A.8.1 FDD intra frequency measurements
25.1333GPPRelease 17Requirements for support of radio resource management (FDD)TS
A.8.1.1 Event triggered reporting in AWGN propagation conditions
A.8.1.1.1 Test Purpose and Environment
The purpose of this test is to verify that the UE makes correct reporting of an event. This test will partly verify the requirements in section 8.1.2 and 9.1.
The test parameters are given in Table A.8.1 and A.8.2 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1A and 1B shall be used. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. During time duration T1, the UE shall not have any timing information of cell 2.
Table A.8.1: General test parameters for Event triggered reporting in AWGN propagation conditions
|
Parameter |
Unit |
Value |
Comment |
|
DCH parameters |
DL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.101 section A.3.1 |
|
|
Power Control |
On |
||
|
Active cell |
Cell 1 |
||
|
Reporting range |
dB |
3 |
Applicable for event 1A and 1B |
|
Hysteresis |
dB |
0 |
|
|
W |
1 |
Applicable for event 1A and 1B |
|
|
Reporting deactivation threshold |
0 |
Applicable for event 1A |
|
|
Time to Trigger |
ms |
0 |
|
|
Filter coefficient |
0 |
||
|
Monitored cell list size |
24 |
||
|
T1 |
s |
5 |
|
|
T2 |
s |
5 |
|
|
T3 |
s |
5 |
Table A.8.2: Cell specific test parameters for Event triggered reporting in AWGN propagation conditions
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||
|
CPICH_Ec/Ior |
dB |
-10 |
-10 |
||||
|
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
||||
|
SCH_Ec/Ior |
dB |
-12 |
-12 |
||||
|
PICH_Ec/Ior |
dB |
-15 |
-15 |
||||
|
DPCH_Ec/Ior |
dB |
Note 1 |
N/A |
||||
|
OCNS |
Note 2 |
-0.941 |
|||||
|
|
dB |
0 |
6.97 |
0 |
-Infinity |
5.97 |
-Infinity |
|
|
dBm/3,84 MHz |
-70 |
|||||
|
CPICH_Ec/Io |
dB |
-13 |
-13 |
-13 |
-Infinity |
-14 |
-Infinity |
|
Propagation Condition |
AWGN |
||||||
|
NOTE 1: The DPCH level is controlled by the power control loop NOTE 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . |
|||||||
A.8.1.1.2 Test Requirements
The UE shall send one Event 1A triggered measurement report, with a measurement reporting delay less than 800 ms from the beginning of time period T2.
The UE shall send one Event 1B triggered measurement report, with a measurement reporting delay less than 200 ms from the beginning of time period T3.
The UE shall not send event triggered measurement reports, as long as the reporting criteria are not fulfilled.
The rate of correct events observed during repeated tests shall be at least 90%.
NOTE: The actual overall delays measured in the test may be up to 2 x TTIUL DCCH higher than the measurement reporting delays above because of TTI insertion uncertainty of the measurement report in the UL DCCH.
A.8.1.2 Event triggered reporting of multiple neighbours in AWGN propagation condition
A.8.1.2.1 Test Purpose and Environment
The purpose of this test is to verify that the UE makes correct reporting of events. This test will partly verify the requirements in section 8.1.2 and 9.1.
The test parameters are given in Table A.8.3 and A.8.4. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1A, 1C and 1B shall be used and the periodical reporting of the events is not applied. The test consists of four successive time periods, with a time duration of T1, T2, T3 and T4 respectively. In the initial condition before the time T1 only Cell1 is active.
Table A.8.3: General test parameters for Event triggered reporting of multiple neighbours in AWGN propagation conditions
|
Parameter |
Unit |
Value |
Comment |
|
DCH parameters |
DL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.101 section A.3.1 |
|
|
Power Control |
On |
||
|
Active cell |
Cell 1 |
||
|
Reporting range |
dB |
3 |
Applicable for event 1A and 1B |
|
Hysteresis |
dB |
0 |
|
|
W |
1 |
Applicable for event 1A and 1B |
|
|
Replacement activation threshold |
0 |
Applicable for event 1C |
|
|
Reporting deactivation threshold |
0 |
Applicable for event 1A |
|
|
Time to Trigger |
ms |
0 |
|
|
Filter coefficient |
0 |
||
|
Monitored cell list size |
32 |
||
|
T1 |
S |
10 |
|
|
T2 |
S |
10 |
|
|
T3 |
S |
5 |
|
|
T4 |
S |
10 |
Table A.8.4: Cell specific test parameters for Event triggered reporting of multiple neighbours in AWGN propagation condition
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell3 |
||||||||||||||||||||||||||||||||||||||||
|
T1 |
T2 |
T3 |
T4 |
T1 |
T2 |
T3 |
T4 |
T1 |
T2 |
T3 |
T4 |
|||||||||||||||||||||||||||||||||
|
CPICH_Ec/Ior |
dB |
-10 |
-10 |
-10 |
||||||||||||||||||||||||||||||||||||||||
|
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
-12 |
||||||||||||||||||||||||||||||||||||||||
|
SCH_Ec/Ior |
dB |
-12 |
-12 |
-12 |
||||||||||||||||||||||||||||||||||||||||
|
PICH_Ec/Ior |
dB |
-15 |
-15 |
-15 |
||||||||||||||||||||||||||||||||||||||||
|
DPCH_Ec/Ior |
dB |
Note 1 |
N/A |
N/A |
||||||||||||||||||||||||||||||||||||||||
|
OCNS_Ec/Ior |
dB |
Note 2 |
-0.941 |
-0.941 |
||||||||||||||||||||||||||||||||||||||||
|
|
dB |
6.97 |
6.93 |
5.97 |
6.12 |
-Inf |
9.43 |
6.97 |
7.62 |
5.97 |
6.93 |
-Inf |
5.62 |
|||||||||||||||||||||||||||||||
|
|
dBm/3,84 MHz |
-85 |
||||||||||||||||||||||||||||||||||||||||||
|
CPICH_Ec/Io |
dB |
-13 |
-16 |
-14 |
-15.5 |
-Inf |
-13.5 |
-13 |
-14 |
-14 |
-16 |
-Inf |
-16 |
|||||||||||||||||||||||||||||||
|
Propagation Condition |
AWGN |
|||||||||||||||||||||||||||||||||||||||||||
|
NOTE 1: The DPCH level is controlled by the power control loop NOTE 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . |
||||||||||||||||||||||||||||||||||||||||||||
A.8.1.2.2 Test Requirements
a) The UE shall send one Event 1A triggered measurement report for Cell3, with a measurement reporting delay less than 800 ms from the beginning of time period T1.
b) The UE may send one Event 1C triggered measurement report for Cell3 after the beginning of the time period T1.
c) The UE shall send one Event 1C triggered measurement report for Cell2, with a measurement reporting delay less than 800 ms from the beginning of time period T2.
d) The UE shall send one Event 1A triggered measurement report for Cell2, with a measurement reporting delay less than 800 ms from the beginning of time period T2.
e) The UE shall send one Event 1B triggered measurement report for Cell3, with a measurement reporting delay less than 200 ms from the beginning of time period T3.
f) The UE shall send one Event 1A triggered measurement report for Cell3, with a measurement reporting delay less than 200 ms from the beginning of time period T4.
g) The UE may send one Event 1C triggered measurement report for Cell2 after the beginning of the time period T4.
h) The UE may send one Event 1C triggered measurement report for Cell3 after the beginning of the time period T4.
i) The UE shall not send event triggered measurement reports, as long as the reporting criteria are not fulfilled.
The rate of correct events observed during repeated tests shall be at least 90%.
NOTE: The actual overall delays measured in the test may be up to 2 x TTIUL DCCH higher than the measurement reporting delays above because of TTI insertion uncertainty of the measurement report in the UL DCCH.
A.8.1.3 Event triggered reporting of two detectable neighbours in AWGN propagation condition
A.8.1.3.1 Test Purpose and Environment
The purpose of this test is to verify that the UE makes correct reporting of events. This test will partly verify the requirements in section 8.1.2 and 9.1.
The test parameters are given in Table A.8.5 and A.8.6. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1A and 1B shall be used and the periodical reporting of the events is not applied. The test consists of four successive time periods, with a time duration of T1, T2, T3 and T4 respectively. In the initial condition before the time T1 only Cell1 is active.
Table A.8.5: General test parameters for Event triggered reporting of two detectable neighbours in AWGN propagation condition
|
Parameter |
Unit |
Value |
Comment |
|
DCH parameters |
DL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.101 section A.3.1 |
|
|
Power Control |
On |
||
|
Active cell |
Cell 1 |
||
|
Reporting range |
dB |
3 |
Applicable for event 1A and 1B |
|
Hysteresis |
dB |
0 |
|
|
W |
1 |
Applicable for event 1A and 1B |
|
|
Reporting deactivation threshold |
0 |
Applicable for event 1A |
|
|
Time to Trigger |
ms |
0 |
|
|
Filter coefficient |
0 |
||
|
Monitored cell list size |
32 |
||
|
T1 |
s |
10 |
|
|
T2 |
s |
10 |
|
|
T3 |
s |
10 |
|
|
T4 |
s |
10 |
Table A.8.6: Cell specific test parameters for Event triggered reporting of two detectable neighbours in AWGN propagation condition
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell3 |
||||||||||||||||||||||||||||||||||||||||
|
T1 |
T2 |
T3 |
T4 |
T1 |
T2 |
T3 |
T4 |
T1 |
T2 |
T3 |
T4 |
|||||||||||||||||||||||||||||||||
|
CPICH_Ec/Ior |
dB |
-10 |
-10 |
-10 |
||||||||||||||||||||||||||||||||||||||||
|
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
-12 |
||||||||||||||||||||||||||||||||||||||||
|
SCH_Ec/Ior |
dB |
-12 |
-12 |
-12 |
||||||||||||||||||||||||||||||||||||||||
|
PICH_Ec/Ior |
dB |
-15 |
-15 |
-15 |
||||||||||||||||||||||||||||||||||||||||
|
DPCH_Ec/Ior |
dB |
Note 1 |
N/A |
N/A |
||||||||||||||||||||||||||||||||||||||||
|
OCNS_Ec/Ior |
dB |
Note 2 |
-0.941 |
-0.941 |
||||||||||||||||||||||||||||||||||||||||
|
|
dB |
14.55 |
28.51 |
14.45 |
28.51 |
-Inf |
27.51 |
13.95 |
21.51 |
8.05 |
21.51 |
13.95 |
27.51 |
|||||||||||||||||||||||||||||||
|
|
dBm/3,84 MHz |
-85 |
||||||||||||||||||||||||||||||||||||||||||
|
CPICH_Ec/Io |
dB |
-11 |
-13 |
-14.5 |
-13 |
-Inf |
-14.0 |
-15 |
-20 |
-17.5 |
-20 |
-15 |
-14 |
|||||||||||||||||||||||||||||||
|
Propagation Condition |
AWGN |
|||||||||||||||||||||||||||||||||||||||||||
|
NOTE 1: The DPCH level is controlled by the power control loop NOTE 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior |
||||||||||||||||||||||||||||||||||||||||||||
A.8.1.3.2 Test Requirements
a) The UE shall send one Event 1A triggered measurement report for Cell2, with a measurement reporting delay less than 800 ms from the beginning of time period T2.
b) The UE shall send one Event 1A triggered measurement report for Cell3, with a measurement reporting delay less than 200 ms from the beginning of time period T3.
c) The UE shall send one Event 1B triggered measurement report for Cell2, with a measurement reporting delay less than 200 ms from the beginning of time period T4.
d) The UE shall not send event triggered measurement reports, as long as the reporting criteria are not fulfilled.
The rate of correct events observed during repeated tests shall be at least 90%.
NOTE: The actual overall delays measured in the test may be up to 2 x TTIUL DCCH higher than the measurement reporting delays above because of TTI insertion uncertainty of the measurement report in the UL DCCH.
A.8.1.4 Correct reporting of neighbours in fading propagation condition
A.8.1.4.1 Test Purpose and Environment
The purpose of this test is to verify that the UE performs sufficient layer 1 filtering of the measurements, see section 9.1, which are the base for the event evaluation. The test is performed in fading propagation conditions. This test will partly verify the requirements in section 8.1.2.
The test parameters are given in Table A.8.7 and A.8.8.In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1A and Event 1B shall be used. The test consists of two successive time periods, each with a time duration of T1 and T2 respectively.
The TTI of the uplink DCCH shall be 20ms.
Table A.8.7: General test parameters for correct reporting of neighbours in fading propagation condition
|
Parameter |
Unit |
Value |
Comment |
|
DCH parameters |
DL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.101 section A.3.1 |
|
|
Power Control |
On |
||
|
Active cell |
Cell 1 |
||
|
Reporting range |
dB |
0 |
Applicable for event 1A and 1B |
|
Hysteresis |
dB |
0 |
|
|
W |
1 |
Applicable for event 1A and 1B |
|
|
Reporting deactivation threshold |
0 |
Applicable for event 1A |
|
|
Time to Trigger |
ms |
120 |
|
|
Filter coefficient |
0 |
||
|
Monitored cell list size |
24 |
Signalled before time T1. |
|
|
T1 |
s |
200 |
|
|
T2 |
s |
201 |
Table A.8.8: Cell specific test parameters for correct reporting of neighbours in fading propagation condition
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
||
|
T1 |
T2 |
T1 |
T2 |
||
|
CPICH_Ec/Ior |
dB |
-10 |
-10 |
||
|
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
||
|
SCH_Ec/Ior |
dB |
-12 |
-12 |
||
|
PICH_Ec/Ior |
dB |
-15 |
-15 |
||
|
DPCH_Ec/Ior |
dB |
Note 1 |
N/A |
||
|
OCNS |
Note 2 |
-0.941 |
|||
|
|
dB |
7.29 |
3.29 |
3.29 |
7.29 |
|
|
dBm/3,84 MHz |
-70 |
|||
|
CPICH_Ec/Io |
dB |
-12 |
-16 |
-16 |
-12 |
|
Propagation Condition |
Case 5 as specified in Annex B of TS25.101 |
||||
|
NOTE 1: The DPCH level is controlled by the power control loop NOTE 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior |
|||||
A.8.1.4.2 Test Requirements
a) The number of received event 1A reports for Cell 2 during time period T1 shall be less than 60.
b) During the first 1 s of time period T2 no event reports shall be counted.
c) The number of received event 1B reports counted from 1s after the beginning of time period T2 until the end of time period T2 shall be less than 60.
A.8.1.5 Event triggered reporting of multiple neighbour cells in Case 1 fading condition
A.8.1.5.1 Test Purpose and Environment
The purpose of this test is to verify that the UE makes correct reporting of an event in Case1 fading propagation condition. This test will partly verify the requirements in section 8.1.2.
The test parameters are given in Table A.8.8A and A.8.8B below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1A shall be used and "CFN-SFN-Observed Time Difference" shall be reported. The test consists of two successive time periods, with time duration of T1 and T2, respectively. During time duration T1, the UE shall not have any timing information of invisible cells.
Table A.8.8A: General test parameters for event triggered reporting in multi-cell pedestrian environment
|
Parameter |
Unit |
Value |
Comment |
|
DCH parameters |
DL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.101 section A.3.1 |
|
|
Power Control |
On |
||
|
Active cells |
Cell2, Cell3, Cell4 |
||
|
Hysteresis |
dB |
0 |
Applicable for event 1A |
|
Time to Trigger |
ms |
0 |
Applicable for event 1A |
|
Filter coefficient |
0 |
Applicable for event 1A |
|
|
Reporting range R1a |
dB |
9 |
Applicable for event 1A |
|
W |
0 |
Applicable for event 1A |
|
|
TriggeringCondition |
activeSetAndMonitoredSetCells |
Applicable for event 1A |
|
|
Monitored cell list size |
32 |
||
|
T1 |
s |
5 |
|
|
T2 |
s |
5 |
Table 8.8B: Cell specific test parameters for event triggered reporting in multi-cell pedestrian environment
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
Cell 4 |
|||||||
|
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
|||||
|
UTRA RF Channel Number |
Channel 1 |
Channel 1 |
Channel 1 |
Channel 1 |
||||||||
|
CPICH_Ec/Ior |
dB |
-10 |
-10 |
-10 |
-10 |
|||||||
|
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
-12 |
-12 |
|||||||
|
SCH_Ec/Ior |
dB |
-12 |
-12 |
-12 |
-12 |
|||||||
|
PICH_Ec/Ior |
dB |
-15 |
-15 |
-15 |
-15 |
|||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
Note 1 |
Note 1 |
Note 1 |
|||||||
|
OCNS_Ec/Ior |
dB |
-0.941 |
Note 2 |
Note 2 |
Note 2 |
|||||||
|
|
dB |
-∞ |
1.3 |
4.3 |
1.3 |
4.3 |
1.3 |
1.3 |
4.3 |
|||
|
|
dBm/3,84 MHz |
‑70 |
||||||||||
|
Propagation Condition |
Case 1 (3km/h) |
|||||||||||
|
CPICH_Ec/Io |
dB |
-∞ |
-17.6 |
-14.6 |
-17.6 |
-14.6 |
-17.6 |
-17.6 |
-14.6 |
|||
|
|
dB |
-∞ |
-20.0 |
-17.0 |
-20.0 |
-17.0 |
-20.0 |
-20.0 |
-17.0 |
|||
|
NOTE 1: The DPCH level is controlled by the power control loop. NOTE 2: The power of the OCNS channel that is added shall make the total power equal to Ior. NOTE 3: CPICH_Ec/Io and SCH_Ec_maxpath/Io levels have been calculated from other parameters for information purposes. They are not settable themselves. |
||||||||||||
A.8.1.5.2 Test Requirements
The UE shall send one Event 1A triggered measurement report for Cell 1 with a measurement reporting delay less than 800 ms from the beginning of time period T2.
The rate of correct events observed during repeated tests shall be at least 90%.
NOTE: The actual overall delays measured in the test may be up to 2 x TTIUL DCCH higher than the measurement reporting delays above because of TTI insertion uncertainty of the measurement report in the UL DCCH.
A.8.1.6 Event triggered reporting of multiple neighbour cells in Case 3 fading condition
A.8.1.6.1 Test Purpose and Environment
The purpose of this test is to verify that the UE makes correct reporting of an event in Case3 fading propagation condition. This test will partly verify the requirements in section 8.1.2.
The test parameters are given in Table A.8.8C and A.8.8D below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1A and 1F shall be used and "CFN-SFN-Observed Time Difference" shall be reported. The test consists of two successive time periods, with time duration of T1 and T2 respectively. During time duration T1, the UE shall not have any timing information of invisible cells.
Table A.8.8C: General test parameters for event triggered reporting in multi-cell vehicular environment
|
Parameter |
Unit |
Value |
Comment |
|
DCH parameters |
DL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.101 section A.3.1 |
|
|
Power Control |
On |
||
|
Active cells |
Cell2, Cell3, Cell4 |
||
|
Hysteresis |
dB |
0 |
Applicable for event 1A |
|
Time to Trigger |
ms |
0 |
Applicable for event 1A |
|
Filter coefficient |
0 |
Applicable for event 1A and event 1F |
|
|
Reporting range R1a |
dB |
8 |
Applicable for event 1A |
|
W |
0 |
Applicable for event 1A |
|
|
TriggeringCondition |
activeSetAndMonitoredSetCells |
Applicable for event 1A |
|
|
Absolute threshold T1f |
dB |
–20 |
Applicable for event 1F |
|
Time to Trigger |
ms |
0 |
Applicable for event 1F |
|
TriggeringCondition |
activeSet |
Applicable for event 1F |
|
|
Monitored cell list size |
32 |
||
|
T1 |
s |
5 |
|
|
T2 |
s |
5 |
Table 8.8D: Cell specific test parameters for event triggered reporting in multi-cell vehicular environment
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
Cell 4 |
|||||
|
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
|||
|
UTRA RF Channel Number |
Channel 1 |
Channel 1 |
Channel 1 |
Channel 1 |
||||||
|
CPICH_Ec/Ior |
dB |
-10 |
-10 |
-10 |
-10 |
|||||
|
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
-12 |
-12 |
|||||
|
SCH_Ec/Ior |
dB |
-9.3 |
-9.3 |
-9.3 |
-9.3 |
|||||
|
PICH_Ec/Ior |
dB |
-15 |
-15 |
-15 |
-15 |
|||||
|
DPCH_Ec/Ior |
dB |
n.a. |
Note 1 |
Note 1 |
Note 1 |
|||||
|
OCNS_Ec/Ior |
dB |
Note 2 |
Note 2 |
Note 2 |
Note 2 |
|||||
|
|
dB |
-∞ |
1.1 |
3.6 |
4.6 |
3.6 |
4.6 |
6.6 |
-∞ |
|
|
|
dBm/3,84 MHz |
-70 |
||||||||
|
Propagation Condition |
Case 3 (120km/h) |
|||||||||
|
CPICH_Ec/Io |
dB |
-∞ |
-18.0 |
-16.5 |
-14.5 |
-16.5 |
-14.5 |
-13.5 |
-∞ |
|
|
|
dB |
-∞ |
-20.0 |
-18.5 |
-16.5 |
18.5 |
-16.5 |
-15.5 |
-∞ |
|
|
NOTE 1: The DPCH level is controlled by the power control loop. NOTE 2: The power of the OCNS channel that is added shall make the total power equal to Ior. NOTE 3: CPICH_Ec/Io, SCH_Ec_maxpath/Io, and |
||||||||||
levels have been calculated from other parameters for information purposes. They are not settable themselves.A.8.1.6.2 Test Requirements
The UE shall send an Event 1A triggered measurement report for Cell 1, with a measurement reporting delay less than 800 ms from the beginning of time period T2. The UE shall send an Event 1F triggered measurement report for Cell 4, with a measurement reporting delay less than 200 ms from the beginning of time period T2.
The rate of correct events 1A for Cell1 observed during repeated tests shall be at least 90%.
NOTE: The actual overall delays measured in the test may be up to 2 x TTIUL DCCH higher than the measurement reporting delays above because of TTI insertion uncertainty of the measurement report in the UL DCCH.
A.8.1.7 Event triggered reporting in AWGN propagation conditions
A.8.1.7.1 Test Purpose and Environment
The purpose of this test is to verify that the UE makes correct reporting of an event when UE DRX is active. This test will partly verify the requirements in section 8.1.2 and 9.1, and is applicable to all UE that support DRX in cell DCH state.
The test parameters are given in Table A.8.8A and A.8.8B below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1A shall be used. The test consists of two successive time periods, with a time duration of T1and T2 respectively. During time duration T1, the UE shall not have any timing information of cell 2.
Table A.8.8A: General test parameters for Event triggered reporting in AWGN propagation conditions when UE DRX is active
|
Parameter |
Unit |
Value |
Comment |
|
DCH parameters |
DL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.101 section A.3.1 |
|
|
Power Control |
On |
||
|
Active cell |
Cell 1 |
||
|
Reporting range |
dB |
3 |
Applicable for event 1A |
|
Hysteresis |
dB |
0 |
|
|
W |
1 |
Applicable for event 1A |
|
|
Reporting deactivation threshold |
0 |
Applicable for event 1A |
|
|
Time to Trigger |
ms |
0 |
|
|
Filter coefficient |
0 |
||
|
Monitored cell list size |
24 |
||
|
UE DRX cycle |
sub-frames |
20 |
Length of the UE DRX cycle. Note: UE DRX cycle 1 is used. |
|
Inactivity Threshold for UE DRX cycle 1 |
sub-frames |
1 |
|
|
UE DRX Grant Monitoring |
Boolean |
FALSE |
|
|
E-DCH TTI |
ms |
2 |
|
|
UE DTX cycle 1 |
sub-frames |
20 |
|
|
UE DTX cycle 2 |
sub-frames |
20 |
|
|
CQI DTX Timer |
sub-frames |
4 |
|
|
UE DPCCH burst 1 |
sub-frames |
2 |
|
|
UE DPCCH burst 2 |
sub-frames |
2 |
|
|
Inactivity Threshold for UE DTX cycle 2 |
Number of E-DCH TTIs |
1 |
|
|
UE DTX long preamble length |
Number of slots |
2 |
Note: Mandatory Default value is used. |
|
MAC Inactivity Threshold |
Number of E-DCH TTIs |
Infinity |
|
|
Uplink DPCCH slot format |
1 |
||
|
T1 |
s |
5 |
|
|
T2 |
s |
5 |
Table A.8.8B: Cell specific test parameters for Event triggered reporting in AWGN propagation conditions when UE DRX is active.
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
||
|
T1 |
T2 |
T1 |
T2 |
||
|
CPICH_Ec/Ior |
dB |
-10 |
-10 |
||
|
PCCPCH_Ec/Ior |
dB |
-12 |
-12 |
||
|
SCH_Ec/Ior |
dB |
-12 |
-12 |
||
|
PICH_Ec/Ior |
dB |
-15 |
-15 |
||
|
DPCH_Ec/Ior |
dB |
Note 1 |
N/A |
||
|
HS-PDSCH_Ec/Ior |
dB |
-10 |
N/A |
||
|
HS-SCCH-1_Ec/Ior |
dB |
-13 |
N/A |
||
|
OCNS |
Note 2 |
-0.941 |
|||
|
|
dB |
0 |
6.97 |
-Infinity |
5.97 |
|
|
dBm/3,84 MHz |
-70 |
|||
|
CPICH_Ec/Io |
dB |
-13 |
-13 |
-Infinity |
-14 |
|
Propagation Condition |
AWGN |
||||
|
NOTE 1: The DPCH level is controlled by the power control loop NOTE 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . NOTE 3: The UE under test is not continuously scheduled, and shall not be configured to continuously transmit data, to enable it to use DRX and DTX. |
|||||
A.8.1.7.2 Test Requirements
The UE shall send one Event 1A triggered measurement report, with a measurement reporting delay less than 1.5 s from the beginning of time period T2.
The UE shall not send event triggered measurement reports, as long as the reporting criteria are not fulfilled.
The rate of correct events observed during repeated tests shall be at least 90%.
NOTE: The actual overall delays measured in the test may be up to 2 x TTIUL DCCH higher than the measurement reporting delays above because of TTI insertion uncertainty of the measurement report in the UL DCCH.