A.5.5.5 UTRAN to E-UTRA Cell Reselection
25.1333GPPRelease 17Requirements for support of radio resource management (FDD)TS
A.5.5.5.1 Reselection to E-UTRA FDD when HS-DSCH DRX is configured (E-UTRA has higher priority)
A.5.5.5.1.1 Test Purpose and Environment
This test is to verify the requirement for the UTRA FDD to E-UTRA FDD inter-RAT cell reselection delay reported in section 5.5.2.1.5
The test scenario comprises two different cells, with cell 1 being the UTRA serving cell and cell 2 being the E-UTRA cell to be re-selected to. Test parameters are given in Tables A.5.4L, A.5.4M, A.5.4N. The test consists of two successive time periods, with time duration of T1, T2. UTRA cell 1 is already identified by the UE prior to the start of the test. Cell 2 is of higher priority than cell 1.
Cell 1 and cell 2 shall belong to different tracking areas. Furthermore, UE has not registered with network for the tracking area containing cell 2.
CELL_FACH with discontinuous HS-DSCH reception should be configured. The UE should not be scheduled with HS-DSCH data during T1 and T2 such that the DRX cycle becomes active
Table A.5.4L: General test parameters for UTRAN to E-UTRA Cell Reselection
|
Parameter |
Unit |
Value |
Comment |
|
|
Initial condition |
Active cell |
Cell1 |
||
|
T2 end condition |
Active cell |
Cell2 |
UE shall perform reselection to cell 2 during T2 |
|
|
Neighbour cell |
Cell1 |
|||
|
HS-DSCH DRX cycleFACH |
frames |
8 |
Length of the DRX cycle |
|
|
HS-DSCH Rx burstFACH |
frames |
1 |
On time during DRX cycle |
|
|
T321 |
msec |
100 |
Number of seconds until the DRX cycle is initiated |
|
|
HCS |
Not used |
|||
|
E-UTRA PRACH configuration |
4 |
As specified in table 5.7.1-2 in TS 36.211 |
||
|
E-UTRA access barring information |
Not sent |
No additional delays in random access procedure |
||
|
T1 |
s |
>70 |
During T1, cell 2 shall be powered off, and during the off time its physical cell identity shall be changed. The intention is to ensure that cell 2 has not been detected by the UE prior to the start of period T2. |
|
|
T2 |
s |
70 |
T2 needs to be defined so that cell re-selection reaction time is taken into account. |
|
Table A.5.4M: Cell specific test parameters for UTRAN to E-UTRA cell reselection (cell 1)
|
Parameter |
Unit |
Cell 1 (UTRA) |
||||
|
T1 |
T2 |
|||||
|
UTRA RF Channel Number |
Channel 1 |
|||||
|
CPICH_Ec/Ior |
dB |
-10 |
||||
|
PCCPCH_Ec/Ior |
dB |
-12 |
||||
|
SCH_Ec/Ior |
dB |
-12 |
||||
|
PICH_Ec/Ior |
dB |
-15 |
||||
|
HS-PSDCH_Ec/Ior (Note 2) |
dB |
-10 |
||||
|
HS-SCCH_Ec/Ior (Note 2) |
dB |
-13 |
||||
|
OCNS_Ec/Ior |
dB |
-1.1837 |
||||
|
|
dB |
13 |
13 |
|||
|
|
dBm/3,84 MHz |
‑70 |
||||
|
CPICH_Ec/Io |
dB |
-10.21 |
-10.21 |
|||
|
CPICH_RSCP |
dBm |
-67 |
-67 |
|||
|
Qqualmin |
dB |
-20 |
||||
|
Qrxlevmin |
dBm |
-115 |
||||
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
||||
|
Treselection |
s |
0 |
||||
|
Sprioritysearch1 |
dB |
42 |
||||
|
Sprioritysearch2 |
dB |
0 |
||||
|
SsearchE-UTRA |
dB |
Not sent |
||||
|
Threshx, high (Note 1) |
dB |
48 |
||||
|
Propagation Condition |
AWGN |
|||||
|
Note 1: This refers to the value of Threshx, high which is included in UTRA system information, and is a threshold for the E-UTRA target cell. Note 2: The UE under test shall not be continuously scheduled to ensure that it operates in DRX when the reselection is being performed. The test equipment shall schedule with a different common H-RNTI when the UE under test is not being scheduled |
||||||
Table A.5.4N: Cell specific test parameters for UTRAN to E-UTRA cell reselection (cell 2)
|
Parameter |
Unit |
Cell 2 |
|
|
T1 |
T2 |
||
|
E-UTRA RF Channel number |
2 |
||
|
BWchannel |
MHz |
10 |
|
|
OCNG Patterns defined in TS 36.133 A.3.2.1.2 (OP.2 FDD) [24] |
OP.2 FDD |
||
|
PBCH_RA |
dB |
0 |
|
|
PBCH_RB |
dB |
||
|
PSS_RA |
dB |
||
|
SSS_RA |
dB |
||
|
PCFICH_RB |
dB |
||
|
PHICH_RA |
dB |
||
|
PHICH_RB |
dB |
||
|
PDCCH_RA |
dB |
||
|
PDCCH_RB |
dB |
||
|
PDSCH_RA |
dB |
||
|
PDSCH_RB |
dB |
||
|
OCNG_RANote 1 |
dB |
||
|
OCNG_RBNote 1 |
dB |
||
|
Qrxlevmin |
dBm |
-140 |
|
|
|
dBm/15 kHz |
-98 |
|
|
RSRP |
dBm/15 KHz |
-infinity |
-86 |
|
|
dB |
-infinity |
12 |
|
|
dB |
-infinity |
12 |
|
TreselectionEUTRAN |
s |
0 |
|
|
Snonintrasearch |
dB |
Not sent |
|
|
Threshserving, low |
dB |
44 |
|
|
Threshx, low (Note 2) |
dB |
42 |
|
|
Propagation Condition |
AWGN |
||
|
Note 1: OCNG shall be used such that cell 2 is fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols. Note 2: This refers to the value of Threshx, low which is included in E-UTRA system information, and is a threshold for the UTRA target cell. |
|||
A.5.5.5.1.2 Test Requirements
The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on Cell 2.
The cell re-selection delay shall be less than 66 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as: 
, where:
TSI = the maximum time allowed aquire system information from a E-UTRAN cell, 1280msec [24].
TRA = the additional delay caused by the random access procedure, 30msec [24]
TIdentify,,E-UTRAN = Time to identify an E-UTRA cell, as defined in section 8.4a.2.6.1
Thigher_priority_search is described in section 4.2.2
This gives a total of 67.7, allow 66 s in the test case.
A.5.5.5.2 Reselection to E-UTRA FDD when HS-DSCH DRX is configured (E-UTRA has lower priority)
A.5.5.5 2.1 Test Purpose and Environment
This test is to verify the requirement for the UTRAN to E-UTRAN cell reselection delay reported in section 5.5.2.1.5.
This scenario implies the presence of 1 UTRAN serving cell, and 1 E-UTRAN cell to be re-selected. The UE is requested to monitor neighbouring cells on 1 UTRAN carrier and 1 E-UTRAN carrier. Test parameters are given in Table, A.5.4O, A.5.4P, A.5.4Q. The test consists of two successive time periods, with time duration of T1 and T2, respectively. Both UTRA cell 1 and E-UTRA cell 2 are already identified by the UE prior to the start of the test. Cell 2 is of lower priority than cell 1. Cell 1 and cell 2 shall belong to different tracking areas.
CELL_FACH with discontinuous HS-DSCH reception and with only the first DRX cycle active should be configured. The UE should not be scheduled with HS-DSCH data during T1 and T2 such that the DRX cycle becomes active.
Table A.5.4O: General test parameters for UTRAN to E-UTRAN Cell Re-selection
|
Parameter |
Unit |
Value |
Comment |
|
|
Initial condition |
Active cell |
Cell 1 |
UTRAN cell |
|
|
Neighbour cell |
Cell 2 |
E-UTRAN cell |
||
|
Final condition |
Active cell |
Cell 2 |
UE shall perform reselection to cell 2 during T2 |
|
|
HS-DSCH DRX cycleFACH |
frames |
8 |
DRX cycle length |
|
|
HS-DSCH Rx burstFACH |
frames |
1 |
On time during DRX cycle |
|
|
T321 |
msec |
100 |
Time before the DRX cycle is activated |
|
|
E-UTRA PRACH configuration |
4 |
As specified in table 5.7.1-2 in TS 36.211 |
||
|
E-UTRA access barring information |
Not sent |
No additional delays in random access procedure |
||
|
T1 |
s |
>20 |
T1 need to be defined so that cell re-selection reaction time is taken into account. |
|
|
T2 |
s |
7 |
T2 need to be defined so that cell re-selection reaction time is taken into account. |
|
Table A.5.4P: Cell re-selection UTRAN to E-UTRAN cell case (cell 1)
|
Parameter |
Unit |
Cell 1 (UTRA) |
||
|
T1 |
T2 |
|||
|
UTRA RF Channel Number |
Channel 1 |
|||
|
CPICH_Ec/Ior |
dB |
-10 |
||
|
PCCPCH_Ec/Ior |
dB |
-12 |
||
|
SCH_Ec/Ior |
dB |
-12 |
||
|
PICH_Ec/Ior |
dB |
-15 |
||
|
HS-PDSCH_Ec/Ior (Note 2) |
dB |
-10 |
||
|
HS-SCCH1_Ec/Ior (Note 2) |
dB |
-13 |
||
|
OCNS_Ec/Ior |
dB |
-1.837 |
||
|
|
dB |
11 |
-5 |
|
|
|
dBm/3,84 MHz |
-70 |
||
|
CPICH_Ec/Io |
dB |
-10.33 |
-16.19 |
|
|
CPICH_RSCP |
dBm |
-69 |
-85 |
|
|
Propagation Condition |
AWGN |
|||
|
Cell_selection_and_ |
CPICH Ec/N0 |
|||
|
Qqualmin |
dB |
-20 |
||
|
Qrxlevmin |
dBm |
-115 |
||
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
||
|
Qhyst1 |
dB |
0 |
||
|
Treselection |
s |
0 |
||
|
Sprioritysearch1 |
dB |
62 |
||
|
Sprioritysearch2 |
dB |
0 |
||
|
Threshserving, low |
dB |
36 |
||
|
Threshx, low (Note 1) |
dB |
50 |
||
|
Note 1: This refers to the value of Threshx, low which is included in UTRA system information, and is a threshold for the E-UTRA target cell. Note 2: The UE under test shall not be continuously scheduled to ensure that it operates in DRX when the reselection is being performed. The test equipment shall schedule with a different common H-RNTI when the UE under test is not being scheduled |
||||
Table A.5.4Q: Cell re-selection UTRAN to E-UTRAN cell case (cell 2)
|
Parameter |
Unit |
Cell 2 (E-UTRA) |
|
|
T1 |
T2 |
||
|
E-UTRA RF Channel number |
1 |
||
|
BWchannel |
MHz |
10 |
|
|
OCNG Patterns defined in A.3.2.1.1 (OP.2 FDD) |
OP.2 FDD |
||
|
PBCH_RA |
dB |
0 |
|
|
PBCH_RB |
dB |
||
|
PSS_RA |
dB |
||
|
SSS_RA |
dB |
||
|
PCFICH_RB |
dB |
||
|
PHICH_RA |
dB |
||
|
PHICH_RB |
dB |
||
|
PDCCH_RA |
dB |
||
|
PDCCH_RB |
dB |
||
|
PDSCH_RA |
dB |
||
|
PDSCH_RB |
dB |
||
|
OCNG_RANote 1 |
dB |
||
|
OCNG_RBNote 1 |
dB |
||
|
Qrxlevmin |
dBm |
-140 |
|
|
|
dBm/15 kHz |
-98 |
|
|
RSRP |
dBm/15 KHz |
-84 |
-84 |
|
|
dB |
14 |
14 |
|
|
dB |
14 |
14 |
|
TreselectionEUTRAN |
s |
0 |
|
|
Snonintrasearch |
dB |
50 |
|
|
Threshx, high |
dB |
40 |
|
|
Propagation Condition |
AWGN |
||
|
Note 1: OCNG shall be used such that cell 2 is fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols. Note 2: This refers to the value of Threshx, high which is included in E-UTRA system information, and is a threshold for the UTRA target cell. |
|||
A.5.5.5.2.2 Test Requirements
The cell reselection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on Cell 2.
The cell re-selection delay shall be less than 5.7 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
, where:
TSI = the maximum time allowed aquire system information from a E-UTRAN cell, 1280msec [24].
TRA = the additional delay caused by the random access procedure, 30msec [24]
TIdentify,,E-UTRAN = Time to identify an E-UTRA cell, as defined in section 8.4a.2.6.1
This gives a total of 5.61 s, allow 5.7 s in the test case.
A.5.5.5.3 Reselection to E-UTRA FDD when HS-DSCH 2nd DRX is configured (E-UTRA has higher priority)
A.5.5.5.3.1 Test Purpose and Environment
This test is to verify the requirement for the UTRA FDD to E-UTRA FDD inter-RAT cell reselection delay reported in section 5.5.2.1.5
The test scenario comprises two different cells, with cell 1 being the UTRA serving cell and cell 2 being the E-UTRA cell to be re-selected to. Test parameters are given in Tables A.5.4R, A.5.4S, A.5.4T. The test consists of two successive time periods, with time duration of T1, T2. UTRA cell 1 is already identified by the UE prior to the start of the test. Cell2 shall have higher priority than Cell 1.
Cell 1 and cell 2 shall belong to different tracking areas. Furthermore, UE has not registered with network for the tracking area containing cell 2.
CELL_FACH with discontinuous HS-DSCH reception and 2nd DRX cycle should be configured. The UE should not be scheduled with HS-DSCH data during T1 and T2 such that the DRX cycle becomes active.
Table A.5.4R: General test parameters for UTRAN to E-UTRA Cell Reselection
|
Parameter |
Unit |
Value |
Comment |
|
|
Initial condition |
Active cell |
Cell1 |
||
|
T2 end condition |
Active cell |
Cell2 |
UE shall perform reselection to cell 2 during T2 |
|
|
Neighbour cell |
Cell1 |
|||
|
HS-DSCH second DRX cycleFACH |
frames |
512 |
Length of the DRX cycle |
|
|
HS-DSCH second Rx burstFACH |
frames |
1 |
On time during DRX cycle |
|
|
T329 |
msec |
500 |
Number of seconds until the DRX cycle is initiated |
|
|
DRX level |
Single level DRX |
Second DRX only active |
||
|
HCS |
Not used |
|||
|
E-UTRA PRACH configuration |
4 |
As specified in table 5.7.1-2 in TS 36.211 |
||
|
E-UTRA access barring information |
Not sent |
No additional delays in random access procedure |
||
|
T1 |
s |
>20 |
During T1, cell 2 shall be powered off, and during the off time its physical cell identity shall be changed. The intention is to ensure that cell 2 has not been detected by the UE prior to the start of period T2. |
|
|
T2 |
s |
70 |
T2 needs to be defined so that cell re-selection reaction time is taken into account. |
|
Table A.5.4S: Cell specific test parameters for UTRAN to E-UTRA cell reselection (cell 1)
|
Parameter |
Unit |
Cell 1 (UTRA) |
||||
|
T1 |
T2 |
|||||
|
UTRA RF Channel Number |
Channel 1 |
|||||
|
CPICH_Ec/Ior |
dB |
-10 |
||||
|
PCCPCH_Ec/Ior |
dB |
-12 |
||||
|
SCH_Ec/Ior |
dB |
-12 |
||||
|
PICH_Ec/Ior |
dB |
-15 |
||||
|
HS-PDSCH_Ec/Ior (Note 2) |
dB |
-10 |
||||
|
HS-SCCH1_Ec/Ior (Note 2) |
dB |
-13 |
||||
|
OCNS_Ec/Ior |
dB |
-1.837 |
||||
|
|
dB |
13 |
13 |
|||
|
|
dBm/3,84 MHz |
‑70 |
||||
|
CPICH_Ec/Io |
dB |
-10.21 |
-10.21 |
|||
|
CPICH_RSCP |
dBm |
-67 |
-67 |
|||
|
Qqualmin |
dB |
-20 |
||||
|
Qrxlevmin |
dBm |
-115 |
||||
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
||||
|
Treselection |
s |
0 |
||||
|
Sprioritysearch1 |
dB |
42 |
||||
|
Sprioritysearch2 |
dB |
0 |
||||
|
SsearchE-UTRA |
dB |
Not sent |
||||
|
Threshx, high (Note 1) |
dB |
48 |
||||
|
Propagation Condition |
AWGN |
|||||
|
Note 1: This refers to the value of Threshx, high which is included in UTRA system information, and is a threshold for the E-UTRA target cell. Note 2: The UE under test shall not be continuously scheduled to ensure that it operates in DRX when the reselection is being performed. The test equipment shall schedule with a different common H-RNTI when the UE under test is not being scheduled |
||||||
Table A.5.4T: Cell specific test parameters for UTRAN to E-UTRA cell reselection (cell 2)
|
Parameter |
Unit |
Cell 2 |
|
|
T1 |
T2 |
||
|
E-UTRA RF Channel number |
2 |
||
|
BWchannel |
MHz |
10 |
|
|
OCNG Patterns defined in TS 36.133 A.3.2.1.2 (OP.2 FDD) [24] |
OP.2 FDD |
||
|
PBCH_RA |
dB |
0 |
|
|
PBCH_RB |
dB |
||
|
PSS_RA |
dB |
||
|
SSS_RA |
dB |
||
|
PCFICH_RB |
dB |
||
|
PHICH_RA |
dB |
||
|
PHICH_RB |
dB |
||
|
PDCCH_RA |
dB |
||
|
PDCCH_RB |
dB |
||
|
PDSCH_RA |
dB |
||
|
PDSCH_RB |
dB |
||
|
OCNG_RANote 1 |
dB |
||
|
OCNG_RBNote 1 |
dB |
||
|
Qrxlevmin |
dBm |
-140 |
|
|
|
dBm/15 kHz |
-98 |
|
|
RSRP |
dBm/15 KHz |
-infinity |
-86 |
|
|
dB |
-infinity |
12 |
|
|
dB |
-infinity |
12 |
|
TreselectionEUTRAN |
s |
0 |
|
|
Snonintrasearch |
dB |
Not sent |
|
|
Threshserving, low |
dB |
44 |
|
|
Threshx, low (Note 2) |
dB |
42 |
|
|
Propagation Condition |
AWGN |
||
|
Note 1: OCNG shall be used such that cell 2 is fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols. Note 2: This refers to the value of Threshx, low which is included in E-UTRA system information, and is a threshold for the UTRA target cell. |
|||
A.5.5.5.3.2 Test Requirements
The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on Cell 2.
The cell re-selection delay shall be less than 66 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as: 
, where:
TSI = the maximum time allowed aquire system information from a E-UTRAN cell, 1280msec [24].
TRA = the additional delay caused by the random access procedure, 30msec [24]
TIdentify,,E-UTRAN = Time to identify an E-UTRA cell, as defined in section 8.4a.2.6.1
Thigher_priority_search is described in section 4.2.2
This gives a total of 65.67, allow 66 s in the test case.
A.5.5.5.4 Reselection to E-UTRA TDD when HS-DSCH DRX is configured (E-UTRA has higher priority)
A.5.5.5.4.1 Test Purpose and Environment
This test is to verify the requirement for the UTRA FDD to E-UTRA TDD inter-RAT cell reselection delay reported in section 5.5.2.1.5
The test scenario comprises two different cells, with cell 1 being the UTRA serving cell and cell 2 being the E-UTRA cell to be re-selected to. Test parameters are given in Tables A.5.4U, A.5.4V, A.5.4W. The test consists of two successive time periods, with time duration of T1, T2. UTRA cell 1 is already identified by the UE prior to the start of the test. Cell 2 is of higher priority than cell 1.
Cell 1 and cell 2 shall belong to different tracking areas. Furthermore, UE has not registered with network for the tracking area containing cell 2.
CELL_FACH with discontinuous HS-DSCH reception should be configured. The UE should not be scheduled with HS-DSCH data during T1 and T2 such that the DRX cycle becomes active.
Table A.5.4U: General test parameters for UTRAN to E-UTRA Cell Reselection
|
Parameter |
Unit |
Value |
Comment |
|
|
Initial condition |
Active cell |
Cell1 |
||
|
T2 end condition |
Active cell |
Cell2 |
UE shall perform reselection to cell 2 during T2 |
|
|
Neighbour cell |
Cell1 |
|||
|
HS-DSCH DRX cycleFACH |
frames |
8 |
Length of the DRX cycle |
|
|
HS-DSCH Rx burstFACH |
frames |
1 |
On time during DRX cycle |
|
|
T321 |
msec |
100 |
Number of seconds until the DRX cycle is initiated |
|
|
HCS |
Not used |
|||
|
E-UTRA PRACH configuration |
4 |
As specified in table 5.7.1-2 in TS 36.211 |
||
|
E-UTRA access barring information |
Not sent |
No additional delays in random access procedure |
||
|
T1 |
s |
>70 |
During T1, cell 2 shall be powered off, and during the off time its physical cell identity shall be changed. The intention is to ensure that cell 2 has not been detected by the UE prior to the start of period T2. |
|
|
T2 |
s |
70 |
T2 needs to be defined so that cell re-selection reaction time is taken into account. |
|
Table A.5.4V: Cell specific test parameters for UTRAN to E-UTRA TDD cell reselection (cell 1)
|
Parameter |
Unit |
Cell 1 (UTRA) |
||||
|
T1 |
T2 |
|||||
|
UTRA RF Channel Number |
Channel 1 |
|||||
|
CPICH_Ec/Ior |
dB |
-10 |
||||
|
PCCPCH_Ec/Ior |
dB |
-12 |
||||
|
SCH_Ec/Ior |
dB |
-12 |
||||
|
PICH_Ec/Ior |
dB |
-15 |
||||
|
HS-PDSCH_Ec/Ior |
dB |
-10 |
||||
|
HS-SCCH1_Ec/Ior |
dB |
-13 |
||||
|
OCNS_Ec/Ior |
dB |
-1.837 |
||||
|
|
dB |
13 |
13 |
|||
|
|
dBm/3,84 MHz |
‑70 |
||||
|
CPICH_Ec/Io |
dB |
-10.21 |
-10.21 |
|||
|
CPICH_RSCP |
dBm |
-67 |
-67 |
|||
|
Qqualmin |
dB |
-20 |
||||
|
Qrxlevmin |
dBm |
-115 |
||||
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
||||
|
Treselection |
s |
0 |
||||
|
Sprioritysearch1 |
dB |
42 |
||||
|
Sprioritysearch2 |
dB |
0 |
||||
|
SsearchE-UTRA |
dB |
Not sent |
||||
|
Threshx, high (Note 1) |
dB |
48 |
||||
|
Propagation Condition |
AWGN |
|||||
|
Note 1: This refers to the value of Threshx, high which is included in UTRA system information, and is a threshold for the E-UTRA target cell. Note 2: The UE under test shall not be continuously scheduled to ensure that it operates in DRX when the reselection is being performed. The test equipment shall schedule with a different common H-RNTI when the UE under test is not being scheduled |
||||||
Table A.5.4W: Cell specific test parameters for UTRAN to E-UTRA TDD cell reselection (cell 2)
|
Parameter |
Unit |
Cell 2 |
|
|
T1 |
T2 |
||
|
E-UTRA RF Channel number |
2 |
||
|
BWchannel |
MHz |
10 |
|
|
OCNG Patterns defined in TS 36.133 A.3.2.2.2 (OP.2 TDD) [24] |
OP.2 TDD |
||
|
PBCH_RA |
dB |
0 |
|
|
PBCH_RB |
dB |
||
|
PSS_RA |
dB |
||
|
SSS_RA |
dB |
||
|
PCFICH_RB |
dB |
||
|
PHICH_RA |
dB |
||
|
PHICH_RB |
dB |
||
|
PDCCH_RA |
dB |
||
|
PDCCH_RB |
dB |
||
|
PDSCH_RA |
dB |
||
|
PDSCH_RB |
dB |
||
|
OCNG_RANote 1 |
dB |
||
|
OCNG_RBNote 1 |
dB |
||
|
Qrxlevmin |
dBm |
-140 |
|
|
|
dBm/15 kHz |
-98 |
|
|
RSRP |
dBm/15 KHz |
-infinity |
-86 |
|
|
dB |
-infinity |
12 |
|
|
dB |
-infinity |
12 |
|
TreselectionEUTRAN |
s |
0 |
|
|
Snonintrasearch |
dB |
Not sent |
|
|
Threshserving, low |
dB |
44 |
|
|
Threshx, low (Note 2) |
dB |
42 |
|
|
Propagation Condition |
AWGN |
||
|
Note 1: OCNG shall be used such that cell 2 is fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols. Note 2: This refers to the value of Threshx, low which is included in E-UTRA system information, and is a threshold for the UTRA target cell. |
|||
A.5.5.5.4.2 Test Requirements
The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on Cell 2.
The cell re-selection delay shall be less than 66 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as: 
, where:
TSI = the maximum time allowed aquire system information from a E-UTRAN cell, 1280msec [24].
TRA = the additional delay caused by the random access procedure, 30msec [24]
TIdentify,,E-UTRAN = Time to identify an E-UTRA cell, as defined in section 8.4a.2.6.1
Thigher_priority_search is described in section 4.2.2
This gives a total of 65.70, allow 66 s in the test case.
A.5.5.5.5 Reselection to E-UTRA TDD when HS-DSCH DRX is configured (E-UTRA has lower priority)
A.5.5.5.5.1 Test Purpose and Environment
This test is to verify the requirement for the UTRAN to E-UTRAN cell reselection delay reported in section 5.5.2.1.5.
This scenario implies the presence of 1 UTRAN serving cell, and 1 E-UTRAN cell to be re-selected. The UE is requested to monitor neighbouring cells on 1 UTRAN carrier and 1 E-UTRAN carrier. Test parameters are given in Table, A.5.4X, A.5.4Y, A.5.4Z. The test consists of two successive time periods, with time duration of T1 and T2, respectively. Both UTRA cell 1 and E-UTRA cell 2 are already identified by the UE prior to the start of the test. Cell 2 is of lower priority than cell 1. Cell 1 and cell 2 shall belong to different tracking areas.
CELL_FACH with discontinuous HS-DSCH reception and with only the first DRX cycle active should be configured. The UE should not be scheduled with HS-DSCH data during T1 and T2 such that the DRX cycle becomes active.
Table A.5.4X: General test parameters for UTRAN to E-UTRAN Cell Re-selection
|
Parameter |
Unit |
Value |
Comment |
|
|
Initial condition |
Active cell |
Cell 1 |
UTRAN cell |
|
|
Neighbour cell |
Cell 2 |
E-UTRAN cell |
||
|
Final condition |
Active cell |
Cell 2 |
UE shall perform reselection to cell 2 during T2 |
|
|
HS-DSCH DRX cycleFACH |
frames |
8 |
DRX cycle length |
|
|
HS-DSCH Rx burstFACH |
frames |
1 |
On time during DRX cycle |
|
|
T321 |
msec |
100 |
Time before the DRX cycle is activated |
|
|
E-UTRA PRACH configuration |
4 |
As specified in table 5.7.1-2 in TS 36.211 |
||
|
E-UTRA access barring information |
Not sent |
No additional delays in random access procedure |
||
|
T1 |
s |
>20 |
T1 need to be defined so that cell re-selection reaction time is taken into account. |
|
|
T2 |
s |
7 |
T2 need to be defined so that cell re-selection reaction time is taken into account. |
|
Table A.5.4Y: Cell re-selection UTRAN to E-UTRAN TDD cell case (cell 1)
|
Parameter |
Unit |
Cell 1 (UTRA) |
|||
|
T1 |
T2 |
||||
|
UTRA RF Channel Number |
Channel 1 |
||||
|
CPICH_Ec/Ior |
dB |
-10 |
|||
|
PCCPCH_Ec/Ior |
dB |
-12 |
|||
|
SCH_Ec/Ior |
dB |
-12 |
|||
|
PICH_Ec/Ior |
dB |
-15 |
|||
|
HS-PDSCH_Ec/Ior (Note 2) |
dB |
-10 |
|||
|
HS-SCCH1_Ec/Ior (Note 2) |
dB |
-13 |
|||
|
OCNS_Ec/Ior |
dB |
-1.837 |
|||
|
|
dB |
11 |
-5 |
||
|
|
dBm/3,84 MHz |
-70 |
|||
|
CPICH_Ec/Io |
dB |
-10.33 |
-16.19 |
||
|
CPICH_RSCP |
dBm |
-69 |
-85 |
||
|
Propagation Condition |
AWGN |
||||
|
Cell_selection_and_ |
CPICH Ec/N0 |
||||
|
Qqualmin |
dB |
-20 |
|||
|
Qrxlevmin |
dBm |
-115 |
|||
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
|||
|
Qhyst1 |
dB |
0 |
|||
|
Treselection |
s |
0 |
|||
|
Sprioritysearch1 |
dB |
62 |
|||
|
Sprioritysearch2 |
dB |
0 |
|||
|
Threshserving, low |
dB |
36 |
|||
|
Threshx, low (Note 1) |
dB |
50 |
|||
|
Note 1: This refers to the value of Threshx, high which is included in UTRA system information, and is a threshold for the E-UTRA target cell. Note 2: The UE under test shall not be continuously scheduled to ensure that it operates in DRX when the reselection is being performed. The test equipment shall schedule with a different common H-RNTI when the UE under test is not being scheduled |
|||||
Table A.5.4Z: Cell re-selection UTRAN to E-UTRAN TDD cell case (cell 2)
|
Parameter |
Unit |
Cell 2 (E-UTRA) |
|
|
T1 |
T2 |
||
|
E-UTRA RF Channel number |
1 |
||
|
BWchannel |
MHz |
10 |
|
|
OCNG Patterns defined in A.3.2.1.1 (OP.2 TDD) |
OP.2 TDD |
||
|
PBCH_RA |
dB |
0 |
|
|
PBCH_RB |
dB |
||
|
PSS_RA |
dB |
||
|
SSS_RA |
dB |
||
|
PCFICH_RB |
dB |
||
|
PHICH_RA |
dB |
||
|
PHICH_RB |
dB |
||
|
PDCCH_RA |
dB |
||
|
PDCCH_RB |
dB |
||
|
PDSCH_RA |
dB |
||
|
PDSCH_RB |
dB |
||
|
OCNG_RANote 1 |
dB |
||
|
OCNG_RBNote 1 |
dB |
||
|
Qrxlevmin |
dBm |
-140 |
|
|
|
dBm/15 kHz |
-98 |
|
|
RSRP |
dBm/15 KHz |
-84 |
-84 |
|
|
dB |
14 |
14 |
|
|
dB |
14 |
14 |
|
TreselectionEUTRAN |
s |
0 |
|
|
Snonintrasearch |
dB |
50 |
|
|
Threshx, high |
dB |
40 |
|
|
Propagation Condition |
AWGN |
||
|
Note 1: OCNG shall be used such that cell 2 is fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols. Note 2: This refers to the value of Threshx, high which is included in E-UTRA system information, and is a threshold for the UTRA target cell |
|||
A.5.5.5.5.2 Test Requirements
The cell reselection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on Cell 2.
The cell re-selection delay shall be less than 5.7 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
, where:
TSI = the maximum time allowed aquire system information from a E-UTRAN cell, 1280msec [24].
TRA = the additional delay caused by the random access procedure, 30msec [24]
TIdentify,,E-UTRAN = Time to identify an E-UTRA cell, as defined in section 8.4a.2.6.1
This gives a total of 5.61 s, allow 5.7s in the test case.
A5.5.5.6 Reselection to E-UTRA TDD when HS-DSCH 2nd DRX is configured configured (E-UTRA has higher priority)
A.5.5.5.6.1 Test Purpose and Environment
This test is to verify the requirement for the UTRA FDD to E-UTRA TDD inter-RAT cell reselection delay reported in section 5.5.2.1.5
The test scenario comprises two different cells, with cell 1 being the UTRA serving cell and cell 2 being the E-UTRA cell to be re-selected to. Test parameters are given in Tables A.5.4ZA, A.5.4ZB, A.5.4ZC. The test consists of two successive time periods, with time duration of T1, T2. UTRA cell 1 is already identified by the UE prior to the start of the test. Cell 2 shall have higher priority than Cell 1.
Cell 1 and cell 2 shall belong to different tracking areas. Furthermore, UE has not registered with network for the tracking area containing cell 2.
CELL_FACH with discontinuous HS-DSCH reception and 2nd DRX cycle should be configured. The UE should not be scheduled with HS-DSCH data during T1 and T2 such that the DRX cycle becomes active
Table A.5.4ZA: General test parameters for UTRAN to E-UTRA TDD Cell Reselection
|
Parameter |
Unit |
Value |
Comment |
|
|
Initial condition |
Active cell |
Cell1 |
||
|
T2 end condition |
Active cell |
Cell2 |
UE shall perform reselection to cell 2 during T2 |
|
|
Neighbour cell |
Cell1 |
|||
|
HS-DSCH second DRX cycleFACH |
frames |
512 |
Length of the DRX cycle |
|
|
HS-DSCH second Rx burstFACH |
frames |
1 |
On time during DRX cycle |
|
|
T329 |
msec |
500 |
Number of seconds until the DRX cycle is initiated |
|
|
DRX level |
Single level DRX |
Second DRX only active |
||
|
HCS |
Not used |
|||
|
E-UTRA PRACH configuration |
4 |
As specified in table 5.7.1-2 in TS 36.211 |
||
|
E-UTRA access barring information |
Not sent |
No additional delays in random access procedure |
||
|
T1 |
s |
>20 |
During T1, cell 2 shall be powered off, and during the off time its physical cell identity shall be changed. The intention is to ensure that cell 2 has not been detected by the UE prior to the start of period T2. |
|
|
T2 |
s |
70 |
T2 needs to be defined so that cell re-selection reaction time is taken into account. |
|
Table A.5.4ZB: Cell specific test parameters for UTRAN to E-UTRA TDD cell reselection (cell 1)
|
Parameter |
Unit |
Cell 1 (UTRA) |
||||
|
T1 |
T2 |
|||||
|
UTRA RF Channel Number |
Channel 1 |
|||||
|
CPICH_Ec/Ior |
dB |
-10 |
||||
|
PCCPCH_Ec/Ior |
dB |
-12 |
||||
|
SCH_Ec/Ior |
dB |
-12 |
||||
|
PICH_Ec/Ior |
dB |
-15 |
||||
|
HS-PDSCH_Ec/Ior |
dB |
-10 |
||||
|
HS-SCCH1_Ec/Ior |
dB |
-13 |
||||
|
OCNS_Ec/Ior |
dB |
-1.837 |
||||
|
|
dB |
13 |
13 |
|||
|
|
dBm/3,84 MHz |
‑70 |
||||
|
CPICH_Ec/Io |
dB |
-10.21 |
-10.21 |
|||
|
CPICH_RSCP |
dBm |
-67 |
-67 |
|||
|
Qqualmin |
dB |
-20 |
||||
|
Qrxlevmin |
dBm |
-115 |
||||
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
||||
|
Treselection |
s |
0 |
||||
|
Sprioritysearch1 |
dB |
42 |
||||
|
Sprioritysearch2 |
dB |
0 |
||||
|
SsearchE-UTRA |
dB |
Not sent |
||||
|
Threshx, high (Note 1) |
dB |
48 |
||||
|
Propagation Condition |
AWGN |
|||||
|
Note 1: This refers to the value of Threshx, high which is included in UTRA system information, and is a threshold for the E-UTRA target cell. Note 2: The UE under test shall not be continuously scheduled to ensure that it operates in DRX when the reselection is being performed. The test equipment shall schedule with a different common H-RNTI when the UE under test is not being scheduled |
||||||
Table A.5.4ZC: Cell specific test parameters for UTRAN to E-UTRA TDD cell reselection (cell 2)
|
Parameter |
Unit |
Cell 2 |
|
|
T1 |
T2 |
||
|
E-UTRA RF Channel number |
2 |
||
|
BWchannel |
MHz |
10 |
|
|
OCNG Patterns defined in TS 36.133 A.3.2.2.2 (OP.2 TDD) [24] |
OP.2 TDD |
||
|
PBCH_RA |
dB |
0 |
|
|
PBCH_RB |
dB |
||
|
PSS_RA |
dB |
||
|
SSS_RA |
dB |
||
|
PCFICH_RB |
dB |
||
|
PHICH_RA |
dB |
||
|
PHICH_RB |
dB |
||
|
PDCCH_RA |
dB |
||
|
PDCCH_RB |
dB |
||
|
PDSCH_RA |
dB |
||
|
PDSCH_RB |
dB |
||
|
OCNG_RANote 1 |
dB |
||
|
OCNG_RBNote 1 |
dB |
||
|
Qrxlevmin |
dBm |
-140 |
|
|
|
dBm/15 kHz |
-98 |
|
|
RSRP |
dBm/15 KHz |
-infinity |
-86 |
|
|
dB |
-infinity |
12 |
|
|
dB |
-infinity |
12 |
|
TreselectionEUTRAN |
s |
0 |
|
|
Snonintrasearch |
dB |
Not sent |
|
|
Threshserving, low |
dB |
44 |
|
|
Threshx, low (Note 2) |
dB |
42 |
|
|
Propagation Condition |
AWGN |
||
|
Note 1: OCNG shall be used such that cell 2 is fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols. Note 2: This refers to the value of Threshx, low which is included in E-UTRA system information, and is a threshold for the UTRA target cell. |
|||
A.5.5.5.6.2 Test Requirements
The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on Cell 2.
The cell re-selection delay shall be less than 66 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as: 
, where:
TSI = the maximum time allowed aquire system information from a E-UTRAN cell, 1280msec [24].
TRA = the additional delay caused by the random access procedure, 30msec [24]
TIdentify,,E-UTRAN = Time to identify an E-UTRA cell, as defined in section 8.4a.2.6.1
Thigher_priority_search is described in section 4.2.2
This gives a total of 65.70, allow 66 s in the test case.
A.5.5.5.7 Reselection to E-UTRA FDD with FACH measurement occasions configured
A.5.5.5.7.1 Test Purpose and Environment
This test is to verify the requirement for the UTRAN to E-UTRA cell re-selection delay reported in section 5.5.2.1.5 with measurement occasions configured.
This scenario implies the presence of 1 UTRAN serving cell, and 1 E-UTRA FDD cell to be re-selected. The UE is requested to monitor neighbouring cells on 2 UMTS carriers, 12 GSM cells and 1 E-UTRA FDD carrier. Test parameters are given in Table, A.5.4ZF, A.5.4ZG and A.5.4ZH. During time phase T1, the E-UTRA cell can be identified but is not sufficiently strong to trigger reselection. Cell 2 is of higher priority than cell 1. The GERAN neighbour cells are not assigned any absolute priority.
The transport and physical parameters of the S-CCPCH carrying the FACH are defined in Table A.5.4ZD and Table A.5.4ZE.
Table A.5.4ZD: Physical channel parameters for S-CCPCH.
|
Parameter |
Unit |
Level |
|
Channel bit rate |
Kbps |
60 |
|
Channel symbol rate |
Ksps |
30 |
|
Slot Format #I |
– |
4 |
|
TFCI |
– |
OFF |
|
Power offsets of TFCI and Pilot fields relative to data field |
dB |
0 |
Table A.5.4ZE: Transport channel parameters for S-CCPCH
|
Parameter |
FACH |
|
Transport Channel Number |
1 |
|
Transport Block Size |
240 |
|
Transport Block Set Size |
240 |
|
Transmission Time Interval |
10 ms |
|
Type of Error Protection |
Convolution Coding |
|
Coding Rate |
½ |
|
Rate Matching attribute |
256 |
|
Size of CRC |
16 |
|
Position of TrCH in radio frame |
Fixed |
Table A.5.4ZF General test parameters for UTRAN to E-UTRA Cell Re-selection
|
Parameter |
Unit |
Value |
Comment |
|
|
Initial condition |
Active cell |
Cell1 |
||
|
Neighbour cell |
Cell2 |
|||
|
Final condition |
Active cell |
Cell2 |
||
|
HCS |
Not used |
|||
|
T1 |
S |
9 |
||
|
T2 |
S |
3 |
||
|
FACH Measurement occasion cycle length coefficient |
3 |
N_TTI=1 |
||
|
GSM neighbour cell list |
Includes 12 GSM Cells |
|||
|
UTRA intrafrequency neighbour cell list |
Includes cell 1 and 23 other cells on channel 1 |
|||
|
UTRA interfrequency neighbour cell list |
Includes 24 interfrequency neighbour cells on UARFCN channel 3 |
|||
|
E-UTRA cell list |
Includes channel 2 |
|||
|
CELL_FACH Absolute Priority Measurement Indicator |
All layers |
|||
Table A.5.4ZG: Cell re-selection UTRAN to E-UTRA cell case (cell 1)
|
Parameter |
Unit |
Cell 1 (UTRA) |
|
|
T1 |
T2 |
||
|
UTRA RF Channel Number |
Channel 1 |
||
|
CPICH_Ec/Ior |
dB |
-10 |
|
|
PCCPCH_Ec/Ior |
dB |
-12 |
|
|
SCH_Ec/Ior |
dB |
-12 |
|
|
PICH_Ec/Ior |
dB |
-15 |
|
|
S-CCPCH_Ec/Ior |
dB |
-12 |
|
|
OCNS_Ec/Ior |
dB |
-1.294 |
|
|
|
dB |
0 |
|
|
|
dBm/3,84 MHz |
‑69 |
|
|
CPICH_Ec/Io |
dB |
-13 |
|
|
CPICH_RSCP |
dBm |
-79 |
|
|
Propagation Condition |
AWGN |
||
|
Cell_selection_and_ |
CPICH RSCP |
||
|
Qqualmin |
dB |
-20 |
|
|
Qrxlevmin |
dBm |
-115 |
|
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
|
|
Qoffset1s, n |
dB |
C1, C2: 0 |
|
|
Qhyst1 |
dB |
0 |
|
|
Treselection |
S |
0 |
|
|
SsearchRAT |
dB |
Not sent |
|
|
Sprioritysearch1 |
dB |
0 |
|
|
Sprioritysearch2 |
dB |
0 (default) |
|
|
SsearchE-UTRA |
dB |
Not sent |
|
|
Threshx, high (Note 1) |
dB |
48 |
|
|
Propagation Condition |
AWGN |
||
|
Note 1: This refers to the value of Threshx, high which is included in UTRA system information, and is a threshold for the E-UTRA target cell. |
|||
Table A.5.4ZH: Cell re-selection UTRAN to E-UTRA cell case (cell 2)
|
Parameter |
Unit |
Cell 2 |
|
|
T1 |
T2 |
||
|
E-UTRA RF Channel number |
2 |
||
|
BWchannel |
MHz |
10 |
|
|
OCNG Patterns defined in TS 36.133 A.3.2.1.2 (OP.2 FDD) [24] |
OP.2 FDD |
||
|
PBCH_RA |
dB |
0 |
|
|
PBCH_RB |
dB |
||
|
PSS_RA |
dB |
||
|
SSS_RA |
dB |
||
|
PCFICH_RB |
dB |
||
|
PHICH_RA |
dB |
||
|
PHICH_RB |
dB |
||
|
PDCCH_RA |
dB |
||
|
PDCCH_RB |
dB |
||
|
PDSCH_RA |
dB |
||
|
PDSCH_RB |
dB |
||
|
OCNG_RANote 1 |
dB |
||
|
OCNG_RBNote 1 |
dB |
||
|
Qrxlevmin |
dBm |
-140 |
|
|
|
dBm/15 kHz |
-98 |
|
|
RSRP |
dBm/15 KHz |
-98 |
-86 |
|
|
dB |
0 |
12 |
|
|
dB |
0 |
12 |
|
TreselectionEUTRAN |
S |
0 |
|
|
Snonintrasearch |
dB |
Not sent |
|
|
Threshserving, low |
dB |
30 |
|
A.5.5.5.7.2 Test Requirements
The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on Cell 2.
The cell re-selection delay shall be less than 2.5 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE1: The cell re-selection delay can be expressed as:
ms
where
Tmeasurement,,E-UTRAN = Time to measure E-UTRA RSRP or RSRQ, as defined in section 8.4.2.6.2, 1120ms.
TBCCH = The maximum time allowed to read BCCH data from the E-UTRAN cell, 1280ms [24].TRA = the additional delay caused by the random access procedure, 30msec [24]
This gives a total of 2460ms, allow 2.5 seconds in the test case.
NOTE2: The reselection delay is based on Nfreq=2 since measurements of GERAN are not required by the higher layers in this scenario.
A.5.5.5.8 Reselection to E-UTRA TDD with FACH measurement occasions configured
A.5.5.5.8.1 Test Purpose and Environment
This test is to verify the requirement for the UTRAN to E-UTRA cell re-selection delay reported in section 5.5.2.1.5 with measurement occasions configured.
This scenario implies the presence of 1 UTRAN serving cell, and 1 E-UTRA TDD cell to be re-selected. The UE is requested to monitor neighbouring cells on 2 UMTS carriers, 12 GSM cells and 1 E-UTRA TDD carrier. Test parameters are given in Table, A.5.4ZK, A.5.4ZL and A.5.5.4ZM. During time phase T1, the E-UTRA cell can be identified but is not sufficiently strong to trigger reselection. Cell 2 is of higher priority than cell 1. The GERAN neighbour cells are not assigned any absolute priority.
The transport and physical parameters of the S-CCPCH carrying the FACH are defined in Table A.5.4ZI and Table A.5.4ZJ.
Table A.5.4ZI: Physical channel parameters for S-CCPCH.
|
Parameter |
Unit |
Level |
|
Channel bit rate |
Kbps |
60 |
|
Channel symbol rate |
Ksps |
30 |
|
Slot Format #I |
– |
4 |
|
TFCI |
– |
OFF |
|
Power offsets of TFCI and Pilot fields relative to data field |
dB |
0 |
Table A.5.4ZJ: Transport channel parameters for S-CCPCH
|
Parameter |
FACH |
|
Transport Channel Number |
1 |
|
Transport Block Size |
240 |
|
Transport Block Set Size |
240 |
|
Transmission Time Interval |
10 ms |
|
Type of Error Protection |
Convolution Coding |
|
Coding Rate |
½ |
|
Rate Matching attribute |
256 |
|
Size of CRC |
16 |
|
Position of TrCH in radio frame |
Fixed |
Table A.5.4ZK General test parameters for UTRAN to E-UTRA Cell Re-selection
|
Parameter |
Unit |
Value |
Comment |
|
|
Initial condition |
Active cell |
Cell1 |
||
|
Neighbour cell |
Cell2 |
|||
|
Final condition |
Active cell |
Cell2 |
||
|
HCS |
Not used |
|||
|
T1 |
S |
9 |
||
|
T2 |
S |
3 |
||
|
FACH Measurement occasion cycle length coefficient |
3 |
N_TTI=1 |
||
|
GSM neighbour cell list |
Includes 12 GSM Cells |
|||
|
UTRA intrafrequency neighbour cell list |
Includes cell 1 and 23 other cells on channel 1 |
|||
|
UTRA interfrequency neighbour cell list |
Includes 24 interfrequency neighbour cells on UARFCN channel 3 |
|||
|
E-UTRA cell list |
Includes channel 2 |
|||
|
CELL_FACH Absolute Priority Measurement Indicator |
All layers |
|||
Table A.5.4ZL: Cell re-selection UTRAN to E-UTRA cell case (cell 1)
|
Parameter |
Unit |
Cell 1 (UTRA) |
|
|
T1 |
T2 |
||
|
UTRA RF Channel Number |
Channel 1 |
||
|
CPICH_Ec/Ior |
dB |
-10 |
|
|
PCCPCH_Ec/Ior |
dB |
-12 |
|
|
SCH_Ec/Ior |
dB |
-12 |
|
|
PICH_Ec/Ior |
dB |
-15 |
|
|
S-CCPCH_Ec/Ior |
dB |
-12 |
|
|
OCNS_Ec/Ior |
dB |
-1.294 |
|
|
|
dB |
0 |
|
|
|
dBm/3,84 MHz |
‑69 |
|
|
CPICH_Ec/Io |
dB |
-13 |
|
|
CPICH_RSCP |
dBm |
-79 |
|
|
Propagation Condition |
AWGN |
||
|
Cell_selection_and_ |
CPICH RSCP |
||
|
Qqualmin |
dB |
-20 |
|
|
Qrxlevmin |
dBm |
-115 |
|
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
|
|
Qoffset1s, n |
dB |
C1, C2: 0 |
|
|
Qhyst1 |
dB |
0 |
|
|
Treselection |
S |
0 |
|
|
SsearchRAT |
dB |
not sent |
|
|
Sprioritysearch1 |
dB |
0 |
|
|
Sprioritysearch2 |
dB |
0 (default) |
|
|
SsearchE-UTRA |
dB |
Not sent |
|
|
Threshx, high (Note 1) |
dB |
48 |
|
|
Propagation Condition |
AWGN |
||
|
Note 1: This refers to the value of Threshx, high which is included in UTRA system information, and is a threshold for the E-UTRA target cell. |
|||
Table A.5.4ZM: Cell re-selection UTRAN to E-UTRA cell case (cell 2)
|
Parameter |
Unit |
Cell 2 |
|
|
T1 |
T2 |
||
|
E-UTRA RF Channel number |
2 |
||
|
BWchannel |
MHz |
10 |
|
|
OCNG Patterns defined in A.3.2.1.1 (OP.2 TDD) |
OP.2 TDD |
||
|
PBCH_RA |
dB |
0 |
|
|
PBCH_RB |
dB |
||
|
PSS_RA |
dB |
||
|
SSS_RA |
dB |
||
|
PCFICH_RB |
dB |
||
|
PHICH_RA |
dB |
||
|
PHICH_RB |
dB |
||
|
PDCCH_RA |
dB |
||
|
PDCCH_RB |
dB |
||
|
PDSCH_RA |
dB |
||
|
PDSCH_RB |
dB |
||
|
OCNG_RANote 1 |
dB |
||
|
OCNG_RBNote 1 |
dB |
||
|
Qrxlevmin |
dBm |
-140 |
|
|
|
dBm/15 kHz |
-98 |
|
|
RSRP |
dBm/15 KHz |
-98 |
-86 |
|
|
dB |
0 |
12 |
|
|
dB |
0 |
12 |
|
TreselectionEUTRAN |
S |
0 |
|
|
Snonintrasearch |
dB |
Not sent |
|
|
Threshserving, low |
dB |
30 |
|
A.5.5.5.8.2 Test Requirements
The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Tracking Area Update procedure on Cell 2.
The cell re-selection delay shall be less than 2.5 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE1: The cell re-selection delay can be expressed as:
ms
where
Tmeasurement,,E-UTRAN = Time to measure E-UTRA RSRP or RSRQ, as defined in section 8.4.2.6.2, 1120ms.
TBCCH = The maximum time allowed to read BCCH data from the E-UTRAN cell, 1280ms [24].
TRA = the additional delay caused by the random access procedure, 30msec [24]
This gives a total of 2460ms, allow 2.5 seconds in the test case.
NOTE2: The reselection delay is based on Nfreq=2 since measurements of GERAN are not required by the higher layers in this scenario.