6.2E Transmitter power for V2X

38.101-13GPPNRPart 1: Range 1 StandaloneRelease 17TSUser Equipment (UE) radio transmission and reception

6.2E.1 UE maximum output power for V2X

6.2E.1.1 General

When NR V2X UE is configured for NR V2X sidelink transmissions non-concurrent with NR uplink transmissions for NR V2X operating bands specified in Table 5.2E.1-1, the allowed NR V2X UE maximum output power is specified in Table 6.2E.1.1-0.

Table 6.2E.1.1-0: NR V2X UE Power Class

NR band

Class 1 (dBm)

Tolerance (dB)

Class 2 (dBm)

Tolerance (dB)

Class 3 (dBm)

Tolerance (dB)

n14

31

+2/-3

23

±2

n38

23

±2

n47

26

+2/-3

23

±2

n79

23

+2/-3

When a UE is configured for NR V2X sidelink transmissions in NR Band n47, the V2X UE shall meet the following additional requirements for transmission within the frequency ranges 5855-5925 MHz:

– The maximum mean power spectral density shall be restricted to 23 dBm/MHz EIRP when the network signaling value NS_33 is indicated.

where the network signaling values are specified in clause 6.2E.3.

NOTE: The PSD limit in EIRP shall be converted to conducted requirement depend on the supported post antenna connector gain Gpost connector declared by the UE following the principle described in annex I in [11].

For NR V2X UE supporting SL MIMO or Tx diversity, the maximum output power requirements in Table 6.2E.1.1-1 is defined as the sum of the maximum output power from each UE antenna connector. The period of measurement shall be at least one sub frame (1 ms). For UE supporting SL MIMO, the requirements shall be met with the SL MIMO configurations specified in Table 6.2D.1-2.

Table 6.2E.1.1-1: NR V2X UE Power Class for SL-MIMO

NR band

Class 1 (dBm)

Tolerance (dB)

Class 2 (dBm)

Tolerance (dB)

Class 3 (dBm)

Tolerance (dB)

Class 4 (dBm)

Tolerance (dB)

n38

23

+2/-3

n47

26

+2/-3

23

+2/-3

n79

23

+2/-3

If the UE transmits on one antenna connector at a time, the requirements in Table 6.2E.1.1-0 shall apply to the active antenna connector.

6.2E.1.2 UE maximum output power for V2X con-current operation

For the inter-band NR V2X con-current operation, the maximum output power is specified in Table 6.2E.1.2-1 for each operating band. The period of measurement shall be at least one sub frame (1ms).

Table 6.2E.1.2-1: Power Class for NR V2X inter-band con-current combination (two bands)

NR V2X con-current operating band Configuration

NR band

Class 1 (dBm)

Tolerance (dB)

Class 2 (dBm)

Tolerance

(dB)

Class 3 (dBm)

Tolerance (dB)

Class 4 (dBm)

Tolerance (dB)

V2X_n1A-n47A

n1

23

±2

n47

23

+2/-3

V2X_n5A-n47A

n5

23

±2

n47

23

+2/-3

V2X_n8A-n47A

n8

23

±24

n47

23

+2/-3

V2X_n39A-n47A

n39

23

+2/-3

n47

23

+2/-3

V2X_n40A-n47A

n40

23

+2/-3

n47

23

+2/-3

V2X_n41A-n47A

n41

23

+2/-3

n47

23

+2/-3

V2X_n71A-n47A

n71

23

+2/-34

n47

23

+2/-3

V2X_n78A-n47A

n78

23

+2/-3

n47

23

+2/-3

V2X_n79A-n47A

n79

23

+2/-3

n47

23

+2/-3

NOTE 1: For the con-current band combinations, the simultaneous transmission and reception of sidelink and Uu interfaces can be supported while operation is agnostic of the service used on each interface.

NOTE 2: PPowerClass is the maximum output power specified without taking into account the tolerance for each operating band.

NOTE 3: For inter-band con-current operation, the aggregation power apply to the total transmitted power over all component carriers (per UE).

NOTE 4: 4 refers to the transmission bandwidths (Figure 5.6-1) confined within FUL_low and FUL_low + 4 MHz or FUL_high – 4 MHz and FUL_high, the maximum output power requirement is relaxed by reducing the lower tolerance limit by 1.5 dB

For the intra-band con-current NR V2X operation, the maximum output power is specified in Table 6.2E.1.2-2. The period of measurement shall be at least one sub frame (1ms).

Table 6.2E.1.2-2: NR V2X UE Power Class for intra-band con-current combination

NR V2X con-current operating band Configuration

Class 1 (dBm)

Tolerance (dB)

Class 2 (dBm)

Tolerance

(dB)

Class 3 (dBm)

Tolerance (dB)

Class 4 (dBm)

Tolerance (dB)

V2X_n79B

26

+2/-32

23

+2/-32

NOTE 1: Void.

NOTE 2: PPowerClass is the maximum UE power specified without taking into account the tolerance

NOTE 3: For intra-band con-current aggregation the maximum power requirement apply to the total transmitted power over all component carriers (per UE).

NOTE 4: Power Class 3 is the default power class unless otherwise stated.

6.2E.2 UE maximum output power reduction for V2X

6.2E.2.1 General

When UE is configured for NR V2X sidelink transmissions non-concurrent with NR uplink transmissions for NR V2X operating bands specified in Table 5.2E.1-1, this clause specifies the allowed Maximum Power Reduction (MPR) power for V2X physical channels and signals due to PSCCH/PSSCH, PSFCH and S-SSB transmission.

6.2E.2.2 MPR for Power class 2 and Power class 3 V2X UE

For contiguous allocation of PSCCH and PSSCH simultaneous transmission, the allowed MPR for the maximum output power for NR V2X physical channels PSCCH and PSSCH shall be as specified in Table 6.2E.2.2-1 for Power class 3 NR V2X UE and Table 6.2E.2.2-2 for power class 2 NR V2X UE.

Table 6.2E.2.2-1: Maximum Power Reduction (MPR) for power class 3 NR V2X

Modulation

Channel bandwidth/MPR (dB)

Outer RB allocations

Inner RB allocations

CP-OFDM

QPSK

≤ 4.5

≤ 2.5

16QAM

≤ 4.5

≤ 2.5

64 QAM

≤ 4.5

256 QAM

≤ 7.0

Table 6.2E.2.2-2: Maximum Power Reduction (MPR) for power class 2 NR V2X

Modulation

Channel bandwidth/MPR (dB)

Outer RB allocations

Inner RB allocations

QPSK

≤ 5.5

≤ 2.5

CP-OFDM

16QAM

64 QAM

≤ 6

≤ 4.5

256 QAM

≤ 7.0

For NR V2X UE supporting SL MIMO or Tx diversity, the allowed MPR for the maximum output power for NR V2X physical channels PSCCH and PSSCH are specified in Table 6.2E.2.2-3 for power class 2 UE.

Table 6.2E.2.2-3: Maximum Power Reduction (MPR) for power class 2 NR V2X with dual Tx

Modulation

Channel bandwidth/MPR (dB)

Outer RB allocations

Inner RB allocations

CP-OFDM

QPSK

≤ 6.0

≤ 3.0

16QAM

64 QAM

≤ 7.0

≤ 5.5

256 QAM

≤ 9.0

Where the following parameters are defined to specify valid RB allocation ranges for Outer and Inner RB allocations:

NRB is the maximum number of RBs for a given Channel bandwidth and sub-carrier spacing defined in Table 5.3.2-1.

RBStart,Low = max(1, floor(LCRB/2))

where max() indicates the largest value of all arguments and floor(x) is the greatest integer less than or equal to x.

RBStart,High = NRB – RBStart,Low – LCRB

The RB allocation is an Inner RB allocation if the following conditions are met

RBStart,Low ≤ RBStart ≤ RBStart,High, and

LCRB ≤ ceil(NRB/2)

where ceil(x) is the smallest integer greater than or equal to x.

The RB allocation is an Outer RB allocation for all other allocations which are not an Inner RB allocation.

For PSFCH with single RB transmission for PC3 NR V2X UE, the required MPR is defined as follow

MPR_PSFCH = 3.5 dB

For contiguous and non-contiguous allocation for simultaneous PSFCH transmission for PC3 NR V2X UE, the required MPR are specified as follow

MPR_PSFCH = CEIL {MA_PSFCH, 0.5}

Where MA_PSFCH for power class 3 is defined as follows

MA_PSFCH = 7.5 ; 0.00< NGap/NRB ≤ 0.55

= 12.0 ; 0.55< NGap/NRB ≤1.0

For PSFCH with single RB transmission for PC2 NR V2X UE, the required MPR is defined as follow

MPR_PSFCH = 4.5 dB

For contiguous and non-contiguous allocation for simultaneous PSFCH transmission for PC2 NR V2X UE, the required MPR are specified as follow

MPR_PSFCH = CEIL {MA_PSFCH, 0.5}

Where MA is defined as follows

Where MA_PSFCH for power class 2 is defined as follows

MA_PSFCH = 8.5 ; 0.00 ≤ NGap/NRB < 0.4

= 10.0 ; 0.4 ≤ NGap/NRB < 0.55

= 14.0 ; 0.55 ≤ NGap/NRB ≤ 1.0

Where,

NGap is the gap RB amount between RBstart and RBend for contiguous and non-contiguous allocation simultaneous PSFCH transmission. (NGap = RBend – RBstart)

CEIL{MA, 0.5} means rounding upwards to closest 0.5dB.

The allowed MPR for the maximum output power for NR V2X physical channels on S-SSB transmission shall be specified in Table 6.2E.2.2-2 for power class 3 and power class 2.

Table 6.2E.2.2-2: Maximum Power Reduction (MPR) for S-SSB transmission for power class 3 and power class 2 NR V2X

Channel

MPRS-SSB (dB)

Outer RB allocations

Inner RB allocations

S-SSB

≤ 6.0

≤ 2.5

For NR V2X UE with two transmit antenna connectors, the allowed Maximum Power Reduction (MPR) values specified in clause 6.2E.2 for PC3 and PC2 shall apply to the maximum output power specified in Table 6.2E.1.1-1. For UE supporting SL MIMO, the requirements shall be met with SL MIMO configurations defined in Table 6.2D.1-2. For UE supporting SL MIMO or Tx diversity, the maximum output power is defined as the sum of the maximum output power from each UE antenna connector.

For the UE maximum output power modified by MPR, the power limits specified in clause 6.2E.4 apply.

6.2E.2.3 MPR for Power class 2 and Power class 3 V2X con-current operation

For the inter-band con-current NR V2X operation, the allowed maximum power reduction (MPR) for the maximum output power shall be applied per each component carrier. The MPR requirements in clause 6.2.2 apply for NR Uu operation in licensed band, and the MPR requirements in clause 6.2E.2 apply for NR sidelink operation in licensed band or Band n47.

For the intra-band con-current NR V2X operation with contiguous RB allocation, the allowed maximum power reduction (MPR) for NR V2X physical channels PSCCH and PSSCH shall be as specified in Table 6.2E.2.3-1 for Power class 3 V2X con-current UE.

Table 6.2E.2.3-1: MPR for contiguous RB allocation for power class 3 NR V2X con-current UE

Higher Modulation order between Sidelink and Uplink

MPR for bandwidth class B(dB)

Inner RB allocation

Outer RB allocation

CP-OFDM

QPSK

≤ 2.5

≤ 4.5

16QAM

≤ 2.5

≤ 4.5

64QAM

≤ 4.5

≤ 5.0

256QAM

≤ 6.0

≤ 6.0

For bandwidth class B with contiguous RB allocation, the following parameters are defined to specify valid RB allocation ranges for Inner and Outer RB allocations:

An RB allocation is contiguous if LCRB1 = 0 or LCRB2 = 0 or (LCRB1 ≠ 0 and LCRB2 ≠ 0 and RBStart1 + LCRB1 = NRB1 and RBStart2 = 0), where RBStart1, LCRB1, and NRB1 are for SL CC1, RBStart2, LCRB2, and NRB2 are for UL CC2. SL CC1 is the component carrier with lower frequency.

In contiguous NR V2X intra-band con-current operation, a contiguous allocation is an inner allocation if

RBStart,Low ≤ RBStart_SL&UL ≤ RBStart,High, and NRB_alloc ≤ ceil(NRB,agg /2),

where

RBStart,Low = max(1, floor(NRB_alloc /2))

RBStart,High = NRB,agg – RBStart,Low – NRB,alloc,

with

NRB_alloc= LCRB1 ∙ 2µ1 + LCRB2 ∙ 2µ2

NRB_alloc= (NRB1 – RBStart1)∙ 2µ1 + (RBStart2 + LCRB2 ) ∙ 2µ2,

NRB,agg=NRB1∙2µ1+ NRB2∙2µ2.

If LCRB1 =0, RBStart_SL&UL = NRB1∙2µ1+ RBStart2∙2µ2,

if LCRB1 > 0, RBStart_SL&UL = RBStart1∙2µ1.

Where, µ1 and µ2 is 0, 1 and 2 for SCS of 15kHz, 30kHz and 60kHz respectively.

A contiguous allocation that is not an Inner contiguous allocation is an Outer contiguous allocation.

For the intra-band con-current NR V2X operation with non-contiguous RB allocation, the allowed maximum power reduction (MPR) for NR V2X physical channels PSCCH and PSSCH shall be as specified in Table 6.2E.2.3-2 for Power class 3 V2X con-current UE.

Table 6.2E.2.3-2: MPR for non-contiguous RB allocation for power class 3 NR V2X con-current UE

Higher Modulation order between Sidelink and Uplink

MPR for bandwidth class B(dB)

Inner RB allocation

Outer1 RB allocation

Outer2 RB allocation

CP-OFDM

QPSK

≤ 2.5

≤ 4.0

≤ 4.5

16QAM

≤ 2.5

≤ 4.0

≤ 4.5

64QAM

≤ 4.5

≤ 4.5

≤ 5.0

256QAM

≤ 6.0

≤ 6.0

≤ 6.0

For bandwidth classes B with non-contiguous RB allocation, the following parameters are defined to specify valid RB allocation ranges for Inner, Outer1 and Outer2 RB allocations:

Non-Contiguous RB allocation is defined as RBStart1 + LCRB1 < NRB1, or RBStart2 > 0, when both SL CC and UL CC are activated and allocated with RB(s), where RBStart1, LCRB1, and NRB1 are for SL CC1, RBStart2, LCRB2, and NRB2 are for UL CC2. SL CC1 is the component carrier with lower frequency.

In contiguous NR V2X intra-band con-current operation, a non-contiguous RB allocation is a non-contiguous Inner RB allocation if the following conditions are met:

RBStart,Low ≤ RBStart_CA ≤ RBStart,High and NRB_alloc ≤ ceil((BWChannel_SL&UL / 3 – BWgap ) / 0.18MHz),

where

NRB_alloc = (NRB1 – RBStart1)∙ 2µ1 + (RBStart2 + LCRB2 ) ∙ 2µ2, RBStart_SL&UL = RBStart1∙2μ1

RBStart,Low = max(1, floor(NRB_alloc + (BWgap – BWGB,low)/0.18MHz))

RBStart,High = floor((BWChannel_SL&UL – 2 ∙ BWgap – BWGB,low)/0.18MHz – 2 ∙ NRB_alloc)

BWGB,low =Foffset,low – (NRB1∙12+1)∙SCS1/2

BWgap is the bandwidth of the gap between NRB1 and NRB2 possible allocations of SL CC1 and UL CC2 respectively.

In contiguous NR V2X intra-band con-current operation, a non-contiguous RB allocation is a non-contiguous outer 1 RB allocation if the following conditions are met:

RBStart,Low ≤ RBStart_SL&UL ≤ RBStart,High and NRB_alloc ≤ ceil((3 BWChannel_SL&UL / 5 – BWgap) / 0.18MHz)

where

RBStart,Low = max(1, 2 ∙ NRB_alloc – floor( (BWChannel_SL&UL – 2 ∙ BWgap + BWGB,low)/0.18MHz)),

RBStart,High = floor((2 ∙ BWChannel_SL&UL – 3 ∙ BWgap – BWGB,low) / 0.18MHz – 3 ∙ NRB_alloc)

NRB_alloc , RBStart_SL&UL , BWgap and BWGB,low are as defined for the Inner region.

In contiguous NR V2X intra-band con-current operation, a non-contiguous allocation is an Outer 2 allocation if it is neither a non-contiguous Inner allocation nor an Outer 1 allocation.

For PSFCH with single RB transmission for PC3 NR V2X intra-band con-current UE, the required MPR is specified in clause 6.2E.2.2 shall be applied.

For the allowed MPR for S-SSB transmission for PC3 NR V2X intra-band con-current UE, the required MPR is specified in clasue 6.2E.2.2 shall be applied.

For the intra-band con-current NR V2X operation with contiguous RB allocation in contiguous carrier, the allowed maximum power reduction (MPR) for NR V2X physical channels PSCCH and PSSCH shall be as specified in Table 6.2E.2.3-3 for Power class 2 V2X con-current UE.

Table 6.2E.2.3-3: MPR for contiguous RB allocation for power class 2 NR V2X con-current UE

Higher Modulation order between Sidelink and Uplink

MPR for bandwidth class B(dB)

Inner RB allocation

Outer RB allocation

CP-OFDM

QPSK

≤ 3.0

≤ 5.5

16QAM

≤ 4.0

≤ 5.5

64QAM

≤ 5.5

≤ 6.0

256QAM

≤ 7.5

≤ 7.5

For the intra-band con-current NR V2X operation with non-contiguous RB allocation in contiguous carrier, the allowed maximum power reduction (MPR) for NR V2X physical channels PSCCH and PSSCH shall be as specified in Table 6.2E.2.3-4 for Power class 2 V2X con-current UE.

Table 6.2E.2.3-4: MPR for non-contiguous RB allocation for power class 2 NR V2X con-current UE

Higher Modulation order between Sidelink and Uplink

MPR for bandwidth class B(dB)

Inner RB allocation

Outer1 RB allocation

Outer2 RB allocation

CP-OFDM

QPSK

≤ 3.0

≤ 5.5

≤ 6.0

16QAM

≤ 4.5

≤ 5.5

≤ 6.5

64QAM

≤ 5.5

≤ 6.5

≤ 7.0

256QAM

≤ 8.0

≤ 8.0

≤ 8.0

The parameters in clause 6.2E.2.3 are considered to determine MPR values according to RB allocation.

For PSFCH with single RB transmission for PC2 NR V2X intra-band con-current UE, the required MPR is specified in clause 6.2E.2.2 shall be applied.

For the allowed MPR for S-SSB transmission for PC2 NR V2X intra-band con-current UE, the required MPR is specified in clause 6.2E.2.2 shall be applied.

6.2E.2.4 MPR for Power class 1 UE in Band n14

For NR Public Safety (PS) UE with contiguous allocation of PSCCH and PSSCH simultaneous transmission, the allowed NR PS UE maximum output power reduction for power class 1 UE shall meet the NR V2X MPR values specified in Table 6.2E.2.2-1 of clause 6.2E.2.2.

For NR Public Safety (PS) UE of single or multiple PSFCH simultaneous transmission, the allowed NR PS UE maximum output power reduction for power class 1 UE shall meet the NR V2X MPR values for PC3 UE’s PSFCH transmission in clause 6.2E.2.2.

For NR Public Safety (PS) UE of S-SSB transmission, the allowed NR PS UE maximum output power reduction for power class 1 UE shall meet the NR V2X MPR values specified in Table 6.2E.2.2-2 of clause 6.2E.2.2.

6.2E.3 UE additional maximum output power reduction for V2X

6.2E.3.1 General

For the applied maximum output power reduction is obtained by taking the maximum value of MPR requirements specified in clause 6.2E.2 and A-MPR requirements specified in current clause.

Additional emission requirements can be indicated by the network or pre-configured radio parameters. Each additional emission requirement is associated with a unique network signalling (NS) value indicated in RRC signalling by an NR frequency band number of the applicable operating band and an associated value in the field [additionalSpectrumEmission]. Throughout this specification, the notion of indication or signalling of an NS value refers to the corresponding indication of an NR V2X frequency band number of the applicable operating band, the IE field [freqBandIndicatorNR] and an associated value of [additionalSpectrumEmission] in the relevant RRC information elements [7].

To meet the additional requirements, additional maximum power reduction (A-MPR) is allowed for the maximum output power as specified in Table 6.2.1-1. Outer and inner allocation notation used in clause 6.2E.3 is defined in clause 6.2E.2. In absence of modulation and waveform types the A-MPR applies to all modulation and waveform types.

Table 6.2E.3.1-1: Additional Maximum Power Reduction (A-MPR) for PC3 NR V2X

Network Signalling value

Requirements (clause)

NR Band

Channel bandwidth (MHz)

Resources Blocks (NRB)

A-MPR (dB)

NS_01

Table 5.2E.1-1

10, 20, 30, 40

Table 5.3.2-1

N/A

NS_06

6.5.2.3.4 (A-SEM)

n14

5, 10

Table 5.3.2-1

N/A

NS_33

6.5E.2.3.1 (A-SEM)

6.5E.3.4 (A-SE)

n47

10

Clause 6.2E.3.2

NS_52

6.5E.2.3.2 (A-SEM)

n47

40

Clause 6.2E.3.3

Table 6.2E.3.1-2: Mapping of network signaling label

NR V2X operating bands

Value of additionalSpectrumEmission

0

1

2

3

4

5

6

7

n142

NS_01

NS_06

n38

NS_01

n47

NS_01

NS_33

NS_52

NOTE 1: [additionalSpectrumEmission] corresponds to an information element of the same name defined in clause 6.3.2 of TS 38.331 [7].

NOTE 2: For the NR PS UE in n14, same A-MPR shall be applied for PC1 PS UE since PC1 PS UE for Band n14 is not targeted for smartphone form factor.

For UE with two transmit antenna connectors, the A-MPR values specified in clause 6.2E.3.2 and 6.2E.3.3 shall apply to the maximum output power specified in Table 6.2E.1.1-1. The requirements shall be met with the SL MIMO configurations specified in Table 6.2D.1-2. For UE supporting SL MIMO or Tx Diversity, the maximum output power is defined as the sum of the maximum output power from each UE antenna connector. Unless stated otherwise, an A-MPR of 0 dB shall be used.

For the UE maximum output power modified by A-MPR, the power limits specified in clause 6.2E.4 apply.

6.2E.3.2 A-MPR for V2X UE by NS_33

When NS_33 is indicated by the network or pre-configured radio parameters for NR V2X UE, the additional maximum output power reduction specified as

A-MPR = CEIL {MA, 0.5}

Where MA is defined as follows

MA = A-MPRBase + Gpost connector* A-MPRStep

CEIL{MA, 0.5} means rounding upwards to closest 0.5dB.

A-MPRBase and A-MPRStep are specified in Tables 6.2E.3.2-1, 6.2E.3.2-2 is allowed when network signalling value is provided. A-MPRBase is the default A-MPR value when no Gpost connector is declared. The supported post antenna connector gain Gpost connector is declared by the UE following the principle described in annex I in [11]. The A-MPRstep is the increase in A-MPR allowance to allow UE to meet tighter conducted A-SE and A-SEM requirements with higher value of declared Gpost connector.

For the contiguous PSSCH and PSCCH transmission when NS_33 is indicated by the network or pre-configured radio parameters for NR V2X UE, the NR UE allow the follow A-MPR requirements specified in Table 6.2E.3.2-1 and 6.2E.3.2-2 for power class 3. And A-MPR requirements specified in Table 6.2E.3.2-2a and 6.2E.3.2-2b for power class 2 are allowed for NR V2X UE.

Table 6.2E.3.2-1: PC3 A-MPR for PSSCH/PSCCH by NS_33 (at Fc =5860MHz)

Carrier frequency [MHz]

Resources Blocks (LCRB)

Start Resource

Block

A-MPRBase (dB)

QPSK/16QAM

64QAM

256QAM

5860

≥ 10 and ≤ 15

0

≤ 24

≥ 1 and ≤ 3

≤19

≥ 10 and ≤ 15

≥ 26 and ≤ 38

≤6

≥ 10 and ≤ 15

≥38

≤ 6

≥ 10 and ≤ 20

≥ 12 and ≤ 14

≤11

≥ 15 and ≤ 19

≤9.5

≥ 20 and ≤ 25

≤8.0

> 15 and < 25

≥ 25

≤ 8

≥ 10 and < 40

≥ 4 and ≤7

≤ 16

≥ 8 and ≤ 11

≤ 13.5

≥ 20 and < 40

≥ 0 and ≤ 3

≤ 22

≥ 25 and < 40

≥ 16 and ≤ 21

≤ 9.5

≥ 22 and ≤ 27

≤ 8.0

≥ 24 and ≤ 40

≥ 12 and ≤ 15

≤ 12

40 and 45

0 and 1

≤ 19

≥ 2 and ≤ 5

≤ 16

≥ 6 and ≤ 11

≤ 13.5

>45

≥ 0

≤ 16

NOTE 1: A-MPRstep =1.2 dB is applied for RBstart 0 and 1 and A-MPRstep =0.7 dB is applied for all other RBstart

NOTE 2: Applicable for Channel Bandwidth = 10 MHz

Table 6.2E.3.2-2: PC3 A-MPR for PSSCH/PSCCH by NS_33 (at other carrier frequency)

Carrier frequency [MHz]

RB allocations

A-MPRBase (dB)

A-MPRstep (dB)

QPSK

16QAM

64QAM

256QAM

5870, 5880, 5890, 5900, 5910, 5920

Inner

≤ 3.0

≤ 5.0

≤ 6.0

0.5

Outer

≤ 4.5

NOTE 1: Inner and Outer RB allocations are defined in clause 6.2E.2.2

NOTE 2: Applicable for Channel Bandwidth = 10 MHz

Table 6.2E.3.2-2a: PC2 A-MPR for PSCCH/PSSCH by NS_33 (at Fc=5860MHz)

Carrier frequency [MHz]

Resource Block (LCRB)

Start Resource Block

A-MPR(dB)

QPSK/16QAM

64QAM

256QAM

5860

≥ 10 and ≤ 15

0 and 1

≤ 24

2 and 3

≤ 22

4

≤ 20

≥ 10 and ≤ 25

≥ 5 and ≤ 7

≤ 17.5

≥ 10 and ≤ 30

10

≤ 16

≥ 10

8 and 9

≤ 16

≥ 11 and ≤ 14

≤ 14.5

≥ 15 and ≤ 19

≤ 13

≥ 20 and ≤ 24

≤ 11.5

≥ 25 and ≤ 29

≤ 10

≥ 30

≤ 8.5

≥ 20 and ≤ 24

1

≤ 22

≥ 20 and ≤ 30

0

≤ 22

2 and 3

≤ 20

4

≤ 17.5

≥ 25 and ≤ 40

1

≤ 20

≥ 30

≥ 5 and ≤ 7

≤ 16

≥ 36

0

≤ 20

≥ 2 and ≤ 4

≤ 17.5

10

≤ 14.5

≥ 45

1

≤ 17.5

NOTE 1: A-MPRstep =1.2 dB is applied for RBstart 0 and 1 and A-MPRstep =0.7 dB is applied for all other RBstart

NOTE 2: Applicable for Channel Bandwidth = 10 MHz

Table 6.2E.3.2-2b: PC2 A-MPR for PSSCH/PSCCH by NS_33 (at other carrier frequency)

Carrier frequency [MHz]

RB allocations

A-MPR (dB)

QPSK

16QAM

64QAM

256QAM

5870,5910,5920

outer

≤ 8.5

≤ 8.5

inner

≤ 6.0

5880,5890,5900

outer

≤ 6.0

≤ 6.5

inner

≤ 3.5

≤ 4.5

NOTE 1: Inner and Outer RB allocations are defined in clause 6.2E.2.1

NOTE 2: Applicable for Channel Bandwidth = 10 MHz

For the simultaneous PSFCH transmission when NS_33 is indicated by the network or pre-configured radio parameters for NR V2X UE, the NR UE allow the follow A-MPR requirements specified in Table 6.2E.3.2-3 for power class 3 and in Table 6.2E.3.2-3a for power class 2.

Table 6.2E.3.2-3: PC3 A-MPR for simultaneous PSFCH by NS_33

Channel Bandwidth

[MHz]

Center Frequency

[MHz]

RB allocation

A-MPRBase (dB)

A-MPRstep (dB)

0 ≤ NGap / NRB < 0.15

0.15≤ NGap / NRB < 0.3

0.3≤ NGap / NRB ≤ 1

10

5860

NRB =1

19.0

1.0

NRB > 1

22.0

5870, 5880, 5890, 5900, 5910, 5920

NRB =1

5

0.8

NRB > 1

14

7

18.5

Note 1: NGap is the gap RB amount between RBstart and RBend for contiguous and non-contiguous allocation simultaneous PSFCH transmission. (NGap = RBend – RBstart)

Table 6.2E.3.2-3a: PC2 A-MPR for simultaneous PSFCH by NS_33

Channel Bandwidth

[MHz]

Center Frequency

[MHz]

RB allocation

A-MPRBase (dB)

A-MPRstep (dB)

0 ≤ NGap / NRB < 0.2

0.2≤ NGap / NRB < 0.4

0.4≤ NGap / NRB ≤ 1

10

5860

NRB =1

25.0

1.0

NRB > 1

22.0

5870, 5880, 5890, 5900, 5910, 5920

NRB =1

5

0.8

NRB > 1

16.5

12

20

Note 1: NGap is the gap RB amount between RBstart and RBend for contiguous and non-contiguous allocation simultaneous PSFCH transmission. (NGap = RBend – RBstart)

For the S-SSB transmission when NS_33 is indicated by the network or pre-configured radio parameters for NR V2X UE, the NR UE allow the follow A-MPR requirements specified in Table 6.2E.3.2-4 for power class 3 and in Table 6.2E.3.2-5 for power class 2.

Table 6.2E.3.2-4: PC3 A-MPR for S-SSB transmission by NS_33

Carrier Frequency (MHz)

RBStart * 12*SCS

[MHz]

A-MPRBase (dB)

AMPRStep (dB)

5860

≤1.0

≤ 25

0.6

>1.0 and ≤2.0

≤ 19

>2.0 and ≤3.24

≤ 12

>3.24 and ≤3.6

≤ 10

>3.6

≤ 9

5870, 5880, 5890, 5900, 5910, 5920

≤1.0

≤ 7.0

0.85

>1.0 and ≤1.6

≤ 6.5

>1.6 and ≤2.6

≤ 5.8

>2.6 and ≤3.24

≤ 4.5

>3.24 and ≤4.32

≤ 5.5

>4.32

≤ 6.5

Table 6.2E.3.2-5: PC2 A-MPR for S-SSB transmission by NS_33

Carrier Frequency (MHz)

RBStart * 12*SCS

[MHz]

A-MPRBase (dB)

AMPRStep (dB)

5860

≤1.0

≤ 25

0.6

>1.0 and ≤2.0

≤ 19

>2.0 and ≤3.24

≤ 12

>3.24 and ≤3.6

≤ 10

>3.6

≤ 14

5870, 5880, 5890, 5900, 5910, 5920

≤1.0

≤ 7.0

0.85

>1.0 and ≤1.6

≤ 6.5

>1.6 and ≤2.6

≤ 5.8

>2.6 and ≤3.24

≤ 4.5

>3.24 and ≤4.32

≤ 5.5

>4.32

≤ 6.5

6.2E.3.3 A-MPR for Power class 3 V2X UE by NS_52

When NS_52 is indicated by the network or pre-configured radio parameters for NR V2X UE, the additional maximum output power reduction specified as

A-MPR = CEIL {MA, 0.5}

Where MA is defined as follows

MA = A-MPR

CEIL{MA, 0.5} means rounding upwards to closest 0.5dB.

For the contiguous PSSCH and PSCCH transmission when NS_52 is indicated by the network or pre-configured radio parameters for NR V2X UE, the NR UE allow the follow A-MPR requirements.

Table 6.2E.3.3-1: A-MPR for PSSCH/PSCCH by NS_52

Carrier frequency(MHz)

Modulation

A-MPR(dB)

Region 1

Region 2

Region 3

5885

QPSK

≤ 15

≤ 8.0

≤ 5.5

16QAM

≤ 8.0

≤ 5.5

64QAM

≤ 8.5

≤ 5.5

256QAM

≤ 8.5

≤ 6.0

Note1: Void.

Where the following parameters are defined to specify valid RB allocation ranges for Region1, Region2 and Region3 according to RB allocations:

Table 6.2E.3.3-1a: A-MPR Region definitions for PSSCH/PSCCH by NS_52

Channel Bandwidth, MHz

Carrier frequency (MHz)

A-MPR parameters for region definitions

A-MPR

RBstart or RBend

LCRB

40

5885

RBstart ≤ floor(NRB*0.2) or RBend ≥ NRB – floor(NRB*0.2)

LCRB ≤floor(NRB*0.2)

Region 1

The RB allocation is in Region 2 allocation for all other allocations which are not a Region1 or Region3 allocation.

Region 2

floor(NRB /3.5) ≤ RBstart ≤ NRB –floor(NRB /3.5) – LCRB

LCRB ≤ceil(NRB/3.5)

Region 3

NRB is the maximum number of RBs for a given Channel bandwidth and sub-carrier spacing defined in Table 5.3.2-1 [3].

For the simultaneous PSFCH transmission when NS_52 is indicated by the network or pre-configured radio parameters for NR V2X UE, the NR UE allow the follow A-MPR requirements

Table 6.2E.3.3-2: A-MPR for simultaneous PSFCH by NS_52

Channel Bandwidth [MHz]

Carrier frequency [MHz]

A-MPR (dB)

40 MHz

5885

23.5

For the S-SSB transmission when NS_52 is indicated by the network or pre-configured radio parameters for NR V2X UE, the NR UE allow the follow A-MPR requirements

Table 6.2E.3.2-3: A-MPR for S-SSB transmission by NS_52

Carrier Frequency [MHz]

RBStart * 12*SCS

[MHz]

A-MPR (dB)

5885

≤ 7

≤ 16

> 7 and ≤ 12

≤ 10.5

> 12 and ≤ 19

≤ 4.0

> 19 and ≤ 25

≤ 10.5

> 25

≤ 16

6.2E.3.4 A-MPR for V2X con-current operation

For the inter-band con-current NR V2X operation, the allowed additional maximum power reduction (A-MPR) for the maximum output power shall be applied per each component carrier. The A-MPR requirements in clause 6.2.3 apply for NR Uu operation in licensed band, and the A-MPR requirements in clause 6.2E.3.2 and 6.2E.3.3 apply for NR sidelink operation in Band n47.

For the intra-band con-current NR V2X operation, the A-MPR requirements in [6.2E.3.4] apply for NR Uu and SL con-current operation in the licensed band.

6.2E.4 Configured transmitted power for V2X

6.2E.4.1 General

The NR V2X UE is allowed to set its configured maximum output power PCMAX,f,c for carrier f of serving cell c in each slot. The configured maximum output power PCMAX,f,c is set within the following bounds:

PCMAX_L,f,c ≤ PCMAX,f,c ≤ PCMAX_H,f,c with

PCMAX_L,f, c = MIN {PEMAX,c, PPowerClass, V2X – MAX(MAX(MPRc , A-MPRc) + TIB,c , P-MPRc), PRegulatory,c }

PCMAX_H,f, c = MIN {PEMAX,c, PPowerClass, V2X, PRegulatory,c }

where

– PCMAX,f,c is configured for PSSCH\PSCCH, S-SSB and PSFCH, respectively;

– For the total transmitted power PCMAX,PSSCH/PSCCH, PEMAX,c is the value given by IE sl-maxTransPower, defined by TS 38.331

– For the total transmitted power PCMAX,S-SSB, the PCMAX_L,f,c and PCMAX_H,f,c are defined as follows:

PCMAX_L,f,c = MIN {PPowerClass, V2X – MAX(MAX(MPRc , A-MPRc) + TIB,c , P-MPRc), PRegulatory,c}

PCMAX_H,f,c = MIN {PPowerClass, V2X, PRegulatory,c}

– For the total transmitted power PCMAX,PSFCH, PEMAX,c is the value given by IE sl-maxTransPower when single resource pool configured is transmitted at a given time and [sum of] the IEs sl-maxTransPower when multiple resource pools configured are transmitted at a given time, defined by TS 38.331.

– PPowerClass,V2X is the maximum UE power specified in Table 6.2E.1.1-1 without taking into account the tolerance specified in the Table 6.2E.1.1-1;

– MPRc and A-MPRc for serving cell c are specified in clause 6.2E.2 and clause 6.2E.3 for PSSCH\PSCCH, S-SSB and PSFCH, respectively;

– TIB,c, and P-MPRc are specified in clause 6.2.4

– PRegulatory,c= 10 – Gpost connector dBm the V2X UE is within the protected zone [12] of CEN DSRC tolling system and operating in Band n47; PRegulatory,c= 33 – Gpost connector dBm otherwise.

The maximum output power PCMAX,PSSCH and PCMAX,PSCCH are derived from PCMAX,c based on 0dB PSD offset between PSSCH and PSCCH.

For the measured configured maximum output power PUMAX,c for NR V2X sidelink transmissions non-concurrent with NR uplink transmissions, the same requirement as in clause 6.2.4 shall be applied.

For NR V2X UE supporting SL MIMO or Tx Diversity, the transmitted power is configured per each UE.

For NR V2X UE with two transmit antenna connectors at the same time, the tolerance is specified in Table 6.2E.4.1-1. The requirements shall be met with SL MIMO configurations specified in Table 6.2D.1-2.

Table 6.2E.4.1-1: PCMAX,c tolerance schemes for MIMO

PCMAX,c
(dBm)

Tolerance
TLOW(PCMAX_L,c) (dB)

Tolerance
THIGH(PCMAX_H,c) (dB)

PCMAX,c = 26

3.0

2.0

23 ≤ PCMAX,c < 26

3.0

2.0

22 ≤ PCMAX,c < 23

5.0

2.0

21 ≤ PCMAX,c < 22

5.0

3.0

20 ≤ PCMAX,c < 21

6.0

4.0

16 ≤ PCMAX,c < 20

5.0

11 ≤ PCMAX,c < 16

6.0

-40 ≤ PCMAX,c < 11

7.0

6.2E.4.2 Configured transmitted power for inter-band V2X con-current operation

When a UE is configured for simultaneous NR V2X sidelink and NR uplink transmissions for inter-band con-current operation, the UE is allowed to set its configured maximum output power PCMAX,c,NR and PCMAX,c,V2X for the configured NR uplink carrier and the configured NR V2X carrier, respectively, and its total configured maximum output power PCMAX,c.

The configured maximum output power PCMAX c,NR(p) in slot p for the configured NR uplink carrier shall be set within the bounds:

PCMAX_L,c,NR (p) ≤ PCMAX,c,NR (p) ≤ PCMAX_H,c,NR (p)

where PCMAX_L,c,NR and PCMAX_H,c,NR are the limit as specified in clause 6.2E.4.1.

The configured maximum output power PCMAX c,V2X (q) in slot q for the configured NR V2X carrier shall be set within the bounds:

PCMAX,c,V2X (q) ≤ PCMAX_H,c,V2X (q)

where PCMAX_H,c,V2X is the limit as specified in clause 6.2E.4.

The total UE configured maximum output power PCMAX (p,q) in a slot p of NR uplink carrier and a slot q of NR V2X sidelink that overlap in time shall be set within the following bounds for synchronous and asynchronous operation unless stated otherwise:

PCMAX_L (p,q) ≤ PCMAX (p,q) ≤ PCMAX_H (p,q)

with

PCMAX_L (p,q) = PCMAX_L,c,NR (p)

PCMAX_H (p,q) = 10 log10 [pCMAX_H,c,NR (p) + pCMAX_H,c,V2X (q)]

where pCMAX_H,c,V2X and pCMAX_H,c,NR are the limits PCMAX_H,c,V2X (q) and PCMAX_H,c,NR (p) expressed in linear scale.

The measured total maximum output power PUMAX over both the NR uplink and NR V2X carriers is

PUMAX = 10 log10 [pUMAX,c,NR + pUMAX,c,V2X],

where pUMAX,c,NR denotes the measured output power of serving cell c for the configured NR uplink carrier, and pUMAX,c,V2X denotes the measured output power for the configured NR V2X carrier expressed in linear scale.

When a UE is configured for synchronous V2X sidelink and uplink transmissions,

PCMAX_L(p, q) – TLOW (PCMAX_L(p, q)) ≤ PUMAX ≤ PCMAX_H(p, q) + THIGH (PCMAX_H(p, q))

where PCMAX_L (p,q) and PCMAX_H (p,q) are the limits for the pair (p,q) and with the tolerances TLOW(PCMAX) and THIGH(PCMAX) for applicable values of PCMAX specified in Table 6.2E.4.1-1.. PCMAX_L may be modified for any overlapping portion of slots (p, q) and (p +1, q+1).

6.2E.4.3 Configured transmitted power for intra-band V2X con-current operation

For intra-band con-current operation, if transmission of Uu and SL does not overlap in time, the configured output power PCMAX,c specified in clause 6.2E.4.1 and 6.2.4 apply for SL and Uu transmission respectively; otherwise, if transmission of Uu and SL overlap in time, the configured maximum output power PCMAX,c on serving cell c for SL and Uu shall be set as specified in clause 6.2E.4.1 and in clause 6.2.4, but with MPRc = MPR and A-MPRc = A-MPR with MPR and A-MPR as determined by subclause 6.2E.2.3 for both PC3 and PC2 and subclause 6.2E.3.4, respectively. There is one power management term for the UE, denoted P-MPR, and P-MPR c = P-MPR.

The total configured maximum output power PCMAX shall be set within the following bounds:

PCMAX_L ≤ PCMAX ≤ PCMAX_H

For intra-band concurrent operation when same slot pattern is used in all aggregated serving cells,

PCMAX_L = MIN{10 log10 ∑ pEMAX,c – TC , PPowerClass,con-current – MAX(MAX(MPR, A-MPR) + ΔTIB,c + TC, P-MPR ) }

PCMAX_H = MIN{10 log10 ∑ pEMAX,c , PPowerClass,con-current}

where

– pEMAX,c is the linear value of PEMAX,c which is given by IE P-Max for Uu serving cell c or by IE sl-MaxTransPower for SL defined in [7];

– PPowerClass,con-current is the maximum UE power specified in Table 6.2E.1.2-2 without taking into account the tolerance;

– MPR and A-MPR are specified in clause 6.2E.2 and 6.2E.3, respectively;

– TIB,c is the additional tolerance for serving cell c as specified in clause 6.2E.4.3

– P-MPR is the power management term for the UE;

– TC is the highest value TC,c among all serving cells c;

For intra-band concurrent operation, when at least one different numerology/slot pattern is used in aggregated cells, the UE is allowed to set its configured maximum output power PCMAX,c(i),i for serving cell c(i) of slot numerology type i, and its total configured maximum output power PCMAX.

The configured maximum output power PCMAX,c(i),i (p) in slot p of serving cell c(i) on slot numerology type i shall be set within the following bounds:

PCMAX_L,f,c(i),i (p) ≤ PCMAX,f,c(i), i (p) ≤ PCMAX_H,f,c(i),i (p)

where PCMAX_L,f,c (i),i (p) and PCMAX_H,f,c(i),i (p) are the limits for a serving cell c(i) of slot numerology type i as specified in clause 6.2.4.

The total UE configured maximum output power PCMAX (p,q) in a slot p of slot numerology or symbol pattern i, and a slot q of slot numerology or symbol pattern j that overlap in time shall be set within the following bounds unless stated otherwise:

PCMAX_L(p,q) ≤ PCMAX (p,q) ≤ PCMAX_H (p,q)

When slots p and q have different transmissions lengths and belong to different cells on same band for intra-band operation:

PCMAX_L (p,q) = MIN {10 log10 [pCMAX_L,f,c(i),Uu,i (p) + pCMAX_L,f,c(i),V2X,j (q)], PPowerClass,con-current}

PCMAX_H (p,q) = MIN {10 log10 [pCMAX_ H,f,c(i), Uu,,i (p) + pCMAX_ H,f,c(i),V2X,j (q)], PPowerClass,con-current}

where pCMAX_L,f,c (i),Uu,i and pCMAX_ H,f,c(i),Uu,i are the respective limits PCMAX_L,f,c (i),Uu,i and PCMAX_H,f,c(i),Uu,i expressed in linear scale.

TREF and Teval are specified in Table 6.2E.4.3-1 when same and different slot patterns are used in aggregated carriers. For each TREF, the PCMAX_L is evaluated per Teval and given by the minimum value taken over the transmission(s) within the Teval; the minimum PCMAX_L over the one or more Teval is then applied for the entire TREF. PPowerClass,Concurrent shall not be exceeded by the UE during any period of time.

Table 6.2E.4.3-1: PCMAX evaluation window for different slot and channel durations

TREF

Teval

Teval with frequency hopping

TREF of largest slot duration over both UL and SL CCs

Physical channel length

Min(Tno_hopping, Physical Channel Length)

The measured maximum output power PUMAX over all serving cells with same slot pattern shall be within the following range:

PCMAX_L – MAX{TL, TLOW(PCMAX_L) } ≤ PUMAX ≤ PCMAX_H + THIGH(PCMAX_H)

PUMAX = 10 log10 ∑ pUMAX,c

where pUMAX,c denotes the measured maximum output power for serving cell c expressed in linear scale. The tolerances TLOW(PCMAX) and THIGH(PCMAX) for applicable values of PCMAX are specified in Table 6.2E.4.3-2. The tolerance TL is the absolute value of the lower tolerance for applicable NRV2X concurrent operation configuration as specified in Table 6.2 E.1.2-2 for intra-band NR V2X concurrent operation.

The measured maximum output power PUMAX over all serving cells, when at least one slot has a different transmission numerology or slot pattern, shall be within the following range:

P’CMAX_L– MAX{TL, TLOW (P’CMAX_L)} ≤ P’UMAX ≤ P’CMAX_H + THIGH (P’CMAX_H)

P’UMAX = 10 log10 ∑ p’UMAX,c

where p’UMAX,c denotes the average measured maximum output power for serving cell c expressed in linear scale over TREF. The tolerances TLOW(P’CMAX) and THIGH(P’CMAX) for applicable values of P’CMAX are specified in Table 6.2E.4.3-2. The tolerance TL is the absolute value of the lower tolerance for applicable NR V2X concurrent operation configuration as specified in Table 6.2E.1.2-2 for intra-band NR V2X concurrent operation.

where:

P’CMAX_L = MIN{ MIN {10log10∑( pCMAX_L,f,c(i),i), PPowerClass,concurrent} over all overlapping slots in TREF}

P’CMAX_H = MAX{ MIN{10 log10 ∑ pEMAX,c , PPowerClass,concurrent} over all overlapping slots in TREF}

Table 6.2E.4.3-2: PCMAX tolerance for SL intra-band con-current operation

PCMAX
(dBm)

Tolerance
TLOW(PCMAX)
(dB)

Tolerance
THIGH(PCMAX)
(dB)

26 ≤ PCMAX < 23

3

2

21 ≤ PCMAX ≤ 23

2.0

20 ≤ PCMAX < 21

2.5

19 ≤ PCMAX < 20

3.5

18 ≤ PCMAX < 19

4.0

13 ≤ PCMAX < 18

5.0

8 ≤ PCMAX < 13

6.0

-40 ≤ PCMAX < 8

7.0

A UE supporting sidelink operation can be configured by higher layers with one or more sidelink resource pools. A sidelink resource pool can be associated with either sidelink resource allocation mode 1 or sidelink resource allocation mode 2.

For sidelink resource allocation in either mode 1 or mode 2, if UE is in RRC_CONNECTED state, and the preparation procedure time for transmission of sidelink physical channel is available before of PUSCH preparation procedure time, for transmission of Uu and SL not overlap in time, the configured output power PCMAX,c specified in clause 6.2E.4.1 and in clause 6.2.4 apply for SL and Uu transmission respectively, otherwise, the configured maximum output power PCMAX specified in this clause shall apply.

For sidelink resource allocation mode 2, if UE is in RRC_IDLE state, sidelink transmission is based on pre-configured sidelink resource pool, the UE configured output power is determined by sidelink only, where the configured output power specified in clause 6.2E.4.1 apply.

For sidelink resource allocation mode 2, if UE is in RRC_INACTIVE state, and Uu does not support SDT, the configured output power specified in clause 6.2E.4.1 apply, otherwise, the configured maximum output power PCMAX in this clause shall apply.