5 Applicability of Requirements

37.145-23GPPActive Antenna System (AAS) Base Station (BS) conformance testingPart 2: radiated conformance testingRelease 17TS

5.1 General

The present clause defines for each radiated test requirement the set of mandatory test configurations which shall be used for demonstrating conformance for radiated requirement.

Test configurations for beams supporting multiple RAT in the tested operating band are specified in clause 5.1.

Test configurations for radiated requirements where the operating band has been declared to support single RAT requirements (see table 4.10-1, D9.5) by either MSR requirements for UTRA only or E-UTRA only or with a single-RAT UTRA requirements or single RAT E-UTRA requirements are specified in subclause 5.2.

Test configurations for an AAS BS with operating bands which have multi-band dependencies are specified in subclause 5.3.

Requirements apply to AAS BS according to the declared RAT radiated Capability Set (see table 4.10-1, D9.25) within each supported operating band the Band Category of the declared operating band (see table 4.10-1, D9.4), as listed in the heading of each table. Some RF requirements listed in the tables may not be mandatory or they may apply only regionally. This is further specified for each requirement in clauses 6 and 7, and in table 4.4-1.

For a declared RAT radiated Capability Set (see table 4.10-1, D9.25) in tables 5.2-1, 5.3.2-1, 5.3.3-1, 5.3.4-1, 5.4.1-1 or 5.4.2-1 only the requirements listed in the column for that radiated Capability Set apply. Requirements listed under RCSA other than the declared RCSA(s) need not be tested. In case the BS is declared to support more than one CS, the tests that are common between different supported CSs are not repeated.

An AAS BS where the operating band is declared: to support multiple RATs (MSR) and to be capable of contiguous spectrum operation only, the test configuration(s) in tables 5.2-1 and 5.3.2-1 denoted by a "C" and entries that refer to single-RAT specifications shall be used for testing.

An AAS BS where the operating band is declared: to support multiple RATs (MSR), to be capable of contiguous and non-contiguous spectrum operation (see table 4.10-1, D9.28), where the parameters according to clause 4.10 are identical for contiguous and non-contiguous operation (see table 4.10-1, D9.29). Shall use for each declared operating band the test configuration(s) in tables 5.2-1 and 5.3.2-1 denoted by "CNC" and entries that refer to single-RAT specifications shall be used.

An AAS BS where the operating band is declared: to support multiple RATs (MSR), to be capable of contiguous and non-contiguous spectrum operation (see table 4.10-1, D9.28), where the parameters according to clause 4.10 are not identical for contiguous and non-contiguous operation (see table 4.10-1, D9.29). Shall use for each declared operating band the test configuration(s) in tables 5.2-1 and 5.3.2-1 denoted by "C/NC" and entries that refer to single-RAT specifications shall be used.

For an AAS BS operating bands which have multi-band dependencies which is MSR capable the applicability of the requirement for each operating band is determined by the RAT configuration within that operating band as identified in tables 5.2-1 and 5.3.2-1, unless otherwise stated. The testing of an AAS BS in operating bands with multi-band dependencies which are MSR capable shall be according to table 5.4.1-1 as follows:

– For requirements test denoted by SBT (Single Band Test), the test configuration (s) in tables 5.2-1 and 5.3.2-1 shall be used for each operating band depending on the RAT configuration within that band.

– For requirements test denoted by MBT (Multi-Band Test), the test configuration (s) in table 5.4.1-1 shall be used depending on the Band Category of the declared operating band combination.

For a single–RAT UTRA only operating bands clause 5.3.3 defines for each radiated test requirement the set of mandatory test configurations which shall be used for demonstrating conformance. The applicable test configurations are specified in table 5.3.3-1 for each supported RF configuration, which shall be declared according to clause 4.10. The generation and EIRP allocation for each test configuration is defined in clause 4.11.2.

For a single-RAT E-UTRA only operating bands clause 5.3.4 defines for each radiated test requirement the set of mandatory test configurations which shall be used for demonstrating conformance. The applicable test configurations are specified in table 5.3.4-1 for each supported RF configuration, which shall be declared according to clause 4.10. The generation and EIRP allocation for each test configuration is defined in clause 4.11.3.

For an AAS BS operating band declared to be capable of single carrier operation only (see table 4.10-1, D9.4), a single carrier (SC) shall be used for testing.

In Table 5.1-1, the requirement applicability for each requirement set is defined. For each requirement, the applicable requirement clause in the specification is identified. Requirements not included in a requirement set is marked not applicable (NA).

Table 5.1-1: Requirement set applicability

Requirement

Requirement set

Hybrid requirements set

OTA requirements set

Radiated transmit power

6.2

6.2

OTA Base Station output power

6.3

OTA Output power dynamics

6.4

OTA Transmit ON/OFF power

6.5

OTA Transmitted signal quality

6.6

OTA occupied bandwidth

NA

6.7.2

OTA ACLR

6.7.3

OTA Spectrum emission mask

6.7.4

OTA Operating band unwanted emission

6.7.5

OTA transmitter spurious emission

6.7.6

OTA transmitter intermodulation

6.8

OTA sensitivity

7.2

7.2

OTA reference sensitivity level

7.3

OTA dynamic range

7.4

OTA in-band selectivity and blocking

7.5

OTA out-of-band blocking

7.6

OTA receiver spurious emission

NA

7.7

OTA receiver intermodulation

7.8

OTA in-channel selectivity

7.9

Radiated performance requirements

8

5.2 Test configurations for AAS BS for operating bands where MSR with more than 1 RAT is supported

Table 5.2-1: Test configuration applicability to requirements
and capability sets for AAS BS supporting MSR operation

Test case

UTRA + E-UTRA (RCSA 3)

E-UTRA + NR (RCSA 3A)

UTRA + E-UTRA + NR (RCSA 3B)

BC1

BC2

BC3

BC1

BC2

BC3

BC1, BC2

6.2

Radiated transmit power

C: ATCR3a

CNC: ATCR3a C/NC: ATCR3a, ANTCR3 

C: ATCR3a

CNC: ATCR3a C/NC: ATCR3a, ANTCR3

C: ATCR3b

C: ATCR7

CNC: ATCR7

C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ATCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ATCR7 C/NC: ATCR7, ANTCR7

C: ATCR9

CNC: ATCR9

C/NC: ATCR9, ANTCR9

6.3

OTA Base Station output power

–

–

–

–

–

–

–

6.3.2

OTA Maximum output power

C: ATCR3a CNC: ATCR3a C/NC: ATCR3a, ANTCR3 

C: ATCR3a CNC: ATCR3a C/NC: ATCR3a, ANTCR3

N/A

C: ATCR7 CNC: ATCR7 C/NC: ATCR7, ANTCR7 

C: ATCR7

CNC: ATCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ATCR7 C/NC: ATCR7, ANTCR7

C: ATCR9

CNC: ATCR9

C/NC: ATCR9, ANTCR9

6.3.3

OTA E-UTRA DL RS power

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Subclause 5.3.4

6.4

OTA Output power dynamics

–

–

–

–

–

–

–

 

E-UTRA

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Subclause 5.3.4

 

UTRA FDD

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

Subclause 5.3.3

NR – RE power control dynamic range

N/A

N/A

N/A

Tested with Error Vector Magnitude

Tested with Error Vector Magnitude

Tested with Error Vector Magnitude

Tested with Error Vector Magnitude

NR – total power dynamic range

N/A

N/A

N/A

SC

SC

SC

SC

6.5

OTA Transmit ON/OFF power

–

–

–

–

–

–

–

6.5.1

OTA Transmitter OFF power

N/A

N/A

N/A

N/A

N/A

C: ATCR7

CNC: ATCR7 C/NC: ATCR7, ANTCR7

N/A

6.5.2

OTA Transmitter transient period

N/A

N/A

N/A

N/A

N/A

C: ATCR7 CNC: ATCR7 C/NC: ATCR7, ANTCR7

N/A

6.6

Transmitted signal quality

–

–

–

–

–

–

–

6.6.2

OTA Frequency error

–

–

–

–

–

–

–

 

E-UTRA

Same TC as used in clause 6.6.4

Same TC as used in clause 6.6.4

Same TC as used in clause 6.6.4

Same TC as used in clause 6.6.4

Same TC as used in clause 6.6.4

Same TC as used in clause 6.6.4

Same TC as used in subclause 6.6.4

 

UTRA FDD

Same TC as used in clause 6. 6.4

Same TC as used in clause 6. 6.4

N/A

N/A

N/A

N/A

Same TC as used in subclause 6.6.4

NR

N/A

N/A

Same TC as used in clause 6.6.4

Same TC as used in clause 6.6.4

Same TC as used in clause 6.6.4

Same TC as used in subclause 6.6.4

6.6.3

OTA Time alignment error

–

–

–

–

–

–

–

 

E-UTRA

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Subclause 5.3.4

 

UTRA FDD

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

Subclause 5.3.3

NR

N/A

N/A

N/A

C: ATCR8

CNC: ATCR8

C/NC: ATCR8, ANTCR8

C: ATCR8

CNC: ATCR8

C/NC: ATCR8, ANTCR8

C: ATCR8

CNC: ATCR8

C/NC: ATCR8, ANTCR8

C: ATCR9

CNC: ATCR9

C/NC: ATCR9, ANTCR9

6.6.4

OTA Modulation quality – EVM

–

–

–

–

–

–

–

 

E-UTRA

C: ATCR3a CNC: ATCR3a C/NC: ATCR3a, ANTCR3

C: ATCR3a CNC: ATCR3a C/NC: ATCR3a, ANTCR3

N/A

C: ATCR7 CNC: ATCR7 C/NC: ATCR7, ANTCR7

C: ATCR7 CNC: ATCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ATCR7 C/NC: ATCR7, ANTCR7

C: ATCR9

CNC: ATCR9

C/NC: ATCR9, ANTCR9

 

UTRA FDD

C: ATCR3a CNC: ATCR3a C/NC: ATCR3a, ANTCR3

C: ATCR3a CNC: ATCR3a C/NC: ATCR3a, ANTCR3

N/A

N/A

N/A

N/A

C: ATCR9

CNC: ATCR9

C/NC: ATCR9, ANTCR9

NR

N/A

N/A

N/A

C: ATCR7 CNC: ATCR7 C/NC: ATCR7, ANTCR7

C: ATCR7 CNC: ATCR7 C/NC: ATCR7, ANTCR7

C: ATCR9

CNC: ATCR9

C/NC: ATCR9, ANTCR9

6.7

OTA Unwanted Emissions

–

–

–

–

–

–

–

6.7.2

OTA Occupied bandwidth

–

–

–

–

–

–

–

 

Minimum requirement

Clause 5.3.3 Clause 5.3.4

Clause 5.3.3 Clause 5.3.4

Clause 5.3.3 Clause 5.3.4

Clause 5.3.4

SC, ATCR8b (Note)

Clause 5.3.4

SC, ATCR8b (Note)

Clause 5.3.4

SC, ATCR8b (Note)

Subclause 5.3.3

Subclause 5.3.4

SC

6.7.3

OTA Adjacent Channel Leakage power Ratio

–

–

–

–

–

–

–

 

E-UTRA

C: ATCR2a CNC: ANTCR2 C/NC:ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC:ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC:ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC:ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC:ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC:ATCR2a, ANTCR2

C: ATCR9

CNC: ATCR9

C/NC: ATCR9, ANTCR9

 

UTRA FDD

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

Subclause 5.3.3

NR

N/A

N/A

N/A

C: ATCR8a

CNC: ANTCR8

C/NC: ATCR8a, ANTCR8

C: ATCR8a

CNC: ANTCR8

C/NC: ATCR8a, ANTCR8

C: ATCR8a

CNC: ANTCR8

C/NC: ATCR8a, ANTCR8

C: ATCR9

CNC: ATCR9

C/NC: ATCR9, ANTCR9

 

Cumulative ACLR

CNC: ANTCR3 C/NC:ANTCR3

CNC: ANTCR3 C/NC:ANTCR3

CNC: ANTCR7 C/NC:ANTCR7

CNC: ANTCR7 C/NC:ANTCR7

CNC: ANTCR7 C/NC:ANTCR7

CNC: ANTCR9

C/NC: ANTCR9

6.6.5

OTA Operating band unwanted emission

–

–

–

–

–

–

–

 

General requirement for Band Categories 1 and 3

Clause 5.3.3 Clause 5.3.4 C: ATCR3a CNC: ATCR3a, ANTCR3 C/NC: ATCR3a, ANTCR3

N/A

Clause 5.3.3 Clause 5.3.4

Clause 5.3.4

C: ATCR7 CNC: ATCR7, ANTCR7

C/NC: ATCR7, ANTCR7

N/A

Clause 5.3.4

C: ATCR7

CNC: ATCR7, ANTCR7

C/NC: ATCR7, ANTCR7

Subclause 5.3.3 Subclause 5.3.4

 

General requirement for Band Category 2

N/A

Clause 5.3.3 Clause 5.3.4
C: ATCR3a CNC: ATCR3a, ANTCR3 C/NC: ATCR3a, ANTCR3

N/A

N/A

Clause 5.3.4
C: ATCR7 CNC: ATCR7, ANTCR7

C/NC: ATCR7, ANTCR7

N/A

BC1: N/A

BC2:

Subclause 5.3.3

Subclause 5.3.4

C: ATCR9

CNC: ATCR9, ANTCR9

C/NC: ATCR9, ANTCR9

 

Additional requirements 

(note)

(note)

(note)

(note)

(note)

(note)

(note 1)

6.7.6

OTA Spurious emission

–

–

–

–

–

–

–

 

(Category A)

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

N/A

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR9

CNC: ANTCR9

C/NC: ATCR9, ANTCR9

 

(Category B)

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

N/A

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR9

CNC: ANTCR9

C/NC: ATCR9, ANTCR9

 

Protection of the BS receiver of own or different BS

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

C: ATCR3a CNC: ANTCR3C/NC: ATCR3a, ANTCR3

N/A

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR9

CNC: ANTCR9

C/NC: ATCR9, ANTCR9

 

Additional spurious emissions requirements

C: ATCR3a, CNC: ANTCR3, C/NC: ATCR3a, ATCR3a

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

N/A

C: ATCR7, CNC: ANTCR7, C/NC: ATCR7, ANTCR7

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR9

CNC: ANTCR9

C/NC: ATCR9, ANTCR9

 

Co-location with other Base Stations

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

N/A

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR9

CNC: ANTCR9

C/NC: ATCR9, ANTCR9

6.8

OTA Transmitter intermodulation

–

–

–

–

–

–

–

 

General requirement

Same TC as used in clause 6.7

Same TC as used in clause 6.7

Same TC as used in clause 6.7 

Same TC as used in clause 6.7

Same TC as used in clause 6.7

Same TC as used in clause 6.7 

Same TC as used in subclause 6.7 

 

Additional requirement (BC1 and BC2)

CNC: ANTCR3 C/NC:ANTCR3

Same TC as used in clause 6.7

N/A

CNC: ANTCR7 C/NC:ANTCR7a

Same TC as used in clause 6.7

N/A

BC1:

CNC: ANTCR9 C/NC:ANTCR9

BC2:

Same TC as used in subclause 6.7

 

Additional requirement (BC3)

N/A

N/A

Same TC as used in clause 6.7

N/A

N/A

N/A

N/A

7.2

OTA sensitivity

–

–

–

–

–

–

–

E-UTRA requirement

clause 5.3.4

clause 5.3.4

clause 5.3.4

clause 5.3.4

clause 5.3.4

clause 5.3.4

subclause 5.3.4

UTRA FDD requirement

clause 5.3.3

clause 5.3.3

N/A

N/A

N/A

N/A

subclause 5.3.3

UTRA TDD requirement

N/A

N/A

clause 5.3.3

N/A

N/A

N/A

N/A

NR requirement

N/A

N/A

N/A

ATCR4d

ATRC4d

ATCR4d

ATCR4d

7.3

OTA reference sensitivity level

–

–

–

–

–

–

–

E-UTRA requirement

clause 5.3.4

clause 5.3.4

clause 5.3.4

clause 5.3.4

clause 5.3.4

clause 5.3.4

subclause 5.3.4

UTRA FDD requirement

clause 5.3.3

clause 5.3.3

N/A

N/A

N/A

N/A

subclause 5.3.3

NR requirement

N/A

N/A

N/A

ATRC4d

ATCR4d

ATCR4d

ATCR4d

7.4

OTA Dynamic range

–

–

–

–

–

–

–

 

E-UTRA

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Subclause 5.3.4

 

UTRA FDD

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

Subclause 5.3.3

NR

N/A

N/A

N/A

ATCR4d

ATCR4d

ATCR4d

ATCR4d

7.5

OTA Adjacent channel selectivity and narrowband blocking

–

–

–

–

–

–

–

 

General blocking requirement

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

N/A

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR9

CNC: ANTCR9

C/NC: ATCR9, ANTCR9

 

General narrowband blocking requirement

C: ATCR3a, ATCR4b CNC:ANTCR3, ATCR4b C/NC: ATCR3a, ANTCR3,ATCR4b

C: ATCR3a, ATCR4b CNC:ANTCR3, ATCR4b C/NC: ATCR3a, ANTCR3,ATCR4b

C: ATCR4b

C: ATCR7, ATCR4b, ATCR4d CNC:ANTCR7, ATCR4b, ATCR4d

C/NC: ATCR7, ANTCR7,ATCR4b, ATCR4d

C: ATCR7, ATCR4b, ATCR4d CNC:ANTCR7, ATCR4b, ATCR4d

C/NC: ATCR7, ANTCR7,ATCR4b, ATCR4d

C: ATCR7, ATCR4b, ATCR4d

CNC: ANTCR7, ATCR4b, ATCR4d C/NC: ATCR7, ANTCR7, ATCR4b, ATCR4d

C:

ATCR9, ATCR4a, ATCR4b, ATCR4d

CNC:

ANTCR9, ATCR4a, ATCR4b, ATCR4d

C/NC:

ATCR9,

ANTCR9, ATCR4a, ATCR4b, ATCR4d

 

Additional BC3 blocking minimum requirement

N/A

N/A

N/A

N/A

N/A

N/A

N/A

7.6

OTA Blocking

–

–

–

–

–

–

–

 

General requirement

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

N/A

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR9

CNC: ANTCR9

C/NC: ATCR9, ANTCR9

 

Co-location requirement

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

N/A

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR9

CNC: ANTCR9

C/NC: ATCR9, ANTCR9

7.7

OTA Receiver spurious emissions

–

–

–

–

–

–

–

 

General requirement

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

N/A

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR9

CNC: ANTCR9

C/NC: ATCR9, ANTCR9

 

Additional requirement for BC2 (Category B)

N/A

N/A

N/A

N/A

N/A

N/A

N/A

7.8

OTA Receiver intermodulation

–

–

–

–

–

–

–

 

General intermodulation requirement

C: ATCR3a CNC: ANTCR3 C/NC: ATCR3a, ANTCR3

C: ATCR3a CNC ANTCR3 C/NC: ATCR3a, ANTCR3

N/A

C: ATCR7 CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR7

CNC: ANTCR7 C/NC: ATCR7, ANTCR7

C: ATCR9

CNC: ANTCR9

C/NC: ATCR9, ANTCR9

 

General narrowband intermodulation requirement

C: ATCR3a, ATCR4b CNC:ANTCR3, ATCR4b C/NC: ATCR3a, ANTCR3, ATCR4b

C: ATCR3a ATCR4b CNC:ANTCR3,ATCR4b C/NC: ATCR3a, ANTCR3; ATCR4b

C: ATCR4b

C: ATCR7, ATCR4b, ATCR4d CNC:ANTCR7, ATCR4b, ATCR4d

C/NC: ATCR7, ANTCR7, ATCR4b, ATCR4d

C: ATCR7 ATCR4b, ATCR4d CNC:ANTCR7,ATCR4b, ATCR4d

C/NC: ATCR7, ANTCR7; ATCR4b, ATCR4d

C: ATCR7, ATCR4b, ATCR4d CNC: ANTCR7, ATCR4b, ATCR4d C/NC: ATCR7, ANTCR7, ATCR4b, ATCR4d

C:

ATCR9, ATCR4a, ATCR4b, ATCR4d

CNC:

ANTCR9, ATCR4a, ATCR4b, ATCR4d

C/NC:

ATCR9,

ANTCR9, ATCR4a, ATCR4b, ATCR4d

7.9

OTA In-channel selectivity

–

–

–

–

–

–

–

E-UTRA requirement

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Subclause 5.3.4

NR requirement

N/A

N/A

N/A

ATCR4d

ATCR4d

ATCR4d

ANTCR9

NOTE 1: ATCR8b is only applicable when contiguous CA is supported

NOTE 2: For Operating band unwanted emissions, NR shall also be tested with SC with widest supported channel bandwidth and highest supported sub-carrier spacing.

5.3 Test configurations for multi-carrier capable AAS BS in operating bands where one RAT capability sets are supported

5.3.1 General

An AAS BS may support only one RAT operation in an operating band by fulfilling different sets of requirements. Both UTRA and E-UTRA have two complete sets of requirements that may be fulfilled depending on whether the beam is declared to be MSR or single RAT in the operating band. MSR and single RAT requirements are addressed separately by separate test requirements (and corresponding core requirements). They are also identified by different capability sets as described in clauses 4.11 and 5.2.

5.3.2 AAS BS supporting one RAT only MSR in the operating band

This clause contains test configuration applicability to requirements and capability sets for AAS BS supporting one RAT only MSR operation operating with multiple carriers (MC).

Table 5.3.2-1: Test configuration applicability to requirements
and capability sets for operating bands supporting one RAT only MSR operation

Capability Set

UTRA (MC) capable BS (RCSA1)

E-UTRA (MC) capable BS (RCSA2)

Test case

BC1

BC2

BC3

BC1

BC2

BC3

6.2

Radiated transmit power

C: ATCR1a CNC: ATCR1a C/NC: ATCR1a, ANTCR1a

C: ATCR1a CNC: ATCR1a C/NC: ATCR1a, ANTCR1a

C: ATCR1b

C: ATCR2a CNC: ATCR2a C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ATCR2a C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ATCR2a C/NC: ATCR2a, ANTCR2

6.3

OTA Base Station output power

–

–

–

–

–

–

6.3.2

OTA maximum output power

C: ATCR1a CNC: ATCR1a C/NC: ATCR1a, ANTCR1a

C: ATCR1a CNC: ATCR1a C/NC: ATCR1a, ANTCR1a

N/A

C: ATCR2a CNC: ATCR2a C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ATCR2a C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ATCR2a C/NC: ATCR2a, ANTCR2

6.3.3

OTA E-UTRA DL RS power

N/A

N/A

N/A

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

6.4

OTA Output power dynamics

–

–

–

–

–

–

6.4.2

OTA UTRA Inner loop power control in the downlink

N/A

N/A

N/A

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

6.4.3

OTA Power control dynamic range

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

6.4.4

OTA Total power dynamic range

N/A

N/A

Clause 5.3.3

N/A

N/A

N/A

6.4.5

OTA IPDL time mask

Clause 5.3.3

Clause 5.3.3

N/A

 

 

 

6.4.6

OTA RE Power control dynamic range

N/A

N/A

N/A

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

6.5

OTA Transmit ON/OFF power

–

–

–

–

–

–

6.5.1

OTA Transmitter OFF power

N/A

N/A

N/A

N/A

N/A

C: ATCR2a CNC: ATCR2a C/NC: ATCR2a, ANTCR2

6.5.2

OTA Transmitter transient period

N/A

N/A

N/A

N/A

N/A

C: ATCR2a CNC: ATCR2a C/NC: ATCR2a, ANTCR2

6.6

OTA signal quality

–

–

–

–

–

–

6.6.2

OTA Frequency error

–

–

–

–

–

–

 

E-UTRA

N/A

N/A

N/A

Same TC as used in clause 6.5.4

Same TC as used in clause 6.5.4

Same TC as used in clause 6.5.4

 

UTRA FDD

Same TC as used in clause 6.5.4

Same TC as used in clause 6.5.4

N/A

N/A

N/A

N/A

6.6.3

OTA Time alignment error

–

–

–

–

–

–

 

E-UTRA

N/A

N/A

N/A

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

 

UTRA FDD

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

6.6.4

OTA Modulation quality – EVM

–

–

–

–

–

–

 

E-UTRA

N/A

N/A

N/A

C: ATCR2a CNC: ATCR2a C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ATCR2a C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ATCR2aC/NC: ATCR2a, ANTCR2

 

UTRA FDD

C: ATCR1a CNC: ATCR1a C/NC: ATCR1a, ANTCR1a

C: ATCR1a CNC: ATCR1a C/NC: ATCR1a, ANTCR1a

N/A

N/A

N/A

N/A

6.7

OTA Unwanted Emissions

–

–

–

–

–

–

6.7.2

OTA Occupied bandwidth

–

–

–

–

–

–

 

Minimum requirement

Clause 5.3.3

Clause 5.3.3

Clause 5.3.3

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

6.7.3

OTA Adjacent Channel Leakage power Ratio

 

–

–

–

–

–

 

E-UTRA

N/A

N/A

N/A

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

 

UTRA FDD

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

 

Cumulative ACLR

CNC: ANTCR1a C/NC: ANTCR1a

CNC: ANTCR1a C/NC: ANTCR1a

– 

CNC: ANTCR2 C/NC: ANTCR2

CNC: ANTCR2 C/NC: ANTCR2

CNC: ANTCR2 C/NC: ANTCR2

6.7.4

OTA Spectrum emission mask

 

 

 

 

 

 

6.7.5

OTA Operating band unwanted emission

–

–

–

–

–

–

 

General requirement for Band Categories 1 and 3

Clause 5.3.3

C: ATCR1a CNC: ATCR1a, ANTCR1a C/NC: ATCR1a, ANTCR1a

N/A

Clause 5.3.3

Clause 5.3.4

C: ATCR2a CNC: ATCR2a, ANTCR2 C/NC: ATCR2a, ANTCR2

N/A

Clause 5.3.4

C: ATCR2a CNC: ATCR2a, ANTCR2 C/NC: ATCR2a, ANTCR2

 

General requirement for Band Category 2

N/A

Clause 5.3.3

C: ATCR1a CNC: ATCR1a, ANTCR1a C/NC: ATCR1a, ANTCR1a

N/A

N/A

Clause 5.3.4

C: ATCR2a CNC: ATCR2a, ANTCR2 C/NC: ATCR2a, ANTCR2

N/A

 

Additional requirements 

(note)

(note)

(note)

(note)

(note)

(note)

6.7.6

OTA Spurious emission

–

–

–

–

–

–

 

(Category A)

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

N/A

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

 

(Category B)

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

N/A

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

 

Protection of the BS receiver of own or different BS

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

N/A 

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

 

Additional spurious emissions requirements

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

N/A

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

 

Co-location with other Base Stations

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

N/A 

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2C/NC: ATCR2a, ANTCR2

6.8

OTA Transmitter intermodulation

–

–

–

–

–

–

 

General requirement

Same TC as used in clause 6.6

Same TC as used in clause 6.6

Same TC as used in clause 6.6

Same TC as used in clause 6.6

Same TC as used in clause 6.6

Same TC as used in clause 6.6 

 

Additional requirement (BC1 and BC2)

CNC: ANTCR1a C/NC:ANTCR1a

Same TC as used in 6.6

N/A

CNC: ANTCR2 C/NC: ANTCR2

Same TC as used in 6.6

N/A

 

Additional requirement (BC3)

N/A

N/A

Same TC as used in clause 6.6 

N/A

N/A

Same TC as used in 6.6

7.2

OTA sensitivity

–

–

–

–

–

–

 

E-UTRA requirement

N/A

N/A

N/A

clause 5.3.4

clause 5.3.4

clause 5.3.4

 

UTRA FDD requirement

clause 5.3.3

clause 5.3.3

N/A

N/A

N/A

N/A

 

UTRA TDD requirement

N/A

N/A

clause 5.3.3

N/A

N/A

N/A

7.3

OTA Reference sensitivity level

–

–

–

–

–

–

 

E-UTRA requirement

N/A

N/A

N/A

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

 

UTRA FDD requirement

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

7.4

OTA Dynamic range

–

–

–

–

–

–

 

E-UTRA

N/A

N/A

N/A

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

 

UTRA FDD

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

7.5

OTA Adjacent channel selectivity and narrowband blocking

–

–

–

–

–

–

 

General blocking requirement

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a , ANTCR1a

C: ATCR1a, NC: ANTCR1a C/NC: ATCR1a , ANTCR1a

N/A

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

 

General narrowband blocking requirement

C: ATCR1a, ATCR4a CNC: ANTCR1a, ATCR4a C/NC: ATCR1a, ANTCR1a, ATCR4a

C: ATCR1a, ATCR4a CNC:ANTCR1a, ATCR4a C/NC: ATCR1a, ANTCR1a, ATCR4a

N/A

C: ATCR2a, ATCR4b CNC:ANTCR2, ATCR4b C/NC: ATCR2a, ANTCR2

C: ATCR2a, ATCR4b CNC: ANTCR2, ATCR4b C/NC: ATCR2a, ANTCR2, ATCR4b

C: ATCR2a, ATCR4b CNC: ANTCR2, ATCR4b C/NC: ATCR2a, ANTCR2, ATCR4b

 

Additional BC3 blocking minimum requirement

N/A

N/A

N/A

N/A

N/A

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

7.6

OTA Blocking

–

–

–

–

–

–

 

General requirement

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

N/A

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

 

Co-location requirement

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

N/A

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

7.7

OTA Receiver spurious emissions

–

–

–

–

–

–

 

General requirement

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a, ANTCR1a

N/A

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

7.8

OTA Receiver intermodulation

–

–

–

–

–

–

 

General intermodulation requirement

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a , ANTCR1a

C: ATCR1a CNC: ANTCR1a C/NC: ATCR1a , ANTCR1a

N/A

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

C: ATCR2a CNC: ANTCR2 C/NC: ATCR2a, ANTCR2

 

General narrowband intermodulation requirement

C: ATCR1a, ATCR4a CNC:ANTCR1a, ATCR4a C/NC: ATCR1a, ANTCR1a, ATCR4a

C: ATCR1a, ATCR4a CNC:ANTCR1a, ATCR4a C/NC: ATCR1a, ANTCR1a, ATCR4a

N/A

C: ATCR2a, ATCR4b CNC: ANTCR2, ATCR4b C/NC: ATCR2a, ANTCR2, ATCR4b

C: ATCR2a, ATCR4b CNC: ANTCR2, ATCR4b C/NC: ATCR2a, ANTCR2, ATCR4b

C: ATCR2a, ATCR4b CNC: ANTCR2, ATCR4b C/NC: ATCR2a, ANTCR2, ATCR4b

7.9

OTA In-channel selectivity

–

–

–

–

–

–

 

E-UTRA requirement

N/A

N/A

N/A

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

5.3.3 AAS BS supporting Single-RAT UTRA in the operating band

This clause contains the test configurations for AAS BS supporting single-RAT UTRA in the operating band. The test configurations apply to beams operating with multiple carriers (MC).

For an AAS BS declared to support multi-carrier operation in contiguous spectrum operation in single band only, the test configurations in the second column of table 5.3.3-1 for FDD, and in the fifth column of table 5.3.3-1 for TDD, shall be used for testing.

NOTE: The applicability of test configurations for TDD in this clause is only applicable to UTRA TDD 1,28 Mcps option.

For FDD an AAS BS declared to support multi-carrier operation in contiguous and non-contiguous spectrum in single band and where the parameters in the manufacture’s declaration according to clause 4.10 are identical for contiguous (C) and non-contiguous (NC) spectrum operation, the test configurations in the third column of table 5.3.3-1 shall be used for testing.

For FDD an AAS BS declared to support multi-carrier operation in contiguous and non-contiguous spectrum in single band and where the parameters in the manufacture’s declaration according to clause 4.10 are not identical for contiguous and non-contiguous spectrum operation, the test configurations in the fourth column of table 5.3.3-1 shall be used for testing.

Table 5.3.3-1: Test configurations for a AAS BS supporting single-RAT UTRA operation

test case

Single-RAT UTRA FDD MC capable AAS BS operating band (RCSA4)
C capable only

Single-RAT UTRA FDD MC capable AAS BS operating band (RCSA4)
C and NC capable with identical parameters

Single-RAT UTRA FDD MC capable AAS BS operating band (RCSA4)
C and NC capable with different parameters

Single-RAT UTRA TDD MC AAS BS operating band (RCSA4)
C capable only

6.2

Radiated Transmit Power

ATCR1a

ATCR1a

ATCR1a, ANTCR1

ATCR1b

6.3

OTA Base Station output power

–

–

–

 N/A

6.3.2

Base Station maximum output power

ATC1a

ATC1a

ATC1a, ANTC1

 N/A

6.4

OTA Output power dynamics

–

–

–

 N/A

6.4.2

OTA UTRA Inner loop power control in the downlink

SC

SC

SC

 N/A

6.4.3

OTA Power control dynamic range

SC

SC

SC

 N/A

6.4.4

OTA Total power dynamic range

SC or ATC1a

SC or ATC1a

SC or ATC1a

N/A 

6.4.5

OTA IPDL time mask

SC

SC

SC

 N/A

6.6

OTA Transmitted signal quality

–

–

–

 N/A

6.6.2

OTA Frequency error

ATC1a

ATC1a

ATC1a, ANTC1

 N/A

6.6.3

OTA Time alignment error

ATC1a

ATC1a

ATC1a, ANTC1

 N/A

6.6.4

OTA Modulation quality – EVM

ATC1a

ATC1a

ATC1a, ANTC1

 N/A

6.6.4

OTA Modulation quality – PCDE

ATC1a

ATC1a

ATC1a, ANTC1

 N/A

6.6.4

OTA Modulation quality – RCDE

ATC1a

ATC1a

ATC1a

 N/A

6.7

OTA Unwanted Emissions

–

–

–

 N/A

6.7.2

OTA Occupied bandwidth

SC

SC

SC

 N/A

6.7.3

OTA Adjacent Channel Leakage power Ratio

ATC1a

ANTC1

ATC1a, ANTC1

 N/A

 

Cumulative ACLR

–

ANTC1

ANTC1

 N/A

6.7.4

OTA Spectrum emission mask

ATC1a

ATC1a, ANTC1

ATC1a, ANTC1

 N/A

6.7.6

OTA Spurious emission

ATC1a

ANTC1

ATC1a, ANTC1

 N/A

6.8

OTA Transmitter intermodulation

ATC1a

ATC1a, ANTC1

ATC1a, ANTC1

 N/A

7.2

OTA sensitivity

ATCR4a

ATCR4a

ATCR4a

ATCR4c

7.3

OTA Reference sensitivity level

ATCR4a

ATCR4a

ATCR4a

 N/A

7.4

OTA Dynamic range

ATCR4a

ATCR4a

ATCR4a

 N/A

7.5

OTA Adjacent channel selectivity and narrowband blocking

ATCR1a

ANTCR1

ATCR1a, ANTCR1

 N/A

7.6

OTA Blocking

ATCR1a

ANTCR1

ATCR1a, ANTCR1

 N/A

7.7

OTA Receiver spurious emissions

ATCR1a

ANTCR1

ATCR1a, ANTCR1

 N/A

7.8

OTA Receiver intermodulation

ATCR1a

ANTCR1

ATCR1a, ANTCR1

 N/A

5.3.4 AAS BS supporting Single-RAT E-UTRA in the operating band

This clause contains the test configurations for AAS BS supporting single-RAT E-UTRA in the operating band. The test configurations apply to AAS BS operating bands operating with multiple carriers (MC).

For an AAS BS declared to support multi-carrier and/or CA operation in contiguous spectrum operation in single band only, the test configurations in the second column of table 5.3.4-1 shall be used for testing.

For an AAS BS declared to support multi-carrier and/or CA operation in contiguous and non-contiguous spectrum in single band and where the parameters in the manufacture’s declaration according to clause 4.10 are identical for contiguous (C) and non-contiguous (NC) spectrum operation, the test configurations in the third column of table 5.3.4-1 shall be used for testing.

For an AAS BS declared to support multi-carrier and/or CA in contiguous and non-contiguous spectrum in single band and where the parameters in the manufacture’s declaration according to clause 4.10 are not identical for contiguous and non-contiguous spectrum operation, the test configurations in the fourth column of table 5.3.4-1 shall be used for testing.

Table 5.3.4-1: Test configurations for a AAS BS supporting single-RAT E-UTRA operation capable of
both contiguous and non-contiguous spectrum in multi-carrier and/or CA operation in single band

test case

Single-RAT E-UTRA MC capable AAS BS operating band (RCSA5)

C capable only

Single-RAT E-UTRA MC capable AAS BS operating band (RCSA5)

C and NC capable BS with identical parameters

Single-RAT E-UTRA MC capable AAS BS operating band (RCSA5)

C and NC capable BS with different parameters 

6.2

Radiated Transmit Power

ATCR2a

ATCR2a

ATCR2a, ANTCR2

6.3

OTA Base Station output power

–

–

–

6.3.2

OTA Base Station maximum output power

ATCR2a

ATCR2a

ATCR2a, ANTCR2

6.3.3

OTA E-UTRA DL RS power

SC

SC

SC

6.4

OTA Output power dynamics

–

–

–

6.4.4

OTA Total power dynamic range

SC

SC

SC

6.4.6

OTA RE Power control dynamic range

Tested with Error Vector Magnitude

Tested with Error Vector Magnitude

Tested with Error Vector Magnitude

6.5

OTA Transmit ON/OFF power

ATCR2a

ATCR2a

ATCR2a, ANTCR2

6.6

OTA Transmitted signal quality

–

–

–

6.6.2

OTA Frequency error

Tested with Error Vector Magnitude

Tested with Error Vector Magnitude

Tested with Error Vector Magnitude

6.6.3

OTA Time alignment error

ATCR2a

ATCR2a

ATCR2a, ANTCR2

6.6.4

OTA Modulation quality – EVM

ATCR2a

ATCR2a

ATCR2a, ANTCR2

6.7

OTA Unwanted Emissions

–

–

–

6.7.2

OTA Occupied bandwidth

SC, ATCR2b (Note)

SC, ATCR2b (Note)

SC, ATCR2b (Note)

6.7.3

OTA Adjacent Channel Leakage power Ratio

ATCR2a

ATCR2a, ANTCR2

ATCR2a, ANTCR2

6.7.3

OTA Cumulative ACLR

–

ANTCR2

ANTCR2

6.7.5

OTA Operating band unwanted emission

ATCR2a

ATCR2a, ANTCR2

ATCR2a, ANTCR2

6.7.6

OTA Spurious emission

ATCR2a

ANTCR2

ATCR2a, ANTCR2

6.8

OTA Transmitter intermodulation

ATCR2a

Same TC as used in 6.6

Same TC as used in 6.6

7.2

OTA sensitivity

ATCR4b

ATCR4b

ATCR4b

7.3

OTA Reference sensitivity level

ATCR4b

ATCR4b

ATCR4b

7.4

OTA Dynamic range

ATCR4b

ATCR4b

ATCR4b

7.5

OTA Adjacent channel selectivity and narrowband blocking

ATCR2a

ANTCR2

ATCR1, ANTCR2

7.6

OTA Blocking

ATCR2a

ANTCR2

ATCR2a, ANTCR2

7.7

OTA Receiver spurious emissions

ATCR2a

ANTCR2

ATCR2a, ANTCR2

7.8

OTA Receiver intermodulation

ATCR2a

ANTCR2

ATCR2a, ANTCR2

7.9

OTA In-channel selectivity

ATCR4b

ATCR4b

ATCR4b

NOTE: ATCR2b is only applicable when contiguous CA is supported. 

5.4 Test configurations for AAS BS operating bands with multi-band dependencies

5.4.1 AAS BS operating bands with multi-band dependencies supporting MSR operation

Table 5.4.1-1: Test configuration for AAS BS operating bands containing beams
with multi-band dependencies supporting MSR operation

test case

Test for AAS BS operating bands with multi-band dependencies

Test configuration for MBT

RCSA1,RCSA2, RCSA3, RCSA3A

BC1/BC2

BC3

6.2

Radiated Transmit Power

SBT, MBT

ATCR5a

ATCR5a

6.3

OTA Base Station output power

–

–

–

6.3.2

OTA Base Station maximum output power

SBT, MBT

ATCR5a

ATCR5a

6.3.3

OTA E-UTRA DL RS power

E-UTRA for DL RS power

SBT

–

6.4

OTA Output power dynamics

–

–

–

6.4.2

OTA UTRA Inner loop power control in the downlink

SBT

–

–

6.4.3

OTA Power control dynamic range

SBT

–

–

6.4.4

OTA Total power dynamic range

SBT

–

N/A

6.4.5

OTA IPDL time mask

SBT

–

N/A

6.4.6

OTA RE Power control dynamic range

SBT

–

N/A

6.5

OTA Transmit ON/OFF power

–

–

–

6.5.1

OTA Transmitter OFF power

MBT, SBT (note 3)

N/A

ATCR5a

6.5.2

OTA Transmitter transient period

MBT, SBT (note 3)

N/A

ATCR5a

6.6

OTA Transmitted signal quality

–

–

–

6.6.2

OTA Frequency error

–

–

–

 

E-UTRA

SBT, MBT

ATCR5a

ATCR5a

 

UTRA FDD

SBT, MBT

ATCR5a

N/A

NR

SBT, MBT

ATCR5a

ATCR5a

6.6.3

OTA Time alignment error

–

–

–

 

E-UTRA

SBT, MBT (note 1)

ATCR5b

ATCR5b

 

UTRA FDD

SBT, MBT (note 1)

ATCR5b

N/A

NR

SBT, MBT (note 1)

ATCR5b

ATCR5b

6.6.4

OTA Modulation quality – EVM

–

–

–

 

E-UTRA

SBT, MBT

ATCR5a

ATCR5a

 

UTRA FDD

SBT, MBT

ATCR5a

N/A

NR

SBT, MBT

ATCR5a

ATCR5a

6.7

OTA Unwanted Emissions

–

–

–

6.6.2

OTA Occupied bandwidth

–

–

–

 

Minimum requirement

SBT

–

–

6.7.3

OTA Adjacent Channel Leakage power Ratio

–

–

–

 

E-UTRA

SBT, MBT (note 2)

ATCR5b

ATCR5b

 

UTRA FDD

SBT, MBT (note 2)

ATCR5b

N/A

NR

SBT, MBT (note 2)

ATCR5b

ATCR5b

 

Cumulative ACLR

SBT, MBT (note 2)

ATCR5b

ATCR5b 

6.7.4

OTA Spectrum emission mask

–

–

–

6.7.5

OTA Operating band unwanted emission

–

–

–

 

General requirement for Band Categories 1 and 3

SBT, MBT

ATCR5b

ATCR5b 

 

General requirement for Band Category 2

SBT, MBT

ATCR5b

N/A

 

Additional requirements 

SBT, MBT

–

–

6.7.6

OTA Spurious emission

–

–

–

 

(Category A)

SBT, MBT

ATCR5b

ATCR5b 

 

(Category B)

SBT, MBT

ATCR5b

ATCR5b 

 

Protection of the BS receiver of own or different BS

SBT, MBT

ATCR5b

ATCR5b 

 

Additional spurious emissions requirements

SBT, MBT

ATCR5b

ATCR5b 

 

Co-location with other Base Stations

–

–

–

6.8

OTA Transmitter intermodulation

–

–

–

 

General requirement

SBT

–

–

 

Additional requirement (BC1 and BC2)

SBT

–

N/A

 

Additional requirement (BC3)

SBT

N/A

–

7.2

OTA sensitivity

SBT

ATCR4a,ATCR4b

None

7.3

OTA Reference sensitivity level

–

–

–

 

E-UTRA requirement

SBT

–

–

 

UTRA FDD requirement

SBT

–

–

NR requirement

SBT

–

–

7.4

OTA Dynamic range

–

–

–

 

E-UTRA

SBT

–

–

 

UTRA FDD

SBT

–

–

NR

SBT

–

–

7.5

OTA Adjacent channel selectivity and narrowband blocking

–

–

–

 

General blocking requirement

MBT, SBT (note 3)

ATCR5b

ATCR5b 

 

General narrowband blocking requirement

MBT, SBT (note 3)

ATCR5b

ATCR5b 

7.6

OTA Blocking

–

–

–

 

General requirement

MBT, SBT(note 3)

ATCR5b

ATCR5b 

 

Co-location requirement

MBT, SBT(note 3)

ATCR5b

ATCR5b 

7.7

OTA Receiver spurious emissions

–

–

–

 

General requirement

SBT, MBT

ATCR5b

ATCR5b 

7.8

OTA Receiver intermodulation

–

–

–

 

General intermodulation requirement

MBT, SBT(note 3)

ATCR5b

ATCR5b 

 

General narrowband intermodulation requirement

MBT, SBT(note 3)

ATCR5b

ATCR5b 

7.9

OTA In-channel selectivity

–

–

–

 

E-UTRA requirement

SBT

–

–

NR requirement

SBT

–

–

NOTE 1: MBT is only applicable when DB-DC-HSDPA or inter-band CA is supported.

NOTE 2: For ACLR, MBT shall be applied for the Inter RF bandwidth gap only.

NOTE 3: SBT is only applicable if different Capability Sets are declared for single-band and multi-band operation.

5.4.2 AAS BS operating bands with multi-band dependencies supporting Single-RAT only

For an AAS BS operating bands with multi-band dependencies supporting single-RAT only in the operational band, the test configurations in table 5.4.2-1, shall be used for testing.

Table 5.4.2-1: Test configuration for AAS BS operating bands with multi-band dependencies supporting Single-RAT only

test case

UTRA FDD RCSA4

UTRA TDD RCSA4

E-UTRA Test RCSA5

6.2

Radiated Transmit Power

ATCR1a/ANTCR1 (Note 1) ATCR5a

ATCR1b (Note 3), ATCR5a

ATCR2a/ANTCR2 (Note 5), ATCR5a

6.3

OTA Base Station output power

–

–

–

6.3.2

OTA Base Station maximum output power

ATCR1a/ANTCR1 (note 1) ATCR5a

N/A

ATCR2a/ANTCR2 (note 6), ATCR5a

6.3.3

OTA E-UTRA DL RS power

N/A

N/A

SC

6.4

OTA Output power dynamics

–

–

–

6.4.2

OTA UTRA Inner loop power control in the downlink

SC

N/A

N/A

6.4.3

OTA Power control dynamic range

SC

N/A

SC

6.4.4

OTA Total power dynamic range

SC or ATCR1a

N/A

SC

6.4.5

OTA IPDL time mask

SC

N/A

N/A

6.4.6

OTA RE Power control dynamic range

N/A

N/A

Tested with Error Vector Magnitude

6.5

OTA Transmit ON/OFF power

–

–

–

6.5.1

OTA Transmitter OFF power

N/A

N/A

ATCR5a (only applied for E‑UTRA TDD BS)

6.5.2

OTA Transmitter transient period

N/A

N/A

SC

6.6

OTA Transmitted signal quality

–

–

–

6.6.2

OTA Frequency error

Tested with EVM

N/A

Tested with Error Vector Magnitude

6.6.3

OTA Time alignment error

ATCR1a/ANTCR1 (note 1) ATCR5b

N/A

ATCR2a/ANTCR2 (note 6), ATCR5b (note 7)

6.6.4

OTA Modulation quality – EVM

ATCR1a/ANTCR1 (note 1), ATCR5a

N/A

ATCR2a/ANTCR2 (note 6), ATCR5a

6.6.4

OTA Modulation quality – PCDE

ATCR1a/ANTCR1 (note 1)

N/A

N/A

6.6.4

OTA Modulation quality – RCDE

ATCR1

N/A

N/A

6.7

OTA Unwanted Emissions

–

–

–

6.7.2

OTA Occupied bandwidth

SC

N/A

SC, ATCR2b (note 8)

6.7.3

OTA Adjacent Channel Leakage power Ratio

ATCR1a/ANTCR1 (note 1) ATCR5b (note 2)

N/A

ATCR2a/ANTCR2 (note 6), ATCR5b (note 9)

6.7.4

OTA Spectrum emission mask

ATCR1a/ANTCR1 (note 1) ATCR5b

N/A

N/A

6.7.5

OTA Operating band unwanted emission

N/A

N/A

ATCR2a/ANTCR2 (note 6), ATCR5b

6.7.6

OTA Spurious emission

ATCR1a/ANTCR1 (note 1) ATCR5b

N/A

ATCR2a/ANTCR2 (note 6), ATCR5b

6.8

OTA Transmitter intermodulation

ATCR1a/ANTCR1 (note 1)

N/A

ATCR2a/ANTCR2 (note 6)

7.2

Reference sensitivity level

ATCR4a

ATCR4c

ATCR4b

7.3

OTA Reference sensitivity level

ATCR4a

N/A

ATCR4a

7.4

OTA Dynamic range

ATCR4a

N/A

ATCR4a

7.5

OTA Adjacent channel selectivity and narrowband blocking

ATCR5b

N/A

ATCR5b

7.6

OTA Blocking

ATCR5b

N/A

ATCR5b

7.7

OTA Receiver spurious emissions

ATCR1a/ANTC1 (note 1) ATCR5b

N/A

ATCR2a/ANTC2 (note 6), ATCR5b

7.8

OTA Receiver intermodulation

ATCR5b

N/A

ATCR5b

7.9

OTA In-channel selectivity

N/A

N/A

ATCR4a

NOTE 1: ATCR1a and/or ANTCR1 shall be applied in each supported operating band according to table 5.3.3-1.

NOTE 2: ATCR5b may be applied for Inter RF Bandwidth gap only.

NOTE 3: ATCR1b shall be applied in each supported operating band according to table 5.3.3-1.

NOTE 4: Void

NOTE 5: ATCR5a may be applied for Inter RF bandwidth gap only.

NOTE 6: ATCR2 and/or ANTCR2 shall be applied in each supported operating band according to table 5.3.4-1.

NOTE 7: ATCR5b is only applicable when inter-band CA is supported.

NOTE 8: ATCR2b is only applicable when contiguous CA is supported.

NOTE 9: ATCR5b may be applied for Inter RF bandwidth gap only.