18 |
24 |
301 |
|||||||||||||
|
n66 |
15 |
25 |
501 |
751 |
1001 |
1281 |
160 |
1801 |
216 |
[2401] |
FDD |
||||||
|
30 |
24 |
361 |
501 |
641 |
751 |
901 |
1001 |
[1081] |
|||||||||
|
60 |
101 |
18 |
24 |
301 |
361 |
401 |
501 |
[541] |
|||||||||
|
n70 |
15 |
25 |
501 |
751 |
Note 3 |
Note 3 |
FDD |
||||||||||
|
30 |
24 |
361 |
Note 3 |
Note 3 |
|||||||||||||
|
60 |
101 |
18 |
Note 3 |
Note 3 |
|||||||||||||
|
n71 |
15 |
25 |
251 |
201 |
201 |
Note 5 |
Note 5 |
Note 5 |
FDD |
||||||||
|
30 |
121 |
101 |
101 |
Note 5 |
Note 5 |
Note 5 |
|||||||||||
|
n74 |
15 |
25 |
251 |
251 |
251 |
FDD |
|||||||||||
|
30 |
101 |
101 |
101 |
||||||||||||||
|
60 |
51 |
51 |
51 |
||||||||||||||
|
n77 |
15 |
50 |
75 |
100 |
128 |
160 |
216 |
270 |
TDD |
||||||||
|
30 |
24 |
36 |
50 |
64 |
75 |
100 |
128 |
162 |
180 |
216 |
243 |
270 |
|||||
|
60 |
10 |
18 |
24 |
30 |
36 |
50 |
64 |
75 |
90 |
100 |
120 |
135 |
|||||
|
n78 |
15 |
50 |
75 |
100 |
128 |
160 |
216 |
270 |
TDD |
||||||||
|
30 |
24 |
36 |
50 |
64 |
75 |
100 |
128 |
162 |
180 |
216 |
243 |
270 |
|||||
|
60 |
10 |
18 |
24 |
30 |
36 |
50 |
64 |
75 |
90 |
100 |
120 |
135 |
|||||
|
n79 |
15 |
50 |
100 |
160 |
216 |
270 |
TDD |
||||||||||
|
30 |
24 |
50 |
75 |
100 |
128 |
162 |
180 |
216 |
243 |
270 |
|||||||
|
60 |
10 |
24 |
36 |
50 |
64 |
75 |
90 |
100 |
120 |
135 |
|||||||
|
n85 |
15 |
201 |
201 |
201 |
FDD |
||||||||||||
|
30 |
101 |
101 |
|||||||||||||||
|
n91 |
15 |
254 |
201,4 |
FDD |
|||||||||||||
|
n92 |
15 |
25 |
201 |
201 |
201 |
FDD |
|||||||||||
|
30 |
101 |
101 |
101 |
||||||||||||||
|
n93 |
15 |
254 |
251,4 |
FDD |
|||||||||||||
|
n94 |
15 |
25 |
251 |
201 |
201 |
FDD |
|||||||||||
|
30 |
121 |
101 |
101 |
||||||||||||||
|
n100 |
15 |
25 |
FDD |
||||||||||||||
|
n101 |
15 |
25 |
50 |
TDD |
|||||||||||||
|
30 |
24 |
||||||||||||||||
|
n104 |
15 |
100 |
216 |
270 |
TDD |
||||||||||||
|
30 |
50 |
100 |
128 |
162 |
180 |
216 |
243 |
270 |
|||||||||
|
60 |
24 |
50 |
64 |
75 |
90 |
100 |
120 |
135 |
|||||||||
|
Note 1: UL resource blocks shall be located as close as possible to the downlink operating band but confined within the transmission bandwidth configuration for the channel bandwidth (Table 5.3.2-1). Note 2: For Band 20; for 15 kHz SCS, in the case of 15 MHz channel bandwidth, the UL resource blocks shall be located at RBstart 11 and in the case of 20 MHz channel bandwidth, the UL resource blocks shall be located at RBstart 16; for 30 kHz SCS, in the case of 15 MHz channel bandwidth, the UL resource blocks shall be located at RBstart 6 and in the case of 20 MHz channel bandwidth, the UL resource blocks shall be located at RBstart 8; for 60 kHz SCS, in the case of 15 MHz channel bandwidth, the UL resource blocks shall be located at RBstart 3 and in the case of 20 MHz channel bandwidth, the UL resource blocks shall be located at RBstart 4; Note 3: For DL channel bandwidths that do not have symmetric UL channel bandwidth, highest valid UL configuration with lowest TX-RX separation (Table 5.4.4-1) shall be used unless otherwise specified. Note 4: For band n91 and n93, largest supported UL bandwidth configuration shall be used. Note 5: For this DL channel bandwidth, the UL configuration of the highest UL channel bandwidth specified in Table 5.3.6-1 and the default Tx-Rx frequency separation specified in Table 5.4.4-1 shall be used. Note 6: 5 MHz only applies to n90, not n41 |
|||||||||||||||||
Unless given by Table 7.3.2-4, the minimum requirements specified in Tables 7.3.2-1a, Tables 7.3.2-1b, Tables 7.3.2-1c, Tables 7.3.2-1d and 7.3.2-2 shall be verified with the network signalling value NS_01 (Table 6.2.3-1) configured.
Table 7.3.2-4: Network signaling value for reference sensitivity
|
Operating band |
Network Signalling value |
|
n2 |
NS_03 |
|
n12 |
NS_06 |
|
n13 |
NS_06 |
|
n14 |
NS_06 |
|
n24 |
NS_56 |
|
n25 |
NS_03 |
|
n30 |
NS_21 |
|
n48 |
NS_27 |
|
n53 |
NS_45 |
|
n66 |
NS_03 |
|
n70 |
NS_03 |
|
n71 |
NS_35 |
|
n85 |
NS_06 |
7.3.3 ΔRIB,c
For a UE supporting CA, SUL or DC band combination, the minimum requirement for reference sensitivity in Table 7.3.2-1a and Table 7.3.2-1b shall be increased by the amount given by ΔRIB,c defined in clause 7.3A, 7.3B, 7.3C in this specification and 7.3A, 7.3B in TS 38.101-3 [3] for the applicable operating bands.
In case the UE supports more than one of band combinations for CA, SUL or DC, and an operating band belongs to more than one band combinations then
– When the operating band frequency range is ≤ 1 GHz, the applicable additional ΔRIB,c shall be the average value for all band combinations defined in clause 7.3A, 7.3B, 7.3C in this specification and 7.3A, 7.3B in TS 38.101-3 [3], truncated to one decimal place that apply for that operating band among the supported band combinations. In case there is a harmonic relation between low band UL and high band DL, then the maximum ΔRIB,c among the different supported band combinations involving such band shall be applied
– When the operating band frequency range is > 1 GHz, the applicable additional ΔRIB,c shall be the maximum value for all band combinations defined in clause 7.3A, 7.3B, 7.3C in this specification and 7.3A, 7.3B in TS 38.101-3 [3] for the applicable operating bands.