A.8.2C FDD detected set measurements
25.1333GPPRelease 17Requirements for support of radio resource management (FDD)TS
A.8.2C.1 Event triggered reporting of interfrequency detected set measurements with compressed mode
The test case under A.8.2C.1 is only applicable to a UE that is able to support inter frequency detected set CPICH measurements.
A.8.2C.1.1 Test Purpose and Environment
The purpose of this test is to verify that the UE makes correct reporting of an event when doing inter frequency detected set cell measurements. The test will partly verify the requirements in section 8.1.2.3.
The test consists of four successive time periods, T1, T2, T3 and T4 respectively. The test parameters are given in tables A.8.2C.1.1-1 and A.8.2C.1.1-2 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2B shall be used. The CPICH Ec/Io of the cell on the unused frequency shall be reported together with Event 2B reporting. Cell 2 shall not be included in the monitored cell list.
Table A.8.2C.1.1-1: General test parameters for correct reporting of inter-frequency detected cell with compressed mode
|
Parameter |
Unit |
Value |
Comment |
|
|
DCH parameters |
DL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.101 section A.3.1 |
||
|
Power Control |
On |
|||
|
Compressed mode |
Table A.22, set 4 |
As specified in TS 25.101 section A.5. |
||
|
Active cell |
Cell 1 |
On used frequency (RF Channel 1) |
||
|
Neighbor cell |
Cell 2 |
Non-used frequency (RF Channel 2) |
||
|
Absolute threshold (Ec/ Io) used frequency |
-13 |
Absolute Ec/ Io threshold for event 2B |
||
|
Absolute threshold (Ec/ Io) non used frequency |
dB |
-13 |
Absolute Ec/ Io threshold for event 2B |
|
|
Hysteresis |
dB |
0 |
||
|
Time to Trigger |
ms |
0 |
||
|
Filter coefficient |
0 |
|||
|
Propagation Condition |
Cell 1 |
AWGN |
||
|
Cell 2 |
Case 5 |
See Annex B of TS 25.101 |
||
|
DL DRX Active |
0 |
Downlink DRX is not used |
||
|
T1 |
s |
5 |
||
|
T2 |
s |
40 |
||
|
T3 |
s |
4 |
||
|
T4 |
s |
1 |
||
Table A.8.2C.1.1-2: Cell Specific parameters for correct reporting of inter-frequency detected cell with compressed mode
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
|||||||
|
T1 |
T2 |
T3 |
T4 |
T1 |
T2 |
T3 |
T4 |
|||
|
UTRA RF Channel Number |
Channel 1 |
Channel 2 |
||||||||
|
CPICH_Ec/Ior |
dB |
-10 |
-10 |
|||||||
|
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
|||||||
|
SCH_Ec/Ior |
dB |
-12 |
-12 |
|||||||
|
PICH_Ec/Ior |
dB |
-15 |
-15 |
|||||||
|
DPCH_Ec/Ior |
dB |
Note 1 |
N/A |
|||||||
|
OCNS |
Note 2 |
-0.941 |
||||||||
|
|
dB |
5.87 |
-4.74 |
5.87 |
-4.74 |
-Inf |
5.87 |
-4.74 |
5.87 |
|
|
|
dBm/3,84 MHz |
-70 |
||||||||
|
SCH _Ec/Io |
dB |
-13 |
-18 |
-13 |
-18 |
-Inf |
-13 |
-18 |
-13 |
|
|
CPICH_Ec/Io |
dB |
-11 |
-16 |
-11 |
-16 |
-Inf |
-11 |
-16 |
-11 |
|
|
Propagation Condition |
AWGN |
Case 5 |
||||||||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior |
||||||||||
A.8.2C.1.2 Test Requirements
a) The UE shall send one Event 2B triggered measurement report with the IE “Detected Set Trigger” set, with a measurement reporting delay less than 30 seconds from the beginning of time period T2.
b) The UE shall send one Event 2B triggered measurement report, with a measurement reporting delay less than 480 ms from the beginning of time period T4.
c) The UE shall not send event triggered measurement reports as long as the reporting criteria are not fulfilled.
The rate of correct events observed during repeated tests shall be at least 90% for each of the events in T2 and T4.
A.8.2C.2 Event triggered reporting of inter frequency detected set measurements without compressed mode
The test case under A.8.2C.1 is only applicable to a UE that is able to support inter frequency detected set CPICH measurements and to search inter-frequency measurements without compressed mode according to its measurement capability in the IE “Adjacent Frequency measurements without compressed mode”, the IE “Inter-band Frequency measurements without compressed mode”, or the IE “Enhanced inter-frequency measurements without compressed mode” defined in section 10.3.3.21 of TS 25.331 [16].
A.8.2C.2.1 Test Purpose and Environment
The purpose of this test is to verify that the UE makes correct reporting of an event when doing inter frequency detected set cell measurements. The test will partly verify the requirements in section 8.1.2.3.
The test consists of four successive time periods T1, T2, T3 and T4. The test parameters are given in tables A.8.2C.2.1-1 and A.8.2C.2.1-2 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2B shall be used. The CPICH Ec/Io of the cell on the unused frequency shall be reported together with Event 2B reporting. Cell 2 shall not be included in the monitored cell list.
Table A.8.2C.2.1-1: General test parameters for correct reporting of inter-frequency detected cell without compressed mode
|
Parameter |
Unit |
Value |
Comment |
|
|
DCH parameters |
DL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.101 section A.3.1 |
||
|
Power Control |
On |
|||
|
Active cell |
Cell 1 |
|||
|
Neighbor cell |
Cell 2 |
|||
|
Absolute threshold (Ec/Io) used frequency |
dB |
-13 |
Absolute Ec/Io threshold for event 2B |
|
|
Absolute threshold (Ec/Io) non used frequency |
dB |
-13 |
Absolute Ec/Io threshold for event 2B |
|
|
Hysteresis |
dB |
0 |
||
|
Time to Trigger |
ms |
0 |
||
|
Filter coefficient |
0 |
|||
|
Propagation Condition |
Cell 1 |
AWGN |
||
|
Cell 2 |
Case 5 |
See Annex B of TS 25.101 |
||
|
DL_DRX_Active |
0 |
Downlink DRX is not used |
||
|
T1 |
s |
5 |
||
|
T2 |
s |
40 |
||
|
T3 |
s |
4 |
||
|
T4 |
s |
1 |
||
Table A.8.2C.2.1-2: Cell Specific parameters for correct reporting of inter-frequency detected cell without compressed mode
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
||||||||
|
T1 |
T2 |
T3 |
T4 |
T1 |
T2 |
T3 |
T4 |
||||
|
UTRA RF Channel Number |
Channel 1 |
Channel 2 |
|||||||||
|
CPICH_Ec/Ior |
dB |
-10 |
-10 |
||||||||
|
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
||||||||
|
SCH_Ec/Ior |
dB |
-12 |
-12 |
||||||||
|
PICH_Ec/Ior |
dB |
-15 |
-15 |
||||||||
|
DPCH_Ec/Ior |
dB |
Note 1 |
N/A |
||||||||
|
OCNS |
Note 2 |
-0.941 |
|||||||||
|
|
dB |
5.87 |
-4.74 |
5.87 |
-4.74 |
-Inf |
5.87 |
-4.74 |
5.87 |
||
|
|
dBm/3.84 MHz |
-70 |
|||||||||
|
SCH _Ec/Io |
dB |
-13 |
-18 |
-13 |
-18 |
-Inf |
-13 |
-18 |
-13 |
||
|
CPICH_Ec/Io |
dB |
-11 |
-16 |
-11 |
-16 |
-Inf |
-11 |
-16 |
-11 |
||
|
Propagation Condition |
AWGN |
Case 5 |
|||||||||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior |
|||||||||||
