A.8.2A FDD adjacent frequency measurements
25.1333GPPRelease 17Requirements for support of radio resource management (FDD)TS
The test cases under A.8.2A are only applicable to UEs that do not require compressed mode to measure cells on a frequency adjacent to the intra-frequency.
A.8.2A.1 Event triggered reporting in AWGN propagation conditions
A.8.2A.1.1 Test Purpose and Environment
The purpose of this test is to verify that the UE makes correct reporting of an event. This test will partly verify the requirements in section 8.1.2 and 9.1.
The test parameters are given in Table A.8.12C and A.8.12D below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C and 2E shall be used. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. During time duration T1, the UE shall not have any timing information of cell 2.
Table A.8.12C: General test parameters for Event triggered reporting in AWGN propagation conditions
|
Parameter |
Unit |
Value |
Comment |
|
DCH parameters |
DL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.101 section A.3.1 |
|
|
Power Control |
On |
||
|
Active cell |
Cell 1 |
||
|
Threshold non used frequency |
dB |
-17 |
Absolute Ec/Io threshold for event 2C and 2E |
|
Hysteresis |
dB |
0 |
Applicable for event 2C and 2E |
|
W non-used frequency |
0 |
Applicable for event 2C and 2E |
|
|
Time to Trigger |
Ms |
0 |
Applicable for event 2C and 2E |
|
Filter coefficient |
0 |
Applicable for event 2C and 2E |
|
|
Monitored cell list size |
24 on channel 1 and 2 each |
||
|
T1 |
S |
5 |
|
|
T2 |
S |
5 |
|
|
T3 |
S |
5 |
Table A.8.12D: Cell specific test parameters for Event triggered reporting in AWGN propagation conditions
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||
|
UTRA RF Channel Number |
Channel 1 |
Channel 2 |
|||||
|
CPICH_Ec/Ior |
dB |
-10 |
-10 |
||||
|
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
||||
|
SCH_Ec/Ior |
dB |
-12 |
-12 |
||||
|
PICH_Ec/Ior |
dB |
-15 |
-15 |
||||
|
DPCH_Ec/Ior |
dB |
Note 1 |
N/A |
||||
|
OCNS |
Note 2 |
-0.941 |
|||||
|
|
dB |
0.02 |
0.02 |
0.02 |
-Infinity |
-1.80 |
-Infinity |
|
|
dBm/3,84 MHz |
-70 |
|||||
|
CPICH_Ec/Io |
dB |
-13 |
-13 |
-13 |
-Infinity |
-14 |
-Infinity |
|
Propagation Condition |
AWGN |
||||||
|
NOTE 1: The DPCH level is controlled by the power control loop NOTE 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . |
|||||||
A.8.2A.1.2 Test Requirements
a) The UE shall send one Event 2C triggered measurement report, with a measurement reporting delay less than 800 ms from the beginning of time period T2.
b) The UE shall send one Event 2E triggered measurement report, with a measurement reporting delay less than 200 ms from the beginning of time period T3.
c) The UE shall not send event triggered measurement reports, as long as the reporting criteria are not fulfilled.
The rate of correct events observed during repeated tests shall be at least 90%.
NOTE: The actual overall delays measured in the test may be up to 2 x TTIUL DCCH higher than the measurement reporting delays above because of TTI insertion uncertainty of the measurement report in the UL DCCH.
A.8.2A.2 Event triggered reporting of two detectable neighbours in AWGN propagation condition
A.8.2A.2.1 Test Purpose and Environment
The purpose of this test is to verify that the UE makes correct reporting of events. This test will partly verify the requirements in section 8.1.2 and 9.1.
The test parameters are given in Table A.8.12E and A.8.12F. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C and 2E shall be used and the periodical reporting of the events is not applied. The test consists of four successive time periods, with a time duration of T1, T2, T3 and T4 respectively. In the initial condition before the time T1 only Cell1 is active.
Table A.8.12E: General test parameters for Event triggered reporting of two detectable neighbours in AWGN propagation condition
|
Parameter |
Unit |
Value |
Comment |
|
DCH parameters |
DL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.101 section A.3.1 |
|
|
Power Control |
On |
||
|
Active cell |
Cell 1 |
||
|
Threshold non used frequency |
dB |
-16 |
Absolute Ec/Io threshold for event 2C and 2E |
|
Hysteresis |
dB |
0 |
Applicable for event 2C and 2E |
|
W non-used frequency |
0 |
Applicable for event 2C and 2E |
|
|
Time to Trigger |
Ms |
0 |
Applicable for event 2C and 2E |
|
Filter coefficient |
0 |
Applicable for event 2C and 2E |
|
|
Monitored cell list size |
32 |
||
|
T1 |
S |
10 |
|
|
T2 |
S |
10 |
|
|
T3 |
S |
10 |
|
|
T4 |
S |
10 |
Table A.8.12F: Cell specific test parameters for Event triggered reporting of two detectable neighbours in AWGN propagation condition
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
||||||||||||
|
T1 |
T2 |
T3 |
T4 |
T1 |
T2 |
T3 |
T4 |
T1 |
T2 |
T3 |
T4 |
|||||
|
UTRA RF Channel Number |
Channel 1 |
Channel 2 |
Channel 2 |
|||||||||||||
|
CPICH_Ec/Ior |
dB |
-10 |
-10 |
-10 |
||||||||||||
|
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
-12 |
||||||||||||
|
SCH_Ec/Ior |
dB |
-12 |
-12 |
-12 |
||||||||||||
|
PICH_Ec/Ior |
dB |
-15 |
-15 |
-15 |
||||||||||||
|
DPCH_Ec/Ior |
dB |
Note 1 |
N/A |
N/A |
||||||||||||
|
OCNS_Ec/Ior |
dB |
Note 2 |
-0.941 |
-0.941 |
||||||||||||
|
|
dB |
5.87 |
0.02 |
5.87 |
0.02 |
-Inf |
-0.06 |
20.33 |
-8.73 |
-6.65 |
-6.56 |
21.93 |
-12.23 |
|||
|
|
dBm/3,84 MHz |
-85 |
||||||||||||||
|
CPICH_Ec/Io |
dB |
-11 |
-13 |
-11 |
-13 |
-Inf |
-13.5 |
-13.9 |
-19.5 |
-17.5 |
-20 |
-12.3 |
-23 |
|||
|
Propagation Condition |
AWGN |
|||||||||||||||
|
NOTE 1: The DPCH level is controlled by the power control loop NOTE 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior |
||||||||||||||||
A.8.2A.2.2 Test Requirements
a) The UE may send one Event 2C triggered measurement report for Cell3, with a measurement reporting delay less than 800 ms from the beginning of time period T1, and send one Event 2E triggered measurement report for Cell3, with a measurement reporting delay less than 200ms from the beginning of time period T2.
b) The UE shall send one Event 2C triggered measurement report for Cell2, with a measurement reporting delay less than 800 ms from the beginning of time period T2.
c) The UE shall send one Event 2C triggered measurement report for Cell3, with a measurement reporting delay less than 200 ms from the beginning of time period T3.
d) The UE shall send one Event 2E triggered measurement report for Cell2, with a measurement reporting delay less than 200 ms from the beginning of time period T4.
d) The UE shall not send event triggered measurement reports, as long as the reporting criteria are not fulfilled.
The rate of correct events observed during repeated tests shall be at least 90%.
NOTE: The actual overall delays measured in the test may be up to 2 x TTIUL DCCH higher than the measurement reporting delays above because of TTI insertion uncertainty of the measurement report in the UL DCCH.
A.8.2A.3 Correct reporting of neighbours in fading propagation condition
A.8.2A.3.1 Test Purpose and Environment
The purpose of this test is to verify that the UE performs sufficient layer 1 filtering of the measurements, see section 9.1, which are the base for the event evaluation. The test is performed in fading propagation conditions. This test will partly verify the requirements in section 8.1.2.
The test parameters are given in Table A.8.12G and A.8.12H.In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C and Event 2E shall be used. The test consists of two successive time periods, each with a time duration of T1 and T2 respectively.
The TTI of the uplink DCCH shall be 20ms.
Table A.8.12G: General test parameters for correct reporting of neighbours in fading propagation condition
|
Parameter |
Unit |
Value |
Comment |
|
DCH parameters |
DL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.101 section A.3.1 |
|
|
Power Control |
On |
||
|
Active cell |
Cell 1 |
||
|
Threshold non used frequency for event 2C |
dB |
-12 |
Absolute Ec/Io threshold for event 2C |
|
Threshold non used frequency for event 2E |
dB |
-16 |
Absolute Ec/Io threshold for event 2E |
|
Hysteresis |
dB |
0 |
Applicable for event 2C and 2E |
|
W non-used frequency |
0 |
Applicable for event 2C and 2E |
|
|
Time to Trigger |
ms |
120 |
Applicable for event 2C and 2E |
|
Filter coefficient |
0 |
Applicable for event 2C and 2E |
|
|
Monitored cell list size |
24 |
Signalled before time T1. |
|
|
T1 |
s |
200 |
|
|
T2 |
s |
201 |
Table A.8.12H: Cell specific test parameters for correct reporting of neighbours in fading propagation condition
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
||
|
T1 |
T2 |
T1 |
T2 |
||
|
UTRA RF Channel Number |
Channel 1 |
Channel 2 |
|||
|
CPICH_Ec/Ior |
dB |
-10 |
-10 |
||
|
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
||
|
SCH_Ec/Ior |
dB |
-12 |
-12 |
||
|
PICH_Ec/Ior |
dB |
-15 |
-15 |
||
|
DPCH_Ec/Ior |
dB |
Note 1 |
N/A |
||
|
OCNS |
Note 2 |
-0.941 |
|||
|
|
dB |
2.32 |
-4.74 |
-4.74 |
2.32 |
|
|
dBm/3,84 MHz |
-70 |
|||
|
CPICH_Ec/Io |
dB |
-12 |
-16 |
-16 |
-12 |
|
Propagation Condition |
Case 5 as specified in Annex B of TS25.101 |
||||
|
NOTE 1: The DPCH level is controlled by the power control loop NOTE 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior |
|||||
A.8.2A.3.2 Test Requirements
a) The number of received event 2C reports for Cell 2 during time period T1 shall be less than 60.
b) During the first 1 s of time period T2 no event reports shall be counted.
c) The number of received event 2E reports for Cell 2 counted from 1s after the beginning of time period T2 until the end of time period T2 shall be less than 60.