A.5.5.2A Two frequencies present in the neighbour list and HS-DSCH DRX configured (Absolute priority levels not configured)
25.1333GPPRelease 17Requirements for support of radio resource management (FDD)TS
A.5.5.2A.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the cell re-selection delay in CELL_FACH state in section 5.5.2.1.2.
This scenario implies the presence of 2 carriers and 6 cells as given in tables A.5.4AA and A.5.4AB. The UE is requested to monitor neighbouring cells on 2 carriers. The maximum repetition period of the relevant system info blocks that needs to be received by the UE to camp on a cell shall be 1280 ms. Cell 1 and cell 2 shall belong to different Location Areas.
Table A.5.4AA: General test parameters for Cell Re-selection in Multi carrier case
Parameter |
Unit |
Value |
Comment |
|
Initial condition |
Active cell |
Cell2 |
||
Neighbour cells |
Cell1, Cell3,Cell4, Cell5, Cell6 |
|||
Final condition |
Active cell |
Cell1 |
||
Access Service Class (ASC#0) |
– |
1 |
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test. |
|
HCS |
Not used |
|||
HS-DSCH DRX cycleFACH |
frames |
8 |
DRX cycle length |
|
HS-DSCH Rx burstFACH |
frames |
1 |
On time during DRX cycle |
|
T321 |
msec |
100 |
Time before the DRX cycle is activated |
|
T1 |
s |
5 |
T1 need to be defined so that cell 1 and cell 2 are identified |
|
T2 |
s |
5 |
T2 need to be defined so that cell re-selection reaction time is taken into account. |
Table A.5.4AB: Cell re-selection multi carrier multi cell case
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
Cell 4 |
Cell 5 |
Cell 6 |
||||||
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
||
UTRA RF Channel Number |
Channel 1 |
Channel 2 |
Channel 1 |
Channel 1 |
Channel 2 |
Channel 2 |
|||||||
CPICH_Ec/Ior |
dB |
-10 |
-10 |
-10 |
-10 |
-10 |
-10 |
||||||
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
-12 |
-12 |
-12 |
-12 |
||||||
SCH_Ec/Ior |
dB |
-12 |
-12 |
-12 |
-12 |
-12 |
-12 |
||||||
PICH_Ec/Ior |
dB |
-15 |
-15 |
-15 |
-15 |
-15 |
-15 |
||||||
HS-PDSCH_Ec/Ior (Note 1) |
dB |
-10 |
-10 |
-10 |
-10 |
-10 |
-10 |
||||||
HS-SCCH1_Ec/Ior (Note 1) |
dB |
-13 |
-13 |
-13 |
-13 |
-13 |
-13 |
||||||
OCNS_Ec/Ior |
dB |
-1.837 |
-1.837 |
-1.837 |
-1.837 |
-1.837 |
-1.837 |
||||||
|
dB |
-3.4 |
2.2 |
2.2 |
-3.4 |
-7.4 |
-4.8 |
-7.4 |
-4.8 |
-4.8 |
-7.4 |
-4.8 |
-7.4 |
|
dBm / 3,84 MHz |
-70 |
|||||||||||
CPICH_Ec/Io |
dB |
-16 |
-13 |
-13 |
-16 |
-20 |
-20 |
-20 |
-20 |
||||
Propagation Condition |
AWGN |
||||||||||||
Cell_selection_and_ |
CPICH Ec/N0 |
CPICH Ec/N0 |
CPICH Ec/N0 |
CPICH Ec/N0 |
CPICH Ec/N0 |
CPICH Ec/N0 |
|||||||
Qqualmin |
dB |
-20 |
-20 |
-20 |
-20 |
-20 |
-20 |
||||||
Qrxlevmin |
dBm |
-115 |
-115 |
-115 |
-115 |
-115 |
-115 |
||||||
UE_TXPWR_MAX_ |
dB |
21 |
21 |
21 |
21 |
21 |
21 |
||||||
Qoffset2s, n |
dB |
C1, C2: 0 |
C2, C1: 0 |
C3, C1: 0 |
C4, C1: 0 |
C5, C1: 0 |
C6, C1: 0 |
||||||
Qhyst2 |
dB |
0 |
0 |
0 |
0 |
0 |
0 |
||||||
Treselection |
s |
0 |
0 |
0 |
0 |
0 |
0 |
||||||
Sintrasearch |
dB |
not sent |
not sent |
not sent |
not sent |
not sent |
not sent |
||||||
Sintersearch |
dB |
not sent |
not sent |
not sent |
not sent |
not sent |
not sent |
||||||
Note 1: The UE under test shall not be continuously scheduled to ensure that it operates in DRX when the reselection is being performed. The test equipment shall schedule with a different common H-RNTI when the UE under test is not being scheduled |
A.5.5.2A.2 Test Requirements
The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 1, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Location Registration on cell 1.
The cell re-selection delay shall be less than 2 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as: ,
where:
Tmeasurement,inter See section 8.4a.2.3.2 as 480 ms in this case
TIU 10msec
TSI Maximum repetition period of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.
TRA:TRA is a delay is caused by the physical random access procedure described in TS 25.214 section 6.1. A persistence value is assumed to be 1 in this test case and therefore TRA in this test case is 40 ms.
This gives a total of 1.83 s, allow 2s in the test case.