A.8.7 Combined Interfrequency and E-UTRAN measurements
25.1333GPPRelease 17Requirements for support of radio resource management (FDD)TS
A.8.7.1 Correct reporting of E-UTRA FDD neighbours in fading propagation condition
A.8.7.1.1 Test Purpose and Environment
The purpose of this test is to verify that the UE makes correct reporting of an event when doing inter frequency and E-UTRAN FDD measurements. The test will partly verify the requirements in section 8.1.2.3 and 8.1.2.6. The requirements are also applicable for a UE not requiring compressed mode for inter-frequency or inter-RAT E-UTRAN FDD measurements. In case a UE is not requiring compressed mode for inter-frequency measurements no compressed mode pattern with measurement purpose "FDD measurement" should be sent and in case a UE is not requiring compressed mode for inter-RAT E-UTRAN measurements no compressed mode pattern with measurement purpose "E-UTRAN measurements" should be sent for the parameters specified in table A8.30.
The test consists of two successive time periods, with time durations T1 and T2. The test parameters are given in tables A.8.30, A.8.31 and A.8.32 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2B and 3A shall be used.
Table A.8.30: General test parameters for Correct reporting of neighbours in Fading propagation condition
|
Parameter |
Unit |
Value |
Comment |
|
DCH parameters |
DL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.101 section A.3.1 |
|
|
Power Control |
On |
||
|
Compressed mode Interfrequency measurements E-UTRAN measurement |
DL compressed mode reference pattern 2, set 5 DL compressed mode reference pattern 2, set 5 |
Only applicable for UE requiring compressed mode patterns. As specified in table A.22 TS 25.101 section A.5 As specified in table A.22 TS 25.101 section A.5 |
|
|
Active cell |
Cell 1 |
||
|
Inter-RAT measurement quantity |
E-UTRAN RSRP |
||
|
Absolute Threshold (Ec/N0) used frequency |
dB |
-9 |
Ec/N0 threshold for Event 2b and 3a |
|
Absolute Threshold (Ec/N0) used for a not used frequency |
dB |
-18 |
Ec/IN0 threshold for Event 2b |
|
Threshold other system |
dBm |
-96 |
Absolute E-UTRA RSRP threshold for event 3a. |
|
Time to Trigger |
ms |
0 |
|
|
Filter coefficient |
0 |
||
|
Monitored cell list size |
Total 24 FDD neighbours 8 on frequency Channel 2 |
Measurement control information is sent before the compressed mode pattern starts. |
|
|
T1 |
s |
≥1 |
|
|
T2 |
s |
10 |
TableA.8.31: Cell Specific parameters for Correct reporting of neighbours in Fading propagation condition
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
||
|
T1 |
T2 |
T1 |
T2 |
||
|
UTRA RF Channel Number |
Channel 1 |
Channel 2 |
|||
|
CPICH_Ec/Ior |
dB |
-10 |
-10 |
||
|
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
||
|
SCH_Ec/Ior |
dB |
-12 |
-12 |
||
|
PICH_Ec/Ior |
dB |
-15 |
-15 |
||
|
DPCH_Ec/Ior |
dB |
Note 1 |
N/A |
||
|
OCNS |
Note 2 |
-0.941 |
|||
|
|
dB |
0 |
-Infinity |
-1.8 |
|
|
|
dBm/3,84 MHz |
-70 |
-70 |
||
|
CPICH_Ec/Io |
dB |
-13 |
-Infinity |
-14 |
|
|
Propagation Condition |
AWGN |
Case 5 as specified in Annex B of TS25.101 |
|||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior |
|||||
Table A.8.32: Cell specific test parameters for Correct reporting of E-UTRAN FDD neighbours in fading propagation condition (cell 3)
|
Parameter |
Unit |
Cell 3 |
|
|
T1 |
T2 |
||
|
E-UTRA RF Channel Number |
1 |
||
|
BWchannel |
MHz |
10 |
|
|
OCNG Pattern defined in A.3.2.1.2 in 3GPP TS 36.133 (OP.2 FDD) |
OP.2 FDD |
||
|
PBCH_RA |
dB |
0 |
|
|
PBCH_RB |
dB |
||
|
PSS_RA |
dB |
||
|
SSS_RA |
dB |
||
|
PCFICH_RB |
dB |
||
|
PHICH_RA |
dB |
||
|
PHICH_RB |
dB |
||
|
PDCCH_RA |
dB |
||
|
PDCCH_RB |
dB |
||
|
PDSCH_RA |
dB |
||
|
PDSCH_RB |
dB |
||
|
OCNG_RANote 1 |
dB |
||
|
OCNG_RBNote 1 |
dB |
||
|
|
dBm/15 kHz |
-98 |
|
|
|
dB |
-Infinity |
13 |
|
|
dB |
-Infinity |
13 |
|
RSRP Note 3 |
dBm/15 kHz |
-Infinity |
-85 |
|
SCH_RP Note 3 |
dBm/15 kHz |
-Infinity |
-85 |
|
Io Note 3 |
dBm/9 MH |
-70.22 |
-57.01 |
|
Propagation Condition |
ETU70 (Note 4) |
||
|
Note 1: OCNG shall be used such that both cells are fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols. OCNG patterns are specified in annex A 3.2 of 3GPP TS 36.133. Note 2: Interference from other cells and noise sources not specified in the test is assumed to be constant over subcarriers and time and shall be modelled as AWGN of appropriate power for Note 3: RSRP, SCH_RP and Io levels have been derived from other parameters for information purposes. They are not settable parameters themselves. Note 4: ETU70 propagation conditions are specified in Annex B.2 of 3GPP TS 36.101. |
|||
Note 2
to be fulfilled.A.8.7.1.2 Test Requirements
The UE shall send one Event 2B triggered measurement report for Cell2, with a measurement reporting delay less than 5.14 s from the beginning of time period T2.
The UE shall send one Event 3A triggered measurement report for Cell3, with a measurement reporting delay less than 8.23 s from the beginning of time period T2.
NOTE: The delay for interfrequency cell detection is equal to:
ms = 5143 ms
where:
is specified in 8.1.2.3.2 as 300 ms
is specified in 8.1.2.3.2 as 480 ms
and
is specified in 8.1.2.3.2 as 6 gaps of length 7 slots each, 28 ms
NOTE: The delay for interRAT cell detection is equal to:
= 8229 ms
where:
TBasic_Identify_E-UTRAN is specified in 8.1.2.6 as 480 ms
and
TE-UTRAN is specified in 8.1.2.6 as 6 gaps of length 7 slots each, 28 ms
A.8.7.2 Correct reporting of E-UTRA TDD neighbours in fading propagation condition
A.8.7.2.1 Test Purpose and Environment
The purpose of this test is to verify that the UE makes correct reporting of an event when doing inter frequency and E-UTRAN TDD measurements. The test will partly verify the requirements in section 8.1.2.3 and 8.1.2.6. The requirements are also applicable for a UE not requiring compressed mode for inter-frequency or inter-RAT E-UTRAN TDD measurements. In case a UE is not requiring compressed mode for inter-frequency measurements no compressed mode pattern with measurement purpose "FDD measurement" should be sent and in case a UE is not requiring compressed mode for inter-RAT E-UTRAN measurements no compressed mode pattern with measurement purpose "E-UTRAN measurements" should be sent for the parameters specified in table A8.33.
The test consists of two successive time periods, with time durations T1 and T2. The test parameters are given in tables A.8.33, A.8.34 and A.8.35 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2B and 3A shall be used.
Table A.8.33: General test parameters for Correct reporting of neighbours in Fading propagation condition
|
Parameter |
Unit |
Value |
Comment |
|
DCH parameters |
DL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.101 section A.3.1 |
|
|
Power Control |
On |
||
|
Compressed mode Interfrequency measurements E-UTRAN measurement |
DL compressed mode reference pattern 2, set 5 DL compressed mode reference pattern 2, set 5 |
Only applicable for UE requiring compressed mode patterns. As specified in table A.22 TS 25.101 section A.5 As specified in table A.22 TS 25.101 section A.5 |
|
|
Active cell |
Cell 1 |
||
|
Inter-RAT measurement quantity |
E-UTRAN RSRP |
||
|
Absolute Threshold (Ec/N0) used frequency |
dB |
-9 |
Ec/N0 threshold for Event 2b and 3a |
|
Absolute Threshold (Ec/N0) used for a not used frequency |
dB |
-18 |
Ec/IN0 threshold for Event 2b |
|
Threshold other system |
dBm |
-96 |
Absolute E-UTRA RSRP threshold for event 3a. |
|
Time to Trigger |
ms |
0 |
|
|
Filter coefficient |
0 |
||
|
Monitored cell list size |
Total 24 FDD neighbours 8 on frequency Channel 2 |
Measurement control information is sent before the compressed mode pattern starts. |
|
|
T1 |
s |
≥1 |
|
|
T2 |
s |
10 |
TableA.8.31: Cell Specific parameters for Correct reporting of neighbours in Fading propagation condition
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
||
|
T1 |
T2 |
T1 |
T2 |
||
|
UTRA RF Channel Number |
Channel 1 |
Channel 2 |
|||
|
CPICH_Ec/Ior |
dB |
-10 |
-10 |
||
|
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
||
|
SCH_Ec/Ior |
dB |
-12 |
-12 |
||
|
PICH_Ec/Ior |
dB |
-15 |
-15 |
||
|
DPCH_Ec/Ior |
dB |
Note 1 |
N/A |
||
|
OCNS |
Note 2 |
-0.941 |
|||
|
|
dB |
0 |
-Infinity |
-1.8 |
|
|
|
dBm/3,84 MHz |
-70 |
-70 |
||
|
CPICH_Ec/Io |
dB |
-13 |
-Infinity |
-14 |
|
|
Propagation Condition |
AWGN |
Case 5 as specified in Annex B of TS25.101 |
|||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior |
|||||
Table A.8.32: Cell specific test parameters for Correct reporting of E-UTRAN TDD neighbours in fading propagation condition (cell 3)
|
Parameter |
Unit |
Cell 3 |
|
|
T1 |
T2 |
||
|
E-UTRA RF Channel Number |
1 |
||
|
BWchannel |
MHz |
10 |
|
|
OCNG Pattern defined in A.3.2.2.2 in 3GPP TS 36.133 (OP.2 TDD) |
OP.2 TDD |
||
|
PBCH_RA |
dB |
0 |
|
|
PBCH_RB |
dB |
||
|
PSS_RA |
dB |
||
|
SSS_RA |
dB |
||
|
PCFICH_RB |
dB |
||
|
PHICH_RA |
dB |
||
|
PHICH_RB |
dB |
||
|
PDCCH_RA |
dB |
||
|
PDCCH_RB |
dB |
||
|
PDSCH_RA |
dB |
||
|
PDSCH_RB |
dB |
||
|
OCNG_RANote 1 |
dB |
||
|
OCNG_RBNote 1 |
dB |
||
|
|
dBm/15 kHz |
-98 |
|
|
|
dB |
-Infinity |
13 |
|
|
dB |
-Infinity |
13 |
|
RSRP Note 3 |
dBm/15 kHz |
-Infinity |
-85 |
|
SCH_RP Note 3 |
dBm/15 kHz |
-Infinity |
-85 |
|
Io Note 3 |
dBm/9 MHz |
-70.22 |
-57.01 |
|
Propagation Condition |
ETU70 (Note 4) |
||
|
Note 1: OCNG shall be used such that both cells are fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols. OCNG patterns are specified in annex A 3.2 of 3GPP TS 36.133. Note 2: Interference from other cells and noise sources not specified in the test is assumed to be constant over subcarriers and time and shall be modelled as AWGN of appropriate power for Note 3: RSRP, SCH_RP and Io levels have been derived from other parameters for information purposes. They are not settable parameters themselves. Note 4: ETU70 propagation conditions are specified in Annex B.2 of 3GPP TS 36.101. |
|||
Note 2
to be fulfilled.A.8.7.2.2 Test Requirements
The UE shall send one Event 2B triggered measurement report for Cell2, with a measurement reporting delay less than 5.14 s from the beginning of time period T2.
The UE shall send one Event 3A triggered measurement report for Cell3, with a measurement reporting delay less than 8.23 s from the beginning of time period T2.
NOTE: The delay for interfrequency cell detection is equal to:
ms = 5143 ms
where:
is specified in 8.1.2.3.2 as 300 ms
is specified in 8.1.2.3.2 as 480 ms
and
is specified in 8.1.2.3.2 as 6 gaps of length 7 slots each, 28 ms
NOTE: The delay for interRAT cell detection is equal to:
= 8229 ms
where:
TBasic_Identify_E-UTRAN is specified in 8.1.2.6 as 480 ms
and
TE-UTRAN is specified in 8.1.2.6 as 6 gaps of length 7 slots each, 28 ms